GE AEW05, AEW08, AEW06, AET05 User Manual

Safety Instructions . . . . . . . . .2, 3

Operating Instructions

Control Knob Models . . . . . . .6, 7
Touch Pad Models . . . . . . . . . .4, 5

Care and Cleaning

Air Filter . . . . . . . . . . . . . . . . . . .7
Outdoor Coils . . . . . . . . . . . . . . .7
Installation Instructions . . .8–11
Normal Operating Sounds . . . .12

Consumer Support

Consumer Support . . . . . . . . . .14
Warranty . . . . . . . . . . . . . . . . . .13
49-7514-1 11-05 JR
AET05 AEW05 AEW06 AEW08
Owner’s Manual and
Installation Instructions
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label on the side of the air conditioner.
Air Conditioners
ge.com
Room
Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

2
IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock or personal injury.
Use this appliance only for its intended
purpose as described in this Owner’s Manual.
This air conditioner must be properly
installed in accordance with the Installation Instructions before it is used.
Never unplug your air conditioner by pulling
on the power cord. Always grip plug firmly and pull straight out from the receptacle.
Replace immediately all electric service
cords that have become frayed or otherwise damaged. A damaged power supply cord must be replaced with a new power supply cord obtained from the manufacturer and not repaired. Do not use a cord that shows cracks or abrasion damage along its length or at either the plug or connector end.
Turn the unit OFF and unplug your air
conditioner before cleaning.
GE does not support any servicing of the air
conditioner. We strongly recommend that you do not attempt to service the air conditioner yourself.
For your safety…do not store or use
combustible materials, gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance.
All air conditioners contain refrigerants,
which under federal law must be removed prior to product disposal. If you are getting rid of an old product with refrigerants, check with the company handling disposal about what to do.
SAFETY PRECAUTIONS
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.
Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
The air conditioner should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
See the Installation Instructions, Electrical Requirements section for specific electrical connection requirements.
HOW TO CONNECT ELECTRICITY
3
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions
ge.com
WARNING!
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed, 14 gauge, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 125 volts.
USE OF EXTENSION CORDS—115-Volt models only
Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.
However, if you must use an adapter, where local codes permit, a temporary connection may be made to a properly grounded 2-prong wall outlet by use of a UL-listed adapter available at most local hardware stores.
The larger slot in the adapter must be aligned with the larger slot in the wall outlet to provide proper polarity in the connection of the power cord.
When disconnecting the power cord from the adapter, always hold the adapter in place with one hand while pulling the power cord plug with the other hand. If this is not done, the adapter ground terminal is very likely to break with repeated use.
If the adapter ground terminal breaks, DO NOT USE the air conditioner until a proper ground has been established.
Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the cover screw is metal, and not insulated, and the wall outlet is grounded through the house wiring. You should have the circuit checked by a qualified electrician to make sure the outlet is properly grounded.
USE OF ADAPTER PLUGS—115-Volt models only
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
4
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
About the controls on the air conditioner—models with touch pads.
Controls
Power Pad
Turns air conditioner on and off. When turned on, the display will show the room temperature.
Display
Shows the room temperature or time remaining on the Delay timer. Shows the Set temperature while setting the temperature in Cool or Energy Saver modes. The Set light will turn on while setting.
NOTE: The display will change to show the room temperature after settings have been made. To recall the Set temperature, press the
Temp Increase or Decrease pads.
Temp Increase /Decrease Pads
Use to set temperature when in Cool or Energy Saver mode. The Set light will turn on while
setting.
Delay Timer Increase (+) /Decrease ▼ (–) Pads
Each touch of the Increase / Decrease pads on the unit or the Increase
+ / Decrease
pads on the remote control will set the delay time when using the Delay 1–24hr timer ( ). The Set light will turn on while setting.
Fan Speed Pads
Use to set the fan speed to Low, Med, High or Auto on the unit. NOTE: On the remote control, use the fan speed Increase
+ /
Decrease pads to set the fan speeds to Low, Med or High. Use the Auto pad to turn Auto
fan on.
Mode Pad
Use to set the air conditioner to Cool, Energy Saver or Fan Only mode.
Delay Pads
Delay ON—When the air conditioner is off, it
can be set to automatically come on in 1 to 24 hours at its previous mode and fan settings.
Delay OFF—When the air conditioner is on, it can be set to automatically turn off in 1 to 24 hours.
How to set:
Press the Delay 1–24hr pad on the unit or the pad on the remote control. Each touch of the Increase / Decrease pads on the unit or the Increase + / Decrease pads on the remote control will set the timer in 1-hour intervals. The Set light will turn on while setting.
To review the remaining time on the Delay 1–24hr timer, press the Delay 1–24hr pad on the unit or the pad on the remote control. Use the Increase / Decrease pads on the unit or the Increase
+ / Decrease
pads on the
remote control to set a new time if desired.
To cancel the timer, press the Delay 1–24hr pad until the light on the Delay 1–24hr pad goes off.
Lights next to the touch pads on the air conditioner control panel indicate the selected settings.
Delay 1–24hr
Delay timer Decrease
Mode select
Fan speed Decrease
Temperature set Increase and Decrease
Remote Control
Delay timer Increase
Auto Fan on/off
Fan speed Increase
Unit power on/off
The display always shows the room temperature except when setting the Set temperature or the Delay timer.
Air Conditioner Controls
Light indicates the delay timer is set.
Light indicates the unit is in the temperature or delay time Set mode.
Delay
M
o
n
a
F
d
-
e
Power
Temp
o
t
u
A
F
a
n
+
5
To ensure proper operation, aim the remote
control at the signal receiver on the air conditioner.
The remote control signal has a range of
up to 20 feet.
Make sure nothing is between the air conditioner
and the remote control that could block the signal.
Make sure batteries are fresh and installed
correctly as indicated on the remote control.
Remote Control
ge.com
Cool Mode
Use the Cool mode at Low, Med, High or Auto Fan Speed for cooling. Use the Temperature Increase ▲ / Decrease pads to set the desired temperature
between 64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Set the thermostat at a higher number and the indoor air will become warmer.
NOTE: If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and High or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode and High fan with a lower set temperature.
For Quieter & Nighttime Cooling—Select the Cool mode and Low fan with a middle set
temperature.
Fan Only Mode
Use the Fan Only Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan only settings do not provide cooling, a Set temperature cannot be entered. The room temperature will appear in the display.
NOTE: Auto Fan Speed cannot be used when in the Fan Only Mode.
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
Energy Saver Mode
Controls the fan.
ON—The fan will cycle on and off with the compressor. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. NOTE: The fan may continue to run
for a short time after the compressor cycles off.
OFF—The fan runs all the time, while the compressor cycles on and off.
In the case of a power outage or interruption, the unit will automatically re-start in the settings last used after the power is restored. If the Delay 1–24hr
feature was set, it will resume countdown. You may need to set a new time if desired.
Power Outage Recovery Feature
Set to Auto fan speed for the fan speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature.
If the room needs more cooling, the fan speed will automatically increase. If the room needs less cooling, the fan speed will automatically decrease.
NOTE: Auto Fan Speed cannot be used when in the Fan Only Mode.
Auto Fan Speed
About the controls on the air conditioner—models with control knobs.
Features and appearance will vary.
Controls
Mode Control
High Cool, Med Cool and Low Cool
provide cooling with different fan speeds.
Fan settings provide air circulation and filtering without cooling.
NOTE: If you move the mode control from a cool setting to OFF or to a fan setting, wait at least 3 minutes before switching back to a cool setting.
Cooling Descriptions
For Normal Cooling—Select High Cool or Med Cool
with the TEMPERATURE control at midpoint.
For Maximum Cooling—Select High Cool with the TEMPERATURE control at the highest number available on your knob.
For Quieter & Nighttime Cooling—Select Low Cool with the TEMPERATURE control at midpoint.
TEMP Control
The TEMP control is used to maintain the room temperature. The compressor will cycle on and off to keep the room at the same level of comfort. When you turn the knob to a higher number, the indoor air will become cooler. Turn the knob to a lower number and the indoor air will become warmer.
MODE CONTROL TEMPERATURE CONTROL
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
6
MODE
High Cool
Med Cool
Low
Cool
OFF
High
Fan
Low
Fan
Coolest
6
TEMP
7
5
4
1
2
3
Remove the battery cover by sliding it according to the arrow direction.
Insert new batteries, making sure that the (+) and (–) of battery are installed correctly.
Reattach the cover by sliding it back into position.
NOTES:
Use 2 “AAA” (1.5 volt) alkaline batteries. Do not
use rechargeable batteries.
Remove the batteries from the remote control if
the system is not going to be used for a long time.
3
2
1
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
7
Air Direction
Use the lever to adjust the air direction left and right only.
ge.com
Additional important information.

Air Filter

The air filter behind the front grille should be checked and cleaned at least every 30 days or more often if necessary.
To remove:
Push on one side of the filter edge and pull it out the other side.
Clean the filter with warm, soapy water. Rinse and let the filter dry before replacing it. Do not clean the filter in a dishwasher.
CAUTION: DO NOT operate the air
conditioner without a filter because dirt and lint will clog it and reduce performance.

Outdoor Coils

The coils on the outdoor side of the air conditioner should be checked regularly. If they are clogged with dirt or soot, they may be professionally cleaned.
Turn the air conditioner off and remove the plug from the wall outlet before cleaning.
To clean, use water and a mild detergent. Do not use bleach or abrasives.
Grille and Case
How to Insert the Batteries in the Remote Control
Care and cleaning of the air conditioner.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT — Save these
instructions for local inspector’s use.
IMPORTANT — Observe all
governing codes and ordinances.
Note to Installer – Be sure to leave these instructions with the Consumer.
Note to Consumer – Keep these instructions for future reference.
Skill level – Installation of this appliance requires basic mechanical skills.
Completion time – Approximately 1 hour
We recommend that two people install
this product.
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under the Warranty.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
Installation
Air Conditioner
Instructions
Some models require a 115/120-volt a.c., 60 Hz grounded outlet protected with a 15-amp time delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility of electric shock hazard. If the wall outlet you plan to use is only a 2-prong outlet, it is your responsibility to have it replaced with a properly grounded 3-prong wall outlet.
Some models require 230/208-volt a.c., protected with a time delay fuse or circuit breaker. These models should be installed on their own single branch circuit for best performance and to prevent overloading house or apartment wiring circuits, which could cause a possible fire hazard from overheating wires.
ELECTRICAL REQUIREMENTS
CAUTION:
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Do not change the plug on the power cord of this air conditioner.
Aluminum house wiring may present special problems—consult a qualified electrician.
8
TOOLS YOU WILL NEED
Phillips head screwdriver
Ruler or tape measurePencil
Level
Scissors or knife
Flat-blade screwdriver
Power cord includes a current interrupter device. A test and reset button is provided on the plug case. The device should be tested on a periodic basis by first pressing the TEST button and then the RESET button. If the TEST button does not trip or if the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.
9
Installation Instructions
Type A (6)
Top mounting rail
Right
accordion
panel
Foam top
window gasket
Window
sash seal
Left
accordion
panel
Type B (2) Type C (5)
Air
conditioner
Window locking
bracket (1)
PARTS INCLUDED
(Appearance may vary)
Installation Instructions
WINDOW REQUIREMENTS
These instructions are for a standard double-hung window. You will need to modify them for other types of windows.
The air conditioner can be installed without the accordion panels if needed to fit in a narrow window. See the window opening dimensions.
All supporting parts must be secured to firm wood, masonry or metal.
The electrical outlet must be within reach of the power cord.
Follow the dimensions in the table and illustration for your model.
Models A B C
AET05, AEW05 13 1/4″ min. 22″–38″ 18 1/4″ min.
AEW06, AEW08 14 1/2″ min. 23″–38″ 19″ min.
1
A
(With accordion panels)
(Without accordion panels)
STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air conditioner to tilt toward the outside, and will keep it from draining properly. To adjust for this, attach a piece of wood to the stool.
WOOD PIECES– WIDTH: 2 LENGTH: Long enough to fit inside the
window frame. THICKNESS: To determine the thickness,
place a piece of wood on the stool to make it 1/2higher than the top of the storm window frame.
Attach securely with nails or screws provided by the installer.
1/2higher than frame
Storm window frame
Wood
Stool
2
10
PREPARE THE AIR CONDITIONER
Install the top mounting rail with 2 Type B screws from the outside of the case.
Slide the left and right accordion panels into the top and bottom mounting rails.
3
A
B
Top mounting rail
Bottom mounting rail
Top left
Top right
B
C
11
Installation Instructions
PREPARE THE AIR CONDITIONER (cont.)
Attach the accordion panels to the case using 3 Type A screws on each side.
3
INSTALL THE AIR CONDITIONER IN THE WINDOW
Place the air conditioner on the stool with the bottom mounting rail against its back edge. Center it and close the window securely behind the top mounting rail. It should be level or slightly tilted to the outside. Use a level; about a 1/3 bubble will be the correct case slant to the outside.
Extend the left and right accordion panels to the vertical window sashes and attach, through the holes in the panels, with 4 Type C screws, as appropriate.
5
A
B
INSTALL A SUPPORT BRACKET AND THE FOAM TOP WINDOW GASKET
Attach the support bracket with one Type C screw.
Cut the foam top window gasket to the window width.
Stuff the foam between the glass and the window to prevent air and insects from getting into the room.
6
A
B
C
Type C screws
or
or
PREPARE THE WINDOW
Cut the window sash seal to the proper length. Peel off the backing and attach the seal to the underside of the window sash.
4
C
Type A screws
Top mounting rail
Bottom mounting rail
Accordion panel
BACK
Troubleshooting Tips.

Consumer Support Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions
12

Normal Operating Sounds

You may hear a pinging noise caused by water
being picked up and thrown against the condenser on rainy days or when the humidity is high. This design feature helps remove moisture and improve efficiency.
You may hear the thermostat click when the
compressor cycles on and off.
Water will collect in the base pan during
high humidity or on rainy days. The water may overflow and drip from the outdoor side of the unit.
The fan may run even when the compressor
does not.
Problem Possible Causes What To Do
Air conditioner The air conditioner Make sure the air conditioner plug is pushed does not start is unplugged. completely into the outlet.
The fuse is blown/circuit Check the house fuse/circuit breaker box and replace breaker is tripped. the fuse or reset the breaker.
Power failure. The unit will automatically re-start in the settings last
used after the power is restored.
There is a protective time delay (approximately 3 minutes) to prevent tripping of the compressor overload. For this reason, the unit may not start normal cooling for 3 minutes after it is turned back on.
The current interrupter Press the RESET button located on the power cord plug. device is tripped.
If the RESET button will not stay engaged, discontinue use of the air conditioner and contact a qualified service technician.
Air conditioner does Airflow is restricted. Make sure there are no curtains, blinds or furniture not cool as it should blocking the front of the air conditioner.
The temp control may On models with touch pads: In the Cool mode, press the not be set correctly. Decrease pad.
• On models with control knobs, turn the temperature knob to a higher number.
The air filter is dirty. Clean the filter at least every 30 days.
See the Operating Instructions section.
The room may have been hot. When the air conditioner is first turned on, you need
to allow time for the room to cool down.
Cold air is escaping. Check for open furnace registers and cold air returns.
Cooling coils have iced up. See “Air conditioner freezing up” below.
Air conditioner Ice blocks the air flow On models with control knobs, set the mode control at freezing up and stops the air conditioner High Fan or High Cool with the Temp at 1 or 2.
from cooling the room.
• On models with touch pads, set the controls at High Fan or High Cool and set the thermostat to a higher temperature.
The remote control The batteries are inserted Check the position of the batteries. They should be is not working incorrectly. inserted in the opposite (+) and (–) direction.
The batteries may be dead. Replace the batteries.
Water drips outside Hot, humid weather. This is normal.
Water drips indoors The air conditioner is not For proper water disposal, make sure the air conditioner
tilted to the outside. slants slightly from the case front to the rear.
Water collects in Moisture removed from air This is normal for a short period in areas with little base pan and drains into base pan. humidity; normal for a longer period in very humid areas.
13
Consumer SupportTroubleshooting TipsOperating Instructions
Safety Instructions
Installation Instructions
GE Air Conditioner Warranty—One Year Limited Warranty.
For The Period Of: We Will Replace:
One Year Replacement unit for any product which fails due to a defect in materials or workmanship.
From the date of the The exchange unit is warranted for the remainder of your product’s original one-year original purchase warranty period.
Customer instruction. This owner’s manual provides
information regarding operating instructions and user controls.
Improper installation. If you have an installation problem,
or if the air conditioner is of improper cooling capacity for the intended use, contact your dealer or installer. You are responsible for providing adequate electrical connecting facilities.
Failure of the product resulting from modifications to
the product or due to unreasonable use including failure to provide reasonable and necessary maintenance.
Replacement of house fuses or resetting of circuit
breakers.
Damage to the product caused by improper power supply
voltage, accident, fire, floods or acts of God.
Incidental or consequential damage caused by possible
defects with this air conditioner.
What Is Not Covered:
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Exclusion of implied warranties: Except where prohibited or restricted by law, there are no warranties, whether express, oral or statutory which extend beyond the description on the face hereof, including specifically the implied warranties of merchantability or fitness for a particular purpose.
Warrantor: General Electric Company. Louisville, KY 40225
Staple your receipt here. Proof of the original purchase date is needed to make a warranty claim.
Properly pack your unit. We recommend using the
original carton and packing materials.
Return the product to the retail location where it
was purchased.
Include in the package a copy of the sales receipt or other
evidence of date of original purchase. Also print your name and address and a description of the defect.
In Order to Make a Warranty Claim:
Printed in China
14
Consumer Support.
GE Appliances Website
ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day, any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals, or even order parts and catalogs on-line. You can also “Ask Our Team of Experts™” your questions, and so much more...
Real Life Design Studio ge.com
GE supports the Universal Design concept—products, services and environments that can be used by people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Parts and Accessories ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day or by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. GE does not support any servicing of the air conditioner. We strongly recommend that you do not attempt to service the air conditioner yourself.
Contact Us ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park Louisville, KY 40225
Instrucciones de seguridad . . . .2, 3

Instrucciones de operación

Modelos con botones de control 6, 7 Modelos con teclas de toque . . .4, 5

Cuidado y limpieza

Bobinas para exteriores . . . . . . . . . .7
Filtro de aire . . . . . . . . . . . . . . . . . . .7
Instrucciones de instalación . .8–11
Solucionar problemas . . . . . . . . .12
Sonidos de operación normales . .12

Servicio al consumidor

Garantía . . . . . . . . . . . . . . . . . . . . .13
Servicio al consumidor . . . . . . . . .14
49-7514-1 11-05 JR
Escriba los números de modelo y serie aquí:
# de Modelo __________________
# de Serie ____________________
Puede encontrar estos números en una etiqueta en el costado del acondicionador de aire.
AET05 AEW05 AEW06 AEW08
Manual del propietario e
Instrucciones de Instalación
Acondicionadores de Aire
ge.com
2
Servicio al consumidor
Solucionar problemas Operación SeguridadInstalación
INFORMACIÓN IMPORTANTE DE SEGURIDAD. LEA TODAS LAS INSTRUCCIONES ANTES DE USAR.
¡ADVERTENCIA!
Por su seguridad, se debe seguir la información en este manual para minimizar el riesgo de incendios, descargas eléctricas o lesiones personales.
Use este electrodoméstico solamente para
el propósito determinado según se describe en el Manual del propietario.
Este acondicionador de aire debe instalarse
correctamente de acuerdo con las Instrucciones de instalación antes de su uso.
Nunca desenchufe su acondicionador de
aire tirando del cable eléctrico. Siempre agarre firmemente el enchufe y tire de él directamente hacia afuera.
Reemplace inmediatamente todos los cables
eléctricos que se hayan pelado o que se hayan dañado de alguna otra manera. Un cable de corriente dañado no debe repararse, sino que debe ser sustituido por uno nuevo que se adquiera del fabricante. No use un cable eléctrico que muestre evidencias de deterioro, o daños de abrasión en su superficie en alguno de sus extremos.
Apague la unidad y desenchufe su
acondicionador de aire antes de limpiar.
GE no está no apoya que se le proporcione
ningún servicio al acondicionador de aire. Vehementemente recomendamos que usted no intente proporcionar servicio al acondicionador de aire usted mismo.
Por su seguridad…no almacene ni use
materiales combustibles, gasolina u otros vapores o líquidos inflamables en la proximidad de éste o algún otro electrodoméstico.
Todos los acondicionadores de aire
contiene refrigerantes, los que por Ley Federan deben ser removidos antes de desecharlos. Si usted planea deshacerse de algún producto que contenga refrigerantes, póngase en contacto con la compañía que se encarga de recoger su basura para que le indiquen qué hacer.
PRECAUCIONES DE SEGURIDAD
Bajo ninguna circunstancia, corte o remueva la tercera púa (tierra) del cable eléctrico. En pos de la seguridad personal, este electrodoméstico debe siempre conectarse a tierra.
El cable eléctrico de este electrodoméstico está equipado con un enchufe de tres púas (tierra) que combina con un tomacorriente estándar de tres tomas de pared para minimizar la posibilidad de una descarga eléctrica.
El cable de alimentación incluye un dispositivo para interrupción de corriente. Se incluye un botón de prueba y de reinicio en el dispositivo. El dispositivo debe ponerse a prueba periódicamente: primero se presiona el botón de TEST (prueba) y luego RESET (reinicio). Si el botón TEST no se dispara o si el botón RESET no queda enganchado, deje de utilizar el acondicionador de aire y comuníquese con un técnico calificado.
Pida a un técnico que inspeccione el tomacorriente y el circuito para cerciorarse
de que el tomacorriente está conectado a tierra de la manera apropiada.
Donde exista un tomacorriente de dos tomas, es su responsabilidad y obligación personal hacer que dicho tomacorriente sea reemplazado por uno de tres tomas con conexión a tierra.
El acondicionador de aire debería siempre estar conectado a un tomacorriente individual con su circuito de voltaje correspondiente.
Esto proporciona el mayor rendimiento y además evita que los circuitos del resto de la casa se sobrecarguen, lo cual podría causar incendios por el sobrecalentamiento del cableado.
Ver las Instrucciones de instalación, en la sección Requisitos Eléctricos para los requisitos específicos de conexión.
CÓMO CONECTAR LA ELECTRICIDAD
3
Servicio al consumidorSolucionar problemas
Operación
Seguridad
Instalación
ge.com
¡ADVERTENCIA!
Debido al potencial de riesgos de seguridad bajo ciertas condiciones, enérgicamente recomendamos contra el uso de cables de extensión.
Sin embargo, si usted se ve en la necesidad de usar un cable eléctrico de extensión, es absolutamente necesario que el mismo esté listado bajo UL, sea calibre 14, del tipo de 3 tomas con conexión a tierra para electrodomésticos y el índice eléctrico debe ser de 15 amperios (mínimo) y 125 voltios.
USO DE CABLES DE EXTENSIÓN—Modelos de 115 voltios solamente
Debido al potencial de riesgos de seguridad bajo ciertas condiciones, enérgicamente recomendamos contra el uso de enchufes adaptadores.
Sin embargo, si usted se ve en la necesidad de usar un adaptador, donde los códigos legales locales lo permitan, puede hacer una conexión temporal a un interruptor de 2 tomas siempre que se use un tomacorriente listado UL disponible en la mayoría de las ferreterías.
La ranura mayor en el adaptador debe estar alineada con la púa mayor en la pared para proporcionar una polaridad apropiada en la conexión del cable eléctrico.
Cuando se disponga a desconectar el cable eléctrico del adaptador, siempre sostenga el adaptador en su lugar con una mano mientras tira del cable eléctrico con la otra mano. Si no hace esto, la terminal de tierra del adaptador podría romperse después de que este proceso se repita varias veces.
Si se rompe el terminal de conexión a tierra del adaptador, NO USE el acondicionador de aire hasta que la conexión a tierra se haya restablecido.
Unir el terminal de conexión a tierra del adaptador a un tornillo de la cubierta en la pared no conecta a tierra el electrodoméstico apropiadamente a no ser que el tornillo de la cubierta sea metálico y no esté aislado, y el tomacorriente de la casa esté apropiadamente conectado a tierra a través del cableado de la casa. Haga que un técnico calificado inspeccione el circuito de la casa para cerciorarse que está conectado a tierra apropiadamente.
USO DE ENCHUFES ADAPTADORES—Modelos de 115 voltios solamente
LEA Y SIGA ESTAS INSTRUCCIONES DE SEGURIDAD CUIDADOSAMENTE.
GUARDE ESTAS INSTRUCCIONES
4
Acerca de los controles en el acondicionador de aire— modelos con teclas de toque.
Controles
Tecla de Power (Encendido)
Apaga y prende el acondicionador de aire. Al encenderse, la pantalla mostrará la temperatura ambiente.
Pantalla
Muestra la temperatura ambiente o el tiempo restante en el Sincronizador de retardo. Muestra la temperatura Definida al configurar la temperatura en los modos Cool (Frío) o de Energy Saver (Ahorro de energía). La luz de Ajuste se encenderá durante la configuración.
NOTA: la pantalla cambiará para mostrar la temperatura ambiente una vez que se haya realizado la configuración. Para restituir la temperatura Definida, pulse las teclas de Temp
(Temperatura) Aumento o Reducción ▼. Teclas de Temp Aumento /Reducción
Usado para ajustar la temperatura cuando se encuentre en el modo Cool (Frío) o Energy Saver (Ahorro de energía). La luz de Ajuste se encenderá durante la configuración.
Teclas de Sincronizador de retardo Aumento (+) / Reducción ▼ (–) Cada vez que toque las teclas Aumento / Reducción de la unidad o las teclas Aumento + / Reducción – en el control remoto definirá
el tiempo de retardo al utilizar el Delay 1–24hr timer (Sincronizador de retardo 1–24 h) (). La luz de Ajuste se encenderá durante la configuración.
Teclas de Fan Speed (Velocidad del ventilador)
Usado para ajustar la velocidad del ventilador a Low (Bajo), Med (Medio), High (Alto) o Auto (Automática) en la unidad. NOTA: en el control remoto, utilice las teclas Aumento + / Reducción – velocidad de ventilador para ajustar la velocidad del ventilador en Low (Bajo), Med (Medio) o High (Alto). Utilice la tecla Auto para activar el ventilador automático.
Tecla de MODO
Usado para ajustar el acondicionador de aire al modo Cool (Frío), Energy Saver (Ahorro de
energía) o Fan Only (Solo ventilador). Teclas de Delay (Retardo)
Delay ON (ENCENDIDO Retardo)—Cuando
el acondicionador de aire está apagado, puede ajustarse para que se encienda automáticamente dentro de 1 a 24 horas en el modo y configuración de ventilador anterior.
Delay OFF (APAGADO Retardo)—Cuando el acondicionador de aire está encendido, puede ajustarse para que se apague automáticamente dentro de 1 a 24 horas.
Cómo realizar el ajuste:
Pulse la tecla Delay 1–24hr (Retardo 1–24h) en la unidad o en la tecla del control remoto. Cada toque de las teclas Aumento /
Reducción en la unidad o las teclas Aumento + / Reducción – en el control remoto definirá
el temporizador en intervalos de 1 hora. La luz de Ajuste se encenderá durante la configuración.
Para revisar el tiempo restante en el Sincronizador de retardo 1–24 h, pulse la tecla de Delay 1–24hr (Retardo 1–24h) en la unidad o en la tecla del control remoto. Utilice las teclas Aumento / Reducción en la unidad o las teclas Aumento + / Reducción – en el control remoto para definir un nuevo tiempo, si lo desea.
Para cancelar el sincronizador, pulse la tecla Delay 1–24hr (Retardo 1–24h) hasta que la luz
de dicho control se apague.
Servicio al consumidor
Solucionar problemas Operación SeguridadInstalación
1–24 h de retardo
Reducción de sincronizador de retardo
Selección de modo
Reducción de velocidad del ventilador
Aumento y reducción de ajuste de temperatura
Control remoto
Aumento de sincronizador de retardo
Encendido/apagado automático del ventilador
Aumento de velocidad del ventilador
Encendido/apagado de la unidad
Controles del acondicionador de aire
La luz indica que el temporizador de retardo está configurado.
La pantalla muestra siempre la temperatura ambiente, excepto al configurar la temperatura Definida o el Sincronizador de retardo.
Las luces al lado de las teclas de toque en el panel de control del acondicionador de aire indicarán los ajustes seleccionados.
La luz indica que la unidad está en el modo de Ajuste de temperatura o de Tiempo de retardo.
Delay
M
o
n
a
F
d
-
e
Power
Temp
o
t
u
A
F
a
n
+
5
Para garantizar una operación apropiada, oriente
el control remoto hacia el receptor de señal del acondicionador de aire.
El receptor de señal tiene un rango máximo de
20 pies.
Cerciórese de que no haya nada entre el
acondicionador de aire y el control remoto que pueda bloquear la señal.
Cerciórese de que las baterías sean frescas y se
instalen correctamente según se indica en el control remoto.
Control remoto
ge.com
Modo Cool (Frío)
Use el modo Cool (Frío) a Low (Bajo), Med (Medio), High (Alto) o Auto Fan Speed (Velocidad de ventilador automática) para enfriar. Use las teclas de Temperature (Temperatura) Aumento (+) / Reducción
(–) para ajustar a la temperatura deseada entre 64ºF y 86ºF en incrementos de 1ºF.
Se usa un termostato electrónico para mantener la temperatura ambiente. El compresor hará ciclo entre apagado y encendido para mantener la habitación a la temperatura deseada. Ajuste el termostato a un número menor y el aire interno se enfriará más. Si lo ajusta a un número mayor, la temperatura del aire interno se calentará más.
NOTA: si el acondicionador de aire está apagado y se enciende mientras está configurado en un ajuste Cool (Frío) o si se cambia de un ajuste de ventilador a uno de Cool
(Frío), puede que pasen aproximadamente unos 3 minutos hasta que el compresor arranque y comience el enfriamiento.
Descripciones de enfriamiento Para enfriamiento normal—Seleccione el modo
Cool (Frío) y ventilador High (Alto) o Med (Medio)
con una temperatura de ajuste media.
Para enfriamiento máximo—Seleccione el modo Cool (Frío) y ventilador High (Alto) con una
temperatura de ajuste menor.
Para enfriamiento silencioso y enfriamiento nocturno—Seleccione el modo Cool (Frío) y
ventilador Low (Bajo) con una temperatura de ajuste media.
Modo de Fan Only (Solo ventilador)
Use el modo Fan only (Solo ventilador) a velocidad Low (Baja), Med (Media) o High (Alta) para
proporcionar circulación de aire y filtración sin enfriamiento. Debido a que los niveles de ventilador únicamente no proporcionan enfriamiento, no se puede introducir una
temperatura Definida. Aparecerá en pantalla la temperatura ambiente.
NOTA: la Velocidad de ventilador automática no puede utilizarse en el modo Fan only (Solo ventilador).
Energy Saver Mode (Modo de ahorro de energía)
Controla el ventilador. ON (ENCENDIDO)—El ventilador hará un ciclo
de encendido y apagado con el compresor. Este resulta en variaciones mayores en la temperatura de la habitación y en la humedad. Normalmente usado cuando la habitación no está ocupada.
NOTA: puede que el ventilador siga funcionando durante un corto tiempo después de desactivarse el ciclo del compresor.
OFF (APAGADO)—El ventilador funciona todo el tiempo, mientras que el compresor pasa por los ciclos de encendido y apagado.
En caso de la pérdida de la energía o interrupción, la unidad reiniciará automáticamente en las funciones de la última vez que fue usado una vez la energía sea restablecida. Si la función del
Delay 1–24hr (Retardo 1–24h) estaba definido, continuará la cuenta regresiva. Es posible que usted necesite ajustar un tiempo nuevo si así lo desea.
Función de recuperación de pérdida de energía
Servicio al consumidor
Solucionar problemasOperaciónSeguridad Instalación
Indique la opción en Velocidad de ventilador automática para definir automáticamente la velocidad necesaria para proporcionar una configuración de comodidad óptima con la temperatura elegida.
Si la habitación necesita más enfriamiento, la velocidad del ventilador aumentará
automáticamente. Si la habitación necesita menos enfriamiento, la velocidad del ventilador descenderá automáticamente.
NOTA: la Velocidad de ventilador automática no puede utilizarse en el modo Fan only (Solo ventilador).
Velocidad de ventilador automática
6
Servicio al consumidor
Solucionar problemas Operación SeguridadInstalación
Acerca de los controles en el acondicionador de aire—modelos con botones de control.
Las funciones y el aspecto pueden variar.
Controles
Control de modo
High Cool (Frío Alto), Med Cool (Frío Medio) y Low Cool (Frío Bajo)
proporcionan enfriamiento con diferentes velocidades del ventilador.
Los ajustes del ventilador proporcionan circulación de aire y filtración sin enfriar.
NOTA: Si usted mueve el control de modo de un nivel frío a OFF (APAGADO) o a un nivel de ventilador, espere por lo menos 3 minutos antes de cambiar otra vez a un nivel de enfriamiento.
Descripciones de enfriamiento
Para enfriamiento normal—Seleccione High Cool (Frío Alto) o Med Cool (Frío Medio) con el control
de TEMPERATURA en el medio.
Para enfriamiento máximo—Seleccione High Cool (Frío Alto) con el control de TEMPERATURA en
el número mayor disponible en su teclado. Para enfriamiento silencioso durante la noche
Seleccione Low Cool (Frío Bajo) con el control de TEMPERATURA en el nivel medio.
Control de TEMP
El control de TEMP es usado para mantener la temperatura ambiente. El compresor hará ciclo entre encendido y apagado para mantener el mismo nivel de temperatura en la habitación. Cuando usted gira el botón hacia un número mayor, el aire interno se enfriará más. Si lo ajusta a un número menor, la temperatura del aire interno se calentará más.
CONTROL DE MODO
CONTROL DE TEMPERATURA
MODE
High
Cool
Med Cool
Low
Cool
OFF
High
Fan
Low
Fan
Coolest
7
6
5
4
1
2
3
TEMP
Retire la cubierta de la pila deslizándola de acuerdo con la dirección de la flecha.
Inserte pilas nuevas cerciorándose de que los polos positivos (+) y negativos (–) están orientados correctamente.
Coloque la cubierta otra vez deslizándola en su lugar.
NOTAS:
Use 2 pilas alcalinas “AAA” de 1,5 voltios.
No use pilas recargables.
Retire las pilas del control remoto si no va
a usar el sistema por un período prolongado.
3
2
1
7
Servicio al consumidorSolucionar problemas
Operación
Seguridad
Instalación
Cuidado y limpieza del acondicionador de aire.
Dirección del aire
Use la palanca para ajustar la dirección del aire hacia la izquierda y la derecha solamente.
ge.com
Información importante adicionale.

Filtro de aire

El filtro de aire detrás de la rejilla frontal debe inspeccionarse y limpiarse por lo menos cada 30 días o más a menudo si fuese necesario.
Para retirarlo:
Empuje en un lado del borde del filtro y tirelo del otro lado.
Limpie el filtro con agua tibia y jabón. Enjuáguelo y permita que se seque antes de colocarlo otra vez en su lugar. No lave el filtro en un lavavajillas.
PRECAUCIÓN:NO OPERE el
acondicionador de aire sin el filtro debido a que la suciedad y las pelusas lo obstruirán y reducirán su rendimiento.

Bobinas para exteriores

Se deben inspeccionar con frecuencia las bobinas en el lado exterior del acondicionador de aire. Si las mismas están obstruidas con suciedad u hollín, podrían limpiarse profesionalmente.
Apague el acondicionador de aire y retire el enchufe del tomacorriente de la pared antes de limpiar.
Para limpiar, use agua y un detergente suave. No use cloro o materiales abrasivos.
Rejilla y caja
Cómo insertar las pilas en el control remoto
8
¿Preguntas? Llame 800.GE.CARES (800.432.2737) o Visite nuestra página en la red en: ge.com
Instrucciones
Acondicionador
de instalación
de aire
Algunos modelos requieren tomacorrientes de 115/120 voltios de corriente alterna y 60 Hz conectados a tierra, protegidos con un fusible de dilatación de tiempo de 15 amperios o un cortacircuitos.
El enchufe de tres púas con conexión a tierra minimiza la posibilidad de descargas eléctricas. Si el tomacorriente de la pared que usted planea usar solamente tiene 2 tomas, es su responsabilidad hacer que un técnico lo reemplace por uno de tres tomas con conexión a tierra.
Algunos modelos requieren 230/208 voltios, de corriente alterna, protegidos por un fusible de dilatación de tiempo o un cortacircuitos. Estos modelos deberían instalarse en un ramal exclusivo del circuito para un rendimiento más notable y para prevenir sobrecargas en los circuitos de cableados de su casa o apartamento, lo cual podría representar un riesgo de incendio por el sobrecalentamiento de los alambres.
REQUISITOS ELÉCTRICOS
PRECAUCIÓN:
Bajo ninguna circunstancia corte o remueva la tercera púa (conexión a tierra) del cable eléctrico.
No cambie el enchufe en el cable eléctrico de este acondicionador de aire.
Los cables caseros de aluminio podrían presentar problemas especiales. Consulte a un técnico electricista calificado.
ANTES DE INICIAR
Lea estas instrucciones completa y cuidadosamente.
IMPORTANTE — Guarde estas
instrucciones para uso del inspector local.
IMPORTANTE — Observe todos
los códigos y órdenes de ley.
Nota al instalador – Asegúrese de dejar
estas instrucciones con el consumidor.
Nota al consumidor – Conserve estas
instrucciones para referencia futura.
Nivel de destreza – La instalación de este
aparato requiere de destrezas mecánicas básicas.
Tiempo de ejecución – Aprox. 1 hora
Recomendamos dos personas para
la instalación de este producto.
La instalación apropiada es la responsabilidad del instalador.
La falla del producto debido a una instalación inadecuada no está cubierta por la garantía.
El cable de alimentación incluye un dispositivo para interrupción de corriente. Se incluye un botón de prueba y de reinicio en el dispositivo. El dispositivo debe ponerse a prueba periódicamente: primero se presiona el botón de TEST (prueba) y luego RESET (reinicio). Si el botón TEST no se dispara o si el botón RESET no queda enganchado, deje de utilizar el acondicionador de aire y comuníquese con un técnico calificado.
HERRAMIENTAS QUE NECESITARÁ
Un destornillador de estrella
Una regla o cinta métrica
Lápiz
Nivel
Tijeras o cuchilla
Un destornillador
con hoja plana
Instrucciones de instalación
9
Tipo A (6)
Riel de montaje superior
Panel de
acordeón
derecho
Junta de
espuma superior
de la ventana
Sello de la banda
de la ventana
Panel de acordeón izquierdo
Tipo B (2) Tipo C (5)
Acondicionador
de aire
Soporte de cierre
de la ventana (1)
PARTES INCLUIDAS
(Apariencia puede variar)
Instrucciones de instalación
REQUISITOS PARA LA VENTANA
Estas instrucciones son para una ventana estándar de dos pliegues. Usted necesitará modificar el proceso para otros tipos de ventanas.
El acondicionador de aire puede instalarse sin los paneles de acordeón para ajustarse a una ventana más estrecha. Ver las dimensiones de la abertura de la ventana.
Todas las partes de apoyo deben quedar totalmente aseguradas a algún metal, mampostería o a la madera.
El tomacorriente eléctrico debe estar al alcance del cable eléctrico del acondicionador de aire.
Siga las dimensiones de la tabla y la
ilustración según su modelo.
Modelos A B C
AET05, AEW05 13 1/4″ mín. 22″–38″ 18 1/4″ mín.
AEW06, AEW08 14 1/2″ mín. 23″–38″ 19″ mín.
1
REQUISITOS DE UNA VENTANA DE TORMENTAS
Un marco de ventana de tormentas no permitirá que el acondicionador de aire se incline hacia el exterior y evitará que drene apropiadamente. Para solucionar este problema, adhiera un pedazo de madera a la repisa.
PIEZAS DE MADERA– ANCHO: 2 LONGITUD: Suficiente longitud para
ajustarse al interior del marco de la ventana. ESPESOR: Para determinar el espesor,
coloque un pedazo de madera en la repisa para hacerlo 1/2más alto que la parte superior del marco de la ventana de tormentas.
Una firmemente con puntillas o tornillos provistos por el instalador.
1/2″ más alto que el marco
Marco de ventana de tormentas
Madera
Repisa
2
10
PREPARE EL ACONDICIONADOR DE AIRE
Instale el riel de montaje superior con 2 tornillos tipo B desde la parte exterior de la caja.
Deslice los paneles de acordeón izquierdo y derecho en los rieles de montaje superior e inferior.
3
A
B
Riel de montaje superior
Riel de montaje inferior
Superior izquierda
Superior derecha
A
(con paneles de acordeón)
(sin paneles de acordeón)
B
C
Instrucciones de instalación
11
PREPARE LA VENTANA
Corte el sello de la banda de la ventana a la longitud apropiada. Despegue la parte posterior y pegue el sello a la parte inferior de la banda de la ventana.
4
INSTALE EL ACONDICIONADOR DE AIRE EN LA VENTANA
Coloque el acondicionador de aire en la repisa con el riel de montaje inferior contra su extremo posterior. Céntrelo y cierre la ventana firmemente detrás del riel de montaje superior. Debe estar nivelado o ligeramente inclinado hacia el exterior. Use un nivel; una inclinación de 1/3 de burbuja será la correcta hacia el exterior.
Extienda los paneles de acordeón izquierdo y derecho hacia las bandas de la ventana vertical y pegue, a través de los huecos de los paneles, con 4 tornillos tipo C según corresponda.
5
A
B
INSTALE UN SOPORTE DE CIERRE Y LA JUNTA DE ESPUMA SUPERIOR DE LA VENTANA
Una el soporte de cierre con uno tornillo tipo C.
Corte la junta de espuma superior de la ventana al ancho de la ventana.
Rellene la espuma entre el vidrio y la ventana para evitar que aire e insectos se introduzcan en la habitación.
6
A
B
C
Tornillos tipo C
o
o
PREPARE EL ACONDICIONADOR DE AIRE (cont.)
Una los paneles de acordeón a la caja usando 3 tornillos tipo A en cada lado.
3
C
Tornillos tipo A
Riel de montaje superior
Riel de montaje inferior
Panel de acordeón
POSTERIOR
12
Servicio al consumidor

Solucionar problemas Operación SeguridadInstalación

Solucionar problemas.
Problema Causas posibles Qué hacer
El acondicionador de aire El acondicionador de aire Cerciórese de que el acondicionador de aire está no enciende está desconectado. enchufado totalmente en el tomacorriente.
El fusible se disparó / Inspeccione los fusibles / caja de interruptores de la casa el cortacircuitos se disparó. y reemplace cualquier fusible o reajuste el interruptor.
Interrupción en el La unidad se reiniciará automáticamente con la configuración suministro eléctrico. utilizada por última vez luego de reestablecer la electricidad.
Existe un retraso de tiempo por protección (de aproximadamente 3 minutos) para evitar la desconexión por sobrecarga del compresor. Por esta razón, es posible que la unidad no comience a enfriar de forma normal hasta transcurridos 3 minutos desde que volvió a encenderse.
El dispositivo de interrupción Presione el botón RESET ubicado en el cable de alimentación. de corriente se ha activado.
Si el botón RESET no se mantiene en su lugar, no utilice más el acondicionador de aire y comuníquese con un técnico calificado.
El acondicionador de aire El flujo de aire está restringido. Cerciórese de que no existe ninguna cortina, persiana o no enfría como debería mueble bloqueando el frente del acondicionador de aire.
El control de temperatura no En los modelos con teclado: En el modo Cool (Frío), presione la tecla está ajustado apropiadamente. Reducción ▼.
En los modelos con botones, gire la temperatura a un número mayor.
El filtro de aire está sucio. Limpie el filtro cada 30 días por lo menos. Ver la sección
de Instrucciones de Operación.
La habitación podría haber Cuando el acondicionador de aire se enciende, usted estado caliente. necesita darle tiempo para que enfrié la habitación.
El aire frío se está escapando. Cerciórese de que los registros de la calefacción no están
abiertos y se encuentran retornando el aire frío.
Las bobinas de enfriamiento Ver “Acondicionador de aire congelándose” más adelante. se congelaron.
El acondicionador de aire El hielo bloquea el flujo En modelos con los botones de control, coloque el control se está congelando de aire hacia el acondicionador de modo en High Fan (Ventilador Alto) ó High Cool (Frío Alto) con
de aire evitando que se enfríe la temperatura en 1 ó 2. la habitación.
En los modelos con teclas de toque, colo que los controles en
High Fan (Ventilador Alto) ó High Cool (Frío Alto) y ajuste el termostato a una temperature más alta.
El control remoto Las baterías están insertadas Inspeccione la posición de las baterías. Deben estar no funciona incorrectamente. insertadas en la posición indicada, (+) y (–).
Las baterías están agotadas. Reemplace las baterías.
Hay agua goteando afuera Tiempo húmedo y caliente. Esto es normal. Hay agua goteando en el El acondicionador de aire Para drenar el agua apropiadamente, cercíorese de que
interior de la habitación no está inclinado hacia afuera. el acondicionador de aire está inclinado ligeramente
desde el frente hacia atrás.
Se acumula agua en La humedad removida del aire Esto es normal por un corto período en áreas con poca la bandeja y se drena hasta la bandeja. humedad; normal por un período de tiempo más postergado
en áreas más húmedas.

Sonidos de operación normales

Quizás escuche un sonido metálico causado por
el agua tomada y tirada contra el condensador en los días lluviosos o cuando la humedad es alta. Esta característica de diseño ayuda a remover la humedad y mejora la eficiencia.
Quizás escuche que el termostato hace clic
cuando el compresor hace ciclo entre encendido y apagado.
El agua se acumula en la bandeja durante días
lluviosos o con mucha humedad. El agua podría derramarse y gotear desde el lado externo de la unidad.
El ventilador podría funcionar aun si el compresor
no lo hace.
13
Servicio al consumidorSolucionar problemas
OperaciónSeguridad Instalación
Garantía de su acondicionador de aire—garantía limitada de un año.
Por el período de: Nosotros reemplazaremos:
Un año Unidad de reemplazo para cualquier producto que falle debido a defectos en los materiales o en
A partir de la fecha el proceso de fabricación. La unidad de intercambio está garantizada para el resto del período de la compra original de un año de garantía original del producto.
Instrucciones al cliente. El Manual del propietario
proporciona información acerca de las instrucciones de operación y de los controles del usuario.
Instalación inapropiada. Si usted tiene un problema
durante la instalación, o si su acondicionador de aire no tiene la capacidad de enfriamiento que usted necesita, póngase en contacto con nuestro distribuidor o instalador. Usted es responsable de proporcionar las facilidades de conexión eléctrica necesarias.
Fallo del producto resultante de modificaciones al
producto o debido a uso irrazonable incluyendo no proporcionar mantenimiento razonable y necesario.
Reemplazo de fusibles de la casa o reajuste del sistema
de circuitos.
Daño al producto causado por voltaje inapropiado hacia
el equipo, accidentes, incendios, inundaciones o actos de la naturaleza de fuerza mayor.
Daños incidentales o consecuenciales causados por
defectos posibles con este acondicionador de aire.
Lo que no está cubierto:
Esta garantía se extiende al comprador original y cualquier comprador posterior de productos comprados para uso residencial dentro de Estados Unidos.
Algunos estados no permiten la exclusión o las limitaciones de daños incidentales o consecuenciales. Esta garantía da derechos legales específicos, y usted podría tener otros derechos que variarán de estado a estado. Para saber cuáles son sus derechos legales, consulte a la oficina de asuntos del consumidor local o la oficina del Attorney General en su localidad.
Exclusión de garantías implicadas: Excepto donde está prohibido o restringido por la ley, no hay garantías, expresas, orales o estatutarias que extiendan más allá de la descripción específica, incluyendo específicamente las garantías implicadas de mercantibilidad o propiedad para un propósito particular.
Garante: General Electric Company. Louisville, KY 40225
Grape aquí su recibo. Se requiere facilitar prueba de la fecha de compra original para hacer un reclamo de garantía.
Empaque su unidad apropiadamente. Recomendamos
usar el cartón original y los materiales de empaquetado.
Regrese el producto al local de ventas donde usted
lo compró.
Incluya en el paquete una copia del recibo de venta
u otra evidencia de la fecha original de la compra. Además imprima su nombre y dirección y una descripción del defecto.
Para hacer un reclamo de garantía:
Impreso en China
14
Servicio al consumidor.
Página Web de GE Appliances
ge.com
¿Tiene alguna pregunta sobre su electrodoméstico? ¡Pruebe la página Web de GE Appliances 24 horas al día, cualquier día del año! Para mayor conveniencia y servicio más rápido, ya puede descargar los Manuales de los Propietarios, o incluso pedir piezas o catálogos hacer una cita en línea. También puede “Ask Our Team of Experts™” (Preguntar a nuestro equipo de expertos) sobre cualquier cuestión y mucho más...
Real Life Design Studio (Estudio de diseño para la vida real)
ge.com
GE apoya el concepto de Diseño Universal—productos, servicios y ambientes que pueden usar gente de todas las edades, tamaños y capacidades. Reconocemos la necesidad de diseñar para una gran gama de habilidades y dificultades físicas y mentales. Para más detalles cobre las aplicaciones de GE Diseño Universal, incluyendo ideas de diseño para la cocina para personas con discapacidades, mire nuestra página Web hoy mismo. Para personas con dificultades auditivas, favor de llamar al 800.TDD.GEAC (800.833.4322).
Piezas y accesorios
ge.com
Aquellos individuos con la calificación necesaria para reparar sus propios electrodomésticos pueden pedir que se les manden las piezas o accesorios directamente a sus hogares (aceptamos las tarjetas VISA, MasterCard y Discover). Haga su pedido en línea hoy, 24 horas cada día o llamar por teléfono al 800.626.2002 durante horas normales de oficina.
Las instrucciones descritas en este manual cubren los procedimientos a seguir por cualquier usuario. GE no está no apoya que se le proporcione ningún servicio al acondicionador de aire. Vehementemente recomendamos que usted no intente proporcionar servicio al acondicionador de aire usted mismo.
Póngase en contacto con nosotros
ge.com
Si no está satisfecho con el servicio que recibe de GE, póngase en contacto con nosotros en nuestra página Web indicando todos los detalles así como su número de teléfono o escríbanos a:
General Manager, Customer Relations GE Appliances, Appliance Park Louisville, KY 40225
Loading...