GE Compact Fluorescent Specification Sheet

GE

INDOOR LIGHTING

g

Lighting Solutions

GUIDE FORM SPECIFICATIONS
GARAGE GUARDIAN™ LUMINAIRE CFL

Low Bay Enclosed

GENERAL DESCRIPTION

The complete luminaire designated _____ (identify) shall be
a GE GARAGE GUARDIAN™ luminaire with, ordering number
_____ (specify GBP or GBC, plus ordering number logic from
catalog) or approved equal, to operate _____ (specify [two 42]
watt or [four 42] watt) 4-pin compact fluorescent lamps from a
nominal _____(specify 120, 208, 240 or 277) volt 60 Hz or (110,
220, 230 or 240) volt 50 Hz power source. The luminaire shall
include a completely prewired integral ballast and optical as­sembly. The luminaire shall be suitable for continuous service
indoors in a maximum ambient temperature of 40
minaire shall be UL Listed SUITABLE FOR DAMP LOCATIONS or
UL LISTED FOR WET LOCATIONS depending on mounting, and
C-UL ,(Canadian) Listed for Indoor Locations.

MECHANICAL CONSTRUCTION

The luminaire shall be shipped as a completely assembled
fixture including 4-pin lamps installed.

The ballast housing and optical assembly shall be provided
with easy-to-read moisture-resistant nameplates which can be
seen without disturbing the installed luminaire.

The luminaire shall include provision for optional field mounting
of safety chain.

The ballast housing shall be made of die-cast aluminum. The
ballast housing shall have a polyester powder paint finish .

The luminaire shall include a _____ (specify mounting code)
mounting from the following optional mounting configurations:

10 = Surface Mtg. (Junction-box not included)
11 = 3/4" Rigid Pendant
12 = 3/4" Pendant With Bird Shield*
13 = 3/4"Flex Pendant Adjustable
01 = Primary Electrical Disconnect With MPM-C
02 = Primary Electrical Disconnect With MPM-3PR
03 = Primary Electrical Disconnect With MPM-3PF
04 = Primary Electrical Disconnect With MPM-3PRFW
05 = Primary Electrical Disconnect With MPM-3PRTFW
06 = Primary Electrical Disconnect With MPM-WW
92 = Individual ballast leads provided for switched light
levels / individual ballast circuiting

°

C. The lu-

BALLAST OPERATION

The luminaire shall contain electronic ballast(s)* in full compli­ance with lamp-ballast specifications available to the fixture
manufacturer from the lamp manufacturers at the time of
fixture manufacture.

The ballast shall reliably start and operate the lamp in ambient
temperatures down to 0

°

F (-18°C).

OPTICAL ASSEMBLY

The optical assembly shall be enclosed and gasketed to
prevent entrance of particulate contaminants. The refractor
shall be UV stabilized injection molded prismatic heat-resistant
acrylic or optional impact resistant polycarbonate optic and
lens.

The optical shall have downlight cutoff classification with up­light window and either clear or painted lower refractor band;
and have optional field adjustable internal uplight shielding.

* REFER TO PRODUCT PAGE IN GELS PRODUCT CATALOG FOR
OTHER BALLAST SELECTIONS. FOR MORE DEFINITIVE ELECTRI­CAL INFORMATION, REFER TO BALLAST SPECIFICATIONS IN
TECHNICAL DATA SECTION.

NOTE:
Bird Shield Adds 4.4" To Overall Height

* See GELS Product Selection Guide for MPM mounting details.

Guide Form Specifications – 2011

g

GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com

1 6 9 4 3 5 3 3- - -- 8 8 8

GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company.
© 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.