GE 24911, 34928, 34927 Instruction Manual
Universal Remote
Instruction Manual
24911 | 34927 | 34928
7252
V2| 3/17
dvd/vcr
dvd/vcr
2
Introduction ..................................................................................... 2
Setup .................................................................................................. 3
Button Functions .......................................................................... 4
Programming Your Remote ..................................................... 6
Direct Code Entry................................................................... 6
Auto Code Search ................................................................. 8
Controlling Combo Devices .............................................. 9
Using Your Remote ....................................................................10
Using SHIFT ............................................................................ 10
Master Volume Feature ....................................................11
Code Identification .............................................................12
Reset to Factory Settings .................................................12
Troubleshooting ..........................................................................13
Warranty ........................................................................................14
FCC Statement .............................................................................15
Table of Contents
Scan this QR code to view
remote setup video.
http://www.byjasco.com/remote
Congratulations on your purchase of this GE-branded
Universal Remote Control. This remote will operate
thousands of audio/video devices including TVs, DVD
players, cable boxes, satellite receivers and more!
IMPORTANT: SAVE THIS MANUAL AND CODE LIST
FOR FUTURE REFERENCE
3
Setup
Your universal remote requires two (2) AAA batteries
(not included). Alkaline batteries are recommended.
Battery Installation
1. On the back of the remote, push down on the tab
and pull the cover to remove.
2. Match the (+) and (-) marks on the batteries to the
(+) and (-) marks inside the battery compartment,
then insert two (2) AAA batteries. Be sure to use
fresh batteries.
3. Position the battery cover over the compartment,
then press the top until it snaps into place.
NOTE: If your remote stops operating properly, replace
the batteries with new ones.
Battery Precautions
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
• Always remove old, weak or worn-out batteries
promptly and recycle or dispose of them in
accordance with local and national regulations.
Battery Saver
Your remote automatically turns off if the buttons are
depressed more than 8 seconds. This will save your
batteries should your remote get stuck in a place
where the buttons remain depressed (e.g., between
the sofa cushions).
Code Saver
You have up to 10 minutes to change the batteries
in your remote without losing the codes you have
programmed.
4
Button Functions
1
2
6
8
9
12
13
11
10
7
4
3
5
5
Button Functions
1. Power - Turns devices ON/OFF
2. Red Indicator Light
3. TV, cbl/sat, dvd/vcr - Selects the device to control
4. Setup - Used to program the remote; Shift is the
alternate function of this button. Use the Shift
button to access the Menu, Ok and Exit functions
of your device. To enter the Shift mode press this
button once. To exit the Shift mode,
press the button again.
5. Record, play, stop, rewind, fast forward, pause
6. Input - Selects video inputs
7. Mute mutes sound Ok (Shift mode) - Selects menu
items for the controlled device;
8. Channel Up/Down, Volume Left/Right -
Control channels and volume; Menu Navigation
(Shift mode)
9. Info - Displays on-screen show/content
information; Menu (Shift mode) Displays the
on-screen menu
10. Previous Channel - Returns to the previously
selected channel; Exit (Shift mode) Exit
on-screen menus
11. Numbers - Used for direct channel selection
12. Dot (•) - Used to select digital channels, e.g., 4.1
13. Enter - Some devices require Enter to be pressed
after channel selection
6
Programming Your Remote
Your remote is designed to control multiple audio/video
devices. To use, you will need to program the remote for
your devices. There are two different methods you can
use to program the remote, Direct Code Entry or Auto
Code Search.
• The Direct Code Entry method is the recommended
method as it is the simplest and quickest method in
most cases.
• The Auto Code Search method searches through
all the codes in the remote to find a code for
your device.
Note: this remote comes preprogrammed for Samsung TVs. Press
TV for Samsung TVs.
Direct Code Entry (Recommended)
1. Locate the Code List included with
your remote. Find the section for the
type of device you wish to control,
(for example TV, cbl, dvd). Locate the
brand of your device and circle all the
remote codes for the brand.
2. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light will
remain on.
Note: The red light will either be a small light at the
top of the remote or the power ON/OFF button.
3. Press and release the device button on
the remote for the type of device you
wish to control, (for example TV, cbl,
dvd). The red light will blink once and
remain on.
Note: Any of the device buttons on the remote can
be programmed to control any of your devices. For
example, you can use the CBL device button on
the remote to control a Satellite Receiver, Digital
Converter Box, Streaming Media Player or any
device category in the Code List.
4. Use the number buttons on the remote
to enter the first 4-digit remote code
you circled in the Code List in Step 1.
7
Programming Your Remote
The red light will turn off after entering
the fourth digit.
5. Point the remote at the device. Test
the buttons on the remote to see if the
device responds as you would expect.
If the buttons do not operate the device,
return to Step 2 above and use the next
code that you circled for that device.
6. Repeat Steps 1 – 5 for each device you wish
to control.
Programming Notes
• Some codes may operate only a few functions of your
device. There may be another code in the Code List
that controls more functions. Test other codes in the
Code List for more functionality.
• If you do not find a remote code that works your
device or there are no codes in the Code List for your
device, use the Auto Code Search method in the next
section to program your remote.
• For combination devices such as a TV/DVD combo
or TV/ VCR combo, you may have to enter a code for
each device. (See Controlling Combo Devices, pg. 9.)
• Write down the remote codes used to program the
remote for future reference.
8
Programming Your Remote
Auto Code Search
The Auto Code Search is a process where you can
search through all the codes stored in the remote to find
a code for your device. It is recommended that you read
through all the steps below to familiarize yourself with
the Auto Code Search before starting the process.
1. Manually turn on the device you wish
to control.
Note: The Auto Code Search process cannot be
used for devices without power ON/OFF capability.
Use the Direct Code Entry method in these cases.
2. Press and hold down the SETUP button
on the remote until the red light on the
remote control turns on. Release the
SETUP button. The red light will remain on.
Note: The red light will either be a small light at the
top of the remote or the power ON/OFF button.
3. Press and release the device button on
the remote for the type of device you
wish to control, (for example TV, cbl,
dvd). The red light will blink once and
remain on.
4. With the remote pointed at the device,
press and release the POWER button
on the remote. The remote will send 10
different codes to the device. The red
light will blink once for each code and
remain on after sending the 10 codes.
Did the device turn off?
• If YES, go to Step 5.
• If NO, repeat Step 4 to test the next
10 codes.
5. Manually turn the device back on.
6. With the remote pointed at the device,
press and release the VOL
button. The
remote will re-send the first code of the
10 codes from Step 4. The red light will
blink once and remain on.
9
Programming Your Remote
Did the device turn off?
• If YES, you have found a code for the
device. Press and release the same device
button you pressed in Step 3. This will
store the code in the remote. Go to Step 7.
• If NO, continue to press and release the
VOL
button until the device turns off to
test the other 9 codes from Step 4.
Be sure to wait approximately 3 seconds
after each VOL button press to allow
the device time to respond to the code.
When the device turns off, you have
found a code for your device. Press and
release the same device button pressed
in Step 3. This will store the code in the
remote. Go to Step 7.
Notes:
• The VOL
button can be used to go backwards through
each batch of 10 codes.
• The red indicator light will flash 2 times after testing
the first or last code in each batch of 10.
7. Use the remote to turn the device back on.
Test the buttons on the remote to see if the
device responds as you would expect. If the
buttons do not operate the device, return to
Step 2 and repeat this process to search for a
better code to operate the device.
8. Repeat this process for each device you wish
to control.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD, DVD/
VCR, etc.) will require you to set up two different Mode
buttons to control both parts of the Combo device.
For example, if you have a TV/DVD Combo, you might
need to set up one code under the TV button to
control the TV part AND a separate code (under any
other Mode button) to control the DVD part.
10
Using Your Remote
NOTE: Remote will stay in shift mode until the SHIFT button is pressed
again, or until 10 seconds of inactivity. The red indicator light will blink
when the remote is in shift mode.
Using SHIFT Function
The Shift/Setup button allows access to
more than one function for certain buttons.
For Menu, press and release
Shift/Setup then Info/Menu.
For Exit, press and release Shift/
Setup then Previous channel/Exit.
For Ok, press and release Shift/
Setup then Mute/Ok.
For Up, Down, Left or Right
Navigation, press and release SHIFT/
SETUP then the respective Channel
or Volume button.
Loading...