GAI-Tronics 354-001OR User Manual
Pub. 42004-489D
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
Model 354-001 Series
NEMA 4X Industrial Telephone
Confidential ity Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
General Information
GAI-Tronics Model 354-001 series NEMA 4X
Industrial Telephones are designed for use in extreme
weather conditions where temperature and moisture
are a concern. They are also ideal for use in areas
that require a direct water spray (hose-down) for
cleaning purposes or where a non-corrosive material
is required.
The 354-001 series Telephone is perfectly suited for
areas considered too harsh for a standard telephone.
The 354-001 series Telephone operates in the same
manner as a standard telephone – simply lift the
handset, listen for a dial tone, and dial the desired
telephone number. The telephone is completely linepowered.
Fea tures
Features include:
NEMA 4X rated with door closed (NEMA 3R with door open)
Line-powered operation
®
Handset with 6-foot Hytrel
Panel-mounted push-button volume control
Chrome-plated keypad with protective rubber boot and Braille reference
Brushed stainless steel panel
coiled cord and noise-cancelling microphone
Figure 1. Model 354-001 Series NEMA 4X
Industrial Telephone
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
V
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
Pub. 42004-489D
Model 354-001 Series NEMA 4X Industrial Telephone Page 2 of 10
Ordering Information
The Model 354-001 series NEMA 4X Industrial Telephone is available in three standard models:
Table 1. Model Chart
Model Description
354-001 NEMA 4X Industrial Telephone, Gray
354-001YL NEMA 4X Industrial Telephone, Yellow
354-001OR NEMA 4X Industrial Telephone, Orange
354-001RD NEMA 4X Industrial Telephone, Red
The following options are available:
Key-lock front door
Coiled cord (15-foot)
Armored handset cord (15-inch)
Spring door closure
The following kits are available:
Model 12565-009 Ring Detector Relay Kit (output contact rated 5 A @ 30 V dc/ac)
Model 12576-130 Front Panel Replacement Kit
Installation Guidelines
ATTENTION
accordance with the National Electrical Code or applicable local codes.
Safety Guidelines
When installing any GAI-Tronics telephone equipment, please adhere to the following guidelines to
ensure the safety of all personnel:
NEVER install telephone wiring during a lightning storm.
Installation should be performed by qualified personnel and only in
Install a UL Listed lightning arrestor on any telephone installed where the telephone or telephone
cable is at risk of being exposed to lightning strikes. The lightning arrestor must be installed as close
as possible to maximize the protection. It must not be installed within the enclosure supplied with the
telephone. Please consult our Service Center at 800-492-1212 for further information.
Do not install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
Do not touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
f:\standard ioms - current release\42004 instr. man uals\42004-489d.doc
01/15
Pub. 42004-489D
Model 354-001 Series NEMA 4X Industrial Telephone Page 3 of 10
Installation
WARNING
station and any associated equipment before beginning any installation.
CAUTION
approval listing in the “Specifications” section of this manual . Such installa tion may cause a safety
hazard and consequent injury or property damage.
Install equipment without modification and according to all applicable local and national electrical codes.
Consult the National Electrical Code (NFPA 70), Canadian Standards Association (CSA 22.1), and local
codes for specific requirements regarding your installation. Class 2 circuit wiring must be performed in
accordance with NEC 725.55.
This product can contain hazardous voltages. Always remove power to this
Do not install this equipment in areas other than those indicated on the
Security Hardware
The Model 354-001 series Telephone is vandal-resistant, with the front panel attached to its enclosure
with security screws. A GAI-Tronics Model 233-001 Security Screwdriver (sold separately) or Torx T25 security head tip (included with the telephone) is recommended for installing the security screws.
Conduit Installa tion Details
GAI-Tronics recommends installing telephone cable in conduit to protect against damage and vandalism.
Mounting and wiring of the Model 354-001 series Telephones must be in accordance with installation
standard practices.
Entering the enclosure from the top is not recommended. Bottom (preferred) or side entry helps prevent
condensation moisture from dripping onto the telephone electronics causing severe damage. If using
conduit, an appropriate hub (Myers STG series recommended) or a UL Listed NEMA 4X rated connector
appropriate for the installation should be used. If a top entry must be made, a drip path is strongly
recommended. Seal all conduit entrances around the entry point and inside the conduit using a siliconetype sealant.
The Model 354-001 series Telephones are not supplied with openings for conduit or cable because of
potential installation variations. Conduit entrances must be installed prior to mounting the enclosure to
the wall surface.
1. Open the door and remove the front panel assembly (carefully set aside).
2. Drill (hole saw) or punch entry openings using the template provided with the telephone. There must
be a minimum of 1 inch (26 mm) of material between entry holes.
3. Install hub or fitting.
f:\standard ioms - current release\42004 instr. man uals\42004-489d.doc
01/15
Pub. 42004-489D
Model 354-001 Series NEMA 4X Industrial Telephone Page 4 of 10
Mounting the Enclosure
Mount the enclosure using the four 0.437-inch (11mm) diameter holes located on the mounting flanges
with 3/8-inch (M8) hardware. For specific details, including mounting hole dimensions and spacing, refer
to Figure 2.
Figure 2. Mounting and Entry Locations
f:\standard ioms - current release\42004 instr. man uals\42004-489d.doc
01/15
Loading...