en
Installation instructions
Outer wall fan
fr
Notice de montage
Ventilateur sur mur extérieur
es
Instrucciones de montaje
Soplador para paredes externas
2
Important information
This appliance conforms to the relevant
safety regulations.
Repairs should only be carried out by
qualified specialists.
Improperly executed repairs can give
rise to significant hazards for the user.
몇 Note down the type designation of the
external fan in the extractor hood operating
instructions.
몇 The appliance should only be
connected up to the mains and taken into
use by a qualified specialist.
몇 Before carrying out repairs or
maintenance, isolate the fan.
To do this, disconnect the plug-and-socket
connection of the electric cable which is
connected to the extractor hood or
disconnect the extractor hood power cord
from the power supply.
몇If the connecting cable for this
appliance is damaged, the cable must be
replaced by the manufacturer or his
customer service or a similarly qualified
person in order to prevent serious injury to
the user.
몇 Old appliances are not worthless
rubbish. If they are disposed of in an
environment-friendly manner, valuable raw
materials can be recovered for use again.
Before you dispose of an old appliance,
make sure that it has been rendered
inoperative.
This appliance conforms to the relevant
safety regulations.
Repairs should only be carried out by
qualified specialists.
Improperly executed repairs can give
rise to significant hazards for the user.
몇 Your new appliance was protected on
its way to you by the packaging. None of
the materials cause pollution to the environment and all can be recycled for use again.
Please help to protect the
environment and dispose of the packaging
in an environment-friendly manner.
You can obtain information about the best
method disposing of old appliances and
packaging from your dealer or local
municipal council.
3
Prior to installation
Observe the official and statutory
regulations for the removal of exhaust
air (e.g. Landesbauordnungen).
D
If the extractor hood is operating in
exhaust-air mode at the same time as a
flue-type heater (e.g. gas, oil or solid-fuel
heater, instantaneous water heater, boiler),
there must be an adequate air supply
which the fireplace requires for combustion.
Safe operation is possible if the partial
vacuum in the installation room of the fireplace does not exceed 4 Pa (0.04 mbar).
This can be achieved if the combustion air
is able to flow through non-lockable openings, e.g. in doors, windows and in conjunction with an air supply/air-intake wall
box or by other technical procedures such
as reciprocal interlocking.
If the air supply is inadequate, there is a
risk of poisoning caused by combustion
gases being drawn back into the room.
Note: When assessing the air supply,
always take into account the entire ventilation system in the house. This rule does
not apply when using cooking appliances,
e.g. hob or gas cooker.
몇Do not attach the outer wall fan near
windows, doors or patios.
몇When attaching the outer wall fan,
ensure that
– residents and neighbours are not
disturbed by noise and odours,
– it is accessible for maintenance and
repairs.
몇The plug-and-socket connections of
the electric cables must be located inside
the building.
Preparing the wall
몇RISK OF INJURY,
DAMAGE TO PROPERTY
Before drilling the holes for the designated
installation location, check for concealed
electrical cables and other lines.
K The wall must be level and vertical.
K The enclosed screws and wall plugs are
suitable for solid brickwork. Use the
appropriate fixing materials for other wall
structures (e.g. plaster board, porous
concrete, poroton bricks).
Ensure that the wall has adequate load
bearing capacity.
K Ensure that the depth of the drilled holes
corresponds with the length of the screws.
K Ensure that the wall plugs are secure.
Weight: 7,0 kg.
We reserve the right to construction changes within the
context of technical development.
4
Installation
1. Wall opening
Diameter at least 8
17
/64”.
Distance to floor at least 39
1
/2” to ensure
an unobstructed air outlet.
2. Drill 4x
5
/16” ø holes for the mounting
plate and press in wall plugs flush with
the wall.
3. Drill
15
/32” ø hole for the electric cable.
몇The fan is connected to the extractor
hood with the Z 197” extension cable
enclosed with the extractor hood.
Ensure that the cables are fed through
properly.
4. Seal mounting plate and screw on tight.
몇 Risk of electric shock
The mounting plate must be sealed to
the outer wall with a suitable material to
prevent water from entering the
appliance.
Please follow application instructions
and observe use-by date for the enclosed silicone.
4x
A
B
5. Screw the fan onto the mounting plate.
(210mm)
Ø
(8mm)
1
/2”
949/64”
(248mm)
15
Ø
(12mm)
17
Ø8
/
64
5
/16”
4x
/32”
”
31
7
/64”
(190mm)
33
2
/64”
(64mm)
13/16”
(30mm)
47
3
/64”
(95mm)
min 39
(1.000mm)
4x
5
User information
Safety instructions
몇Regularly check that air can flow freely
out of the fan.
Do not obstruct the air outlet grille or cover
with plants.
몇If the connecting cable for this
appliance is damaged, the cable must be
replaced by the manufacturer or his
customer service or a similarly qualified person in order to prevent serious injury to the
user.
Cleaning and care
K Use a mild non-abrasive stainless steel
cleaner.
몇 Do not use any of the following to clean
stainless steel surfaces: abrasive sponges,
cleaning agents containing sand, soda, acid
or chloride!
K Apply a little stainless steel cleaner from
time to time in order to maintain the
appearance of the appliance.
6. Connect the pipe and cable from the fan
to the extractor hood.
몇 The additional cover on the plug
must always be attached and closed for
safety reasons.
Installation
Loading...