GBC 7500S, 7550X User Manual
SHREDDERS
7500S
7550X
1
EnglishFrançais
IMPORTANT
To quickly and easily confirm your warranty, register your new
shredder online at www.gbcconnect.com
IMPORTANTE
Para confirmar su garantía rápida y fácilmente,registre su nueva
trituradora en línea en www.gbcconnect.com
IMPORTANT
Pour confirmer votre garantie rapidement et facilement, enregistrez
votre nouveau déchiqueteur en ligne à www.gbcconnect.com
Español
2
Important Safety Instructions
Your safety as well as the safety of others is important to GBC. In this instruction
manual and on the product are important safety messages. Read these
messages carefully.
The safety alert symbol precedes each safety message in this instruction
manual and on the product. This symbol indicates a potential personal
safety hazard that could hurt you or others, as well as cause product or
property damage. Do not connect this unit to electrical power or attempt
to operate it before you have read these operating instructions. Save these
instructions for later use.
The following warning is found on the bottom of the product:
This safety message means that you could be
seriously hurt or killed if you open the product and
expose yourself to hazardous voltage.
The following warning is found inside of the cabinet door:
This safety message means that you could be
seriously hurt if you place your hands in the discharge
area.
This means don’t reach into the feed opening of the cutting head. This
could hurt you.
This means you should be careful because long hair can become
entangled in the cutting head. This could hurt you.
This means be careful of ties and other loose clothing which could
become entangled in the cutting head. This could hurt you.
This means you should be careful of loose jewelry which could become
entangled in the cutting head. This could hurt you.
This means do not allow children to use the shredder.
ELECTRICAL SAFEGUARDS
Unplug your shredder before moving it, emptying the bag, or when it is
•
not in use for an extended period of time.
Do not operate with a damaged power supply cord or plug, after it
•
malfunctions, or after it has been damaged in any manner.
Do not overload electrical outlets beyond capacity as this can result in
•
fire or electrical shock.
The socket-outlet should be installed near the equipment and shall be
•
easily accessible.
Do not alter attachment plug. Plug is configured for the appropriate
•
electrical supply.
Do not use near water.
•
Keep out of the reach of children.
•
Do not use extension cords to connect this product to the power supply.
•
3
English
SERVICE
Do not attempt to service or repair the unit yourself. If your shredder should
require service, contact your local dealer or call GBC National Service at
800-790-7787. Please have the model and serial number of your shredder
ready when calling.
4
Figure 1. The door must be closed
when operating the shredder.
Figure 1.
Figure 2. Keep the area around the
electrical outlet clear.
Unplug the shredder before cleaning
it.
Do not perform any repairs on the
shredder. (See page 12).
120V / 120A min.
Figure 2.
Figure 3.
Figure 3. Do not shred CDs or DVDs
in the cross cut model (7550X). It may
splinter disks and kick them back out.
Only the straight cut model (7500S) is
suitable to destroy CDs or DVDs.
Do not attempt to shred paper clips
with the cross cut model.
Figure 4.
5
Figure 4. Do not operate the
shredder without the safey guard
in place.
English
Figure 5. The shredder turns off
after one hour of inactivity. Turn
the power switch off when not in
use for extended times.
Figure 5.
A
2.
1.
6
Set Up
Figure 6.
ASSEMBLY
Figure 6.
Plastic Bag
1.
Pull out the waste receptacle
a.
frame and remove the round
belt from around the frame.
Insert the included plastic bag
b.
through the pull-out frame and
fold the top of the bag over the
frame.
Secure the bag with the round
c.
belt.
Slide the waste receptacle in
d.
and close the cabinet door.
Oiler
2.
Hook the oiler holder over the
a.
edge of the cabinet.
Remove the sticky tape from
b.
the oil tube.
Remove the cap from the oil
c.
bottle, insert the oil tube into
the bottle, and tighten the cap.
Place the oil bottle in the holder.
d.
The oil bottle has a fill level indication
(A).
Figure 7. Plug cord into the electrical
outlet.
Keep the area in front of the outlet
clear for easy access.
Figure 7.
A
A
B
Operation
OILER
Figure 8. When using for the
first time or when the oil bottle
is changed:
Press until the EMPTY LED
•
(A) no longer blinks red.
7
English
Figure 8.
Figure 9.
Figure 9. Flashing INJECT LED:
Indicates cutting shafts are
•
being automatically oiled.
Flashing EMPTY LED:
Indicates oil bottle is empty.
•
8
A
2.
1.
OPERATING THE SHREDDER
Figure 10.
Press the forward button to turn
1.
the shredder on. The green light
shows that the shredder is ready to
operate.
Feed paper in to the middle of the
2.
the throat. An auto sensing photo
cell detects the paper and starts
the machine. The shredder stops
automatically when no more paper
is inserted.
STANDBY MODE
After one hour of inactivity, the
shredder goes into standby and the
green LED turns off. Repeat step 1
above to turn the shredder back on.
Figure 10.
Figure 11.
SHEET CAPACITY INDICATOR
Figure 11.
The shredder has an ECC (electronic
capacity control) which indicates the
sheet capacity being used during
shredding (A).
Red LED (A).
The shredder stops automatically if
too much paper is inserted. The paper
is reversed.
Yellow LED (B).
Maximum sheet capacity during
shredding.
Green LED (C).
Normal capacity during shredding.
Figure 12.
Figure 12. Shredder stops
automatically when door is opened
and a red LED indicator lights.
Figure 13. The shredder stops
automatically when the plastic bag
is full. Empty the bag when the “bag
full” yellow indicator lights.
(
See page 6).
9
English
Figure 13.
10
Figure 14. The shredder stops
automatically when too much paper
is inserted at the same time. The
shredder features an automatic
reverse function that will be activated
when too much paper has been
inserted.
Figure 14.
Figure 15. If necessary, when a paper
jam occurs and the automatic reverse
function does not clear all of the
paper, press the reverse button to
reverse the cutting unit and release
the paper.
Figure 15.
Note: The auto sensing photo cell
must not be obstructed.
Once the shredder is clear, re-insert
smaller quantities of paper.
Figure 16.
11
Figure 16. The shredder
automatically stops if the safety
guard (A) is opened (symbol
flashes ). Close the safety guard
to shred paper. To remove any
paper debris from a paper jam,
the machine runs for a short time
in reverse with the safety guard
open. If required, press the reverse
button several times.
English
12
A
B
Troubleshooting
Symptom Corrective Action
Machine will not start. Plug unit in.
Switch unit to Power On by pressing the forward
button (green LED lights).
Feed paper in to the center of the feed opening
where the auto sensing photo cell is located.
Close the cabinet door.
Empty the shred bag.
Close safety guard.
Bag full indicator lights
but bag is not full.
Figure 17.
Unplug unit from electrical outlet.
Remover paper debris between the cutting head
from below with a brush (not included). Figure 18.
Figure 18.
Figure 17.
Symptom Corrective Action
Machine will not stop. Unplug unit from electrical outlet.
Clean the auto sensing photo cell with a small
brush (not included). Figure 19.
Machine stops. Overload protection. Allow unit to cool down
approximately 5 to 10 minutes.
Symbol flashes
•
When symbol stops flashing, machine is
•
ready for operation.
13
English
Figure 19.
If none of the troubleshooting actions correct the problem, contact your local
dealer or call GBC National Service at 1-800-790-7787.
14
Accessories
Environmentally safe oil 33.8 oz. (1 litre)
Part number 1753190
Shredder bags for models 7500S and 7550X (100 bags)
Part number 1145482
To order, visit www.gbcconnect.com or call 1-800-723-4000.
Loading...