VR 414 611
Stainless steel
Width 15" (38 cm)
Included accessories
1 cast-iron griddle, half size
1 grease collecting insert
2 cast-iron grills
1 lava stone
1 cleaning brush
Installation accessories
In combination of several Vario
cooktops or VL 414 downdraft,
connecting strips must be used.
Choose respective VA 420 strip from
one of the below, depending on type
of installation.
VA 420 000
Connection strip for combination
with other Vario 400 series appliances
for flush mounting.
VA 420 010
Connection strip for combination
with other Vario 400 series appliances
for surface mounting.
VA 440 010
Stainless steel appliance cover with
mounting strip.
Only available for individual Vario
installation.
Optional accessories
LV 030 000
Lava stones for refilling.
Combinable with:
2x VL414712
AL400721
AI442720 / AI442760
AW442720 / AW442760
AF210791
Good to know:
Wall installations require the hood to
be as large as the cooktop(s). Island
installations require the hood to be
larger than the cooktop(s).
Important note:
If paired with VL414712, for best
performance it's recommended to place
a VL on each side of the electric grill.
Vario 400 series electric grill
VR 414
– Two zones can be operated
together or separately
– Half size cast-iron griddle included
for simultaneous searign and
grilling on two seperate surfaces
– Open cast-iron grill, lava stones
– Solid stainless steel control knobs
– Precision crafted ⅛" stainless steel
frame
– For surface-mount installation with
a visible edge or for flush
installation
– Can be perfectly combined with
other Vario 400 series appliances
– Not recommended for recirculating
ventilation
Operation
Control knobs with illuminated ring,
cooking zone and output level
markings.
Electronic control in 12 output levels.
Features
Cooktop, lava stone trough and grease
collecting insert from stainless steel.
Two zones, each 1500 W, can be
operated together as a complete
surface or each halve separately.
Two-part cast grill.
Safety
Safety shut-off.
Pre-heat and residual heat indicator.
Planning notes
If using the VL414 downdraft for
ventilation, the Vario electric grill must
be placed between two VL downdrafts.
Recirculation is not recommended.
Depending on the type of installation
(surface-mounted or flush-mounted,
with or without an appliance cover),
the specific location of the cut-out and
the knob positions may vary.
If installing with the appliance cover
VA 440 take into account the
additional
space required for the depth.
If combining several Vario 400 series
appliances, a connection strip
VA 420 must be placed between the
appliances. Depending on the type of
installation, the corresponding
connection strip must be provided.
The bearing capacity and stability, in
the case of thin countertops in
particular, must be supported using
suitable substructures. Take into
account the appliance weight and
additional loads.
Additional instructions for flush
mounting:
Installation is possible in countertops
made of stone, synthetics or solid
wood.
Heat resistant and watertight sealing
of the cut edges must be observed.
For a suitable heat resistant filler
please consult the countertop
manufacturer.
The groove must be continuous and
even, so that uniform placing of the
appliance on the gasket is ensured.
Do not use discontinuous lining.
The joint width may vary due to size
tolerances of the combinations and of
the countertop cut-out.
If installing several appliances in
individual cut-outs, allow for a
minimum distance of 1 ¹⁵/₁₆" (50 mm)
between the cooktops.
A minimum lateral clearance of at least
4" from adjacent heat-sensitive
cabinets or from the wall must be
observed.
Recirculation is not recommended for
the electric grill.
It is recommended that the electric
grill is installed, if possible, in the
center of the cooktop configuration
and not at the edge.
Appliance can be snapped into the
countertop from above.
Appliance weight: approx. 57.3 lbs.
Rating
Rating: 3,000 W
Minimum fuse protection: 16 A
Electrical: 208 / 220–240 V / 60 Hz
Electrical connection:
Hardwire required, 59" cable length.
www.gaggenau.com/us
Revised: June 2021
Surface-mount Installation Flush-mount Installation
Installation of the control knob; surface mounting
Longitudinal section
(B)
14¹⁵⁄
"
(384+1)
Cross-section
20½"
14¹⁵⁄
16
⅛" (3)
4½" (115) (B)
16
59¹⁄
(1500)
≥ 1¹⁵⁄
16
"
(50)
> 1⅜"
"
(35)
14¹⁵⁄
(380)
16
"
20½"
16
3⁹⁄
14³⁄
(360 )
(520) (A)
" (90)
±¹⁄
"
16
±1
"
16
±¹⁄
19⅜"
±1
(492 ) (A)
ø 1¹⁵⁄
16
"
(50)
ø 2⅜"
16
(60)
"
R ⅛" (R 3)
90°
4⅝" (118) (B)
59¹⁄16"
(1500)
≥ 1¹⁵⁄
16
"
(50)
> 1⅜"
(35)
(380)
"
16
3⁹⁄
(90)
14³⁄16"
(360 )
15⅛"
(384+1)
20½"
(520) (A)
"
16
"
±¹⁄
±1
+¹⁄16"
⅛" (3)
±¹⁄
19⅜"
±1
(492 ) (A)
16
ø 1¹⁵⁄
(50)
ø 2⅜"
16
"
(60)
"
+¹⁄16"
20⅝"
(524+1) (A)
R ³⁄
+¹⁄16"
16
"
(R 4+1)
(C)
90°
R ⅛" (R 3)
Installation of the control knob
> 1⅜" (35) > 1⅜" (35)
1⅜" (35)
16
" (50) ø 1¹⁵⁄16" (50)
ø 1¹⁵⁄
≤ ⅞" (23)
2¾" (70)
> ⅞" (23)
⅞" (23)
Longitudinal section
¹⁄16"
(2)
(380)
14³⁄
(360 )
15⅛"
16
Cross-section
16
"
¹⁄
(2)
(520)
19⅜"
(492 )
20⅝"
(524+1)
"
16
±¹⁄
±1
+¹⁄16"
±¹⁄
±1
+¹⁄16"
¹⁄16"
(2)
(A)
16
"
(B)
¹⁄16"
(2)
(A)
16
"
Numbers indicated
inside parenthesis ( ) = mm
www.gaggenau.com/us
Revised: June 2021
Loading...