Page 1
Type Sup 037RG
Errata: Descaling
These instructions replace those reported in the manual.
Page 2
• 6 •• 6 •
Steady on
DESCALING
Limescale normally builds up with the use
of the appliance.
The machine must be descaled when the
icon appears on the display.
Do not turn the machine o
or put it in stand-by mode
during the descaling process.
Use the GAGGIA descaling
solution only. Its formula
has been designed to ensure better
performance and operation for the
machine's entire working life. A correct use of the solution also avoids
alterations in the brewed product.
Warning! Never drink the
descaling solution or any
products dispensed until the cycle
is complete. Never use vinegar as a
descaling solution.
Before descaling the machine, perform
the following operations:
- remove the Pannarello (if supplied)
from the steam wand as described
in the "Cleaning and Maintenance"
chapter;
- empty the drip tray. Place it back in the
machine before proceeding.
1 Place a large container under the
dispensing spout.
Turn the machine o by pressing the
"STAND-BY" button. Wait for the
machine to complete the rinse
process.
Warning! Remove the "Intenza" lter before adding the
descaling solution.
Note: should the containers
ll up, temporarily suspend
the dispensing process in order to
empty the containers.
If descaling solution and/or water
spills out of the dispensing spout:
PAUSE: turn the selector switch to the
"
" position;
START: turn the selector switch to the
"
" position.
If descaling solution and/or water
spills out of the steam wand:
PAUSE: turn the selector switch to the
"
" position;
START: turn the selector switch to the
"
" position.
• Pour the entire content of the GAGGIA
concentrated descaling solution into
the water tank and fill it with fresh
drinking water up to the MAX level.
Place the tank back into the machine.
3 Make sure the selector switch is in the
“
” position.
4 Press and hold the 2 brew buttons at the
same time for 3 seconds: the descaling
cycle is started.
Page 3
• 7 •
English
Note: if the “ ” and “ ”
indicator lights start blinking immediately after start-up, turn
the selector switch right to the “
”
position. When the “
”, “ ” and
“
” indicator lights start blinking,
turn the selector switch back to the
“
” central position.
5 The " " light blinks quickly to show
the machine has entered the descaling
automatic programme; when the "
" light is steady, the 1
st
limescale
removal phase is on.
6 Place an empty container under the
steam wand and another one under
the dispensing spout.
7 When the “ ” and “ ” lights start
blinking, turn the selector switch
clockwise to the “
” position; in this
case, the steam/hot water wand starts
dispensing the descaling solution at
regular intervals.
8 When there is no more descaling solu-
tion left in the water tank, the “
” ,
“
” and “ ” lights blink simul-
taneously.
9 Turn the selector switch to the “ ”
central position.
Empty the container under the steam
wand and the one under the dispensing
spout.
11 Remove the water tank, rinse it and
ll it up to the “MAX” level with fresh
drinking water.
10 The
“ ” light turns on and the water
tank must be removed before entering
the next stage.
12 Place the tank back in the machine. The
two
“ ”
lights turn on showing the
machine has entered the rinse phase.
The “
” and “ ” lights are blinking
in the display.
13 Place an empty container under the
steam wand and another one under
the dispensing spout.
Turn the selector clockwise to the “ ”
position.
14 When the “ ” , “ ” and “ ” lights
start blinking at the same time,
turn
the selector switch to the “
” central
position.
The machine starts rinsing directly from
the dispensing spout.
Page 4
• 8 •• 8 •
15 When the “ ” and “ ” lights start
blinking, turn the selector switch clockwise to the “
” position; in this case,
the steam/hot water wand dispenses
the rinsing water continuously.
16 When there is no more rinsing water
left in the water tank, the “
” , “ ”
and “
” lights blink simultaneously.
17 Turn the selector switch to the “ ”
central position.
18 The
“ ” light turns on and the water
tank must be removed before entering
the next stage.
Empty the container under the steam
wand and the one under the dispensing
spout.
19 Remove the water tank, rinse it and
ll it up to the “MAX” level with fresh
drinking water.
20 Place an empty container under the
steam wand and another one under
the dispensing spout.
21 When the “
” and “ ” lights start
blinking, turn the selector switch
clockwise to the “
” position. The
second rinse cycle is started.
If the tank is not lled up to
the MAX level, the cycle must
be repeated from point 16.
22 When the second rinse cycle is over,
the machine enters the stand-by mode
and the “
” button starts blinking.
Empty the container under the steam
wand.
23 Turn the selector switch to the
“ ”
central position.
Page 5
• 9 •
English
24 At the end, re ll the water tank.
Reassemble the external part of the Pannarello.
The descaling cycle is complete.
Start the machine as described in the
manual and perform normal warm-up
and rinse operations: the machine is now
ready for product brewing.
If the machine is switched o
during the descaling cycle,
next time the machine is switched
on the cycle must be repeated from
the point it has been paused.
The descaling solution is to
be disposed of according
to the manufacturer’s instructions
and/or the regulations in force in the
country of use.
After completing the des-
caling cycle, wash the brew
group as described in the "Brew
Group" section in the "Cleaning and
Maintenance" chapter.
Remarks on descaling
The previous section explains the correct
operations to perform to descale the
machine.
The machine you have purchased is
equipped with advanced software to
check the quantity of used water in order
to provide reliable information about the
right time to carry out descaling operations.
This software has been programmed for
standard water hardness.
In case of especially hard water (high
calcium content), descaling cycles might
have to be carried out more frequently,
even if the machine does not display
warning signals.
Even if the machine is not used often (e.g.
1 coffee per day), it is recommended to
perform descaling cycles more frequently.
In these specific cases, it is recommended
to perform descaling cycles every 1-2
months, even if the machine does not
signal it.
Page 6
Page 7
GAGGIA s.p.a.
Sede Legale/Registered Office
Piazza Eleonora Duse, 2
20122 MILANO
Sede Amministrativa/Administrative Office
Via Torretta, 240
40041 Gaggio Montano (BO)
+39 0534 77111 www.gaggia.com
www.gaggia.com
Il produttore si riserva il diritto d`apportare qualsiasi modi ca senza preavviso.
The manufacturer reserves the right to make changes without prior notice.
Der Hersteller behält sich das Recht vor, Änderungen jeder Art ohne Vorankündigung vorzunehmen.
Le producteur se réserve le droit d’apporter des modi cations sans aucun préavis.
El fabricante se reserva el derecho de modi car el producto sin aviso previo.
O fabricante reserva-se o direito de efectuar qualquer alteração sem aviso prévio.
De fabrikant behoudt zich het recht voor zonder voorafgaande berichtgeving wijzigingen aan te brengen.
Producent zastrzega sobie prawo do wprowadzenia zmian w produkcie bez wcześniejszej zapowiedzi.
© Gaggia S.p.A .
Cod.15003932 Rev.01 del 20-09-12
Loading...