GBC COMBPRO1000 User Manual
SAFETY MESSAGES
Your safety as well as the safety of others is important to
GBC. In this Operator Manual and on the product are important safety messages. Read these messages carefully.
A The safety alert symbol precedes each safety message
in this Operator Manual. This symbol indicates a
potential personal safety hazard that could hurt you or
others. as well as cause product or property damage.
The following warning is found on this unit:
This safety message means you could be seriously hurt or
killed if you open the product and expose yourself to
hazardous voltage.
The following symbols appear on this product, and their
meanino is as follows:
E!3PU-NCH
A WARNING: For your protection, do not connect the
CombPRO 1000 to electrical power until you read
these instructions completely. Keep these instructions in a
convenienIlocation for future reference. To guard against
injury, the following basic safely precautions must be
observed in the set-up and use of this product.
IMPORTANTSAFEGUAROS
GENERALSAFEGUAROS
.Use the CombPRO 1000 only for its intended purpose of
punching and binding paper and covers according to fhe
indicated specifications.
.Do not place anything in the punch opening of the machine
other than paper and cover stock.
.Place unit on a secure, stable work area to prevenlIhe
machine falling and possibly causing personal injury and
damage to the unit.
.Follow all warnings and instructions marked on the product.
.Lift the machine from the bottom, nollhe cover.
.Do nolliflIhe machine by the cover or paper holder wire.
ELECTRICAL SAFEGUARDS
The CombPRO 1000 must be connected to a supply voltage
corresponding to the electrical rating of the machine as indicated on the serial/rating plate or in this manual.
i\ CAUTION: THE POWER RECEPTACLE MUST BE LOCATED
...NEAR THE EQUIPMENT AND BE EASILY ACCESSIBLE.
A CAUTION: IN CASE OF EMERGENCY, USE THE POWER
CORD AS A MAIN OISCONNECT DEVICE!
.Unplug the CombPRO 1000 before moving it, or when it is
not In use for an extended period of time.
.Do not operate with a damaged supply cord or plug, after it
malfunctions, or after it has been damaged in any manner.
.Do not overload electrical outlets beyond their capacity as
this can result in fire or electrical shock.
.Do not alter attachment plug. Plug is configured for the
appropriate electrical supply.
.The unit is intended for indoor use only.
.Never push objects into this product through cabinet slots.
Do not spill liquid of any kind on this product.
.Do not operate if the product has been exposed to rain or
water.
SERVICE
Do not attempt to service or repair the CombPRO 1000 your-
self. Unplug the unit and contact an authorized GBC service
representative for exchange or repair.
CLEANING
A CAUTION: Unplug this product before cleaning.
Wipe exterior only with a damp cloth. Do not use detergents
or solvents.
The following notes apply only to the units rated 230V 50Hz.
MAIN CORDSET SELECTION (FOR 230VAC MACHINES ONLY)
When choosing a detachable line cord for use with the
CombPRO 1000, always observe the following.
The cordset consists of three components; the attachment
plug, cordage and appliance inlet. Each of these components
must meet European regulatory approvals tor safely.
The following minimum electrical ratings for the specific
cordset are published for safely purposes. DO NOT USE
CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM
ELECTRICAL REQUIREMENTS.
PLUG: 3A, 250 volts, 50/60 Hz, Class 1,3 conductor,
European safely agency approved.
CORDAGE: Type H05W-F3GO.75, Harmonized ( <j HAR t> ).
The" <j 1:>" symbols indicate cordage approved to appropriate European standard (NOTE: "HAR" may be substituted
by the approval mark of the European safely agency which
approved the cordage. An example would be" <jVDE t>".
APPLIANCE CONNECTOR: 3A, 250 volts, 50/60 Hz, European
safely approved, Type IEC 320. Cordset shall not exceed 3
meters in length. Cordset with component electrical ratings
greater than the minimum specified electrical ratings may be
substituted.
3
Loading...