How it Works
FUTABA
Loading...
FMT-03
Instruction Manual
68 pgs4.86 Mb0

FUTABA FMT-03 Instruction Manual

Download
1M23Z04404
For model
INTRODUCTION............................................... 4
●Support and Service ......................................... 4
●Application, Export, and Modication ........... 4
●Denitions of Symbols ...................................... 7
●Safety Precautions (do not operate without
reading) ............................................................. 7
BEFORE USE ................................................... 11
●Features of FMT-03 ....................................... 11
●Contents and technical specications ...........12
●Accessories ....................................................... 13
●Transmitter controls ....................................... 14
Transmitter's antenna .................................... 15
Switch (SA-SH) ............................................... 17
Volume (DA-DD) ............................................ 17
Monitor LED .................................................. 17
Edit dial ........................................................... 17
Home/Exit, U.menu/Mon. Button ................. 19
Maintenance example of a transmitter ........ 19
Micro SD Card ............................................... 20
Connector ........................................................ 21
Installation and removal of the battery ........ 22
●Receiver FMR-03 ............................................ 23
●Telemetry sensor ............................................. 24
●S.BUS2 servo ................................................... 24
●Receiver's antenna installation ...................... 25
●Mounting the servo ......................................... 26
●Safety precautions when installing servos ... 26
●S.BUS2 Devicesetting ..................................... 27
BASIC OPERATION ....................................... 28
●Battery Charging ............................................ 28
●How to turn transmitter power ON/OFF .... 29
●Registration of the user's name ..................... 29
●Home screen .................................................... 30
●User menu ........................................................ 31
●Key lock ........................................................... 32
●Link procedure ..............................................33
●Range testing your R/C system...................... 35
●Channels connection by multicopter type .... 36
FUNCTIONS OF SYSTEM MENU ................ 37
Display ............................................................. 38
System Timer .................................................. 39
User Name ....................................................... 40
H/W Setting ..................................................... 42
Information .................................................... 44
Range Check .................................................. 45
S.BUS Servo ................................................... 46
FUNCTIONS OF LINKAGE MENU .............49
Linkage Menu functions table ...................... 49
Servo Monitor ................................................. 50
Model Select .................................................... 51
Model Type (This function isn't used) .......... 53
System Type .................................................... 54
Function .......................................................... 56
Sub-Trim ......................................................... 58
Servo Reverse ................................................. 59
End Point ........................................................ 61
Throttle Cut ................................................... 62
Idle Down ....................................................... 63
Timer ............................................................... 64
T1-T6 Setting .................................................. 66
Multiprop ........................................................ 67
Function Name ............................................... 68
Telemetry......................................................... 69
Telemetry:receiver [battery] ......................... 70
Telemetry:receiver [EXT-batt] ...................... 71
Telemetry:temperature .................................. 72
Telemetry:altitude .......................................... 74
Telemetry:voltage [battery] ........................... 76
Telemetry:voltage [EXT-volt] ........................ 77
TABLE OF CONTENTS
TABLE OF CONTENTS
Telemetry:GPS [distance] .............................. 78
Telemetry:GPS [speed] .................................. 80
Telemetry:GPS [
altitude,variometer,position
] .....81
Telemetry:Servo sensor
[current] [temperature]
[angle]
............................................................. 82
Telemetry:Current sensor
[current] [voltage]
[capacity]
......................................................... 83
Sensor .............................................................. 84
Sensor:reload .................................................. 85
Sensor:register ................................................ 85
Sensor:change slot .......................................... 86
Warning ...........................................................88
Trainer ............................................................. 89
Stick Alarm ..................................................... 92
Data Reset ....................................................... 93
FUNCTIONS OF MODEL MENU ................. 94
●Common Functions ........................................ 94
Condition Select ............................................. 95
AFR ................................................................ 97
Dual Rate ........................................................ 98
Program Mix ................................................... 99
Gyro ............................................................... 103
DATA ................................................................ 104
●Common Operations used in function setup
screen ............................................................. 104
●Updating ........................................................ 112
Reference.......................................................... 113
●Airplane/Glider Functions ........................... 114
Servo connection by airplane/glider type ... 116
AIL Differential ............................................ 120
Flap Setting ................................................... 121
AIL to Brake FLP ......................................... 123
Airbrake to ELE ........................................... 125
RUD to AIL ................................................... 127
Camber Mix .................................................. 128
ELE to Camber ............................................ 130
Camber FLP to ELE .................................... 131
Buttery ........................................................ 132
Trim Mix 1/2 ................................................. 134
Airbrake (Airplane only) ............................. 136
Gyro (for GYA type gyro) ............................ 138
V-tail .............................................................. 140
Ailevator ........................................................ 141
Winglet .......................................................... 142
Acceleration .................................................. 144
RUD to ELE .................................................. 145
Snap Roll (Airplane only) ............................ 146
●Helicopter Functions .................................... 147
Servo connection by helicopter type ........... 148
PIT Curve ..................................................... 149
PIT trim ......................................................... 150
THR Curve ................................................... 152
Throttle hover trim ...................................... 153
Acceleration .................................................. 155
THR Hold ...................................................... 156
Swash Mix ..................................................... 157
Throttle Mix .................................................. 158
PIT to Needle ................................................ 159
PIT to RUD (Revolution mix) ..................... 160
Gyro (for GY type gyro) .............................. 161
Governor ....................................................... 162
Cond. Hold .................................................... 164
Reference
FMT-03 is equipped with a stick of multi-copter exclusive use. Therefore it's unsuitable for use of an airplane, a glider and a helicopter.
4
<Introduction>
INTRODUCTION
Thank you for purchasing a Futaba
®
FASSTest-2.4GHz* FMT-03 series digital proportional R/
C system. In order for you to make the best use of your system and to y safely, please read this
manual carefully.
*FASSTest: Futaba Advanced Spread Spectrum Technology extend system telemetry
Due to unforeseen changes in production procedures, the information contained in this manual is
subject to change without notice.
FOR SUPPORT :
(PROGRAMMING AND USER QUESTIONS)
FUTABA Corporation of America
101 Electronics Boulevard, Huntsville, Alabama 35824, U.S.A
Fax: 1-256-461-1059
Phone: 1-256-461-9399
OUTSIDE NORTH AMERICA
Please contact your Futaba importer in your region of the world to assist you with any questions,
problems or service needs.
Please recognize that all information in this manual, and all support availability, is based upon
the systems sold in North America only. Products purchased elsewhere may vary. Always contact your region’s support center for assistance.
Application, Export, and Modication
1. This product may be used for unmanned aerial vehicle use. It is not intended for use in any application other than the control of models for unmanned aerial vehicle. The product is subject to regulations of the Ministry of Radio/Telecommunications and is restricted under Japanese law to such purposes.
2. Exportation precautions:
(a) When this product is exported from the country of manufacture, its use is to be approved by
the laws governing the country of destination which govern devices that emit radio frequencies. If
this product is then re-exported to other countries, it may be subject to restrictions on such export.
Prior approval of the appropriate government authorities may be required. If you have purchased
this product from an exporter outside your country, and not the authorized Futaba distributor in your country, please contact the seller immediately to determine if such export regulations have
been met. (b) Use of this product with other than models may be restricted by Export and Trade Control
Regulations, and an application for export approval must be submitted. This equipment must not
be utilized to operate equipment other than radio controlled models.
3. Modication, adjustment, and replacement of parts: Futaba is not responsible for unauthorized modication, adjustment, and replacement of parts on this product. Any such changes may void
the warranty.
5
<Introduction>
Compliance Information Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following three
conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
(3)RF Radiation Exposure Statement (For FMT-03) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Radiation Exposure Statement (For FMR-03) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
The responsible party for the compliance of this device is: FUTABA Corporation of America
101 Electronics Boulevard, Huntsville, Alabama 35824, U.S.A Fax: 1-256-461-1059 Phone: 1-256-461-9399
The RBRC. SEAL on the nickel-cadmium battery contained in Futaba products indicates that Futaba Corporation is voluntarily participating in an industry-wide
program to collect and recycle these batteries at the end of their useful lives, when
taken out of service within the United States. The RBRC. program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or
municipal waste system, which is illegal in some areas.
(for USA) You may contact your local recycling center for information on where to return the spent battery.
Please call 1-800-8BATTERY for information on NiCd battery recycling in your area. Futaba
Corporation involvement in this program is part of its commitment to protecting our environment and conserving natural resources.
*RBRC is a trademark of the Rechargeable Battery Recycling Corporation.
NOTE:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. (For FMT-03)
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. (For FMR-03)
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation de ce dispositif
est autorisée seulement aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout brouillage radioélectrique reçu, même si
ce brouillage est susceptible de compromettre le fonctionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet émetteur ne doit pas être co-situé ou fonctionner conjointement avec une autre antenne ou émetteur. (For FMT-03)
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps (For FMR-03)
6
<Introduction>
FLYING SAFETY
WARNING
To ensure the safety of yourself and others, please observe the following precautions:
Have regular maintenance performed. Although your FMT-03 protects the model memories with
non-volatile EEPROM memory (which does not require periodic replacement) and not a battery, the
transmitter still should have regular checkups for wear and tear. We recommend sending your system
to the Futaba Service Center annually during your non-ying-season for a complete checkup and
service.
Battery
Charge the batteries! Always recharge the transmitter and receiver batteries before each ying
session. A low battery will soon die potentially, causing loss of control and a crash. When you begin your ying session, reset your FMT-03’s built-in timer, and during the session pay attention to the
duration of usage.
Stop ying long before your batteries become low on charge. Do not rely on your radio’s low battery warning systems, intended only as a precaution, to tell you when to recharge. Always check your transmitter and receiver batteries prior to each ight.
Where to Fly
We recommend that you y at a recognized model airplane ying eld. You can nd model clubs and elds by asking your nearest hobby dealer, or in the US by contacting the Academy
of Model Aeronautics.
You can also contact the national Academy of Model Aeronautics (AMA), which has more than 2,500 chartered clubs across the country. Through any one of them, instructor training
programs and insured newcomer training are available. Contact the AMA at the address or toll­free phone number below.
Academy of Model Aeronautics
5161 East Memorial Drive
Muncie, IN 47302
Tele. (800) 435-9262
Fax (765) 289-4248
or via the Internet at http:\\www.
modelaircraft.org
Always pay particular attention to the ying eld’s rules, as well as the presence and location
of spectators, the wind direction, and any obstacles on the eld. Be very careful ying in areas near power lines, tall buildings, or communication facilities as there may be radio interference in their
vicinity.
CAUTION:
To assure continued FCC compliance:
Any changes or modications not expressly approved by the grantee of this device could void the
user's authority to operate the equipment.
This radio transmitter (identify the device by certication number) has been approved by Industry
Canada to operate with the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
No. Name Gain(Peak) Remark
1 MEIWX-2102RSAX-2400 2.25dBi 1/2 λ Pencil type antenna
7
<Introduction>
Precautions
Application, Export, and Modification Precautions.
1. This product is only designed for use with radio control models. Use of the product described in this instruction manual is limited to radio control models.
2. Export precautions:
a) When this product is exported, it cannot be used where prohibited by the laws governing radio waves of the
destination country.
b) Use of this product with other than models may be restricted by Export and Trade Control Regulations.
3. Modification, adjustment, and parts replacement
Futaba is not responsible for unauthorized modification, adjustment, or replacement of parts on this product.
■
No part of this manual may be reproduced in any form without prior permission.
■
The contents of this manual are subject to change without prior notice.
■
Futaba is not responsible for the use of this product by the customer.
■
Company and product names in this manual are trademarks or registered trademarks of the respective company.
Please observe the following precautions to ensure safe use of this product at all times. Meaning of Special Markings: The parts of this manual indicated by the following marks require special attention from the standpoint of safety.
DANGER - Procedures which may lead to dangerous conditions and cause death/serious injury if not
carried out properly.
WARNING - Procedures which may lead to a dangerous condition or cause death or serious injury to the
user if not carried out properly, or procedures where the probability of supercial injury or physical damage is high.
CAUTION - Procedures where the possibility of serious injury to the user is small, but there is a danger of
injury, or physical damage, if not carried out properly.
= Prohibited
= Mandatory
WARNING: Always keep electrical components away from small children.
For safe use
Flying Precautions
WARNING
Never grasp the transmitter antenna while
ying.
■ The transmitter output may drop drastically.
Always make sure that all transmitter stick movements operate all channels properly in the model prior to flight. Also, make sure that all switches, etc. function properly as well. If there are any di󱐰culties, do not use the system until all inputs are functioning properly.　
Never y in the range check mode.　
■ In the dedicated range test range check mode, the transmitter output range is reduced and may cause a crash.
While operating, never touch the transmitter with, or bring the transmitter near, another transmitter, a cellphone, or other wireless devices.
■ Doing so may cause erroneous operation.
Do not point the antenna directly toward the aircraft during ight.　
■ The antenna is directional and the transmitter output is weakest. (The strength of the radio waves is greatest from the sides of the antenna.)
Never fly on a rainy day, when the wind is
strong, and at night.　
■ Water could lead to failure or improper functionality and poor control of the aircraft which could lead to a crash.
Never turn the power switch on and o󱐯 during
ight or while the engine or motor is running.　
■ Operation will become impossible and the aircraft will crash. Even if the power switch is turned on, operation will not begin until transmitter and receiver internal processing is complete.
Do not fly when you are physically impaired as it could pose a safety hazard to yourself or others.
Do not touch the engine, motor, or motor
controller during and immediately after use.　　
■ These items may become hot during use.
8
<Introduction>
Battery and Charger Handling Precautions
DANGER
Do not charge and store the battery in direct sunlight or other hot places.　　　
Do not charge the battery if it is covered with any object as it may become very hot.
Do not use the battery in a combustible
environment.　
■ The gas ignite and cause an explosion or fire.
Always charge the battery before each ying session.　
■ If the battery goes dead during flight, the aircraft will crash.
Do not y at the following places:　　　
■ Near another radio control flying field.
■ Near or above people.
■ Near homes, schools, hospitals or other places where people congregate.
■ Near high voltage lines, high structures, or communication facilities.
For safety, y so that the aircraft is visible at
all times.　　　
■ Flying behind buildings or other large structures will not only cause you to lose sight of the aircraft, but also degrade the RF link performance and cause loss of control.
From the standpoint of safety, always set the
fail safe function.　　　
■ In particular, normally set the throttle channel to idle.
When flying, always return the transmitter
setup screen to the Home screen.　　　
■ Erroneous input during flight is extremely dangerous.
Always check the remaining capacity of the transmitter and receiver battery before each ying session prior to ight.　
■ Low battery capacity will cause loss of control and a crash.
Always check operation of each control functions and perform a range test before each flying session. Also, when using the trainer function, check the operation of both the teacher and student transmitter.　
■ Even one transmitter setting or aircraft abnormality cause a crash.
Before turning on the transmitter:
1. Always move the transmitter throttle stick　 position to the minimum (idle) position.　
2. Turn on the transmitter first and then the　 receiver.
When turning off the transmitter's power switch. After the engine or motor has stopped (state in which it will not rotate again):
1. Turn o󱐯 the receiver power switch.　
2. Then turn o󱐯 the transmitter power switch.
■ If the power switch is turned on/off in the opposite order, the propeller may rotate unexpectedly and cause a serious injury.
■ Also always observe the above order when setting the fail safe function.
■ Maximum low throttle: Direction in which the engine or motor runs at the slowest speed or stops.
When adjusting the transmitter, stop the engine except when necessary. In the case of a motor, disconnect the wiring and to allow it to continue operation. When doing so, please exercise extreme caution. Ensure that the aircraft is secured and that it will not come into contact with anything or anyone. Ensure that the motor will not rotate prior to making any adjustments.
■ Unexpected high speed rotation of the motor/engine may cause a serious injury.
Do not recharge a battery that is damaged,
deteriorated, leaking electrolyte, or wet.　
Do not use the charger in applications other
than as intended.
Do not allow the charger or battery to become
wet.
■ Do not use the charger when it or your hands are wet. Do not use the charger in humid places. 　　
Do not short circuit the battery.　　
Do not solder or repair, deform, modify, or
disassemble the battery and/or battery charger.
Do not drop the battery into a re or bring it
near a re.　　　
9
<Introduction>
Charge the battery with the dedicated charger
supplied with the set.
■ Charging the battery past the specified value may cause a re, combustion, rupture, or liquid leakage. When quick charging, do not charge the battery above 1C.
■ Do not charge the battery while riding in a vehicle. Vibration will prevent normal charging.
When using the LiFe battery, do not connect the charger to the balance charge connector and the power connector at the same time.　
■ Doing so could cause a re, combustion, generation of heat, rupture, or liquid leakage.
Insert the power cord plug firmly into the
receptacle up to its base.
Always use the charger with the specified
power supply voltage.
■ Use the special charger by connecting it to a proper power outlet.
If the battery liquid should get in your eyes, do not rub your eyes, but immediately wash them with tap water or other clean water and get treated by a doctor.
■ The liquid can cause blindness. 　
Do not touch the charger and battery for any
length of time during charging.　
■ Doing so may result burns. 　　　
Do not use a charger or battery that has been
damaged.　　
Do not touch any of the internal components
of the charger.　　　
■ Doing so may cause electric shock or a burn.
If any abnormalities such as smoke or discoloration are noted with either the charger or the battery, remove the battery from the transmitter or charger and disconnect the power cord plug and do not use the charger.　
■ Continued use may cause fire, combustion, generation of heat, or rupture.
Do not subject the battery to impact.
■ Doing so may cause fire, combustion, generation of heat, rupture, or liquid leakage.
WARNING
Use and store the battery and battery charger
in a secure location away from children.　
■ Doing so may cause electric shock or injury.
If the battery leaks liquid or generates an abnormal odor, immediately move it to a safe place for disposal.
■ Not doing so may cause combustion.
If the battery liquid gets on your skin or clothing, immediately flush the area with tap water or other clean water.
■ Consult a doctor. The liquid can cause skin damage.
After the specied charging time has elapsed, end charging and disconnect the charger from the receptacle.　
When recycling or disposing of the battery, isolate the terminals by covering them with insulating tape.
■ Short circuit of the terminals may cause combustion, generation of heat or rupture.
CAUTION
Do not use the battery with devices other than
the corresponding transmitter.　　　
Do not place heavy objects on top of the battery or charger. Also, do not place the battery or charger in any location where it fall.　　 　　
■ Doing so may cause damage or injury.
Do not store or use the battery and charger
where it is dusty or humid.　
■ Insert the power cord plug into the receptacle only after eliminating the dust.
After the transmitter has been used for a long time, the battery may become hot. Immediately remove from the transmitter.
■ Not doing so may cause a burn.
Do not charge the battery in extreme
temperatures.
■ Doing so will degrade the battery performance. An ambient temperature of 10 ℃ to 30 ℃ (50F to 86F) is ideal for charging.
Unplug the charger when not in use.　
Do not bend or pull the cord unreasonably
and do not place heavy objects on the cord.
■ The power cord may be damaged and cause combustion, generation of heat, or electric shock.
10
<Introduction>
Never disassemble or modify the micro SD
Card.　
Do not unreasonably bend, drop, scratch or place heavy objects on the micro SD Card.
Since the micro SD Card is an electronic
device, be careful of static electricity.　
■ Static electricity may cause erroneous operation or trouble.
Do not use the micro SD Card near radio and television sets, audio equipment, motors and other equipment that generate noise.　
■ Doing so may cause erroneous operation.
Do not store the micro SD Card in the
following places:　
・ Where the humidity is high ・ Where the temperature difference is severe
Micro SD Card (Commercial Product) Handling Precautions
WARNING
CAUTION
*Read the instruction manual supplied with
the micro SD Card for details.
●Recorded data
The data recorded on the micro SD Card cannot be compensated regardless of the contents or cause of the trouble or obstruction. Futaba does not perform data restoration or recovery work.
If smoke or an abnormal odor emanates from the card, immediately turn off the transmitter power. 　　　
Do not use the Micro SD Card where it may be exposed to water, chemicals, oil, or other uids.
■ Doing so may cause a fire or electric shock by short circuit.
・ Where it is very dusty ・ Where the card will be exposed to shock and vibration ・ Near speakers and other magnetic devices
Do not expose the card to shock and vibration and do not remove the card from the card slot while data is being written or read.　
■ The data may be damaged or lost.
Keep wireless equipment, batteries, aircraft,
etc. away from children.　
Storage and Disposal Precautions
WARNING
Do not store wireless devices in the following
places:　
・ Where it is extremely hot (40 ℃ [104F] or higher) or
cold (-10℃ [14F] or lower)
・ Where the equipment will be exposed to direct　
sunlight ・ Where the humidity is high ・ Where vibration is prevalent ・ Where it is very dusty
CAUTION
・ Where the device may be exposed to steam and heat
When the device will not be used for a long time, remove the battery from the transmitter and aircraft and store them in a dry place where the temperature is between 0 and 30℃ [32F and 86F].　
■ Left standing 'as is' may will cause battery deterioration, liquid leakage, etc.
Do not directly expose plastic parts to fuel, oil,
exhaust gas, etc.　
■ If left in such an environment, the plastic may be attacked and damaged.
■ Since the metal parts of the case may corrode, always keep them clean.
Always use genuine Futaba products such as transmitter, receiver, servo, FET amplifier, battery, etc.　
Other Precautions
CAUTION
■ Futaba is not responsible for damage sustained by combination with other than Futaba Genuine Parts. Use the parts specified in the instruction manual and catalog.
This product SHOULD NOT been used for the devices that is directly related to human life and/ or harmful devices for human body such as below applications.
(1) Medical Devices (2) Aerospace/Aviation Related Devices (3) Nucleated Devices e.t.c.
11
<Before Use>
BEFORE USE
Features
FASSTest system
The FMT-03 transmitter has adopted the newly developed bidirectional communication system "FASSTest". Data from the receiver can be checked in your transmitter. FASSTest is a maximum 18channels (linear 16 channels + switch 2 channels) 2.4GHz dedicated system.
Waterproof:IP-64
The FMT-03 transmitter and FMR-03 receiver are waterproong (IP-64).
S.BUS/S.BUS2 system
By using the S.BUS/S.BUS2 system multiple servos, gyros and telemetry sensors are easily
installed with a minimum amount of cables.
LiFe battery
FMT-03 is operated by a 6.6V/2,100mAh Lithium Ferrite battery.
Micro SD card (Secure Digital memory card) (Not included)
Model data can be saved to a micro SD card (SD:32MB-2GB SDHC:4GB-32GB). When FMT-03
transmitter software les are released, the software can be updated by using a micro SD card update.
Data input
Large graphic LCD and Edit dial substantially improve ease of setup.
Edit button
Edit dial and three edit buttons are provided, and the operating screen can be immediately “Returned” to the HOME screen during operation. Setting operation can be performed easily by combining this button with a Edit dial.
Vibration function
Selects a function that alerts the operator to various alarms by vibrating the transmitter in addition to sounding a buzzer.
12
<Before Use>
Contents and Technical Specications
(Specications and ratings are subject to change without notice.)
Your FMT-03 includes the following components:
• FMT-03 Transmitter
• FMR-03 Receiver
• FT2F2100BV2 LiFe battery & charger
*The set contents depend on the type of set.
Transmitter FMT-03
(2-stick, 18-channel, FASSTest-2.4GHz system)
Transmitting frequency: 2.4GHz band
System: FASSTest 18CH, FASSTest 12CH switchable
Power supply: 6.6V FT2F2100BV2 LiFe battery
Receiver FMR-03
(FASSTest-2.4G system, dual antenna diversity, S.BUS/S.BUS2 system)
Power requirement: 3.7V~7.4V battery or regulated output from ESC, etc. (*1)
Size: 0.92 x 1.36 x 0.42 in. (23.4 x 34.6 x 10.6 mm)
Weight: 0.11 oz. (3g)
(*1) When using an ESC make sure that it is capable of your applications current draw.
Note: The battery in the FMT-03 transmitter is not connected to the battery connector at initial. Please connect the battery connector before use.
13
<Before Use>
• FT2F2100BV2 transmitter battery pack - the (2,100mAh) transmitter LiFe battery pack may be easily exchanged with a fresh one to provide enough capacity for extended ying sessions.
• Trainer cord - the optional training cord may be used to help a beginning pilot learn to fly easily by placing the instructor on a separate transmitter. Note: FMT-03 is connected by an exclusive trainer code by FMT-03 fellow. It isn't possible to connect with a transmitter of the different model.
• Servos - FMR-03 can use only futaba S.BUS2 servos.
• Telemetry sensor - please purchase an optional sensor, in order to utilize bidirectional communication system and to acquire the information from a model high up in the sky.
[
Temperature sensor : SBS-01T/TE] [Altitude sensor : SBS-01A] [RPM sensor magnet type : SBS­01RM][RPM sensor optical type : SBS-01RO] [RPM sensor brushless motor type : SBS-01RO] [GPS sensor : SBS-01G] [Voltage sensor : SBS-01V] [S.BUS servo sensor : SBS-01S] [Current sensor : SBS­01C]
• Y-harnesses, servo extensions, hub,etc - Genuine Futaba extensions and Y-harnesses, including a heavy­duty version with heavier wire, are available to aid in your larger model and other installations.
• Receivers - various models of Futaba receivers may be purchased for use in other models. (Receivers for FASSTest types are available.)
The following additional accessories are available from your dealer. Refer to a Futaba catalog for more information:
14
<Before Use>
●Antenna
●Monitor LED
●Speaker
●Stick
●Stick
●U.menu/Mon 　Button
●Home/Exit Button
●S1 Button
●RTN Button
●Edit dial
●LCD
●Power Switch
●Switch SB
●Switch SA
●Switch SC
●Switch SD
●Switch SF
●Switch SE
●Switch SG
●Switch SH
●Volume(DA)
●Volume(DC)
●Volume(DB)
●Volume(DD)
J2
J1
J3
J4
Transmitter controls
CAUTION
This transmitter is a self neutral stick. A throttle stick of a transmitter for R/ C hobbies of normality is a ratchet-type. Notice should be taken of this difference. When you release your hold, it becomes middle-speed, so be careful.
15
<Before Use>
Transmitter's Antenna:
As with all radio frequency transmissions, the strongest area of signal transmission is from the sides of the transmitter's antenna. As such, the
antenna should not be pointed directly at the model.
If your flying style creates this situation, easily
move the antenna to correct this situation.
• Rotating antenna
The antenna can be rotated 360 degrees and angled 90 degrees. Forcing the antenna further than this can damage it. When making an antenna rotate, be careful so that xing screw doesn't loosen.
Low power
High power High power
Place the antenna at an angle 90 degrees to the aircraft.
It is not good to point the antenna at a ying model.
90°
360°
Be careful so that antenna xing screw doesn't loosen.
16
<Before Use>
CAUTION
Be sure to install an antenna and do a
ight.
■
When there are no antennas, you can't control.
Please do not grasp the transmitter's
antenna during ight.
■
Doing so may degrade the quality of the RF
transmission to the model.
Do not carry the transmitter by the
antenna.
■
There is the danger that the antenna wire will break
and operation will become impossible.
Do not pull the antenna forcefully.
■
There is the danger that the antenna wire will break
and operation will become impossible.
Attachment and removal of an antenna
FMT-03 can attach or remove an antenna.
Dust and water aren't supposed to be stuck in an
antenna connector.
Antenna screw
Rotation part
Install of an antenna straight to a screw. Tighten a screw tightly so as not to loosen.
Antenna
This nut isn't removed.
17
<Before Use>
Switch (SA-SH)
You can choose switch and set the ON/OFF­direction in the setting screen of the mixing
functions.
Volume
Volume DA - DD:
The volume DA-DD knobs allow analog input.
*The FMT-03 transmitter beeps when the volume knob
reaches the center position.
*You can use each setting screen of the mixing functions to
select volumes and dene the direction of a movement.
DA
DC
DB
DD
SA SC
SF SH
SE
SG
SB SD
Monitor LED
•
RF-ON → Light Blue light
•
RF-OFF → Violet light
•
Starting → Red light
•
Trainer Student → Blue light
•
Range check mode → Slow blinking
•
FASSTest receiver link mode → Fast
blinking
Monitor LED display
The status of the transmitter is displayed by LED at
the upper part of the front of a FMT-03.
Edit dial
Scroll
Push RTN
18
<Before Use>
S1
RTN
S1
RTN
S1
Edit dial operation Action Reaction
• Short 'push'
S1
If the screen has more than one page.
The cursor moves to the top of next page.
If the screen have only one (1) page. The cursor moves to the top of page.
If the input data mode with blinking the setting data. The input data is canceled.
RTN
At the moving cursor mode. Change to the input data mode.
At the input data mode. Change to the moving cursor mode.
At the input data mode with blinking the setting data. The data is entered.
• Push and hold for one (1) second.
S1
At the HOME screen Key lock On or Off
RTN
In the input data mode without blinking the setting data.
Reset to the initialized value.
• Scrolling
Outline
of
Edit
dial
Turn the outline of the edit dial. The cursor moves accordingly.
During the data input mode. Increases or decreases values accordingly.
Edit dial operation
Data input operation is performed using the edit dial.
Movement of cursor, value input or mode selection
:
Movement of the cursor on the menu screen and
movement of the cursor among items on a setup screen can be controlled by scrolling your finger to the left and right in the direction of the arrow in the scrolling diagram above. You can also go to the next page, if there is a next page.
This scrolling technique is also used for data input, value input, mode selection, and similar operations. Examples include: Value, ON, OFF, INH, ACT, etc.
RTN button:
Push the RTN button when you want to open a
setup screen or to switch between cursor move mode (reverse display) and data input mode (box display).
This button can also be used as the enter button
when a conrmation message is displayed on the screen, etc.
S1 button:
When there is a next page on a menu screen or setup screen, you can go to that page by pushing the S1 button. In this case, the cursor moves to the screen title item of the page.
Exiting setup screen:
To end the operation on a setup screen and
return to the menu screen, move the cursor to the screen title item and push the RTN button.
To return to home screen directly, push the Home/Exit button for 1 second.
Alternatively, move the cursor to the screen title item and push the RTN button to return to the
home screen from a menu screen.
19
<Before Use>
Home/Exit and U.menu/Mon. Button
Home/Exit
Button
U.menu/Mon
Button
Push To Servo Monitor display
Push and hold To User menu
Home/Exit:
U.menu/Mon:
Push
Return to the previous
screen
Push and hold Return to the Home screen
It pushes from
HOME screen.
To TELEMETRY display
Maintenance example of a transmitter
Tripod Screw
Hole
Camera Tripods or
Monopods.
(not included)
Hole of the VESA (VIDEO ELECTORONICS STANDARDS ASSOCIATION) standard is equipped in FMT-03. It's also possible to install it
in the display arm (not included).
2 sticks of FMT-03 can do linear operation in left, right, up or down.
Operation of sticks
20
<Before Use>
Micro SD card
(secure digital memory card) (not
included)
The FMT-03 transmitter model data
can be stored by using any commonly
found micro SD card. When FMT­03 transmitter update software is
released, the software is updated using
an micro SD card. The FMT-03 is
capable of using micro SD cards with
a memory size between SD:32MB
-2GB SDHC:4GB-32GB.
CAUTION
Be sure to turn off the power to the transmitter before inserting or removing the micro SD card.
As the micro SD card is a precision device,
do not use excessive force when inserting.
Micro SD card reader/writer
Saving model data and update files (released from Futaba) into the micro SD card, you can use those les on your FMT-03 transmitter. Equipment for reading and writing micro SD cards is available
at most electronics stores.
Stored data
When you have a problem of saving or reading data after a long period of use, please get a new
micro SD card.
*We do not have the responsibility of compensating any
failure or damage to the data stored in the memory card no
matter what the reason is. Be sure to keep a backup of your important data in your micro SD card.
Inserting/removing the micro SD card
② It inserts until it locks micro SD card into SD card slot.
*It is releasable if a card is pushed once again.
*Don't mistake the
direction that the
micro SD card is
inserted.
① Open the battery cover. (Minus driver is used.)
SD card slot
21
<Before Use>
Connector
S.BUS connector (S.I/F)
When setting an S.BUS2 servo and telemetry
sensor, connect them both here.
*Do not connect the battery.
Connector for trainer function
When you use the trainer function, connect the
optional trainer cable between the transmitters for teacher and student.
*You can set the trainer function on the Trainer Function
screen in the System menu.
*A transmitter of anything but FMT-03 doesn't correspond to
this trainer system.
*An exclusive option trainer code is needed to use a trainer
system.
WARNING
Do not connect any other chargers except
the special charger to this charging connector.
SD card
Slot
S.BUS (S.I/F)
Connector
Battery
Connector
Connector for battery charger
This is the connector for charging the LiFe
battery FT2F2100BV2 that is installed in the
transmitter. Do not use any other chargers except the attached special charger corresponding to LiFe
battery.
Charge
Connector
Trainer
Connector
Teacher Student
Change
Remove the cover and connect trainer cable. Usually put on the cover.
Loading...
+ 47 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use