GE air conditioner Accessories Catalog

GE AIR CONDITIONER

ACCESSORIES

Split System/Built-In/Window/Zoneline®Models

We bring good things to life.

SPLIT SYSTEM UNITS

RAAS12 Replacement Filters for 9,000 and 12,000 Btu/Hr Units

RAAS18 Replacement Filters Sets for 18,000 Btu/Hr Units

RAKREMC Replacement Remote Control for Air Conditioners
RAKREMH Replacement Remote Control for Heat Pump Air Conditioner Units

TUS1542, TUS2542, TUS1553, TUS2553 Tube Kits

A removable and washable original equipment filter
that improves air quality. Frequent filter maintenance
improves efficiency and increases life expectancy of
the unit. Order individually or by box of 20.

Also available as service part number WJ85X10011

A pair of original equipment filters which are removable
and washable that improve air quality. Frequent filter
maintenance improves efficiency and increases life
expectancy of the unit. Order by pairs or by box of 20 pairs.

Also available as service part number WJ85X10009

A wireless remote control allowing operation of the air
conditioner from up to 23 feet. Features include air
circulation, nighttime/sleep operation, temperature
and humidity. In addition, the Auto Operation mode
automatically sets the temperature and fan speeds,
based on room temperature. The Dehumidify mode
automatically sets the cooling fan at a low speed to
remove moisture and to increase comfort. The liquid
crystal display on the remote indicates mode of
operation, time and temperature (C or F).

RAKREMC is also available as service part number
WJ26X10011
RAKREMH is also available as service part number
WJ26X10010

Each kit includes pre-flared, insulated copper
interconnecting tubing (15 foot lengths for models
TUS1542 and TUS1553, and 25 foot lengths for models
TUS2542 and TUS2553), 30 feet of 18-4 gauge
interconnecting wiring cable, plastic sleeve (81⁄4” x 23⁄4”
Dia.) and 12 wire ties.

TUS1542 and TUS2542 are used on GE Split System
Models: AS1CD09AA0, ASOCD09AA0, AS1CD12AA0,
ASOCD12AA0, AS1RD09AA0, AS0RD09AA0,
AS1RD12AA0, and AS0RD12AA0.

TUS1553 and TUS2553 are used on GE Split System
models: AS1CD18DA0, AS0CD18DA0, AS1RD18DA0
and AS0RD18DA0.

Note: Be sure to use the correct tubing kit. Model numbers are
printed on the nameplates located on the side of the indoor and
outdoor units.

RAD4A1 Drain Kit

Internal/External Drain Kit
Drain kit for use on “J” series wall cases. For more
positive control of condensate water, the RAD4A1 drain
kit routes condensate to the exterior or to the interior
of the building through the wall case. Suitable provision
(field applied) should be made to connect the drain
tube to a drain system in the building. Drain tube
assembly is 1/2” O.D. copper.

NOTE: The RAG14E exterior grille is NOT compatible
with the RAD4A1 EXTERNAL drain tube. Use of this
grille would require the use of the INTERNAL TUBE
configuration to drain the unit.

RAK65A1 Window Installation Kit for “J” Series Built-In Units

Adapts built-in wall case for window installation. (This
kit is included in “J” series units designed for window
installation.) Window opening width – 26-7/8" to 40".
Window opening height – 16-3/8" minimum.

RAK7 Support Bracket for Large Chassis

Optional support brackets for large chassis
window models.

WINDOW UNITS

BUILT-IN UNITS

RAB46 Standard Wall Case for “J” Chassis Built-In Unit

Solid-sided wall case fabricated of galvanized steel with
baked enamel (beige) finish. Welded areas are coated
with a sealing compound to help resist rust and corrosion.
Polymer gasket surrounds opening to assure tight weather
seal. Aluminum grille (RAG13) is included. Panels on
interior and between case and grille provide weather
protection prior to installation of chassis.

RAB47/48 Tenant Option Wall Cases for “J” Chassis

When the air conditioner is offered as a tenant option,
these wall cases provide protection against outside
elements.
RAB47 – includes wall case, exterior grille, weather
panel and steel closure panel.
RAB48 – includes wall case, exterior grille, insulated
steel closure panels.

RAG13 Stamped Aluminum Exterior Grille “J” Series

Used to replace exterior grille on old “J” wall case to
maximize efficiency and capacity of new chassis. The
grille is included with new wall cases RAB46, 47, or 48.

RAG14E Architectural Louvered Exterior Grille for “J” Series

Extruded aluminum grille for application with RAB46,
47, or 48.

NOTE: The RAG14E exterior grille is NOT compatible
with the RAD4A1 EXTERNAL drain tube. Use of this
grille would require the use of the INTERNAL TUBE
configuration to drain the unit.

BUILT-IN UNITS

RAF622 Room Side Grille for Rounded Front “J” Chassis Units

Used as replacement grille for rounded front “J”
chassis units. (Not for use with high mount units).

BUILT-IN UNITS

RAK690 Architectural Louver Grille Adapter for “J” Chassis Units

Permits most existing architectural louvered grilles to be
used with sloped front or rounded front “J” chassis units.
Kit consists of two wire mesh screen sections, clips to
attach screen to existing wall case, and two air deflectors
to be mounted to new chassis.

RAK1072 Hotpoint Chassis Sleeve Adapter

Kit adapts Hotpoint ACXB 10 and ACXB 11 wall case
(used with ACTB chassis) to the sloped front or rounded
front “J” chassis. Existing case dimensions are 25-3/4" W,
16-7/8" H, 18-5/8" D. All needed gaskets and hardware,
including the outdoor grille, are included.

RAK1082 Whirlpool Sleeve Adapter

Kit adapts Whirlpool Type 23W wall case for installation
of the sloped front or rounded front “J” model chassis.
The Whirlpool case dimensions are 25-7/8" W, 16-1/2"
H, 23-1/8" D.

RAK1102 RAB30 (F Model Sleeve) Adapter

Kit adapts RAB30 wall case for installation of the sloped
front or rounded front “J” model chassis. The RAB30
case dimensions are 26" W, 18" H, 24"D.

RAK56A100 RAB13, 14 and 15 Sleeve Adapter

This gasket kit allows replacement of ACLB or RCL
units (which used the RAB13, 14, or 15 wall case) with
the “J” model chassis. These cases have gaskets
approximately 1/3 of the way back from the front. In
addition to the kit, order either RAG13 (stamped) or
RAG14E (architectural) grille or use RAK690 kit to allow
new chassis to be used with existing architectural grille.

BUILT-IN UNITS

RAK126 Westinghouse Sleeve Adapter

Kit adapts Westinghouse wall case (2626D73H01) for
installation of sloped front “J” chassis. The
Westinghouse case dimensions are 25-7/8" W,
15-7/16" H, 16" D.

In addition to the kit, order either RAG13 (stamped
grille) or RAG14E (architectural grille) to replace the
existing outdoor grille.

RAK123A64 Fedders Sleeve Adapter

Kit adapts Fedders “A” wall case for installation of the “J”
wall case (includes outdoor grille) and “J” model
chassis. Existing Fedders wall case dimensions are
27" W, 16-3/4" H, 16-3/4" D.

Kit consists of four gaskets which are applied to the wall
case to assure a tight weather seal between the two cases.