GAI-Tronics 12761-002 User Manual
Pub. 42003-074
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
Handset Cradle/Sensor Assembly
Replacement Kit
Model 12761-002
Confidentiality Notice
This manua l is provide d sole ly as an operatio nal, installation, and ma inte nance guide and conta ins
sensitive business and t e chnical informatio n tha t is confidentia l and pr opri et ary to GAI- Tronics.
GAI-Tronics retains all intellectual property and other rights in or to the information contained herein,
and such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manu al may not be dis clos e d in any form, in whole or in pa rt, direct ly or i ndir ectly, to a ny
third pa r ty.
General Information
This kit is for use on the following models: Model 9101, 9101A, 9105, 9105A, 9201, 9201A, 9205, and
9205A.
Installation
Models 9101, 9101A, 9105, and 9105A
Removing th e Old Assem bly
1. Remove the two mounting screws from the mounting bracket. Remove the subset from the mounting
bracket.
2. Remove the six screws holding the unit together.
3. Lay the unit open to access the PCBA.
4. Note the location of and remove the two reed switch wires from the PCBA.
5. Use a Phillips screwdriver to remove the two screws securing the handset cradle to the front panel.
Set the screws aside.
6. Pull the old cradle assembly through the front panel, and discard it.
GAI-Tronics Corporation P.O. Box 1060, Readi ng, PA 19607-1060 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
V
Pub. 42003-074
M
ODEL 12761-002 HANDSET CRADLE/SENSOR ASSEMBLY REPLACEMENT KIT Page: 2 of 2
Installing the New As sembly
1. Feed the two wires through the opening in the front panel.
2. Use the new screws to secure the new handset cradle. The wider end of the cradle must be towards
the top of the unit to allow the handset to fit in the cradle.
3. Connect the two wires from the assembly to the PCBA at the same location as the old switch.
4. Replace the six screws to reassemble the unit.
5. Use the two mounting screws to secure the subset to the mounting bracket.
Models 9201, 9201A, 9205, and 9205A
Removing th e Old Assem bly
1. Remove the unit from the wall or mounting surface.
2. Remove the four back panel screws.
3. Lay the unit open to access the PCBA.
4. Note the location of and remove the two reed switch wires from the PCBA.
5. Remove the four screws holding the top half of the printed circuit board, and unfold it.
6. Remove the standoffs holding the lower half of the board, and move the board aside.
7. Use a Phillips screwdriver to remove the two screws securing the handset cradle to the front panel.
Set the screws aside.
8. Pull the old cradle assembly through the front panel, and discard it.
Installing the New As sembly
1. Feed the two wires through the opening in the front panel.
2. Use the new screws to secure the handset cradle. The wider end of the cradle must be towards the top
of the unit to allow the handset to fit in the cradle.
3. Reinstall the low er half of the P CBA with the standoff s.
4. Fold the t op half of th e board over , and secure it w i th the scr e ws.
5. Connect the two wires from the assembly to the PCBA at the same locations as the old switch.
6. Attach the back panel with the four screws.
7. Remount the unit.
\\s_eng\gtc proddoc s \st andard iom s - current release\42003 kit manuals \ 42003-074. doc
1991
Loading...