GE 15433020 User Manual
26993/26994
40-Channel 900 MHz Caller ID
Cordless Telephone/Answerer
User’s Guide
1
We bring good things to life.
FCC REGISTRATION INFORMATION
Your telephone equipment is registered with the Federal Communications Commission and is in compliance with
parts 15 and 68, FCC Rules and Regulations.
1 Notification to the Local Telephone Company
On the bottom of this equipment is a label indicating, among other information, the FCC Registration number
and Ringer Equivalence Number (REN) for the equipment. You must, upon request, provide this information to
your telephone company.
The REN is useful in determining the number of devices you may connect to your telephone line and still have
all of these devices ring when your telephone number is called. In most (but not all) areas, the sum of the
RENs of all devices connected to one line should not exceed 5. To be certain of the number of devices you
may connect to your line as determined by the REN, you should contact your local telephone company.
Notes
• This equipment may not be used on coin service provided by the telephone company.
• Party lines are subject to state tariffs, and therefore, you may not be able to use your own telephone
equipment if you are on a party line. Check with your local telephone company.
• Notice must be given to the telephone company upon permanent disconnection of your telephone from
your line.
2 Rights of the Telephone Company
Should your equipment cause trouble on your line which may harm the telephone network, the telephone
company shall, where practicable, notify you that temporary discontinuance of service may be required.
Where prior notice is not practicable and the circumstances warrant such action, the telephone company may
temporarily discontinue service immediately. In case of such temporary discontinuance, the telephone
company must: (1) promptly notify you of such temporary discontinuance; (2) afford you the opportunity to
correct the situation; and (3) inform you of your right to bring a complaint to the Commission pursuant to
procedures set forth in Subpart E of Part 68, FCC Rules and Regulations.
The telephone company may make changes in its communications facilities, equipment, operations of
procedures where such action is required in the operation of its business and not inconsistent with FCC Rules
and Regulations. If these changes are expected to affect the use or performance of your telephone equipment,
the telephone company must give you adequate notice, in writing, to allow you to maintain uninterrupted
service.
INTERFERENCE INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference; and (2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna (that is, the antenna for radio or television that is “receiving” the
interference).
• Reorient or relocate and increase the separation between the telecommunications equipment and receiving
antenna.
• Connect the telecommunications equipment into an outlet on a circuit different from that to which the
receiving antenna is connected.
If these measures do not eliminate the interference, please consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal Communications Commission has prepared a helpful
booklet, “How To Identify and Resolve Radio/TV Interference Problems.” This booklet is available from the U.S.
Government Printing Office, Washington, D.C. 20402. Please specify stock number 004-000-00345-4 when
ordering copies.
HEARING AID COMPATIBILITY
This telephone system meets FCC standards for Hearing Aid Compatiblility.
2
FCC NUMBER IS LOCATED ON THE CABINET BOTTOM
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
INTRODUCTION
Your cordless telephone/answerer with Caller ID is designed to give you flexibility
in use and high quality performance. To get the most from your new cordless
telephone/answerer, we suggest that you take a few minutes right now to read
through this instruction manual.
TABLE OF CONTENTS
FCC REGISTRATION INFORMATION .......... 2
INTERFERENCE INFORMATION .................. 2
HEARING AID COMPATIBILITY .................. 2
GETTING STARTED ......................................... 5
BEFORE YOU BEGIN................................... 5
MODULAR JACK REQUIREMENTS............. 5
DIGITAL SECURITY SYSTEM ......................... 5
DESKTOP INSTALLATION .............................. 6
WALL MOUNT INSTALLATION ....................... 7
ANSWERING MACHINE SETUP ..................... 9
SETTING THE VOICE TIME/DAY STAMP..... 9
SETTING THE SPEAKER VOLUME ........... 10
VOICE INSTRUCTIONS .......................... 10
SETTING THE RING SELECT .................. 10
USING TOLL SAVER............................ 10
RECORDING THE OUTGOING
ANNOUNCEMENT ......................... 11
REVIEWING ANNOUNCEMENT................ 11
TELEPHONE SETUP .................................. 12
SETTING THE DISPLAY LANGUAGE ......... 12
SETTING THE LOCAL AREA CODE .......... 12
CORDLESS PHONE BASICS ............................ 13
MAKING A CALL...................................... 13
REDIAL .................................................. 13
RECEIVING A CALL ................................... 14
FLASH ................................................... 14
VOLUME ................................................ 14
MUTE.................................................... 14
RINGER SWITCH ...................................... 15
FINDING THE HANDSET ............................. 15
CALLER ID FEATURES................................... 16
CALLER ID WITH CALL WAITING ................ 16
RECEIVING AND STORING CALLS ................ 16
REVIEWING MESSAGES ............................. 17
DELETING RECORDS ................................. 18
DELETING THE CURRENT RECORD .......... 18
DELETING ALL RECORDS ..................... 18
DIALING A CALLER ID NUMBER ................. 18
CHANGING THE NUMBER FORMAT .............. 19
MEMORY ................................................... 20
STORING A NUMBER IN MEMORY............... 20
CHANGING A STORED NUMBER.................. 21
DIALING A STORED NUMBER ..................... 22
USING DIAL ........................................... 22
CHAIN DIALING FROM MEMORY ............ 23
INSERTING A PAUSE IN THE DIALING
SEQUENCE ................................. 24
REVIEWING AND DELETING STORED
NUMBERS .................................. 24
ADVANCED FEATURES ................................... 25
CHANNEL BUTTON ................................... 25
TEMPORARY TONE ................................... 25
MESSAGES INDICATOR.............................. 26
SCREENING CALLS FROM THE BASE ............. 26
ANSWERING MACHINE OPERATION ................. 26
MESSAGE PLAYBACK ............................... 27
MEMORY FULL........................................ 27
ERASING MESSAGES ................................ 27
LEAVING A MEMO ................................... 28
(Table of Contents continued on
the following page.)
WARNING:
OR ELECTRICAL SHOCK HAZARD,
DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
TO PREVENT FIRE
CAUTION
RISK OF ELECTRIC SHOCK
THE LIGHTNING
FLASH AND ARROW HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
"DANGEROUS
VOLTAGE" INSIDE
THE PRODUCT.
DO NOT OPEN
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER
(OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
3
REMOTE ACCESS ......................................... 29
USING THE HANDSET ............................... 30
ANSWERER INDICATOR ........................ 30
SCREENING CALLS
THE HANDSET..................... 31
FROM
ACCESSING THE ANSWERER FROM ANOTHER
LOCATION .................................. 32
CHANGING THE SECURITY CODE................. 33
HEADSET AND BELT CLIP OPERATION .............. 34
CONNECTING A HEADSET TO THE HANDSET ... 34
CONNECTING THE BELT CLIP...................... 34
CHANGING THE BATTERY............................... 35
BATTERY SAFETY PRECAUTIONS............ 35
GENERAL PRODUCT CARE ............................. 36
HANDSET SOUND SIGNALS ........................... 36
HANDSET INDICATORS .................................. 37
ANSWER STATUS INDICATORS ........................ 38
TROUBLESHOOTING GUIDE ............................ 39
CORDLESS PHONE SOLUTIONS ............. 39
CALLER ID........................................ 40
ANSWERING MACHINE SOLUTIONS........ 41
CAUSES OF POOR RECEPTION ........................ 42
SERVICE ..................................................... 42
INDEX ........................................................ 43
ACCESSORY ORDER FORM ............................ 45
LIMITED WARRANTY ..................................... 47
4
BEFORE YOU BEGIN
W
X
Y
Z
9
T
U
V
8
P
Q
R
S
7
M
N
O
6
J
K
L
5
G
H
I
4
D
E
F
3
A
B
C
21
#
O
P
E
R
0
T
O
N
E
*
C
H
A
N
N
E
L
F
L
A
S
H
I
N
T
R
E
D
I
A
L
M
E
M
D
E
L
E
T
E
D
I
A
L
F
O
R
M
A
T
M
U
T
E
P
R
O
G
P
A
U
S
E
TA
L
K
A
N
S
W
E
R
A
S
E
P
L
A
Y
/
S
T
O
P
S
K
I
P
R
E
V
I
E
W
NEXT
ANNOUNCE
MEMO
ERASE ANSWER
ON/OFF
HOUR MIN
DAY/
CHECK
PAGE
CORDLESS TELEPHONE
DIGITAL ANSWERER
900 MHz
CHARGE/
IN USE
MESSAGES
8.8.
S
K
I
P
R
E
V
I
E
W
P
L
A
Y
/
S
T
O
P
PARTS CHECKLIST
Make sure your package includes the items shown here.
Short telephone
line cord
AC power supply
Long telephone line
cord
Mounting bracket
Headset (provided
with 26994 only)
Belt clip
(provided with
26994 only)
Base Handset
MODULAR JACK REQUIREMENTS
You need an RJ11 type modular jack, which is the most
common type of phone jack and might look like the one
pictured here. If you don’t have a modular jack, call your
local phone company to find out how to get one installed.
DIGITAL SECURITY SYSTEM
Your cordless phone uses a digital security system to protect against false
ringing, unauthorized access, and charges to your phone line.
When you place the handset in the base, the unit verifies its security code.
After a power outage or battery replacement, you should place the
handset in the base for about 20 seconds to reset the code.
IMPORTANT: Because cordless phones operate on electricity, you should
have at least one phone in your home that isn’t cordless, in case the power in
your home goes out.
5
DESKTOP
3
INSTALLATION
4
6
1. Make sure the mounting bracket is securely fastened.
7
5
1
2
TONE/PULSE
switch
2. Set the TONE/PULSE switch to TONE for touch-tone service, or PULSE
for rotary service. If you don’t know which type of service you have,
check with the phone company.
3. Set RINGER switch (on the handset) to ON.
4. Plug the power supply cord into the POWER 9V DC jack on the base and
into an AC outlet.
5. Place handset in the base to charge for 12 hours. The CHARGE indicator (on
the base) comes on to indicate that the battery is charging. If you don’t
charge the handset battery properly (for 12 hours) when you first set
up the phone, performance of the battery will be compromised.
6. Plug the long telephone line cord into the TEL LINE jack on the base
and into a modular jack.
7. Raise the base antenna.
CAUTION: Use only the Thomson 5-2472(black)/5-2471(white) power supply
that came with this unit. Using other power supplies may damage the unit.
INSTALLA TION NOTE: Some cordless telephones operate at frequencies that
may cause interference to nearby TVs and VCRs. To minimize or prevent such
interference, the base of the cordless telephone should not be placed near or on
top of a TV or VCR. If interference continues, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
6
NEXT
ANNOUNCE
MEMO
ERASE ANSWER
ON/OFF
HOUR MIN
DAY/
CHECK
PAGE
CORDLESS TELEPHONE
DIGITAL ANSWERER
900 MHz
CHARGE/
IN USE
MESSAGES
8.8.
S
K
I
P
R
E
V
I
E
W
P
L
A
Y
/
S
T
O
P
WALL MOUNT INSTALLATION
Because it is necessary to charge the
handset for 12 hours prior to connecting
the phone for use the first time, it is
better to leave the unit on a flat surface
during initial charge before attempting
to hang it on the wall.
1. Make sure the mounting bracket is
securely fastened.
2. Set the TONE/PULSE switch to TONE
for touch-tone service, or PULSE for
rotary service. If you don’t know
which type of service you have, check
with the phone company.
3. Set RINGER switch to ON.
4. Place the handset in the base.
5. Connect the power supply cord into
the base and the other end into an AC
outlet. The CHARGE indicator comes
on, indicating the battery is charging.
Allow the phone to charge for 12
hours before using the first time.
If you don't charge the phone
properly when you first set up
the phone, performance of the
battery will be compromised.
(Installation continued on the
following page.)
1
5
2
PROG
FORMAT MUTE
DELETEDIAL
TALK
PAUSE
REDIAL MEM
PLAY/STOP SKIPREVIEW
DEF3ABC
21
MNO6JKL5GHI
4
WXYZ9TUV
PQRS
8
7
*
CHANNEL FLASHINT
ERASE
OPER0TONE
#
ANSW
3
CAUTION: Use only the Thomson
5-2472(black)/5-2471(white)
power supply that came with this
unit. Using other power supplies
may damage the unit.
4
7
6. Remove the mounting bracket. Rotate it
so that the bottom of the phone is flat.
Reattach the wall mount bracket by
inserting the tabs into the slots on the
top of the unit first, and then snapping
the bottom tabs into place.
7. Plug the short telephone line cord into
the jack marked TEL LINE on the back of
the unit and plug the other end into a
modular wall jack.
8. Slip the mounting holes over the wall
plate posts and slide the unit down
firmly into place. (Wall plate not
included.)
9. Remove the handset hook; turn it
upside down, and put it back in the slot.
You need to do this so the handset
doesn’t fall out of the base.
10. Raise the base antenna.
10
9
6
8
7
8
NEXT
ANNOUNCE
MEMO
ERASE ANSWER
ON/OFF
CHARGE/
IN USE
MESSAGES
8.8.
S
K
I
P
R
E
V
I
E
W
P
L
A
Y
/
S
T
O
P
ANSWERING MACHINE SETUP
HOUR MIN
DAY/
CHECK
PAGE
CORDLESS TELEPHONE
DIGITAL ANSWERER
900 MHz
This section shows you how to set up your
answering machine to receive incoming
calls. Before you begin the setup, you
must turn on the answerer.
• Press the ANSWER ON/OFF button to
turn the answering machine on and off.
The MESSAGES indicator lights when
the answering machine is on. The
indicator blinks when you have
messages.
NOTE: The answerer displays “- -” when it is
off.
ANSWER ON/OFF
(answerer on/off) button
SETTING THE VOICE TIME/DAY STAMP
1. Make sure the answerer is ON.
2. Press and hold the DAY/CHECK button
to set the day of the week.
3. Press the HOUR button to set the hour
(a.m. or p.m.).
4. Press the MIN button to set the minute.
When you press and hold the MIN
button, the time advances in 5-minute
intervals.
5. Press and release the DAY/CHECK
button to review the day and time
settings.
MESSAGES indicator
Time set buttons
9
SETTING THE SPEAKER VOLUME
Use the VOL (volume) control to adjust
speaker volume to a comfortable level.
VOICE INSTRUCTIONS
If you need additional assistance, press the
REVIEW button when you plug in the
answerer and follow the voice instructions.
SETTING THE RING SELECT
Set the RING SELECT switch on the back of
the unit to choose the number of times you
want the phone to ring before the machine
answers the call. You can choose 2 rings, 5
rings, or TOLL SAVER.
USING TOLL SAVER
Toll Saver can save you the cost of a call
when you access your messages from
another phone:
• If you have new messages, the unit
answers after the 2nd ring.
• If you have no new messages, the unit
answers after the 5th ring.
You can hang up after the 3rd or 4th ring
and save the pay telephone or long distance
charge.
Speaker volume control
RING SELECT switch
L
O
V
10
RECORDING THE OUTGOING ANNOUNCEMENT
For best results when recording, you should
be about 9 inches from the microphone,
and eliminate as much background noise as
possible.
1. Make sure the answerer is ON.
2. Press and hold the ANNOUNCE button.
You need to hold the button until you
finish the announcement.
3. Begin talking after you hear the beep.
4. Release the button when you finish your
announcement.
If you choose not to record an outgoing
announcement, a default announcement
will play. To return to the default
announcement after you have recorded
your own outgoing announcement, press
the ANNOUNCE button and release it when
you hear the beep.
Sample Outgoing Announcement
Hi, this is (use your name here), I can't answer the
phone right now, so please leave your name, number
and a brief message after the tone, and I'll get back to
you. Thanks.
Microphone
ANNOUNCE
NEXT
I
E
V
W
E
R
ERASE ANSWER
MEMO
S
/
T
Y
O
A
L
P
P
ANNOUNCE
button
I
K
P
S
ON/OFF
REVIEWING ANNOUNCEMENT
• Press and release ANNOUNCE button to
review your outgoing announcement.
11
TELEPHONE SETUP
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
SETTING THE DISPLAY LANGUAGE
1. Press and release PROG until
LANGUAGE
shows on the display.
2. Use the CID REVIEW buttons to change
the display to the desired language.
3. When finished, press and release PROG
again to store the setting and enter the
Area Code menu.
SETTING THE LOCAL AREA CODE
1. Press and release PROG until
CODE
shows on the display.
2. Use the keypad to enter the area code.
3. When finished, press and release PROG
again to store the area code and exit
setup.
NOTE: If you make a mistake, repeat steps 1-3.
NOTE: If you find it necessary to dial all
local calls with the area codes included,
press and release PROG, until SET AREA
CODE is displayed. Then enter "000". Press
PROG again to confirm.
SET
SET AREA
CID
REVIEW
buttons
PROG
button
12
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
CORDLESS PHONE BASICS
MAKING A CALL
The only two things you need to know to
make a call are:
• Press the TALK button before you dial.
• Press TALK button or place the handset in
the base to hang up.
Otherwise, it works just like any other
phone.
IMPORTANT: Because cordless phones
operate on electricity, you should have at
least one phone in your home that isn’t
cordless, in case the power in your home
goes out.
TALK
button
REDIAL
Press the REDIAL button to redial the last
number you called (up to 32 digits).
If you get a busy signal, and want to keep
dialing the number, press TALK to turn off
the phone. Press TALK again to turn it back
on. Then press REDIAL to dial the number.
REDIAL
button
13
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
RECEIVING A CALL
To answer a call you must press the TALK
button on the handset before you can talk.
FLASH
Use the FLASH button to activate custom
calling services such as call waiting or call
transfer, which are available through your
local phone company.
TIP: Don't use the TALK button to activate
custom calling services such as call waiting,
or you’ll hang up the phone.
TALK
button
VOLUME
When the phone is ON, press the VOL
VOL
button
buttons to adjust the volume of the
handset's earpiece. There are four settings.
MUTE
MUTE
button
Use the MUTE button to interrupt a phone
conversation to talk privately with someone
else in the room.
1. Press MUTE to activate mute feature. The
display shows
MUTE
.
2. Press MUTE again to turn it off.
14
FLASH
button
RINGER SWITCH
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
The RINGER switch must be ON for the
handset to ring during incoming calls.
FINDING THE HANDSET
This feature helps to locate a misplaced
handset.
Press the PAGE button on the base. The
display shows
beeps for about 4 minutes or until you
press TALK or ANSW on the handset.
NOTE: You can still page the handset with
the ringer off.
PAGING YOU
. The handset
TALK
button
RINGER switch
PAGE button
CORDLESS TELEPHONE
900 MHz
DIGITAL ANSWERER
DAY/
CHECK
HOUR MIN
PAGE
15
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
CALLER ID FEATURES
This unit receives and displays information
transmitted by your local phone company.
This information can include the phone
number, date, and time; or the name,
phone number, date, and time. The unit can
store up to 40 calls for later review.
CALLER ID WITH CALL WAITING
Provided you subscribe to Caller ID with
Call Waiting service from your phone
company, you are able to see who is calling
when you hear the call waiting beep. The
caller identification information appears in
the display after you hear the tone.
• Press the FLASH button to put the
current person on hold so that you can
answer the incoming call.
RECEIVING AND STORING CALLS
When you receive a call, the information is
transmitted by the phone company to your
Caller ID Telephone between the first and
second ring.
CHANNEL
button
TALK
button
REDIAL
button
FLASH
button
VERY IMPORTANT: The Caller ID feature
of this product requires a subscription to
Caller ID service from your telephone
company.
16
When the memory is full, a new call automatically replaces the oldest call
in memory.
been reviewed.
NEW
appears in the display for calls received that have not
NOTE: Check with your local
phone company regarding
name service availability.
Time
10:51
A.M.
Date
8/11
NEW
REPT
Number of calls
CALL
#
MEMO
25
317-555-4231
SMITH JOHN
Caller ID name
REVIEWING MESSAGES
As calls are received and stored, the display
is updated to let you know how many calls
have been received.
• Press the CID REVIEW arrow down
button to scroll through the call records
from the most recent to the oldest.
• Press the CID REVIEW arrow up button to
scroll through the call records from the
oldest to the newest.
Caller ID phone number
17
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
DELETING RECORDS
Use the DELETE button to erase the record
currently shown in the display or all
records.
DELETING THE CURRENT RECORD
Press DELETE. The display shows
DELETED
.
DELETING ALL RECORDS
1. Press and hold DELETE. The display
shows
DELETE ALL?
2. Press DELETE again to erase all records.
DIALING A CALLER ID NUMBER
1. Make sure the phone is OFF.
2. Use the CID REVIEW buttons to display
the desired Caller ID record.
3. Press the DIAL button to dial the number.
18
CID
REVIEW
buttons
DIAL
button
DELETE
button
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
CHANGING THE NUMBER FORMAT
The FORMAT button lets you change the
format of the displayed number. The
available formats are as follows.
7-digit 7-digit telephone number.
10-digit 3-digit area code + 7-digit
telephone number.
11-digit long distance code “1” + 3-digit
area code + 7-digit telephone
number.
1. Use the CID REVIEW buttons to scroll to
the number you want to call back.
2. If the number will not dial as shown,
press the FORMAT button. Repeat if
necessary, until the correct number of
digits are shown.
3. Press DIAL.
NOTE: If you find it necessary to dial all
local calls with the area codes included,
press and release PROG, until SET AREA
CODE is displayed. Then enter "000". Press
PROG again to confirm.
FORMAT
button
CID
REVIEW
buttons
DIAL
button
PROG
button
19
MEMORY
Store up to ten 24-digit numbers in
memory for quick dialing. This memory
feature is in addition to the 40 Caller ID
records that can be stored in memory.
STORING A NUMBER IN MEMORY
The phone must be OFF when you store
numbers.
1. Press the MEM button.
2. Press the memory location number (0-9).
3. Press MEM again. The display shows
ENTER NAME.
4. Use the keypad to store a name (up to 16
characters). More than one letter is
stored in each of the number keys. For
example, to enter Joe Smith, press 5 for
J; press 6 three times for O; press 3 two
times for E; press 1 to enter a space
before you start entering the last name;
press 7 four times for S; press 6 for M;
press 4 three times for I; press 8 for T;
FORMAT MUTE
PAUSE
REDIAL MEM
PLAY/STOP SKIPREVIEW
4
PQRS
7
TONE
*
CHANNEL FLASHINT
PROG
DELETEDIAL
TALK
DEF
ABC
21
TUV
8
ERASE
OPER
0
ANSW
MEM
3
button
MNO6JKL5GHI
WXYZ
9
#
NOTE: If you don't want to enter the
name, skip step 4.
20
and 4 two times for H. If you're using two
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
letters consecutively that are stored in
the same number key, you must press
FORMAT between the letters. For example, if you enter Barb, press 2 two
times for B; press FORMAT; press 2 for A;
7 three times for R; and 2 two times for
B. You need to press FORMAT between
the B and the A since they are stored
within the same number key.
5. Press MEM. The display shows
TEL NUMBER
.
6. Use the keypad to enter the number you
ENTER
FORMAT
button
want to store (up to 24 digits).
7. Press MEM again to store the number.
8. Record whose number is stored in the
location on the memory label provided.
You will also be able to view the name
and number in the phone's display.
CHANGING A STORED NUMBER
Use the same procedure to change a stored
number as you do to store a number—
you’re just replacing the phone number
with a different one.
MEM
button
21
DIALING A STORED NUMBER
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
1. Make sure the phone is ON by pressing
the TALK button.
2. Press MEM.
3. Press the number (0-9) for the desired
memory location. The number dials
automatically.
OR
1. Make sure the phone is OFF.
2. Press MEM.
3. Use the CID REVIEW buttons to scroll
through the numbers stored in memory
until the desired number is shown.
4. Press DIAL. The number dials
automatically.
IMPORTANT: If you make test calls to
emergency numbers stored in memory,
remain on the line and briefly explain the
reason for the call to the dispatcher. Also,
it’s a good idea to make these calls in
off-peak hours, such as early morning or
late evening.
TALK
button
CID
REVIEW
buttons
DIAL
button
MEM
button
22
CHAIN DIALING FROM MEMORY
Use this feature to make calls which require a sequence of numbers such
as using a calling card for a frequently called long distance number.
Basically, you dial each part of the sequence from memory. The following
example shows how you can use chain dialing to make a call through a
long distance service:
The Number For Memory Location
Long distance access number 7
Authorization code 8
Frequently called long distance number 9
1. Make sure the phone is ON.
2. Press MEM and then press 7.
3. When you hear the access tone, press
MEM and then press 8.
4. At the next access tone, press MEM and
then 9.
TIP: Wait for the access tones before
pressing the next memory button, or your
call might not go through.
TONE
CHANNEL FLASHINT
FORMAT MUTE
TALK
PAUSE
REDIAL MEM
PLAY/STOP SKIPREVIEW
ABC
4
TUV
PQRS
7
ERASE
OPER
*
ANSW
PROG
DELETEDIAL
DEF
3
21
8
0
MEM
button
MNO6JKL5GHI
WXYZ
9
#
23
INSERTING A PAUSE IN THE
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
DIALING SEQUENCE
Press the REDIAL button to insert a delay
in the dialing sequence of a stored
telephone number when a pause is needed
to wait for a dial tone (for example after
you dial 9 for an outside line, or to wait for
a computer access tone). Each pause
counts as 1 digit in the dialing sequence.
CID
REVIEW
buttons
REVIEWING AND DELETING
DELETE
button
STORED NUMBERS
1. Press MEM.
2. Use the CID REVIEW buttons to scroll to
the desired memory location or press 0-9.
3. While the entry is displayed, press
DELETE to delete the entry. The display
shows
24
DELETED.
REDIAL
button
MEM
button
ADVANCED FEATURES
WXYZ
9
TUV
8
PQRS
7
MNO
6
JKL5GHI
4
DEF
3
ABC
21
#
OPER
0
TONE
*
CHANNEL FLASHINT
REDIAL MEM
DELETEDIAL
FORMAT MUTE
PROG
PAUSE
TALK
ANSW
ERASE
PLAY/STOP SKIPREVIEW
CHANNEL BUTTON
While talking, you might need to manually
change the channel in order to reduce static
caused by baby monitors, garage door
openers, or other cordless phones. Press
and release the CHANNEL button to
advance to the next clear channel.
TEMPORARY TONE
This feature enables pulse (rotary) service
phone users to access touch-tone services
offered by banks, credit card companies,
etc. Press the TONE button to temporarily
make the phone touch-tone compatible. To
get information about your bank account,
for example, you would:
1. Call the bank’s information line.
2. Press the TONE key, denoted with (*) on
the keypad, when your call is answered.
3. Follow the voice menu instructions to get
the information. When you hang up, the
phone goes back to pulse (rotary) service.
TONE
button
CHANNEL button
25
ANSWERING MACHINE OPERATION
This section discusses the buttons
and features on the answering machine.
MESSAGES INDICATOR
The MESSAGES indicator shows you how
many new messages you have. The
ANSWER ON/OFF button must be on in
order for the MESSAGES indicator to work.
MESSAGES indicator
MESSAGES
8.8.
CHARGE/
IN USE
SCREENING CALLS FROM
BASE
THE
You can screen incoming calls by waiting for
the caller to begin leaving a message (to
hear who it is), then pick up the handset,
and press TALK to talk to the caller. The
answering machine automatically stops
recording when you activate the handset or
pick up an extension phone.
TIP: Make sure the volume on the base is set
loud enough to hear your incoming calls.
REVIEW
button
ANNOUNCE
S
/
T
Y
O
A
L
P
P
ANSWER
ON/OFF
button
NEXT
I
E
V
W
E
R
ERASE ANSWER
PLAY/
STOP
button
MEMO
I
K
S
ON/OFF
P
SKIP
button
26
MESSAGE PLAYBACK
The messages indicator lets you know when you have messages. To play
messages, press PLAY/STOP.
While a message is playing, you can do the following:
• Press PLAY/ STOP to stop the message playback.
• Press and release REVIEW to restart the current message; continue to
press and release REVIEW to go to previous messages.
• Press and release SKIP to go to the next message.
• Press PLAY/ STOP to stop message playback.
MEMORY FULL
When the memory is full, the system answers after 10 rings. You need to
erase some messages so the answerer can record new messages.
ERASING MESSAGES
You can erase messages three ways: one message at a time using the
ERASE button on the base; all messages using the ERASE button on the
base; or one message at a time using the ERASE button (0) on the handset
or a phone in another location.
• To erase a message, press PLAY/STOP on the base and press and
release ERASE button on the base to erase the message that is playing.
• To erase all messages, press and hold the ERASE button on the base
until the unit beeps when messages have stopped playing.
27
• To erase a message from the handset:
1. Press ANSWER button on the handset.
2. Press PLAY/STOP on the handset (the 2 button).
3. Press ERASE on the handset (the 0 button) to erase the
message that is playing.
NOTE: Erased messages cannot be restored. Also, be careful you don't press
ERASE button as the next unheard message is playing because that message
will also be erased.
LEAVING A MEMO
Use the Memo feature to leave a message.
1. Press and hold the MEMO button. You need to hold the button until you
finish the message.
2. Begin talking after you hear the beep.
3. Release the MEMO button when you finish.
28
REMOTE ACCESS
This section explains two types of remote
access: using the handset to access the
answering machine and accessing the
answering machine from another phone.
The handset contains integrated buttons
that enable you access the answering
machine with the handset.
You can also access your answering
machine from any phone that is tone-dial
compatible by entering a 3-digit security
code after you hear the outgoing
announcement. A voice menu system
guides you through all of the procedures.
29
Loading...