Page 1
GE
Lighting
AlbeoTM LED Luminaire
Linear Lighting
(ALM1 Series)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING/AVERTISSEMENT
RISK OF ELECTRIC SHOCK
• Turn power off before inspection, installation or removal.
• Properly ground electrical enclosure.
RISK OF FIRE
• Follow all NEC and local codes.
• Use only UL or IEC approved wire for input/output connections.
Minimum size 18 AWG.
RISQUES DE DÉCHARGES ÉLECTRIQUES
• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.
• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.
RISQUES D’INCENDIE
• Respectez tous les codes NEC et codes locaux.
• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de
connexion. Taille minimum 18 AWG.
Installation Guide
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (A)/NMB-3(A)
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Save These Instructions
Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
• The LED driver must be supplied with 120-277 VAC, 50/60
Hz per product label and connected to an individual properly
grounded branch circuit, protected by a 15 or 20 ampere
circuit breaker.
Grounding Instructions
• The grounding and bonding of the overall system shall be
done in accordance with National Electric Code (NEC) Article
600 and local codes.
Tools and Components Required:
• ALM1 Series xture
• Mounting hardware (not Included)
• #2 Phillips screwdriver
• Drill
imagination at work
Page 2
Unit Installation
For safety, turn off main power prior to installation.
1
Remove LED plate
Before installation, loosen two screws on side of xture,
2
and open by holding lenses and sliding LED plate away
from screws.
Remove appropriate knockout in xture for power input. Install box to intended surface using mounting holes
4 5
Remove red wire and blue wire which lead to the power
3
supply from connectors, and remove LED plate from box
by rotating LED plate 90° and sliding the plate towards
the box until the hinges can be removed.
Fasten to ceiling with appropriate hardware
on both ends of xture with appropriate mounting
hardware. If mounting into a joist, use 2 wood screws
and 2 washers to attach to joist. If joist is not available,
use 2 toggle bolts and 2 washers to attach to plasterboard.
AC line
LED driver
Connect the black (line) and white (neutral) wires of the
6 7
AC line to the similarly colored wires of the xture’s LED
driver using UL listed wire connectors. Connect the green
(ground) to the lug inside the xture.
Reinsert the LED plate into the box so that it is hanging
open by the hinges.
Page 3
Reattach red wire and blue wire into connectors, and
8
give wires a rm tug to conrm proper connection.
Restore main power.
10
Tuck wires inside and close LED plate. Reinsert screws
9
into LED plate on side of xture making sure to pull the
LED plate rmly against the screw side of box.
GE Lighting • 1-888-MY-GE-LED (1-888-69-43-533) • www.gelighting.com
The GE brand, logo, and Albeo are trademarks of the General Electric Company.
© 2014 GE Lighting , LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory
conditions.
ALB009-031014
Loading...