Futaba SBS-01RB User Manual

1M23N26727
Telemetry RPM Sensor
(Brushless type)
Instruction Manual
RPM
Brushless Motor
The RPM of a brushless motor can be viewed on your transmitter without removing the motor's magnet using only a wiring connection (soldering is nec­essary).
●The SBS-01RB can be used with Futaba telemetry transmit­ters and receivers and drive use brushless motors.
Thank you for purchasing Futaba's SBS-01RB brushless motor RPM sensor. By combining the SBS-01RB with a telemetry receiver, the RPM of a drive use brushless motor mounted in a model can be transmitted from the receiver to the transmitter. You can monitor the RPM of the model
during ight (running). Please read this
manual thoroughly to maximize your enjoyment and ensure proper sensing performance. We also encourage you to retain the manual for future reference.
Use : Brushless motor RPM Sensor Length : 475mm (18.7") Weight : 3.8g (0.134oz) Voltage : DC3.7 7.4V Range : 360 300,000RPM
LED Indication
Green Normal operation Red No signal reception
Green/Red
Green/Red Alternate blink
When setting up the slot
Unrecoverable error
WARNING
To utilize the SBS-01RB sensor, connect it to the S.BUS2 port of the
Futaba telemetry enabled receivers.
■ The SBS-01RB will not function properly
if co nnected t o an S.BUS port or other channel ports.
Do not use the SBS-01RB with anything other than an electric
R/C model.
Ensure that the unit is mounted in an area that will eliminate
exposure to fuel, water and vibration.
■ As w it h any ele ctr oni c c om ponen ts,
proper precautions are urged to prolong the life and increase the performance of the SBS-01RB.
To ensure that the SBS-01RB is functioning as desired, please test
accordingly.
■ Do not use until inspection is complete.
Allow a slight amount of slack in
the SBS-01RB cables and fasten them at a suitable location to prevent any damage from vibration.
Slot Number Setup
Please note that the proper default slot for this accessory is number two. Information on how to change the slot assignment is included in the transmitter's manual.
Wiring
Brushless motor
Of the 3 wires of the motor, any 2 are solder­connected. Any of the 3 wires can be used.
Number of poles of aircraft motor
Each aircraft use brushless motor has a different number of poles. The number of poles of the motor used must be checked against the motor instruction manual and entered at the telemetry RPM setup screen of the
transmitter. (Car use motors do not have to be set.) When the transmitter
does not have a number of poles input
item, input 1/2 the value of the number
of poles at the gear ratio.
©FUTABA CORPORATION 2014, 12 (1)
For a 14-pole motor → gear ratio 7.00
When you want to display the motor RPM of
*
a car use motor, set the gear ratio to 1.00
Helicopter rotor RPM
When you want to display the RPM of a helicopter rotor or of the propeller of an aircraft with its gear down instead of motor RPM, make the following settings.
For transmitter setting, select magnet type.
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
FUTABA CORPORATION
Motor controller
SBS-01RB
LED
1/2 number of poles × gear ratio = Input this value at the transmitter gear ratio.
(Example)
For 14 poles with a gear ratio of 6
7(1/2 number of poles)× 6 = 42
Input 42.00 at the gear ratio.
The upper limit of the gear ratio of the
*
T10J is 30.00. If this is insufcient, the gear ratio can be updated (maximum
99.99) by a Futaba Support Center.
Please inquire.
to S.BUS2 port
Loading...