Furman CN-15MP Data Sheet

CN-15MP & CN-20MP

Contractor Series MiniPorts

Features

• Provides AC control for equipment located away
from system racks with primary power conditioners/
sequencers (i.e. powered speakers).

• Sequencing of duplex initiated remotely by standard
analog triggering (remote terminal) or digital link
(SmartSequencing from CN-1800S or CN-2400S).

• SmartSequencing Technology allows multiple units
to be daisy chained at runs of over 1,000’ between
units with bi-directional communications between
units for sequencing on and off large and/or complex
systems.

• IP Control (Telnet or cloud-based BlueBOLT) via
SmartSequencing (when connected to CN-1800S/
CN-2400S with BB-RS232 Adaptor.

CN-15MP

(shown without
Phoenix-type
connectors and
security cover)

• Remote terminal supports connections to legacy
Furman (non-Contractor Series) and third party power
sequencers for maximum installation flexibility.

• DIP switches and potentiometer allows customiza­tion of settings such as sequencing delays, 12V on/
off, and more.

• Extreme Voltage Shutdown (EVS) safeguards from
catastrophic under-voltage (under 80V sustained) or
over-voltage (over 145V sustained) conditions. Circuit
may be set to auto-reset when voltage returns to
normal or manual reset after an event is detected.

• Security covers prevent unauthorized personnel
from tampering with DIP switches.

Force Off Phoenix-type
2-pin connector with
screw terminals

SmartSequencer Port
Phoenix-type 4-pin
connector with
screw terminals

Primary/Secondary
Link Indicators

CN-20MP

(shown with
Phoenix-type
connectors and
security cover)

• Fire alarm shut off.

• Available with 15 amp capacity (CN-15MP) or
20 amp capacity (CN-20MP).

• Safety agency listed (CSA).

• 15 Year Limited Product Warranty.

See warranty policy documentation for terms and conditions.

15 YEAR

15 YEAR

PRODUCT WARRANTY

PRODUCT WARRANTY

See actual warranty documentation for details.

Remote Port Phoenix-type 5-pin
connector with screw terminals

AC Receptacles:
CN-15MP (Shown)
NEMA-15R

CN-20MP
NEMA-20R 20A

®

Potentiometer for Fine
Tune Delay Time

DIP switches for
configuring settings

Bypass switch
overrides relay for
troubleshooting or
in event of control
system failure

www.furmancontractor.com 800-472-5555

Extreme Voltage/
Power Indicators

Circuit Breaker:
15A CN-15MP
CN-20MP No Circuit Breaker

10 ft. AC power cord AC cord with strain relief CN-15MP: NEMA-15P

CN-20MP: NEMA-20P

BYPASS

1M

2M

4M

N.O.

N.C.

12V ON

12V OFF

1

2

3 4

5

GND

ON

MOM

MNT

PRI

SEC

EVS ON

EVS OFF

6

7

8

9

DLY

ADJ

C US

Specifications

AC Voltage Input Range
90-139VAC, 50/60Hz
Maximum AC Current Rating
CN-15MP: 15 Amps (Thermal breaker)
CN-20MP: 20 Amps

AC Cord:

CN-15MP: 3/14AWG, 10 feet, black, fixed, NEMA 5-15P plug
CN-20MP: 3/12 AWG, 10 feet, black, fixed, NEMA 5-20P plug

AC Receptacles:

CN-15MP: 2 NEMA 5-15R’s (1 duplex)
CN-20MP: 2 NEMA 5-20R’s (1 duplex)

Under-Overvoltage Protection:

AC Undervoltage Protection: EVS, 77VAC+/-3VAC
AC Overvoltage Protection: EVS, 140VAC+/-5VAC
EVS Enable/Disable (configurable)

Operating Temperature Range:
5C (40F) to 40C (105F) degrees
Humidity Range:
<90% rH (Relative Humidity)
User Interface:

Circuit Breaker: Pushbutton, 15A (CN-15MP),
20A (CN-20MP) No Breaker
Front panel diagnostic indicators (LED): Power, Extreme Voltage, Primary
Link, Secondary Link

Specifications subject to change due to product upgrades and improvements.

Dimensions and Weight

User Interface (continued):
Side Panel DIP Switches: Side panel. hidden by security cover, 1 Minute Delay,
2 Minute Delay, 4 Minute Delay, Force Off NO/NC, 12V Mode On/Off GND Mode
On, Momentary/Maintained, Primary/Secondary, EVS Reset Auto/Manual
Potentiometer: Side panel, hidden by security cover, fine tune delay adjust

Control/Status/Triggering (Top Panel):

Remote Terminal: +5-30VDC In, 12VDC (12mA) Out
SmartSequencing: Phoenix-type 4-Pin Connector, Screw Terminals,
Primary & Secondary Links (Current Loop - 1000’ nominal)
Remote Terminal: Phoenix-type 5-Pin Connector With Screw Terminals;
+12V, STAT, REM, GND, DLY OUT(Class 2 Wiring)
Force Off: Phoenix-type 2-Pin Connector With Screw Terminals,
FORCE OFF: (Class 2 Wiring)
IP Addressability: Optional, via CN-1800S or CN-2400S with BB-RS232
Ethernet/RS-232
Adaptor (sold separately) for IP control via Telnet, HTTP, BlueBOLT®
Voltmeter: Available via SmartSequencing communication, +/- 2VAC accuracy
Ammeter: Available via SmartSequencing communication, +/-1A accuracy

Power Consumption (No Load): 10 Watts
Safety Agency: CSA
RoHS Compliant: Yes

C US

7.375 in.

Common FRONT dimensions for both CN-15MP and CN-20MP

6.25 in.

4.75 in.

FORCE

OFF

REMOTE

PORT

POWER

120 VAC, 50/60 Hz
MAX LOAD 15A

+12V

STAT

REM

GND

DLY OUT

C US

SMARTSEQUENCING

OUT

PRIMARY

LINK

SECONDARY

LINK

IN

EXTREME VOLTAGE

MINIPORT

P

P

S

S

15 AMP

CLASS 2 WIRING

CN-15MP

6.5 in.

SIDE CN-15MP SIDE CN-20MP

Allow 1 extra inch for connectors Allow 1 extra inch for connectors

2 in.

BYPASS

C US

2.5 in.

BYPASS

C US

5.5 in.

Unit Weight: 3.75 lbs. (both models)

www.furmancontractor.com 800-472-5555

Power Cord-10 feet, black, fixed, NEMA

• (CN-15MP) 3/14AWG, 5-15P plug

Power Cord-10 feet, black, fixed, NEMA

• (CN-20MP) 3/12AWG, 5-20P plug

CN-15-20-MP 9-12