Page 1
Pub. 42003-233B
GAI-TRONICS® CORPORATION
A HUBBELL COMPANY
ICS Subset to ICS Page/Party® Amplifier
15-Foot Cable Assembly
MODEL 12587-104
Confidentiality Notice
This manual is provided solely as an operational, installation, and maintenance guide and contains
sensitive business and technical information that is confidential and proprietary to GAI-Tronics. GAITronics retains all intellectual property and other rights in or to the information contained herein, and
such information may only be used in connection with the operation of your GAI-Tronics product or
system. This manual may not be disclosed in any form, in whole or in part, directly or indirectly, to any
third party.
General Information
The Model 12587-104 ICS Subset to ICS Page/Party® Amplifier Cable Assembly makes it possible to
connect an ICS Page/Party
through conduit or a narrow wall cavity when being routed.
®
remote subset to an ICS remote amplifier when the cable assembly must fit
The Model 12587-104 Cable Assembly consists of a 15-foot, 24-conductor, PVC jack cable with a DB25
connector on one end and stripped and tinned wires on the other end. This allows the attachment of an
additional DB25 connector after the wire is installed into a receptacle box.
Installation to a W all Receptacle
1. Arrange the cable so that connector P1 is located at the ICS amplifier enclosure. Plug the DB25
connector into the bottom of the amplifier enclosure and secure the thumb screws from the male
DB25 connector.
Figure 1. Installation
GAI-Tronics Corporation 400 E. Wyomissing Ave. Mohnton, PA 19540 USA
610-777-1374 800-492-1212 Fax: 610-796-5954
ISIT WWW.GAI-TRONICS.COM FOR PRODUCT LITERATURE AND MANUALS
V
Page 2
Pub. 42003-233B
M
ODEL 12587-104 ICS SUBSET TO ICS PAGE/PARTY® AMPLIFIER 15-FOOT CABLE ASSEMBLY Page: 2 of 2
2. Route the 15-foot cable assembly through the wall or conduit from the ICS amplifier enclosure to the
subset location or wall receptacle.
3. Install the supplied spare DB25 connector onto the stripped and tinned wires side of the cable
assembly. Place the stripped wire ends into the solder cups in a manner that allows the exposed wire
to bottom out against the base of the solder cup. Solder all wires from the cable to the DB25
connector. See Figure 2 for wire color terminations.
4. Arrange the cable so that the soldered DB25 connector plugs into the subset or ICS subset extension
cable. Plug the DB25 connector into the rear of the ICS subset or extension cable and secure the
thumb screws from the female DB25 connector.
Figure 2. Wire Color Terminations
f:\standard ioms - current release\42003 kit manual s\42003-233b.doc
03/11
Page 3
Warranty
Equipment. GAI-Tronics warrants for a period of one (1) year from the date of shipment, that any
GAI-Tronics equipment supplied hereunder shall be free of defects in material and workmanship, shall
comply with the then-current product specifications and product literature, and if applicable, shall be fit
for the purpose specified in the agreed-upon quotation or proposal document. If (a) Seller’s goods prove
to be defective in workmanship and/or material under normal and proper usage, or unfit for the purpose
specified and agreed upon, and (b) Buyer’s claim is made within the warranty period set forth above,
Buyer may return such goods to GAI-Tronics’ nearest depot repair facility, freight prepaid, at which time
they will be repaired or replaced, at Seller’s option, without charge to Buyer. Repair or replacement shall
be Buyer’s sole and exclusive remedy. The warranty period on any repaired or replacement equipment
shall be the greater of the ninety (90) day repair warranty or one (1) year from the date the original
equipment was shipped. In no event shall GAI-Tronics warranty obligations with respect to equipment
exceed 100% of the total cost of the equipment supplied hereunder. Buyer may also be entitled to the
manufacturer’s warranty on any third-party goods supplied by GAI-Tronics hereunder. The applicability
of any such third-party warranty will be determined by GAI-Tronics.
Services. Any services GAI-Tronics provides hereunder, whether directly or through subcontractors,
shall be performed in accordance with the standard of care with which such services are normally
provided in the industry. If the services fail to meet the applicable industry standard, GAI-Tronics will
re-perform such services at no cost to buyer to correct said deficiency to Company's satisfaction provided
any and all issues are identified prior to the demobilization of the Contractor’s personnel from the work
site. Re-performance of services shall be Buyer’s sole and exclusive remedy, and in no event shall GAITronics warranty obligations with respect to services exceed 100% of the total cost of the services
provided hereunder.
Warranty Periods. Every claim by Buyer alleging a defect in the goods and/or services provided
hereunder shall be deemed waived unless such claim is made in writing within the applicable warranty
periods as set forth above. Provided, however, that if the defect complained of is latent and not
discoverable within the above warranty periods, every claim arising on account of such latent defect shall
be deemed waived unless it is made in writing within a reasonable time after such latent defect is or
should have been discovered by Buyer.
Limitations / Exclusions. The warranties herein shall not apply to, and GAI-Tronics shall not be
responsible for, any damage to the goods or failure of the services supplied hereunder, to the extent
caused by Buyer’s neglect, failure to follow operational and maintenance procedures provided with the
equipment, or the use of technicians not specifically authorized by GAI-Tronics to maintain or service the
equipment. THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE IN LIEU OF AND
EXCLUDE ALL OTHER WARRANTIES AND REMEDIES, WHETHER EXPRESS OR IMPLIED BY
OPERATION OF LAW OR OTHERWISE, INCLUDING ANY WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Return Policy
If the equipment requires service, contact your Regional Service Center for a return authorization number
(RA#). Equipment should be shipped prepaid to GAI-Tronics with a return authorization number and a
purchase order number. If the equipment is under warranty, repairs or a replacement will be made in
accordance with the warranty policy set forth above. Please include a written explanation of all defects to
assist our technicians in their troubleshooting efforts.
Call 800-492-1212 (inside the USA) or 610-777-1374 (outside the USA) for help identifying the
Regional Service Center closest to you.
(Rev. 10/06)
Loading...