Furuno 1954c, 1834c, 1934c, 1964c User Manual

Download

IMPORTANT NOTICES

General

• This manual has been authored with simplified grammar, to meet the needs of

international users.

• The operator of this equipment must read and follow the descriptions in this manual.

Wrong operation or maintenance can cancel the warranty or cause injury.

• Do not copy any part of this manual without written permission from FURUNO.

• If this manual is lost or worn, contact your dealer about replacement.

• The contents of this manual and equipment specifications can change without notice.

• The example screens (or illustrations) shown in this manual can be different from the

screens you see on your display. The screens you see depend on your system configuration and equipment settings.

• Save this manual for future reference.

• Any modification of the equipment (including software) by persons not authorized by

FURUNO will cancel the warranty.

• All brand and product names are trademarks, registered trademarks or service marks of

their respective holders.

• “C- MAP” means “C-MAP by Jeppesen” in this manual.

How to discard this product

Discard this product according to local regulations for the disposal of industrial waste. For disposal in the USA, see the homepage of the Electronics Industries Alliance (http://www.eiae.org/) for the correct method of disposal.

How to discard a used battery

Some FURUNO products have a battery(ies). To see if your product has a battery, see the chapter on Maintenance. Follow the instructions below if a battery is used. Tape the + and terminals of battery before disposal to prevent fire, heat generation caused by short circuit.

In the European Union

The crossed-out trash can symbol indicates that all types of batteries must not be discarded in standard trash, or at a trash site. Take the used batteries to a battery collection site according to your national legislation and the Batteries Directive 2006/66/EU.

In the USA

The Mobius loop symbol (three chasing arrows) indicates that Ni-Cd and lead-acid rechargeable batteries must be recycled. Take the used batteries to a battery collection site according to local laws.

Ni-Cd Pb

In the other countries

There are no international standards for the battery recycle symbol. The number of symbols can increase when the other countries make their own recycling symbols in the future.

SAFETY INSTRUCTIONS

WARNING

ELECTRICAL SHOCK HAZARD

Do not open the equipment.

Only qualified personnel should work inside the equipment.

Turn off the radar power switch before servicing the antenna unit. Post a warning sign near the switch indicating it should not be turned on while the antenna unit is being serviced.

Prevent the potential risk of being struck by the rotating antenna and exposure to RF radiation hazard.

Wear a safety belt and hard hat when working on the antenna unit.

Serious injury or death can result if someone falls from the radar antenna mast.

Do not disassemble or modify the equipment.

Fire, electrical shock or serious injury can result.

Turn off the power immediately if water leaks into the equipment or the equipment is emitting smoke or fire.

Continued use of the equipment can cause fire or electrical shock.

Use the proper fuse.

Fuse rating is shown on the power cable. Use of a wrong fuse can result in damage to the equipment.

Keep heater away from equipment.

Heat can alter equipment shape and melt the power cord, which can cause fire or electrical shock.

WARNING

Radio Frequency Radiation Hazard

The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the transmitting antenna at a close distance.

Distances at which RF radiation levels of 100 and 10 W/m table below.

Note: If the antenna unit is installed at a close distance in front of the wheel house, your administration may require halt of transmission within a certain sector of antenna revolution. This is possible - Ask your FURUNO representative or dealer to provide this feature.

MODEL

MODEL 1824C

MODEL 1834C

MODEL 1934C

MODEL 1944C

XN-12A

MODEL 1954C

XN-13A

XN-12A

MODEL 1964C

XN-13A

Warning Label

A warning label is attached to the equipment. Do not remove the label. If the label is missing or damaged, contact a FURUNO agent or dealer.

WARNING

To avoid electrical shock, do not remove cover. No user-serviceable parts inside.

exist are given in the

Distance to

100 W/m

point

Nil

Worst case

0.10 m

Nil

0.20 m

Nil

0.50 m

0.40 m

Distance to

Worst case

Worst case 2.00 m

Worst case 1.40 m

Worst case 5.40 m

Worst case 3.60 m

Name: Warning Label (1) Type: 86-003-1011-0 Code No.: 100-236-230

10 W/m

point

0.70 m

1.50 m

1.70 m

1.20 m

FOREWORD ...................................................................................................... viii

SYSTEM CONFIGURATIONS .............................................................................. x

1. OPERATIONAL OVERVIEW .......................................................................1-1

1.1 Operating Controls .............................................................................................................1-1

1.2 Inserting a Chart Card........................................................................................................1-3

1.3 Turning the Unit On/Off ......................................................................................................1-4

1.4 Display Brilliance, Panel Brilliance, Hue.............................................................................1-5

1.4.1 Display brilliance, panel brilliance ..........................................................................1-5

1.4.2 Hue ........................................................................................................................1-6

1.5 Selecting a Display.............................................................................................................1-7

1.5.1 Display modes .......................................................................................................1-7

1.5.2 Selecting a display .................................................................................................1-8

1.5.3 Switching control in combination and overlay screens...........................................1-9

1.5.4 Selecting image source........................................................................................1-10

1.6 Trackball, Cursor.............................................................................................................. 1-11

1.7 Entering the MOB Mark, Setting MOB as Destination......................................................1-12

1.8 Data Boxes.......................................................................................................................1-13

1.8.1 Showing, hiding data boxes with soft key.............................................................1-13

1.8.2 Rearranging data boxes.......................................................................................1-13

1.8.3 Temporarily erasing a data box ............................................................................1-13

1.9 Function Keys

1.10 Simulation Display............................................................................................................1-15

..................................................................................................................1-14

2. RADAR OPERATION ..................................................................................2-1

2.1 Radar Display.....................................................................................................................2-1

2.2 Transmitting, Stand-by .......................................................................................................2-1

2.3 Tuning ................................................................................................................................2-2

2.4 Adjusting the Gain..............................................................................................................2-2

2.5 Reducing Sea Clutter .........................................................................................................2-3

2.5.1 How the A/C SEA works.........................................................................................2-3

2.5.2 Adjusting the A/C SEA ...........................................................................................2-4

2.6 Reducing Precipitation Clutter............................................................................................2-4

2.6.1 Adjusting the A/C RAIN..........................................................................................2-4

2.7 Range Scale ......................................................................................................................2-5

2.8 Pulselength ........................................................................................................................2-5

2.9 Presentation Mode .............................................................................................................2-6

2.9.1 Selecting a presentation mode...............................................................................2-6

2.9.2 Description of presentation modes.........................................................................2-7

2.10 Measuring the Range.........................................................................................................2-8

2.10.1 Measuring range by range rings ............................................................................2-8

2.10.2 Measuring range by cursor ....................................................................................2-8

2.10.3 Measuring range by VRM ......................................................................................

2.10.4 Various VRM operations..........................................................................................2-9

2.11 Measuring the Bearing .....................................................................................................2-10

2.11.1 Measuring bearing by cursor................................................................................2-10

2.11.2 Measuring bearing by EBL...................................................................................2-10

2.11.3 Various EBL operations .........................................................................................2-10

2-9

iii

TABLE OF CONTENTS

2.12 Erasing the Heading Line, North Marker.......................................................................... 2-11

2.13 Reducing Noise Interference............................................................................................2-11

2.14 Rejecting Radar Interference ........................................................................................... 2-11

2.15 Zoom................................................................................................................................2-12

2.15.1 Zooming radar targets..........................................................................................2-12

2.15.2 Zooming ARP, TTM targets ..................................................................................2-13

2.16 Shifting the Picture ...........................................................................................................2-14

2.16.1 Manual shift..........................................................................................................2-14

2.16.2 Automatic shift .....................................................................................................2-14

2.17 Using the Offset EBL .......................................................................................................2-15

2.17.1 Predicting collision course ...................................................................................2-15

2.17.2 Measuring range & bearing between two targets.................................................2-16

2.18 Echo Trails .......................................................................................................................2-17

2.18.1 Trail time ..............................................................................................................2-17

2.18.2 Starting echo trails ...............................................................................................2-18

2.18.3 Trail gradation ......................................................................................................2-18

2.18.4 Trail color .............................................................................................................2-18

2.18.5

2.19 Echo Stretch ....................................................................................................................2-19

2.20 Echo Averaging................................................................................................................ 2-20

2.21 Outputting TLL Data.........................................................................................................2-21

2.22 Guard Alarm.....................................................................................................................2-22

2.22.1 Setting a guard alarm zone ..................................................................................2-22

2.22.2 When the alarm is violated… ...............................................................................2-23

2.22.3 Cancelling the guard alarm ..................................................................................2-23

2.23 Watchman........................................................................................................................2-23

2.23.1 How watchman works ..........................................................................................2-23

2.23.2 Turning on/off watchman......................................................................................2-23

2.23.3 Setting watchman stand-by interval .....................................................................2-24

2.24 Suppressing Second-trace Echoes..................................................................................2-24

2.25 Waypoint Marker.............................................................................................................. 2-25

2.26 ARP, TTM Operation ........................................................................................................ 2-26

2.26.1 Activating/deactivating ARP, TTM ........................................................................2-27

2.26.2 Acquiring and tracking targets (ARP)...................................................................2-27

2.26.3 Displayi

2.26.4 Terminating tracking of ARP targets.....................................................................2-29

2.26.5 Setting vector attributes (ARP) ............................................................................2-30

2.26.6 Displaying past position (ARP).............................................................................2-31

2.26.7 ARP, TTM target data...........................................................................................2-31

2.26.8 CPA/TCPA alarm (ARP)....................................................................................... 2-32

2.26.9 Lost target alarm (ARP) .......................................................................................2-33

2.27 Interpreting the Radar Display .........................................................................................2-34

2.27.1 False echoes ....................................................................................................... 2-34

2.27.2 SART (Search and Rescue Transponder)............................................................2-35

2.27.3 Racon (Radar Beacon) ........................................................................................2-36

Echo trail mode

ng target number (ARP, TTM)..................................................................2-29

....................................................................................................2-19

3. PLOTTER OPERATION .............................................................................. 3-1

3.1 Plotter Displays..................................................................................................................3-1

3.1.1 Full-screen plotter display...................................................................................... 3-1

3.1.2 Nav graphic display................................................................................................3-3

3.1.3 Highway display.....................................................................................................3-6

3.1.4 Nav data display ....................................................................................................3-7

3.2 Presentation Mode.............................................................................................................3-8

3.3 Shifting the Display ............................................................................................................3-9

3.4 Chart Scale ........................................................................................................................3-9

3.5 Chart Cards ........................................................................................................................ 3-9

3.5.1 Chart card overview......................................................................................... 3-9

3.5.2 Indices and chart enlargement....................................................................... 3-10

3.5.3 Navionics

3.5.4 C-MAP by Jeppesen charts ........................................................................... 3-14

3.6 Working with Track ........................................................................................................... 3-18

3.6.1 Displaying track ............................................................................................. 3-18

3.6.2 Stopping, restarting plotting of own ship track ............................................... 3-19

3.6.3 Changing track color...................................................................................... 3-19

3.6.4 Track plotting method and interval for own ship track.................................... 3-20

3.6.5 Changing own ship track/mark distribution setting......................................... 3-21

3.6.6 Erasing track.................................................................................................. 3-22

3.7 Marks, Lines ..................................................................................................................... 3-23

3.7.1 Entering a mark, line...................................................................................... 3-23

3.7.2 Changing mark attributes............................................................................... 3-24

3.7.3 Selecting line type.......................................................................................... 3-24

3.7.4 Erasing marks, lines....................................................................................... 3-25

3.8 Waypoints......................................................................................................................... 3-26

3.8.1 Entering waypoints......................................................................................... 3-26

3.8.2 Editing waypoint data..................................................................................... 3-29

3.8.3 Erasing waypoints.......................................................................................... 3-30

3.8.4 Changing waypoint mark size (Navionics GOLD).......................................... 3-31

3.8.5 Searching waypoints...................................................................................... 3-32

3.9 Routes .............................................................................................................................. 3-33

3.9.1 Creating routes .............................................................................................. 3-33

3.9.2 Connecting routes.......................................................................................... 3-36

3.9.3 Inserting waypoints ........................................................................................ 3-37

3.9.4 Removing waypoints from a route ................................................................. 3-38

3.9.5 Erasing routes................................................................................................ 3-39

3.10 Navigation ........................................................................................................................ 3-39

3.10.1 Navigating to a “quick point” .......................................................................... 3-39

3.10.2 Navigating to waypoints................................................................................. 3-40

3.10.3 Navigating to ports, port services (NavChart only) ........................................ 3-41

3.10.4 Following a route ........................................................................................... 3-43

3.10.5 Cancelling route navigtion.............................................................................. 3-46

3.11 Alarms .............................................................................................................................. 3-47

3.11.1 Audio alarm on/off.......................................................................................... 3-47

3.11.2 Arrival alarm................................................................................................... 3-48

3.11.3 Anchor watch alarm ....................................................................................... 3-49

3.11.4 XTE (Cross-Track Error) alarm ...................................................................... 3-50

3.11.5 Speed alarm................................................................................................... 3-50

3.11.6 Proximity alarm .............................................................................................. 3-51

3.11.7 Trip alarm....................................................................................................... 3-51

3.11.8 Grounding alarm (C-MAP by Jeppesen specification).................................... 3-52

3.11.9 Alarm information........................................................................................... 3-53

3.12 Resetting Trip Distance .................................................................................................... 3-55

charts .............................................................................................3-11

4. VIDEO SOUNDER OPERATION ................................................................. 4-1

4.1 Sounder Displays ............................................................................................................... 4-1

4.1.1 Selecting a sounder display............................................................................. 4-1

4.1.2 Description of sounder displays....................................................................... 4-2

4.1.3 Selecting screen split method in combination displays.................................... 4-6

4.2 Automatic Sounder Operation ............................................................................................ 4-6

4.2.1 How the automatic sounder works................................................................... 4-6

4.2.2 Types of automatic sounder modes ................................................................. 4-6

4.2.3 How to enable automatic sounder operation ................................................... 4-7

TABLE OF CONTENTS

4.3 Manual Sounder Operation................................................................................................4-7

4.3.1 Selecting the manual mode ...................................................................................4-7

4.3.2 Selecting display range..........................................................................................4-7

4.3.3 Adjusting the gain ..................................................................................................4-8

4.3.4 Shifting the range...................................................................................................4-8

4.4 Measuring Depth, Time...................................................................................................... 4-9

4.5 Reducing Interference........................................................................................................4-9

4.6 Reducing Low Level Noise ..............................................................................................4-10

4.7 Erasing Weak Echoes...................................................................................................... 4-11

4.8 White Marker....................................................................................................................4-12

4.9 Picture Advance Speed.................................................................................................... 4-12

4.9.1 Advancement independent of ship’s speed .........................................................4-12

4.9.2 Advancement synchronized with ship’s speed.....................................................4-13

4.10 Display Colors..................................................................................................................4-14

4.11 Alarms..............................................................................................................................4-15

4.11.1 Audio alarm on/off................................................................................................4-15

4.11.2 Bottom alarm .......................................................................................................4-16

4.11.3

Fish alarm ............................................................................................................

4.11.4 Fish alarm (B/L) ...................................................................................................4-17

4.11.5 Water temperature alarm .....................................................................................4-17

4.11.6 When an alarm setting is violated... .....................................................................4-18

4.12 Water Temperature Graph ...............................................................................................4-19

4.13 Changing Pulse Repetition Rate......................................................................................4-19

4.14 Saving Sounder Picture to an SD Card............................................................................ 4-19

4.15 Interpreting the Sounder Display......................................................................................4-20

4.15.1 Zero line ............................................................................................................... 4-20

4.15.2 Bottom echo.........................................................................................................4-20

4.15.3 Fish school echoes .............................................................................................. 4-21

4.15.4 Surface noise/Aeration......................................................................................... 4-21

4-16

5. AIS OPERATION .........................................................................................5-1

5.1 Turning AIS Feature On/Off ...............................................................................................5-1

5.2 AIS Symbols ......................................................................................................................5-3

5.3 Setting Number of AIS Targets to Display ..........................................................................5-3

5.4 Activating Targets...............................................................................................................5-4

5.5 Displaying Target Data.......................................................................................................5-4

5.6 Lost Target .........................................................................................................................5-5

5.7 Setting CPA and TCPA.......................................................................................................5-5

5.8 Proximity Alarm..................................................................................................................5-6

5.9 Showing, Hiding AIS Target Tracks....................................................................................5-7

5.10 Choosing Vector Time........................................................................................................5-7

5.11 Displaying Past Positions of AIS Targets............................................................................5-8

6. DATA TRANSFER .......................................................................................6-1

6.1 Memory Card Operations................................................................................................... 6-1

6.1.1 Deleting all data (other than chart data) from memory cards................................. 6-1

6.1.2 Saving data to a memory card ............................................................................... 6-2

6.1.3 Playing back data from a memory card..................................................................6-2

6.2 Uploading, Downloading Data............................................................................................6-4

6.2.1 Setting communication software on the PC ...........................................................6-4

6.2.2 Uploading or downloading data..............................................................................6-4

6.3 Loading Waypoint Data from Yeoman................................................................................6-7

6.4 Receiving Data Via Network Equipment ............................................................................6-8

6.5 Outputting Data Through the Network................................................................................6-9

7. CUSTOMIZING YOUR UNIT ....................................................................... 7-1

7.1 General Setup .................................................................................................................... 7-1

7.2 Radar Setup ....................................................................................................................... 7-4

7.2.1 Radar display setup ......................................................................................... 7-4

7.2.2 Radar range setup ........................................................................................... 7-7

7.2.3 Function key setup........................................................................................... 7-8

7.3 Plotter Setup..................................................................................................................... 7-10

7.3.1 Navigation options ......................................................................................... 7-10

7.3.2 Function key setup..........................................................................................7-11

7.4 Chart Setup ...................................................................................................................... 7-13

7.4.1 Chart offset .................................................................................................... 7-13

7.4.2 Navionics GOLD chart attributes ................................................................... 7-14

7.4.3 C-MAP by Jeppesen chart attributes ............................................................. 7-15

7.5 Data Boxes Setup ............................................................................................................ 7-20

7.6 Hot Page Setup ................................................................................................................ 7-21

7.7 Navigator Setup................................................................................................................ 7-22

7.7.1 Navigation data source .................................................................................. 7-22

7.7.2 FURUNO BB GPS receiver setup.................................................................. 7-24

7.7.3 TD display setup ............................................................................................ 7-27

7.8 Nav Data Display Setup ................................................................................................... 7-29

7.9 Sounder Setup ................................................................................................................. 7-30

7.9.1 System setup ................................................................................................. 7-30

7.9.2 Sensor setup.................................................................................................. 7-33

7.9.3 Sounding range, zoom range, bottom lock range.......................................... 7-34

7.9.4 Function key setup......................................................................................... 7-35

7.10 Nav Graphic Display Setup .............................................................................................. 7-37

8. MAINTENANCE, TROUBLESHOOTING .................................................... 8-1

8.1 Preventive Maintenance..................................................................................................... 8-2

8.2 Replacement of Battery on Circuit Board ........................................................................... 8-3

8.3 Replacement of Fuse ......................................................................................................... 8-3

8.4 Replacing the Magnetron ................................................................................................... 8-4

8.5 Replacing the Synchro Belt (1824C only) .......................................................................... 8-4

8.6 Trackball Maintenance ....................................................................................................... 8-4

8.7 Simple Troubleshooting...................................................................................................... 8-5

8.7.1 General ............................................................................................................ 8-5

8.7.2 Radar ............................................................................................................... 8-5

8.7.3 Plotter .............................................................................................................. 8-6

8.7.4 Sounder ........................................................................................................... 8-7

8.8 Diagnostics......................................................................................................................... 8-8

8.8.1 Memory I/O test ............................................................................................... 8-8

8.8.2 Test pattern .....................................................................................................8-11

8.8.3 Keyboard ....................................................................................................... 8-12

8.9 GPS Status Display .......................................................................................................... 8-13

8.10 Clearing Memories ........................................................................................................... 8-14

8.11 Error Messages ................................................................................................................ 8-15

APPENDIX ......................................................................................................AP-1

Menu Overview .........................................................................................................................AP-1

Geodetic Chart List .................................................................................................................AP-10

Icons ........................................................................................................................................AP-11

SPECIFICATIONS........................................................................................... SP-1

INDEX............................................................................................................... IN-1

vii

FOREWORD

A Word to the Owner of the Model 18x4C/19x4C Series Marine Radar, GD-1920C Color Video Plotter

FURUNO Electric Company thanks you for purchasing the Model 18x4C/19x4C Series Marine Radar, GD-1920C Color Video Plotter. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability.

Since 1948, FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers.

Your equipment is designed and constructed to meet the rigorous demands of the marine environment. However, no machine can perform its intended function unless properly installed and maintained. Please carefully read and follow the operation and maintenance procedures set forth in this manual.

We would appreciate feedback from you, the end-user, about whether we are achieving our purposes.

Thank you for considering and purchasing FURUNO.

Features

The 18x4C/19x4C Radar Series and the GD-1920C Video Plotter work within our network system called the “NavNet.” Each product has an IP address to communicate with NavNet compatible products within the network, using TCP/IP protocol through an Ethernet 10BASE-T network.

The main features are as follows:

• This NavNet series consists of the following models:

Model Output Range

Marine Radar Model 1824C 2.2 kW 24 nm

Marine Radar Model 1834C 4 kW 36 nm 60 cm, radome, 24 rpm

Marine Radar Model 1934C 4 kW 48 nm 3.5 ft, open, 24 rpm

Marine Radar Model 1944C 6 kW 64 nm 4 ft, open, 24 rpm

Marine Radar Model 1954C 12 kW

72 nm

Marine Radar Model 1964C 25 kW

Radar antenna size, type,

rotation speed

46 cm, radome, 24/30 rpm (auto-switching)

4/6 ft, open, 24 rpm (4 or 6 ft), 48 rpm (4 ft only)

Color Video Plotter GD-1920C — — —

viii

FOREWORD

• Bright 10.4” screen visible even under direct sunlight.

• User friendly operation with combination of discrete keys, soft keys, alphanumeric keys

and Trackball.

• Accepts the following SD chart cards: NAVIONICS GOLD or C-MAP NT charts, depending on specification. All names mentioned above are registered trademarks of their respective companies.

• Fast chart redraw.

• Built-in NavNet interface circuit board.

• Video input (video recorder, CCD device, etc.) available with installation of optional PIP

Board.

• Highly accurate, WAAS-capable 12-channel FURUNO BB GPS Receiver GP-320B/330B and Weather Station WS-200 optionally available. (Hereafer these models are collectively referred to as FURUNO BB GPS receiver.)

• User programmable function keys.

• Video sounder picture available with connection of the optional Network Sounder

ETR-6/10N or ETR-30N.

• The optional facsimile receiver FAX-30 receives facsimile pictures and navtex messages transmitted from facsimile and navtex stations.

/, NT MAX

SYSTEM CONFIGURATIONS

All NavNet products incorporate a “network circuit board” to integrate each NavNet product on board through an optional LAN cable (Ethernet 10BASE-T). Each NavNet product is assigned an IP address to enable transfer of images between other NavNet products. For example, video plotter pictures can be transferred to a radar and vice versa. Pictures received via the NavNet may be adjusted at the receiving end.

The number of display units which may be installed depends on the number of network sounder connected. For a system incorporating three or more products, a “hub” is required to process data.

For one network sounder: one radar and three plotters, or four plotters For two network sounder: one radar and two plotters, or four plotters

Note: NavNet2 equipment cannot be connected to initial version NavNet equipment.

NavNet system (Model 1824C/1834C/1934C/1944C/1954C/1964C)

MODEL

1964C

AIS transponder

Antenna Unit

MODEL

1954C

AIS Interface IF-1500AIS*

* No longer reqired for VX2 with latest software

MODEL

1934C

Power Supply Unit

PSU-005

(MODEL 1954C)

Power Supply Unit

PSU-008

(MODEL 1964C)

ARPA

ARP-11

(Built-in)

Rectifier

RU-3423

MODEL

1944C

MODEL

1834C

Display unit

RDP-149

Facsimile

Receiver

FAX-30

MODEL1824C

GPS Receiver

GP-320B/330B

Weather Station

WS-200

Echo sounder Navigator

External buzzer PC

VGA monitor Remote display Video equipment

Heading sensor

HUB

FA-30

AIS RECEIVER

12 - 24 VDC*

Network

Sounder

ETR-6/10N

ETR-30N

Other NavNet unit

(GD-1920C, etc.)

: Standard : Option : Local supply

100/110/115/220/230 VAC 1φ, 50/60 Hz*

*: The power for the power supply unit and display unit must be drawn from the same power source.

NavNet system (Model 1824C/1834C/1934C/1944C/1954C/1964C)

Single-unit NavNet system (GD-1920C)

* Not required for VX2 with latest software

SYSTEM CONFIGURATIONS

GPS Receiver

GP-320B/330B or

Weather Station WS-200

External buzzer

AIS transponder

Other NavNet Unit

(Model 1834C, etc.)

Facsimile

Receiver

FAX-30

AIS Interface Not required*

Display unit

RDP-149

ETR-6/10N

AIS RECEIVER

Network

Sounder

ETR-30N

VGA monitor Remote display PC Video equipment

ARPA

ARP-11

HUB

Echo sounder Navigator

FA-30

Rectifier

PR-62

12 - 24 VDC

: Standard : Option : Local supply

100/110/115/220/230 VAC 1φ, 50/60 Hz

Single-unit NavNet system (GD-1920C)

SYSTEM CONFIGURATIONS

Two-unit NavNet system

Radar Antenna Unit,

GPS Receiver

GP-320B/330B,

Radar Antenna Unit,

GPS Receiver

GP-320B/330B,

Weather Station WS-200

RADAR

PLOTTER

Radar, plotter data

Two-unit NavNet system

Three-or-more-unit NavNet system (Max. 4 display units)

Radar Antenna Unit,

GPS Receiver

GP-320B/330B,

Weather Station WS-200

Radar Antenna Unit,

GPS Receiver

GP-320B/330B,

Weather Station WS-200

RADAR

PLOTTER

Sounder data

Network Sounder

ETR-6/10N

ETR-30N

(option)

RADAR

PLOTTER

Radar data

HUB

Facsimile data

Facsimile

Receiver

FAX-30

(option)

Plotter data

Note: The picture disappears 10 seconds after the NavNet cable is disconnected from a "sub" NavNet display unit.

Three-or-more-unit NavNet system

PLOTTER

Sounder data

Network Sounder

ETR-6/10N

ETR-30N

(option)

RADAR

xii

1. OPERATIONAL OVERVIEW

This chapter provides the basic information needed to get you started using your radar, video plotter.

1.1 Operating Controls

Display unit controls

The radar, video plotter, sounder and chart systems are operated with the controls of the display unit. Ten keys are labeled and they provide the function shown on their labels. The five soft keys provide various functions according to current operating mode. The ENTER knob mainly functions to register selections on the menu and adjust the EBL, VRM and gain. The Trackball’s main function is to move the cursor across the screen. When you correctly execute an operation, the unit generates a beep. Invalid operation causes the unit to emit three beeps.

Displays the mode selection window.

Momentary press:

Registers own ship's position as a waypoint.

Press three seconds:

Marks man overboard position.

Soft keys

ABC

JKL

STU

EBL VRM

DEF

MNO

VWX

GHI

PQR

YZ&

_'#

GAIN

Trackball*

Shifts cursor EBL/VRM and cursor; selects menu items and options.

Opens/closes the alarm menu. Clears data; erases selected mark.

Opens/closes the main menu. Selects a range.

ENTER knob Push: Registers setting. Rotate: Adjusts, gain, VRM, EBL, etc.;

selects menu items and options. May also be used to enter alphanumeric data.

Enter alphanumeric data.

Radar: Displays the soft keys for adjustment of

gain, A/C SEA and A/C RAIN (FTC in case the

Shows or hides the soft keys, function keys, nav data alternately.

the radar source is MODEL 17x4 series).

Sounder: Adjusts gain. Long press: Turns power off.

Momentary press: Turns the power on;

opens the display for adjustment of brilliance and hue; shows RADAR STBY/TX soft key.

Chart drive

Displays soft keys for EBL/VRM.

*: When it has been some time since the trackball was last operated, the cursor may not track the movement of the trackball. In this case, move the trackball rapidly and then finely.

1-1

1. OPERATIONAL OVERVIEW

Soft keys

The function of the five soft keys changes according to the operation. Their labels for their current functions are shown on the screen to the left of the keys. To hide or show the soft keys, press the HIDE/SHOW key. Each press of the key shows preset soft keys, user function keys or turns off navigation information (at the top of the screen).

SOFT KEYS

Display unit

Some soft keys show the current setting of a soft key in reverse video as shown below.

3nm

12/

H-UP

°M

319. 9

TRAIL

TRAIL ON /OFF

TRAIL TIME

GRAD

SINGLE

TRAIL COLOR

RETURN

359.9 ˚R

11.70

Current option shown in reverse video

Radar Display

34° 22. 3456'N 359.9°M 080° 22. 3456'E

16.0nm

WP-002

FISH

BRIDGE

Plotter Display

19.9 kt 99.9 nm

TRIP

MARK ENTRY

MODE

NTH UP

NAV

D. BOX ON/OFF

POS

Radar and plotter displays

1-2

1. OPERATIONAL OVERVIEW

1.2 Inserting a Chart Card

Your unit reads SD cards, in the following formats: Navionics GOLD Chart cards or C-MAP

/NT MAX chart cards, depending on the type of display unit you have. Insert the

appropriate chart card for your area as follows:

1. Open the chart drive.

Chart drive

Display unit

2. Insert chart card label side up prior to turning on the power.

3. Close the lid.

To remove chart card, follow the steps shown below.

1. Press the MENU key to show the menu.

2. Press the SHOW/HIDE soft key.

3. Open the chart drive lid, and then push the card once and then pull it out.

Note 1: Do not remove a card while the chart is being drawn. This may cause the

equipment to freeze.

Note 2: Do not insert or remove a card while the power is on. This may cause the equipment to freeze.

Note 3: For multiple display units, do not use the same chart card type in more than one

display unit.

Note 4: Remove the card with care; rough handling can damage the card and destroy its

contents.

1-3

1. OPERATIONAL OVERVIEW

1.3 Turning the Unit On/Off

Press the POWER/BRILL key to turn the unit on. A beep sounds and then the equipment shows the startup NavNet screen (about 20 seconds), the product information screen, startup test results and chart usage disclaimer. During this period the equipment is inoperative. The startup test checks the ROM, RAM, internal battery and backup data for proper operation, displaying the results for each as OK or NG (No Good). If NG appears an appropriate message appears on the screen. For any NG, try to press any key to go to the chart disclaimer screen, then perform the diagnostic test as shown in the paragraph “8.8 Diagnostics.”

For start up with the radar display, the magnetron takes from one minute and thirty seconds to three minutes (depending on radar model) to warm up before the radar can be operated. The time remaining for warming up of the magnetron is counted down at the center of the display.

You may press any key at the chart disclaimer screen to show the last-used display, or wait several seconds to let the equipment do it for you.

To turn the unit off, press and hold down the POWER/BRILL key until the screen goes off (approx. 3 sec.). To protect the LCD attach the hard cover. Note that the network sounder will be turned off approx. three minutes after turning off the power. This is due to the system’s electrical characteristics.

Note: The first time you turn on the power (or any time the power is applied after a memory reset), you are asked if you want to start the simulation mode, which provides simulated operation of the equipment after the installation mode selection. Push the ENTER knob to start the simulation mode, or press the CLEAR key to start normal operation. For further details about the simulation mode, see the paragraph “1.10 Simulation Display.”

1-4

1. OPERATIONAL OVERVIEW

1.4 Display Brilliance, Panel Brilliance, Hue

You can adjust display brilliance, panel brilliance and hue as shown below.

1.4.1 Display brilliance, panel brilliance

1. Press the POWER/BRILL key momentarily. A set of soft keys for adjustment of

brilliance and hue appear.

Active soft key is highlighted.

3nm

12/

H-UP

319. 9

BRILL CONTST

DISPLY BRILL

34° 22. 3456'N 359.9°M TRIP NU 080° 22. 3456'E

19.9 kt 99.9 nm

16.0nm

BRILL CONTST

DISPLY BRILL

DISPLAY BRILLIANCE

Radar Display

PANEL BRILL

HUE

RADAR

STBY

RETURN

359.9 ˚R

11.70

WP-002

FISH

DISPLAY BRILLIANCE

BRIDGE

Plotter Display

PANEL BRILL

HUE

RADAR

STBY

RETURN

Brilliance adjustment soft keys

2. Press the DISPLY BRILL or PANEL BRILL soft key as appropriate. An adjustment

window appears at the bottom of the screen. This window shows the name of the item selected for adjustment plus current brilliance level, by bar graph.

DISPLAY BRILLIANCE

Display brilliance Panel brilliance

PANEL BRILLIANCE

Display brilliance and panel brilliance windows

3. Adjust the ENTER knob, clockwise to raise the setting or counterclockwise to decrease

it. You may also use the soft key pressed at step 2. Eight levels of display brilliance and panel brilliance are available.

4. Hit the RETURN soft key to finish.

Note 1: If the unit is turned off with minimum brilliance, the screen will be dark at the next power-up. Press the POWER/BRILL key consecutively to adjust the brilliance.

Note 2: This equipment does not have a contrast control.

1-5

1. OPERATIONAL OVERVIEW

1.4.2 Hue

You may select the colors for the radar and plotter displays as below.

1. Press the POWER/BRILL key momentarily.

2. Press the HUE soft key to show the hue setting window.

HUE

▲



DAY



NIGHT



TWILIGHT



MANUAL SET

▼

Hue window

3. Operate the Trackball to select hue desired, referring to the table below. MANUAL SET follows the color settings on the CHART DETAILS menu for the plotter and the RADAR DISPLAY SETUP menu for the radar.

Night Day Twilight

Characters Red Black Green

Radar ring Red Green Green

Radar echo Orange Multi Yellow

Background Black White Blue

Landmass (plotter) Orange* Light-orange* Orange*

* = Beige and light-beige on C-MAP display unit.

4. Hit the RETURN soft key to finish.

Note: When using the overlay screen, the own ship track will be hidden if the radar

background and own ship track are blue and the “MANUAL SET” hue setting is used. In this case, set HUE to other position and then return to “MANUAL” to show the own ship track in black.

1-6

1. OPERATIONAL OVERVIEW

1.5 Selecting a Display

1.5.1 Display modes

If you have a radar, navigator, network sounder and external video source (video recorder, etc., optional PIP board required) six full-screen displays are available: radar, plotter, echo sounder, nav data, overlay, and external video. In addition to the full-screen display, you can divide the screen into halves and thirds to show two and three sets of images on a combination display.

Full screen Combination screen Overlay screen (radar) (radar + plotter)

(plotter + radar only, requires L/L data)

Display screens

The table below shows the displays available with each screen type.

Screen type and available display screen

Full screen Combination screen options

(half- or thirds-screen)

Plotter, radar, sounder, nav data, external video, overlay

Plotter, radar, sounder, compass (or wind), highway, compass (or wind)/highway, nav data, overlay, external video

Overlay screen options

Radar + plotter

1-7

1. OPERATIONAL OVERVIEW

1.5.2 Selecting a display

1. Press the DISP key to show the display screen selection window. The icons of modes

not available are shaded. HOTPAGE 1-HOTPAGE 6 are user-arrangeable displays called “hot pages,” which you can configure as you like. For further details, see the paragraph “7.6 Hot Page Setup.”

Selected item

RADAR PLOTTER SOUNDER NAV DATA OVERLAY EXT VIDEO WX FAX

HOTPAGE 1 HOTPAGE 2 HOTPAGE 3 HOTPAGE 4 HOTPAGE 5 HOTPAGE 6

· TURN KNOB TO SELECT MODE AND PUSH KNOB TO ENTER.

· PUSH ANY SOFT KEY TO SELECT IMAGE SOURCE.

Basic display screens

Hot pages

Display screen selection window

Note: “WX FAX” is available only when the facsimile receiver FAX-30 is connected. If

the message “AUX SOURCE IS DISCONNECTED. PUSH ENT KNOB TO EXIT.”

appears, press the ENTER knob and select other item.

2. Rotate the ENTER knob to select a basic display screen or a hot page screen.

3. Push the ENTER knob.

4. If you select a basic display screen, a group of appropriate combination displays appear.

In the example below, the radar combination screens are shown. When WX FAX is selected at step 2, a combination display does not appear.

PUSH ENTER KNOB.

Radar combination screen selection window

5. Rotate the ENTER knob to select display desired.

6. Push the ENTER knob to finish.

1-8

RETURN

1. OPERATIONAL OVERVIEW

1.5.3 Switching control in combination and overlay screens

A soft key is provided in relevant combination and overlay screens to switch control between displays. In the example below, the CNTRL PLOTTR and CNTRL SNDR soft keys enable switching control between the plotter and sounder screens in the plotter/sounder combination display.

34° 22. 3456’N 359.9°M TRIP NU 080° 22. 3456’E

16.0nm

WP-002

19.9 kt 99.9 nm

FISH

Plotter display selected

CNTRL

PLOTTR

To adjust sounder

34° 22. 3456’N 359.9°M TRIP NU

080° 22. 3456’E

16.0nm

19.9 kt 99.9 nm

50k

0’33"

40.0

0’33"

MARK ENTRY

MODE

NTH UP

NAV

POS

100

CNTRL

150

PLOTTR

200

CNTRL

SNDR

To adjust plotter

SHIFT

MODE

FREQ

100

LF/HF

DISPLAY MODE

150

CNTRL

SNDR

WP-002

FISH

Sounder display selected

50k

200

How to switch control between modes in the plotter/sounder combination display

1-9

1. OPERATIONAL OVERVIEW

1.5.4 Selecting image source

When more than one network radar or network sounder is connected to the equipment, you may select an image source for each as shown below. This is not necessary when only one network radar or network sounder is connected.

1. Press the DISP key.

2. Press any soft key to show the following display.

▲

RADAR SOURCE1 (HOST NAME: NAVNET1) SOUNDER SOURCE AUX SOURCE AUX 1 (HOST NAME: WXFAX) IP ADDRESS 172.031.003.003 DEVICE NUMBER 1 (HOST NAME: NAVNET-1)

ETR1 (HOST NAME: SOUNDER)

IF THERE IS MORE THAN ONE NETWORK RADAR OR ECHO SOUNDER, YOU MAY SELECT THE IMAGE SOURCES FOR DISPLAY.

SELECT SOURCE

EDIT

RETURN

Select source menu

3. Use the Trackball to select RADAR SOURCE, SOUNDER SOURCE or AUX SOURCE

as appropriate, then press the EDIT key.

RADAR SOURCE

▲



1 (NAVNET1)



2 (NAVNET2)



3 (NAVNET3)



4 (NAVNET4)

▼

Radar source

SOUNDER SOURCE

▲



ETR0 (SOUNDER)



ETR1 (SOUNDER1)



ETR2 (SOUNDER2)



ETR3 (SOUNDER3)



ETR4 (SOUNDER4)



ETR5 (SOUNDER5)



ETR6 (SOUNDER6)



ETR7 (SOUNDER7)



ETR8 (SOUNDER8)



ETR9 (SOUNDER9)

▼

AUX SOURCE

▲



AUX1 (WXFAX)



AUX2 (WXFAX1)



AUX3 (WXFAX2)



AUX4 (WXFAX3)

▼

Aux source

Sounder source

Radar source and sounder source windows

4. Use the Trackball to choose source.

5. Push the ENTER knob to set.

6. Press the DISP key to finish.

7. Turn the power off and on again.

1-10

1. OPERATIONAL OVERVIEW

1.6 Trackball, Cursor

The Trackball functions to shift the cursor, for measurement of range and bearing to a location (radar) and latitude and longitude position (plotter). Roll the Trackball to shift the cursor. The cursor moves in the direction of Trackball rotation.

Cursor

3nm LP

12/ H-UP

319. 9

SIGNAL PROC.

RADAR DISPLY

NAV FUNC

TARGET

ZOOM & D. BOX

Cursor data L/L position, Range and bearing from own ship to cursor

Cursor

Radar Display

34° 22. 3456'N 272.4°M

080° 22. 3456'E

15.9 nm 99.9 nm

16.0nm

WP-002

FISH

BRIDGE

359.9 ˚R

11.70

Cursor Data Bearing from own ship to cursor Range from own ship to cursor

TRIP

MARK

ENTRY

MODE

NTH UP

CENTER

GO TO CURSOR

D. BOX ON/OFF

Plotter Display

Cursor, cursor data

1-11

1. OPERATIONAL OVERVIEW

1.7 Entering the MOB Mark, Setting MOB as

Destination

The MOB mark functions to mark man overboard position. You can inscribe the mark from any mode except nav data, when playing back data or conducting any test. Note that this function requires position data.

Range, bearing

Note: The function of the SAVE/MOB key depends on the setting of SAVE

Man overboard

Current

position

MOB KEY FUNCTION in the GENERAL SETUP menu. The description below shows the procedure using the default setting. For further details, see Save

MOB concept

MOB Key Function on page 7-2.

1. Press and hold down the SAVE/MOB key for about three seconds when someone falls

overboard. The display shows the waypoint number being saved (youngest empty waypoint number, 001-999) followed by the MOB confirmation window. Time remaining is counted down while pressing the SAVE/MOB key.

MOB mark

MOB Data Box Bearing and range to MOB position

(MOB)

162.5°

0.49 nm

WAYPOINT SAVED!

XXXWPT CONTINUE PUSHING FOR MOB!

XXX = Waypoint number

CONTINUE PUSHING FOR MOB!

XX SEC

XX = Time remaining is counted down.

MAN OVER BOARD! GO TO MOB? YES ... PUSH ENTER KNOB NO ... PUSH CLEAR KEY

MOB mark messages

2. Push the ENTER knob to select the MOB position as the destination, or press the

CLEAR key to only mark current ship’s position as a waypoint. If you select the MOB

position as destination;

A full-screen radar, plotter or overlay appears depending on the display in use. (If the

MOB key function is “MOB Without Confirmation” the range is automatically set to

0.5 nm.) Further, the waypoint marker appears on the radar display.

The MOB mark “MOB” appears at the MOB position and a blue line runs between it and

current position. This line shows the shortest course to the MOB position.

Range and bearing to the MOB position are shown in the MOB data box.

To erase an MOB mark from the plotter display, you must first erase its corresponding waypoint. Place the cursor on the MOB mark, then press the CLEAR key followed by pushing the ENTER knob to erase the waypoint. Then, repeat to erase the MOB mark.

Note: On the plotter display, this function can be done by pressing the uppermost soft key. For detail, see page 7-10.

1-12

1. OPERATIONAL OVERVIEW

1.8 Data Boxes

Data boxes, providing navigation data, may be shown on any full-screen display. Up to six data boxes (two in case of large characters) may be shown, and the default data boxes are position (in latitude and longitude), course over ground, speed over ground and trip log. The user may choose which data to display, where to locate it, and show or hide it as desired. In addition, data boxes may be set independently for each display mode (plotter, radar, sounder). For how to select data for the data boxes, see the paragraph “7.5 Data Boxes Setup.”

Data boxes

3nm

12/

H-UP

TRIP LOG

177nm

POSITION

58.535'N

36.496'W

122

COG

323.6

319. 9°

SIGNAL PROC.

RADAR DISPLY

NAV FUNC

TARGET

ZOOM &

SOG

20.0 kt

D. BOX

359.9 ˚R

11.70

Data boxes

34° 22. 3456'N 359.9°M 080° 22. 3456'E

16.0nm

WP-002

POSITION

122

FISH

58.535'N

36.496'W

TRIP LOG

177nm

Radar Display

Data boxes

1.8.1 Showing, hiding data boxes with soft key

Plotter: D. BOX ON/OFF Radar: ZOOM & D. BOX

→ D. BOX ON/OFF (EBL/VRM data box, cursor data

box also shown/hidden) Sounder: AUTO/D. BOX

→D. BOX ON/OFF

1.8.2 Rearranging data boxes

COG

323.6

19.9 kt 99.9 nm

SOG

20.0 kt

Plotter Display

TRIP

MARK ENTRY

MODE

NTH UP

NAV

POS

D. BOX

ON/OFF

You may select the location for data boxes as follows:

1. Using the Trackball, place the cursor inside the data box you wish to move. As the cursor enters the box it changes to a “hand”. Push the ENTER knob, and the hand changes to a fist, meaning the box is correctly selected.

2. Use the Trackball to move the data box to the location desired, then push the ENTER knob.

1.8.3 Temporarily erasing a data box

If a data box is obscuring a desired object, you may temporarily erase the box. Use the Trackball to place the cursor inside the data box you wish to erase, then press the CLEAR key. To redisplay the box, press the D. BOX soft key twice to display it.

1-13

1. OPERATIONAL OVERVIEW

1.9 Function Keys

The function keys provide for one-touch execution of a desired function. The default function key settings are as shown in the table below.

Function

Key

Radar Plotter Sounder

Default Setting, Key Label

#1 Heading line on/off, HL Track on/off, TRK TLL output, TLL

#2 Rings on/off, RNG Edit mark/line, EML Clutter, CLT

#3 Echo trail, TRL Ruler, RUL Signal level, SLV

#4 Offcenter, OFC

Add new waypoint,

Noise limiter, NL

ADD

#5 STBY/TX, TX

Waypoint

Picture advance, PA

alphanumeric list, ALP

Executing a function

1. Press the HIDE/SHOW key to replace the preset soft key labels with the function key labels.

3nm

12/

H-UP

319. 9

R N G

Function

keys

F C

34° 22. 3456'N 359.9°M

080° 22. 3456'E 19.9 kt 99.9nm

16.0 nm

002WP

FISH

BRIDGE

TRIP

K E

L R

Function

keys

A D D

A L P

359.9 ˚R

11.70

Radar Display

Plotter Display

Function keys

2. Press function key desired.

Note: Function keys can be individually programmed for the plotter, radar and sounder displays. For further details see the following:

Radar: paragraph 7.2.3 Plotter: paragraph 7.3.2 Sounder: paragraph 7.9.4

1-14

1. OPERATIONAL OVERVIEW

1.10 Simulation Display

The simulation display, for use by service technicians for demonstration purposes, provides simulated operation to help acquaint you with the many features your unit has to offer. It allows you to view and control a simulated plotter, radar and sounder picture, without position-fixing equipment, network radar or a network sounder. Most controls are operative, thus you may practice setting destination, enter waypoints, measure range and bearing to a target, etc. Three simulation displays are provided for both the radar and echo sounder.

The simulation icon (SIM) appears when any simulation mode is active.

To start the simulation display;

1. Press the MENU key.

2. Press the SYSTEM CONFIGURATION, SYSTEM SETUP and SIMULATION SETUP soft keys in that order.

SIM

RADAR LIVE

PLOTTER LIVE

SOUNDER LIVE

SPEED 00.0kt

00.000'W

COURSE 000.0

LATITUDE 45°35.000'N

LONGITUDE 125

START DATE & TIME 00:00 01.APR.00

GET RADAR SIMULATION DATA

SETUP

EDIT

RETURN

Simulation setup menu

3. Follow appropriate procedure on the next several pages. To stop the simulation mode and return to normal operation, choose LIVE for radar, sounder or plotter.

Radar

NavNet display unit-generated echoes or user data

1. Select RADAR, then press the EDIT soft key.

RADAR

▲



BUILT IN DATA 1



BUILT IN DATA 2



USER DATA



LIVE

▼

2. Select BUILT IN DATA 1 or 2 for internally generated echoes or USER DATA for user-saved radar data. Push the ENTER knob.

3. Press the MENU key to close the menu.

1-15

1. OPERATIONAL OVERVIEW

NavNet radar antenna-generated echoes (not available with the GD-1920C)

1. Select GET RADAR SIMULATION DATA, then press the EDIT soft key.

2. Select YES, then push the ENTER knob to erase simulation data and get new data. The message “Now getting demo data. Do not turn off display unit.” appears while the unit is receiving radar data.

Note: If the network radar could not be found “Radar source is not found. Cannot get

demo data.” appears. And if the radar is not active, the message “Radar is not active. Cannot get demo data.” is displayed. Check that the radar is plugged in and its signal cable is firmly fastened.

3. Select RADAR, then press the EDIT soft key.

4. Select SIMULATION 2, then push the ENTER knob.

5. Press the MENU key to close the menu.

Plotter

1. Select PLOTTER, then press the EDIT soft key.

2. Select SIMULATION, then push the ENTER knob.

3. Select SPEED, then press the EDIT soft key.

4. Enter speed (setting range, 0-99 kt, default speed, 0 kt) with the alphanumeric keys, then push the ENTER knob.

PLOTTER

▲



 SIMULATION  LIVE

▼

5. Select COURSE, then press the EDIT soft key.

6. Select “8 FIGURE” to trace the simulated ship’s track in a figure-eight course, or enter your own course at DIRECTION. To enter course, use the Trackball to select digit, and enter value with the alphanumeric keys.

7. Press the ENTER soft key.

8. Select LATITUDE, then press the EDIT soft key.

9. Enter latitude (setting range, 85

N-85°S, default setting, 45°35.000’N), then push the

ENTER knob.

10. Select LONGITUDE, then press the EDIT soft key.

11. Enter longitude (setting range, 180

E-180°W, default setting, 125°00.000’W), then push

the ENTER knob.

12. Select START DATE & TIME, then press the EDIT soft key.

13. Enter start date and time, then push the ENTER knob.

14. Press the MENU key to close the menu.

Sounder

1. Select SOUNDER, then press the EDIT soft key.

2. Select BUILT IN DATA (internally generated echoes) or ETR (network sounder-generated echoes), then push the ENTER knob.

Note: The depth, shift, bottom-zoom, bottom-lock and

bottom discrimination cannot be shown in the BUILT IN DATA mode.

3. Press the MENU key to close the menu.

1-16

SOUNDER

▲



BUILT IN DATA



ETR DATA



LIVE

▼

2. RADAR OPERATION

This chapter covers radar operation, including the ARP (Auto Plotter) function. ARP requires a Model 18x4C/19x4C series network radar equipped with the ARP circuit board.

2.1 Radar Display

North marker (Head-up, Course-up mode)

Range/ range ring interval

Presentation mode

Alarm icon

EBL1

Battery icon

Simulation mode

Guard zone 1

Range ring

VRM1

Zoom area

EBL1 bearing

VRM1 range

Pulselength

3nm

12/

H-UP

S I M

EBL1

27.0°R VRM1

5.666nm

Guard zone 2

Cursor

Heading line

EBL2

327.1°R VRM2

8.212nm

EBL2 bearing, VRM2 range

319. 9

Heading M: Magnetic T: True

°M

TRAIL 30m

11.70

02m30s

G1 IN

G2 OUT

ES H

EAV L

IR L

359.9 °R

Trail time Trail elapsed time

Guard zone 1 Guard zone 2

Echo stretch

Echo averaging

Interference rejector

VRM2

EBL2

Own ship vector (ARP-equipped model, true vector mode)

Zoom window

Cursor range and bearing (Cursor position may also be shown, in L/L or Loran C TD.)

Radar display

2.2 Transmitting, Stand-by

1. Confirm that the network radar is plugged in.

2. Press the DISP key to select a radar display.

3. Press the POWER/BRILL key momentarily.

4. Press the RADAR STBY soft key to highlight TX on its label.

5. Press the RETURN soft key.

When the radar picture is not required, but you want keep it in a state of readiness, press the RADAR TX soft key to highlight STBY on its label.

2-1

2. RADAR OPERATION

2.3 Tuning

The radar receiver can be tuned automatically or manually, and the default tu ning method is automatic. If you require manual tuning, do the following:

1. Press the MENU key to display the main menu.

2. Press the RADAR DISPLAY SETUP soft key.

3. Select TUNING, then press the EDIT soft key.

TUNING



AUTO



MAN

Tuning window

4. Choose MAN.

5. Adjust the ENTER knob until the tuning bar is at its longest position.

6. Press the MENU key to close the menu.

Note: If the auto setting does not provide satisfactory tuning, ask your dealer how to re-adjust tuning.

Tuning bar

2.4 Adjusting the Gain

The GAIN key adjusts the gain sensitivity of the radar receiver. It works in a manner similar to that of volume control of a broadcast receiver, which amplifies received signals.

The proper setting is such that the background noise is just visible on the screen. If your gain setting is too low, weak echoes may be missed. On the other hand, excessive gain yields too much background noise; strong targets may b e missed because of the poor contrast between desired echoes and the backgroun d noise on the display.

To adjust the receiver sensitivity, transmit on long range, and then do the following:

1. Press the GAIN key to show the “gain adjustment” soft keys, and the last-used adjustment window appears. The example below shows the gain sensitivity adjustment window. The gain soft keys shown depend on radar source as shown below.

2. If the gain sensitivity window is not displayed, press the GAIN soft key to show the gain sensitivity setting window.

3. Use the Trackball to select AUTO ROUGH, AUTO MODERATE, AUTO CALM, or MAN (manual) as appropriate. Select an AUTO option according to the sea state.

4. For manual adjustment, rotate the ENTER knob to adjust, while observing the radar echo. The range of adjustment is 0-100.

5. Press the GAIN key on the front panel or the RETURN soft key to finish.

GAIN SENSITIVITY



AUTO ROUGH



AUTO MODERATE



AUTO CALM



MAN

Gain sensitivity window

2-2

2. RADAR OPERATION

Adjusting the FTC (When the radar source is the 17x4 series radar)

To suppress rain clutter from heavy storms or scattered rain clutter, adjust the FTC. In addition to reducing clutter, the FTC can be used in fine weather to clarify the picture when navigating in confined waters. However, with the circuit active the receiver is less sensitive. Therefore, turn off the FTC, by setting it for “0”, when its function is not required.

1. Press the GAIN key.

2. Press the FTC soft key to show the FTC window.

3. Rotate the ENTER knob to adjust. The range of adjustment is 0-100(%). Do not overadjust the FTC – weak target echoes may be missed.

4. Press the GAIN key on the front panel or RETURN soft key to finish.

2.5 Reducing Sea Clutter

2.5.1 How the A/C SEA works

Echoes from waves can be troublesome, covering the central part of the display with random signals known as “sea clutter”. The higher the waves and the higher the antenna above the water, the further the clutter will extend. Sea clutter may affect radar performance because real targets are sometimes hidden by the echoes of small waves. (See the left-hand figure in the figure below.) When sea clutter masks the picture, adjust the A/C SEA to reduce the clutter.

The A/C SEA reduces the amplification of echoes at short ranges (where clutter is the greatest) and progressively increases amplification as the range increases, so amplification will be normal at those ranges where there is no sea clutter.

Sea clutter at

screen center

Effect of A/C SEA

A/C SEA adjusted;

sea clutter suppressed

2-3

2. RADAR OPE RATION

2.5.2 Adjusting the A/C SEA

A/C SEA should be adjusted so that the clutter is broken up into small dots, and small targets become distinguishable.

1. Press the GAIN key.

2. Press the A/C SEA soft key to show the A/C SEA setting window.

A/C SEA

AUTO ROUGH

AUTO MODERATE

AUTO CALM

MAN

A/C SEA setting window

3. Use the Trackball to select AUTO ROUGH, AUTO MODERATE, AUTO CALM, or MAN (manual) as appropriate. Select an AUTO option according t o t he sea state.

4. For manual adjustment , rot ate the ENTER knob to adjust. The range of adjustment is 0-100. Do not overadjust – weak echoes may be missed.

5. When the radar source is th e Model 18x4 or 19x4, A/C SEA and A/C RAIN can be automatically adjusted, with the A/C AUTO O N/OFF soft key. Press the key to highlight ON or OFF as appropriate. Note that A/C AUTO adjustment is done at MAN indicator in the A/C SEA window.

6. Press the GAIN key on the front panel or RETURN soft key to finish.

2.6 Reducing Precipitation Clutter

The vertical beamwidth of the ant enna is designed to see surface targets even when the ship is rolling. However, by this design the unit will also det ect precipitation clutter (rain, snow, hail, etc.) in the same manner as normal targets. Precipit ation clutter shows as random dots on the screen.

2.6.1 Adjusting the A/C RAIN

When echoes from precipitation m ask solid targets, adjust the A/C RAIN to split up these unwanted echoes into a speckled pattern, making recogniti on of solid targets easier.

1. Press the GAIN key.

2. Press the A/C RAIN soft key to show the A/C RAIN window.

A/C RAIN

A/C RAIN setting window

3. Rotate the ENTER knob to adjust the A/C RAIN. The current level is shown on the A/C RAIN level bar in the A/C RAIN window, and the range of adjustment is 0 to 100(%). Do not overadjust – weak echoes may be missed.

4. Press the GAIN key on the front panel or RETURN soft key to finish.

2-4

2. RADAR OPERATION

2.7 Range Scale

The range set ting determines t he size of the area (in nautical mil es ) that will appear on your display. In addition, the range s et ting will also automatically adjust the range ring i nterval so that accurate r ange measurements may be made w hile operating on any range setting.

The range, r ange ring interval and pulselength a ppear at the top lef t-hand corner of the display.

Press the [RANGE (+ or -)] key to change the range scale.

Range scales (nm, sm)

Range 0.125 0.25 0.5 0.75 1 1.5 2 3 4 6 8 12 16 24 36 48 64 72 Ring

Interval No. of

Rings

Range 0.25 0.5 0.75 1 1.5 2 3 4 6 8 12 16 24 36 48 64 72 Ring Interval 0.125 0.25 0.25 0.25 0.5 0.5 1 1 2 2 3 4 6 12 12 16 18 No. of Rings 2 2 4 5 4 5 4 5 4 5 5 5 5 4 5 5 5

0.0625 0.125 0.125 0.25 0.25 0.5 0.5 1 1 2 2 3 4 6 12 12 16 18

2 2 5 4 5 4 5 4 5 4 5 5 5 5 4 5 5 5

Range scales ( km)

Note 1: Max imum range depends on t he network radar as shown below.

Model 1824C: 24 nm Model 1834C: 36 nm Model 1934C: 48 nm Model 1944C: 64 nm Model 1954C, 1964C: 72 nm

Note 2: You m ay choose which r anges to use from the RADAR RANGE SET UP m enu. For details s ee paragraph 7.2.2. This function is not avai lable with the G D- 1920C.

2.8 Pulselength

The puls elength in use is displayed at the upper l eft corner of the displ ay. Appropriate pulselengt hs are preset to individual range scal es . Therefore, you are not usually required to select t hem . If you are not satisfied with the current pulselength set ting, however, it is possible to change it for the ranges s hown below. Generally, select a longer pulse for longer detect ion range and shor ter pulse for better r ange discrimination.

1.5 nm, 1.5 sm, 3 km: Short pulse, medium pulse 3 nm, 3 sm, 6 km: Medium pulse, long pulse

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the SIGNAL PROC. soft key.

2-5

2. RADAR OPERATION

1nm

H-UP

319. 9

°M

SIGNAL PROCESS

I. REJ

OFF

E. AVG

OFF

PULSE

MED

E. STR

OFF

RETURN

359.9 °R

11.70

Shown when radar source is the Model 18x4/19x4 series radar. Not shown otherwise.

Signal process soft keys

3. Choose the 1.5 nm or 3 nm with the RANGE key.

4. Press the PULSE soft key to select the pulselength setting. SHORT or MEDIUM for 1.5 nm, 1.5 sm, 3 km and MEDIUM or LONG for 3 nm, 3 sm, 6 km.

5. Press the RETURN soft key to finish.

2.9 Presentation Mode

This unit provides four radar presentation modes: head-up, course-up, north-up and true motion.

Heading data is required for modes other than head-up.

2.9.1 Selecting a presentation mode

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the RADAR DISPLY soft key to show the RADAR DISPLAY soft keys.

3. Press the MODE soft key. Each pressing of the key changes the presentation mode and the presentation mode indication in the sequen ce of North-up, True Motion, Head-up, and Course-up.

Function Indicator on display Soft key label

North-up N-UP NTH UP True Motion TR-M TRUE M Head-up H-UP HD UP Course-up C-UP CSE UP

4. Press the RETURN soft key to finish.

Note: When heading data is lost, the presentation mode automatically goes to h ead-up, the heading indication at the screen top shows “- - -.-°” and the audio alarm sounds. Press the ALARM key to acknowledge the alarm. The message “HEADING DATA MISSING” appears. Restore compass signal to show heading indication. Use t he MODE soft key to select presentation mode if necessary. The audio alarm may be silenced with the CLEAR key.

2-6

2.9.2 Description of presentation modes

2. RADAR OPERATION

Head-up

A display without azimuth stabilization in which the line connecting the center with the top of the display indicates own ship’s heading. Targets are painted at their measured distances and in their directions relative to own ship’s heading.

The short line on the bearing scale is the north marker.

Course-up

The radar picture is stabilized and displayed with the currently selected course at the top of the screen. As you change heading, the ship’s heading line moves. If you select a new course, the picture resets to display the new course at the top of the display.

Targets are painted at their measured distances and in their directions relative to the intended course which is maintained at the 0-degree position. The heading line moves in accordance with ship’s yawing and course changes.

North-up

North Marker

NorthMarker

Head-up display

Course-up display

North

Heading Line

HeadingLine

In the north-up mode, targets are painted at their measured distances and in their true (compass) directions from own ship. North is maintained at the top of the screen. The heading line changes its direction according to ship’s heading.

T rue motion

Fixed radar targets maintain a constant position on the screen, while your own ship moves across the radar image at the correct speed and heading. A map-like image is displayed, with all moving vessels traveling in true perspective to each other and to fixed landmasses. As your ship’s position approaches the edge of the screen, the radar display is automatically reset to reveal the area ahead of your ship. You can manually reset your ship’s position at any time by pressing the RADAR DISPLY soft key followed by the SHIFT soft key.

North-up display

North

Heading Line

True motion display

2-7

2. RADAR OPERATION

2.10 Measuring the Range

You can measure the range to a radar target three ways: by the range rings, by the cursor, and by the VRM (Variable Range Marker).

2.10.1 Measuring range by range rings

Count the number of rings between the center of the display and the target. Check the range ring interval and judge the distance of the echo from the inner edge of the near est ring.

To turn the range rings on, do the following:

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the RADAR DISPLY soft key.

3. Press the RINGS soft key to turn the rings on and select desired brilliance.

4. Press the RETURN soft key to finish.

2.10.2 Measuring range by cursor

Operate the Trackball to place the cursor intersection on the inside edge of the radar target. The range to the target, as well as the bearing, appears to the right of “+” at the bo ttom of the display.

Cursor

Target

3nm

12/

H-UP

319. 9

°M

SIGNAL PROC.

RADAR DISPLY

NAV FUNC

TARGET

ZOOM & D. BOX

11.2 °R

11.70

2-8

Range and bearing from

own ship to cursor

How to measure range to a target with the cursor

2. RADAR OPERATION

2.10.3 Measuring range by VRM

1. Press the EBL/VRM key to display the EBL/VRM soft keys.

2. Press the VRM1 ON (dotted ring VRM) or VRM2 ON (dashed ring VRM) soft key to select the desired VRM. The selected VRM’s indication, at the bottom of the screen, is highlighted.

3. Rotate the ENTER knob then place the VRM on the inside edge of a radar target. Read the VRM indication to find range to the target.

VRM2

(Dashed line)

VRM1

(Dotted line)

VRM1 range

3nm

12/

H-UP

EBL1

---.-°R VRM1

3.123nm

EBL2

---.-°R VRM2

9.343nm

Active VRM is highlighted.

VRM2 range

319. 9

EBL VRM

EBL1 ON

VRM1 ON

OFFSET

EBL2 ON

VRM2 ON

11.70

359.9 °R

How to measure range with the VRM

4. You may hide the EBL/VRM soft keys by pressing the EBL/VRM key.

2.10.4 Various VRM operations

Erasing a VRM, VRM indication: Press appropriate VRM soft key, then press the CLEAR

key. The VRM is erased and its indication becomes blank.

Erasing EBL/VRM data boxes: Press the EBL or VRM soft key associated with the EBL/VRM data box you wish to erase. Press the CLEAR key once or twice to erase the data box.

Hiding EBL/VRM data boxes: Press the ZOOM & D. BOX and D. BOX ON/OFF soft keys to show or hide the EBL/VRM data boxes.

Moving EBL/VRM data boxes: When an EBL/VRM data box is obscuring a target you want to see, you can move it to another location as shown below. This cannot be done when the EBL/VRM soft keys are shown.

1. Press the EBL/VRM key to turn off the EBL/VRM soft keys.

2. Using the Trackball, place the cursor inside the data box you wish to move. As the cursor enters the box it changes to a “hand.” Push the ENTER knob, and the hand changes to a fist, meaning the box is correctly selected.

3. Use the Trackball to move the data box to the location desired, then push the ENTER knob.

2-9

2. RADAR OPERATION

2.11 Measuring the Bearing

There are two ways to measure the bearing to a target: by the cursor, and by the EBL (Electronic bearing Line).

2.11.1 Measuring bearing by cursor

Use the Trackball to place the cursor at the center of the target. The bearing to the target appears in the range and bearing box at the bottom right-h and corner on the screen.

2.11.2 Measuring bearing by EBL

1. Press the EBL/VRM key.

2. Press the EBL1 ON (dotted line EBL) or EBL2 ON (dashed line EBL) soft key to select the desired EBL. The selected EBL’s indication, at the bottom of the screen, is highlighted.

3. Rotate the ENTER knob to bisect the radar target with the EBL. Read the EBL indication to find the bearing to the target.

EBL1

(Dotted line)

EBL2

(Dashed line)

EBL2 bearing

EBL1 bearing

3nm

12/

H-UP

EBL1

330.1°R VRM1

-.---nm

EBL2

234.1°R VRM2

-.---nm

319. 9

Active marker is highlighted.

EBL

°M

VRM

EBL1 ON

VRM1 ON

OFFSET

EBL2 ON

VRM2 ON

359.9 °R

11.70

How to measure bearing with the EBL

4. You may hide the EBL/VRM soft keys by pressing the EBL/VRM key.

Note: The bearing to a target may be shown relative to own ship’s head ing (Relative) or

True bearing (requires heading data). This may be done with “EBL REFERENCE,” which is in the RADAR DISPLAY SETUP menu.

2.11.3 Various EBL operations

Erasing an EBL, EBL indication: Press appropriate EBL soft key, then press the CLEAR

key. The EBL is erased and its indication becomes blank.

Erasing, hiding, moving EBL/VRM data boxes: See paragraph 2.10.4.

2-10

2. RADAR OPERATION

2.12 Erasing the Heading Line, North Marker

The heading line indicates the ship's heading in all presentation modes. It is a line from the own ship position to the outer edge of the radar display area and appears at zero degrees on the bearing scale in head-up mode; it changes its orientation in the north-up, course-up and true motion modes with ship’s movement.

The north marker appears as a short dashed line. In the head-up and course-up modes the north marker moves around the bearing scale as the ship’s heading mo ves.

To temporarily erase the heading line and north marker, press the RADAR DISPLY soft key followed by the HL OFF soft key. Release the key to redisplay the markers. (If the radar soft keys are not shown, hit the CLEAR key to display them.)

2.13 Reducing Noise Interference

Noise, appearing on the displays as random “speckles,” can be reduced as follows:

1. Press the MENU key to open the menu.

2. Press the RADAR DISPLAY SETUP soft key.

3. Select NOISE REJECTION, then press the EDIT soft key.

4. Select OFF, LOW or HIGH as appropriate.

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

2.14 Rejecting Radar Interference

Radar interference may occur when near another shipborne radar that is op erating in the same frequency band as your radar. Its on-screen appearance looks like m any bright dots either scattered at random or in the form of dotted lines extending from the center to the edge of the display. Interference effects are distinguishab le from normal echoes because they do not appear in the same place on successive rotations of the scanner.

Be sure to turn off the interference rejector when no interference exists – weak targets may be missed.

Radar interference

2-11

2. RADAR OPERATION

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the SIGNAL PROC. soft key.

1nm

H-UP

319. 9

°M

SIGNAL PROCESS

I. REJ

OFF

E. AVG

OFF

PULSE

MED

E. STR

OFF

RETURN

359.9 °R

11.70

Shown when radar source is the Model 18x4/19x4 series radar. Not shown otherwise.

SIGNAL PROCESS soft keys

3. Press the I. REJ soft key successively to choose the interference rejection level desired; LOW, MED, HIGH or OFF.

4. Press the RETURN soft key to finish.

The display shows IR L (Low), IR M (Medium) or IR H (High) when the interference rejector is on.

2.15 Zoom

The zoom feature allows you to double the size of the area selected with the “zoom square.” It is available on any range but is inoperative in true motion and when the display is shifted.

2.15.1 Zooming radar targets

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Use the Trackball to set the cursor where you want to zoom.

3. Press the ZOOM & D. BOX soft key to show ZOOM & D. BOX soft keys.

4. Press the ZOOM ON/OFF soft key to select ON. A hollow square, called the “zoom area,” appears on the display.

5. To release the cursor, press the CURSOR FLOAT soft key. (The hollow square changes to a dashed one.) To relocate the zoom circle, select location with the Trackball, then press the CURSOR LOCK key.

6. To quit the zoom function, press the ZOOM ON/OFF soft key to select OFF.

2-12

2. RADAR OPERATION

Zoom area

3nm

12/

Zoom window

319. 9

ZOOM & D. BOX

ZOOM

ON /OFF

CURSOR

ARP TGT ZM

D. BOX ON/ OFF

RETURN

5.727

FLOAT

Requires optional ARP Board in Model 18x4/19x4 series network radar. Not shown otherwise.

359.9 °R

Zoom

2.15.2 Zooming ARP, TTM targets

You may z oom in on TTM (Tracked T ar get Message) and ARP targets. TTM t ar gets can come from a Na vNet connected radar, or from other ARP r adar that is outputting the TTM message. ( T TM is a NMEA 0183 data sent ence that i s an avai lable output from som e A RP capable radar .) Target numbers must be turned on t o us e t his function. This can be done by enabling the target ID number option in the ARP SETUP menu. This func tion is available when TARGET ID NUMBER is ON.

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the ZOOM/D. BOX soft key to show ZOOM & D. BOX soft keys.

3. Press the ZOOM ON/OFF soft key to select ZOOM ON.

4. Press the ARP TGT ZM soft key.

SELECT TARGET NO.

▲

▼

Target no. se lec tion window

5. Use the EN TER kn ob to select number ( 1- 10), then push the ENTER knob. If the target number does n ot exist several beeps sound and the zoom function is cancelled.

. To cancel, press the CURSOR LO CK s oft key.

Note: T he z oom window blends in with the background when the background color for the radar picture is white. If the window is diffic ult to see, change the back gr ound color.

2-13

2. RADAR OPERATION

2.16 Shifting the Picture

Own shi p pos ition, or sweep origin, can be displaced manually or automatically t o ex pand the view field without swit c hing to a larger scale. Z oom is not available when the display is shifted.

2.16.1 Manual shift

The sw eep or igin can be shift ed in any presentation mode to a point specified by the cursor by up to 50% of the range in us e in any direction.

1. Locate the cursor anyw her e within the effect ive radius of the display.

2. If not displayed, press the

Place cursor where desired.

Press the MANUAL soft key.

Cursor

HIDE/SHOW key to show the radar soft keys.

3. Press the RADAR DISPLY soft key.

4. Press the SHIFT soft key.

5. Press the MANUAL soft key to shift. The heading line shifts to the cur sor location. SHIFT appears at right-hand corner of the display.

To cancel shift, press the RADAR DISPLY, SHIFT and OFF soft keys.

2.16.2 Automatic shift

SHIFT

The amount of automatic shi ft is calculated according to ship’s speed, and the amount of shift is limited to 50% of the r ange in use.

Ship's speed Shift speed setting

X 0.5 = Amount of shift(%)

For example, if you set the shi ft s peed setting for 15 knots and the ship is running at 10 knots the amount of shift will be about 34%. The form ula for determining shift amount is as shown below. Automatic shift mode i s only available in the head-up mode.

Setting au t omatic shift maximum speed

1. If not displayed, press the HIDE/SHOW key to show the radar sof t keys.

2. Press the RADAR DISPLY soft key.

3. Press the SHIFT soft key to show the shift soft keys.

4. Press the AUTO S.SPD sof t key t o display the auto ship speed sett ing window.

5. Adjust the Trackball or ENTER knob to set the

AUTO SHIP SPEED

maximum speed of your vessel, and then push the ENTER knob or the ENTER soft key to set. The setting range is 1- 99 k t and the default setting is 15 kt.

Automatic shift

Press the AUTO soft key. T o c anc el shift, press the RADAR DISPLY, S HIFT and OFF soft keys.

2-14

2. RADAR OPERATION

2.17 Using the Offset EBL

The offset EBL can be used to predict a potential collision course. It can also be used to measure the range and bearing between two targets.

2.17.1 Predicting collision course

The procedure below may be used to check if a radar target is on a potential collision course with your vessel.

1. Press the EBL/VRM key to show the EBL/VRM soft keys.

2. Press the EBL1 ON soft key to turn on the EBL1.

3. Press the OFFSET soft key. The origin of EBL1 moves to the cursor position, which is marked with an “X.”

4. Use the Trackball to place the cursor on the radar target which looks like it m ight be on a collision course with own ship.

5. Push the ENTER knob to fix the origin position.

6. After waiting for a few minutes (at least three minutes), rotate the ENTER knob so the EBL bisects the target at the new position. If the target tracks along the EBL towards the center of the display (your ship’s position), the target may be on a collision course with your vessel.

To cancel the offset EBL, press the OFFSET soft key.

Target tracked here

Initial target position

Predicting collision course with the offset EBL

3nm

12/

H-UP

EBL1

45.0°R VRM1

-.---nm

319. 9

VRM

EBL1 ON

VRM1 ON

OFFSET

EBL2 ON

VRM2 ON

359.9 °R

11.70

EBL

°M

2-15

2. RADAR OPERATION

2.17.2 Measuring range & bearing between two targets

The procedure which follows shows how to measure the range and bearing between two targets, using the targets “A” and “B” in the figure below as an example.

1. Operate the Trackball to place the cursor on the target “A.”

2. Press the EBL/VRM key to show the EBL/VRM soft keys.

3. Press the EBL1 ON soft key to turn on the EBL1.

4. Press the OFFSET soft key. The origin of EBL1 moves to the cursor position, which is marked with an “X.”

5. Rotate the ENTER knob so the EBL bisects the target “B.”

6. Push the ENTER knob, then press the VRM1 ON soft key.

7. Rotate the ENTER knob to place the VRM1 on the inner edge of the target “B.”

8. Look at the indications for VRM1 and EBL1 to find the range and bearing between the two targets.

To cancel the offset EBL, press the OFFSET soft key.

Target B

Target A

Bearing and range between target A and target B

3nm

12/

H-UP

EBL1

45.0°R VRM1

7.121nm

319. 9

°M

EBL VRM

EBL1 ON

VRM1 ON

OFFSET

EBL2 ON

VRM2 ON

359.9 °R

11.70

Measuring range and bearing between two targets

2-16

2. RADAR OPERATION

2.18 Echo Trails

Echo trails are simulated afterglow of target echoes that represent their movements relative or true to own ship. This function is useful for alerting you past possible collision situations.

Echo trail

Sample echo trails

2.18.1 Trail time

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the TARGET soft key.

3. Press the TRAIL soft key to show the trail soft keys.

3nm

12/

H-UP

319. 9

TRAIL

ON /OFF

TRAIL TIME

GRAD

SINGLE

TRAIL COLOR

RETURN

359.9 °R

11.70

Trail soft keys

4. Press the TRAIL TIME soft key to show the trail time window.

TRAIL TIME

▲



15 seconds



30 seconds



1 minute



3 minutes



6 minutes



15 minutes



30 minutes



CONTINUOUS

▼

Trail time window

5. Use the Trackball to select time desired.

6. Press the ENTER soft key.

7. Press the RETURN soft key twice to finish.

2-17

2. RADAR OPERATION

2.18.2 Starting echo trails

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the TARGET soft key.

3. Press the TRAIL soft key.

4. Press the TRAIL ON/OFF soft key to select ON.

5. Press the RETURN soft key twice to finish.

“TRAIL,” the echo trail time selected and elaps ed time appear at the top right-hand corner of the display. Then, afterglow starts exten ding from all targets. Trails are restarted when the range or mode is changed and zoom or shift is turned on.

For continuous trails, the maximum cont inuous trail time is 99 minutes and 59 seconds. When the elapsed time clock counts up to that time, the elapsed time display resets to zero and trails begin again.

To turn off echo trail, press the TRAIL ON/OFF soft key to select OFF at step 4 in the above procedure.

Trails are restarted when the range or mode is changed and zoom or shift is activated.

2.18.3 Trail gradation

The echo trails can be shown in single or multiple gradations. Multiple gradation paints the trails thinner with time, like the afterglow on an analog PPI radar.

1. If not displayed, press the HIDE/SHOW soft key to show the radar soft keys.

2. Press the TARGET and TRAIL soft keys.

3. Press the GRAD soft key to select SINGLE or MULTI as appropriate.

4. Press the RETURN soft key twice to finish.

Multitone Monotone

Multitone and monotone trails

2.18.4 Trail color

Trails may be shown target trails in blue, yellow, green or white.

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the TARGET, TRAIL and TRAIL COLOR soft keys in that order.

TRAIL COLOR

BLUE YELLOW GREEN WHITE

Trail color window

3. Use the Trackball to select the color desired, then press the ENTER soft key.

4. Press the RETURN soft key twice.

2-18

2. RADAR OPERATION

2.18.5 Echo trail mode

Echo trails can be shown in Relative or True motion. (True trails require he ading and speed inputs.)

1. Press the MENU key.

2. Press the RADAR DISPLAY SETUP key.

3. Choose TRAIL MODE, then press the EDIT soft key.

TRAIL MODE

▲



TRUE



RELATIVE

▼

Trail mode window

4. Select TRUE or RELATIVE as appropriate, then press the ENTER soft key.

5. Press the MENU key to close the menu.

2.19 Echo Stretch

Normally, the reflected echoes from long range targets appea r on the display as weaker and smaller blips even though they are compensated by the radar’s internal circuitry. The echo stretch function magnifies these small blips in all ranges. Two types of echo stretch are available: ES LOW which stretches echoes in bearing direction an d ES HIGH which stretches them in both range and bearing directions.

Target

Range direction

Echo Stretch OFF

Bearing direction

"LOW" Echo stretch "HIGH" Echo stretch

Bearing direction

Types of echo stretch

This function magnifies not only targets but also sea clutter and radar interference. For this reason, be sure sea clutter and radar interference are properly suppressed before activating the echo stretch.

1. If not displayed, press the HIDE/SHOW key to show the radar soft keys.

2. Press the SIGNAL PROC. soft key.

3. Press the E. STR soft key to select HIGH, LOW or OFF as appropriate.

4. Press the RETURN soft key to finish.

The display shows ES H (High) or ES L (Low) when the echo stretch is on.

2-19

2. RADAR OPERATION

2.20 Echo Averaging

The echo average feature, which requires a Model 18x4/19x4 series network radar, effectively suppresses sea clutter. Echoes received from stable targets such as ships appear on the screen at almost the same position during every rotation of the antenna. On the other hand, unstable echoes such as sea clutter appear at random pos itions.

To distinguish real target echoes from sea clutter, echo average performs scan-to -scan correlation. Correlation is made by storing and averaging echo signals over successive picture frames. If an echo is solid and stable, it is presented in its normal intensity. Sea clutter is averaged over successive scans resulting in the reduced brilliance, making it easier to discriminate real targets from sea clutter.

To properly use the echo average function, it is recommended to first supp ress sea clutter with the A/C SEA control and then do the following:

1. If not displayed, press the HIDE/SHOW key to display the radar soft keys.

2. Press the SIGNAL PROC. soft key.

3. Press the E. AVG soft key to select desired echo averaging. OFF: No averaging LOW: Helps distinguish targets from sea clutter and suppresses brilliance of unstable echoes. MED: Distinguishes small stationary targets such as navigation buoys.

HIGH: Stably displays distant targets.

4. Press the RETURN soft key to finish.

The display shows EAV L, EAV M or EAV H when echo averaging is on.

2-20

(a) Echo average OFF (b) Echo average ON

Effect of echo averaging

2. RADAR OPERATION

2.21 Outputting TLL Data

Target position data can be output to units of the network and shown on their plot ter screen with the TLL mark (X). This function requires position and heading data.

1. Operate the Trackball to place the cursor on the target whose position you wish to output.

2. If not displayed, press the HIDE/SHOW key to display the radar soft keys.

3. Press the TARGET soft key.

3nm

12/

H-UP

319. 9

°M

TARGET

TRAIL

TLL OUTPUT

ACQ

TARGET INFO

RETURN

Requires ARP circuit board in Model 18x4/19x4 series NavNet radar. Not shown otherwise.

359.9 °R

11.70

TARGET soft keys

4. Press the TLL OUTPUT soft key to output target position data. The TLL mark appears on the plotter screen at the target’s position the moment the TLL OUTPUT soft key was pressed. Further, that position is recorded as a waypoint on all NavNet units, under the youngest empty waypoint number on each NavNet unit.

5. Press the RETURN soft key to finish.

Note: The screen of the TLL recipient may be temporarily interrupted when receiving TLL from another NavNet display unit. Press any key to restore normal operation.

2-21

2. RADAR OPERATION

2.22 Guard Alarm

The guard alarm allows the operator to set the desired range and bearing for a guard zone. When ships, islands, landmasses, etc. violate the guard zone, an audi o alarm sounds and the offending target blinks to call the operator’s attention.

CAUTION

• The alarm should not be relied upon as

the sole means for detecting possible collision situations.

• A/C SEA, A/C RAIN and GAIN controls

should be properly adjusted to be sure the alarm system does not overlook target echoes.

2.22.1 Setting a guard alarm zone

To set a guard alarm zone, set the radar to transmit and do the following:

1. Press the ALARM key.

2. Use the Trackball to set the cursor on the top left corner (or top right corner) of the guard zone you want to set, then press the SET GUARD1 or SET GUARD2 soft key, depending on which guard zone you want to set.

3. Use the Trackball to set the cursor on the bottom right corner (or top left corner) of the guard zone area, then push the ENTER knob.

4. Press the RETURN soft key to finish.

3nm

12/

H-UP

319. 9

MOVE +CURSOR TO ANOTHER CORNER OF GUARD1 AND PUSH KNOB TO SET.

(1) Drag cursor to top (or bottom) corner for guard zone and press the SET GUARD1 or SET GUARD2 soft key.

°M

ALARM

SET GUARD1

SET GUARD2

RETURN

317.2 °R

11.60

3nm

12/

H-UP

NO ALARM

319. 9

ALARM

°M

GUARD 1

SET GUARD1

ERASE GUARD1

SET GUARD2

RETURN

8.800

39.9 °R

(2) Drag cursor diagonally to bottom (or top) corner for guard zone and press the [ENTER] knob.

How to set a guard alarm zone

The equipment then searches for targets inside the guard zone to determine guard alarm type. If a target is found inside the guard zone, the guard zone type becomes an “Outwar d guard alarm,” and any target exiting the guard zone will trigger the au dio alarm. If no target is found, the guard zone type becomes an “Inward guard alarm,” and any targets entering the guard zone will trigger the audio alarm. The guard alarm type is shown as G1(G2) IN or G1(G2) OUT.

2-22

2. RADAR OPERATION

Note 1: When the radar range is less than the guard zone range “G1 (G2) IN” or “G1 (G2) OUT” changes to “G1 (G2) ***.” The guard alarm function is not available while this indication appears.

Note 2: If the network radar is set to standby while the guard alarm is active, the guard alarm is cancelled. The guard alarm is redisplayed when the radar is set to transmit again.

2.22.2 When the alarm is violated…

Any radar target violating the guard zone will flash, the audio alarm s ounds, and the alarm icon appears in red. Additionally the message “TARGET ENTERED I NTO GUARD1(GUARD2)” or “TARGET LEFT FROM GUARD1(GUARD2)” is displayed at the bottom of the screen. Press the CLEAR key to silence the alarm.

2.22.3 Cancelling the guard alarm

1. Press the ALARM key to show the ALARM menu.

2. Press the ERASE GUARD1 or ERASE GUARD2 soft key as appropriate.

3. Press the RETURN soft key to finish.

2.23 Watchman

2.23.1 How watchman works

The watchman function periodically transmits radar pulses for one minute to check for targets in a guard zone. If a target is found in the zone, watchman is cancelled, the audio alarm sounds and the radar continues transmitting. If no target is found the radar goes into standby for the number of minutes specified on the RADAR DISPLAY SETUP me nu. This feature is useful when you do not need the radar’s function continuously but want to be alerted to radar targets in a specific area. “WTCH” appears at the top left corner when Watchman is active.

1 min

Watchman starts

ST-BY

5,10 or 20 min

* Beeps emitted just before radar transmits.

1 min

ST-BY

5,10 or 20 min

How watchman works

2.23.2 Turning on/off watchman

1. Set a guard zone. (See the paragraph 2.22.)

2. If not displayed, press the HIDE/SHOW key to display the radar soft keys.

3. Press the NAV FUNC soft key.

4. Press the W. MAN ON/OFF soft key to select ON or OFF as appropriate.

5. Press the RETURN soft key to finish.

2-23

2. RADAR OPERATION

Note: When the watchman is activated and no guard zone is active, the message “PLEASE SET GUARD ZONE. PUSH ANY KEY TO CONTINUE.” appears. Press any key and then set a guard zone.

2.23.3 Setting watchman stand-by interval

The watchman standby interval, that is, the number of minutes the radar is in standby, can be set to 5, 10 or 20 minutes as follows:

1. Press the MENU key.

2. Press the RADAR DISPLAY SETUP soft key.

3. Select WATCHMAN TIME, then press the EDIT soft key.

WATCHMAN TIME





5 minutes



10 minutes



20 minutes

Watchman time window

4. Select time desired, then press the ENTER soft key.

5. Press the MENU key to close the menu.

2.24 Suppressing Second-trace Echoes

In certain situations, echoes from very distance targets may appear as false echoes (second-trace echoes) on the screen. This occurs when the return echo is received one transmission cycle later, or after a next radar pulse has been transmitted.

Tx repetition

Actual range

Second-trace echoes

Second-trace echo

False echo range

To activate or deactivate the second-trace echo rejector do the following:

1. Press the MENU key.

2. Press the RADAR DISPLAY SETUP soft key.

3. Use the Trackball to select 2ND ECHO REJECTION, then press the EDIT soft key.

4. Choose ON or OFF as appropriate, then press the ENTER soft key.

5. Press the MENU key to close the menu.

2-24

2. RADAR OPERATION

2.25 Waypoint Marker

A waypoint marker, showing the location of the destination waypoint set on the plotter, may be inscribed on the radar display.

L 3nm

12/

Waypoint marker

319. 9

RETURN

NAV FUNC

W. MAN ON/ OFF

WPT MK

ON /OFF

359.9 °R

11.70

Waypoint marker

1. If not already shown, press the HIDE/SHOW key to display the radar soft keys.

2. Press the NAV FUNC soft key.

3. Press the WPT MK ON/OFF soft key to select ON or OFF as appropriate.

4. Press the RETURN soft key to finish.

2-25

2. RADAR OPERATION

2.26 ARP, TTM Operation

When the radar source is an ARP-equipped Model 18x4/19x4 series network radar, you can manually and automatically acquire and track ten targets. Once a target is acquired automatically or manually it is automatically tracked within 0.1 to 16 nm. If the FURUNO heading sensor PG-1000 is used, the data sentence “RMC” is necessary.

Alternatively, you can display the tracks of other ships by receiving the data sentence TTM (Tracked Target Message) via the NETWORK or NMEA port on the display unit. However, targets cannot be acquired.

Note: When using your unit as remote display, you cannot change the range of the main radar at the remote display. For the target acquisition, set the range individually.

Usage precautions for ARP

CAUTION

No one navigational aid should be relied upon for the safety of vessel and crew. The navigator has the responsibility to check all aids available to confirm position. Electronic aids are not a substitute for basic navigational principles and common sense.

• This auto plotter automatically tracks an automatically or manually acquired radar target and calculates its course and speed, indicating them by a vector. Since the data generated by the auto plotter are based on what radar targets are selected, the radar must always be optimally tuned for use with the auto plotter, to ensure required targets will not be lost or unwanted targets such as sea returns and noise will not be acquired and tracked.

• A target does not always mean a land mass, reef, ships or other surface vessels but can imply returns from sea surface and clutter. As the level of clutter changes with environment, the operator should properly adjust the A/C SEA, A/C RAIN and GAIN controls to be sure target echoes are not eliminated from the radar screen.

CAUTION

The plotting accuracy and response of this auto plotter meets IMO standards. Tracking accuracy is affected by the following:

• Tracking accuracy is affected by course change. One to two minutes is required to restore vectors to full accuracy after an abrupt course change. (The actual amount depends on gyrocompass specifications.)

• The amount of tracking delay is inversely proportional to the relative speed of the target. Delay is on the order of 15-30 seconds for high relative speed; 30-60 seconds for low relative speed.

Display accuracy is affected by the following:

• Echo intensity

• Radar transmission pulsewidth

• Radar bearing error

• Gyrocompass error

• Course change (own ship or target)

2-26

2. RADAR OPERATION

2.26.1 Activating/deactivating ARP, TTM

1. Press the MENU key followed by the ARP SETUP soft key to show the ARP SETUP menu.

ARP

ARP TARGET INFO INTERNAL ARP

CANCEL ALL TARGETS NO

ARP VECTOR MODE TRUE

ARP VECTOR TIME 30 minutes

HISTORY INTERVAL OFF

CPA OFF

TCPA 30 seconds

AUTO ACQUISITION AREA OFF

TARGET ID NUMBER OFF

ARP setup menu

SETUP

EDIT

RETURN

2. Select ARP TARGET INFO, then press the EDIT soft key to show the ARP TARGET INFO window.

ARP TARGET INFO

▲

INTERNAL ARP

{

EXTERNAL ARP

{

OFF

▼

ARP TARGET INFO window

3. Select INTERNAL ARP, EXTERNAL ARP or OFF as appropriate. INTERNAL ARP: The radar source must be an ARP-equipped M odel 18x4/19x4 series

NavNet radar. Select this item also for a NavNet unit being fed ARP targets. EXTERNAL ARP: Receive TTM data sentence via NMEA or NETWORK port. Target

tracks are shown but targets cannot be acquired. OFF: Turns off the ARP or TTM display.

4. Press the ENTER soft key.

5. Press the MENU key to close the menu.

2.26.2 Acquiring and tracking targets (ARP)

Ten targets may be acquired and tracked manually and automatically. When you attempt to acquire an 11th target, the message “ARP FULL – ALREADY TRACKING 10 TARGETS!” appears for five seconds. To acquire another target, terminate tracking of an unnecessary target as shown in the paragraph “2.26.4 Terminating tracking of ARP targets.”

Manual acquisition

When the automatic acquisition (AUTO ACQ. AREA) is set to on, up to five targets may be acquired manually. If you attempt to acquire a sixth target, the alert message appears.

1. If not already shown, press the HIDE/SHOW key to show the radar soft keys.

2-27

2. RADAR OPERATION

2. Press the TARGET soft key.

3. Place the cursor on the target to acquire.

4. Press the ACQ soft key.

5. Press the RETURN soft key to finish.

The plot symbol changes over time as below. A vector appears about one m inute after acquisition, indicating the target’s motion trend.

Vector

01*

Atacquisition 1min.after

acquisition

*=TargetnumbershownwhenTARGETIDNUMBERis turnedonintheARPSETUPmenu.

01*

3min.after acquisition

01*

TargetNumber

ARP plot symbols

Note: In case of the acquisition by an external ARP, the acquisition circle mark appears one minute after acquisition.

Automatic acquisition

The ARP can acquire up to ten targets automatically by setting an automatic

Automaticacquisitionarea

acquisition area. When automatic acquisition is selected after acquiring targets manually, only the remaining capacity for targets may be

45° port

2.0-2.5nm

45° starboard

automatically acquired. For example, if seven targets have been manually acquired, three targets may be automatically acquired.

1. Press the MENU key to show the main

Automatic acquisition area

menu.

2. Press the ARP SETUP soft key to show the ARP SETUP menu.

3. Operate the Trackball to select AUTO ACQUISITION AREA.

4. Press the EDIT soft key to show the automatic acquisition area window.

AUTO ACQ. AREA

▲





OFF

▼

Automatic acquisition area window

5. Select ON, then press the ENTER soft key.

6. Press the MENU key to close the menu. An acquisition area of 2.0 to 2.5 miles in range and ±45º on either side of the heading line in bearing appears.

Note: Targets being tracked in automatic acquisition are continuously tracked when switching to manual acquisition.

2-28

2.26.3 Displaying target number (ARP, TTM)

Target number can be shown for ARP and TTM targets as below.

3nm

12/

H-UP

ARP Target Number

ARP targ et number

319. 9

°T

TARGET

TRAIL

TLL OUTPUT

ACQ

TARGET INFO

RETURN

11.70

359.9 °R

2. RADAR OPERATION

1. Press the MENU key.

2. Press the ARP SETUP soft key.

3. Select TARGET ID NUMBER.

4. Press the EDIT soft key.

5. Select ON or OFF as appropriate.

6. Press the ENTER soft key.

7. Press the MENU key to close the menu.

2.26.4 Terminating tracking of ARP targets

When ten targets have been acquired, no more acquisition occu rs unless targets are cancelled. If you need to acquire additional targets, you must first cancel one or more individual targets, or all targets, using one of the procedures below.

Terminating tracking of selected targets

1. Place the cursor on the target to terminate tracking.

2. Press the CLEAR key to terminate tracking and erase the target.

Terminating tracking of all targets

1. Press the MENU key followed by the ARP SETUP soft key.

2. Select CANCEL ALL TARGETS.

3. Press the EDIT soft key.

4. Select YES.

5. Press the ENTER soft key.

6. Press the RETURN soft key followed by the MENU key to close the menu.

CANCEL ALL TARGETS

▲



YES NO



▼

Cancel all targets window

2-29

2. RADAR OPERATION

2.26.5 Setting vector attributes (ARP)

What is a vector?

A vector is a line extending from a tracked target which shows estimated speed and co urse of the target. The vector tip shows an estimated position of the target after the selected vector time elapses. It can be useful to extend the vector length (time) in order to evaluate the risk of collision with any target.

Vector

V ector reference, vector time

You may reference the vectors to North (True, requires heading an d speed data) or ship’s heading (relative) as desired. Vector time can be set to 30 seconds, 1, 3, 6, 15 or 30 minutes.

1. Press the MENU key followed by the ARP SETUP soft key to show the ARP SETUP menu.

2. Operate the Trackball to select ARP VECTOR MODE.

3. Press the EDIT soft key to show the ARP vector mode window.

ARPVECTORMODE



RELATIVE TRUE





ARP vector mode window

4. Select TRUE or RELATIVE as appropriate.

5. Press the ENTER soft key.

6. Select ARP VECTOR TIME, then press the EDIT soft key to show the ARP vector time window.

ARP VECTOR TIME

▲



30 seconds



1 minute



3 minutes



6 minutes



15 minutes



30 minutes

▼

ARP vector time window

7. Operate the Trackball to select vector time among 30 sec, 1 min, 3 min, 6 min, 1 5 min and 30 min.

8. Press the ENTER soft key.

9. Press the MENU key to close the menu.

2-30

2. RADAR OPERATION

2.26.6 Displaying past position (ARP)

This ARP can display time-spaced dots (maximum ten dots) marking the past positions of any targets being tracked. You can evaluate a target’s actions by the spacing bet ween dots. Below are examples of dot spacing and target movement.

(a)Shipturning

(b)Shiprunning straight

(c)Shipreduced speed

(d)Shipincreased speed

Past position displays

To turn the past position display on or off:

1. Press the MENU key followed by the ARP SETUP soft key.

2. Operate the Trackball to select HISTORY INTERVAL.

3. Press the EDIT soft key to show the history interval window.

HISTORY INTERVAL

▲



OFF



30 seconds



1 minute



3 minutes



6 minutes

▼

History interval window

4. Operate the Trackball to select history interval among 30 sec, 1 min, 3 min and 6 min, or select OFF to turn off the past position display.

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

2.26.7 ARP, TTM target data

You can show motion trends (range, bearing, course, speed, CPA and TCPA) for ARP or TTM targets. Note that TARGET ID NUMBER, in the ARP SETUP menu, must be turned on to display this data.

1. Place the cursor on the target whose data you want to see.

2. If not already displayed, press the HIDE/SHOW key to show the radar soft keys.

3. Press the TARGET and TARGET INFO soft keys. The data of the selected target appears at the bottom left-hand corner of the display. (If an EBL/VRM data box is displayed the ARP (TTM) data box will be under it.)

4. Press the RETURN soft key to finish.

To erase ARP/TTM target data, select the corresponding target with the cursor, then p ress the CLEAR key.

2-31

2. RADAR OPERATION

Cursor

3nm

12/

H-UP

319. 9

°T

TARGET

TRAIL

TLL OUTPUT

ARP Target

No.01 VECTOR TRUE 15min CSE 359.9°T SPD 12.5kt CPA 2.21nm TCPA 12:35

CPA and TCPA Course and Speed Target No., Vector Reference (True), Vector Time

ACQ

TARGET INFO

RETURN

359.9 °R

11.70

ARP targ et data

2.26.8 CPA/TCPA alarm (ARP)

When the predicted CPA of any target becomes smaller than a preset CPA alarm range or its predicted TCPA less than a preset TCPA alarm limit, an audio alarm sounds a nd the speaker icon appears (in red). In addition, the target plot symbol of the offending target changes to a triangle and flashes together with its vector. You may silence the audio alarm with the CLEAR key. Press the ALARM key and the message “COL LISION ALARM” appears. Press the CLEAR ALARM soft key to acknowledge the alarm. The flashing of the triangle plot symbol continues until you intentionally terminate tracking of the target. The ARP continuously monitors the predicted range at the Closest Point of Appro ach (CPA) and predicted time to CPA (TCPA) of each track to own ship.

This feature helps alert you to targets which may be on a collision course with own ship. However, it is important that gain, A/C SEA, A/C RAIN and other radar controls are properly adjusted and the ARP is set up so that it can track targets effectively.

CPA/TCPA alarm ranges must be set up properly taking into consideration the size, tonnage, speed, turning performance and other characterist ics of own ship.

2-32

CAUTION

The CPA/TCPA alarm should never be relied upon as the sole means for detecting the risk of collision. The navigator is not relieved of the responsibility to keep visual lookout for avoiding collisions, whether or not the radar or other plotting aid is in use.

Follow the steps shown below to set the CPA/TCPA alarm range:

1. Press the MENU key followed by the ARP SETUP soft key.

2. Operate the Trackball to select CPA.

3. Press the EDIT soft key to show the CPA window.

4. Select a CP A limit desired from 0. 5 nm , 1 nm, 2 nm, 3 nm, 5 nm and 6 nm with the Trackball.

5. Press the ENTER soft key. The ARP SETUP menu reappear s .

6. Operate the Trackball t o select T CPA.

7. Press the EDIT soft key to show the TCPA window .

8. Select a TCPA limit from 30 s ec, 1 min, 2 min, 3 min, 4 mi n, 5 min, 6 min and 12 min.

9. Press the ENTER soft key.

10. Press the MENU key to close the menu.

2.26.9 Lost target alarm (ARP)

When the sy s t em detects a lost tar get, the target symbol becomes a diamond and t r ac king is discontinued after one minute.

2. RADAR OPERATION

CPA

OFF

0.5nm

{

1nm

{

2nm

{

3nm

{

5nm

{

6nm

{

CPA distance

TCPA

30 seconds

1 minute

{

2 minutes

{

3 minutes

{

4 minutes

{

5 minutes

{

6 minutes

{

12 minutes

{

TCPA time

Lost tar get mark

Canceling a lost target

1. Place the c ur s or on the target.

2. Press the CLEAR key.

2-33

2. RADAR OPERATION

;

2.27 Interpreting the Radar Display

2.27.1 False echoes

Occasionally echo signals appear on the screen at positions where there is no target or disappear even if there are targets. False target situations may be recognized, however, if you understand why they are displayed. Typical false echoes are shown below.

Multiple echoes

Multiple echoes occur when a transmitted pulse returns from a solid object like a large ship, bridge, or breakwater. A second, a third or more echoes may be observed on the display at double, triple or other multiples of the actual range of the target as shown below. Multiple reflection echoes can be reduced and often removed by decreasing the gain (sensitivity) or properly adjusting the A/C SEA control.

Sidelobe echoes

Tr u e echo

Target

Own ship

Multiple echo

Multiple echoes

Every time the radar pulse is transmitted, some radiation escapes on each side of the beam. This stray RF is called a “sidelobe.” If a target exists where it can be detected by the sidelobes as well as the main lobe, the side echoes may be represented on both sides of the true echo at the same range. Sidelobes show usually only on short ranges and from strong targets. They can be reduced through careful reduction of the gain or proper adjustment of the A/C SEA control.

Virtual image

A relatively large target close to your ship may show at two positions on the screen. One of them is the true echo directly reflected by the target and the other is a false echo which is caused by the mirror effect of a large object on or close to your ship as shown in the figure below. If your ship comes close to a large metal bridge, for example, such a false echo may temporarily be seen on the screen. Virtual image

Target A

Target B (Spurious)

Sidelobe echoes

Target ship

Mirror image of target ship

Target B (True)

Own ship

Tr u e

echo

False echo

2-34

Virtual image

Shadow sector

2. RADAR OPERATION

Funnels, stacks, masts, or derricks in the path of the antenna block the radar beam. If the angle subtended

Radar antenna

at the antenna is more than a few degrees, a non-detecting sector or blind spot may be produced. Within this sector, targets can not be detected.

Radar mast

2.27.2 SART (Search and Rescue Transponder)

A Search and Rescue Transponder (SART) may be triggered by any X-Band radar within a range of approximately 8 nm. Each radar pulse received causes it to transmit a response which is swept repetitively across the complete radar frequency band.

Screen A: When SART is distant

Radar antenna beamwidth

Echo from SART

(Lines of 12 dots are displayed in concentric arcs.)

Screen B: When SART is close

Echo from SART

(Lines of 12 dots are displayed in concentric arcs.)

Own ship positionOwn ship position

Position of SART

24 NM

Own ship positionOwn ship position

Position of SART

1.5 NM

Appearance of SART signal on the radar display

General procedure for detecting SART response

1. Use the range scale of 6 or 12 nm as the spacing between the SART responses is about 0.6 nm (1125 m) to distinguish the SART.

2. Turn off the automatic clutter suppression (if applicable).

3. Turn off the Interference Rejector.

2-35

2. RADAR OPERATION

2.27.3 Racon (Radar Beacon)

A racon is a radar transponder which emits a characteristic signal when triggered by a ship’s radar (usually only the 3 centimeter band). The signal may be emitted on the same frequency as that of the triggering radar, in which case it is superimposed on the ship's radar display automatically.

The racon signal appears on the PPI as a radial line originating at a point just beyond the position of the radar beacon or as a Morse code signal (see figure below) displayed radially from just beyond the beacon.

Racon

Appearance of racon signal on the radar display

2-36

3. PLOTTER OPERATION

3.1 Plotter Displays

You may show the plotter display over the entire screen, in the overlay screen with the radar display, or in a combination screen.

3.1.1 Full-screen plotter display

Nav data window (Data changes with NAV soft key setting and cursor status. For details see next page.)

Scale

Icon (from left) North Marker Chart Alarm Track Hold Chart Offset Save L/L Offset Battery Simulation (See icon table in the Appendix for details.)

34° 22. 3456'N 359.9°M 080° 22. 3456'E

16.0nm

002WPT

Waypoint name

Waypoint marker

19.9 kt 99.9 nm

S I M

FISH

BRIDGE

Own ship marker

Course bar

Full-screen plotter display

TRIP

Track

MARK ENTRY

MODE

NTH UP

Soft keys

NAV

POS

D. BOX

ON/OFF

Note: When GPS signal error is found, the following occurs depending on the device feeding position data:

FURUNO BB GPS receiver: Alarm icon (

) appears and the aural alarm sounds. Own ship marker blinks faster. Other GPS receiver: The message “NO GPS FIX” appears and is accompanied by the aural alarm and alarm icon. If the GPS signal is missing for more than 90 seconds, the message “NO POSITION DATA” appears.

Nav data window

The data shown in the nav data window depends on the status of the NAV soft key and the cursor.

3-1

3. PLOTTER OPERATION

Latitude and longitude of cursor intersection

Waypoint data (waypoint selected with cursor)

Own ship position

NAV POS

soft key

Own Ship Mark Speed

Latitude, Longitude

34°24. 3456'N 359. 9°

124°24. 3456'W 59.9nm 99. 9nm

Cursor Mark

001WPT

34°24. 3456'N 359. 9°

Bearing to Cursor

Range to Cursor

359. 9°M359. 9°

Trip Distance

TRIP

CourseBearing to WaypointWaypoint Name

19. 9nm 19. 9kt 99. 9nm

SpeedRange to WaypointWaypoint Mark Trip Distance

CourseLatitude, Longitude

TRIP

124°24. 3456'W 19. 9kt 99. 9nm

Trip Distance

Presentation Mode

Destination waypoint data

Own ship speed and course

Turns off nav data window

NAV WPT

soft key

NAV S/C

soft key

NAV OFF

soft key

Time-to-Go to Destination

Bearing to WaypointWaypoint Name

001WPT

Waypoint Mark

Course, Speed

CSE

359. 9°M 359. 9 °M 79. 9°F NU

SOG

19. 9kt 99. 9nm 345 ft

Range to Waypoint

Bearing to Waypoint

BRG RNG

Range to Waypoint

359. 9°M

19. 9nm

TTG

4D02H23M NU

ETA

1st 13:45

Estimated Time of Arrival

TMP DPT

Water Temp.*, Depth*

* Requires appropriate sensor.

Contents of nav data windo w

Presentation Mode

3-2

3. PLOTTER OPERATION

3.1.2 Na v gra phi c di s pl a y

The nav graphic display s hows the compass display or the wind display depending on th e setting of GRAPHIC METER in the NAV GRAPHIC DISPLAY SETUP menu. For further details s ee paragraph 7.10.

Compass display

The compass display, shown in combination displays, provides st eer ing informati on. The compass rose s hows two tri angles: the red tri angle s hows own ship’s cours e and the black triangl e, which moves wi t h s hip’s c our s e, s hows the bearing t o des tination waypoint.

The water temperature and dept h gr aphs, whi c h requi r e appropriate sens or s, show the latest 10 m inutes of water t em per ature and depth data. The range of the depth graph is 50 feet and it is automatically adjusted with depth. You may adjust the update interval f or these graphs on the NAV GRAPHIC DI S P LAY SETUP menu.

Time-to-go to destination

Destination waypoint bearing (black)

Depth graph*

* = Requires appropriate sensor.

Destination waypoint

003WPT

0D 9H 59MTTG 23th23:59

DPT

45.2ft

Shown (in red on color model) when direction to steer is "left."

Speed over ground

Range to destination waypoint

RNG

10.0

SOG

BRG

359.9°

CSE

359.9°M

Speed through water

99.9

ETA

STW

TMP

16.2°F

10.0

Direction to steer (green)

Estimated time of arrival at destination

Ship's course (red)

Water temperature graph*

Bearing scale

Own ship marker (Black when within XTE range, yellow when over.)

XTE monitor (See next page for description.)

Compass display

3-3

3. PLOTTER OPERATION

Reading the XTE (cross-track error) monitor

The XTE monitor, located below the compass rose, shows the distanc e you a re off course and the direction to steer to return to course. The own ship marker moves according to direction and distance off course. It is shown in black when the amount of cross-track error is within the XTE monitor range and yellow when it is over. An arrow app ears at the right or left side of the XTE monitor and it shows the direction to steer to return to intended course. It is shown in red when you should steer left, and green when you should steer right. In the example on the previous page you would steer right to return to course. To maintain course, steer the vessel so the own ship marker stays at the center of the XTE monitor.

Soft keys

You can show the soft keys for the compass display by pressing the HIDE/SHOW key.

COMPSS CNTRL: On the radar/plotter/compass combination display you can switch

control to the compass display by pressing the CNTRL soft key to select COMPSS. EDIT XT-LMT: Sets the range for XTE monitor scale. See the procedure below for how to set. RESET XTE: This soft key may be operated to restart navigation, when a destination is set. Press the EDIT XT-LMT soft key followed by the RESET XTE soft key. The following message is displayed.

RESTART NAVGATION TO CURRENT WPT. ARE YOU SURE? YES ... PUSH ENTER KNOB NO ... PUSH CLEAR KEY

Setting the range for the XTE monitor

1. With the compass (or highway) display shown, press the EDIT XT-LMT soft key to display the following window.

XTE LIMIT

0 .1nm

XTE range setting window

2. Use the Trackball to select digit to change. Note that all digits may be cleared by pressing the CLEAR key.

3. Enter value with the alphanumeric keys.

4. Push the ENTER knob to set, or press the CANCEL soft key to cancel.

3-4

3. PLOTTER OPERATION

4259nm

20.0kt

20.2kt

*D *H *M

* *: *

123

12.3

Anemometer display

The anemometer display shows mostly the same data as the compass display. The wind meter in the center of the display shows wind speed in the bow direction, in graphic and analog forms.

QP<01>

TTG

DPT

WIND SPEED

RNG 4259nm

SOG

WIND APPARENT

45° S

STW

ETA

TMP

°C

12.3kt

Anemometer display

3-5

3. PLOTTER OPERATION

3.1.3 Highway display

The highway display, shown in the combination display of radar/compass/highway and plotter/compass/highway, provides a graphic presentati on of ship’s track al ong intended course. It is useful for monitoring ship’s progress toward a waypoint. The own ship marker shows the relation between ship and intended c our s e. The XTE moni tor shows the direc tion and amount your vessel is of f course – the arrow show s the direction to steer to return to your course and the numeric the distance you are off course. Using t he f igure below as an example, you would steer right 0.009 nm to return t o c our s e. To maintain course, steer the vessel so t he own ship marker stays aligned with t he intended course line.

Destination

Time-to-go to destination

waypoint

WPT001

0D 9H 59MTTG 23th23:59ETA

Range to destination waypoint

RNG 99.9 nm

kt 10.0 ktSTW

10.0

SOG

WPT001

Speed over ground, speed through water

Estimated time of arrival at destination

Destination waypoint

Intended course

Own ship marker

0.9 nm

Shown (in red) when direction to steer is "left."

0.009nm

Direction to steer (green)

XTE monitor

0.9 nm

XTE range

Highway display

Soft keys You can show the soft keys for the highway display by pressing the HIDE/SHOW key.

HIWAY CNTRL: On the radar/plotter/compass combination di s play you can swit c h c ontrol to the highway display by pressing the CNTRL soft key to show HI WAY. EDIT XT-LMT: Sets the range for XTE monitor scale. See the proce dur e on the previous

page for how to set. RESET XTE: This soft k ey m ay be oper at ed to restart navigation, when a destination is s et. Press the EDIT XT-LMT soft key followed by the RESET XTE soft key. See the previous page for details.

3-6

3. PLOTTER OPERATION

3.1.4 Nav data display

The nav data display provides comprehensiv e navigation data, and it is shown in a three-screen combination display. The user may select what data to display and wh ere to display it. For details see the paragraph “7.8 Nav Data Display Setup.”

Appropriate sensors are required. Bars ( - -) appear when corres po nding sensor is not connected.

Position

POSITION

34° 34. 5678' N

120° 34. 5678'

34° 14. 5678' N

120° 14. 5678'

10.0

9.2°

1324.1

Depth

Bearing to Waypoint

Speed through water

Waypoint Position

Water temperature

Nav data displays

SOGWPT POSITION

10.0

COURSESTW

101.6°

RANGEBEARING

0.18

TEMPDEPTH

18.2 °

Range to waypoint

Course

Speed over ground

3-7

3. PLOTTER OPERATION

3.2 Presentation Mode

Three ty pes of presentation mod es are provided for the plotter display: north-up, cours e- up and auto course-up. To change the presentati on m ode, press the HIDE/SHOW key followed by the MO DE s of t key. Each press of the key changes the prese ntation mode and presentat ion mode indication (top right-han d c orner of the scree n) cyclically in t he s equence of North-up, Course-up and Aut o c ourse-up. For C-map mo del, the sequence i s North-up, Perspective, Course-up and Auto course-u p when PERSPECTIVE DISPLAY is set to ON, on the CHART DETAILS menu. (See Chapt er

7.)

North-up

North (zero d egree) is at the t op of the display and own ship is shown with a fil led circle. This mode is useful for long-range navigation.

Course-up

The course- up mode is useful for monitoring ship’s progress towards a waypoint. The destination is at the top of the scr een when a destination is set. When no destination is set, the course or h eading is at the top of the screen at the moment t he c our se-up mode is selected. A fill ed triangle marks ow n s hip’s pos ition.

Note: T he data sentences GGA and V TG must be output f r om t he NavNet display unit connected t o the GPS navigator in order to correctly orient the own ship marker in the course-up mode on other NavNet display units.

Auto course- up

The course is at the top of screen at the moment the auto course-up mode is sel ec t ed. In this mode, the current course is kept at the top of the screen w hen the change is wit hin 22.5 degrees. For example, if your vessel turns larger than

22.5 degrees t o port or starboar d, the chart

display will rotate so that your course is point ing towards t he t op of the screen again. A filled triangl e m ark s own ship’s position.

Perspecti ve ( C-map only)

Chart data is projected in perspective mode, for 3D simulation, during navigation.

34° 22. 3456’N 359.9°M 080° 22. 3456’E

16.0nm

WP-002

FISH

BRIDGE

19.9 kt 99.9 nm

TRIP

NU

MARK ENTRY

MODE

NTH UP

NAV

POS

D.BOX ON/OFF

North-up

34° 22. 3456'N 272.4°M

080° 22. 3456'E

16.0nm

15.9 nm 99.9 nm

WPT 001

TRIP

MARK ENTRY

MODE

CSE UP

CENTER

GO TO CURSOR

D.BOX ON/OFF

Course-up

34° 22. 3456'N 272.4°M

080° 22. 3456'E

15.9 nm 99.9 nm

16.0nm

TRIP

MARK ENTRY

MODE

AT C U

CENTER

GO TO CURSOR

D. BOX ON/ OFF

3-8

Auto course-up

3. PLOTTER OPERATION

3.3 Shifting the Display

The plotter display can be shi f ted as below.

1. Use the Trackball to l ocate the cursor at a screen edge. The screen shifts in the direction opposite of cursor location.

2. To turn off the cursor, press the CE NTER soft key. This also retur ns the own ship marker to the sc r een center.

3.4 Chart Scale

Chart scale (range) may be selected with the [RANGE -] or [RANGE +] key. The [-] key shrinks the c har t range (image is ex panded); the [+] key expands the cart range (image is shrunk). The available ranges are as below.

Charts scales

nm 0.125 0.25 0.5 1 2 4 8 16 32 64 128 256 512 1024 2048*

km 0.23 0.46 0.93 1.85 3.70 7.41 14.8 29.6 59.3 119 237 474 948 1896 3792 sm 0.144 0.29 0.58 1.15 2.30 4.60 9.21 18.4 36.8 73.7 147 295 589 1178 2356

*: 2046 or 2047 i n high latitudes.

3.5 Chart Cards

3.5.1 Chart card overvie w

Your system reads NAVIO NI CS GOLD or C-MAP NT M AX charts, depending o n the type of display unit you have.

When you i ns er t a s uitable chart card in the slot and own ship is near any cartographic object, a chart appears. If a wrong card i s inserted or a w rong c har t scale is selected, landmasses will appear hollow . Chart icons appear at t he t op of the display to help you select a suitable chart scale. T he t able below shows t he c har t icons and their meanings.

Icon Meaning

Proper card is not inserted or chart scale is too small. Press the ZOOM IN soft key to adjust chart scale.

Chart scale is too large. Operate the RANGE key to adjust chart scale.

Suitable chart scale is selected.

Chart icons and their meanings

3-9

3. PLOTTER OPERATION

3.5.2 Indices and chart enlargement

When the RANGE key is operated, you will see several frames appear on the chart. These frames are called indices and they show you what parts of the chart can be enlarged in the current range.

Sample chart (Japan), showing indices

When a chart cannot be displayed:

A chart will not be displayed in the following conditions:

• When the chart scale is too large or too small.

• When scrolling the chart outside th e indices.

• When this happens, select proper chart scale.

Note: Indices can be turned on or off. For further details see “Chart border line” on page 7-14 for NAVIONICS charts and page 7-16 for C-MAP charts.

3-10

3. PLOTTER OPERATION

3.5.3 Navionics

charts

Data for aids to navigation

Selected Navionics charts can show buoy and lighthouse data. Simply place the cursor on the lighthouse or buoy mark.

Lighthouse Buoy

Place the cursor on a lighthouse or buoy mark.

Lighthouse/Buoy marks (U.S. Point layers presentation)

Port service icons

Selected Navionics GOLD charts show services available at ports, with icons.

1. Use the Trackball to place the cursor on the sailboat icon (denotes a port or harbor) desired.

2. Push the ENTER knob.

3. Roll the Trackball horizontally to select icon desired at the t op of the display. The services available appear directly below the icon selected.

4. Press the RETURN soft key to finish.

Detailed information of service selected

List of services at the port selected

34° 22. 3456'N 359.9°M 080° 22. 3456'E

FIRST AID

19.9 kt 99.9 nm

16.0nm

TRIP

GOTO

PORT

Emergency medical service

Water supply station

Fueling station

Traveler's service station

SHOW

PORT

RETURN

Sailboat icon (Port)

Customer service station

Port

Marine equipment service

Information center

Plotter display, showing port service display

3-11

3. PLOTTER OPERATION

Current (or tide) data

Some Navioni c s GOLD charts provide for calculation of the current (or tide) data for any date. Additionally it dis plays the time of sunrise and sunset, m oon shape (on current data.)

1. Use the Trackball to pl ace the cursor on a current icon (

2. Press the ENTER knob to show the cur rent window.

3. Press the DATE soft key, and then enter the date desired.

4. Press the ENTER soft key.

34 24. 3456 N 359.9 NU

124 24. 3456 W 59.9kt 024nm

Time: 04:35

Speed (KT): 0.45ft

Angle ( ): 142

21/08/02 +00

Max. Time Speed Aug. Slack

KT AT Flood 4:58 1.2 323 7:58 Ebb 23:15 1.2 323 20:15 Flood 17:15 1.1 145 15:15 Ebb 23:15 1.2 323 20:15

Moonphase: FULLY IN 1 DAY Sunrise: 05:03 Moonrise: 14:06 Sunset: 19:10 Moonset: 02:15

0.86

0.74

0.61

0.48

0.35 0481216 20 24

Current

DATE

RETURN

Current data display

Object information

You can see detailed informat ion about a place selected by the cursor as below.

1. Use the track ball to place the c urs or on the location you desire to know m or e about.

2. Press the ENTER knob to show the OBJECT INFORMATION window.

34 24. 3456 N 359.9 NU

OBJECT INFORMATION

124 24. 3456 W 59.9kt 024nm

BLOCK AND TACKLE

BOATYARD

LAND AREA

DERDGED AREA

DEPTH AREA

ROCKS

POSITION

47 16.461'N

122 25.153'W

BRG. & RNG.

191 T 0.549nm

VALUE OF SOUNDING

62.2m

VERTICAL DATUM

MEAN SEA LEVEL

MOVE TRACKBALL <-/->)

FIND

RETURN

Object information wi ndow

When there ar e two or more pages, r oll the trackball r ightward to show the nex t page.

3-12

3. PLOTTER OPERATION

FIND function

When the OBJE CT INFORMATION window is shown, objects can be li sted according to their cat egories.

1. Press the F IND soft key wit h the OBJECT INFORMATION window shown.

34 24. 3456 N 359.9 NU

124 24. 3456 W 59.9kt 024nm

FIND ...

PORT LIST PORT SERVICE TIDE STATIONS CURRENT STATIONS OBSTRUCTION ROCKS

ENTER

CANCEL

FIND window

2. Operate the trackball to choose the category to list, and then press the ENTER soft k ey or ENTER k nob.

Note: You c an s how the select ed object on the plott er display by pressing the SHOW soft key.

3-13

3. PLOTTER OPERATION

3.5.4 C-MAP by Jeppesen charts

Cursor and data display

Besides its fundamental functions of providing position data, the cursor can also show information about caution area, depth area, source of data, etc. on C-MAP charts. In addition, you can display information about an icon by placing the cursor on it.

1. Move the Trackball to turn the cursor on.

2. Use the Trackball to place the cursor on the position desired.

3. Push the ENTER knob to open the Objects window.

Objects

Spot Sounding Depth area Exclusive economic zone Military practice area Restricted area Source of data

Objects window

4. Use the Trackball to select the item desired.

5. Push the ENTER knob to display details for object selected.

Depth area

Depth range value1

0.00 Meters

Depth range value2

1829.00 Meters

Example of caution area window

6. Press the CANCEL soft key to close the window.

7. Press the CANCEL soft key to finish.

3-14

3. PLOTTER OPERATION

Icon data

You may plac e the cursor on any icon to find information about the selected icon.

1. For exampl e, place the cursor o n a lighthouse icon.

Place the cursor on a lighthouse icon.

34° 22. 3456'N 359.9°M

080° 22. 3456'E

16.0nm

19.9 kt 99.9 nm

TRIP

MARK

ENTRY

MODE

NTH UP

CENTER

GO TO CURSOR

D. BOX ON /OFF

Lighthous e icon

2. Push the ENTER knob to show data. For example, t he following window appear s for a lighthouse.

Objects

Lighthouse

To we r

Light Underwater Rock Depth contour Depth contour Depth area Source of data

Object windows

3. Use the Trackball to sel ec t the item desired.

4. Push the ENTER knob to display detailed information.

3-15

3. PLOTTER OPERATION

V C

Navigation mark, fixed Light.

Color white Height

7. 00 Meters Light characteristic occulting XXXXXXXX XXXXXXXX

Sample lighthouse data

5. If necessar y, move the Trackball downwar d or upward to scrol l the window.

6. Press the CANCEL soft key twice to finish.

Tide information

The C-MAP NT chart card provides f or c alculation of the t ide heights for any date. Additi onally it displays the times of sunrise and suns et.

1. Use the Trackball to pl ace the cursor on a Ti de icon (

2. Push the ENTER knob to open the Objec ts window.

OBJECTS

Tide height

Cartographic area

Source of data

Objects window

3. Use the Trackball to select Tide height.

4. Push the ENTER knob to open the TIDE window.

34 24. 3456 N 359.9 NU

Objects

Port area Port/Marine Fuel station Water Electricity Showers Pubric toilets Pubric telephone

ertical ursor

124 24. 3456 W 59.9kt 024nm

Time: 04:35L Height: 0.45ft Draught: 0.65ft 28/10/98 43° 32.860N 010° 18.022E

Port information

LIVORNO (LEGHORN)

High Water(max)

Low Water(min)

Sunrise

07:52L

Sunset

16:53 L

0.86

0.74

0.61

UTC

0.48

0.35 0481216 20 24

0.86ft(13:30 L)

0.35ft(21:00 L)

TIDE

DATE

RETURN

Tide window

3-16

3. PLOTTER OPERATION

5. Press the DATE soft key t o open the DATE window .

CHANGE DATE

(DAY. MONTH. YEAR)

2 8. 10. 1998

LIMIT: 31.12.2099

Date window

6. Use the Trackball to posi tion the cursor wher e des ired, then enter date with the alphanumeric keys. Repeat to enter complete d ate.

7. Push the ENTER knob to show the ti dal graph for entered dat e.

8. Use the Trackball to l ocate the vertical curs or on the hour desired.

9. Use the Trackball to shi ft the horizontal cur s or to select draught.

10. See the time, height and dr aught indications in left of t he tide graph for tide information.

11. Press the CANCEL soft k ey twice to close the TIDE window.

Port servic e icons

Selected C-MAP shows s er vi c es avai lable at port s, with lists.

1. Use the Trackball to pl ace the cursor on the sai lboat icon (denotes a port or harbor) desired.

2. Push the ENTER knob.

3. Select the service name desir ed. The services a vai lable appear.

4. Press the CANCEL soft key.

Objects

Port area Port/Marine Fuel station Water Electricity Showers Public toilets Public telephone

Note: When “Por t/Marine” is selected, you can show a picture of t he por t selected, pro vi ded s uch data is available

C-map, port service displa

on the chart card.

FIND function

When the Obj ec t s window is shown, objects can be listed according to t heir categories.

1. Press the F IND soft key with t he Object window.

2. Operate the Track ball to choos e t he c ategory to list, and then press the ENTER soft key or ENT E R k nob. A list appears .

3. Press the CANCEL key twic e to finish.

3-17

3. PLOTTER OPERATION

3.6 Working with Track

Your ship’s track is plotted on the screen using navigation data fed from position-fixing equipment. This section shows you what you can do with track, from turning it on o r off to changing its plotting interval. In the default setting, own ship’s track is turned on and is displayed in red.

3.6.1 Displaying track

Own ship track

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

OWN SHIP TRACK DISP ON OWN SHIP TRACK COLOR RED TARGET TRACK DISPLAY ON TARGET TRACK COLOR WHITE INTERVAL TIME TIME INTERVAL 00m10s DISTANCE INTERVAL 00.10nm MEMORY(TRACK & MARK) 2000 POINTS (MARK MEMORY) (6000)POINTS

SHIP'S TRACK STATUS

TRACKING

TRACK: 1234/2000 MARK : 9/6000

TRACK CONTROL

EDIT

TRACK

RESUME

ERASE T & M

MARK SETUP

RETURN

Track control menu

2. Use the Trackball to select OWN SHIP TRACK DISP.

3. Press the EDIT soft key to show the track display window.

4. Use the Trackball to select ON (default setting) or OFF as appropriate.

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

Note: The number of track and mark points used appears at the SHIP’S TRACK STATUS window on the TRACK CONTROL menu. Using the figure above as an ex ample, 1234 points of track and 9 marks have been recorded.

Target track

Target track, NMEA format TTM (Tracked Target Message) data sentence, may be turned on or off as desired. The default setting is ON.

7. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

8. Use the Trackball to select TARGET TRACK DISPLAY.

9. Press the EDIT soft key to show the target track display window.

3-18

3. PLOTTER OPERATION

10. Use the Trackball to select one of the following: ON or OFF (no ARP or AIS): Turn on or off target tracks ARP ONLY (ARP equipped): Show only ARP tracks. AIS ONLY (AIS equipped): Show only AIS tracks. BOTH: Show both ARP and AIS tracks.

11. Press the ENTER soft key.

12. Press the MENU key to close the menu.

3.6.2 Stopping, restarting plotting of own ship track

When your boat is at anchor or returning to port you probably won’t need to record its track. You can stop recording the track, to conserve the track memory, as follows:

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

▲

SHIP'S TRACK STATUS

TRACKING

TRACK: 1234/2000 MARK : 9/6000

TRACK CONTROL

EDIT

TRACK

RESUME

ERASE T & M

MARK SETUP

RETURN

TRACK

RESUME

TRACK

HALT

▲

SHIP'S TRACK STATUS

NOT TRACKING

TRACK: 1234/2000 MARK : 9/6000

TRACK CONTROL

EDIT

TRACK

HALT

ERASE T & M

MARK SETUP

RETURN

Track is plotted

Track not plotted

Track control menu

2. Press the TRACK RESUME soft key. The soft key now shows “TRACK HALT” and the indication “TRACKING” in the SHIP’S TRACK STATUS window changes to “NOT TRACKING.” In addition, the icon “H” is displayed at the top of the plotter display and own ship marker becomes a hollow circle. To restart plotting the track, press the TRACK HALT soft key

3. Press the MENU key to close the menu.

3.6.3 Changing track color

Track can be displayed in red (default setting), yellow, green, light-blue, purple, blue and white. It can be useful to change track color on a regular basis to discriminate b etween previous day’s track, etc.

Own ship’s track

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

2. Use the Trackball to select OWN SHIP TRACK COLOR.

3. Press the EDIT soft key to display the track color window.

3-19

3. PLOTTER OPERATION

TRACK COLOR

▲



RED



YELLOW



GREEN



LIGHT BLUE



PURPLE



BLUE



WHITE

▼

Own ship track color window

4. Use the Trackball to select the color desired.

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

Target track

Like own ship’s track, target tracks can be displayed in red, yellow, green, light-blue, purple, blue and white (default setting).

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

2. Use the Trackball to select TARGET TRACK COLOR.

3. Press the EDIT soft key to display the track color window.

4. Use the Trackball to select the color desired.

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

3.6.4 Track plotting method and interval for own ship track

In drawing the own ship track, first the ship’s position fed from position-fixing equipme nt is stored into the unit’s memory at an interval of time or distance. A shorter interval provides for better reconstruction of the track, but the storage time of the track is reduced. When the track memory becomes full, the oldest track is erased to make room for the latest.

T rack plotting method

Track may be plotted by time or distance. The default setting is “time.”

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTROL menu.

2. Use the Trackball to select INTERVAL.

3. Press the EDIT soft key to display the plot window.

INTERVAL

▲



TIME



DISTANCE

▼

Interval window

4. Use the Trackball to select TIME or DISTANCE as appropriate. Distance is useful for conserving track memory, since no track is recorded when the boat is station ary.

3-20

3. PLOTTER OPERATION

5. Press the ENTER soft key.

6. Press the MENU key to close the menu.

Track plotting interval

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTRO L menu.

2. Use the Trackball to select TIME INTERVAL or DISTANCE INTERVAL as appropriate.

3. Press the EDIT soft key to display the time or distance interval windo w, depen ding on what you selected at step 2.

TIME INTERVAL

Setting range: 0 min 1 sec (continuous) - 99 min 59 sec Default setting: 10 sec

00m10s

(When selecting TIME INTERVAL.)

DISTANCE INTERVAL

Setting range: 0.00 nm (continuous) - 99.99 nm (km, sm) Default setting: 0.1 nm

00.10nm

(When selecting DISTANCE INTERVAL.)

Interval windows

4. Use the Trackball to select digit and enter value with the alphanumeric keys. The CLEAR soft key functions to clear an entire line of data.

5. Push the ENTER knob or ENTER soft key.

6. Press the MENU key to close the menu.

3.6.5 Changing own ship track/mark distribution setting

The equipment stores a total of 8000 points of track and marks. This amount may be distributed as desired, and the def ault setting is 2000 points of track and 6000 point s for marks.

When you change the track memory setting, all tracks and marks in the memory are erased. If necessary save the data to a memory card. For further details see the paragrap h “6. 1.2 Saving data to a memory card.”

1. Press the MENU key followed by the CHART SETUP and TRACKS & MARKS CONTROL soft keys to open the TRACK CONTRO L menu.

2. Use the Trackball to select MEMORY (TRACK & MARK).

3. Press the EDIT soft key to display the track memory window.

TRACK MEMORY

2000/8000 POINTS

Track memory window

4. Use the Trackball to select digit and use the alphanumeric keys to enter value.

3-21

3. PLOTTER OPERATION

5. Push the ENTER soft key or the ENTER knob. You are asked if you are sure to change the track memory capacity.

6. Push the ENTER knob.

7. Press the MENU key to close the menu.

3.6.6 Erasing track

This paragraph shows you how to erase own ship’s track and target tracks. You can erase ship’s track three ways: collectively, by color and by area.

Erasing own ship track by area

You can erase own ship’s track by area as below. This feature is not available when the overlay mode is in use.

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu.

ERASE ALL TRACKS

ERASE TRACKS BY AREA

ERASE TRACKS BY COLOR

ERASE TARGET TRACKS

ERASE ALL MARKS/LINES

ERASE MARKS BY AREA

SHIP'S TRACK STATUS

TRACKING

TRACK: 1234/2000 MARK : 9/6000

ERASE

EDIT

RETURN

Erase menu

2. Use the Trackball to select ERASE TRACKS BY AREA, then press the EDIT soft key. The menu is erased and the plotter display appears.

3. Use the Trackball to place the cursor at the top left-hand corner of the area which you want to ease track from.

4. Press the START soft key or the ENTER knob.

5. Move the cursor to the bottom right-hand corner of the area which you want to ease track from.

6. Press the END soft key or the ENTER knob. You are asked if you are sure to delete the track.

7. Push the ENTER knob to delete the track selected.

8. Press the MENU key twice to close the menu.

Erasing own ship track by color

You may erase own ship’s track by color as follows:

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu.

2. Use the Trackball to select ERASE TRACKS BY COLOR, then press the EDIT soft key.

3-22

3. PLOTTER OPERATION

ERASE TRK BY COLOR

▲

~ RED { YELLOW { GREEN { LIGHT BLUE { PURPLE { BLUE { WHITE

▼

Erase track by c olor window

3. Use the Trackball to sel ec t the color you want to eras e, then push the ENTER knob.

4. Push the ENTER knob to erase the trac k c olor selected.

5. Press the MENU key twice to close t he menu.

Erasing al l own ship track

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft key s to show the ERASE menu.

2. Use the Trackball to select ERASE ALL TRACKS, then press the EDIT soft key.

3. Push the ENTER knob to erase all own ship track.

4. Press the MENU key twice to close t he menu.

Erasing al l target tracks

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft key s to show the ERASE menu.

2. Use the Trackball to select ERASE TARGET TRACKS, then press the EDIT soft key.

3. Push the ENTER knob to erase all target tracks.

4. Press the MENU key twice to close t he menu.

3.7 Marks, Lines

Marks are useful for denoting important points s uc h as a good fishing spot . Marks can be inscri bed in seven shapes and seven colors: Re d, yellow, green, light-blue, pur ple, blue and white.

{

3.7.1 Entering a mark, line

1. Place the c ur s or where you w ant a mark to appear.

2. Press the SHOW/HIDE key (if necessary) followed by t he MARK ENTRY soft k ey .

The mark is inscribed in t he siz e, color and shape sel ec ted on the mark & line menu. The default mar k attributes are size, large; col or , yellow, and shape, hollow circl e (

Note: T his function can be changed to entering the quick point. For detail, see page 7-10.

○

3-23

3. PLOTTER OPERATION

3.7.2 Changing mark attributes

You can select the shape, size and color for marks on the MARKS & LINES menu.

1. Press the MENU key to show the menu.

2. Press the CHART SETUP, TRACKS & MARKS CONTROL and MARK SETUP soft keys to show the MARKS & LINES menu.

MARKS &

MARKS/LINESCOLOR YELLOW MARKSSHAPE LINESSTYLE MARKSSIZE LARGE





LINES

EDIT

SHIP'STRACKSTATUS

TRACKING

TRACK:1234/2000 MARK:9/6000

RETURN

Marks & lines menu

3. Select MARKS/LINES COLOR, then press the EDIT soft key.

4. Use the Trackball to choose color desired (default setting: yellow).

5. Press the ENTER soft key.

6. Select MARKS SHAPE, then press the EDIT soft key.

MARKS SHAPE

▲



  

   

▼

Marks shape window

7. Use the Trackball to select mark shape desired, then press the ENTER soft key.

8. Select MARKS SIZE, then press the EDIT soft key.

9. Use the Trackball to select LARGE (default setting) or SMALL as appropriate.

10. Press the ENTER soft key.

11. Press the MENU key twice to close the menu.

3.7.3 Selecting line type

You may inscribe lines to denote good fishing spots, areas of special inter est, etc. You can even construct simple charts.

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and MARK SETUP soft keys to show the MARKS & LINES menu.

3-24

3. PLOTTER OPERATION

MARKS &

MARKS/LINES COLOR YELLOW

MARKS SHAPE

LINES STYLE

MARKS SIZE LARGE

LINES

EDIT

SHIP'S TRACK STATUS

TRACKING TRACK: 1234/2000 MARK : 9/6000

RETURN

Marks & lines menu

2. Select LINES STYLE, then press the EDIT soft key.

LINES STYLE

▲





- - - -

 

▼

Lines style window

3. Use the Trackball to select line style desired, then press the ENTER soft key. The line style “dot” disables line drawing. Edge of lines is determined by mark shape. For example, selecting the circle shape will join lines with a circle.

4. Press the MENU key twice to close the menu.

3.7.4 Erasing marks, lines

Erasing an individual mark

1. Operate the Trackball to place the cursor on the mark you want to era se.

2. Press the CLEAR key to erase the mark.

Erasing an individual line

Place the cursor on an end of the line to erase, then press the CLEAR key. Placing the cursor at the intersecting point of two line segments will erase both line segments.

Erasing marks, lines by area

This feature is not available when the overlay mode is in use.

1. Press the MENU key followed by the CHART SETUP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu.

2. Use the Trackball to select ERASE MARKS BY AREA, then press the EDIT soft key. The menu is erased and the plotter display appears.

3. Use the Trackball to place the cursor at the top left-hand corner of the area which you want to erase marks and lines from.

4. Press the START soft key or the ENTER knob.

3-25

3. PLOTTER OPERATION

5. Move the cursor to the bottom right-hand corner of the area which you want to erase marks and lines from.

6. Press the END soft key or the ENTER knob. You are asked if you are sure to delete the marks/lines selected. Press the ENTER knob to delete.

7. Press the MENU key twice t o close the menu.

Erasing all marks, lin es

You can erase all marks and lines collectively. Be absolutely sure you want t o erase all marks and lines - erased marks and lines cannot be restored.

1. Press the MENU key follo wed by the CHART SET UP, TRACKS & MARKS CONTROL and ERASE T & M soft keys to show the ERASE menu.

2. Use the Trackball to select ERASE ALL MARKS/LINES, then press the EDIT soft key.

3. Push the ENTER knob to erase all marks and lines.

4. Press the MENU key twice t o close the menu.

3.8 Waypoints

In navigation terminology, a waypoint is a particular location on a voyage whether it be a starting, intermediate or destinat ion point. A waypoint is the simplest piece of information your equipment requires to get you to a destination, in the shortest distance possible.

This unit has 999 waypoints into which you can ent er posit ion information. You may enter a waypoint five ways: at own ship position, at MOB posit ion (see page 1-13 for details), by cursor, by range and bearing, and through the waypoi nt list (manual input of latitude and longitude).

3.8.1 Entering waypoints

Entering a waypoint at own ship position

Press the SAVE/MOB key momentarily to store your position as a waypoint. This new waypoint is saved to the waypoint list, under the youngest empty waypoint number.

Entering a waypoint with the cursor

1. Press the MENU key to open the menu.

2. Press the WAYPOINTS/ROUTES, WAYPOINTS and WA YPOI NT BY CURSOR soft keys. The plotter display appears.

3. Operate the Trackball to place the cursor where you want to enter a waypoint.

4. Press the NEW WPT soft key. The waypoint windo w appears and it shows waypoint mark shape, waypoint name, comment (default: time and date), position of waypoi nt and proximity alarm radius.

3-26

3. PLOTTER OPERATION

NEW

MARK

▲

PROXIMITY ALARM RADIUS

NAME

0 01WPT

34°44.000'N 135°21.000'W

COMMENT

02:36 01JAN01

LAT

34° 12. 134'N

LON

134° 12. 345'W

002WPT

00:00 01JAN00

34°44.000'N 135°21.000'W

003WPT

00:00 01JAN00

34°44.000'N 135°21.000'W

359.9°

0.00nm

359.9°

0.00nm

359.9°

0.00nm

0. 00nm

WPT

SELECT MARK

COORD TYPE

N< - - >S E< - - >W

SAVE

RETURN

Waypoint window

5. If you do not need to change the waypoint data, press the SAVE soft key to register the waypoint. The steps which follow show you how to change waypoint data.

6. Press the SELECT MARK soft key.

7. Press the MARK SHAPE soft key to open the mark shape selection window.

SELECT MARK

Waypoint mark shape selection window

8. Operate the Trackball to select shape desired.

9. Press the ENTER soft key.

10. Press the SELECT MARK and MARK COLOR soft keys in that order to open the waypoint mark color selection window. Select the color desired, then press th e ENTER soft key.

SELECT COLOR

▲

 RED  YELLOW  GREEN  LIGHT BLUE  PURPLE  BLUE  WHITE

▼

Waypoint mark color selection window

3-27

3. PLOTTER OPERATION

Note: You cannot change the shape and color of a waypoint when the proximity alarm radius for it is other than “zero.” To change shape or color, enter all zeroes as the proximity alarm radius.

11. You can change the name (6 characters), comment (13 characters), L/L position and the proximity alarm radius for a waypoint as follows:

Use the Trackball to select the NAME, COMMENT, position box or PROXIMITY ALARM

RADIUS field. (“Proximity alarm radius” provides for audio and visual alarms when your boat nears a waypoint by the distance specified. The proximity alarm must be turned on

in the ALARM menu to use this feature. For details see the paragraph 3.11.6.) Use the Trackball to select location. Enter appropriate alphanumeric character with the alphanumeric keys.

12. Press the SAVE soft key to register the waypoint.

13. Enter another waypoint, or press the MENU key t o close t he menu.

Entering a waypoint by range and bearing

This method is useful when you want to enter a waypoint using range and bearing to a target found on a radar.

1. Press the MENU key to open the menu.

2. Press the WAYPOINTS/ROUTES, WAYPOINTS and WAYPOINT BY RNG & BRG soft keys.

3. A red “X” appears at own ship position, and it is the origin point for range and bearing. Operate the Trackball to place t he cursor on the location desired. Range and be aring from own ship to the cursor appear at the top of the display.

Note: The origin point of range and bearing can be shifted to the location desired. Operate the Trackball to select location, then press the START POINT soft key.

4. Press the NEW WPT soft key. The waypoint window appears and it shows mark shape, waypoint name, comment (default: date and t im e), position of waypoint and proximity alarm radius.

NEW

MARK

▲

PROXIMITY ALARM RADIUS

NAME

0 01WPT

34°44.000'N 135°21.000'W

COMMENT

02:36 01JAN01

LAT

34° 12. 134'N

LON

134° 12. 345'W

002WPT

00:00 01JAN00

34°44.000'N 135°21.000'W

003WPT

00:00 01JAN00

34°44.000'N 135°21.000'W

359.9°

0.00nm

359.9°

0.00nm

359.9°

0.00nm

0. 00nm

WPT

SELECT MARK

COORD TYPE

N< - - >S E< - - >W

SAVE

RETURN

Waypoint window

5. If necessary, change waypoint data following the instructions from step 6 t hrough 11 in “Entering a waypoint with the cursor” on page 3-26.

6. Press the SAVE soft key to register the waypoint.

7. Enter another waypoint as above, or press the MENU key to finish.

3-28

3. PLOTTER OPERATION

Entering a waypoint from the waypoint list

You can manually enter waypoint posit ion from the waypoint list as follows:

1. Press the MENU key to open the menu.

2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys.

3. Press the LOCAL LIST (lists waypoints in order from nearest to furthest, maximum 32 points) or ALPHANUMERIC LIST (lists waypoints in ALPHANUMERIC order) soft key.

ABALONE

▲

00:00 01JAN01

CRAB

00:00 01JAN01

PUSH ENTER KNOB TO SEARCH FOR

FISH

LOBSTER

Alphanumeric waypoint list

BRG 350.9 RNG 3.80nm

35°47.010'N 135°21.000'W

BRG

050.9°

RNG

1.98nm

34°42.000'N 135°21.050'W

BRG

065.9°

RNG

1.83nm

34°41.000'N 135°21.030'W

BRG

144.9°

RNG

4.93nm

38°44.300'N 135°21.010'W

---

234/250

WPT ALPHA

GOTO

NEW WPT

EDIT WPT

ERASE WPT

RETURN

FISH

▲

00:00 01JAN01

CRAB

00:00 01JAN01

ABALONE

00:00 01JAN01

LOBSTER

00:00 01JAN01

BRG

065.9°

RNG

1.83nm

34°41.000'N 135°21.030'W

BRG

050.9°

RNG

1.98nm

34°42.000'N 135°21.050'W

BRG 350.9 RNG 3.80nm

35°47.010'N 135°21.000'W

BRG

144.9°

RNG

4.93nm

38°44.300'N 135°21.010'W

Local waypoint list

234/250

WPT LOCAL

GOTO

NEW WPT

EDIT WPT

ERASE WPT

RETURN

Alphanumeric and local waypoint lists

4. Press the NEW WPT soft key to show the waypoint window (see the figure on the previous page). Own ship position is shown in the position box.

5. Select the position box and enter positi on desired.

6. If desired, change waypoint data following the instructions from step 6 in “Editing a waypoint from the plotter display” on pag e 3-30.

7. Press the SAVE soft key to register the waypoint.

8. Press the MENU key to close the menu.

3.8.2 Editing waypoint data

Waypoint data may be edited from the waypoint list or directly from the plotter display.

Editing waypoint data from the waypoint list

1. Press the MENU key to open the menu.

2. Press the WAYPOINTS/ROUTES and WAYPOINTS soft keys.

3. Press the LOCAL LIST or ALPHANUMERIC LIST soft key as appropriate.

4. Use the Trackball to select the waypoint you want to edit.

5. Press the EDIT WPT soft key.

6. Edit data as appropriate.

7. Press the SAVE soft key.

8. Press the MENU key to close the menu.

3-29

3. PLOTTER OPERATION

Editing a waypoint from the plotter display

You may edit waypoints from t he plotter displ ay as follows:

1. Press the MENU key followed by the WAYP OINTS/ROUTES and WAYP OINTS soft key to open the waypoint menu.

2. Press the WAYPOINT BY CURSOR soft key.

3. Operate the Trackball t o place the cursor on th e waypoint which you want to change. A flashi ng diamond mark appears on the waypoi nt when it is correctly selected.

4. Press the EDIT/MOVE soft key. Three soft key s replace the EDIT/MOVE soft key:

EDIT WPT: Edit from t he waypoint ent ry window. MOVE WPT: Move waypoint to new position with the cursor. ERASE WPT: Erase waypoint. See paragr aph 3.8.3.

5. Press the appropriate soft k ey. For the “EDIT WPT,” the waypoint entry window appears; edit data as appropri ate. For “MOV E WPT,” do the following:

a) Operate the Trackball to place the cursor on the location desired for the waypoint. A

line connects previous pos ition and new position.

b) Push the ENTER knob. The waypoint moves to the cursor position and its position is

changed on the waypoint list. If the waypoint is set as destination or is part of a route, you are asked if you are sure to move the waypoint. In this case, push the ENTER knob to move the waypoint, or press the CLEAR key to cancel.

6. Press the MENU key to finish.

Range and bearing from own ship to cursor

(1) Select waypoint to move, then press EDIT/MOVE and MOVE WPT soft keys.

(2) Drag cursor to new position, then push the ENTER knob.

34° 22. 345’N 86.6°M

080° 22. 345’E

16.0nm

FISH

WP-002

4.53nm 99.9 nm

BRIDGE

TRIP

RNG BRG

CANCEL

Press to alternately display range/bearing from own ship to cursor, range/bearing from original waypoint position to cursor position. Below is an example of the range/bearing from original waypoint position to cursor position.

34° 22. 3456’N FROM 5.3°M

080° 22. 3456’E

FISH 1.45 nm

Plotter display

3.8.3 Erasing waypoints

Erasing a waypoint directly from the plotter display

1. Operate the Trackball t o place the cursor on th e waypoint you want to erase. A flashing diamond mar k appears over the waypoint when the waypoint is correc t ly selected.

2. Press the CLEAR key. You are as k ed if you are sure to er as e t he waypoint.

3. Push the ENTER knob. The waypoint is erased from the plotter screen and the waypoi nt list.

3-30

3. PLOTTER OPERATION

Erasing a waypoint from the menu

1. Press the MENU key followed by the WAYP OINTS/ROUTES and WAYP OINTS soft key to open the waypoint menu.

2. Press the WAYPOINT BY CURSOR soft key.

3. Operate the Trackball t o place the cursor on th e waypoint which you want to erase. A flashi ng diamond mark appears on the waypoi nt when it is correctly selected.

4. Press the EDIT/MOVE soft key followed by the ERASE WPT soft key. You are asked if you are sure t o eras e the waypoint.

5. Push the ENTER knob to erase the waypoint.

6. Press the MENU key t o c lose the menu. T he waypoint is erased from the plotter screen and the waypoint list.

Erasing a waypoint from the waypoint list

1. Press the MENU key t o open the menu.

2. Press the WAYPOINTS /ROUTES and WAYPOI NTS soft keys.

3. Press the LO CA L LIST or ALPHANUMERIC LI ST soft key.

4. Use the Trackball to sel ec t the waypoint you want to erase.

5. Press the ERASE WPT soft key. You are asked if you are sure to erase the waypoint.

6. Push the ENTER knob. The waypoint is erased from both the waypoi nt list and the plotter s cr een ( if it is currently displayed).

7. Press the MENU key t o c lose the menu.

3.8.4 Changing waypoint mark size (Navionics GOL D)

You may c hange the size of all w ay point marks to small or lar ge ( def ault), or you may turn them off.

1. Press the MENU key t o open the menu.

2. Press the CHART SETUP and CHA RT CONFIGURATION soft key s.

LAT/LON GRID GREEN

TEXT INFORMATION ON

WAYPOINTS LARGE

WAYPOINT NAMES ON

CHART BORDER LINES ON

LANDMASS BRT YELLOW

BACKGROUND BLACK

NAVAIDS ON

LIGHT SECTOR INFO ON

OTHER SYMBOLS WHITE

MARK SIZE LARGE

CHART CONFIG

EDIT

CNTOUR LINE

RETURN

Chart details menu

3. Use the Trackball to select WAYPOINTS.

4. Press the EDIT soft key.

3-31

3. PLOTTER OPERATION

5. Use the Trackball to select LARGE, SMALL or OFF.

LARGE: Shows mark in actual shape. SMALL: Displays all waypoints with an “X” regardless of mark shape selected. OFF: Turns off all waypoints and their names. Waypoints currently us ed in navigation

are shown regardless of this setting.

6. Press the ENTER soft key.

7. Press the MENU key to close the menu.

3.8.5 Searching waypoints

You can search for a waypoint through the alphanumeric waypoint list as follows:

1. Press the MENU key.

2. Press the WAYPOINTS/ROUTES, WAYPOINTS and ALPHANUMERIC LIST soft keys to show the alphanumeric list.

ABALONE

▲

00:00 01JAN01

CRAB

00:00 01JAN01

PUSH ENTER KNOB TO SEARCH FOR

FISH

LOBSTER

BRG 350.9 RNG 3.80nm

35°47.010'N 135°21.000'W

BRG RNG

34°42.000'N 135°21.050'W

BRG RNG

34°41.000'N 135°21.030'W

BRG RNG

38°44.300'N 135°21.010'W

050.9°

1.98nm

065.9°

1.83nm

144.9°

4.93nm

---

Search window

234/250

WPT ALPHA

GOTO

NEW WPT

EDIT WPT

ERASE WPT

RETURN

Alphanumeric list

3. Use the Trackball and the alphanumeric keys to enter up to three alphanumer ic characters in the search window. Then, the waypoint searched ap pears at the top of the screen.

4. Press the MENU key to close the menu.

3-32

3. PLOTTER OPERATION

3.9 Routes

Often a trip from one place to another in vol ves several course changes, requiring a series of route points (waypoints) which you navigate t o, one after another. The sequence of waypoints leading to the ultim at e destination is called a route. Your unit can automatically advance to the next waypoint on a route, so yo u do not have to change the destination waypoint repeatedly.

You can store up to 200 routes, and a route may have 35 waypoints.

3.9.1 Creating routes

Entering a route with exis ting waypoints

This method constructs routes by using existing waypoints. F or C-MAP, t he SAF E ROUT E CHECK function should be done for creating rout es.

1. Press the MENU key.

2. Press the WAYPOINTS/ROUTES soft key.

3. Press the ROUTES soft key to open the ROUTE menu. (No data will be shown if there are no routes entered.)

Total length of route

Route name

Number of waypoints in route

001

▲

002

003

004

PUSH ENTER KNOB TO SEARCH FOR

LENGTH

25.6 nm

WAYPOINTS 35

LENGTH

56.7 nm

WAYPOINTS 2

LENGTH

21.1 nm

WAYPOINTS 3

LENGTH

21.1 nm

WAYPOINTS 3

---

1/20

ROUTE

GOTO

NEW ROUTE

EDIT ROUTE

ERASE ROUTE

RETURN

Route menu

4. Press the NEW ROUTE soft key to open the new route entry screen.

3-33

3. PLOTTER OPERATION

NEW

ROUTE NAME

0 0 1

COMMENT

ROUTE

PLOT

LOCAL LIST

ALPHA LIST

CONECT

CANCEL

New route entry screen

5. If desired you can change the route name shown and/or add a comment. A route name may consist of six characters; comment, 13 characters.

6. Press the LOCAL LIST or ALPHA LIST soft key to open the waypoint list.

7. Use the Trackball to select a waypoint, then press the ADD WPT soft key to add it to the route.

8. Repeat step 7 to complete the route. Note: To clear last-entered waypoint, press the ERASE LST WP soft key. Each press of this key deletes the last waypoint entered.

9. Press the SAVE soft key to register the route.

10. Press the MENU key to close the menu.

Entering a route with the cursor

This method allows you to construct a route directly from the plotter display, using existing waypoints or new positions. Any new position will be save d as a waypoint, under the youngest empty waypoint number.

1. Follow steps 1-5 in “Entering a route from the route list” on the previous page.

2. Press the PLOT soft key to show the plotter display.

3. Operate the Trackball to place the cursor on an existing waypoint (A DD WP soft key appears) or new location (ADD NEW WP soft key appears).

4. Press the ADD WP soft key (or ADD NEW WP soft key).

5. Repeat steps 3 and 4 to complete the route.

6. Push the ENTER knob to register the route.

Creating voyage-based routes

You can create routes based on your ship’s track. The route can be created auto matically by time or distance, or manually. This feature is useful when you wish to retrace prev ious track.

The “SAVE” icon (SAVE) appears at the top of the screen when a voyage-based route is being created.

3-34

1. Press the MENU key to open the menu.

2. Press the WAYPOINTS/ROUTES soft key.

3. Press the CREATE VOYAGE-BASED ROUTE soft key.

3. PLOTTER OPERATION

001

▲

002

003

004

PUSH ENTER KNOB TO SEARCH FOR

LENGTH

25.6 nm

WAYPOINTS 35

LENGTH

56.7 nm

WAYPOINTS 2

LENGTH

21.1 nm

WAYPOINTS 3

LENGTH

21.1 nm

WAYPOINTS 3

---

1/20

SAVE ROUTE

NEW

SELECT ROUTE

RETURN

Save route menu

4. Press the NEW soft key to show the new route window. Note: If you want to tack voyage-based points onto the end of an existing route, select

the route with the Trackball, then press the SELECT ROUTE soft key instead of the NEW soft key. Then, go to step 6.

SAVE ROUTE

BCKTRK TIME

Next consecutive route number

ROUTE NAME

0 0 6

BCKTRK

COMMENT

USE FURUNO BACK TRACK FUNCTION TO AUTOMATICALLY CREATE ROUTE BY TIME OR DISTANCE.

DIST

MANUAL

CANCEL

Save route window

5. If required, you may change the route name and enter a comment.

6. Choose how to record points for your route, by time, by range or manual entry, by

pressing BCKTRK TIME, BCKTRK RANGE or MANUAL soft key as appropriat e. For manual entry, go to step 8. For BCKTRK TIME, BCKTRK DIST one of the following displays appears.

TIMEINTERVAL DISTANCEINTERVAL

00h01m

00.1nm

(When selecting BCKTRK TIME.)

(When selecting BCKTRK DIST.)

Displays for entry of time, distance interval

3-35

Furuno 1954c, 1834c, 1934c, 1964c User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

IMPORTANT NOTICES

TABLE OF CONTENTS

FOREWORD

A Word to the Owner of the Model 18x4C/19x4C Series Marine Radar, GD-1920C Color Video Plotter

Features

SYSTEM CONFIGURATIONS

1. OPERATIONAL OVERVIEW

1.1 Operating Controls

1.2 Inserting a Chart Card

1.3 Turning the Unit On/Off

1.4 Display Brilliance, Panel Brilliance, Hue

1.5 Selecting a Display

1.6 Trackball, Cursor

1.8 Data Boxes

1.9 Function Keys

1.10 Simulation Display

2. RADAR OPERATION

2.1 Radar Display

2.2 Transmitting, Stand-by

2.3 Tuning

2.4 Adjusting the Gain

2.5 Reducing Sea Clutter

2.6 Reducing Precipitation Clutter

2.7 Range Scale

2.8 Pulselength

2.9 Presentation Mode

2.10 Measuring the Range

2.11 Measuring the Bearing

2.12 Erasing the Heading Line, North Marker

2.13 Reducing Noise Interference

2.14 Rejecting Radar Interference

2.15 Zoom

2.16 Shifting the Picture

2.17 Using the Offset EBL

2.18 Echo Trails

2.19 Echo Stretch

2.20 Echo Averaging

2.21 Outputting TLL Data

2.22 Guard Alarm

2.23 Watchman

2.24 Suppressing Second-trace Echoes

2.25 Waypoint Marker

2.26 ARP, TTM Operation

2.27 Interpreting the Radar Display

3. PLOTTER OPERATION

3.1 Plotter Displays

3.2 Presentation Mode

3.3 Shifting the Display

3.4 Chart Scale

3.5 Chart Cards

3.6 Working with Track

3.7 Marks, Lines

3.8 Waypoints

3.9 Routes