GAI-Tronics 13380-001, 13380-004, 13380-002, 13380-003 Instruction And Service Manual

G AI - TRO NI CS®

A HUBBELL CO MPANY

Model 13380-xxx Series

Loudspeakers

Instruction and Service Manual

This manual covers the following loudspeaker models:

•

Model 13380-001, 8-ohm, 15 watts, 10.95 volts

Pub. 42004-394C

•

Model 13380-002, 16-ohm, 15 watts, 15.49 volts

•

Model 13380-003, 70 V line, 15 watts, 70 volts

•

Model 13380-004, 100 V line, 15 watts, 100 volts

GAI-TRONICS 3030 KUTZTOWN RD. READING, PA 19605 USA

610-777-1374  800-492-1212  Fax: [phone]

VISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS

INSTRUCTION & SERVICE MANUAL

• 15 Watt Loudspeaker

Max. Operating Temperature / Code at +55ºC Ambient

Hazardous Location

Temperature Code

Class I, Division 2, Groups A, B, C, D

T4 (135ºC)

Class II, Division 2, Groups F and G

T6 (85ºC)

Class III, Divisions 1 and 2

T6 (85ºC)

Max. Operating Temperature / Code at +40ºC Ambient

Hazardous Location

Temperature Code

Class I, Division 2, Groups A, B, C, D

T4A (120ºC)

Flat Washer

Spring Washer

M4 Hex
Socket Screw

18° Increments

Release nut to rotate
bracket.

• 70V or 100V Line Transformer
with 15W, 7.5W, 3W and 1W tapings

• 8 ohm or 16 ohm

• Type 4 / 4X / 13

• Operating Temperature Range

−20ºC to +55ºC

Unit Type No. 13380-XXX

Impedance: 8 ohm or 16 ohm

70V Line or 100V Line

13380-XXX 15W LOUDSPEAKERS

For Use In Hazardous Locations

MOUNTING
The 13380 15W loudspeaker must be mounted using the

rotating bracket as shown.

7KA1

WARNING – EXPLOSION HAZARD - SUBSTITUTION OF

COMPONENTS MAY IMPAIR SUITABILITY
FOR CLASS I, II DIVISION 2.

The equipment is suitable for use in the hazardous locations
listed above or non-haz ardou s locatio ns only

ARNING – DO NOT OPEN WHEN ENERGISED

W

CAUTI0N – DO NOT OPEN WHEN AN EXPLOSIVE GAS

.

OR DUST ATMOSPHERE IS PRESENT

WIRING INSTALLATION

The 13380 15W loudspeaker is provided with 1 M20 x 1.5 cable
entry and one ½” NPT cable entry. The M20 entry is provided
with a stopping plug in place.

Installation using Cable Glands without Field Wiring Leads

The cable connections are made into the terminal blocks on the
electronic PCB assembly. Terminal blocks are suitable for field
wiring (AWG 18-12). Strain relief has to be ensured by
installation with a suitable cable gland. Follow the markings for
the terminals on the PCB and install wiring as shown in the
diagram below.

Cable glands need to be UL certified to ANSI/UL 2225 or C22.2
NO. 174-M1984, and to UL514B / CSA-C22.2 No. 18.3-12,
ratings for hazardous locations must be equal to or better than
the rating of the sounder used.
If a high IP (Ingress Protection) rating is required then a
suitable sealing washer must be fitted under the cable gland.

__________________________________________________________________________________________________________________
GAI-Tronics 3030 Kutztown Rd. Reading PA 19605 USA

ument No. IS4211-GAI-TRON Issue: A 24-06-14

Doc

[e-mail] Tel: [phone]
www.gai-tronics.com Fax: [phone]

Sheet

3 of 4