GE ADEW30, ADEW50, ADEW65 User Manual
GEAppliances.com
Safety Instructions ......................... 2, 3
Operating Instructions
About the Controls
on the Dehumidifier ....................................4
Automatic Defrost ......................................... 5
Choosing a Location .................................... 5
How the Dehumidifier Operates ............ 5
Removing Collected Water .................... 6
Water Level ...................................................... 6
Care and Cleaning
Air Filter ............................................................. 7
Grille and Case ................................................7
Water Bucket ...................................................7
Troubleshooting Tips ......................... 8
Consumer Support
Consumer Support ...................Back Cover
Ownership Registration for
Customers in Canada only ................9, 10
Warranty for Customers
in Canada ........................................................13
Warranty for Customers
in the U.S.A. .....................................................12
Owner’s Manual
ADEW30
ADEW50
ADEW65
Déhumidificateur
Manuel d’utilisation
La section française commence à la page 14
Deshumedificador
Manual del propietario
EnErgy Star® labeled product
As an EnErgy Star® partner, GE has
determined that this product meets the
EnErgy Star® guidelines for energy efficiency.
Write the model and serial numbers here:
Model # _________________________
Serial # _________________________
Dehumidifiers
You can find them on a label on the back
of the dehumidifier.
In Canada, contact us at:
www.GEAppliances.ca
La sección en español empieza en la página 26
49-7641 03-10 GE
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock
or personal injury.
SAFETY PRECAUTIONS
When using this dehumidifier, always follow basic safety precautions, including the following:
■ Use this appliance only for its intended
purpose as described in this Owner’s Manual.
■ This dehumidifier must be properly installed
and grounded as described
in this manual before it is used.
■ Never operate this dehumidifier in an area
that is likely to accumulate standing water.
If this condition develops, for your safety
disconnect the power supply before stepping
into the water.
■ Never unplug your dehumidifier by pulling on
the power cord. Always grip plug firmly and
pull straight out from the receptacle.
■ Replace immediately all electric service
cords that have become frayed or otherwise
damaged. A damaged power supply cord
must be replaced with a new power supply
cord obtained from the manufacturer and not
repaired. Do not use a cord that shows cracks
or abrasion damage along its length or at
either the plug or connector end.
■ If the receptacle does not match the plug,
the receptacle must be changed out by a
qualified electrician
■ GE does not support any servicing of
■ For your safety, do not store or use
■ All dehumidifiers contain refrigerants, which
■ Do not use outdoors.
■ This dehumidifier is intended for
■ These R410A Dehumidifier Systems require
the dehumidifier. We strongly recommend
that you do not attempt to service the
dehumidifier yourself.
combustible materials, gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
under federal law must be removed prior to
product disposal. If you are getting rid of an
old product with refrigerants, check with the
company handling disposal about what to
do.
indoor residential applications only.
This dehumidifier should not be used
for commercial or industrial applications.
contractors and technicians to use tools,
equipment and safety standards approved
for use with this refrigerant. DO NOT use
equipment certified for R22 refrigerant only.
■ Turn the dehumidifier OFF and unplug it
before cleaning.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be properly
grounded.
DO NOT use an adapter plug with this appliance.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric
shock hazard from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsTroubleshooting Tips Care and Cleaning Safety InstructionsOperating Instructions
2
Where a 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded
3-prong wall outlet.
The dehumidifier should always be
plugged into its own individual electrical
outlet, which has a voltage rating matching
the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits, which
could cause a fire hazard from overheated wires.
USE OF EXTENSION CORDS
GEAppliances.com
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord.
However, if you must use an extension
cord, it is absolutely necessary that it be
a UL-listed, 14 -gauge, 3-wire grounding
type appliance extension cord having
a grounding-type plug and outlet and
that the electrical rating of the cord be
15 amperes (minimum) and 125 volts.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Care and Cleaning
3
About the controls on the dehumidifier.
4 hour or 2 hour
delay off
indicator lights
High, Medium
and Low fan
indicator lights
Controls
NOTE: When the bucket is full or removed, the
controls cannot be set.
Power Pad
Press to turn the dehumidifier on and off.
Filter Timer
After 250 hours of operation, the Clean the Filter
indicator light will glow to remind you to clean
the filter. Remove the filter and clean it.
Press to turn off the Clean the Filter light. See
the Care and Cleaning section.
Humidity Set Control Pads
The humidity level can be set within a range of
35% RH (Relative Humidity) to 80% RH (Relative
Humidity) in 5% increments or at CO for
continuous operation. To set the unit for
continuous operation, press the ▼ pad until
the screen reads CO.
NOTE: If CO (Continuous) is selected, the
dehumidifier will operate continuously at
its maximum dehumidification settings if
attached to a hose to drain or until the bucket
is full.
For drier air, press the ▼ pad and set to
a lower percent value (%).
For damper air, press the ▲ pad and set
to a higher percent value (%).
Clean the Filter
indicator light
Continuous operation on
indicator light
Bucket Full light indicates
bucket needs to be emptied
or is not in place in the unit
Power On
indicator light
When you first use the dehumidifier, set
the humidity control to 45% or 50%. Allow at
least 24 hours for the dehumidifier to achieve
the humidity level. If you still have damper air
than desired, set the humidity level to a lower
setting or select Continuous for maximum
dehumidification.
Display
Shows the set % humidity level while setting,
then shows the actual (+/– 5% accuracy)
room % humidity level.
Fan Speed Pad
Controls the fan speed.
Press to select either High, Medium or Low fan
speed.
Set the fan control to High for maximum
moisture removal. When the humidity
has been reduced and quiet operation is
preferred, set the fan control to Medium
or Low.
Delay Off
While the dehumidifier is in operation, press
this pad to set it to automatically turn off in 2
hours or 4 hours.
Other Features
BUCKET FULL Light
Glows when the bucket is ready to be emptied, or
when the bucket is removed or not replaced in the
proper position.
Alarm
If the bucket is full or missing for more than 3
minutes, an alarm will sound for about 10 seconds
to remind you to empty and replace the bucket.
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsTroubleshooting Tips Care and Cleaning Safety InstructionsOperating Instructions
4
Auto Shut Off
The Water Level Control Switch shuts off the
dehumidifier when the bucket is full, or when
the bucket is removed or not replaced in the
proper position. NOTE: Fan will continue to run
approximately 3 minutes after bucket is removed.
Auto Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue
to run until the frost disappears.
Power Outage
In the case of a power outage or interruption, the
unit will automatically restart, in the settings last
used, after the power is restored.
Using the dehumidifier. GEAppliances.com
When first using the dehumidifier, operate the unit continuously for 24 hours.
How the Dehumidifier Operates
Moist, humid air is drawn over a cold refrigerated
dehumidifying coil. Moisture in the air condenses on
this coil and drains into a bucket (or through
a hose and drain).
Dry, clean air is drawn through the condenser where
it is heated and discharged out the top grille into the
room.
It is normal for the surrounding air to become slightly
warmer as the dehumidifier operates.
Choosing a Location
A dehumidifier operating in a basement will have little
or no effect in drying an adjacent enclosed storage
area, such as a closet, unless there is adequate
circulation of air in and out of the area.
■ Do not use outdoors.
■ This dehumidifier is intended for indoor residential
applications only. This dehumidifier should not be
used for commercial or industrial applications.
■ Place the dehumidifier on a smooth, level floor strong
enough to support the unit with a full bucket of water.
■ Allow at least 12–18 inches of air space on all sides of
the unit for good air circulation.
■ Place the dehumidifier in an area where the
temperature will not fall below 41°F (5°C). The coils
can become covered with frost at temperatures
below 41°F, which may reduce performance.
■ Use the dehumidifier in cooking, laundry, bathing
and dishwashing areas that have excessive moisture.
NOTE: Place the dehumidifier away
from the clothes dryer.
■ Use the dehumidifier to prevent moisture damage
anywhere books or valuables are stored.
■ Use the dehumidifier in a basement to help prevent
moisture damage.
■ The dehumidifier must be operated in an enclosed
area to be most effective.
■ Close all doors, windows and other outside openings
to the room.
Automatic Defrost
When frost builds up on the evaporator coils, the
compressor will cycle off and the fan will continue to
run until the frost disappears.
When the coil is defrosted, the compressor or fan will
automatically restart and dehumidifying will resume.
YES NO
12″–18″ min. 12″–18″ min.
NOTE: The dehumidifier has rollers to aid placement,
but it should only be rolled on smooth, flat surfaces.
Do not attempt to roll the dehumidifier on carpet or
over objects.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Care and Cleaning
5
Using the dehumidifier.
Always make sure the water bucket is locked into place on the dehumidifier.
Removing Collected Water
There are 2 ways to remove collected water:
Use the bucket. When the bucket is removed,
the unit will shut off. Empty and replace
the bucket.
NOTE: Support bucket with
both hands when emptying.
IMPORTANT: Do not use the hose if using
the bucket to collect water. When the hose
is connected, water will flow through it onto
the floor instead of into the bucket.
NOTES:
■ Do not remove the bucket while the
dehumidifier is operating or if it has just stopped
operating. This might cause some water to drip
from the drain pan.
■ The bucket must be in place and securely
seated for the dehumidifier to operate.
Use a hose. Water can be automatically
emptied into a floor drain by attaching
a garden water hose (not included).
1. Remove the bucket from the front of
the unit.
2. Open the drain cover on the side of
the unit.
3. Thread a garden hose (not supplied)
onto the nozzle, cut to length, and lead it
to the floor drain.
Side of unit
4. Replace the bucket in the unit.
NOTE: The bucket must be in place and securely
seated for the dehumidifier to operate.
Water Level
The dehumidifier will turn off automatically
when the bucket is full, or when the bucket is
removed or not replaced in the proper position.
The bucket must be replaced in the proper position
for the dehumidifier to work. The light will be on
and the dehumidifier will not run if the bucket is not
in the proper position.
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsTroubleshooting Tips Care and Cleaning Safety InstructionsOperating Instructions
6
Care and cleaning of the dehumidifier. GEAppliances.com
Turn off the dehumidifier and remove the plug from the wall outlet before cleaning.
Grille and Case
To clean the case:
Use water and a mild detergent. Do not use
bleach or abrasives.
Water Bucket
To clean:
Every few weeks, clean the bucket to prevent growth
of mold, mildew and bacteria. Partially fill the bucket
with clean water and add a little mild detergent.
Swish it around in the bucket, empty and rinse.
NOTE: Do not use a dishwasher to clean the
water bucket.
To remove:
Remove the bucket and pour out any water.
To replace:
Slide the bucket into the dehumidifier.
NOTE: The bucket must be in place and securely seated
for the dehumidifier to operate.
To clean the front grille:
Use a vacuum attachment or brush.
Air Filter
The air filter behind the front grille should
be checked and cleaned at least every 250 hours
of operation or more often if necessary.
After 250 hours of operation, the Clean the Filter
indicator light will glow to remind you to clean the
filter. Remove the filter and clean it. Replace the filter
and press the Filter Timer pad to turn off the Clean the
Filter light.
To remove:
Remove the bucket. Grasp the filter edge, and pull it
straight down and out.
To clean:
Clean the filter with warm, soapy water. Rinse
and let the filter dry before replacing it.
NOTE: DO NOT rinse or put the filter in an automatic
dishwasher.
CAUTION:
DO NOT operate the dehumidifier without a filter because
dirt and lint will clog it and reduce performance.
NOTE: Avoid using a dishwasher to clean the filter.
Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Care and Cleaning
7
Troubleshooting tips…
Save time and money! Review the chart below first and you may not need to call for service.
Problem Possible Causes What To Do
Dehumidifier The dehumidifier •Make sure the dehumidifier’s plug is pushed completely
does not start is unplugged. into the outlet.
The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace
breaker is tripped. the fuse or reset the breaker.
Dehumidifier has reached its • The dehumidifier automatically turns off when either
preset level or bucket is full. condition occurs. Change to a lower setting or empty
the bucket and replace properly.
Bucket is not in the • The bucket must be in place and securely seated for the
proper position. dehumidifier to operate.
Power failure. • There is a protective time delay (up to 3 minutes) to
prevent tripping of the compressor overload. For this
reason, the unit may not start normal dehumidifying
for 3 minutes after it is turned back on.
Dehumidifier does not Did not allow enough time • When first installed, allow at least 24 hours to maintain
dry the air as it should to remove the moisture. the desired dryness.
Airflow is restricted. • Make sure there are no curtains, blinds or furniture
blocking the front or back of the dehumidifier. See the
Choosing a Location section.
Dirty filter. • See the Care and Cleaning section.
The Humidity Control may • For drier air, press the ▼ pad and set to a lower percent
not be set low enough. value (%) or at CO (continuous) for maximum
dehumidification.
Doors and windows may not • Check that all doors, windows and other openings
be closed tightly. are securely closed.
Clothes dryer may be • Install the dehumidifier away from the dryer.
blowing moisture-laden The dryer should be vented to the outside.
air into the room.
Room temperature • Moisture removal is best at higher room temperatures.
is too low. Lower room temperatures will reduce the moisture
removal rate. Models are designed to be operated at
temperatures above 41°F (5°C).
Dehumidifier runs Area to be dehumidified • The capacity of your dehumidifier may not be adequate.
too much is too large.
Doors and windows are open. • Close all doors and windows to the outside.
Frost appears on Dehumidifier has been turned • This is normal. Frost will usually disappear
the coils on recently, or room temperature within 60 minutes. See the Automatic Defrost section.
is below 41°F (5°C).
Controls cannot be set The compressor will turn off • This is normal. Wait approximately 3 minutes and set the
and the fan will automatically fan as desired.
continue to run for
approximately 3 minutes at a
fixed setting.
Fan noise Air is moving through • This is normal.
the dehumidifier.
Water on floor Hose connection may be loose. • Check the hose connection. See the Removing Collected
Water section.
Intended to use the bucket to • Disconnect the hose if using the bucket to collect water.
collect water, but a hose See the Removing Collected Water section
as attached.
Bucket Full LED light Drain hose not tight on fitting • Check drain hose connection.
flashing and alarm
sounds while drain hose Drain hose is kinked • Ensure the drain hose is pointed straight down to the floor
Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsTroubleshooting Tips Care and Cleaning Safety InstructionsOperating Instructions
is connected and is not kinked in anyway.
8
Please place in envelope and mail to:
Veuillez mettre dans une enveloppe et envoyez à :
OWNERSHIP REGISTRATION
P.O. BOX 1780
MISSISSAUGA, ONTARIO
L4Y 4G1
(FOR CANADIAN CONSUMERS ONLY)
9
10
Notes. GEAppliances.com
11
CustomerServiceTroubleshootingTipsOperatingInstructionsSafetyInstructions InstallationInstructions
Loading...