Furuno GP-1610CF User Manual

GP-1610CF

Color GPS Plotter Sounder

The purpose of this Operator's Guide is to provide the basic operating procedures for this equip­ment. For more detailed information see the operator's manual.

Waypoint

(Marks important

point (buoy, etc.);

can be set as

destination.)

Chart

(Requires chart

card.)

Mark

(Marks point
of interest,
reef, etc.)

Own ship mark

(Shows current
position.)

Course

Depth

PLOTTER
DISPLAY

01

50k

SOUNDER
DISPLAY

100

150

200

CSE 350.0° SPD 16.8kt 2D
DEP 110 m

TMP 16.0°C 13:42

POS 34°26.345’N 135°41.232’E

50

0

Depth scale

(Shown here
in meters.)

Course bar

Fish school

Bottom
Ship’s track

Sounder frequency

Speed
Position-fixing mode

Time
Position

Water temperature

(Requires sensor.)

Sample plotter/sounder display

The GP-1610CF is a fully integrated color video sounder, color video plotter and GPS receiver.
To find position, simply turn on the power. As your boat moves its track is inscribed on the
display.

1

Use the proper fuse.

Use of a wrong fuse can result in fire or
permanent equipment damage.

GPS position and velocity accuracies
are controlled by the U.S. Department
of Defense. Position may be degraded
up to 100 meters.

Do not use the equipment for other than
its intended purpose.

Personal injury can result if the equipment
is used as a chair or stepping stool, for
example.

Do not place objects on the top of the
equipment.

The equipment can overheat or personal
injury can result if the object falls.

CAUTION

SAFETY INSTRUCTIONS

WARNING

Do not open the equipment.

Hazardous voltage which can
cause electrical shock, burn or
serious injury exists inside the
equipment. Only qualified
personnel should work inside
the equipment.

Do not disassemble or modify the
equipment.

Fire, electrical shock or serious injury
can result.

Turn off the power immediately if water
leaks into the equipment or the equip­ment is emitting smoke or fire.

Continued use of the equipment can cause
fire or electrical shock.

Do not place liquid-filled containers on
the top of the equipment.

Fire or electrical shock can result if a
liquid spills into the equipment.

Do not operate the equipment with wet
hands.

Electrical shock can result.

Keep heater away from equipment.

Heat can alter equipment shape and melt
the power cord, which can cause fire or
electrical shock.

2

Inserting a Chart Card

T

1 Turn off the power.
2 Open the chart card drive cover at the bottom of the display unit.

Screws

Cover

3 Insert chart card label side up, arrow forward.

Arrow forward

Chart
card

EJEC
button

4 Close the chart card drive cover.

To eject a chart card:

1 Open the chart card drive cover .
2 Press the EJECT button.

Note: If no chart card is inserted a general world map appears.

3

Displaying the Plotter Picture

Press the POWER key to turn on the equipment. A beep sounds and shortly thereafter the plotter
display appears.

1 Press the POWER key.

Results of self-test;
displayed for about
one second.

Warning on chart
card usage; appears
for about one minute.

Plotter display
(Position being
calculated.)

ROM
RAM
VRAM
Battery

Program No.
Base Chart No.

NO NATIONAL HYDROGRAPHIC
OFFICE HAS VERIFIED THE
INFORMATION IN THIS COASTLINE
DATA CARD AND NONE ACCEPT
LIABILITY FOR THE ACCURACY OF
REPRODUCTION OR ANY
MODIFICATIONS MADE THEREAFTER.
THIS PRODUCT WITH THIS
COASTLINE DATA CARD DOES NOT
REPLACE THE REQUIREMENT TO
USE THE APPROPRIATE PRODUCTS
FOR NAVIGATION ACCORDING TO
NATIONAL AND INTERNATIONAL
REGULATONS.

FURUNO ELECTRIC CO., LTD.

OK
OK
OK
OK

02522531**

=
=

— — WARNING— —

MENU

SNDR1PLTR

AUTO

ZOOM
IN 4

CNTR

TONE

NU/CU

ESC

WPT3GOTO

ENT

EVENT

2

MOB 7

ZOOM
OUT 9

CURS

5

CLR

POWER

6

8

0

1

BRG+ 232.0° RNG+ 0.00nm ACQ
DEP 110m TMP 16 .0°C 13:41
+ 34°43.801’N 135°21.163’E

ACQ means acquiring
satellite; position is
not reliable.

Plotter display
(Position now reliable.
Chart appears about
20 sec after power
is turned on. At initial
power on it takes
two minutes.)

2D or 3D means

BRG+ 232.0° RNG+ 0.00nm 2D
DEP 110m TMP 16 .0°C 13:41
+ 34°43.801’N 135°21.163’E

position is reliable.
Confirm this indi­cation before using
the equipment.

4

MENU

ESC

NU/CU

ENT

SNDR1PLTR

6

AUTO

2

EVENT

MOB 7

WPT3GOTO

8

ZOOM
OUT 9

CNTR

5

CLR

TONE

POWER

ZOOM
IN 4

CURS

0

3

2

1

Adjusting Tone and Brilliance

1 Press the TONE key.

Adjust tone or brilliance
within 10 seconds,
otherwise the display
will be erased.

Ten levels of tone are
provided.

Eight levels of brilliance
are provided.

LOW HIGH

TONE : 5

LOW HIGH

BRILL : 8

2 Press t or s to adjust tone.

3 Press ▲ or ▼ to adjust

brilliance.

5

Changing the Display

There are ten displays. Below is the procedure for how to display the three most common dis­plays.

The plotter display is currently
shown. This display shows
chart, ship’s track (when ship
moves), etc.

Switch to the
normal sounder
display.

Confirm that "Normal" appears
in reverse video. If it does not,
press ▲ to do so.

BRG+ 232.0° RNG+ 0.00nm 2D
DEP 110m TMP 16 .0°C 13:41
+ 34°43.801’N 135°21.163’E

1 Press the SNDR key.

SELECT SOUNDER MODE

Normal

Marker Zoom
Bottom Zoom
Bottom Lock
A-Scope

50kHz

200kHz

SNDR: Sel ESC: Close

2 Press the ESC key.

2
1

MENU

ESC

SNDR

1

AUTO

2

WPT3GOTO

ZOOM
IN 4

CNTR

5

TONE

NU/CU

ENT

PLTR

EVENT
MOB 7

ZOOM
OUT 9

CURS

CLR

POWER

6

8

0

The sounder display shows
underwater conditions.

6

162

CSE 180.0° SPD 16.8kt
DEP 162m TMP 16.0 °C
POS 34° 26.245’ N 135° 41.232’ E

50k

0

50

100

150

200

2D

13:41