Furuno GP-36 Dgps, GP-31 GPS User Manual
GP-36 DGPS NAVIGATOR
GP-31 GPS NAVIGATOR
Operator's Guide
The purpose of this operator's guide is to provide the basic operating procedures for this equipment.
For detailed information, refer to the operator's manual.
Selecting Display Mode
Press the [DISP] key until desired display mode
appears.
2D
15: 37: 40
PWR
24.0
SPD
10.0
CSE
357°
[User Display: Speedometer]
2D
10–APR–99 15:37:40
PWR
SPD
10.0
[User Display: Digital Data]
2D
10–APR–99 15:37:40
34°44. 000' N
135°21. 000'
10.0 357°
SPD:
[Nav Data Display]
30
20
v
10
k
t
0
TRIP 0.00 nm
(Display format
depends on user setting.)
OR
24.0
v
kt CSE
kt
357°
(Display format
depends on user setting.)
E
CSE:
2D
n
40
50
60
[ 5 ]
m
CSE:
357°
SPD:
k
10.0
t
34°44.000N 135°21.000E
X
[Plotter Display]
004
BRG
CSE
RNG
SPD
242°
357°
n
17.5
m
k
t
10.0
a
0.05 0.05
0.5
XTE
[+]
0.05
[Highway Display]
2D MAG
SPD:
RNG:
TTG:
CURSOR
300 330
30 60
NE
kt
10.0
17.5 nm
1H30M 12:30
CSE:
BRG:
ETA:
15:37
°
357
242°
[Steering Display]
Enlarging, Shrinking the Display Range
1. Press the [MENU] key.
2. Press the [ENT] key.
3. Press ▲ to increase; ▼ to decrease.
4. Press the [ENT] key to close the window.
Shifting the Cursor, Display
1. On the plotter display, press the cursor pad
n
m
to turn on and shift the cursor.
2. Place the cursor on an edge of the screen
and use the cursor pad to shift the display.
Centering Own Position
1. Press the [MENU] key.
2. Select “SHIP TO CENTER?”.
3. Press the [ENT] key.
Entering MOB Mark
1. Press the [MARK/MOB] key.
2. Select “MOB?”.
3. Press the [ENT] key.
4. Press the [ENT] key again.
Registering Waypoints
Setting, Cancelling
A waypoint can be entered four ways. Below is
the procedure for entry by the cursor.
1. Operate the cursor pad to place the cursor
on the location where you want to inscribe a
waypoint.
2. Press the [ENT] key.
CURSOR POS. → WYPT
ENTER A NEW WYPT NAME.
0 0 1 – – – ?
( 001: DEFAULT NAME )
Quit : [MENU]
3. Press the [ENT] key.
NAME: KOBE
34°44.000’N MARK
135°21.000’E x
10—APR 11:25 AMD
Exit? LOG RT?
4. Place the cursor under “MARK”.
5. Press the [ENT] key.
6. Press ▲ or ▼ to select mark shape desired.
7. Press the [ENT] key.
8. Select “Exit?” and then press the [ENT] key.
Destination
Destination can be set three ways. Below is the
method for setting destination by the cursor.
To set destination by cursor;
1. Press the [GOTO] key.
2. Select “CURSOR?”.
3. Press the [ENT] key.
4. Place the cursor on position to set as destination.
5. Press the [ENT] key.
To cancel destination;
1. Press the [GOTO] key.
2. Select “OFF?”.
3. Press the [ENT] key.
Setting the Arrival Alarm
1. Press the [MENU] key once or twice to display the menu.
2. Select “ALARMS”.
3. Press the [ENT] key.
4. Select “ARV/ANC” and press the [ENT] key.
5. Select “ARV” and press the [ENT] key.
6. Press the [ENT] key and enter arrival alarm
range with the cursor pad.
7. Press the [ENT] key.
8. Press the [MENU] key twice to finish.
Registering Routes
1. Press the [MENU] key once or twice to display the menu.
2. Select “ROUTES”.
3. Press the [ENT] key.
4. Press the [ENT] key.
5. Press the [ENT] key, select route waypoint
and press the [ENT] key.
6. Repeat step 5 to enter other waypoints on
the route.
7. Select “Exit?” to register route and finish.
8. Press the [ENT] key to register.
PUB.NO.OSE-43990-A
(9905,DAMI) GP-31/36
Loading...