GE AHR05 Owner’s Manual & Installation Instructions
GEAppliances.com
Room
Safety Instructions . . . . . . . . . . . . . 2, 3
Operating Instructions
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Care and Cleaning
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Outdoor Coils . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation Instructions . . . . . . 6–10
Troubleshooting Tips . . . . . . . . . . . .11
Normal Operating Sounds . . . . . . . . . . . .11
Consumer Support
Consumer Support . . . . . . . . . . . . . . . . . . .14
Warranty for Customers
in the U.S.A. . . . . . . . . . . . . . . . . . . . . . . . . . .13
Owner’s Manual and
Installation Instructions
AHR05
Write the model and serial numbers here:
Model # _________________________
Serial # __________________________
Find these numbers on a label on the side of
the air conditioner.
Air Conditioners
In Canada, contact us at:
www.GEAppliances.ca
49-7689 12-10 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
SAFETY PRECAUTIONS
n Use this appliance only for its intended
purpose as described in this Owner’s
Manual.
n This air conditioner must be properly
installed in accordance with the Installation
Instructions before it is used.
n Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly
and pull straight out from the receptacle.
n Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply
cord obtained from the manufacturer and
not repaired. Do not use a cord that shows
cracks or abrasion damage along its length
or at either the plug or connector end.
n Turn the unit OFF and unplug your air
conditioner before cleaning.
n GE does not support any servicing of the
air conditioner. We strongly recommend
that you do not attempt to service the air
conditioner yourself.
n For your safety…do not store or use
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
n All air conditioners contain refrigerants,
which under federal law must be removed
prior to product disposal. If you are getting
rid of an old product with refrigerants, check
with the company handling disposal about
what to do.
n If the receptacle does not match the plug,
the receptacle must be changed out by a
qualified electrician.
n These R410A air conditioning systems
require contractors and technicians to
use tools, equipment and safety standards
approved for use with this refrigerant.
DO NOT use equipment certified for
R22 refrigerant only.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
DO NOT use an adapter plug with this
appliance.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance.
Power cord includes a current interrupter device.
A test and reset button is provided on the plug
case. The device should be tested on a periodic
basis by first pressing the TEST button and
then the RESET button while plugged into the
outlet. If the TEST button does not trip or if the
RESET button will not stay engaged, discontinue
2
use of the air conditioner and contact a qualified
service technician.
Have the wall outlet and circuit checked by
a qualified electrician to make sure the outlet
is properly grounded.
Where a 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded
3-prong wall outlet.
The air conditioner should always be plugged
into its own individual electrical outlet which has
a voltage rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.
GEAppliances.com
WARNING!
USE OF EXTENSION CORDS
RISK OF FIRE. Could cause serious injury or
death.
• DO NOT use an extension cord with this
Window Air Conditioner.
• DO NOT use surge protectors or multi-outlet
adaptors with this Window Air Conditioner.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY
SAVE THESE INSTRUCTIONS
.
3
About the controls on the air conditioner
Features and appearance will vary.
Speed
Low
Cool
Fan Only
High
Cool
Power
Wait 3 Mins. Before
Restarting
Controls
Temperature Control
Setting determines how much cooling is
provided. High Cool provides the most cooling
and Low Cool provides the least.
Fan Only turn off the cooling.
NOTE: If you move the Temperature control
from a cool setting to OFF or to a fan setting,
wait at least 3 minutes before switching back to
a cool setting.
Hi
On
w
Lo
Off
Fan Speed
The fan speed button can be set on HI or LOW.
In both cooling mode and fan only mode.
Power
Turns the unit on or off.
Cooling Descriptions
For Normal Cooling—Select High Cool or Low
Cool.
For Maximum Cooling—Select High Cool with the
FAN SPEED set to HI.
For Quieter and Nighttime Cooling—Select Low
Cool with the FAN SPEED set to LOW.
Air Direction
Use the lever to adjust the air direction left and right
only.
lever is in middle
4
Care and Cleaning the air conditioner GEAppliances.com
Grille and Case
Turn the air conditioner off and remove the plug from
the wall outlet before cleaning.
To clean, use water and a mild detergent. Do not use
bleach or abrasives.
Air Filter
The air filter behind the front grille should be checked
and cleaned at least every 30 days or
more often if necessary.
To remove:
Open the inlet grille by pulling downward on the tabs
at the top upper corners of the inlet grille until the
grille is in a 45º position. Remove the filter.
Clean the filter with warm, soapy water. Rinse and let
the filter dry before replacing it. Do not clean the filter
in a dishwasher.
CAUTION: DO NOT operate the air
conditioner without a filter because dirt and lint will
clog it and reduce performance.
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly. If they are clogged with
dirt or soot, they may be professionally cleaned.
5
Installation
Air Conditioner
Instructions
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com
In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely
and carefully.
•
IMPORTANT — Save these instructions
for local inspector’s use.
•
IMPORTANT — Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
• Completion time – Approximately 1 hour
• We recommend that two people install
this product.
• Proper installation is the responsibility
of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
• You MUST use all supplied parts and use proper
installation procedures as described in these
instructions when installing this air conditioner.
CAUTION:
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Do not change the plug on the power cord of this air
conditioner.
Aluminum house wiring may present special
problems—consult a qualified electrician.
TOOLS YOU WILL NEED
Phillips head screwdriver
Drill and 1/8” drill bit
ELECTRICAL REQUIREMENTS
Some models require a 115/120-volt AC,
60-Hz grounded outlet protected with a
15-amp time-delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall outlet you
plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
Some models require 230/208-volt AC,
protected with a time-delay fuse or circuit
breaker. These models should be installed on
their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
Pencil
Level
Power cord includes a current interrupter
device. A test and reset button is provided on the
plug case. The device should be tested on a periodic
basis by first pressing the TEST button and then the
RESET button while plugged into the outlet. If the
TEST button does not trip or if the RESET button will not
stay engaged, discontinue use of the air conditioner
and contact a qualified service technician.
6
Ruler or tape measure
Scissors or knife
PARTS INCLUDED
(Appearance may vary)
Top channel
Installation Instructions
Foam seal
Air
conditioner
Type A screws (3)
Side curtains (2)
Type B screws (7)
Side curtains frames (2)
Window lock bracket (3)
7
Installation Instructions
1
WINDOW REQUIREMENTS
•These instructions are for a standard double-hung
window. You will need to modify them for other types
of windows.
•The air conditioner can be installed without the
side curtain if needed to fit in a narrow window.
See the window opening dimensions.
•All supporting parts must be secured
to firm wood, masonry or metal.
•The electrical outlet must be within reach of the
power cord.
•Follow the dimensions in the table and illustration
for your model.
12” 3/8”
23 1/4”- 36”
(With side curtain)
3
PREPARE THE AIR CONDITIONER
Install the top mounting rail with 3 Type A
A
screws from the outside of the case.
Top mounting rail
B
Slide curtain panel into side rails.
2
STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep it
from draining properly.
To adjust for this, attach a piece of wood to the sill.
WOOD PIECES
WIDTH: 2”
LENGTH: Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness, place a
piece of wood on the sill to make it 1/2” higher than
the top of the storm window frame or the vinyl
frame.
Attach securely with nails or screws provided by the
installer.
1/2” higher
than vinyl frame
(on some windows)
1/2” higher
than storm
window
frame
Storm window
frame
Sill
Vinyl frame
Wood
C
Slide left and right side curtain frames into top
and bottom mounting rail. Make sure curtain
snaps into place.
Top left
Bottom mounting rail
Top mounting rail
Top right
8
Installation Instructions
5
PREPARING THE WINDOW FOR
INSTALLATION
Measure the width of the window opening and
A
mark the center line on the inside windowsill.
Width of window opening
Center line
B
Install the window lock bracket behind the
inner windowsill, with the short side of window
lock. Use 2 type B screws provided.
The window lock bracket helps hold unit
securely in place. Be sure to place window
lock bracket edge flush against back or inner
sill.
Type B screws
Inner sill
Outer sill
Window lock
brackets
Center line
6
INSTALL THE AIR CONDITIONER
IN THE WINDOW
A
Set the air conditioner in the window so that
is centered. Place the air conditioner so that
front edge of the bottom mounting rail is
against the back edge of the sill.
Window frame
Top channel
About 1/4”
Bottom guide
Window lock
bracket
Bring the window down so that the front
B
edge of the top mounting is in front of the
window. Make sure that that air conditioner
is level or tilting slightly to the outside.
Short side
7.5”
7.5”
Type B screws
C
Extend the curtain panels until they fill the
window. Mark the location of the holes in
each corner. Use the drill and 1/8” drill bit to
drill pilot holes. Use 4 type B screws to to
secure the side panels in place.
9
Loading...