Page 1
Code Changes
Page 2
Page 3
Note
The system will not accept
the same code for two different users.
P r e s s t o t u r n
2
P r e s s t o t u r n
P r e s s t o
A
m o v e b a c k w a r d
t h r o u g h
t h e m e n u
P r e s s t o
m o v e f o r w a r d
t h r o u g h
t h e m e n u
P r e s s n u m b e r e d
k e y s w h e n
v a l u e s o r c o d e
c h o i c e s a r e
r e q u e s t e d
Figure 3. Navigating Through Menus
Test System Weekly
A
B
B
C
D
P r e s s t o d e s e l e c t
a f e a t u r e o n
1
a f e a t u r e o f f
Off
12
press both
No Delay
4
press both
Features
7
press both
Status
*
‚
a n o p t i o n o r t o
c a n c e l a n e n t r y
Stay
Away
3
Silent
Pager
5
6
System
Menu
8
9
Lights
Bypass
0
#
P r e s s t o s e l e c t
ƒ
a n o p t i o n o r t o
a c c e p t a n e n t r y
Examples of Programming Using Menus
Here are two examples of programming using system menus. The examples describe each step
involved in programming a user code and in erasing a user code from a fixed display touchpad.
To change or assign a user access code:
¾
1. Enter the programming menus by pressing 9 + System Master Code.
2. Press
3. Press
4. For example, if you want to change a Regular User code, press
5. Press
B until the touchpad displays “USER CODES,” then press ƒ.
B until the touchpad displays the type of code you wish to change (Regular User codes
or System Master code), then press
ƒ.
ƒ when the touchpad dis-
plays “REG CODES.”
B until the touchpad displays the user code you wish to change, then press ƒ.
Note
You cannot delete the System Master Code.
For example, if you want to change Regular User code 2, press
ƒ when the touchpad dis-
plays “REG CODE 02.”
6. Enter the new code and press
7. Press
8. Press
9. Press
¾
B. “BYPASS on/off” appears:
•Press
•Press
1 + ƒ to turn the option off for this user code.
2 + ƒ to turn the option on for this user code.
B. “TESTS on/off” appears:
•Press
•Press
1 + ƒ to turn the option off for this user code.
2 + ƒ to turn the option on for this user code.
‚ + B to move to the next user code, or ‚ + 4 + ƒ to exit programming menus.
To erase a user code:
ƒ.
1. Enter the programming menus by pressing 9 + System Master Code.
2. Press
B until the touchpad displays “USER CODES,” then press ƒ.
3. The touchpad displays “REG CODES.” Press ƒ.
4. Press
B until the touchpad displays the user code you wish to erase, then press ƒ.
For example, if you want to change User code 4, press
ƒ when the touchpad displays “REG
CODE 04,” or “USER 04.”
5. Enter the System Master code you used in Step 1 and press
ƒ. The deleted code appears as
“REG 04 ----”.
6. Press
‚ + B to move to the next user code, or ‚ +4 + ƒ to exit the programming
menus.
30
Loading...