GE DISR473CG0WW, DISR473CG1WW, DISR473CG2WW, DISR473CG5WW, DISR473CG6WW Installation Guide

...
31
Note: Installation of this dryer requires basic mechanical and electrical sldlls.
It is your responsibility to contact a qualified electrical installer tomake the electrical connection.
WARNING- POTENTIALFIREAND SHOCKHAZARD
Use onlyrigid or flexible metal 100 nun (4") diameter ductwork for exhausting to the outdoors. Never use plastic or other combustible ductwork.
This appliance must be properly grounded (earthed) and installed as described in these instructions and governing codes.
Do not install or store appliance in an area where it will be exposed to water/weather.
Exhausting the dryer to the outdoors is strongly
recommended to prevent large amounts of moisture
and lint from being blown into the room.
Before the old dryer is removed from service or discarded, remove the door to the drying compartment.
Service information and wiring diagram are located in control console.
Installation
Step 1
Remove and save literature and parts package flom
(hyer drum.
Step 2
Lay carton corner posts or two boards
on floor. I,ay (hyer on its back.
Step 3
Relnove fi)aln shipping pads by
pulling at sides and breaking away flom duet legs. Be sure to remove all timm pieces flom around legs.
Step 4
Stand (hyer upright.
Step 5
Move (hTer to desired operating location.
_Pull hereto separate
from front leg
__i Dryer legs
I V _ Pull here to separate
Foam shipping pads from rear leg
Toolsand Materials you will need
Slip joint pliers
Screwdrivers (slotted or Phillips head)
One 3/4" recognized strain relief
4 inch dia. rind metal duct, elbows and exhaust hood.
Basic safety protection such as safety goggles, gloves,
and arm protection is recommended.
Step 6
A(ljust leveling legs to match washer height. IhTer must
be level and rest firmly on all four leveling legs.
Step 7
Connect to power supply.
(See ELE( TRICAI_ CONNE( TION INFORMATION
section of this instruction.)
Step 8
Connect external exhaust or deflector. (See EXHAUST INFORMATION section of this instruction.)
Step 9
Check for proper operation.
Step 10
Place Owner's Manual and installation instructions in a location where they may be found by the
CtlStOlIler.
500A187P031 49-90048 o2-ooJR 31-16027
Electrical Connection Information
A
hlk WARNING: TO REDUCETHERISK OFFIRE,
ELECTRICSHOCK,OR PERSONALINJURY
DO NOT USE AN EXTENSION CORD
WITH THIS APPLIANCE.
THIS APPLIANCE MUST BE PROPERLY GROUNDED (EARTHED).
Dryer must be electrically grounded (earthed) in
accordance with local codes and ordinances.
IF THEDRYERIS SUPPLIEDWITH A FLEXIBLEPOWERCORD
Plug the cordset into its own separate grounded outlet. DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE GROUND PRONG FROM THE POWER CORD.
IF THEDRYERIS SUPPLIEDWITH A TERMINALBLOCK
Electrical requirements:
The operating vohage (volts), amperage (amps) or wattage (watts) and flequency (Hz) of your (hyer are indicated on the rating plate located on the upper
right corner of the door opening.
The (hyer must be connected to an individual branch circuit corresponding to that indicated on the rating
plate and protected by the required time-delay fl_ses or circuit breakers in accordance with governing codes.
If the electrical supply does not meet what is indicated on the rating plate, call a licensed electrician.
ASSUREGROUND(EARTH)WIRE IS PROPERLYCONNECTED
MAKESURESCREWSARE BROWN STRAINRELIEF PROPERLYTIGHTENED BRACKET
USEPROPER STRAINRELIEF
WIRING DIAGRAM AND SOME SERVICEINFORMATIONLOCATEDIN CONTROLHOUSING
1. Remove cover near the power supply ent_ y hole.
2. Install 3/4 inch, recognized strain relief to power ent_y
hole. Bring power supply through strain relief.
3. Connect power supply as ti)llows:
A. Live (brown) line to upper screw of terminal block
(marked L1 ).
B. Neutral (blue) line to center screw of terminal block
(marked N).
4. Attach ground (earth) wire (green, green and yellow, or bare) to the green ground screw (hole above strain relief bracket). Tighten all terminal
block screws firmly.
5. Properly secure power supply to strain relief.
6. Reinstall the cover.
POWERSUPPLYCORD 220/240VAC30A
WARNING: NEVER LEAVE THE TERMINAL BLOCK WITHOUT THE COVER.
Loading...
+ 2 hidden pages