Gardena FP 750 E, FP 1000 E, FP 1800 E, FP 1400 E, FP 2500 E Operating Instructions Manual
...
FP 750 E Art. 7650
FP 1000 E Art. 7651
FP 1400 E Art. 7652
FP 1800 E Art. 7653
FP 2500 E Art. 7654
FP 4000 E Art. 7655
FP 5000 E Art. 7656
FP 7500 E Art. 7657
GARDENA
®
D Betriebsanleitung
Wasserspielpumpen-Set
GB Operating Instructions
Fountain Pump Set
F Mode d’emploi
Pompe pour jets d’eau
NL Instructies voor gebruik
Waterspelpomp-set
S Bruksanvisning
Fontän Pump Set
I Istruzioni per l’uso
Pompa per giochi d’acqua
E Manual de instrucciones
Bomba para juegos de agua
P Instruções de manejo
Bomba para fontes
DK Brugsanvisning
Springvandspumpesæt
D
GBFNLS
I
E
P
DK
GARDENA Fountain Pump Set
FP 750 E / FP 1000 E / FP 1400 E / FP 1800 E / FP 2500 E
FP 4000 E / FP 5000 E / FP 7500 E
Welcome to the Garden of GARDENA ...
Translation of the original instructions from German. Please read
these operating instructions carefully and observe the notes given.
Use the instructions to familiarise yourself with the equipment, the
operating controls, their correct use, and the notes on safety.
For safety reasons, children under 16 as well as persons not
familiar with these operating instructions must not use this
Fountain Pump Set.
v Keep these operating instructions in a safe place.
1. Where to use Your GARDENA Fountain Pump Set
. . . . . . . . . . . 9
2. For Your Safety
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4. Initial Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5. Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6. Trouble-shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7. Storing your Fountain Pump Set
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
8. Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
9. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
10. Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Where to use Your GARDENA Fountain Pump Set
GARDENA Fountain Pumps have been designed for private use.
They are not designed for operating watering tools and systems.
The pumps may be used indoors as well as outdoors.
GARDENA Fountain Pumps have not been designed for constant use in the industrial sector. Corrosive, easily combustible,
aggressive or explosive substances (e.g. petrol, petroleum, nitro
thinner) as well as salt-water or food / drinking water must not
be pumped.
Intended Use
Please note
2. For Your Safety
Electrical Safety:
The pump should be operated via a residual
current device with a residual current rating of
≤ 30 mA (DIN VDE 0100-702 and 0100-738).
The pump must be placed on solid, even
ground.
v Please ask your electrician for his advice.
Always disconnect the pump from the
mains before undertaking any work on it.
Mains power cables should not have a smaller
cross-section than a rubber sheathed cable of
the designation H05 RN-F 3G0,75 (FP 4000 E,
FP 5000 E, FP 7500 E0: H05 RN-F 3G1,0).
Extension cables must meet the requirements
of DIN VDE 0620.
Check line voltage. Data indicated on the type
plate must match technical data of the mains
supply.
Contents
9
GB
10
GB
The pump must not be operated when there
are people in the water. Swimming pools and
garden ponds should be designed according to
international and national design regulations.
v Please consult a professional electrician.
For Austria:
Pumps for use on swimming pools and on
ponds may only be operated via an isolating
transformer.
v Please consult a professional electrician.
For Switzerland:
In Switzerland mobile appliances which are
used outdoors, must be connected via a residual-current device.
Note:
Do not allow the pump to run without water
because dry-running leads to an undesirable build up of heat.
Before operating the pump, look to see if there
is any damage to the pump (esp. regarding
power cable and plug). The connection cable
of the pump cannot be replaced. If the cable is
damaged the pump must be scrapped. Ensure
that the power cable cannot be crushed if it
has not been laid in conduit in the earth or in
gravel.
Do not use the power cable to carry the pump
or to pull the plug out of the socket.
Protect the power cable from heat, oil and
sharp edges.
The temperature of the liquid used must not
be below 4 °C or above 35 °C.
Sand and other abrasive substances in the
liquid cause increased wear and reduce the
output of the pump.
Please observe the local noise prevention
regulations.
All pumps
(a cascade
art. 7650
(b Waterbell
-
7654
(c jets of
water
art. 7655
-
7657
(d foaming -
spring
3. Assembly
To provide a firmer mounting, the filter housing can be attached to
a solid base (e.g. paving stone).
1. Screw nozzle pipe
1
on to the pump with the ball and socket
joint.
2. Screw the water feature insert you require (a / (b / (c / (d on
the nozzle pipe 1.
2
Holder for GARDENA underwater light art 7951
The additional filter can be fitted on the filter housing to extend the
maintenance interval and to give the water feature a longer life.
1. Remove the cap
3
from the pump.
2. Fit both filter shells 4on the filter housing 5and clip into
place.
3. Press sealing cover
3
on to the additional filter 4.
You can install additional filters
z
4a
to increase the filter surface.
Additional filters are available from GARDENA Service.
Fit the pump:
VARIANT 1 : Mount the
additional filter on the pump:
2
1
5
3
4
z
4a
11
GB
The additional filter can be installed as a pond edge controller for
adjusting water features and cleaning the filter housing from the
edge of the pond. Water is only drawn in via the additional filter.
You can connect the following hoses to the hose connection:
.
3/4” and 1” for FP 750 E / FP 1000 E / FP 1400 E / FP 1800 E /
FP 2500 E
.
11/4” and 1 1/2” for FP 4000 E / FP 5000 E / FP 7500 E
For best results use a hose with the largest possible diameter.
1. Remove the cap
3
from the pump.
2. Press in snap fastenings
6
and
open up the filter housing 5.
3. Push the hose connection
7
on to the pump.
4. Close filter housing 5.
5. Insert hose connection 8in
to one filter shell 4and snap
into the second filter shell
4
.
6. Press sealing cover 3on to
the pond edge control 4.
7. Connect water feature pump
and pond edge control to a
hose.
4. Initial Operation
1. Place water feature pump on a firm base in such a way that the
filter housing 5is completely covered by water.
2. Pull telescopic pipe 9out to the desired length.
3. Netzstecker in eine Wechselstromsteckdose einstecken.
Warning: Pump will start immediately.
4. Set the quantity of water required for the water feature using the
regulator
0
.
5. Water bell: Screw insert into the water feature until the water
feature has produced the shape required.
TIP: Install the pond edge controller on a bed of gravel to
improve the water intake. The regulating valve
0
must be fully
open when using the pond edge controller.
1. Fill hose with water to remove any cushions of air in the hose.
2. Secure the pond edge controller at the edge of the pond (using
rocks, for example).
The pond edge control must be completely covered with water.
3. Set the quantity of water required for the water feature with the
regulator
A
.
Switch on water
feature pump:
Start pond edge control:
VARIANT 2 : Mount the pond
edge controller:
0
A
9
5
0
9
5
4
3
8
7
7
3
5
6
Loading...