MULTI-PURPOSE LCD DISPLAY
Back
MU-150C
SAFETY INSTRUCTIONS
Safety Instructions for the Operator
WARNING
Do not open the equipment.
Only qualified personnel
should work inside
the equipment.
Do not disassemble or modify the
equipment.
Fire, electrical shock or serious injury can
result.
Use the proper fuse.
Fuse rating is shown on the equipment.
Use of a wrong fuse can result in damage
to the equipment.
Immediately turn off the power at the
switchboard if the equipment is emitting
smoke or fire.
Safety Instructions for the Installer
WARNING
Do not open the cover
unless totally familiar with
electrical circuits and
service manual.
Improper handling can result
in electrical shock.
Turn off the power at the switchboard
before beginning the installation.
Fire or electrical shock can result if the
power is left on.
Do not install the equipment where it
may get wet from rain or water splash.
Water in the equipment can result in fire,
electrical shock or damage to the equipment.
Continued use of the equipment can cause
fire or electrical shock. Contact a FURUNO
agent for service.
CAUTION
A warning label is attached to the
equipment. Do not remove the label.
If the label is missing or damaged,
contact a FURUNO agent or dealer.
WARNING
To avoid electrical shock, do not
remove cover. No user-serviceable
parts inside.
About the TFT LCD
The TFT LCD is constructed using the
latest LCD techniques, and displays
99.99% of its pixels. The remaining 0.015%
of the pixels may drop out or blink, however this is not an indication of malfunction.
Name: Warning Label (2)
Type: 03-129-1001
Code No.: 100-236-741
CAUTION
Ground the equipment to
prevent mutual interference.
Observe the following compass safe
distances to prevent interference to a
magnetic compass:
Standard Steering
compass compass
MU-200C
Locate the MU-150C out of direct sunlight for optimum viewing.
When lifting the display unit, hold it
together with the cover.
Grasping by the cover alone may allow
the display unit to fall, resulting in
possible injury or damage to the equipment.
1.55 m 1.05m
i
TABLE OF CONTENTS
FOREWORD ........................................................................................................iii
SYSTEM CONFIGURATION................................................................................ iv
EQUIPMENT LISTS.............................................................................................. v
1 MOUNTING ...................................................................................................... 1
1.1 Display Unit.....................................................................................................................1
2 WIRING............................................................................................................. 7
2.1 Wiring External Equi pment..............................................................................................7
3 ADJUSTMENTS.............................................................................................10
3.1 Picture Adjustment ........................................................................................................11
3.2 RGB Adjustment............................................................................................................12
3.3 Brilliance Adjustment.....................................................................................................12
4 OPERATION................................................................................................... 13
5 MAINTENANCE, TROUBLESHOOTING.......................................................14
5.1 Maintenance..................................................................................................................14
5.2 Tr o ubleshooting.............................................................................................................15
APPENDIX
Modification for Switching from Landscape to Portrait Orientation ........AP-1
SPECIFICATIONS...........................................................................................SP-1
PACKING LISTS
OUTLINE DRAWINGS
INTERCONNECTION DIAGRAM
ii
FOREWORD
A Word to the Owner of the MU-150C
FURUNO Electric Company thanks you for purchasing the MU-150C 15” Multi-Purpose
LCD Display. We are confident you will discover why the FURUNO name has become
synonymous with quality and reliability.
For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for
quality and reliability throughout the world. This dedication to excellence is furthered by our
extensive global network of agents and dealers.
Your equipment is designed and constructed to meet the rigorous demands of the marine
environment. However, no machine can perform its intended function unless properly
installed and maintained. Please carefully read and follow the operation, installation and
maintenance procedures set fort h in this manual.
We would appreciate feedback from you, the end-user, about whether we are achieving our
purposes.
Thank you for considering and purchasing FURUNO.
Features
•
Main or remote display for radars, video sounders, sonars. Com patible equipment:
FR-1505 MK3 series, FR-1760DS, FCV-1200 series, FCV-1500 series, CH-250, CH-37,
CSH-23/73/83, GD/GP-280/380/680, etc.
•
High resolution display of 1024 x 768 dot (XGA), 640 x 480 dot (VGA)
•
Brightness of 180 cd/m
and night
•
Landscape or portrait orientation
•
Wide viewing angle of 160° for observation b y more than one person
2
(typical) and minimum 150 cd/m
2
for comfortable viewing day
iii
v
SYSTEM CONFIGURATION
RGB
24 VDC or
100 - 240 VAC
NMEA 0183
Connect able equipment
MU-150C Display Unit Type
Radar, Video Plotter,
Navigator, Video Sounder,
Scanning Sonar, etc.
Control unit of
Video Sounder
(e.g., FCV-1200 series)
Navigator (GPS, etc.)*
* = When using the FCV-1200 series or
CH-250, NMEA 0183 data may be output
to the MU-150C instead of the interface
unit.
Equipment
Landscape Portrait*
FR-1500 MK3 series Yes No
FCV-1200 series Yes Yes (Modification required)
FCV-1500 series No Yes (Modification required)
GD/GP-280/380/680 Yes No
CH-250 Yes No
CH-37 No Yes (Modification required)
CSH-23/73/83 No Yes
FR-1760DS No Yes (Modification required)
* = Display cannot be viewed with polarized sunglasses.
i
v
EQUIPMENT LISTS
Standard supply
Name Type Code No. Qty Remarks
Display Unit MU-150C − 1
Spare Parts *
Installation Materials *
Accessories *
Bracket *
SP10-02801 001-414-460
SP10-02802 001-414-970
CP10-04910 001-414-690
CP10-04920 001-414-700
FP10-02501 001-414-490
FP10-05401 001-402-540
FP10-02510 001-414-510 1 Including FP10-02511
1 set
1 set
1 set
1 For FCV-1500L
AC specification
DC specification
For DC
For AC
For AC (CP10-04901)
For DC (CP10-04902)
Option
Name Type Code No. Qty Remarks
Bracket *
Hood (Landscape)
Hood (Portrait)
* = See packing list at end of manual.
FP10-02510 001-414-510
FP10-02502 001-414-730
FP10-02503 001-414-750
1 Including FP10-02511
1
1
1 MOUNTING
Refer to the outline drawing at the end of the manual for mounting dimensions.
Note: The LCD is made of glass. Handle it with care.
1.1 Display Unit
The display unit may be flush mounted in a panel or on a desktop, using the optional
bracket. Display tilt can be chosen from 9° or 20°, by the location of the mounting plate.
When selecting a mounting location, keep in mind the following points:
• Locate the unit out of direct sunlight.
• Select a location where the display can be easily viewed and the controls can be easily
operated.
• Leave sufficient space around the unit for servicing and maintenance. See the outline
drawing for recommended servicing space.
• The unit weighs 35.3 lbs (16 kg). Be sure the mounting location is strong enough to
support the weight of the unit.
• Locate the unit away from areas subject to water splash and rain.
Flush mounting
See the outline drawing at the end of the manual for mounting dimensions.
CAUTION
Hold the cover and display unit
together when lifting the display unit.
The display unit may fall if only the cover
is held.
1. Using the paper template supplied in the installation materials, make a cutout in the
mounting location. (Modification of the LCD may be necessary depending on equipment
used. See “Modification for Switching from Landscape to Portrait Orientation” in the
Appendix for details.)
2. Pull the display unit cover toward you to detach it.
1
See Note 2.
Cover Display Unit
Display unit and cover
3. Fasten the display unit to the mounting location with six tapping screws (5X30).
Note 1: Hex head bolts may also be used to fasten the display unit. However, their
length must be at least 30 mm.
Note 2: Use M5 bolt or tapping screw (nominal diameter: M5), although the size of the
mounting holes in the display unit is M8.
384 ±0.5
366 ±1
15 ±0.5
0.5
±
259
1
±
315
0.5
±
333
15
±
0.5
333 ±0.5
315 ±1
259 ±0.5
366
±
1
384
±
0.5
82
45
Mounting dimensions for landscape orientation Mounting dimensions for portrait orientation
100
Unit: mm
45
82
100
Unit: mm
Mounting dimensions
4. Reattach the cover.
5. For the portrait model only, attach the FURUNO logo seal (supplied in the accessories)
at the top left corner. Remove the logo seal from the bottom left corner.
2
Desktop mounting
The display unit can be mounted on a desktop, using the optional bracket (Type:
FP10-02510, Code No.: 001-414-510).
1. Fasten the mounting base (lower) to the mounting location with four sets of hex head
bolts, spring washers, flat washers and nuts.
Hex Head Bolt
Spring Washer
Flat Washer
Nut
FRONT
Mounting base (lower)
2. Fasten the bracket and mounting plate to the mounting base (upper) with 12 hex head
bolts. Fasten the mounting plate at the rear for 9° tilt, or at the front for 20° tilt.
Hanger
Mounting Plate
Mounting Base
(upper)
Mounting Plate
Mounting Base
(upper)
REAR
9 degree TILT 20 degree TILT
Hanger
FRONT
Fastening bracket and mounting plate t o mounting base (upper)
3
3. Loosely s c r ew six screw s (M5X15) into t he holes at the rear of the display unit. S et t he
screw s on the display unit to the holes on the bracket and then tighten the screw s . (Note
that the di s play unit m ay also be mounted i n portrait orientation.)
Fastening the front panel
4. Fasten the power cable (local s upply in case of AC pow er ) , cable from the control and
operati on s ec tions of ext er nal equipme nt and ground wire (local s upply) at the r ear of
the MU-150C. For use of the cable type 06S4078 (from a c ontrol section), cut off the
connector’s rubber cover and remove the fixing metal to enabl e c onnec tion.
Cable from operation section
NMEA
MJ-A10SPF0002
DISPLAY
UNIT
Cable from control section
06S4078 *5m*
Power Cable
Ground Wire
Connecti on of cables at the rear of the di s play unit
4
5. Grease the two hex head bolts for fastening the display unit to the mounting base
(lower).
6. Fasten the display unit to the mounting base (lower) with the two hex head bolts
greased at step 5.
Hex Head Bolt
Fastening the mounting base (lower) to the display unit
7. For portrait orientation, attach logo (supplied) at upper left hand corner.
5
1.1.1 Hood (option)
A hood (portrait or landscape) is optionally available. Attach it to the display unit with Velcro
tape as shown below.
1. Attach nine sets of Velcro tape to the display unit at the locations shown below, in as
straight as possible.
Attach
in line.
Display unit, how to attach Velcro tapes
2. Attach the hood to the display unit.
Attach
in line.
6
2 WIRING
2.1 Wiring External Equipment
Connect ext er nal equipment to the M U- 150C by refer r ing to the draw ings in this section. A
cable with connector at both ends is pro vided to connect equipment.
Genera l-purpose monitor
To use the MU-150C as a gener al-purpose monitor, connect equipment w ith a mini D-SUB
15P connec tor. In this case do not connect a navigator to the NMEA port. Nav data is output
through the D- S UB 25P connector.
CH-37: DISPLAY
CH-250: INTERFACE UNIT RGB OUT
FCV-1200 Series: INTERFACE UNIT RGB OUT
FCV-1500 Series: DISPLAY UNIT DISPLAY
Mini D-SUB
15P
GP/GD-280/380/680: DISPLAY UNIT EXT VIDEO
FR-1500 MK3 Series: Connector on RGB BUFFER
board in display unit
FR-1760DS: Connector on RGB BUFFER
board in display unit
24 VDC
or 100-240 VAC
Ground
Terminal
Display unit, rear vi ew, wiring using general-purpose cables
Note: When connecting a general-pur pose mon itor, use the following c able or the
equivalent:
Mini D-s ub 15P : EVNPS05-50 ft, male-male, (max. 15 m)
Manufacturer: BlackBox Japan
7
Conn ecting FCV-1200 series and CH-250
FCV-1200 Series: CONTROL UNIT
CONT
CH-250: CONTROL UNIT
REM CONT
FCV-1200 Series:
PROCESSOR UNIT CN1
CH-250: TRANSCEIVER UNIT
DATA/VIDEO OUT
24 VDC
or 100-240 VAC
Ground
Terminal
Navigator, etc.
MJ-A10SPF0002-015
06S4078
Using the cables designated below (or equivale nt) to connect the FCV-1200 series or
CH-250 mak es their int er face unit of the FCV-1200 seri es and CH-250 unnecessary. The
mini D-S UB 15 P connector cannot be used to connect the FCV-1200 series and CH - 250.
Notes on wiring
•
Armor
•
Display unit, rear vi ew, wiring using specialty cables
For AC specification, s older connector S RCN6A13- 3S ( s upplied in installation mat er ials)
to the power cable (DPYC-1.5 (Jap an Industrial Standard) or equivalent) .
Sheath
Armor
Armor
How to solder connector S RCN6A13-3S; sectional v iew of cable DPY C-1.5
The cover of t he D- s ub connector of the cable 0 6S4078 may be r em oved to pass the
cable through tubing, bulkhead, et c . Use vinyl tape to bind connector wiring and rubbe r
4-6 cm
3mm
Solder Side
Screw
Clamp
Connector Housing
Soldering connector SRCN6A13-3S
Tighten
set screw
21
3
Connect to
"1" and "2".
1: AC (L: Live line)
2: AC(N: Neutral line)
Armor
Conductor
S = 1.5 mm
f
= 1.56 mm
Sectional view of cable DPYC-1.5
cover. T his allow s the cable to be passed through a hole having a diam eter of 30 mm.
2
8
• Cable 06S4078 is of waterproof construction, however, the MU-150C is not waterproof
(specification IPX0). Therefore, remove rubber cover and fixing metal from the display
side of the cable.
Remove fixing metal.
Remove rubber cover.
D-sub connector
9
3 ADJUSTMENTS
Controls f or adjustment of the picture ar e provided on the r ear of the di s play uni t. Open the
small cover to access the controls.
12
3
GND
POWER
2A
S1 S2 S3 S4
J16 J17 J18
13
13
13
100-240 VAC
50-60 Hz
R1
J16
R2
R3
J17
J18
R1
R2
R3
EXTBRILL
BRILL
BRTP
R
G
B
S1
S2
S3
S4
SEL
UP
DOWN
RESET
CONT
DATA/VIDEO IN
NMEA
Rear panel (AC type)
10
3.1 Picture Adjustment
Contrast an d picture are a djusted with
[S1]: O pens m enu; selects menu item s.
[S2]: Increas e s settin g .
[S3]: Decreases setting.
[S4]: Initialize s setting.
Note: Though “EXIT” is pri nted on the CONE Board (10P6877), the function of S4 swi tch is
“RESET.”
[S1]
Brilliance
(Not used.)
[S1]
Contrast
[S1]
Size (horizontal size for landscape type, vertical size
for portrait type)
[S1]
Geometry
[S1]
Center (vertical position for landscape type, horizontal
position for portrait type)
[S1]
Center (horizontal position for landscape type, vertical
position for portrait type)
[S1]
ALL RESET
Press Reset Key
Over 2Seconds.
[S1]
Press [S4] to
Initialize settings
About the picture adjustment bu ttons
•
The [S2] and [S3] buttons may be press ed and held down to increase/decrease set ting
more rapidl y.
•
The [S4] button can i nitialize settings individually or all at once. Press it at aft er
adjustment of a specific setti ng, or at the “ALL RESET” screen to i niti alize all picture
adjustment s ettings.
•
The adjus tment display disappears if there i s no adjustment within five seconds.
11
3.2 RGB Adjustment
Color may be adjusted with the following potentiometers. Turn the potentiometers c lockwi s e
to increase c olor.
Model Potentiometer Setting
FCV-1200 Series , CH-250,
FR-1760DS
GD/GP-280/380/680, F CV-1500
Series, CH- 37, CSH23/73/83,
FR-1500 MK3 Series
R1: Red
R2: Green
R3: Blue
Default setting
Fully clockwise
3.3 Brilliance Adjustment
Brilliance can be adjust ed from the co ntrol unit of the FCV-1200 series or CH-250 by setti ng
jumper bloc k J 17 as below.
J17: Brilliance control circuit selection
1-2: Brilliance is adjusted from t he M U- 150C (default s etting)
2-3: Brilliance is adjusted from t he c ontrol unit of the FCV-1200 series or CH-250
Note: Do not change the set ting of the J16 or J 18. T he default setting for both i s “ 1-2” .
S1 S2 S3 S4
R1
J16
J16 J17 J18
13
13
R2
13
R3
Jumper blocks
J17
J18
R1
R2
R3
EXTBRILL
BRILL
BRTP
R
G
B
S1
S2
S3
S4
SEL
UP
DOWN
RESET
12
4 OPERATION
FURUNO
BRILLIANCE ControlLED
POWER
Switch
Display unit
POWER switch: Turns the power on/off. The LED lamp lights in green when the unit
is turned on and goes off when the unit is turned off.
To turn the MU-150C on and off from the control unit of a video
sounder such as the FCV-1200 series, turn on the POWER switch
of the MU-150C. Note that with the MU-150C turned on and the
FCV-1200 turned off the LED on the MU-150C lights in red. This
means that weak current is flowing to the MU-150C. To turn off the
power completely, turn off the MU-150C.
BRILLIANCE control: Adjusts display brilliance. In some instances brilliance is controlled
from the equipment connected (for example, FCV-1200 series).
LED: Shows display status:
Green: Display on
Red: Power save
13
5 MAINTENANCE,
TROUBLESHOOTING
WARNING
ELECTRICAL SHOCK HAZARD
Do not open the equipment.
Only qualified personnel
should work inside the
equipment.
5.1 Maintenance
Routine maintenance
Regular maintenance is important for good perf or mance. Check the follow ing on a regular
basis to keep t he equipment in good operating condit ion.
• Check that the connectors at the rear of the display uni t are tightly fastened.
• Check the ground wire and gr ound terminal for rust. Clean if necess ar y. Confirm that the
ground wire is tightly fastened.
• Remove dust and dirt f r om the display unit and LCD with a dry, soft cloth. Do not use
chemical cleaners to cl ean any part of the displ ay unit – they can remo ve p aint and
markings.
• Wipe the LCD carefully o prevent scratching, usi ng tissue paper and an LCD cleaner. To
remove dirt or s alt deposits, use an LCD cleaner, wi ping slowly wit h tissue paper so as
to dissolve the dirt or salt. Change paper frequently so the salt or dirt will not scratch the
LCD. Do not use s olvents s uch as thinner, acet one or benzen e for cleaning.
Fuse replacement
The 1.5 A 250 V fuse (AC type) or 3A 125V fuse (DC type) on the rear panel protects t he
equipment from internal fault and overcurrent. If the fuse blows, find the c aus e before
replacing it. If the fuse blows again after repl ac em ent, request service.
WARNING
Use the proper fuse.
Use of a wrong fuse can cause fire or
damage to the equipment.
14
5.2 Troubleshooting
The table below provides troubleshooting procedures to use when no picture appears. If
you cannot restore the picture, do not attempt to check inside the equipment – there are no
user serviceable parts inside. Refer any work to a qualified technician.
Troubleshooting table
Reason for no picture Remedy
Battery voltage too high. Check battery voltage.
Fuse has blown. Replace fuse.
Cable between MU-150C and external
equipment has loosened.
Power cable has loosened. Refasten cable.
Refasten cable.
15
A
APPENDIX Modification for Switching from Landscape to Portrait Orientation
To use the MU-150C for portrait w ith the CH-37, FCV-1200 series, FCV-1500 series or
FR-1760DS, the LCD assem bly must be turned 180°.
1. Place t he display unit on a workbench with the LCD side down. I t is recommended to
place the uni t on cushioning m aterial s o as not to place press ure on knob.
2. Unfasten t he items marked wit h white arrows in the f igure below to remove the cover for
the power s ec tion and connectors: 10 screws, four spacer s for connectors and two nuts
of waterpr oof connectors . T his gives access to t he CONE Board (10P6877) and power
assy.
Display unit, rear vi ew
3. Remove the 14 s c r ews marked with gray ar r ows in the figure above.
P-1
A
4. Referring to the arrows in the figure below for location, disconnect the connector and
four power switch tag terminals and release cable from CK clamp.
Note: When disconnecting the tag terminals, pull them by the metal part of the terminal.
Do not disconnect by pulling the cable – cables may become separated from the
terminal.
Power assy.
P-2
A
5. Unfasten t he eight scr ews marked with the arrows in the figur e below.
Display unit, rear vi ew
6. Release the cable from the clamp marked wit h the gray ar r ow in the figur e above.
7. Turn the LCD assem bly 180°.
POWER chassis
Display unit, rear vi ew
8. Fasten scr ews unfastened at step 5. ( Torque: 0. 39 ±0.04 Nm; 4 ±0. 4 k gm )
9. Turn the pow er c has s is 180° counterclockwise, making sure n o load is pl ac ed on the
cable at the c enter of the power chassis when turning. When reassembl ing the display
unit to “landscape,” tur n the power chas s is 180° clockwise. The tape for fixing the cable
from the LCD may peel of f if the power c has s is is turned t wice or more in the same
direction.
10. Fasten the cable with the cl amp m ar k ed with the gray arrow i n s tep 6.
P-3
A
11. Fasten cables with the clamps marked with the white arrows in the figure below.
Connect the power connector to J1 on the pcb 10P3879 as follows: 1, Brown; 3, Orange;
4, Purple, 6, White.
Location of power switch and pcb 10P3879
12. Fix the rear cover with 14 screws (M4 x 8). (Torque 1.47 ±0.15 Nm; 15 ±1.5 kgm)
13. Temporarily fasten the cover for the power section and connectors with 10 screws
(M3 x 8).
14. Fix four spacers for connectors. (Torque: 0.39 ±0.04 Nm; 4 ±0.4 kgm)
15. Temporarily fasten the cover for the power section and connectors with six screws
(M3 x 8). (Torque: 0.78 ±0.08 Nm; 8 ±0.8 kgm)
16. Fasten two waterproofing nuts. (Torque: 0.76 ±0.02 Nm; 7.8 ±0.2 kgm)
17. Fasten the cover near the power section and connectors with remaining four screws.
(Torque: 0.78 ±0.08 Nm; 8 ±0.8 kgm)
18. Attach the FURUNO logo (supplied) at the cavity in the upper left corner of the display
unit.
P-4
SPECIFICATIONS OF MULTI-PURPOSE LCD DISPLAY
MU-150C
1 GENERAL
1.1 Display 15.0 inch color LCD, 304.1 x 228.1 mm
1.2 Brightness 180 cd/m2 typical, 150 cd/m2 minimum
1.3 Resolution VGA (640 x 480), XGA (1024 x 768)
1.4 Viewing Angle 160° (left/right: 80°, up/down: 80°)
1.5 Input Signal RGB: 0.7 Vp-p to 3.0 Vp-p, Synchronization: TTL level
2 POWER SUPPLY
2.1 Rated Voltage 100-240 VAC: 0.7-0.4 A, 1 phase, 50-60 Hz
24 VDC, 1.4 A
3 ENVIRONMENTAL CONDITION
3.1 Ambient Temperature Operation: 0°C to +50°C, Storage: -20°C to +60°C
3.2 Relative Humidity 95% at 40°C
3.3 Waterproofing IPX0
3.4 Vibration IEC 60945
4 COATING COLOR
4.1 Main Unit N3.0
SP - 1 E2025S01B
This page is intentionally left blank .
ＰＡＣＫＩＮＧ ＬＩＳＴ
C2025-Z01-E
A - 1
ＰＡＣＫＩＮＧ ＬＩＳＴ
ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ
MU-150C-H-DC-CS
MU-150C-H-DC-CS
MU-150C-H-DC-CSMU-150C-H-DC-CS
10CQ-X-9851 -5
1/1
N A M E
ユニット
ユニット UNIT
ユニットユニット
15型ｶﾗｰLCD表示器
MULTI-PURPOSE LCD DISPLAY
予備品
予備品 SPARE PARTS
予備品予備品
ﾋｭｰｽﾞ
FUSE
付属品
付属品 ACCESSORIES
付属品付属品
ﾛｺﾞｼｰﾄ
LOGO SEAL
工事材料
工事材料 INSTALLATION MATERIALS
工事材料工事材料
ｹｰﾌﾞﾙ組品MJ
CABLE ASSY.
その他工材
その他工材 OTHER INSTALLATION MATERIALS
その他工材その他工材
装備用型紙
UNIT
UNITUNIT
SPARE PARTS SP10-02801
SPARE PARTSSPARE PARTS
ACCESSORIES FP10-02501
ACCESSORIESACCESSORIES
INSTALLATION MATERIALS CP10-04902
INSTALLATION MATERIALSINSTALLATION MATERIALS
OTHER INSTALLATION MATERIALS
OTHER INSTALLATION MATERIALSOTHER INSTALLATION MATERIALS
O U T L I N E
DESCRIPTION/CODE №
MU-150C-H-DC
000-012-618
FGMB 3A 125V
000-104-909
10-075-1052-0
100-294-900
MJ-A3SPF0020-050Z
000-145-882
10-075-1071-2
SP10-02801
SP10-02801SP10-02801
FP10-02501
FP10-02501FP10-02501
CP10-04902
CP10-04902CP10-04902
Q'TY
1
2
1
1
TEMPLATE
1
100-294-942
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
ＰＡＣＫＩＮＧ ＬＩＳＴ
C2025-Z05-A
A - 1A
ＰＡＣＫＩＮＧ ＬＩＳＴ
ＰＡＣＫＩＮＧ ＬＩＳＴＰＡＣＫＩＮＧ ＬＩＳＴ
MU-150C-H-AC-CS
MU-150C-H-AC-CS
MU-150C-H-AC-CSMU-150C-H-AC-CS
10CQ-X-9855 -1
1/1
N A M E
ユニット
ユニット UNIT
ユニットユニット
15型ｶﾗｰLCD表示器
MULTI-PURPOSE LCD DISPLAY
予備品
予備品 SPARE PARTS
予備品予備品
ﾋｭｰｽﾞ
FUSE
付属品
付属品 ACCESSORIES
付属品付属品
ﾛｺﾞｼｰﾄ
LOGO SEAL
工事材料
工事材料 INSTALLATION MATERIALS
工事材料工事材料
ｺﾈｸﾀ(SRCN)
CONNECTOR
その他工材
その他工材 OTHER INSTALLATION MATERIALS
その他工材その他工材
装備用型紙
UNIT
UNITUNIT
SPARE PARTS SP10-02802
SPARE PARTSSPARE PARTS
ACCESSORIES FP10-02501
ACCESSORIESACCESSORIES
INSTALLATION MATERIALS CP10-04901
INSTALLATION MATERIALSINSTALLATION MATERIALS
OTHER INSTALLATION MATERIALS
OTHER INSTALLATION MATERIALSOTHER INSTALLATION MATERIALS
O U T L I N E
DESCRIPTION/CODE №
MU-150C-H-AC
000-012-617
FGMB 1.5A 250V
000-145-654
10-075-1052-0
100-294-900
SRCN6A13-3S
000-508-665
10-075-1071-2
SP10-02802
SP10-02802SP10-02802
FP10-02501
FP10-02501FP10-02501
CP10-04901
CP10-04901CP10-04901
Q'TY
1
2
1
1
TEMPLATE
1
100-294-942
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）
A - 2
9-52 Ashihara-cho,9-52 Ashihara-cho,
A
A
*
00080923101
**00080923101
*
*
00080923101
**00080923101
*
*
OME
20250
C
30
**OME
20250
C
30
**OME
20250
C
30
**OME
20250
C
30
*
Nishinomiya 662-8580, JAPANNishinomiya 662-8580, JAPAN
Telephone :Telephone : 0798-65-21110798-65-2111
FaxFax 0798-65-42000798-65-4200
ll rights reserved.
ll rights reserved.
::
Printed in JapanPrinted in Japan
Pub. No.Pub. No. OME-20250OME-20250
Your Local Agent/DealerYour Local Agent/Dealer
IRST EDITION :
IRST EDITION : JANJAN.. 20022002
C3C3 ::OCTOCT.. 04, 200404, 2004
(( YOTAYOTA ))
MU-150CMU-150C
* 0 0 0 8 0 9 2 3 1 0 1 ** 0 0 0 8 0 9 2 3 1 0 1 *
* O M E 2 0 2 5 0 C 3 0 ** O M E 2 0 2 5 0 C 3 0 *
Loading...