Page 1
640t Laminator
INSTALLATION &
OPERATION MANUAL
Document Number: 04048E001
Do not duplicate without written permission.
Page 2
The information in this publication is provided for the
use of GBC customers. General Binding Corporation
(GBC), and it’s parent ACCO Brands Corporation, make
no guarantees or warranties in connection with this
publication. ACCO and GBC expressly disclaim any
liability for errors in this publication or for incidental or
consequential damage in connection with the furnishing
or use of the information in this publication, including,
but not limited to, any implied warranty of tness or
merchantability for any particular use.
GBC and ACCO, reserve the right to make changes to this
publication and to the products described in it without
notice. Reference in this publication to information or
products protected by copyright or patent does not imply
or convey any rights or license there under.
The information contained in this publication may not be
reproduced, stored, transmitted, or transferred, in whole
or in part, in any form without the prior and express written
permission of ACCO Brands Corporation.
640t – Installation and Operating Instructions
Page 3
640t – Installation and Operating Instructions
Ta b l e o f Co n T e n T s
1. Safety
Warnings .................................................................1-1
General ....................................................................1-1
Electrical ..................................................................1-2
2. Warranty
Limited 90-Day Warranty ........................................2-1
For European Union Residents Only .......................2-1
3. Specifications
Specications ..........................................................3-1
FCC Note ................................................................ 3-2
Canada Class A Notice - Avis Canada, Classe A . 3-2
Modications .......................................................... 3-2
4. Installation
Prior to Installation ................................................. 4-1
Installation .............................................................. 4-1
5. Feature guide
Film Shafts ............................................................. 5-1
Idler Bars ................................................................ 5-2
A. Upper Idler ....................................................... 5-2
B. Lower Idler ....................................................... 5-2
Rollers and Safety Sensor ..................................... 5-2
A. Upper Main Roller ............................................ 5-2
B. Lower Main Roller ............................................ 5-2
C. Safety Sensor .................................................. 5-2
Emergency Stop and Table .................................... 5-3
A. Table Interlock Hole ........................................ 5-3
B. Table Interlock ................................................5-3
C. Emergency Stop .............................................. 5-3
D. Front Feed Table .............................................. 5-3
Control Panel and Print Clamp ..............................5-3
A. Control Panel & Display ...................................5-3
B. Print Clamp Lock Release Latch ..................... 5-3
Tension Controls .................................................... 5-4
A. Release Liner Tension Knob ............................ 5-4
B. Upper Film Tension Knob and Brake ..............5-4
C. Media Rewinder Tension Knob ....................... 5-4
D. Lower Film Tension Knob and Brake ...............5-4
Roller Pressure Handle .........................................5-4
A. Mounting & Laminating Presets ...................... 5-4
B. Roller Pressure Handle .................................... 5-4
Media Core Adapter ..............................................5-5
Rewinder ................................................................ 5-5
A. Rewinder Core Adapters .................................5-5
B. Rewinder Shaft ................................................ 5-5
C. Rewinder Cardboard Tube ..............................5-5
D. Core Chucks ....................................................5-5
E. Unwind/Supply Shaft ....................................... 5-5
Power ..................................................................... 5-6
A. On/Off Power Switch ....................................... 5-6
B. Circuit Breaker ................................................. 5-6
C. Nomenclature Plate ......................................... 5-6
Power Cord and Foot Switch .................................5-6
A. Power Cord ...................................................... 5-6
B. Foot Switch ...................................................... 5-6
Control Panel .......................................................... 5-7
Temp Section ....................................................... 5-7
Speed Section ..................................................... 5-7
6. Operation
General Operation .................................................. 6-1
Loading Film ........................................................... 6-2
Removing and Installing the Print Clamp ............ 6-3
Removing and Installing the Feed Table .............. 6-3
Loading Film Onto the Supply Shafts ..................6-4
Threading Film with a Threading Card ................. 6-5
Loading Film by Tacking New Film to Existing Film 6-7
Decaling in Two Passes .........................................6-8
Mounting ................................................................ 6-9
Tips For Threading Pressure Sensitive Adhesive .....
(PSA) Film ............................................................. 6-9
Pre-Coating Boards ............................................. 6-9
Mounting Only ...................................................... 6-9
Film Alignment and Tension ..................................6-10
Film Alignment ....................................................6-10
Film Tension ........................................................6-10
Clearing a Film Jam (Wrap-up) ...........................6-11
Lamination Guide .................................................6-12
7. Operator Maintenance
Caring for the 640t Laminator .................................7-1
Cleaning The Rollers .............................................7-1
Troubleshooting ......................................................7-2
Notes .......................................................................7-3
Page i
Page 4
640t – Installation and Operating Instructions
Page ii
Page 5
640t – Installation and Operating Instructions
ADVERTENCIA
!
Riesgo de choque
eléctrico
No abra:
Adentro no hay
piezas reparables
por el usuario.
Mantenimiento
solamente por
personal calificado.
ATTENTION
!
Risque de
secousse
électrique.
Ne pas ouvrir:
Pas de pièces
réparables par
l'utilisateur.
Entretien
seulement par
personnel qualifié.
WARNING
!
Electrical shock
hazard.
Do not open.
No user
serviceable
parts inside.
Refer servicing to
qualified service
personnel.
CAUTION
AT TENTION
CUIDADO
PUNTO DE
PINCHAMIENTO
Keep hands and
fingers away.
Mantener manos y
dedos a distancia.
Tenir mains et
doigts a l'écart.
PINCH POINT
between rollers.
POINT DE
PINCEMENT
entre les rouleaux.
entre rodillos.
1. sa f e t y
Your safety, as well as the safety of others is
important. Before you install or use the machine,
read and follow all the safety notices carefully in
this chapter. In this instruction manual, and on the
laminator, you will nd important safety notices
regarding the laminator. Read all of the instructions
and save these instructions for further use.
The safety alert symbol precedes each
safety notice in this manual. The symbol indicates a
potential personal safety hazard to you or others, as
well as laminator or property damage.
This safety alert symbol indicates a potential
electrical shock. It warns you to not open the
laminator and expose yourself to hazardous voltage.
The following warnings are found on the 640t
laminator.
This safety notice means that you could be seriously
hurt or killed if you open the laminator and expose
yourself to hazardous voltage.
Wa r n i n g s
Do not attempt to service or repair the •
laminator.
Do not connect the laminator to an electrical •
supply or attempt to operate the laminator
until you have completely read these
instructions. Maintain these instructions in a
convenient location for future reference.
To guard against injury, the following safety •
precautions must be observed when installing
and using the laminator.
Failure to observe these warnings could result in
severe bodily damage or death.
ge n e r a l
Keep hands, long hair, loose clothing, and •
articles such as necklaces or ties, away from
the front of the rollers to avoid entanglement
and entrapment.
Do not use the laminator for other than its •
intended purpose.
Do not place the laminator on an unstable •
cart, stand or table. An unstable surface may
cause the laminator to fall resulting in serious
bodily injury. Avoid quick stops, excessive
force and uneven floor surfaces when moving
the laminator.
Do not defeat or remove electrical and •
mechanical safety equipment such as
interlocks, shields and guards.
Do not insert objects unsuitable for lamination •
or expose the equipment to liquids.
This safety notice means that your ngers and hands
could be trapped and crushed in the rollers. Clothing,
jewelry and long hair could be caught in the rollers
and pull you into them.
Page 1-1
Page 6
el e c t r i c a l
The laminator should be connected only to a source
of power as indicated in these instructions and on
the serial plate located on the rear of the laminator.
Contact an electrician should the attachment
plug provided with the laminator not match the
receptacles at your location.
WARNING: Do not attempt to service or repair
the laminator. Failure to observe this warning could
result in severe personal injury or death.
Disconnect the plug from the receptacle and contact
your dealer or distributor when one or more of the
following has occurred.
The power supply cord or attachment plug is •
damaged.
Liquid has been spilled into the laminator.•
The laminator is malfunctioning after being •
mishandled.
The laminator does not operate as described •
in these instructions.
640t – Installation and Operating Instructions
CAUTION: The receptacle must be located
near the equipment and easily accessible.
Disconnect the attachment plug from the receptacle
to which it is connected and keep the power supply
cord in your possession while moving the laminator.
Page 1-2
Page 7
640t – Installation and Operating Instructions
2. Wa r r a n t y
li m i t e d 90-da y Wa r r a n t y
GBC warrants to the original purchaser for a
period of ninety days on labor and on parts after
installation that this laminator is free from defects
in workmanship and material under normal use and
service. GBC’s obligation under this limited warranty
is limited to replacement or repair, at GBC’s option,
of any part found defective by GBC without charge
for material or labor.
This product may have additional service coverage.
Please see your invoice for information on length of
any additional coverage or call your local service
center for more information.
THIS LIMITED WARRANTY IS IN LIEU OF
ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED. WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR
PURPOSE ARE EXPRESSLY EXCLUDED.
ANY REPRESENTATIONS OR PROMISES
INCONSISTENT WITH, OR IN ADDITION TO, THIS
LIMITED WARRANTY ARE UNAUTHORIZED
AND SHALL NOT BE BINDING UPON GBC. IN
NO EVENT SHALL GBC BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER OR NOT FORESEEABLE.
This limited warranty shall be void if the laminator
has been misused; mishandled; damaged by
negligence, by accident, during shipment, or due to
exposure to extreme conditions; repaired, altered,
moved, or installed by anyone other than GBC or
its authorized agents; or if incompatible lm was
used. GBC’s obligation under this limited warranty
does not include routine maintenance, cleaning,
adjustment, normal cosmetic or mechanical wear, or
freight charges.
Without limiting the generality of the previous
paragraph, GBC’s obligation under this limited
warranty does not include:
Damage caused to the rollers by knives, razors, 1.
or other sharp tools: by any foreign objects
falling into the working area of the laminator;
or by cleaning the laminator with solutions or
materials that harm its surfaces;
Damage caused by adhesives; nor 2.
Damage caused by lifting, tilting or attempting to 3.
position the laminator other than rolling it on its
castors across an uneven surfaces.
FOR EUROPEAN UNION RESIDENTS ONLY: This
guarantee does not affect the legal rights which
consumers have under applicable national legislation
governing the sale of consumer goods.
Page 2-1
Page 8
640t – Installation and Operating Instructions
Page 2-2
Page 9
640t – Installation and Operating Instructions
3. spec ifications
640t
Maximum film roll diameter 5 inches
Operating Speed
Variable•
Fixed•
Dimensions
Width•
Height•
Depth•
Weight•
Electrical Requirements
Voltage•
Current•
Power•
U.S. Receptacle•
*NOTE: The 640t laminator has a xed speed in reverse or when using the foot pedal with the feed table removed.
3 to 16 fpm (0.8 to 4 m)
3 fpm (0.9 m)*
78 in (198 cm)
48 in (122 cm)
30 in (76 cm)
350 lbs. (273 kg)
220 VAC 60 Hz
9 Amps
2000 W
NEMA 6-15R
Height
Depth
Width
Fig. 3-1. 640t Dimensions (Shown in Inches (cm).)
Page 3-1
Page 10
640t – Installation and Operating Instructions
fcc no t e
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when the equipment
is operated in a commercial environment. This
equipment generates, uses, and can radiated radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
ca n a d a cl a s s a no t i c e - av i s
ca n a d a , cl a s s e a
This Class A digital apparatus complies with
Canadian ICES-003.
(Cet appareil numérique de las Classe A est
conforme a la norme NMB-003 du Canada.
mo d i f i c a t i o n s
Any modications made to this device that are not
approved by General Binding Corporation, an ACCO
Brands Corporation, may void the authority granted
to the user by the FCC and/or by Industry Canada to
operate this equipment.
Toutes modications apportées à ce dispositif et
non approuvées par General Binding Corporation,
an ACCO Brands Corporation annuleront le droit
accordé à l’utilisateur par le FCC et/ou par Industrie
Canada de faire fonctionner cet équipement
Page 3-2
Page 11
640t – Installation and Operating Instructions
4. in s t a l l a t i o n
This chapter describes how to install the machine.
There are no operator serviceable parts to the
machine other than periodic cleaning. Refer to
“7. Operator Maintenance” on page 7-1.
WARNING: Do not attempt to service or repair
the laminator. Failure to observe this warning could
result in severe personal injury or death.
Disconnect the plug from the receptacle and contact
your dealer or distributor when one or more of the
following has occurred.
The power supply cord or attachment plug is •
damaged.
Liquid has been spilled into the laminator.•
The laminator is malfunctioning after being •
mishandled.
The laminator does not operate as described •
in these instructions.
pr i o r t o in s t a l l a t i o n
in s t a l l a t i o n
To set up the laminator for the first time:
Place the laminator on a stable flat surface 1.
capable of supporting the weight of the machine.
An additional work surface near the laminator is
recommended for items to be laminated.
The laminator should be located so that when 2.
not using the rear rewind, exiting film drops freely
to the floor or to a table that is lower than the exit
point of the laminator. Accumulation of laminate
immediately behind the laminator as it exits the
equipment may cause the film to wrap around
the rollers, jamming the machine.
Avoid locating the laminator near sources of heat 3.
or cold. The laminator should not be in the direct
path of forced heated or cooled air.
Connect the attachment plug provided with the 4.
laminator to a suitably grounded outlet only.
Inspect the package for damage. Shipping damage
should be brought to the immediate attention of the
delivering carrier.
Page 4-1
Page 12
640t – Installation and Operating Instructions
Page 4-2
Page 13
640t – Installation and Operating Instructions
5. fe a t u r e g u i d e
This chapter helps you identify the main components of the laminator.
Pressure roller
Safety sensor
Feed table
Feed table
interlock latch
(under table)
Bottom supply shaft
Foot switch
Release liner take-up
Top lm supply shaft
Control panel
Roller pressure
handle
Fig. 5-1. Laminator Identication.
fi l m sh a f t s
A. Release Liner Take-up
Rewinds the release liner of pressure sensitive lms.
It consists of a shaft, core adapters, and cardboard
core.
B. Upper Unwind/Supply Shaft
Holds the upper medium supply on the laminator.
C. Lower Unwind/Supply Shaft
Holds the lower medium supply on the laminator.
Fig. 5-2 Take-up and Supply Shafts.
Page 5-1
Page 14
640t – Installation and Operating Instructions
id l e r Ba r s , un W i n d sh a f t s ,
re W i n d sh a f t s
Fig. 5-3. Idler Bars, Unwind Shafts, Rewind Shafts.
a. up p e r re W i n d
B. up p e r un W i n d /su p p ly sh a f t
ro l l e r s a n d sa f e t y se n s o r
Fig. 5-4 Upper and Lower Main Rollers and Safety Sensor.
a. up p e r ma i n ro l l e r
The Upper Main Roller lowers onto the Lower Main
Roller to create the nip or the point at which the top
and bottom rollers come into contact and the point
at which the items to be laminated are introduced to
the laminator.
c. lo W e r un W i n d /su p p l y sh a f t
The Lower Idler directs Kraft Paper or images to the
Lower Main Roller.
d. up p e r id l e r
The Upper Idler directs the lm around the roller and
is used as a point of release when using PSA lms.
The release liner will be separated and redirected to
the Rewinder.
The Upper Main Roller is heated. The •
temperature is controlled by the Control Panel.
The Upper Main Roller can be raised or •
lowered using the Roller Pressure Handle.
B. lo W e r ma i n ro l l e r
The Lower Main Roller is driven and advances media
into the nip. The Lower Main Roller is not heated.
c. sa f e t y se n s o r
Not shown: Lower Idler Bar and Lower Rear Rewind
The Safety Photo Sensor prevents entanglement,
entrapment, and inadvertent contact with the
rollers. The sensors are located on each side of the
machine, in front of the bottom roller. They stop the
machine when a hand or object blocks the invisible
beam if you are not using the foot switch.
When the foot switch is used, the speed drops to 3
fpm (0.9 m).
WARNING: Keep your ngers and hands
away from the nip point. Failure to observe
this warning could result in severe personal injury.
Page 5-2
Page 15
640t – Installation and Operating Instructions
em e r g e n c y st o p a n d ta B l e
Fig. 5-5. Emergency Stop Button and Table Components.
a. ta B l e in t e r l o c k ho l e
When the table is down, the latch engages this hole.
B. ta B l e in t e r l o c k
The Table Interlock latch locks the feed table into
position and activates an interlock switch. The latch
is located on the left, underside of the feed table.
Move the latch to the right to release the table. Then
lift the table upwards and away from the laminator.
c. em e r g e n c y st o p
co n t r o l pa n e l a n d pr i n t cl a m p
Fig. 5-6. Control Panel and Print Clamp
and Lock Release Latch.
a. co n t r o l pa n e l & di s p l a y
Allows the operator to control the speed and
temperature of the rollers.
B. pr i n t cl a m p lo c k re l e a s e la t c h
The Print Clamp helps keep prints against the feed
table while being fed into the rollers. Release the
Lock Release Latch when using mounting boards.
The Emergency Stop Switch is on the left side
of the 640t laminator. To engage, press the
Emergency Stop Switch and roller movement stops.
To disengage, turn the Emergency Stop Switch
clockwise once the emergency condition has been
resolved.
d. fr o n t fe e d ta B l e
The feed table is used to position items for
laminating and mounting. When the feed table is
removed, the laminator runs at 3 fpm (0.9 m) when
you press the foot switch. The feed table is removed
only when you load lm.
Page 5-3
Page 16
640t – Installation and Operating Instructions
te n s i o n co n t r o l s
Fig. 5-7. Tension Knobs and Brakes
a. re l e a s e li n e r te n s i o n kn o B
Use the Release Liner Tension Knob to increase and
decrease the amount of Pull that is being applied
to the release liner. This prevents the release liner
from being pulled into the laminator or the lm from
wrapping around the rewind tube.
ro l l e r pr e s s u r e ha n d l e
Fig. 5-8. Roller Pressure Handle.
a. mo u n t i n g & lam in ating pr e s e t s
Mounting and Laminating Presets are located on
the side cover. The decal describes the gap and
downward pressure.
B. ro l l e r pr e s s u r e ha n d l e
B. up p e r fi l m te n s i o n kn o B
a n d Br a k e
The Upper Film Tension Knob and Brake allows the
operator to increase or decrease the lm web tension
as needed to reduce curl and wrinkles.
c. me d i a re W i n d e r te n s i o n kn o B
The Media Rewinder Tension Knob allows the
operator to adjust the amount of pull on the nished
media.
d. lo W e r fi l m te n s i o n kn o B
a n d Br a k e
The Lower Film Tension Knob and Brake allows the
operator to increase or decrease the lm or media
web tension as needed to reduce curl and wrinkles.
The Roller Pressure Handle adjusts the amount of
roller pressure needed for various laminating and
mounting applications. Pull the handle away from the
laminator, rotate it to the desired pressure, and press
it into the desired slot. Three main function settings
are provided.
IMPORTANT: Use a pressure setting that is
appropriate for the material you are laminating or
mounting.
Release – Provides the widest opening of 1/2 in. (1.6
to 12.7 mm) between the pressure rollers and takes
pressure off the rollers. This is used when installing
new rolls of lm. When the machine is not in use, put
the handle in this position.
Mounting – Used when bonding to a rigid substrate
such as mounting boards. Thickness range is 1/16 to
1/2 in. (1.6 to 12.7 mm).
Laminating – Used to adhere materials in multiple
substrates. The two positions are low (right) and high
(left) pressure.
Page 5-4
Page 17
640t – Installation and Operating Instructions
me d i a co r e ad a p t e r
Fig. 5-9. Media Core Adapter.
The Media Core Adapters hold and lock the rolls of
lm and release liner on the shafts to prevent side to
side shifting. Grippers on the Core Adapters ensure
proper tension on the lm. The Supply Shaft Core
Adaptors lock in place with a set screw. The release
liner take-up Core Adaptors are held in place by
friction.
re W i n d e r
Fig. 5-10. Rewinder Components.
a. re W i n d e r co r e ad a p t e r s
The Rewinder Core Adapters are held in place
using friction. They adapt to the provided 2-1/4 inch
cardboard tube and most media tubes.
B. re W i n d e r sh a f t
The Rewinder Shaft supports the Rewinder Core
Chucks and tube.
c. re W i n d e r ca r d B o a r d tu B e
The Rewinder Cardboard tube carries the release
liner and media.
d. co r e ad a p t o r s
The Core Adaptors hold lm and media.
e. un W i n d /su p p l y sh a f t
The Unwind/Supply Shaft holds lm and media.
Page 5-5
Page 18
640t – Installation and Operating Instructions
po W e r
Fig. 5-11. Power Panel.
a. on/of f po W e r sW i t c h
The On/Off Power Switch is located at the back of
the machine. Press the “I” on the switch to turn it on.
The LCD will illuminate. The off position, marked “0”,
turns the machine off.
B. ci r c u i t Br e a k e r
po W e r co r d a n d fo o t sW i t c h
Fig. 5-12. Power Cord and Foot Switch.
a. po W e r co r d
The Power cord is a 220 VAC, NEMA 6-15P and ts a
NEMA 6-15R.
B. fo o t sW i t c h
The Foot Switch allows the operator to start and stop
the laminator while handling the item to be laminated.
The Circuit Breaker will trip if there is too much load.
Wait for 1 minute after the Circuit Breaker trips and
press the switch to reset. If the machine fails to reset,
see “Troubleshooting” on page 7-2.
c. no m e n c l a t u r e pl a t e
Technical information is provided on the
Nomenclature Plate:
Serial Number•
Voltage•
Amps•
Watts•
Hertz•
Press the Foot Switch to run the laminator. Release it
to stop the laminator.
When the Foot Switch is used and the Safety Sensor
is blocked, the speed of the laminator drops to 3 fpm
(0.9 mpm).
When the Feed Table is removed, the rollers will
rotate if the Foot Switch is pressed. The machine will
run at 3 fpm (0.9 mpm)
Page 5-6
Page 19
640t – Installation and Operating Instructions
co n t r o l pa n e l
A
B
D
E
F
I
J
te m p se c t i o n
D. MES (Measure)
Press MES to show the actual Top Main
C
Roller Temperature.
E. Temp Arrow Up
To increase the Top Main Roller temperature,
press and hold.
F. Temp Arrow Down
To decrease the Top Main Roller temperature,
press and hold.
G. HOT
For the factory preset temperature of the Top
G
Main Roller, press HOT.
H. COLD
H
K
For the factory preset temperature of the Top
Main Roller, press COLD
sp e e d se c t i o n
L
M
I. Speed Arrow Up Symbol
To increase the Roller speed, press and hold.
J. Speed Arrow Down Symbol
To Decrease the Roller speed, press and hold.
K. RUN
Press and release RUN for continuous running.
Fig. 5-13. Control Panel.
A. Ready Indicator
The Ready Indicator informs the operator that the
machine has reached the desired set temp of the Top
Main Roller.
B. Temperature Display
The Temperature Display shows the Set Temperature
of the laminator.
L. STOP
Press STOP to stop the machine.
M. REV (Reverse)
Press and hold REV to reverse the direction of the
rollers. Release REV to stop. When in the reverse
mode, the machine will operate at 3 fpm, (0.9mpm)
C. Speed Display
The Speed Display shows the set speed of the
laminator.
Page 5-7
Page 20
640t – Installation and Operating Instructions
Page 5-8
Page 21
640t – Installation and Operating Instructions
6. op e r a t i o n
This chapter describes how to use the laminator to:
Operate the machine•
Load films (web the machine)•
Laminate items•
Mount items•
ge n e r a l op e r a t i o n
These instructions assume that the lms have been
loaded. For information about loading lms, see
“Loading Film” on page 6-2.
To run the laminator:
Turn the laminator 1. On (I) with the power switch
located at the back of the machine.
The Display (“Fig. 6-1. Control Panel.”) is:
Set at • COLD or 32*
Speed • 9
Ready to run•
Set the Roller Pressure Handle for High 2.
Lamination (“Fig. 6-2 Roller Pressure Handle.”).
WARNING: Make sure the print clamp and
feed tray are in their proper positions. Your ngers
and hands could be trapped and crushed in the
rollers. Clothing, jewelry, and long hair could be
caught in the rollers and pull you into them.
Set the Roller Pressure Handle for the thickness 3.
of the item that is to be laminated or mounted.
Set the desired speed on the control panel.4.
Press 5. RUN or the foot switch.
The rollers will begin to turn.
Position the item or items to be laminated or 6.
mounted on the feed table.
Push the item(s) squarely into the roller nip point 7.
(where the two rollers meet).
Fig. 6-1. Control Panel.
Additional items can be laminated or mounted
without stopping and starting the machine.
Release the 8. foot switch or press STOP to
stop the laminator when all of the items have
completely exited the rear of the machine.
Fig. 6-2 Roller Pressure Handle.
Page 6-1
Page 22
640t – Installation and Operating Instructions
Adhesive surface
Adhesive surface
Polyester surface
Polyester surface
Poly-in
Poly-out
lo a d i n g fi l m
The 640t laminator runs poly-in and
poly-out pressure sensitive adhesive (PSA) lms.
Poly-in means the adhesive side of the lm is on the
inside of the lm roll. Poly-out means the adhesive is
on the outside of the lm roll.
IMPORTANT: The top and bottom rolls of laminating
lm must be the same width.
Always change the top and bottom supply rolls at the
same time.
The lm will wrap around the rollers if:
One or both rolls of film are allowed to run •
completely off its core.
Only one roll is used.•
Different widths of rolls are loaded together. •
Either roll is loaded with the adhesive side •
against a roller.
There are two methods of loading lm.
Using a threading card.•
Tacking new film to existing film.•
These are described in “Threading Film with a
Threading Card” on page 6-5 and “Loading Film by
Tacking New Film to Existing Film” on page 6-7. Prior
to loading lm, the print clamp and feed table need
to be removed.
Fig. 6-3. Poly-in and Poly-out Films.
The machine can perform four functions:
Decaling (laminating and applying an adhesive •
to the back of the item).
Mounting, using one film.•
Mounting, using no film.•
Roll-to-roll over-lamination.•
Page 6-2
Page 23
640t – Installation and Operating Instructions
re m o v i n g a n d in s t a l l i n g t h e
r i n t cl a m p
p
The print clamp guides prints into the rollers. It
should be removed when mounting items to thicker
boards. It also needs to be removed to install lms
and when cleaning the rollers.
WARNING: Keep ngers and hands away from
the rollers when the machine is running. They could
be trapped and crushed in the rollers. Clothing,
jewelry, and long hair could be caught in the rollers
and pull you into them.
re m o v i n g a n d in s t a l l i n g t h e
e e d ta B l e
f
The feed table should not be removed except to
install lms. When the table is off, the laminator runs
at a xed speed of 3 fpm (0.9 m).
Fig. 6-5. Table Interlock Latch.
To remove the feed table:
Slide the feed table latch to the right.1.
Fig. 6-4. Print Clamp and Release Latch.
A. Print Clamp
B. Release Latch
To remove the print clamp:
Slide and hold either the left or right latch 1.
towards the center of the laminator.
Lift the end of the print clamp up while 2.
disengaging the opposite end.
To install the print clamp:
Position one end of the print clamp so that its 1.
latch engages into its locking hole.
Lower the other end while retracting the latch so 2.
that the latch lines up with its locking hole.
Lift the table upwards and away from the 2.
laminator.
To install the feed table:
Place the table on the machine.1.
Slide the feed table latch to the left.2.
Release the latch and ensure that both latches 3.
are engaged.
Page 6-3
Page 24
640t – Installation and Operating Instructions
lo a d i n g fi l m on t o t h e su p p l y sh a f t s
If you are loading lm for the rst time, skip these
instructions and start with the instructions,
lms onto the supply shafts:” on page 6-5
replacing existing lms, perform the following set of
instructions,
To remove existing films:
Refer to Figs. 6-6 through 6-8.
Put the roller pressure handle to 1. 1/2”.
A in “Fig. 6-6. Roller Pressure Handle.”
Cut the remaining top and bottom films just 2.
ahead of the pressure rollers. Do not allow the
remaining film to pass through the laminator if
there is any exposed adhesive. Pull the remaining
film out the front of the machine.
“To remove existing lms:” on page 6-4
Fig. 6-6. Roller Pressure Handle.
“To load
. If you are
.
If the unwind/supply shaft (“Fig. 6-7. Unwind/3.
Supply Shafts.”) is on the machine, grasp the
bearing end and lift it out of the cradle (“Fig. 6-8.
Supply Shaft Cradle End.”). Then pull the left end
out of the brake hub.
Fig. 6-8. Supply Shaft Cradle End.
Do the previous steps for the top and bottom 4.
supply shafts.
Slide the core off the shaft and core adaptors. 5.
Tip: Twist the shaft while pulling to remove the
core easier.
Clean the pressure rollers if needed. See 6.
“7. Operator Maintenance” on page 7-1
.
CAUTION: Be careful to not cut the pressure
rollers. Failure to observe this notice can result in
damage to the rollers.
Fig. 6-7. Supply Shafts.
Page 6-4
Page 25
640t – Installation and Operating Instructions
To load films onto the supply shafts:
If the supply shaft is on the machine, grasp the 1.
bearing end and lift it out of the cradle. Then pull
the left end out of the brake hub.
This applies to the top and bottom supply shafts.
Slide the new roll on to the shaft and core 2.
adaptors, referring to “Fig. 6-3. Poly-in and
Poly-out Films.” on page 6-2 to determine how
the film unwinds from the roll. Use the set screws
in the core adaptors to move the adaptors if
needed.
Insert the hex end of the shaft into its brake hub 3.
and then insert the bearing end in its cradle. See
“Fig. 6-7. Supply Shafts.” and “Fig. 6-8. Supply
Shaft Cradle End.”
Center each supply roll on the shafts by doing 4.
the following. Also see “Film Alignment” on page
6-10.
Use a ruler to measure from the left edge of a.
the roll to the left side frame.
Do the same on the right side. b.
th r e a d i n g fi l m W i t h a
h r e a d i n g ca r d
t
The following procedure uses a lm threading card
that is sometimes provided with new rolls of lm. If
one is not provided, a scrap of cardboard or poster
board with a straight edge is suitable. Either can be
reused. Prior to loading lm, remove the print clamp
and feed table.
Note: These instructions are for loading laminating
and mounting lms for decaling. The top supply
shaft is used for laminating lms and the bottom
supply shaft is used for mounting lm or Kraft paper.
If you are not applying mounting lm to a laminate,
Kraft paper should be used on the bottom supply
shaft to prevent adhesive from sticking to the rollers.
For more information about loading lms for other
processes, refer to the appropriate section in this
chapter.
To web (load films) the machine:
Remove the print clamp and feed tray. Refer to 1.
“Removing and Installing the Print Clamp” on
page 6-3 and
Table” on page 6-3.
“Removing and Installing the Feed
Shift the roll side to side so that both c.
measurements are equal. It is important that
the edges of the films are aligned so that
adhesive does not stick to the rollers.
Center the take-up core on its shaft.5.
Pull the top film down, thread it under the idler 2.
bar, and pull the film back up to the take-up core.
Lightly tape both corners of the film to the 3.
take-up core. Ensure that the film is pulled evenly
and that no bulges exist at either end of the idler
bar.
Using a very sharp utility knife, lightly score the 4.
laminating film approximately 4 in (10 cm) above
the upper pressure roller. Be careful to not cut
through the release liner.
Pull the laminating film away from the liner and 5.
drape it over the front of the pressure rollers so
that it extends to a little past the bottom of the
top pressure roller.
Page 6-5
Page 26
640t – Installation and Operating Instructions
Fig. 6-9. Top Film Draped Over the Pressure Rollers and
Release Liner Attached to Take-up.
Pull the mounting film (or Kraft paper) up to 6.
about even with the top of the top pressure roller
without touching the sticky laminating film.
While pulling evenly, carefully align the edges of 7.
the mounting film with the laminating film, and
press the two together. It is important that the
tension is even from one end of the supply rolls
to the other.
Fig. 6-10. Bottom Film or Kraft Paper Stuck to Top Film.
Press the straight edge of the threading card into 8.
the two films at the nip (the point between the
two pressure rollers) until the card and films are
slightly past the nip.
Fig. 6-11. Threading Card Inserted Between Films.
Move the roller pressure handle to where it 9.
applies pressure to the threading card.
Press 10. RUN on the control panel or while pressing
the foot switch, guide the threading card into
the machine until the rollers pull the card on their
own.
WARNING: Keep your ngers and hands away
from the nip point while the machine is running, they
could be trapped and crushed in the rollers. Clothing,
jewelry, and long hair could be caught in the rollers
and pull you in.
Release the card and ensure that both films and 11.
card are being pulled into the laminator.
The card will guide the film webs into the rollers.
Press 12. STOP or release the foot switch.
Replace the feed table and print clamp. 13.
Refer to “Removing and Installing the Print
Clamp” on page 6-3 and
the Feed Table” on page 6-3
Check the film alignment and adjust the tension if 14.
needed. See “Film Alignment” on page 6-10.
“Removing and Installing
.
Page 6-6
Page 27
640t – Installation and Operating Instructions
lo a d i n g fi l m B y ta c k i n g ne W fi l m t o
x i s t i n g fi l m
e
The following describes a method for loading lm
whereby the existing lm on the rollers may be used
in place of the threading card to draw the new lm
through the laminator. Leading edges of the new
lm will be overlapped onto the adhesive of the old
lm. The existing lm and the new lm will be pulled
through the laminator together.
Remove the print clamp and feed tray. Refer to 1.
“Removing and Installing the Print Clamp” on
page 6-3 and
Table” on page 6-3
Cut the remaining bottom film web between the 2.
supply roll and rollers.
Remove the existing bottom supply roll and 3.
replace with new film. Refer to “Loading Film
Onto the Supply Shafts” on page 6-4.
Unroll enough film from the bottom roll of film 4.
to tack to the existing bottom film. Make sure
to carefully align the edges of the films before
tacking them together.
“Removing and Installing the Feed
.
Set the speed for the slowest speed setting, 9.
press RUN or the foot switch.
Watch the film being pulled through the laminator 10.
to ensure that the remaining existing film and the
new film are advancing concurrently and evenly.
Any separation between the films will require
stopping the motor immediately and the situation
corrected.
Release the 11. foot switch or press STOP once
the newly threaded film completely exits the
laminator.
Check the film alignment and adjust the tension 12.
if needed.
See “Film Alignment” on page 6-10.
Cut the remaining top film web between the 5.
supply roll and rollers. Do not allow the adhesive
to stick to the rollers or the bottom film.
Remove the existing top supply roll and replace 6.
with new film.
Unroll enough film from the top supply roll shaft 7.
to tack to the existing top film. Make sure to
carefully align the edges of the films before
tacking them together.
Fig. 6-12. New Films Tacked to Old Films.
Install the feed table and print clamp.8.
Page 6-7
Page 28
640t – Installation and Operating Instructions
de c a l i n g in tW o pa s s e s
Decaling is where you laminate items and then
mount them on other materials such as Foam Core
or mounting board. It is performed in two passes.
The rst pass laminates and applies the mounting
adhesive, encapsulating the item. The second pass
mounts it on rigid material.
This two pass operation requires pressure sensitive
laminating lm on the top supply shaft and pressure
sensitive mounting lm on the bottom supply shaft.
Refer to “Fig. 6-14. Congurations for Poly-in and
Poly-out Films.” for the proper conguration of
Poly-in or Poly-out lm.
Tak e-up
PSA Film
Release liner
Guide the item into the rollers.4.
Once the item has cleared the back of the 5.
machine, release the foot switch or press STOP.
Remove the web and trim out the encapsulated 6.
item.
To run the second pass:
Unweb (unload the lms) the laminator before running
the second pass.
Print over roller and idler bar
Release liner
PSA mounting lm
Fig. 6-13. Laminator Loaded for Decaling the First Pass
Poly-in
Fig. 6-14. Congurations for Poly-in and Poly-out Films.
with Film (Poly-in Shown).
Poly-out
To run the first pass:
Load the laminator as shown in “Fig. 6-13. 1.
Laminator Loaded for Decaling the First Pass
with Film (Poly-in Shown).”.
Adjust the roller pressure handle to the proper 2.
laminating setting.
Fig. 6-15. Laminator Ready for Mounting.
Adjust the roller pressure handle to the proper 1.
mounting setting.
Set the motor speed to 2. min.
Peel back the leading edge of the release liner 3.
of the laminated item approximately 4 inches (10
cm).
Place the item on the mount board. 4.
Tack the exposed adhesive edge of the item, 5.
from the center out, to the leading edge of the
board.
Be sure to not introduce wrinkles or air bubbles.
Butt the leading edge of the board up against the 6.
rollers.
Drape the encapsulated item over the idler bar. 7.
Do not allow the print to flop backwards.
Press 8. RUN or the foot switch.
Place the item to be laminated on the feed table 3.
and press RUN or the foot switch.
Page 6-8
Immediately grasp the release liner for separation 9.
as the board is pulled into the rollers. Do not
allow the release liner to be pulled into the rollers.
Page 29
640t – Installation and Operating Instructions
After the board has cleared the rollers, release 10.
the foot switch or press STOP.
mo u n t i n g
ti p s fo r th r e a d i n g pr e s s u r e
e n s i t i v e ad h e s i v e (psa) fi l m
s
Use Kraft paper for one-sided lamination.•
Refer to “Fig. 6-14. Configurations for Poly-in •
and Poly-out Films.” for the proper film
configuration.
Whenever possible, pull the remaining web •
of film out the front of the laminator after the
finished item has been removed.
pr e -co a t i n g Bo a r d s
You may wish to pre-coat mounting boards ahead of
time with PSA mounting lm.
Press 6. STOP when the last board exits the
machine.
mo u n t i n g on l y
This process requires a decaled item with PSA
mounting adhesive. Refer to the
pass instructions
of this chapter. An alternative method is to use a PSA
pre-treated board on page 6-8, gure 6.15
in the
Decaling In Two Passes
To run the second
section
ro l l -t o -ro l l
Load and thread the lm and media as described in
“Loading Film Onto the Supply Shafts”
Film with a Threading Card”
step 14, attach the web to the rear rewind tube with
masking tape.
. After you have nished
and
“Threading
PSA mounting lm
Board
Fig. 6-16. Laminator Ready for Pre-Coating Boards.
To pre-coat boards:
Load the laminator as shown in “Fig. 6-16. 1.
Laminator Ready for Pre-Coating Boards.”
Adjust the roller pressure handle to the proper 2.
mounting setting.
Start a leader board into the rollers. 3.
Press 4. RUN or the foot switch.
Release liner
PSA overlam
Rear rewind
Adhesive back media
Fig. 6-17. Laminator Ready for Roll-to-Roll.
Continue feeding one board after another. 5.
Tip: Butt the leading edge of the next board to
the trailing edge of the previous one to ensure an
even application of film.
Page 6-9
Page 30
640t – Installation and Operating Instructions
fi l m al i g n m e n t a n d te n s i o n
fi l m al i g n m e n t
The top and bottom supply rolls must be aligned
as closely as possible. Misalignment can cause
adhesives to stick to the rollers.
Measure here
Fig. 6-18. Measuring Points on a Typical Laminator..
To align the supply rolls:
fi l m te n s i o n
Proper lm tension, known as brake tension, is the
minimum amount required to eliminate wrinkles in
the nished item. As the lm roll becomes smaller,
tension increases, thus the adjustment needs
to be loosened. Film tension should be checked
occasionally to ensure that the adjustment is correct.
The lm should be taut with no gaps between the
lm and pressure rollers. A properly adjusted roll of
lm should not require excessive force to turn by
hand. Film tension should be enough to introduce a
minor amount of drag as the lm unrolls. Insufcient
tension causes wrinkles, while too much tension
causes stretching (necking). Uneven tension between
the top and bottom rolls create curl. Too much upper
tension creates upward curl. Too much lower tension
bottom causes downward curl.
Use a ruler to measure the distance between the 1.
left edge of the roll to the side frame.
Measure the distance between the right side of 2.
the roll to the side frame.
Shift the roll side to side to ensure that the two 3.
measurements are equal.
Fig. 6-19. Tension Adjustment Knobs and Motor.
The machine is equipped with external tension knobs
located on the left side. Turning the knobs clockwise
increases the tension while counterclockwise
decreases the tension.
Refer to “Tension Controls” on page 5-4.
Page 6-10
Page 31
640t – Installation and Operating Instructions
Testing the Web
After webbing the machine, it is important that the
lms run straight and evenly.
To test the web:
Set the roller pressure handle to an appropriate 1.
position.
Press 2. RUN or the foot switch and run
approximately 6 in. (10 cm) of laminate.
Press 3. STOP or release the foot switch.
Visually inspect the top and bottom films where 4.
they enter the nip.
The films should be tight against the rollers
at both ends. If they are not, use the tension
adjustment knobs to tighten the loose supply film
brake and run another test.
Ensure that the release liner take-up is keeping 5.
the liner tight against the idler bar.
Use the upper film supply tension knob to
properly tension the release liner.
Run test materials before laminating good 6.
materials.
cl e a r i n g a fi l m Ja m (Wr a p -u p )
Film jams (wrap-ups) may occur if the lm is loaded
backwards or if the area at which lm exits the
equipment is blocked. The lm, when jammed, wraps
around the rollers. Jams also occur if something is
too large to pass through the rollers.
Determine the best course of action to clear the
jam. It may be necessary to rotate the rollers in the
reverse direction. Set the speed to min. Press and
hold REVERSE on the control panel.
CAUTION: Be careful to not cut the pressure rollers
when cutting the lm. Failure to observe this notice
can result in damage to the rollers.
To clear a jam:
Immediately press 1. STOP to stop the machine.
Remove the print clamp and feed tray.2.
Do one of the following.3.
Pull one of the webs while running the a.
laminator in reverse.
Cut the film near the rollers, set the b.
pressure adjustment to 1/2”, and pull the
film out the back of the machine.
Cut the film near the rollers, set the c.
pressure adjustment to 1/2”, grasp the
loose ends of the web, and pull straight out
the front of the machine.
Replace the feed tray and print clamp. See 4.
“Removing and Installing the Feed Table” on
page 6-3 and “Removing and Installing the Print
Clamp” on page 6-3.
Re-load the film if necessary. See5.
on page 6-2
.
“Loading Film”
Page 6-11
Page 32
la m i n a t i o n gu i d e
This manual provides general guidelines and is only
a general reference guide. Different settings may be
suitable as the lamination time and materials change.
Test materials before running good materials through
the machine.
Do not attempt to laminate abrasive or metal •
objects such as staples, paper clips and glitter,
as they may damage the rollers.
Do not force items into the nip area of the rollers. •
An item that is not easily drawn into the laminator
by the rollers is probably too thick to laminate.
Wrinkles may result if an attempt is made to •
reposition an item once it has been grasped by
the rollers.
640t – Installation and Operating Instructions
Do not stop the laminator before an item has •
completely exited the pressure rollers. Even
a momentary stop may cause a mark on the
laminated item.
Good, consistent lamination is a result of •
combining proper tension and roller pressure.
Do not combine thick and thin items at the same •
time, as this will result in a poor edge seal around
the thinner material.
Page 6-12
Page 33
640t – Installation and Operating Instructions
7. op e r a t o r ma i n t e n a n c e
ca r i n g f o r t h e 640t la m i n a t o r
The only maintenance required by the operator
is to periodically clean the rollers. The following
procedure will help keep the rollers free of dirt and
adhesive, which has been deposited along the edge
of the laminating lm. Proper alignment of the rolls of
lm reduces the amount of adhesive on the rollers.
Perform only the routine maintenance procedures
referred to in these instructions.
WARNINGS:
Do not attempt to service or repair the laminator. •
Do not apply any cleaning uids or solvents to the •
rollers. Some solvents and uids could damage
the rollers.
Keep ngers and hands away from the rollers •
when the machine is running. They could be
trapped and crushed in the rollers. Clothing,
jewelry, and long hair could be caught in the
rollers and pull you in.
Failure to observe these warnings could result in
severe personal injury or death or damage the
machine.
To clean the rollers and idler bar:
Remove the print clamp and feed table. Refer 1.
to “Removing and Installing the Print Clamp” on
page 6-3 and “Removing and Installing the Feed
Table” on page 6-3.
Remove the film from the laminator. Refer to2.
“Loading Film Onto the Supply Shafts” on page 6-4
Use the dampened cloth to remove any dust, 3.
dirt, and other foreign materials from the rollers.
Press and release the 4. foot switch to rotate the
rollers to an unclean portion.
Keep your hands, fingers, pad, and rag away
while running the machine. Be sure to remove all
adhesive and dirt.
Install the feed table and print clamp.5.
cl e a n i n g th e ro l l e r s
Keeping the rollers clean ensures that your nished
items will not be damaged by dirt and adhesives.
Clean the rollers with a clean, damp lint-free cloth.
If there are any adhesive build ups, you may use
isopropyl alcohol instead of water.
Never clean rollers with abrasive, sharp, or •
pointed objects.
Do not use any other cleaning agents other •
than those listed above.
Accumulated adhesive deposits on the rollers •
can cause damage to the rollers. Rotate the
rollers at the lowest speed setting on the
control panel.
Page 7-1
Page 34
640t – Installation and Operating Instructions
tr o u B l e s h o o t i n g
Symptom Possible Cause Corrective Action
LCD does not illuminate on
the control panel when the
ON/OFF switch is in the
ON position.
Rollers do not turn. Infrared eyes blocked. Unblock infrared eyes.
Laminated items are
curling.
Adhesive deposited on
rollers.
Unsatisfactory laminate
adhesion.
Laminator not connected to electrical
supply.
Circuit Breaker tripped. Reset Circuit Breaker.
Feed tray interlock latch not in place. Slide interlock latch all the way to the left
Tension between the top and bottom film
roll is unequal.
Speed setting too slow. Slightly speed up laminator.
Top and bottom film webs not aligned. Align film webs per
Laminate improperly loaded. Load film per
Insufficient roller pressure. Adjust the roller pressure.
Laminate improperly loaded. Load film per procedure outlined per
Insert attachment plug into receptacle.
into the side frame.
Adjust tension per
6-10
.
page 6-10
“Loading Film” on page 6-2.
.
“Film Tension” on page
“Film Alignment” on
“Loading Film” on page 6-2.
Page 7-2
Rollers require cleaning. Clean rollers per
page 7-1.
Laminated item unsuitable for adhesion. Item may be dirty or may have non-
porous surface that is extremely difficult
to laminate.
Cleaning the Rollers
Page 35
640t – Installation and Operating Instructions
no t e s
Page 7-3
Page 36
ACCO Br ands
300 Tower Pa rkwa y
Linco lnshire, IL 60069-3640
In USA call 800.541.0094
www.accobrands.com
www.gbc.com
ACCO Ca nada - Br ampton
5 Precidio Court
Brampton, ON L6S-6B7 CANA DA
Au Ca nada, c omposez l e 800.463.2545
www.acco.ca
ACCO ME XICANA S.A. D E C.V.
Circuito de al In dustria Nor te No. 6
Parque Industrial Lerma,
Lerma Edo. de México
C.P. 52000 M éxico
En México llame al 52.55.15005700
Desde el extranjero: 52.72.22656501
www. accomexico.com
www.gbc.com.mx
© 2009 ACC O Brand s. All rights reserve d. ACCO® i s a registered tradema rk of
ACCO Br ands. GB C® is a registere d trade marks of Gener al Binding Corporation.
© 2009 ACC O Brand s. Tous droit s réser vés. ACCO® es t une marque de com merce
dépos ée d’ACCO Br ands. GBC® est une marque de comme rce déposée de General
Binding Corporation.
© 2009 ACC O Brand s. Todos los derecho s reser vados. ACCO® e s una marca registrad a
de ACCO Brands. G BC® es un a marca regist rada de General Binding Corporation.
04048E001 0110
Loading...