Ganz ZNT6-PAT1FN20-N User Manual
Document No: 1018761
Revision: B
Ganz Thermal Series
P a n & T i l t , F i x e d F o c u s T h e r m a l I P a n d A n a l o g C a m e r a
U s e r M a n u a l
Revision Number
Release Date
Description
A
2/05/14
Initial Release
B
7/09/14
Changes/Additions
©Copyright 2013, CBC AMERICA Corp. - All rights reserved.
55 Mall Drive
Commack, NY 11725
800.422.6707
www.GanzSecurity.com
The contents of this document may not be reproduced in whole or in part without the
written consent of the copyright owner.
Rev History
Ganz Thermal Series User Manual
i
NOTICE
ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL
ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF
ANY KIND. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT
FILES AND SOFTWARE ARE PROVIDED “AS IS” WITH ALL FAULTS. CBC AMERICA
Corp DISCLAIMS ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE
OF DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CBC AMERICA Corp BE LIABLE FOR ANY INDIRECT, SPECIAL,
CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION,
LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR
INABILITY TO USE THIS MANUAL, EVEN IF CBC AMERICA Corp HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING
PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH
THE PRODUCT AND ARE LOCATED HEREIN ON PAGE ii
Ganz Thermal Series User Manual
ii
CBC AMERICA CORP.
END USER LICENSE AGREEMENT
FOR
GANZ THERMAL SERIES OF PRODUCTS
THIS LICENSE AGREEMENT IS PROOF OF YOUR RIGHT TO USE THE GANZ THERMAL® SOFTWARE CONTAINED IN THE
CBC AMERICA CORP GANZ THERMAL® SERIES OF PRODUCTS (THE “PRODUCTS”) AND PROVIDES ADDITIONAL
INFORMATION CONCERNING CBC AMERICA CORPS' LIMITED WARRANTY AND LIMITATIONS OF LIABILITY. PLEASE
READ IT CAREFULLY. BY ACCEPTING OR USING THE PRODUCTS, YOU ARE AGREEING TO BE BOUND BY THE TERMS
AND CONDITIONS OF THIS LICENSE AGREEMENT.
This License Agreement (hereinafter the "Agreement") is between you (either an individual or an entity) and CBC
AMERICA Corp. and/or its affiliates ("Ganz"). CBC AMERICA Corp is willing to grant you the following rights to
use the GANZ THERMAL® SOFTWARE incorporated in or supplied with the Products (collectively, the "Ganz
Thermal Software") only if you agree to be bound by all of the terms and conditions of this Agreement. By
accepting or using the Products, you agree to be bound by all the terms and conditions of this Agreement. If
you do not agree to be bound by all of the terms and conditions of this Agreement, CBC AMERICA Corp is
unwilling to grant you any rights to use the Ganz Thermal Software; instead you must promptly return the
Products to CBC AMERICA Corp for a full refund or to the authorized reseller that provided you with the
Products.
1. OWNERSHIP: The Ganz Thermal Software is and shall remain a proprietary product of CBC AMERICA CORP or its licensors and
you hereby acknowledge and agree that the Ganz Thermal Software embodies valuable trade secrets proprietary to CBC AMERICA
CORP and/or its licensors. All patents, copyrights, trademarks, trade names, trade secrets and other proprietary rights relating to or
residing in the Ganz Thermal Software shall be owned or licensed exclusively by CBC AMERICA CORP. Except for the license provided
in Section 2, you shall have no right, title or interest in or to the Ganz Thermal Software. The Ganz Thermal Software is licensed, not
sold, to you for use only under the terms and conditions of this Agreement. Furthermore, you agree to be bound by the terms and
conditions of this Agreement with respect to any and all upgrades or updates to the Ganz Thermal Software provided to you by CBC
AMERICA CORP or the authorized reseller that provided you with the Products.
2. GRANT OF LICENSE: Subject to your full compliance with all terms and conditions set forth in this Agreement, CBC AMERICA CORP
grants you a nontransferable (except as specifically set forth in this Section) non-exclusive, restricted right to use the Ganz Thermal
Software as incorporated in or supplied with the Products and solely in connection with the use of the Products. You may make a
reasonable number of back-up copies of the Ganz Thermal Software. You understand that CBC AMERICA CORP may update the Ganz
Thermal Software at any time and in doing so incurs no obligation to furnish such updates to you pursuant to this Agreement. You may
transfer the license to use the Ganz Thermal Software only in connection with a sale or transfer of the Products and only as included
with the Products and not on a stand-alone basis, provided the buyer or transferee agrees in writing to be bound by all the terms and
conditions of this Agreement.
3. RESTRICTIONS/LIMITATIONS: Except as expressly authorized in Section 2, you may not use, copy, modify, create derivative works
of, distribute, sell, assign, pledge, sublicense, lease, loan, rent, timeshare, or disclose the Ganz Thermal Software, in whole or in part,
at any time for any reason, nor permit any other party to do any of the foregoing. You specifically agree that you will not provide access
to the Ganz Thermal Software to any person or party other than for the intended use of the Ganz Thermal Software as authorized
hereunder. You may not remove from the Ganz Thermal Software, or alter, any of the trademarks, trade names, logos, patent or copyright
notices or markings, or add any other notices or markings to the Ganz Thermal Software. You may not install or use the Ganz Thermal
Software on any product other than the Products. You specifically agree not to reverse engineer, decompile, disassemble, or reverse
translate the Ganz Thermal Software or any part thereof. The license granted in Section 2 shall immediately terminate if you use the
Ganz Thermal Software in a manner that exceeds the scope of the license granted hereunder and/or upon any breach of the terms and
conditions of this Agreement.
4. LIMITED WARRANTY: CBC AMERICA CORP does not warrant that the functions contained in the Ganz Thermal Software will meet
your requirements or that the Ganz Thermal Software will be uninterrupted or error-free. CBC AMERICA CORP warrants that for a period
of twenty-four (24) months from the original shipment date that the Ganz Thermal Software will perform substantially as described in the
applicable Software User Manual during normal use. This limited warranty is void if failure of the Ganz Thermal Software to conform to
the warranty has resulted from improper installation, testing, misuse, neglect, accident, fire or other hazard, or any breach of this
Agreement.
5. LIMITED REMEDIES: In the event of a breach of the foregoing limited warranty, CBC AMERICA CORP will, at its own expense, use
commercially reasonable efforts to promptly and diligently correct all issues with the Ganz Thermal Software (except those classified as
Class 3 issues, which means cosmetic and minor anomalies; functionality is impaired). CBC AMERICA CORP's sole and exclusive
obligation and your sole and exclusive remedy shall be, at CBC AMERICA CORP's sole discretion, to repair or replace the nonconforming
Ganz Thermal Software.
6. NO OTHER WARRANTIES: OTHER THAN THE FOREGOING LIMITED WARRANTY, CBC AMERICA CORP HEREBY
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. SOME JURISDICTIONS DO NOT ALLOW
THE DISCLAIMER OF IMPLIED WARRANTIES, SO THE ABOVE DISCLAIMER MAY NOT APPLY TO YOU, IN WHICH CASE THE
DURATION OF ANY SUCH IMPLIED WARRANTIES IS LIMITED TO SIXTY (60) DAYS FROM THE DATE THE PRODUCTS IS
RECEIVED BY YOU.
7. INTELLECTUAL PROPERTY: Up to the aggregate limit specified in Section 8 below, CBC AMERICA CORP shall indemnify, defend
and hold you harmless against and pay all costs and damages awarded against you resulting from a claim that the Ganz Thermal
Software infringes any U.S. patent or copyright or misappropriates a U.S. trade secret, provided that you (a) provide CBC AMERICA
CORP with written notice of such claim within thirty (30) days of being notified of the claim; (b) allow CBC AMERICA CORP to exclusively
control the defense and/or settlement of such claim; and (c) provide any information, authority and assistance that CBC AMERICA CORP
reasonably deems necessary for the defense and/or settlement of any such claim, provided that any reasonable costs and expenses
incurred by you in providing such information and assistance will be reimbursed by CBC AMERICA CORP. You agree not to consent to
any judgment or decree or do any other act in compromise of any such claim without first obtaining CBC AMERICA CORP's written
consent. In any action based on such a claim, CBC AMERICA CORP may, in its sole discretion and at its own expense, either: (1)
procure for you the license right to continue using the Ganz Thermal Software; or (2) replace or modify the Ganz Thermal Software to
avoid the claim. If neither of the foregoing is reasonably practicable, CBC AMERICA CORP may terminate the license and refund the
license amount paid. CBC AMERICA CORP will not be liable for any costs or expenses incurred by you in connection with any claims
Ganz Thermal Series User Manual
iii
GSOAP
http://www.genivia.com/Products/gsoap/contract.h® l
H.264 encoder
http://www.mpegla.com/main/programs/AVC/Pages/AgreementExpress.a
spx
ONVIF™
www.onvif.org
H.264 decoder (Video LAN
SW)
(VLC provides SourceFreeware)
http://www.gnu.org/licenses/gpl.h® l
Live 555 server
http://www.live555.com/liveMedia/#license
Linux kernel
http://www.kernel.org
Lighttpd
http://www.lighttpd.net/
dhcpcd
http://www.phystech.com/download/dhcpcd.h® l
ntpclient
http://doolittle.icarus.com/ntpclient/
zeroconfig
http://avahi.org/wiki/AboutAvahi
esmtp
http://sourceforge.net/projects/esmtp/
subject to the terms of this Section without the prior written authorization by CBC AMERICA CORP. Notwithstanding the provisions of
this Section, CBC AMERICA CORP assumes no liability or obligation to indemnify for any infringement or misappropriation claim of any
kind arising from: (a) use or combination of the Ganz Thermal Software with other software or products not provided by CBC AMERICA
CORP, if such infringement claims would not have arisen with respect to the Ganz Thermal Software standing alone, or (b) any
modifications, enhancements or revisions to the Ganz Thermal Software unless made or approved in writing by CBC AMERICA CORP.
The foregoing provisions state the entire liability and obligations of CBC AMERICA CORP and the sole and your exclusive remedy with
respect to any actual or alleged infringement or misappropriation of any intellectual property rights regarding or involving the Ganz
Thermal Software.
8. LIMITATION OF LIABILITY: THE AGGREGATE LIABILITY OF CBC AMERICA CORP OR ITS SUPPLIERS IN CONNECTION WITH
THIS AGREEMENT AND THE GANZ THERMAL SOFTWARE, REGARDLESS OF THE FORM OF THE ACTION GIVING RISE TO
SUCH LIABILITY (WHETHER IN CONTRACT, TORT OR OTHERWISE), SHALL NOT EXCEED THE AMOUNT PAID BY YOU TO CBC
AMERICA CORP OR RESELLER FOR THE PRODUCTS, OR USD $100,000.00, WHICHEVER IS LESS. NEITHER CBC AMERICA
CORP NOR ITS SUPPLIERS SHALL BE LIABLE TO YOU FOR ANY INDIRECT, EXEMPLARY, SPECIAL (INCLUDING PUNITIVE OR
MULTIPLE), CONSEQUENTIAL OR INCIDENTAL DAMAGES OF ANY KIND (INCLUDING WITHOUT LIMITATION LOSS OF DATA,
EQUIPMENT DOWNTIME OR LOST PROFITS), EVEN IF CBC AMERICA CORP OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. THE LIMITED WARRANTY, LIMITED REMEDIES AND LIMITED LIABILITY PROVISIONS
CONTAINED IN THIS AGREEMENT ARE FUNDAMENTAL PARTS OF THE BASIS OF CBC AMERICA CORP’ BARGAIN
HEREUNDER, AND CBC AMERICA CORP WOULD NOT PROVIDE THE GANZ THERMAL SOFTWARE TO YOU ABSENT SUCH
LIMITATIONS.
9. U.S. GOVERNMENT END USERS: This provision only applies to u.s. Government end users. The GANZ THERMAL
SOFTWARE and any provided documentation are commercial items as that term is defined at 48 C.F.R. Part 2.101, consisting of
"commercial computer software" and "computer software documentation" as such terms are defined in 48 C.F.R. Part 252.2277014(a)(1) and 48 C.F.R. Part 252.227-7014(a)(5), and used in 48 C.F.R. Part 12.212 and 48 C.F.R. Part 227.7202, as applicable.
Consistent with 48 C.F.R. Part 12.212, 48 C.F.R. Part 252.227-7015, 48 C.F.R. Part 227.7202-1 through 227.7202-4, 48 C.F.R. Part
52.227-19, and other relevant sections of the Code of Federal Regulations, as applicable, and as may be amended or updated from
time-to-time, the GANZ THERMAL
end users (a) only as commercial items, and (b) with only those rights as are granted to all other end users pursuant to the terms and
conditions contained herein. The GANZ THERMAL
C.F.R. Part 252.227-7014(a)(14).
10. THIRD PARTY SOFTWARE LICENSES: The Ganz Thermal Software may contain third party software, which requires the
application of third party terms and conditions (reference Table 1 below). Such third party terms and conditions are located in .txt files or
other documentation of each third party software component. By accepting this Agreement, you also agree to accept and be bound by
any such applicable third party additional terms and conditions, if any, as referenced herein.
11. GENERAL: This Agreement shall be governed by and interpreted in accordance with the laws of the state of New York, U.S.A.,
excluding its conflict of laws principles. The United Nations Convention on Contracts for the International Sale of Goods is specifically
disclaimed. If any provision of this Agreement is held by a court of competent jurisdiction in the United States to be unenforceable for
any reason, the remaining provisions hereof shall be unaffected and remain in full force and effect as if this Agreement had been
executed with the invalid portion eliminated, provided the effectiveness of the remaining portions of this Agreement will not defeat the
overall intent of the parties. In such a situation, the parties agree, to the extent legal and possible, to incorporate a replacement provision
to accomplish the originally intended effect. This Agreement is the final, complete and exclusive agreement between the parties relating
to the subject matter hereof, and supersedes all prior or contemporaneous understandings and agreements relating to such subject
matter, whether oral or written, and may only be modified by a written instrument executed by an authorized representative of each
party.
®
SOFTWARE and any provided documentation are distributed and licensed to U.S. Government
®
SOFTWARE is provided with Restricted Rights, as such term is defined in 48
®
Table i: 3rd Party Software License
Ganz Thermal Series User Manual
iv
RE G U L A TOR Y AND SA FE T Y
FCC
This equipment has been tested and found to comply with the limits of FCC Class A Part
15 Subpart B. This equipment also complies with Canadian CES-003.
WARNING
This is a Class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
CE
This equipment complies with CE standard as below.
For Europe (CE):
IEC 60065:2001 + Amd 1:2005 / EN 60065:2002
UL
This equipment is approved by UL and is compliant to below specifications.
For North America (UL):
UL 60065, 7th Edition, 2007-12-11
CAN/CSA-C22.2 No. 60065-03, 1st Edition, 2006-04 + A1:2006
RoHS
This equipment complies with the European ROHS directive, 2011-65-EC.
WEE
This equipment must be disposed of as electronic waste. Contact your nearest CBC
AMERICA Corp Representative for instructions on how to return the product for proper
disposal.
Ganz Thermal Series User Manual
v
TA B L E OF CONTE N T S
1 Introduction .................................................................................................................1
1.1 Document Overview .................................................................................................... 1
2 Product Overview ........................................................................................................2
2.1 IP Camera Overview ................................................................................................... 2
2.2 Camera Hardware ....................................................................................................... 4
3 Specifications ..............................................................................................................6
3.1 Quick Reference Specifications ................................................................................... 6
3.2 Range Performance .................................................................................................... 8
4 Installation and Access ............................................................................................. 10
4.1 Package Contents ..................................................................................................... 10
4.2 Installation ................................................................................................................. 10
4.3 Installation Procedure ................................................................................................ 11
4.4 Prepare Cables and Gland ........................................................................................ 12
4.5 Assembly ................................................................................................................... 15
4.6 Mounting the Camera ................................................................................................ 17
4.7 Access ...................................................................................................................... 17
4.8 Login to the IP Camera .............................................................................................. 18
4.9 Log Out ..................................................................................................................... 19
5 Configuration and Management ................................................................................ 20
5.1 Ganz Thermal Web Interface and Access Privilege ................................................... 20
5.2 Setup ......................................................................................................................... 21
6 Use and Application .................................................................................................. 35
6.1 Live Video ................................................................................................................. 35
6.2 PTZ ........................................................................................................................... 38
6.3 Motion Detection ....................................................................................................... 39
6.4 Video Storage ........................................................................................................... 41
7 Maintenance ............................................................................................................. 43
7.1 System Status ........................................................................................................... 43
7.2 Restart Camera ......................................................................................................... 44
7.3 Restore Factory Defaults ........................................................................................... 45
7.4 Format Local Storage ................................................................................................ 45
7.5 System Update ................................................................................................ .......... 46
7.6 Camera Functions ..................................................................................................... 46
7.7 Log ............................................................................................................................ 48
7.8 Copyright ................................................................................................................... 48
8 Interoperability .......................................................................................................... 49
9 Maintenance and Troubleshooting ................................................................ ............ 50
9.1 Maintenance .............................................................................................................. 50
9.2 Recommended Care ................................................................................................. 50
9.3 Troubleshooting ......................................................................................................... 50
10 Warranty ................................................................................................................... 52
11 Support ..................................................................................................................... 53
Ganz Thermal Series User Manual
vi
TA B L E OF FIGU R E S
Figure 1: Ganz Thermal® Camera ................................................................................................................... 4
Figure 2: Ganz Thermal® Camera Mount ........................................................................................................ 4
Figure 3: Ganz Thermal® Bottom View ........................................................................................................... 5
Figure 4: Ganz Thermal® ZNT6-Pxx1 Range Data ......................................................................................... 8
Figure 5: Ganz Thermal® ZNT6-Pxx2 Range Data ......................................................................................... 9
Figure 6: Recommended Tool Kit .................................................................................................................. 12
Figure 7: Recommended Analog Tools ......................................................................................................... 12
Figure 8: Analog and Ethernet Cable through the Gland .............................................................................. 14
Figure 9: Push Gland over the Cables .......................................................................................................... 14
Figure 10: Push Gland into Gland Housing ................................................................................................... 14
Figure 11: Tighten Gland Nut & Terminate Cables ....................................................................................... 15
Figure 12: ZNT6-P Pin-Out (Pin 1: 24 VAC, Pin 2: 24 VAC, Pin 3: 12-24 VDC, Pin 4: GND) ..................... 16
Figure 13: ZNT6-P RS-485 Pin-Out (Pin 1: NEG, Pin 2: POS, Pin 3: GND) ................................................ 16
Figure 14: Camera mounted to a Ganz Thermal® Wall Bracket ................................................................... 17
Figure 15: Camera Discovery with Windows 7.............................................................................................. 18
Figure 16: Login Prompt ................................................................................................................................ 18
Figure 17: Ganz Thermal Web Interface ....................................................................................................... 21
Figure 18: Ganz Thermal Web Interface Setup Menu .................................................................................. 21
Figure 19: TCP/IP Settings ............................................................................................................................ 22
Figure 20: FTP Settings ................................................................................................................................. 23
Figure 21: Email Settings .............................................................................................................................. 24
Figure 22: Ping Target ................................................................................................................................... 25
Figure 23: 802.1X .......................................................................................................................................... 26
Figure 24: Zero Network Configuration ......................................................................................................... 26
Figure 25: User Accounts .............................................................................................................................. 27
Figure 26: Camera Date and Time settings .................................................................................................. 28
Figure 27: Video Streaming ........................................................................................................................... 30
Figure 28: Motion Detection .......................................................................................................................... 31
Figure 29: Video Settings .............................................................................................................................. 32
Figure 30: Pelco-D ......................................................................................................................................... 33
Figure 31: Analog Video Output .................................................................................................................... 33
Figure 32: PTZ Control .................................................................................................................................. 34
Figure 34: Live Video and View Menu ........................................................................................................... 37
Figure 35: PTZ Settings ................................................................................................................................. 39
Figure 36: Motion Detection .......................................................................................................................... 41
Figure 37: Video Archive Menu ..................................................................................................................... 42
Figure 38: System Status .............................................................................................................................. 44
Figure 39: Restart Camera ............................................................................................................................ 45
Figure 40: Restore Factory Defaults ............................................................................................................. 45
Figure 41: Formal Local Storage ................................................................................................................... 46
Figure 42: System Update ............................................................................................................................. 46
Figure 43: Heater Control .............................................................................................................................. 47
Figure 44: Auto Calibration Interval ............................................................................................................... 47
Figure 45: Constant Recording ..................................................................................................................... 48
Ganz Thermal Series User Manual
vii
LI S T OF TA BLE S
Table 1: Ganz Thermal® Connections ............................................................................................................. 5
Table 2: Ganz Thermal® Series Specification Quick Reference Table............................................................ 6
Table 3: Camera Main Menu and Access Privileges using the Ganz Thermal Web Interface ..................... 20
Table 4: Network TCP/IP Settings ................................................................................................................. 22
Table 5: FTP Server ...................................................................................................................................... 23
Table 6: Email Server .................................................................................................................................... 24
Table 7: 802.1X ............................................................................................................................................. 25
Table 8: Accounts and Users ........................................................................................................................ 27
Table 9: Date and Time ................................................................................................................................. 28
Table 10: Video Streaming ............................................................................................................................ 29
Table 11: Motion Detection............................................................................................................................ 31
Table 12: Video Settings ............................................................................................................................... 32
Table 13: Pelco-D .......................................................................................................................................... 32
Table 14: PTZ Control ................................................................................................................................... 34
Table 15: Live Video and Controls ................................................................................................................ 35
Table 16: RTSP URIs .................................................................................................................................... 37
Table 17: PTZ Settings .................................................................................................................................. 38
Table 18: Motion Detection............................................................................................................................ 40
Table 19: Video Storage and Recording ....................................................................................................... 41
Table 20: System Status ............................................................................................................................... 43
Table 21: Troubleshooting Symptoms, Causes and Recommendation ........................................................ 51
Ganz Thermal Series User Manual
viii
Abbreviation
Description
VOx
Vanadium Oxide
IP
Internet Protocol
ICE™
Image Contrast
Enhancement
ONVIF™
Open Network Video
Interface Forum
NEDT
Noise Equivalent Delta
Temperature
DHCP
Dynamic Host Control
Protocol
TCP
Transmission Control
Protocol
UDP
User Datagram Protocol
FTP
File Transfer Protocol
NTP
Network Time Protocol
HTTP
Hypertext Transport
Protocol
HTTPS
Hypertext Transport
Protocol Secure
802.1X
Network Access Control
Port based standard
H264
Video Compression
Standard
JPEG
Joint Photographic Experts
Group
MJPEG
Motion Joint Photographic
Experts Group
VLC
VideoLAN Client
AGC
Automatic Gain Control
ROI
Region of Interest
RTP
Realtime Transport
Protocol
RTSP
Realtime Streaming
Protocol
UPnP
Universal Plug and Play
EULA
End User Licensing
Agreement
AC R O N YM S A N D AB B REV I A TION S
Ganz Thermal Series User Manual
ix
RE F E R ENC E DOC U M E NTA T I O N
The following documents form part of this user manual. In the event of a conflict between
documents referenced herein and the contents of this user manual, please refer to the
content of the most recently released document.
Ganz Thermal® Quick Start Guide
Ganz Thermal WinXP UPnP Procedure
Ganz Thermal® IP Series Interface Control document (ICD)
http://www.GanzSecurity.com
CBC AMERICA Corp Training Videos
http://www.youtube.com/channel/UCM673QrTQ5uIxNktUnC0Dsg
VLC Media Player Download (Version 2.0.0 Recommneded)
http://www.videolan.org/vlc/
Ganz Thermal Series User Manual
x
SA F E T Y IN S TRU C T I O NS
NOTIFICATIONS: CAUTION, WARNING AND NOTE
Throughout this manual, notifications are used to alert the user’s to potential risks and to
minimize the potential for personal injury and or damage to the product. When a notification
is present, it is important that the user review and understand all statements related to the
notification before proceeding. If questions arise, please contact your authorized dealer or
CBC AMERICA Corp.
Notifications are preceded by a symbol and followed by highlighted text. Three types of
notifications are used throughout this manual and are defined below:
CAUTION
A caution is a procedure, practice, or condition that, if not strictly followed, may
result in personal injury or damage to the equipment that may impede product
performance.
A warning is intended to alert the user to the presence of potentially harmful
circumstances and provide precautionary guidance for mitigating risk of
personal injury and or damage to the product.
A note is a statement that clarifies or is used to emphasize important
information.
WARNING
NOTE
Ganz Thermal Series User Manual
xi
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Install in accordance with the manufacturer’s instructions.
6. Installation of the equipment must comply with local and national
electrical codes.
7. This product must be connected to a Power Over Ethernet IEEE
802.af compliant power source or a UL Listed “Class 2” power supply
rated 12-24 V DC or 24 V AC minimum 13 W or 0.54 A.
WARNING
8. Operating the camera at voltage levels outside the specified range
may result in permanent damage to the unit and void the product
warranty.
9. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
10. Clean the camera lens only with lens cleaning paper.
11. Failure to follow the proper procedure may cause permanent damage
to the camera and void the product warranty.
Ganz Thermal Series User Manual
xii
This page intentionally left blank.
Ganz Thermal Series User Manual
1
1 IN T R O DUC T I ON
1.1 DOCUMENT OVERVIEW
This document, provides details about the IP Camera features, installation, access,
configuration, application, interoperability, troubleshooting, warranty and support of the
Ganz Thermal® ZNT6-P Series Pan and Tilt, Fixed Focus Thermal IP and Analog Cameras.
Ganz Thermal Series User Manual
2
2 PR O D U C T OV ERV I E W
2.1 IP CAMERA OVERVIEW
This manual applies to the following products:
Ganz Thermal® ZNT6-Pxx1 30 Hz
Ganz Thermal® ZNT6-Pxx1 9 Hz
Ganz Thermal® ZNT6-Pxx2 30 Hz
Ganz Thermal® ZNT6-Pxx2 9 Hz
This chapter provides an overview of the Ganz Thermal® ZNT6-P Series, a Pan & Tilt,
Fixed Focus Thermal IP and Analog Camera. The Ganz Thermal® ZNT6-P Series offers a
feature-rich thermal camera solution for video surveillance systems. The Ganz Thermal
ZNT6-P Series is available in 2 frame rates (versions), 30Hz and 9Hz. The Ganz Thermal®
ZNT6-P Series employs DRS’s proven uncooled 320 x 240, 17 μm VOx thermal imaging
technology. Unlike many conventional and low light video surveillance cameras, the Ganz
Thermal® ZNT6-P Series does not require any ambient light or illumination. It detects
infrared (heat) waves in the 8-14 µm wavelength in the Electromagnetic spectrum to
provide users with superior thermal images in challenging environments, including
complete darkness, over water and in dark corners, where threats are difficult to detect
due to lighting constraints and weather conditions.
®
The camera system is an Internet Protocol (IP) networked solution, conforming to the Open
Network Video Interface Forum (ONVIF™) standard and is operational in a networked
environment through a central office, remote video management system or through the
provided Ganz Thermal web interface utility. With an industry leading low power
consumption of less than 12.95 watts, the Ganz Thermal® ZNT6-P Series is IEEE802.3af
compliant, supporting video, camera control and power over a single tamper resistant
cable connection. As a result, the camera can be configured and installed easily into any
existing security infrastructure.
Measuring approximately 20 x 27 cm (diameter x height) and weighing less than 3
kilograms, the Ganz Thermal® ZNT6-P Series is compact and lightweight. It is sealed to
an IP66 outdoor rating when installed in the “ball-down” configuration, which makes it ideal
for outdoor security of critical infrastructure such as airports, utility companies, and nuclear
power plants. The camera is available with a choice of fully sealed and hard carbon coated
athermalized fixed focus lenses, which provide a horizontal field of view of 90°, 40°, 16°,
or 9° for ZNT6-Pxx1 models and 90°, 44°, 37.5°, 24.8°, or 17.6° for ZNT6-Pxx2 models,
and are all capable of 4X digital zoom.
The Thermal IP camera includes the following key features:
Thermal Imaging – Provides superior thermal imaging capabilities in
complete darkness and challenging environments 24 hours a day 7 days
a week using patented DRS sensor technology.
Superior image quality with Image Contrast Enhancement (ICE) feature
Optimized Lens – The lens material and optical design is optimized for
thermal imaging and range performance.
Ganz Thermal Series User Manual
3
Outdoor ready – Suitable for outdoor deployment out-of-the box with a
built-in heater, anti-ice and anti-fog, and IP66 ready.
Local Storage – Comes with a built-in memory for storage of video
Power options – The IP camera can be powered with 12/24 volts DC or
24 volts AC, which is provided through an optional external power
adapter, or through PoE (802.3af), which is provided through a
supported switch.
Communications Interface – 10/100 Ethernet and Power Over Ethernet
(POE).
DHCP support – The IP camera can automatically obtain its IP address
in a network in which DHCP is enabled.
Multiple protocol support –Supports DHCP, FTP, HTTP, HTTPS, NTP,
SMTP, RTP, RTSP, 802.1X, TCP/IP and UDP/IP.
H.264 and MJPEG compression – The camera can generate multiple
H.264 and MJPEG streams simultaneously, individually configurable
with streams up to 30 frames per second (fps) or fixed at 9 fps for export
simplification.
Multicast and user definable ports – Supports multicast IP address and
user definable ports for both H264 and MJPEG streams.
Web-based management – Administration and management of the IP
camera can be performed through the Ganz Thermal web-based
configuration menus.
Motion detection – The IP camera can detect motion based on region of
interest definitions and can generate events/alerts if motion is detected.
Network Time Protocol (NTP) – Allows the IP camera to synchronize its
internal clock with a local or Internet time server.
Pan/Tilt and eZoom — The IP camera supports motorized pan & tilt and
digital zoom (4X).
Camera access control — You can control access to IP camera
configuration menus and live video by configuring various user types
and log in credentials.
Analog video output (NSTC/PAL) via BNC connection.
Ganz Thermal Series User Manual
4
2.2 CAMERA HARDWARE
Physical details of the IP Camera are provided below.
Figure 1: Ganz Thermal® ZNT6-P Camera
Figure 2: Ganz Thermal® ZNT6-P Camera Mount
Ganz Thermal Series User Manual
5
Item
Description
Function
1
Factory Reset Button
Reset button reboots the IP camera and resets it to the
factory default state. You can use a pin or paper clip to
depress it and hold for at least 6 seconds.
2
4-Pin AC/DC Power Connection
4-pin terminal block for power input – 2 for AC power input, 1
for DC power input and 1 for Ground.
12-24V DC or 24V AC power with minimum 13W or 0.54A
and 10% tolerance.
3
Analog Video Out
Accepts a standard BNC terminated coax cable for analog
video output.
4
Ethernet Connection
Indicates information about the network connections as
follows:
Off – LAN connection is NOT detected
Solid Green - 100 MB LAN connection is detected
Solid Amber - 10 MB LAN connection is detected
Flashing Green/Amber - Data is being transmitted or received
via the LAN connection
5
RS-485 Connection
Accepts wiring connections for a Pelco-D compatible joystick.
Figure 3: Ganz Thermal® ZNT6-P Series Bottom View
Table 1: Ganz Thermal® ZNT6-P Series Connections
Ganz Thermal Series User Manual
6
Focal Plane Array
Sensor Type
Uncooled VOx Microbolometer
Array Format
320x240 (ZNT6-Pxx1 Series)
640x480 (ZNT6-Pxx2 Series)
Pixel Pitch
17 µm
Spectral Band
8 - 14 µm (LWIR)
Sensitivity (NEDT) @ f/1.0
< 50 mK at f/1.0
Video
Frame Rate
Configurable for up to 30 Frames Per Second (fps) or
Fixed at 9 fps
Format
Analog: NTSC/PAL
IP: H264/MJPEG
Gain/Level Control
Automatic
4X Digital Zoom
1X-4X; 0.25X increments
Image Display
White Hot, Black Hot, Invert/Revert
Symbology
On screen display with date, time, and user defined text
Zoom
4x Digital Zoom with ePan/eTilt
Image Processing
Image Contrast Enhancement (ICE™) for superior
performance
Communication Interface
Protocols
IP: ONVIF™ Conformant (v 2.0 / Profile S), RTP, RTSP,
TCP, UDP, DHCP, FTP, HTTP, and NTP
Analog: PELCO-D
Interfaces
IP: Ethernet (10/100 Base T), RJ-45
Analog: RS-485
Security
802.1X Network Access Control and HTTPS
Electrical
Voltage
12-24 V DC, 24V AC, 802.3af Power Over Ethernet (PoE)
Power
<12.95 W with Heater
Environmental
Operating Temperature
-20°C to +60°C (-40°F to 140°F)
Storage Temperature
-50°C to +75°C (-58°F to +167°F)
3 SP E C I FI C A T I ONS
3.1 QUICK REFERENCE SPECIFICATIONS
The Ganz Thermal® Series Specifications are detailed below in Table 2.
Table 2: Ganz Thermal® Series Specification Quick Reference Table
Ganz Thermal Series User Manual
7
Mechanical
Dimensions (Diameter x Height)
20 x 27 cm
Volume
8000 cm
3
Weight
< 3 kg
Enclosure
IP66 (Ball-down), Tamper Resistant
Motion Mechanics
Pan Range (Azimuth): Continuous 360°
Tilt Range (Elevation): ± 120°
Pan-and-Tilt Speed: 30° per second
Pan-and-Tilt Accuracy: ± 2.5°
Optics
Athermalized Fixed Focus Lens for ZNT6-Pxx1
Horizontal Field of View (HFOV)
90°
40°
24°
16°
9°
f/no
1.4
1.2
1.0
1.1
1.2
Effective Focal Length
3.8mm
7.5mm
13mm
19mm
35mm
Athermalized Fixed Focus Lens for ZNT6-Pxx2
Horizontal Field of View (HFOV)
90°
44°
37.5°
24.8°
17.6°
f/no
1.4
1.2
1.2
1.2
1.2
Effective Focal Length
7.5mm
14.25mm
16.7mm
25mm
35mm
Software
Ganz Thermal Web Interface
Administrator, Operator, and Viewer with Password
Protection
Hardware
Embedded Memory
2 GB for Video Storage and Image Capture
Approvals
Environmental/Enclosure
IEC 60529 IP66
Emissions
FCC Part 15 Subpart B Class A, CISPR22 Class B,
EN55022 Class A
Electrostatic Discharge (ESD)
EN 61000-4-2 as modified by EN 55024
Electrical Fast Transients (EFT)
EN 61000-4-4 as modified by EN 55024
Radiated Disturbances
EN 61000-4-3 as modified by EN 55024
Conducted Disturbances
EN 61000-4-6 as modified by EN 55024
Power-Frequency Magnetic Fields
EN 61000-4-8 as modified by EN 55024
RoHS
European RoHS directive, 2011/65/EU
Safety
UL 60065 7th Edition 2007-12-11, CAN/CSA-C22.2
No.60065-03, 1st Edition, 2006-04+A1:2006
Loading...