Futaba FP4DN, FP5, FP5DN, FP6DN User Manual
New FUTABA
DIGITAL PROPORTIONAL
RADIO CONTROL
INDEX
Features........................................................................ 1
Specifications
Transmitter
Handling the
Ni-cads batteries &
Preca
tions,
Guarantee..................................................................
Factory repair service
............................................................
operation
Receiver
test & installation
................................................
& Servos
re-charging....................................
................................................
.................................
....................................
2
3
6
8
9
12
13
FUTABA NEW PROPORTIONAL R/C FEATURES
TRANSMITTER
1. All Futaba New Proportional Models are designed and manufactured to the identical standards and specifications.
Therefore mixing with other Futaba receivers and servos will not affect the operation.
2. Frequency changes are easily accomplished, because of the plug-in socket for the crystals.
3. Throttle control Lever location can be easily changed from
4. Neck strap and Hook is provided for convenient handling.
RECEIVER
1. Because of the New 8-BIT integrated circuit device,
are supplied with 6 channel capacity receiver FP-R6D.
2. Light weight and miniaturized by NEW 3-Wire Mini-Block connector.
3. Stable operation from 4V to 6.6V resulting from utilization of the power
4. Frequency change can be easily accomplished without opening the receiver case because of the unique outsidemounted crystal socket.
5. Strong rejection of spurious signals by utilization of a double tuned RF pre-selector circuit.
6. Shielded RF and Oscillator coils provide strong rejection of spurious signals.
7. Accidental touching of Futaba Transmitter and Futaba Receiver antennas will not affect the normal operation.
SERVO
1. Since the FP-S5, FP-S5L, FP-S4 are all designed and manufactured
their maximum capability even when mixed with other Futaba Models.
2. With the use of Monolithic intergrated circuit, Futaba BA-606 and BA-607 Servo AMPS are small in size,
light weight and sturdy with high output torque.
3. In the BA-607, the 12-pin single End-line Monolithic 1C contains a low current drain. High resolution. Temperature compensated Low-voltage circuit which allows operation down to 4V without creating interference
between adjacent Servos.
4. In the BA-606, the 9-pin single end-line integrated circuit is used. This circuit contains; 2 specially made high
out-put current (500mA) transistors of the PNP type, 2 NPN type transistors, 4 Diodes, 4 Resistors, a total of
12 integrated devices in a single package.
5. At idle, low current consumption. (8
6. High out-put (torque) 2 kg/cm.
mA).
left to right side.
used in all Futaba Receivers, all Futaba Propo. Systems
saving circuits.
to identical standards, they will display
1
TRANSMITTER OPERATION
With
the FP-4DN, a two-stick
operate:
1. Throttle
2. Aileron
3. Elevator
4. Rudder
With the FP-5DN, in addition to the above
mentioned operations, a snap-switch is
provided for the landing gear or other
suitable operations.
With the FP-6DN, aside from the 5 move-
ments above, an additional control (volume type control) is added on the front
panel for the 6th control (variable move-
ment).
Operating procedures for the FP-4DN, FP-
5DN, FP-6DN are the same as they are
designed and Manufactured to the same
specifications.
As an additional feature, all Futaba Propo.
Models are provided with two (2) sets of
knobs (long and short), to suit your requirements. To change knobs, pull firmly
off the Black Plastic Knobs from the control sticks and replace with the spare plastic knobs provided in the Kit.
A neck strap too is provided for your convenience.
control
will
3
The front panel controls on the Transmitters are shown in the Diagram below and it is suggested that the manipulation of these controls be well mastered.
4
FP-T4D
(for FP-4DN)
4-CHANNEL
FP-T5D
(for FP-5DN)
5-CHANNEL
FP-T6D
(for FP-6DN)
6-CHANNEL
FP-T5
(for
FP-5)
5-CHANNEL
Loading...