Furman ASD-120 2.0 Datasheet

20 A

12

ON

OFF

REMOTE

ASD-120 2.0

6 CHANNEL SEQUENCING POWER DISTRIBUTOR

The ASD-120 2.0 is a six channel power sequencing device intended for use in installations where multiple electrical loads must be powered on and off in a delayed

and orderly sequence. Typical applications for the ASD-120 2.0 include: touring PA or sound reinforcement systems, musical or theatrical acts, mobile recording facilities,

and on-location film or video shoots. Essentially, any situation where AC power must be distributed to multiple circuits and activated or deactivated in discrete stages

would benefit from the use of an ASD-120 2.0.

Applications for:

PRO AUDIO

RECORDING

DJ EQUIPMENT

INSTRUMENT RIGS

PRODUCT FEATURES

• 120 amp 120 volt AC sequenced distro and controller

• Six Independent 20 amp circuits @ 120V - 120 amp total load
capacity

• Six delay banks with rear panel NEMA 5-20R duplex outlets and
optically isolated DC relay outlets

• Front panel status power LED, Bypass Switch and Circuit
Breaker for each Delay Bank

• 120A power distribution block accommodates 120V/240V
single phase, or 120/208-Y three phase power

• X Y Z Status LED confidence indicators for each Input Phase

• Sequence unit ON or OFF from front panel or by remote switch

Relays

12 Total AC Outlets Six 20A Distribution

Circuits

• Independent three position switches to power sequence (SEQ)
or Bypassed ON or OFF each Bank

• Adjustable Delay with up to 7 Minute Interval between Banks,
Total maximum Sequence Time 35 minutes

• Remote interface with an isolated 12VDC, 250mA power source
for external secondary applications

• Signal level relay contacts (NO or NC) used to control and
sequence other units

• Front panel key switch and anti-tamper DIP cover for added
security

• Force Off emergency shutdown

• Rugged two rack space (2RU) chassis

REMOTE

ON

OFF

Indicator Lights

Power Sequencing

Security Keyswitch6 Bank External

Please Note: Because the ASD-120 2.0 switches hazardous voltages and high currents, we recommend that the installation be performed by a qualified electrician. For safe operation,

the ASD-120 2.0 must be installed in accordance with local/municipal requirements and the National Electrical Code (NEC). Please feel free to contact Furman Technical Services if you
have any questions or concerns regarding the installation, operation or application of the ASD-120 2.0.

www.furmansound.com 800-472-5555

FRONT and BACK PANEL FEATURES

Indicator LEDs for
Delay A, B and C

Multi-function DIP Switch
7 Position ON/OFF

Security Cover to Protect Program Settings

Sequence Bypass Switch
6 Position ON/SEQUENCE/

Indicator LEDs for
Delay D, E and F

Front Panel Key Switch
for Remote Security

Front Panel Start
Sequence Switch

Integrated Front
Panel Rack Ears

Adjustable Rack
Ears to Securely
Connect to the
Back of Rack.
Maximum reach

20.75 in.

Circuit Breakers 20A
for Delay A, B and C

AC Power Inlet 1.5 Inch
Cable/Cord Clamp

Delay
Adjustment

Indicator LEDs for
Phases X, Y and Z

Six 20A
Duplex Outlets

SPECIFICATIONS

AC Input Voltage

120/240V single phase, or 120/208V three phase.

Input Current: 120 Amps maximum

Output: Six, 120V 20A circuits

Maximum AC Current Rating

Six, 120V 20A circuits for 120A total.

Power Distribution Block

Wire Gauge 2, 3, 4-6 AWG,

Phase indicators: 3 LEDs, one per phase X, Y, and Z

AC Output Receptacles

Rear Panel Outlets: 6 duplex NEMA 5-20R sequenced.

Front Panel: 6 thermal circuit breakers, one per

duplex pair.

Operating Temperature and Humidity

5 to 40C (40 to 105F), <90% Relative Humidity

Specifications are subject to change without notice due to design improvements and upgrades.

User Interface

Key-switch: Front panel, 3 position (On/Off/Remote)

Keys: Included, 1 pair

Push Button Switch: Front panel

Circuit Breakers: Front panel, push-button; 6, 20A Thermal Breakers

Output Circuit Status: Front panel indicators – one per output

Configuration Switches: Front panel, hidden by security cover;

3 maximum delay switches – 1, 2, and 4 minute

Force Off NO/NC, 12V mode On/Off, GND mode ON,

Momentary/Maintained mode selection

Fine Delay Adjustment: Potentiometer hidden by security cover.

Sequence Bypass : 6 Switches, 3 States (ON/SEQUENCE/OFF)

Phase indicators: 3 LEDs, one per phase X, Y, and Z

Circuit Breakers 20A for

Delay D, E and FOFF

Force Off, 2 Pin
Phoenix-type Connector

Delay Outputs, 8 Pin
Phoenix-type Connector

Remote, 4 Pin
Phoenix-type Connector

Control/Status/Triggering (Rear Panel)

Remote Terminal: Phoenix-type 4 Pin Connector w/Screw
Terminals;

+12V @ 250mA, STAT, REM, GND (Class 2 wiring)

+5 to 30VDC at REM input terminal.

Delay Outputs: Phoenix-type 8-Pin Connector with Screw
Terminals

6 relay contacts with NO and NC common connections

(Class 2 wiring)

A, B, C, D, E, and F relay contacts switched with output circuits,
1A@48VDC

Force Off: Phoenix-type 2 Pin Connector with Screw Terminals;

Optically isolated, 12V, 10mA current source

(Class 2 wiring)

Senses external relay contact closure

Power Consumption

Standby: 5 Watts

Sequenced ON: 20 Watts

Safety Agency

NTRL-C, RoHS Compliant

Removable
Front Panel
Handles

Weights, Dimensions anD UPC CoDes

Model PRodUCT diMensions WeighT CARTon diMensions WeighT single UniT UPC MAsTeR PACk QTy MAsTeR PACk UPC

ASD-120 2.0 19” L x 10” D x 3.5” H 16 lbs. 22”L x 18.5”D x 8”H 18 lbs. 654061041191 2 50654061041196

www.furmansound.com

Furman 1800 S. McDowell Blvd., Petaluma, CA 94954

Furman is registered trademark of Core Brands LLC, a Nortek Company.

©2016 Core Brands, LLC. All rights reserved.

ASD-120 12-30-15