Futaba FP3FN, FP4FN, FP5FN, FP6FN User Manual
FP-6FN 6ch. FP-5FN 5ch.
FP-4FN 4ch. FP-3FN 3ch.
INDEX
Features
Composition and Specifications
Transmitter
Receiver
FUTABA trainer
Operating instructions
Nickel-cadmium battery and charging methods
Performance test and mounting precautions.....................
FUTABA proportional
Guarantee.....................................................................
Factory repair service
.....................................................................
....................................
handling
and
instructions
servo
handling instructions
system
................................................
...................................................
frequencies
...................................................
....................................
........................
...............
.................................
FEATURES OF THE NEW FUTABA PROPORTIONAL
RADIO CONTROL SYSTEM
TRANSMITTER (FP—T6FN. FP—T5FN. FP—T4FN, FP—T3FN)
1. Since all Futaba New Proportional Models are designed and manufactured to identical standards, maximum
performance is displayed even when used with other receivers and servos.
2. Position of throttle control can be easily changed (to left or right).
3. Hook band permits hanging the transmitter from your neck for extremely easy handling.
4. Training system provided as standard makes training of beginners easy.
5. Equipped with a stand.
RECEIVER (FP—R6F. FP—R4F, FP—R3F)
1. Newly developed receiver use FUTABA CUSTOM 1C (IR-014, or BA-633) is extremely stable against power supply
voltage fluctuations.
2. Eight-bit CMOS 1C has complete 6-channel operation functions and reduces power consumption to a minimum.
3. Resistance against interference has been strengthened considerably through the adoption of a RF amplifier circuit
and ceramic filter.
SERVO (FP—S7. FP—S12. FP—S16. FP—S16L. FP—S17, and FP—S8, FP—S16G
[retractable landing gear servo])
1. Since the FP-S7, FP-S12, FP-S16, FP-S16L, FP-S17, and FP-S8, FP-S16G (retractable landing gear servo) are
designed and manufactured to the same standards, top performance is displayed when used with any NEW
FUTABA PROPORTIONAL transmitter and receiver.
2. Three-wire, compact, lightweight, rugged, high-output torque servoamps have been realized through the use of
Futaba BA-607 and BA-606 custom monolithic 1C.
3. The BA-607 monolithic 1C is a 12-pin single-end-line 1C containing 73 transistors, 13 diodes, and 79 resistors (total
of 165 components). Its low current drain, high resolution, temperature compensation and built-in voltage regulator
assure stable operation over the 4V— 6.6V power supply voltage range without any mutual interference between
servos. A
4. The BA-606 monolithic 1C is a 9-pin single-end-line 1C incorporating 2 high output current (500mA)
sistors, 2 NPN transistors, 4 diodes, and 4 resistors for a total of 12 components on a single chip.
5. High output torque: FP-S7; 3 kg-cm, FP-S12; 2.8kg-cm, FP-S16 (S16L); 2kg-cm, FP-S17; 2.6kg-cm, and FP-S8,
FP-S16G (retractable landing gear servo); 8kg -cm, 2.6kg -cm.
6. Compact, lightweight: FP-S7; 48g, FP-S12; 52g, FP-S16 (S16L); 41 g, FP-S17; 44g, and FP-S8; 50g, FP-S16G; 41g.
7. The 20mm (dia.) motor of the FP-S7 servo provides power torque. Thus making it ideal for
use. Waterproof case also makes it perfect for use in both fresh water and salt water areas.
8. FP-S12 is a low cost servo and powerful torque of 2.8kg -cm or greater permits use not only in large buggies,
but also in Class 60 boats, etc.
9. The potentiometer drive section of the FP-S16 (S16L) is separately driven through a one-stage gear. The life of
the element is almost permanent.
10. FP-S17 is a lightweight, rugged, high output, and low cost servo.
11. The high gear ratio and powerful torque of the FP-S8 make it the perfect retractable landing gear servo.
12. FP-S16G is a highest class miniature landing gear servo.
boat and automobile
PNP
tran-
COMPOSITION AND SPECIFICATIONS
• COMPOSITION:
Transmitter/receiver nickel-cadmium battery
Model
Number of channels
Transmitter
Receiver
Servo
Battery charger
PP-6FN
6CH
FP-T6FN
FP-R6F
FP-S16 x 3
FP-S16Lx1
FP-5FN
5CH
FP-T5FN
FP-S16x3
FP-S16Lx1
Nickel-cadmium charger FBC—2(F)
FP-4FN
4CH
FP-T4FN
FP-R4F
FP-S16x3
FP-S16Lx1
FP-3PN
3CH
FP-T3FN
FP-R3F
(FP-S7 x 2
FP-S16 x 2 FP-S12x2
FP-S17 x 2)
• SPECIFICATIONS:
Operating system......... CH1—4, 2-stick system, CH5 snap
Operating frequencies... 27MHz band 72MHz band
Antenna output............
Modulation
system
......
Power requirement......
Current drain............... 140mA
Receiving frequencies... 27MHz band 72MHz band
IF amplifier frequency... 455kHz
Selectivity
Range
..................
........................
Power requirement...... 4.8V 4/450mAH nickel-cadmium
Current
drain...............
Dimensions
...............
Weight........................ FP-R6F:
(All
specifications
are
TRANSMITTER
switch, CH6 trim lever system
40 MHz band
500mW
AM
(amplitude
modulation)
Pulse position modulation:
1310uS neutral (Pulse spacing)
9.6V 8/450mAH nickel-cadmium
battery
RECEIVER
40MHz band
3kHz/-3dB
500m
on
the
ground,
1000m
battery
4.8V 10mA
FP-R6F:
40
x69
FP-R4F,
R3F:
x19mm
40.2x58.5
52g
FP-R4F. R3F: 46 g
subject
in the air
x19mm
to change
without
prior
notice.)
SERVO (FP-S7, FP-S12, FP-S16, FP-S16L,
FP-S17, FP-S8, FP-S16G)
Control
system
............
3-wire, + pulse
width control
650uS~ 1900uS
Operating angle............
Rotary system one side 45° min
(including trim) FP-S7. FP-S12,
FP-S17
Rotary system one side 80° min FP-S8.
FP- S16G (retractable landing gear servo)
Power requirement...... 4.8V 4/450mAH nickel-cadmium battery
(used in conjunction with receiver)
Current
drain...............
Output torque ............
4.8V
8mA
(when
stopped)
FP-S7; 3kg-cm, FP-S12: 2.8 kg-cm,
FP-S16; 2kg-cm, FP-S17: 2.6kg-cm,
FP-S8: 8 kg-cm, FP-S16G: 2.6 kg-cm.
Dimensions.................. FP-S7:
23 x 44 x 41 mm.
FP-S12: 23 x 44.5 x 42.5 mm,
FP-S16:19.5x41 5x35.5mm,
FP-S17: 20 x 39.6 x 40 mm,
FP-S8; 23x44x41 mm,
FP-S16G: 19.5 x 41.5 x 35.5 mm
Weight........................ FP-S7:
48g,
FP-S12;
52g,
FP-S17; 44g. FP-S8: 50g, FP-S16G; 41g.
BATTERY CHARGER (Nickel-cadmium charger)
Input
voltage
Frequency
...............
..................
115V
(220V,
50/60Hz
240V)
Power consumption ... 2.0/3.5VA
Output
Tx.
Output
..................
NOTE:
Power consumption is for no load/load. Since the transformer may be burned up or the performances of the battery will deteriorate due to
an
overcurreni if the NR-4C nickel-cadmium battery is connected to the Tx output terminals, always be sure that connections are correct.
Rx................... 4.8V, 45mA
9.6V, 45mA
FP-S16.
FP-S16;
41g,
TRANSMITTER HANDLING INSTRUCTIONS
FP T6FN
(forFP -6FN)
6 CHANNEL
FP-T5FN
(tor
FP-5FN)
5-CHANNEL
Fig.
FP-T4FN
(for
FP
4FN)
4-CHANNEL
1
FP-T3FN
(for FP-3FN)
3-CHANNEL
Loading...