GarrettCom 6K16V User Manual
Magnum 6K16V
Managed Fiber Switch
Hardware
www GarrettCom com
..
i
Installation and User Guide
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
Magnum
6K16V
Managed Fiber Switch
Hardware
Installation and User Guide
Part #: 84-00125 (Rev. A)
Trademarks
Ethernet is a trademark of Xerox Corporation
NEBS is a trademark of Telcordia Technologies
UL is a registered trademark of Underwriters Laboratories
GarrettCom, Magnum and Personal Switch are trademarks and Personal Hub is a
registered trademark of GarrettCom, Inc.
Important: The Magnum 6K16V Managed Fiber Switch contains no user
serviceable parts. Attempted service by unauthorized personnel shall render all
warranties null and void. If problems are experienced with Magnum 6K16V
Switch products, consult Section 6, Troubleshooting, of this User Guide.
Copyright 2004 GarrettCom, Inc. All rights reserved. No part
of this publication may be reproduced without prior written permission from
GarrettCom, Inc.
Printed in the United States of America.
www GarrettCom com
..
i
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
Contacting GarrettCom, Inc
Please use the mailing address, phone and fax numbers and email address listed below:
GarrettCom, Inc.
213 Hammond Ave.
Fremont, CA 94539
Phone (510) 438-9071
Fax (510) 438-9072
Website: http://www.GarrettCom.com
email support@garrettcom.com
Federal Communications Commission
Radio Frequency Interference Statement
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference in a residential installation. This equipment generates, uses, and can
radiate frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interfernce to radio communications. However, there
is no guarantee that interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into n outlet on a ccircuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio TV technician for help.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil respecte toutes les exigences du Réglement sur le matériel du
Canada. Cet appareil est Classe B.
www GarrettCom com
..
Canadian Emission
ii
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
Table of Contents................................................................................. Page
1.0
SPECIFICATIONS ............................................................................... 1
1.1 Technical Specifications ...................................................................... 1
1.2 Ordering Information........................................................................... 4
2.0 Introduction............................................................................................ 6
2.1 Inspecting the Package and Product .................................................... 6
2.2 Product Description - Magnum 6K16V Managed Fiber Switch.......... 7
2.2.1 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC), .................. 8
2.2.2 Eight-Port Copper Module, 6K8-RJ45 ........................................ 9
2.2.3 Six-Port “4 + 2” Combo Modules,............................................... 9
2.2.4 Four-Port 10 Mb and 100Mb mm Fiber ST Modules............. 11
2.2.6 Gigabit (1000Mbps) port modules............................................. 11
2.2.6 Packet Prioritization, 802.1p QOS............................................. 12
2.2.7 Frame Buffering and Flow Control............................................ 12
2.2.8 Managed Network Software ( MNS-6K ) for Magnum 6K16V 13
2.3 Features and Benefits......................................................................... 14
2.4 Applications ....................................................................................... 15
3.0 Installation...........................................................................................18
3.1 Locating Magnum 6K16V Switches.................................................. 18
3.2 Connecting Ethernet Media ............................................................... 18
3.2.1 Connecting Fiber Optic ST-type, “twist-lock”.......................... 19
3.2.2 Connecting Fiber Optic SC-type, "Snap-In".............................. 19
3.2.3 Connecting Single-Mode Fiber Optic ........................................ 19
3.2.4 Connecting Twisted Pair (RJ-45,CAT3, CAT5,)....................... 20
3.2.5 Connecting Twisted Pair (CAT5E or better,) ............................ 20
3.2.6 Connecting Gigabit Media Using GBICs .................................. 21
3.3 DIN-Rail Mounting............................................................................ 21
3.3.1 Mounting Dimensions for 6K16V with metal brackets ............. 22
3.4 Powering the Magnum 6K16V Managed Fiber Switch..................... 23
3.5 Alarm Contacts for monitoring internal power, and Software Traps.... 24
3.6 6K16V Port Module (6KPM) Installation ......................................... 25
3.6.1 Preparation for Installing and Removing 6KPMs............................ 25
3.6.2 Installing 6KPM Cards in the Magnum 6K16V ........................ 27
3.6.3 Removing 6KPM Cards............................................................. 30
3.7 Connecting a Management Console Terminal to Magnum 6K16V... 31
3.7.1 RS-232 (DB-9) Console Com port (Serial port) pin. ................. 31
4.0 OPERATION....................................................................................... 32
4.1 Switching Functionality ..................................................................... 32
4.2 Status LEDs ....................................................................................... 33
4.3 Up-link Manual Switches set as (=) , for RJ-45 port only ................. 33
4.4 Auto-negotiation, for Fast Ethernet copper ports............................... 33
4.5 Flow-control, IEEE 802.3x standard ................................................. 35
4.6 Power Budget Calculations for Magnum 6K16V PM’s .................... 35
www GarrettCom com
..
iii
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
5.0
Introduction - Magnum 6K16V Managed Fiber Switch PM........... 37
5.1 Inspecting the Package and Product .................................................. 37
5.2 6KPM Module Description................................................................ 37
5.2.1 6KP6-RJMST, Combo Module.................................................. 38
5.2.1a 6KP6-RJ10ST, Combo Module................................................. 38
5.2.1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST “twist lock” ....... 38
5.2.1c 6KP4-FLSTFX, 2 Module ......................................................... 39
5.2.2. 6KP6-RJMSC ............................................................................ 40
5.2.3 6KP6-RJSSC “snap-in” connector............................................ 40
5.2.4
6KP6-RJSSCL “snap-in” connector .......................................... 41
5.2.4a
6KP6-RJ10ST “twist-lock” connector ....................................... 41
5.2.5 6KP8-MTRJ,.............................................................................. 42
5.2.5a 6KP6-MT10ST, ST-Fiber port................................................... 42
5.2.6 6KP8-45MT, .............................................................................. 43
5.2.7 6KP8-MLC, ............................................................................... 43
5.2.8
6KP8-45LC, Combo Connector ............................................... 44
5.2.9 6KP8-RJ45 (Twisted Pair), 10/100Mb 8-Port .......................... 44
5.2.10 6KP8-45-2MT, MTRJ Small-Form-Factor................................ 45
5.2.10a
6KP8-45-2LC, LC Small-Form-Factor ..................................... 46
5.2.11 GBIC-SXSC Gigabit fiber(1000Mb), mm SC Connector ......... 46
5.2.11a
GBIC-LXSC Gigabit fiber (1000Mb), mm SC Connector......... 47
5.2.12 6KM-BLNK............................................................................... 47
6.0 TROUBLESHOOTING...................................................................... 48
6.1 Before Calling for Assistance ............................................................ 48
6.2 When Calling for Assistance ............................................................. 49
6.3 Return Material Authorization (RMA) Procedure ............................. 49
6.4 Shipping and Packaging Information................................................. 50
APPENDIX A: WARRANTY INFORMATION.........................................50
APPENDIX B : Internal DC Power Supply Options.................................... 51
APPENDIX C: Internal DC Dual-Source Power Option............................. 54
Revisions
06/04 : New port modules has been added and updated on Alarm contacts
01/04 : Added Section 3.5 (Alarm Contacts) and 3.7.1 (Console Port pins)
12/03: Updated Section 3.3 “DIN-Rail”, and Appendix B “DC Power”
10/03 : Initial Release with Rev A
www GarrettCom com
..
iv
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
THE MAGNUM LINE
Ethernet connectivity products
"Designed and Manufactured in the USA"
Overview
GARRETTCOM, INC. OFFERS THE PREMIUM-QUALITY MAGNUM
LINE OF ETHERNET LAN CONNECTIVITY PRODUCTS WITH
INDUSTRY-STANDARD FUNCTIONALITY AND BUILT-IN FIBER
CONFIGURABILITY. MAGNUM PRODUCTS ARE DESIGNED FOR USE
IN DEMANDING CARRIER CLASS, INDUSTRIAL GRADE AND OEM
APPLICATIONS WHERE RELIABILITY IS A PRIMARY
CONSIDERATION.
6K-SERIES MANAGED FIBER SWITCHES, GIGABIT, 100 AND 10
MBPS, FIBER AND COPPER PORTS, MIX-AND MATCH. FEATURES
SFF FIBER AND DC POWER IN 1U UNITS.
4K-SERIES SWITCHES, 100 AND 10 MBPS, COPPER PORTS WITH
OPTIONAL FIBER PORT, WITH AUTO-NEGOTIATING FULL
SWITCHING PERFORMANCE.
QUAD-SERIES FIBER SWITCHES, 100 & 10MBPS, FIBER AND
COPPER PORTS, MIXED-SPEED AND MIXED-MEDIA TYPES, FULL
SWITCHING PERFORMANCE.
“OUTDOOR” ETHERNET SWITCH, FOR TEMPERATURE
UNCONTROLLED LOCATIONS
6 10/100 AND 2 100MB FIBER PORTS, CAN BE CONNECTED IN
STRINGS
MIXED-MEDIA FIBER HUB, 16-PORT STACKABLE,10/100 AUTO-
SENSING
DUAL SPEED 8-PORT AND 16-PORT STACKABLES, 10/100 AUTO-
SENSING
STACKABLE HUBS, SNMP OPTIONAL
10MB SERIES AND 100MB SERIES, BOTH W/ OPTIONAL PORT
MODULES
PERSONAL SWITCHES, 10/100MB
8 PORT DUAL SPEED, AUTO-NEGOTIABLE WITH FIBER OPTION
PERSONAL HUBS, 100MB OR 10/100MB
8-PORT, WITH TWO SWITCHED PORTS (1 FIBER BUILT IN)
PERSONAL HUBS, 10MB SERIES
8-PORT + AUI, STACKABLE TO 5 HIGH, + OPTIONAL BNC OF FIBER
PORT
www GarrettCom com
..
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
8 OR 9-PORT AND 4 OR 5-PORT PERSONAL HUBS, W/ MAN. UP-LINK
SW.
MEDIA CONVERTERS, 10MB AND 100MB SERIES
ALL MEDIA COMBINATIONS, INCL. FIBER ST, SC, MM., SINGLE
MODE
THE “X-LINE” OF CONFIGURABLE MIXED MEDIA PRODUCTS:
STACKABLE CONCENTRATORS, SNMP OPTIONAL, 13-PORTS
MINI-CONCENTRATORS, 7 PORTS, REPEATERS, 2-PORTS
REPEATER PORT MODULES (RPMS), 6 TYPES FOR ETHERNET
MEDIA
BRIDGE PORT MODULES (BPMS), 4 TYPES, FOR SEGMENT
ISOLATION
TRANSCEIVERS, 10MB SERIES MINI-TRANSCEIVERS AND COAX
MODELS JUNE, 04
www GarrettCom com
..
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
1.0 SPECIFICATIONS
1.1 Technical Specifications
Performance
Filtering / Forwarding Rate:
Ethernet:14,880 pps
Fast Ethernet: 148,800 pps
Gigabit Ethernet: 1, 488,000 pps
Switching Processing Type: Store and Forward with IEEE 802.3x full-
duplex flow -control, non-blocking
Data Rate: 10Mbps,100Mbps and 1000Mbps
Address Table Capacity: 4K node, self-learning with address aging
Packet buffer size : 240KB for 10/100 and 120KB for 1000Mb
Latency: 5 s + packet time (100 to 100Mbps)
15 s + packet time (10 to 10 Mbps, and 10 to 100Mbps)
Network Standards and Compliance, hardware
Ethernet V1.0/V2.0 IEEE 802.3: 10BASE-T,
IEEE 802.3u: 100Base-TX, 100BASE-FX
IEEE 802.3z: 1000BASE-TX Ethernet (Auto-Negotiation)
IEEE 802.3ab: 1000BASE-TX Ethernet
IEEE 802.1p: Priority protocol
IEEE 802.1d: Spanning tree protocol
IEEE 802.1q: VLAN Tagging
IEEE 802.3x: Flow Control
Maximum 10 Mbps Ethernet Segment Lengths
Unshielded twisted pair - 100 m (328 ft)
Shielded twisted pair - 150 m (492 ft)
10BASE-FL multi-mode fiber optic - 2 km (6,562 ft)
10BASE-FL single-mode fiber optic - 10 km (32,810 ft)
Maximum Standard Fast Ethernet Segment Lengths:
10BASE-T (CAT 3, 4, 5 UTP) - 100 m (328 ft)
100BASE-TX (CAT 5 UTP) - 100 m (328 ft)
Shielded twisted pair - 150 m (492 ft)
100BASE-FX, half-duplex, multi-mode - 412 m (1350 ft)
100BASE-FX, full-duplex, multi-mode - 2.0 km (6,562 ft)
100BASE-FX, half-duplex, single-mode - 412 m (1350 ft)
100BASE-FX, full-duplex, single-mode - 20.0 km (66K16V ft)
100BASE-FX, full-duplex, Long Reach - 40.0 km (122K ft)
Maximum Standard Gigabit Ethernet Segment Lengths:
1000BASE-T (CAT5e or higher is recommended) - 100 m (328 ft)
1000BASE-SX, full-duplex, multi-mode(62.5m cable) - 220m
1000BASE-SX, full-duplex, multi-mode(50m cable) - 550m
1000BASE-LX, full-duplex, single-mode(62.5m cable) -5Km
Fiber Multi-mode connector types supported:
Fiber Port, ST-type (twist-lock):Fiber multi-mode, 10Mb 10BASE-FL
Fiber Port, MTRJ-type (plug-in):SFF Fiber multi-mode100BASE-FX
Fiber Port, SC-type (snap-in):Fiber optic multi-mode, 100BASE-FX
Fiber Port, ST-type (twist-lock): Fiber optic m.-mode, 100BASE-FX
Fiber Port, 1000BASE-FX, GBIC modules
www GarrettCom com
..
1
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
Fiber Single-mode connector types:
Fiber Port, SC-type: Fiber optic single-mode, 100BASE-FX
Fiber Port, LC-type Fiber SFF single-mode, 100BASE-FX
Fiber Port, 1000BASE-FX, GBIC modules
LEDs: Per Port (one set at the port, one set in top or front)
LK: Steady ON when media link is operational
ACT: ON with receiver port activity
FDX/HDX: ON = Full-Duplex Mode
OFF = Half-Duplex Mode
100/10: ON = 100Mbps speed
OFF = 10 Mbps
Operating Environment
Ambient Temperature:
-40 to 140 F (-40 to 60C) for UL60950 and Component Parts rating
-60 to 205 F (-50 to 95C) for IEC 60068 Type Test short term rating
Storage Temperature: -60to 210F (-50to 100C)
Ambient Relative Humidity: 5% to 95% (non-condensing)
Altitude: -200 to 13,000 ft. (-60 to 4000m)
Conformal Coating (humidity protection) option: Request quote
Alarm Relay Contacts
One NC indicating internal power, one NC software controllable
Packaging
Enclosure: Rugged High strength sheet metal. Suitable for vertical wall or
DIN-Rail mounting
Dimensions: 9.5 in. H x 8.75 in. W x 1.75 in. D
24.1 cm H x 22.2 cm W x 4.4 cm D
Cooling method: Convection, designed for vertical mounting, no fans
Weight: 4.21 lbs. (1.9 kg)
Management Console connector
DB-9 for RS-232 “ null-modem “ cable (sometimes called an X-modem cable)
Power Supply (Internal)
AC Power Connector: IEC-type, male recessed at rear of chassis,
Input Voltage: 100 to 240 VAC (auto-ranging)
Input Frequency: 47 to 63 Hz (auto-ranging)
Power Consumption:
50 watts typical (for a fully loaded fiber model)
30 watts typical (for a fully-loaded copper only model)
DC Power Supply (Options)
-48VDC Power Input Voltage : -36 to -70 VDC
24VDC Power Input Voltage : 20 to 36VDC
125VDC Power Input Voltage : 115 to 150VDC
5VDC Power Input Voltage : (+) or (-) 5%
Std. Terminal Block : “ -, GND, + ”
Power Consumption: same as for AC models, see above
www GarrettCom com
..
2
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
For DC internal power supplies at –48VDC, 24VDC and 125VDC,
including Dual Source options (
DC input sources are interrupted)
Per-port jumpers and switches
The copper daughter board has on internal switch for selecting MDI-MDIX
crossover on port # 1. Factory default setting is MDI, user port.
Other port-specific user settings ( such as FDX or HDX, copper 10/100 speed)
can be fixed using software commands.
Agency Approvals
UL listed (UL60950), cUL, CE, Emissions meet FCC Part 15, Class A
NEBS L3 and ETSI compliant
IEEE P1613 Environmental Standard for Electric Power Substations
IEC61850 EMC and Operating Conditions Class C for Power Substations
NEMA TS-2 and TEES for traffic control equipment.
Warranty: Three years, per UL 60950 temperature rating Made in USA
NEBS Test Classification: NEBS Compliant
Email
sales@GarrettCom.com
for continuity of operation when either of the
, see Appendices B and C.
for details.
www GarrettCom com
..
3
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
1.2 Ordering Information
Magnum Managed Fiber Switch (16 ports max)
MODEL DESCRIPTION
Magnum 6K16V-Magnum 6K16V Managed Fiber Switch, base unit for vertical
mounting
May be configured with a selection of 10/100/1000 6K16V fiber and copper
port connector types, 16 total ports max. Two metal brackets for vertical wall or panel
mounting. Wire speed filtering and forwarding across all ports, 802.3x flow control,
802.1p priority packet processing, self-learning 4K-node address table, large 240KB
packet buffers for 10/100 and 120KB for 1000Mb. For licensed managed networks
software (MNS-6K and S-ring), See separate data sheets.
Magnum 6K16V-24VDC: Same as 6K16V except the power input is 24VDC
Magnum 6K16V-5VDC: Same as 6K16V except the power input is 5VDC reg & fused
Magnum 6K16V-48VDC: Same as 6K16V except the power input is –48VDC
Magnum 6K16V-125VDC: Same as 6K16V except the power input is 125VDC
Configuration Options:
Each Magnum 6K16V base unit has TWO port module slots
Magnum 6K16V Port Modules
6KP8V-MTRJ SFF Fiber module, w/eight 100Mb mm FX MT-RJ connectors
6KP8V-MLC SFF Fiber module, w/eight 100Mbps mm FX LC connectors
6KP8V-SLC SFF Fiber module, w/eight 100Mbps sgl-m FX LC connectors
6KP4V-FXSC “2+2” 100Mb Fiber module, w/ four 100Mb 2km FX SC connectors
6KP4V-FXST “2+2” 100Mb Fiber module, w/ four 100Mb 2km FX ST connectors
6KP4V-F10ST “2+2” 10Mb Fiber module, w/ four 10Mb 2km FL ST connectors
6KP4V-FLSTFX “2+2” ST Fiber module, w/ two 100Mb & two 10Mb ports, 2km
6KP8V-RJ45 TP Module, w/eight 10/100Mbps auto-negotiating RJ-45 ports
6KP8V-45MT “4+4” module, w/four RJ-45 ports and four 2km mm FX MT-RJ’s
6KP8V-45MLC “4+4” module, w/four RJ-45 ports and four 2km mm LC connectors
6KP8V-45SLC “4+4” module, w/four RJ-45 ports and four 2km sgl-m LC connectors
6KP6V-RJMST “4+2” module, w/four RJ-45 ports and two 2km mm FX SC’s
6KP6V-RJMSC “4+2” module, w/four RJ-45 ports and two 2km mm FX ST‘s
6KP6V-RJSSC “4+2” module, w/four RJ-45 ports and two 20km Sgl.m FX SC’s
6KP6V-RJSSCL “4+2” module, w/four RJ-45 ports and two 40km Sgl.m FX SC’s
6KP6V-MT10ST “4+2” module, w/four MTRJ ports and two 10Mb 2km FL ST’s
6KP6V-RJ10ST “4+2” module, w/four RJ-45 ports and two 10Mb 2km FL ST ‘s
6KM-BLNK Blank cover for one 6K16V (A,B) module slot opening in a 6K16V
Gigabit (1000Mb) module option
6KP5V-G4RJ “G+2” module, w/one GBIC transceiver and four 10/100 RJ-45
connectors
6KP3V-G2SC “G+2” module, w/one GBIC transceiver and two 100Mb 2km FX SC
www GarrettCom com
..
4
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
fiber ports connector
GBPM-2OTX Two-port Gigabit 6K module for 6K16V Switches, provides two GBIC
open transceiver port for a user-selectable GBIC transceiver module
GBPM-COTX One slot Gigabit 6K module for 6K16V Switches, uses one 6K16V slot
and provides one GBIC open transceiver port for a user-selectable GBIC transceiver
module
GBIC-SXSC GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-SX
port with mm SC fiber connector
GBIC-LXSC10 GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-
LX/LH port with 1310nm sgl. mode SC(10km) fiber connector
GBIC-LXSC25 GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-
LX/LH port with 1310nm sgl. mode SC(25km) fiber connector
GBIC-LXSC40 GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-ZX
port with 1550nm, sgl. mode SC(40km) fiber connector
GBIC transceiver module for use in GBPM-COTX, one LX port with mm SC fiber
connector
GBIC-LXSC70 GBIC transceiver module for use in GBPM-xOTX, one 1000BASE-ZX
port with 1550nm, sgl. mode SC(70km) fiber connector
GBIC-TP GBIC transceiver module for use in GBPM-xOTX, one 802.3ab
1000BASE-T port, RJ-45 connector
CONSOLE CBL Industry standard serial cable, DB-9 connectors for RS-232 “ null-
modem “ connection (sometimes called an X-modem cable), used to connect a PC or a
character terminal to the Management port.
CONSOLE USB Industry standard serial cable, DB-9 connectors for RS-232 “ null-
modem “ connection (sometimes called an X-modem cable) to connect to a managed
switch, and a USB port to connect to a PC
DIN-RAIL-VRM Set of two DIN-Rail holders for a secure vertical mount of a 6K16V
unit, with screws to attach to metal mounting brackets and to the 6K16V case.
GarrettCom, Inc. reserves the right to change specifications, performance
characteristics and/or model offerings without notice.
www GarrettCom com
..
5
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
2.0 Introduction
2.1 Inspecting the Package and Product
Examine the shipping container for obvious damage prior to installing this
product; notify the carrier of any damage that you believe occurred during shipment or
delivery. Inspect the contents of this package for any signs of damage and ensure that
the items listed below are included.
This package should contain:
1 Magnum 6K16V Managed Fiber Switch, base unit
(configured with user-selected port module options installed)
1 AC Power Cord (U.S. and other 115 VAC only)
1 Set of two metal vertical mounting brackets, with screws to the case
1 Installation and User Guide (this manual)
1 Product Registration Card
Remove the items from the shipping container. Be sure to keep the shipping
container should you need to re-ship the unit at a later date. To validate the product
warranty, please complete and return the enclosed Product Registration Card to
GarrettCom, Inc. as soon as possible.
In the event there are items missing or damaged, contact the party from whom
you purchased the product. If the unit needs to be returned, please use the original
shipping container if possible. Refer to Section 6, Troubleshooting, for specific return
procedures.
www GarrettCom com
..
6
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
2.2 Product Description - Magnum 6K16V Managed Fiber Switch
M
copper ports, 10Mb 100Mb and Gigabit speed ports, and comprehensive management
software in a compact industrial-grade package. Setting a new standard for Industrial and
Carrier Class applications, heavy duty Ethernet Switch jobs are readily accommodated
with an extended temperature rating of -40˚C to 60˚C by the UL Component Parts
method, or -50˚C to 95˚C by the IEC 60068 Type Test method. With options such as all
popular DC power input types, worldwide AC power, and DIN-Rail mounting, the
hardened Magnum 6K16V is a “go-anywhere do-anything” Industrial Ethernet Switch.
The large family of port modules offer the choice of all fiber media (all
connector types, multi- and single-mode) and 10/100 Mb auto-negotiating RJ-45 ports.
Standard GBIC ports can be configured for a variety of Gigabit cabling types and
distances.
High performance features
include non-blocking speed on all ports
and 802.1p QoS Traffic Prioritization.
Magnum 6K16Vs are “plug-and-play”
ready for use as backbone switches
where a mix of bursty data traffic and
priority streaming traffic for VoIP and audio/video applications is present.
agnum 6K16V Managed Fiber Switches provide modularity of fiber and
Magnum 6K16V Fiber Switches are provided with LAN management software
including SNMP, Tag- and Port-based VLANs, IGMP Snooping and Port Security,
control via command line interface. For high availability LANs using ring topologies,
Spanning Tree Protocol, Link-Loss-Learn and S-Ring are available. See the Managed
Networks Software (MNS-6K) and S-Ring datasheets for additional details on the
comprehensive set of software programs and options.
Designed for use in transportation and traffic control systems, power utilities,
industrial factory-floor jobs, and video surveillance systems with segments requiring
Gigabit backbone interconnections, the Magnum 6K16V is easy to install and operate.
The next generation of industrial applications will need advanced managed network
software, operation at extended temperatures, fiber ports modularity, support for self-
healing ring structures, and gigabit backbone configurability. The Magnum 6K16V has
www GarrettCom com
..
7
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
all of these, and is available now.
Magnum 6K16V Managed Fiber Switches have heavy duty metal cases and
auto-ranging power supplies for operation with standard AC power worldwide. Internal
DC power supplies are optional. All DC power input types (5V, 24V, 48V, 125V) are
supported, and dual source input is optional on all except 5VDC..
There are two Alarm Relay contacts provided on each Magnum 6K16V
Switch to monitor basic operations.. One is for hardware, and will signal loss of power
internally. The other is software controllable and will signal user-defined software events
such as a security violation or an S-Ring fault condition.
The wide variety of port modules are key to the flexibility and adaptability.
2.2.1 Eight-port SFF fiber modules (6K8-MTRJ, 6K8-MLC), 100Mb fiber
1 3 5 7
ACT
F/H
ACT
F/H
LK LK LK LK
ACT
F/H
ACT
F/H
LK LK LK LK
2 4 6 8
In an eight-port SFF
fiber port module, all of the fiber
ports are of the same speed
(100Mb), mode, and connector
type. Models are available with
Small Form Factor (SFF) are
1 3 5 7
ACT
F/H
ACT
F/H
ACT
F/H
ACT
LK LK LK LK
F/H
multi-mode MT-RJ or LC-type connectors, and single-mode LC-type connectors.
ACT
F/H
ACT
F/H
ACT
F/H
ACT
F/H
Fig.2.2.2 :
SFF Fiber Port
Modules,
6K8-MTRJ (to the left)
and
6K8-MLC or -SLC
(below)
LK LK LK LK
2 4 6 8
2 4 6 8
ACT
F/H
ACT
F/H
ACT
F/H
ACT
F/H
The 100Mb fiber eight-port modules for the Magnum 6K16V’s normally are
set (factory default) to operate in full-duplex mode for best fiber distance and
performance. Using the 6K16V’s MNS software, the user may select full- or half-duplex
mode per-port through set-up of the software (See Magnum 6K16V MNS Software
Manual) for the flexibility to adapt to any FDX or HDX type of Fast Ethernet devices).
There are three LED’s per fiber port. The Link (LK) LED indicates “ready for
www GarrettCom com
..
8
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
operation” on that port when lit, the F/H LED indicates operation in full-duplex mode
when ON (half-duplex when OFF), and the blinking ACT LED indicates receiving
Activity on the port. A fiber cable must be connected into a SFF port and the Link (LK)
indicator for that port must be ON (indicating there is a powered-up device at the other
end of the cable) in order for a LK LED to provide valid indications of operating
conditions on that port.
2.2.2 Eight-Port Copper Module, 6K8-RJ45
The 6K16V’s 8-
port Copper port module,
model 6K8-RJ45, provides
eight 10/100Mb switched RJ-
45 ports. The 10/100Mb
/100LK10
F/
10/100
switched ports normally (as a
default setting) are
F/H
independently N-way auto-
negotiating for operation at 10 or 100Mb speed in full- or half-duplex mode, i.e., each
independently selects a mode and speed to match the device at the other end of the
twisted pair cable. (See Section 4.3 for auto-negotiation details)
1 3 5 7
H
2 4 6 8
ACT
LK
ACT
On the model 6K8-RJ45 module, there are four LEDs for each port, two in the
connector and two separate. The LK (Link) LED indicates “ready for operation” on that
port when lit. The blinking ACT (Activity) LED indicates receiving Activity on that port
when lit. The 10/100 LED indicates operation at 100Mb speed when ON and at 10 Mb
speed when OFF (when auto-negotiation is not disabled). The FDX/HDX LED is ON to
indicate full-duplex operation and OFF to indicate half-duplex mode. A twisted pair
cable must be connected into an RJ-45 port and the Link (LK) indicator for that port must
be ON (indicating there is a powered-up device at the other end of the cable) in order for
a LK LED to provide valid indications of operating conditions on that port.
Using the 6K16V’s MNS software, the user may disable auto-negotiation and
fix the desired operation of each RJ-45 port. MNS Software set-up may select 10Mb or
100Mb speed and full- or half-duplex mode per-port as per user requirement. (See
Magnum 6K16V MNS Software Manual for details info.).
2.2.3 Six-Port “4 + 2” Combo Modules, 4@ 10/100 RJ-45 and 2@ 100Mb fiber
The combo six-port modules are combinations of copper and fiber media,
www GarrettCom com
..
9
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
available as four 10/100 switched RJ-45 copper ports and two 100Mb switched multi-
mode fiber ST, SC or single mode SC or Long Reach SC ports. For ports numbering,
ports 1,3,5,7 are copper, ports 2 and 6 are fiber, ports 4 and 8 are not present.
1 3 5 7
10/100
F/H
ACT
F/H
LK
2 6TX RX
ACT
F/H
TX LK RX
LK
ACT
1 3 5 7
10/100
F/H
ACT
F/H
LK
2 6TX RX
ACT
F/H
TX LK RX
LK
ACT
4@ RJ-45 + 2@ 100Mb SC
The four RJ-45 ports operate just like the 8-port copper module, and the two fiber ports
operate at 100Mbps full-duplex (default). User mode control per port through the MNS
software is also the same.
On Magnum “4+2” Combo modules, there are four LED’s for each RJ-45 port,
which indicate status the same as described for the 6K8-RJ45 in Section 2.2.3 above. The
fiber port’s LEDs indicate status the same way as described for the SFF fiber modules in
Section 2.2.2 above. Color-coding on the panel of the module shows which LEDs
belong to which port.
The Magnum Combo
10/100
F/H
ACT
F/H
1 3 5 7
ACT
LK
2 6TX RX
F/H
TX LK RX
six-port modules are also available
LK
with 4@ MTRJ 100Mb mm SFF
ACT
fiber and 2@10Mb fiber mm ST
ports, and with 4@ RJ45 10/100
copper and 2@10Mb fiber mm ST
ports. The 4@ RJ-45 + 2@ 10 Mb ST operation of the SFF fiber
and the RJ-45 half of the module is as described for those port types above. For detailed
information about 10Mb mm ST fiber half of the module, see Section 2.2.5.
www GarrettCom com
..
10
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
R
2.2.4 Four-Port 10 Mb
The 4-port @10Mb ST fiber modules behave the same as the 4@100Mb ST
ACT
F/
ACHT
F/
H
and 100Mb mm Fiber ST Modules
ACT
TX RXLK
1 5
2 6
LK
TX RX
ACT
HF/
HF/
TX R XLK
T LK
fiber modules except for the 10Mb speed. For ports numbering, ports 1, 2, 5, 6 are
present, ports 3, 4. 7, 8 are not present. There is also a similar 100Mb fiber SC module.
The default setup on the 10Mb fiber module is half-duplex, which allows the
Magnum 6K16V Switch to connect to any 10Mb hub or media converter or almost any
other device with a 10Mb fiber Ethernet port. The default setting of the 100Mb module is
full duplex. User mode-control per port through the MNS “port settings” software is the
same as the other 6K16V modules.
The fiber ports support fiber cabling distances according to the 10BASE-FL
and 100BASE-FX standards, i.e., 2km distance for multi-mode fiber. (Single-mode for
up to greater distance may be available as a special order, request quote).
2.2.6 Gigabit (1000Mbps) port modules
The Magnum 6K16V offered a wide option Gigabit speed with multiple choice
for the modular slot. While up to two Gigabit modules (maxm.) can be configured in the
modular slot. The Gigabit port option for the modular slot comes in couple of different
configuration. The two Giga port has been offered as GBPM-2OTX (fiber or RJ-45),
whereas the single Gigabit module comes in flavor of G+4(10/100 RJ-45 ports) or G+2
(100Mb fiber ports) as shown below in the figure.
ACT
F/
TX RXLK
ACT
F/
2 6TX RXL
ACT
F/
TX LK RX
ACT
F/
TX R XLK
1 3 5 7
10/100
F/
L
ACT
1@ 1000Mb Fiber SC + 2@ 100Mb SC 1@ 1000Mb Fiber SC + 4@10/ 100Mb
The 6K16V Modules provide a GBIC opening for insertion of industry-standard GBICs
to provide Gigabit (Gb) media flexibility. GBIC models are available for both multi-
mode (550m) and single-mode (10, 25,40,70)km fiber options, and for Gigabit copper as
well, with new models appearing often.
www GarrettCom com
..
11
Magnum 6K16V Managed Fiber Switch Installation and User Guide (06/04)
The 1000Mb Gigabit fiber-port modules on the Magnum 6K16V are normally
set (factory default) to operate in full-duplex mode for best fiber distance and
performance. The 1000Mbps SC fiber-optic module on the Gigabit -SX and Gigabit-LX
transceivers are compatible with the IEEE 802.3z Gigabit standards.
There are two LEDs mounted on each Gigabit port module. The Gigabit fiber
port is fixed at 1000Mbps speed full-duplex mode at all times and has LEDs that indicate
LK (Link status) and ACT (receiving activity) on that port when lit.
2.2.6 Packet Prioritization, 802.1p QOS
Quality of Service means providing consistent predictable data delivery to
users from datagram paths that go all across a network. As a LAN device, the Magnum
6K16V can do its part to prevent any QOS degradation while it is handling Ethernet
traffic through its ports and buffers.
The Magnum 6K16V switching hardware supports the IEEE 802.1p standard
and fulfills its role in support of QOS, giving packet processing priority to priority tagged
packets according to the 802.1p standard. In addition to hardware support for QOS, the
MNS software (R2) supports two priority queues that can be shared across the eight
levels of defined packet priorities for application-specific priority control by the user
through software configuration settings.
2.2.7 Frame Buffering and Flow Control
Magnum 6K16V’s are store-and-forward switches. Each frame (or packet) is
loaded into the Switch’s memory and inspected before forwarding can occur. This
technique ensures that all forwarded frames are of a valid length and have the correct
CRC, i.e., are good packets. This eliminates the propagation of bad packets, enabling all
of the available bandwidth to be used for valid information.
While other switching technologies (such as "cut-through" or
"express") impose minimal frame latency, they will also permit bad frames to propagate
out to the Ethernet segments connected. The "cut-through" technique permits collision
fragment frames (which are a result of late collisions) to be forwarded which add to the
network traffic. Since there is no way to filter frames with a bad CRC (the entire frame
must be present in order for CRC to be calculated), the result of indiscriminate cut-
through forwarding is greater traffic congestion, especially at peak activity. Since
collisions and bad packets are more likely when traffic is heavy, the result of store-and-
forward operation is that more bandwidth is available for good packets when the traffic
www GarrettCom com
..
12
Loading...