GE ALM1 Data Sheet

GE
Lighting
Albeo
Linear Surface Mount Lighting
LED Luminaire
imagination at work
Product Features
Albeo ™ ALM1-Series luminaire provides an energy efficient, low maintenance alternative to traditional fluorescent fixtures with bare lamps or wrap lenses. Light output is equivalent to a four lamp fluorescent fixture at 33% less power.
Applications
Designed to meet recommended luminance and illuminance requirements for low bay and task level applications. Applications include stair well, parking garage, and back-of-house in office, education, library, health, retail, and data center settings.
Housing
• All-aluminum channel.
LED & Optical Assembly
Top quality wrap lensing provides low contrast, low glare light using the brightest and highest efficacy LEDs.
Utilizes high brightness LEDs, 70 and 80 CRI at 4000K & 5000K typical.
• LM-79, LM-80 tests and reports are performed in accordance to IESNA standards.
Ratings
• CSA damp location.
• Temperature Rated at –30°C to +40°C (-22°F to +104° F)
Projected L70 (15K) > 100,000 Life Hours per IES TM-21.
Mounting
Fixture is designed to be mounted directly to surface wall or ceiling. Fixture knock access wiring to connect to electrical box.
outs allow
Finish
White polyester powder coat.
Controls
Motion sensors can be combined for additional energy savings.
Electrical
• 120-277 volt
• System power factor is >90%* and THD <20%.*
Integral surge protection: For 120-277VAC per IEEE/ANSI C62 41.1:1991, 4kV IEC 61000-4-12.
• EMI: Title 47 CFR Part 15 Class A.
* System power factor and THD is tested and specified at
120V input and maximum load conditions.
Warranty
• 5-year limited system warranty standard.
Ordering Number Logic
Linear Surface Mount Lighting (ALM1
-Series)
A L M 1 0 S T W _ _ _ _ - _ - _ - _ - _ _ - _ - _ - _ - _ - _ - _ _ - _ - _
PRODUCT
ID
A = Albeo
L = Linear
M = Surface
Mount
1 = LED Generation
MODULE
#
CURRENT
VOLTAGE MODULE
0 = 120/277 70 Plus CRI
DRIVE
1 = 1 module 2 = 2 modules
LENGTH
DRIVE
CURRENT
T = Standard H = High Output
TYPICAL INITIAL
LUMENS 70 CRI
4000K
LED COLOR
47 = 4000K 57 = 5000K
80 Plus CRI 48 = 4000K 58 = 5000K
5000K
TEMP
W = Wrap C = Channel
120-277V
WAT TS
LENS
TYPES
5000K
OPTICS
BEAM
Wrap Lens 1 = 120° D = 120°
Diffused lens
Channel Lens 1 = 120° 2 =20° 4 = 40° D = 120°
Diffused lens
W = Wide
LPW
FIXTURE LENGTH
2 = 2ft 4 = 4ft
MOTION/DAYLIGHT
SENSOR
N = None A = On/off aisle motion B = On/off 360 motion C = On/off cold temp aisle D = On/off cold temp 360 E = Daylight sensor F = Aisle motion/daylight G = 360 motion/daylight H = Pre-wired (no sensor)
If you choose options below you must choose control wiring option V or D J = 0-10V Motion 360 K = 0-10V Motion aisle L = 0-10V Motion 360 cold M = 0-10V Motion aisle cold
CONTROL
N = None V = 0-10V
Stand alone
D = 0-10V
Daisy chain
WIRING
MOUNTING FINISH
ST = Standard
Surface
Mount
N
CORD &
PLUG
N = None Knock outaccess
W = White
Powdercoat
1 T 2 1870 1890 24 79 1 H 2 2550 2570 33 78
2
1
1
T
T
H
2
3745 3780 42 90 4 3745 3780 42 90 4
5100 5145 59 87
2 T 4 7490 7555 78 97
MODULE
#
DRIVE
CURRENT
LENGTH
TYPICAL INITIAL
LUMENS 80 CRI
4000K
5000K
WAT TS
120-277V
5000K
LPW
1 T 2 1655 1680 24 70 1 H 2 2250 2290 33 70
2
1
1
T
T H
2
4 3305 3360 42 80 4
3305 3360 42 80
4500 4575 59 77
2 T 4 6610 6720 78 87
Note: Lumen data shown is for 120 (1) optic. See table to the right for other light optic factors.
OPTICS BEAM % OUTPUT
Wrap Lens: 120 (1) 100% 120 Diffuse (D) 88% Channel Lens: 120 (1) 100% 20 (2) 100% 40 (4) 100% 120 Diffused (D) 88%
Wide (W) 100%
Photometrics
ria:a:g Criter
.36
=
g
.3
n
r
.1.26
g
.1
Optics for Common Applications
Channel Lens
Aisle Distribution
20° Full Beam Angle
Narrow Distribution 40° Full Beam Angle
VA: 0° 10° 20° 30° 40°
Wide Distribution
“Bat Wing”
VA: 0° 10° 20° 30° 40°
90°
80°
70°
60°
50°
90°
80°
70°
60°
50°
90°
80°
70°
60°
50°
VA: 0° 10° 20° 30° 40°
Standard Distribution
120° Full Beam Angle and 120° Diffuse
90°
80°
70°
60°
50°
VA: 0° 10° 20° 30° 40°
Wrap Lens
Standard Distribution
120° Full Beam Angle and 120° Diffuse
VA: 0° 10° 20° 30° 40°
90°
80°
70°
60°
50°
Mounting & Accessories
Linear Surface Mount
(ALM1-Series)
MOUNTING OPTIONS IMAGE ORDER LOGIC CODE
Standard Surface Mount
Available with all fixture configurations
Lighting
Fasten to ceiling with appropriate hardware
ST = Standard
Installation
See Installation Guide for details
Ceiling and Wall Mounting
See Installation Guide for mounting details.
Ceiling Mount
N/A
Wall Mount
N/A
Product Dimensions
Linear Surface Mount Lighting (ALM1
-Series)
2ft. & 4ft. Channel and Wrap Lens
5.2”
3.3”
End View
3.3”
Top View
24" or 48”
Side View
5.2”
Max. Weight: 15 lbs.
GE Lighting 1-888-MY-GE-LED (1 - 888 - 69 - 43 - 533) www.gelighting.com
Albeo and the GE brand and logo are trademarks of the General Electric Company. © 2014 GE. Information provided is subject to change without notice. All
values are design or typical values when measured under laboratory conditions.
ALB009 070814
Loading...