Furuno MU170C Installation Guide

Installation Manual

MU-170C for FAR-21x7

MULTI-PURPOSE LCD DISPLAY

IMPORTANT NOTICES...................................................................................................ii

SAFETY INSTRUCTIONS..............................................................................................iii

FOREWORD ...................................................................................................................v

SYSTEM CONFIGURATION ..........................................................................................vi

EQUIPMENT LISTS ......................................................................................................vii

1. MOUNTING .................................................................................................................1

1.1 Display Unit ................................................................................................................................ 1

1.2 Key Lock Function ..................................................................................................................... 4

2. WIRING .......................................................................................................................5

3. MAINTENANCE, TROUBLESHOOTING....................................................................6

3.1 Maintenance .............................................................................................................................. 6

3.2 Troubleshooting ......................................................................................................................... 7

4. MOUNTING OPTIONAL EQUIPMENT .......................................................................8

4.1 Hood........................................................................................................................................... 8

4.2 Handgrip.....................................................................................................................................9

4.3 Coupling Pedestal .................................................................................................................... 10

5. PARTS LOCATION ...................................................................................................12

SPECIFICATIONS..................................................................................................... SP-1

PACKING LISTS .........................................................................................................A-1

OUTLINE DRAWINGS ................................................................................................ D-1

INTERCONNECTION DIAGRAM................................................................................ S-1

Complies with IMO
MSC.192(79)

i

www.furuno.co.jp

IMPORTANT NOTICE

General

• The operator of this equipment must read and follow the descriptions in this manual.

Wrong operation or maintenance can cancel the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the

screens you see on your display. The screens you see depend on your system
configuration and equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by

FURUNO will cancel the warranty.

• All brand and product names are trademarks, registered trademarks or service marks of

their respective holders.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For
disposal in the USA, see the homepage of the Electronics Industries Alliance
(http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery(ies), see
the chapter on Maintenance. Follow the instructions below if a battery(ies) is used.

In the European Union

The crossed-out trash can symbol indicates that all types of
batteries must not be discarded in standard trash, or at a trash
site. Take the used batteries to a battery collection site
according to your national legislation and the Batteries Directive
2006/66/EU.

Cd

In the USA

The Mobius loop symbol (three chasing arrows) indicates that
Ni-Cd and lead-acid rechargeable batteries must be recycled.
Take the used batteries to a battery collection site according to
local laws.

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols
can increase when the other countries make their own recycling symbols in the future.

Ni-Cd Pb

ii

SAFETY INSTRUCTIONS

The operator and installer must read the applicable safety instructions before attempting to
install or operate the equipment.

Indicates a potentially hazardous situation which, if not avoided,

WARNING

CAUTION

Warning, Caution

could result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
can result in minor or moderate injury.

Prohibitive Action

Mandatory Action

Safety Instructions for the Operator

WARNING

Do not open the equipment.

Only qualified personnel
should work inside
the equipment.

Do not disassemble or modify the
equipment.

Fire, electrical shock or serious injury can
result.

Use the proper fuse and power cable.

Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.

Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.

CAUTION

Do not connect/disconnect the signal
cable while turning the power on.

The unit may be damaged.

A warning label is attached to the
equipment. Do not remove the label.
If the label is missing or damaged,
contact a FURUNO agent or dealer.

WARNING

To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.

Name: W arning Label (1)
T ype: 86-003-1011-1
Code No.: 100-236-231

Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.

Do not place any object near the
exhaust or intake vent.

Fire may result.

iii

Safety Instructions for the Installer

WARNING

Do not open the cover
unless totally familiar with
electrical circuits and
service manual.

Improper handling can result
in electrical shock.

Turn off the power at the switchboard
before beginning the installation.

Fire or electrical shock can result if the
power is left on.

Do not install the equipment where it
may get wet from rain or water splash.

Water in the equipment can result in fire,
electrical shock or damage to the
equipment.

CAUTION

Observe the following compass safe
distances to prevent interference to a
magnetic compass:

Standard Steering
compass compass

LCD Monitor MU-170C

Remote Controller

RMC-200

When lifting the display unit, hold it
together with the hard cover.

Grasping by the hard cover alone may
allow the display unit to fall, resulting in
possible bodily injury or damage to the
equipment.

0.5 m 0.3 m

0.3 m 0.3 m

iv

FOREWORD

A Word to the Owner of the MU-170C for FAR-21x7 Series

FURUNO Electric Company thanks you for purchasing the MU-170C for FAR-21x7 Series
17" Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name
has become synonymous with quality and reliability.

For 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality and
reliability throughout the world. This dedication to excellence is furthered by our extensive
global network of agents and dealers.

Your equipment is designed and constructed to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless properly
installed and maintained. Please carefully read and follow the operation, installation and
maintenance procedures set forth in this manual.

We would appreciate feedback from you, the end-user, about whether we are achieving our
purposes.

Thank you for considering and purchasing FURUNO.

Features

• High resolution display of 1280 x 1024 dot (SXGA)

• Brightness of 1000 cd/m

viewing day and night

2

(maximum) and 2 cd/m2 or less (minimum) for comfortable

• Landscape orientation

• Picture-in-picture function

• Complies with IMO MSC.192(79)

Note: This monitor meets the IMO requirements for CAT 2 vessels. Set up for CAT 2 in the
installation menu on the radar.

Category Sticker

Check the appropriate box on the sticker which is pre-attached on the processor unit,
according to your radar’s specification. Refer to the table shown below to confirm your
category.

Category Radar type ANT. rotation speed

CAT2

CAT2H

FR-2117/BB, FAR-2127/BB,

FAR-2137S

FAR-2117/BB, FAR-2127/BB,

FAR-2137S/BB

Normal speed

HSC

v

SYSTEM CONFIGURATION

12-24 VDC

DVI

This monitor accepts only DVI input. Do not connect to other types of input terminals.

Connectable equipment

Equipment

FAR-21x7 series SXGA DVI

Resolution Signal

FAR-21X7 series, etc.

vi

EQUIPMENT LISTS

Standard supply

Name Type Code No. Qty Remarks

Display Unit MU-170C - 1 w/hard cover

Remote Controller Set RMC-200 000-012-629 1 set

Spare Parts*

Installation Materials*

Accessories*

*: See packing list in this manual.

SP19-00401 001-416-700

CP19-00500 000-012-654

FP19-01001 001-416-740

1 set

1 set

1 set

Optional supply

Name Type Code No. Qty Remarks

1 Cable length: 5 m

1 Cable length: 10 m

1 Cable length: 5 m

1 set See page 3.

1 set

1 set

1 set

Cable Assy

Bracket kit
for Monitor

Remote
Controller
Set

Hood Kit

Handgrip
Assy.

Coupling
Pedestal Kit

3COX-2P-6C 5M 000-146-500

3COX-2P-6C 10M 000-146-501

DVI-D/D SINGLELINK5M 000-149-054

MU-170C Hanger 000-153-819

RMC-200 000-012-629 1 set

FP03-11200 001-011-880

FP03-09840 008-535-570

OP03-199 001-011-890

vii

1. MOUNTING

Refer to the outline drawing of this manual for mounting dimensions.

Note: The face of the LCD monitor is made of glass. Handle it with care.

1.1 Display Unit

The display unit may be mounted on a desktop (optional bracket kit required) or flush
mounted in a panel.

When selecting a mounting location, keep in mind the following points:

• Locate the unit out of direct sunlight.

• The unit weighs 7.5 kg (flush mounting) or 12.9 kg (desktop mounting). Be sure the

mounting location is strong enough to support the weight of the unit.

• Select a location where the display can be easily viewed and the controls can be easily

operated.

• Leave sufficient space around the unit for servicing and maintenance. See the outline

drawing for minimum service clearance.

• Locate the unit away from areas subject to water splash and rain.

1

Flush mounting

See the outline drawing of this manual for mounting dimensions.

CAUTION

Hold the hard cover and display unit
together when lifting the display unit.

The display unit may fall out if only the
hard cover is held.

1. Remove the hard cover and four cosmetic caps from the unit.

2. Using the paper template supplied, make a cutout in the mounting location.

3. Set the display unit to the cutout, and fasten it with four self-tapping screws (5x40,
supplied as accessories).

Note: Hex head bolts may also be used to fasten the display unit. However, their

lengths must project 10 mm from the wall.

Waterproofing: IP56, CFR46

Cosmetic cap

30

Flush mounting

4. Attach the cosmetic caps and the hard cover to the display unit.

98

Waterproofing: IP20

Minimum: 50

2

Desktop mounting

The display unit can be mounted on a desktop, using the optional bracket kit
(Type: MU-170C Hanger, Code No.: 000-153-819).

Contents of bracket kit

Name Qty

Hanger L 1
Hanger R 1
Pole 1
Hole plug 2
Hex bolt (M10x30) 2
Flat washer (M10) 2
Spring washer (M10) 2
Hex bolt (M5x25) 4
Flat washer (M5) 4

1. Assemble two hangers and pole with two hex bolts (M10x30), spring washers and flat
washers, and cover holes for hex bolts with the hole plugs.

2. Fix the above assembly to the mounting location with four hex bolts (M10, dockyard
supply).

Note: Do not mount the unit where the

exhaust or intake vent may be
obstructed.

3. Remove the hard cover and four cosmetic
caps from the unit.

4. Set the display unit to the assembled
hanger, and fasten it with four hex bolts (M5x25), spring washers and flat washers.

5. Attach the cosmetic caps and the hard cover to the display unit.

Spring washer (M5) 4

Intake vent

Exhaust vent

Display unit (rear view)

Hanger L

M10 bolts for fixing
(Dockyard supply)

Pole

Hex bolt (M5x25)

Spring washer (M5)

Flat washer (M5)

To remove this cosmetic cap,
insert fingernail in groove.

Desktop mounting

Hanger R

Flat washer (M10)

Spring washer (M10)

Hex bolt
(M10x30)

Hole plug

3

1.2 Key Lock Function

The key lock function re-sets the monitor functions to meet the monitor requirements for
CAT 2 IMO vessels. To activate the key lock function, turn on the power while pressing the
PIP key for more than five seconds.

4

2. WIRING

Connect external equipment to the MU-170C by referring to the drawing below, the table on
the next page and the interconnection diagram in this manual.

Note 1: The MU-170C does not have a “hot plug” function. Therefore, when the power
switch of the MU-170C and the equipment connected to it are on, do not connect or
disconnect the interconnection cable to prevent damage to equipment.
Note 2: This monitor accepts only DVI input. Do not connect to other types of input
terminals.

( )

(+)

Fuse

Blue

Red

Port

Name

TB-1

DVI-D

Grounding

TB-1

14AWG-2C-PVC *5M*

(Supplied)

Ground terminal

DVI-D

DVI-D/D SINGLELINK5M

(Option)

FAR-21X7 series

Display unit (bottom view)

Port, cable and connectable equipment

Used cable

Name Type Code No.

Power

cable

DVI

Cable

14AWG-2C-PVC
*5M*

DVI-D/D
SINGLELINK5M

000-154-337 Standard Power source

000-149-054 Option

Standard/

Option

12-24 VDC

Connectable

Equipment

FAR-21X7 series

Fasten a ground wire (dockyard supply) and the gray crimp-on lug of the power cable to the
ground terminal together. The length of the ground wire should be as short as possible.

Note: Use a “closed-type” lug (

“open-type” lug (

).

) to make the ground connection. Do not use an

5

3. MAINTENANCE, TROUBLESHOOTING

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment.

Only qualified personnel
should work inside the
equipment.

3.1 Maintenance

Routine maintenance

Regular maintenance is important for good performance. Check the following on a regular
basis to keep the equipment in good operating condition.

• Check that the connectors at the bottom of the display unit are tightly fastened.

• Check the ground wire and ground terminal for rust. Clean if necessary. Confirm that the

ground wire is tightly fastened.

• Remove dust and dirt from the display unit and LCD with a dry, soft cloth. Do not use

chemical cleaners to clean any part of the display unit – they can remove paint and
markings.

• Wipe the LCD carefully to prevent scratching, using tissue paper and an LCD cleaner.

To remove dirt or salt deposits, use an LCD cleaner, wiping slowly with tissue paper so
as to dissolve the dirt or salt. Change paper frequently so the salt or dirt will not scratch
the LCD. Do not use solvents such as thinner, acetone or benzene for cleaning.

• Clean the filter at the intake vent regularly. To remove the filter, grasp the intake vent

with fingers and pull forward. Use an air blower to remove dust and dirt from the filter. If
it is particularly dirty, wash it in water or mild detergent and then let it dry. When
reattaching the filter, be sure the filters are correctly set to the holes for the intake vent.

Intake vent

Display unit, rear view

6

Fuse replacement

The fuse in the fuse holder protects the equipment from internal fault. If the fuse blows, find
the cause before replacing it. If the fuse blows again after replacement, request service.

WARNING

Ship’s power source Rating of fuse

Use the proper fuse.

Use of a wrong fuse can cause fire or
damage to the equipment.

12 VDC 10 A

24 VDC 5 A

LCD replacement

The life of the LCD is about 40,000 hours. When the brilliance cannot be raised sufficiently,
replace the LCD.

3.2 Troubleshooting

The table below provides troubleshooting procedures to use when no picture appears. If
you cannot restore the picture, do not attempt to check inside the equipment – there are no
user serviceable parts inside. Refer any work to a qualified technician.

Troubleshooting table

Reason for no picture Remedy

Ship’s battery voltage too high. Check battery voltage.

Fuse has blown. Replace fuse.

Cable between MU-170C and external
equipment has loosened.

Power cable has loosened from the
terminal board.

Refasten cable.

Refasten cable.

7

4. MOUNTING OPTIONAL

EQUIPMENT

4.1 Hood

The hood (Type: FP03-11200, Code No.: 001-011-880) functions to shade the screen in
bright sunlight.

Contents of hood kit

Name Type Code No. Qty

Hood FP03-11201 001-011-900 1

Fixing plate 19-027-2002 100-337-700-10 4

Thumbscrew M4x10 000-862-543 4

Pan head screw M5x20 000-163-181-10 4

1. Remove four cosmetic caps from the unit.

2. Desktop mounting:

1) Remove two hex bolts, spring washers and flat washers from the hangers.

2) Set four fixing plates to four fixing holes on the display unit.

3) Attach the fixing plates with four pan head screws.
Flush mounting:
Fasten the display unit to the mounting location with four fixing plates and four
self-tapping screws.

Pan head screw
(M5x20)

Fixing plate

Fixing hole
for display unit

Fixing plate

3. Set the hood to the display unit, locating it outside the fixing plates.

4. Fasten the hood to the fixing plates with four thumbscrews from the outside of the hood.

8

4.2 Handgrip

The optional handgrip assy. (Type: FP03-09840, Code No.: 008-535-570) is available for
the desktop mount display unit.

Contents of handgrip assy.

Name Type Code No. Qty

Handgrip 14-002-1125-2 840-211-252 2

Oval countersunk head screw M6x20 000-163-677-10 4

Rosette washer M6 000-864-910 4

Wave washer WW-6 000-864-350 4

1. Remove four plastic rivets from the hangers.

Hanger

Plastic rivet

Hanger

2. Attach two handgrips to the hangers with four oval countersunk head screws, rosette
washers and wave washers.

Wave washer

Rosette washer

Oval countersunk
head screw

Handgrip

Handgrip

9

4.3 Coupling Pedestal

The optional coupling pedestal kit (Type: OP03-199, Code No.: 001-011-890) is available to
integrate the display unit with the optional bracket kit and the control unit (RCU-014).

Contents of coupling pedestal kit

Name Type Code No. Qty Remarks

Coupling plate assy. OP03-199-1 001-011-940 1 With coupling fixture

Washer head screw M4x20 000-163-195-10 2

Washer head screw M4x12 000-163-192-10 4

1. Set the coupling plate assy. on the mounting location.

2. Attach the coupling fixture to the bottom of the control unit (RCU-014) with four washer
head screws (M4x12).

Control unit (RCU-014)

Hook Coupling fixture

Coupling fixture

3. Set the control unit with the coupling fixture to the coupling plate assy. so that the
coupling fixture hooks on the clamp of the coupling plate assy.

Set display unit

Fixing hole

Set control unit here.

with bracket kit here.

Clamp

Coupling plate assy.

4. Fix the control unit to the coupling plate assy. with two washer head screws (M4x20).

Fix control unit with two washer head screws (M4x20).

Fixing control unit

10

5. Set the display unit with the bracket kit to the coupling plate assy. so that four fixing
holes of the hangers match those on the coupling plate assy.

6. Fasten the bracket kit and the coupling plate assy. to the mounting location with four
M10 bolts (Length: more than 80 mm, dockyard supply) and M10 nuts (dockyard
supply).

Display unit

Fasten bracket kit and coupling plate assy.
to mounting location with four M10 bolts
and M10 nuts.

Fixing display unit

11

5. PARTS LOCATION

FURUNO Model

Unit

ELECTRICAL PARTS LIST

2008/11

SYMBOL PRINTED CIRCUIT BOARD/ REMARKS

DISPLAY UNIT MU-170C

A/D Board 890ADJF170AP
INVERTER Board 891LIJF170AP
PANEL Board 890KPJF170AP
POWER Board 891POJF170AP

LCD Panel 856AU1745JF1

Display Unit MU-170C

POWER Board
(891POJF170AP)

INVERTER Board

(891LIJF170AP)
(beneath plate)

PANEL Board
(890KPJF170AP)

12

A/D Board
(890ADJF170AP)

LCD Panel

(856AU1745JF1)

13

FURUNO

MU-170C for FAR-2xx7 Series

SPECIFICATIONS OF MULTI-PURPOSE LCD DISPLAY

MU-170C for FAR-21x7 Series

1 GENERAL

1.1 Display 17-inch SXGA color TFT-LCD, 338 x 270 mm

2

1.2 Brightness maximum: 1000 cd/m

1.3 Resolution 1280 x 1024 (SXGA)

1.4 Viewing angle up/down: 75°, left/right: 80°

1.5 Input signal

RGB ports 2 ports, VESA (VGA, SVGA, XGA, SXGA),

(0.7 Vp-p, Synchronization: TTL level)

DVI port 1 port, VESA (VGA, SVGA, XGA, SXGA)

VIDEO ports 3 ports, NTSC/PAL, 0.7 Vp-p (75 Ω)

2 POWER SUPPLY

, minimum: 2 cd/m2 or less

12-24 VDC: 6.0-3.0 A

3 ENVIRONMENTAL CONDITION

3.1 Ambient temperature

Display unit -15°C to +55°C

Remote controller +5°C to +35°C

3.2 Relative humidity 93% at +40°C

3.3 Waterproofing

Display unit IP56 (front panel), IP20 (rear panel)

Remote controller IPX0

3.4 Bearing vibration IEC 60945-4

3.5 EMC IEC 60945

4 COMPASS SAFE DISTANCE

Standard compass: 0.5 m

Steering compass: 0.3 m

5 COATING COLOR

N2.5 (not changed)

Refer to FAR-21x7 series specifications.

SP - 1 E20341S01A

1/1

A-1

CP19‑00500

1

1

1

1

19AX‑X‑9851

19AX‑X‑9851‑5

NAME OUTLINE Q'TYDESCRIPTION/CODE№

工事材料 INSTALLATIONMATERIALS

000‑154‑337‑00

14AWG‑2C‑PVC*5M*

POWERCABLE

図書 DOCUMENT

電源ｹｰﾌﾞﾙ

000‑156‑775‑0*

C22‑00503‑*

ﾌﾗｯｼｭﾏｳﾝﾄ型紙

FLUSHMOUNTINGTEMPLATE

000‑154‑137‑0*

C22‑00501‑*

ﾋｭｰｽﾞ変更願い

NOTICEFORFUSE

000‑153‑885‑1*

OMC‑20340‑*

取扱説明書

OPERATOR'SMANUAL

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。 なお、品質は変わりません。

TWOTYPESANDCODESMAYBELISTEDFORANITEM.THELOWERPRODUCTMAYBESHIPPEDINPLACEOF

THEUPPERPRODUCT.QUALITYISTHESAME.

MU‑170C

ＰＡＣＫＩＮＧ ＬＩＳＴ

1

000‑012‑653‑00

MU‑170C

1

RMC‑200

1

(*)

999‑999‑113‑00

19‑024‑1313‑0

1

100‑315‑270‑10

100‑292‑801‑10

14‑034‑2075‑1

1

000‑149‑069‑00

RMC‑200

SP19‑00401

1

001‑416‑700‑00

SP19‑00401

FP19‑01001

1

001‑416‑740‑00

FP19‑01001

NAME OUTLINE Q'TYDESCRIPTION/CODE№

ユニット UNIT

LCD表示器

MULTI‑PURPOSELCD

ﾘﾓｺﾝｾｯﾄ REMOTECONTROLLERSET

電池ｾｯﾄ(単3Ｘ2)

SIZEAABATTERY

ﾘﾓｺﾝﾊﾘﾏｰｸ

予備品 SPAREPARTS

STICKER

ﾘﾓｺﾝﾋﾞﾆﾙｹｰｽ

VINYLCASEFORREMOTE

ﾘﾓｺﾝｷｰﾕﾆｯﾄ

REMOTECONTROLLER

予備品

SPAREPARTS

付属品 ACCESSORIES

付属品

ACCESSORIES

（*）は、ﾀﾞﾐｰｺｰﾄﾞに付き、注文できません。

（*） THISCODECANNOTBE ORDERED.

（略図の寸法は、参考値です。DIMENSIONSINDRAWINGFORREFERE NC E ONLY.）

付属品表

A-2

ACCESSORIES

番号

NO.

1

名  称

+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ
SELF‑TAPPINGSCREW

NAME

MULTI‑PURPOSELCDDISPLAY

MU‑170C

略  図

OUTLINE

CODENO.
TYPE

DESCRIPTIONS

5X40SUS304

CODENO.

001‑416‑740
FP19‑01001

型名／規格

000‑150‑749

数量

Q'TY

19AX‑X‑9501

4

‑0

1/1

用途／備考

REMARKS

19AX‑X‑9501

ＦＵＲＵＮＯ ＥＬＥＣＴＲＩＣ ＣＯ ．，ＬＴＤ.

（略図の寸法は、参考値です。 DIMENSIONSINDRAWINGFORREFERENCEONLY.）

SHIPNO.

A-3

CODENO.
TYPE

SPAREPARTSLISTFOR USE

MULTI‑PURPOSELCDDISPLAY

MU‑170C

001‑416‑700
SP19‑00401

BOXNO.P

SETSPER
VESSEL

1/1

‑019AX‑X‑9301

ITEM
NO.

1

2

NAMEOF
PART

ﾋｭｰｽﾞ

ﾋｭｰｽﾞ

OUTLINE

DWG.NO.

OR

TYPENO.

10A125V

5A125V

QUANTITY REMARKS/CODENO.

WORKING

PER

PER
VES

SPARE

ﾀﾞﾐｰｺｰﾄﾞ

DUMMYCODEFUSE

999‑999‑111

ﾀﾞﾐｰｺｰﾄﾞ

DUMMYCODEFUSE

999‑999‑112

SET

13

13

MFR'SNAME

FURUNOELECTRICCO.,LTD.

（略図の寸法は、参考値です。DIMENSIONSINDRAWINGFORREFERENCEONLY.）

DWGNO.

19AX‑X‑9301

1/1

Y.Hatai

D-1

Y.Hatai

D-2

ECHO SOUNDER

Y.Hatai

S-1

SONAR

RADAR

PLOTTER

MU‑170C

17型カラーLCD表示器

相互結線図

MULTI‑PURPOSE LCD DISPLAY

ソナー

レーダー

プロッタ

43

魚群探知機

レーダー RADAR

TITLE

名称

INTERCONNECTION DIAGRAM

NAME

MULTI‑PURPOSE LCD DISPLAY

17型カラーLCD表示器

MU‑170C

*2

3COX‑2P‑6C,5/10m,φ8.5

*3*3

Dsub15P(mini)Dsub15P(mini)

9

8

7

6

5

4

RGB2

RGB1

123

RED

GREEN

GREEN

RED
123

BLUE

BLUE

NC

4

GND

GND

GND

GNDNCGND

678

5

GND

GND

GND

+5VVGA +5VVGA

9

11

10

NC

NC

VGACABLE VGACABLE

111514

10

121314

HSYNCN

SDA SDA

HSYNCN
13

12

VSYNCN

VSYNCN

*2

DVI‑D/D SINGLELINK5M

5m,φ7.1

P

*3

DVI‑D

*4

DVI‑D

VIDEO1

RCA METAL

123

Rx2‑

Rx2+

GND

VIN

15

SCL SCL

678

4

5

Rx4‑

Rx4+

Rx2 SHIELD

VIDEO2

*4

RCA METAL

P

9

10

11

12

13

NC

Rx1‑

Rx1+

Rx3‑

Rx3+

DDC SCL

DDC SDA

Rx1 SHIELD

GND

VIN

GND

VIN

VIDEO3

*4

RCA METAL

1514171619

HPD

DDC +5V

DDC GND

TB‑1

+

1

RED
アカ

P

RxO‑

‑

2

BLU
アオ

P

18

20

RxO+

Rx5‑

Rx0 SHIELD

242223

21

E.MIYOSHI

Oct.5,'05

CHECKED

DRAWN

TAKAHASHI.T

C2034‑C01‑A

APPROVED

DWG.No.

Rx5+

RxC+

RxC‑

RxC SHIELD

IV‑8sq.

*1

2

*2

*4

3COX‑2P‑6C,5/10m,φ8.5

3C2V OR 2.5C2V (75Ω),10m MAX.

*4

3C2V OR 2.5C2V (75Ω),10m MAX.

*4

14AWG‑2C‑PVC,5m,φ10

3C2V OR 2.5C2V (75Ω),10m MAX.*4

ECHO SOUNDER

SONAR

RADAR

PLOTTER

*4

*4

12‑24 VDC

魚群探知機

ソナー

レーダー

プロッタ

VIDEO RECORDER

CCD CAMERA

ビデオデッキ

CCDカメラ

VIDEO RECORDER

CCD CAMERA

ビデオデッキ

CCDカメラ

VIDEO RECORDER

CCD CAMERA

ビデオデッキ

CCDカメラ

1

注記

＊１）造船所手配

＊２）オプション

＊３）工場にて取付済み

A

B

C

＊４）ユーザー手配

NOTE

*1. SHIPYARD SUPPLY

*2. OPTION

*3. FITTED AT FACTORY.

*4. USER SUPPLY

Thepaperusedinthismanual

9‑52Ashihara‑cho,

Fax:

A:NOV

2008

.

Pub.No.

(

)

*

00017069610

**00017069610

*

Nishinomiya,662‑8580,JAPAN

Telephone: +81‑(0)798‑65‑2111

+81‑(0)798‑65‑4200

iselementalchlorinefree.

・FURUNOAuthorizedDistributor/Dealer

Allrightsreserved.

DAMI

MU‑170CIMO

PrintedinJapan

IME‑20341‑A

*00017069610**00017069610*

*00017069610*