TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
:
The lightning fl ash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of suffi cient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
The caution marking is located on the rear of the cabinet.
Laser Safety
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible
eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO
LOCATION: INSIDE, NEAR THE DECK MECHANISM.
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
BEAM.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications
to this equipment may cause harmful interference unless the modifications are expressly approved in the
manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA
FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your
local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning
chemical wastes.
Make your contribution to the environment!!!
• Used up batteries do not belong in the dust bin.
• You can dispose of them at a collection point for used up batteries or special wastes.
Contact your council for details.
For Customer Use:
Read carefully the information located at the back of this unit and enter below the Model No. and the Serial No. Retain this
information for future reference.
Model No. ____________________
Serial No. ____________________
–
–
2
EN
IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions- The safety and operating instructions
should be retained for future reference.
3. Heed Warnings - All warnings on the appliance and in the
operating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug this video product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the
possibility of the loss of an authorization code for a CATV
converter, is not intended to be unplugged by the user for
cleaning or any other purpose, may exclude the reference
to unplugging the appliance in the cleaning description
otherwise required in item 5.
6. Attachments - Do not use attachments not recommended
by the video product manufacturer as they may cause
hazards.
7. Water and Moisture- Do not use this video product near
water, for example, near a bath tub, wash bowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, and the like.
8. Accessories - Do not place this video product on an
unstable cart, stand, tripod, bracket, or table. The video
product may fall, causing serious injury to a child or adult,
and serious damage to the appliance. Use only with a
cart, stand, tripod, bracket, or table recommended by the
manufacturer, or sold with the video product. Any mounting of the appliance should follow the
manufacturer's instructions and should
use a mounting accessory recommended
by the manufacturer. An appliance and
cart combination should be moved with
care. Quick stops, excessive force, and
uneven surfaces may cause the appliance and cart combination to overturn.
9. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of
the video product and to protect it from overheating, and
these openings must not be blocked or covered. The
openings should never be blocked by placing the video
product on a bed, sofa, rug, or other similar surface. This
video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation
is provided or the manufacturer's instructions have been
adhered to.
10. Power Sources - This video product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or
local power company. For products intended to operate
from battery power, or other sources, refer to the
operating instructions.
11. Grounding or Polarization - This video product is
equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). This plug
will fit into the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully into the
outlet, try reversing the plug. If the plug should still fail to
fit, contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.
12. Power Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. Outdoor Antenna Grounding - If an outside antenna or
cable system is connected to the video product, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANSI/
NFPA No. 70, provides information with regard to proper
–
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode. (Fig. A)
14. Lightning - For added protection for this video product
during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This
will prevent damage to the video product due to lightning
and power-line surges.
15. Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with
them might be fatal.
16. Overloading - Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17. Object and Liquid Entry - Never push objects of any kind
into this video product through any openings as they may
touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of
any kind on the video product.
18. Servicing - Do not attempt to service this video product
yourself as opening or removing covers may expose you
to dangerous voltage or other hazards. Refer all servicing
to qualified service personnel.
19. Damage Requiring Service - Unplug this video product
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the
c. If the video product has been exposed to rain or water.
d. If the video product does not operate normally by
e. If the video product has been dropped or damaged in
f. When the video product exhibits a distinct change in
20. Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or have
the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other
hazards.
21. Safety Check - Upon completion of any service or repairs
to this video product, ask the service technician to perform safety checks to determine that the video product is
in proper operating condition.
22. Heat - This video product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.
–
3
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC – NATIONAL ELECTRICAL CODE
S2898A
ANTENNA
LEAD
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMP
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
video product.
following the operating instructions. Adjust only those
controls that are covered by the operating instructions
as an improper adjustment of other controls may result
in damage and will often require extensive work by a
qualified technician to restore the video product to its
normal operation.
any way.
performance this indicates a need for service.
EN
Precautions
Location and Handling
•
Do not stand this unit up vertically. Install this unit in a horizontal and stable position. Do not place anything directly on
top of this unit. Do not place this unit directly on top of the TV.
• Depending on the TV, noise or disturbance of the picture
and/or sound may be generated if this unit is placed too
close to your TV. In this case, please ensure enough space
Precautions
between your TV and this unit.
• Do not cover or place this unit in enclosed spaces to prevent
excessive temperature build up.
Do not place this unit in direct sunlight, or near heat sources.
•
• Depending on the environment, the temperature of this unit
may increase slightly. This is not a malfunction.
• Keep this unit away from strong magnetic objects.
• Do not place any object containing water or other liquids on
this unit. In the event that liquid should enter the cabinet,
unplug this unit immediately and contact the retailer or an
Authorized Service Center immediately.
• Do not remove this unit cabinet. Touching parts inside the
cabinet could result in electric shock and/or damage to this
unit. For service and adjustment inside the cabinet, call a
qualified dealer or an Authorized Service Center.
• Be sure to remove disc and video tape and unplug the AC
power cord from the output before carrying this unit.
Avoid the Hazards of Electrical Shock and Fire
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from
AC wall outlet. Grasp it by the plug.
• If, by accident, water is spilled on this unit, unplug the power
cord immediately and take the unit to our Authorized Service
Center for servicing.
•
Do not put your fingers or objects into the unit cassette holder.
Moisture Condensation Warning
Moisture may form inside this unit under the following conditions:
• Immediately after a heater is turned on.
• In a steamy or humid room.
• When this unit is suddenly moved from a cold to warm
environment.
If moisture forms inside this unit, it may not operate
properly or damage the video tape. In such case, turn on
the power and wait for more than 2 hours for the moisture to
evaporate.
About Copyright
Unauthorized copying, broadcasting, public performance and
lending of discs are prohibited.
This product incorporates copyright protection technology that
is protected by U.S. patents and other intellectual property
rights. Use of this copyright protection technology must be
authorized by Macrovision, and is intended for home and
other limited viewing uses only unless otherwise authorized by
Macrovision. Reverse engineering or disassembly is
prohibited.
Symbols Used in This Manual
The following symbols appear in some headings in this
manual.
: Description refers to playback or recording of
video cassette tapes.
:
Description refers to playback of DVD-Video discs.
: Description refers to playback of Audio CDs.
: Description refers to playback of MP3 files.
Maintenance
SERVICING
• Please refer to relevant topics on the “Troubleshooting
Guide” on page 23 before returning the product.
• If this unit becomes inoperative, do not try to correct the
problem by yourself. There are no user-serviceable parts
inside. Turn off, unplug the power plug, and please call
our help line mentioned on the front page to locate an
Authorized Service Center.
CLEANING THE CABINET
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
CLEANING DISCS
• When a disc becomes dirty, clean it with a cleaning cloth.
Wipe the disc from the center to out. Do not wipe in a circular motion.
•
Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic
spray intended for analog records.
CLEANING THE DISC LENS
• If this unit still does not perform properly although you refer
to the relevant sections and to “Troubleshooting Guide” in
this Owner’s Manual, the laser optical pickup unit may be
dirty. Consult your dealer or an Authorized Service Center
for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• When you handle a disc, hold it by its edge and try not to
touch the surface of the disc.
• Always store the disc in its protective case when it is not
used.
AUTO HEAD CLEANING
• Automatically cleans video heads as you insert or remove a
cassette, so you can see a clear picture.
• Playback picture may become blurred or interrupted while
the TV program reception is clear. Dirt accumulated on the
video heads after a long period of use, or the usage of rental
or worn tapes can cause this problem. If a streaky or snowy
picture appears during playback, the video heads in your
unit may need to be cleaned.
1. Please visit your local Audio/Video store and purchase a
good quality VHS Video Head Cleaner.
2. If a Video Head Cleaner does not solve the problem,
please call our help line mentioned on the front page to
locate an Authorized Service Center.
Hint
• Remember to read the instructions along with the video head
cleaner before use.
• Clean video heads only when problems occur.
Note to CATV system installer
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground should be
connected to the grounding system of the building,
as close to the point of cable entry as practical.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
–
–
4
EN
About the Video Cassettes and Discs
Playable Video Cassettes
Use only cassettes marked
Playable Discs
Playable
discs
DVD-Video
*1, 2, 4, 6
DVD-RW
DVD-R
*1, 3, 4, 5, 6,
8, 9
DVD+RW
DVD+R
*1, 3, 4, 5, 6,
7, 8, 9
Audio CD
*4, 6
CD-RW
CD-R
*4, 5, 6, 8, 9
Mark (logo)Region code
with this unit.
or
Recorded
signals
Digital video
(MPEG2)
Digital audio
or
MP3
Disc sizeDisc types
12 cm
or
8 cm
Audio CD
Example
Chapter 1 Chapter 2Chapter 1
Example
Title 1Title 2
Chapter 3 Chapter 4
Track 1 Track 2Track 5
Track 3
12 cm
or
8 cm
MP3
Example
Group 1Group 2
Track 1
Track 3
Track 2Track 1
Track 4
Track 4
Precautions
Chapter 2
Track 6
Track 2
is a trademark of DVD Format/Logo Licensing Corporation.
If you cannot play back a disc which bears one of the marks above, check the following notes.
*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back.
*2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers.
*3: Discs Recorded in the VR (Video Recording) format cannot be played back.
*4: Scratched or stained discs may not be played back.
*5: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or
special properties of discs.
*6: You can play back discs which bear the marks above. If you use non-standardized discs, this unit may not play them
back. Even if they are played back, the sound or video quality will be compromised.
*7: Only the discs recorded in the video format and finalized can be played back.
Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be played back at
all. (the picture or sound may not be smooth, etc.)
*8:
If the recorded portion of the disc is too small (less than 2 3/16 inches (55 mm) across), it may not play back properly.
*9: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly.
Unplayable Discs
NEVER play back the following discs. Otherwise, malfunction may result!
DVD-RAM / DVD-Audio / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL / DTS-CD / DVD-ROM for
personal computers / CD-ROM for personal computers
On the following disc, the sound MAY NOT be heard.
Super Audio CD
NOTE: Only the sound recorded on the normal CD layer can be delivered.
The sound recorded on the high density Super Audio CD layer cannot be delivered.
Any other discs without compatibility indications
–
5
–
EN
Setup
Connections
Please refer to “Basic TV Connection” on the front page before you use this unit.
RF Output Channel
If channel 3 has been already occupied
for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [SOURCE] on the unit so that the
VCR SOURCE light is lit.
•
If noise appears on the TV screen, press
[VCR/TV] on the remote control.
4) Press [PLAY B] once.
5) After a few seconds, press and hold
[PLAY B] on the unit for 3 seconds.
• The RF output channel will change to
channel 4 from channel 3 and you will
see a playback picture.
• When a picture does not appear on the
TV screen, repeat step 4.
6) Press [STOP C] to stop playback.
Hint
• The RF output channel does not
change when you adjust tracking during playback. In case RF
output channel changes, you
can easily switch it back. Start
the playback again then press
and hold [PLAY B] on the unit
for 3 seconds.
Setup
Hint for Cable Box or Satellite Box
(Back of DVD/VCR)
ANT-IN
ANT-OUT
RF cable
(supplied)
Satellite or
Cable TV
signal
(Cable box or
Satellite box)
IN
OUT
Select this connection when you want to view or record a
scrambled channel. With this connection, channels cannot be
changed on the unit. You can view or record ONLY the channels
you have selected on the cable box or the satellite box.
•
While you are recording, only the recorded channel can be viewed.
Connection to an Audio System
Method 1
Audio
DVD/VCR
Stereo system
Audio cable
(supplied)
AUDIO OUT
(Analog)
DIGITAL
AUDIO OUT
(DVD mode only)
LR
AUDIO OUT
L
R
or
DVD
AUDIO
S-VIDEO
OUT
L
R
VCRDVD/VCR
COMPONENT
VIDEO OUT
OUT
Analog audio
input jacks
(Back of TV)
To select channels of the cable box or satellite box
1) Turn on the unit by pressing [STANDBY-ON], then press
[VCR/TV]. The STANDBY-ON indicator on the front panel
will light, then press [SKIP/CH. G/K, H/L] to select
channel 3 or 4 (the same channel as the output channel of
the cable box or satellite box).
• If you use the channel 4, you need to change the unit’s
RF output to channel 4. Refer to “RF Output Channel”.
2) At the TV, select channel 3 or 4 (the same channel as you
have selected at step 1).
3) On the cable box or satellite box, select the channel you
want to view or record.
Method 2
Dolby Digital decoder,
MD deck or DAT deck
COAXIAL
Digital audio
input jack
Audio Coaxial Digital cable
(commercially available)
DVD
AUDIO
COMPONENT
S-VIDEO
VIDEO OUT
OUT
OUT
DIGITAL
DIGITAL
AUDIO OUT
COAXIAL
AUDIO OUT
Connection
Setting
Connecting to a Dolby Digital decoder
for Dolby Digital audio output.
Connecting to the other equipment
(an MD deck or DAT deck etc.)
without Dolby Digital decoder.
* To complete these settings, refer to pages 20-21.
SETUP > AUDIO >
DOLBY DIGITAL
BITSTREAM
Hint
• The audio source on a disc in a Dolby Digital Multi channel
surround format cannot be recorded as digital sound by an MD or
DAT deck.
• By hooking this unit up to a Multi channel Dolby Digital decoder,
you can enjoy high-quality Dolby Digital Multi channel surround
sound as heard in the movie theaters.
• Playing a DVD using incorrect settings may generate noise
distortion and may also damage the speakers.
–
–
6
PCM
EN
O
Connection to a TV
TV
DVD/VCR
DIGITAL
AUDIO OUT
COAXIAL
AUDIO OUT
(Analog)
Basic Audio
Audio cable
(supplied)
DVDVCR
DVD/VCR
COMPONENT
AUDIO OUT
AUDIO
S-VIDEO
VIDEO OUT
OUT
OUT
LY
AUDIO IN
L
R
C
B
VIDEO IN
VIDEO OUT
R
C
R
DIGITAL
AUDIO OUT
AUDIO IN
LR
AUDIO OUT
L
R
or
DVD
AUDIO
OUT
L
R
S-VIDEO
OUT
Method 1
Good picture
VIDEO IN
Video cable
(supplied)
VCRDVD/VCR
ANT-IN
ANT-OUT
VCRDVD/VCR
COMPON
VIDEO
VIDEO OUT
VIDEO OUT
S-Video cable
(commercially
Better picture
available)
DIGITAL
AUDIO OUT
COAXIAL
S-VIDEO OUT
Method 2
S-VIDEO IN
DVD
COMPONENT
AUDIO
S-VIDEO
VIDEO OUT
OUT
OUT
Method 3
Best picture
Component Video cable
(commercially available)
DIGITAL
AUDIO OUT
COMPONENT VIDEO OUT
COAXIAL
DVD
AUDIO
OUT
COMPONENT
VIDEO IN
Y
C
B
R
C
COMPONENT
S-VIDEO
OUT
VIDEO OUT
Y
C
B
C
R
Hint
• Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy
protection system.
• The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT and COMPONENT VIDEO OUT jacks are only useful in DVD mode.
After you have completed connections
Press the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel
(usually near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual accompanying your TV.
INPUT MODES FOR COMMON TV BRANDS
Listed below are inputs for common brand name TV’s.
Setup
Admiral: AUX
Curtis Mathis: LINE1, LINE2, 00, 90, 91, 92, 93
GE: INPUT, TV/VCR, 00, 90, 91, 92, 93
Hitachi: INPUT, AUX
JVC: VIDEO, VIDEO1, VIDEO2, VIDEO3
Kenwood: AUX
LXI-Series: 00
Magnavox: AUX CHANNEL
If channel 3 has been already occupied for broadcasting,
see “RF Output Channel” section on page 6.
Select your language when turning this unit on for the first time.
2
Then press [
STANDBY-ON
Press [B] to start Auto Set Up.
3
mainly based on the remote control.
B] to go to next step.
or
Setup
Do you connect the cable from the cable box or the satellite box to
the unit’s ANT-IN jack?
YES
Yes Press [MENU] to exit.
•
Refer to “Hint for Cable Box or Satellite Box” section on page 6.
No
Please wait for a few minutes.
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G///K, H//L] (or [CHANNEL K///L]).
• If “AUTO SET UP” appears on the TV screen again, check the
cable connections. Then, press [B] once again.
Hint
• Repeat these steps only if either there was a power failure or this
unit has been unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using the Number buttons or
[
SKIP/CH. G/K, H/
Notes for using the Number buttons:
• When selecting cable channels which are higher than 99,
enter channel numbers as a three-digit number.
(for example: 117, press [1], [1], [7])
• You must precede single-digit channel numbers with a zero.
(for example: 02, 03, 04 and so on)
To Add or Delete Channels
Press [MENU] to select “CHANNEL SET UP”.
1
Then press [B] to go to next step.
MENU
• If the clock is not set, the “CLOCK SET” screen appears when
you press [MENU]. In this case, press [MENU] again.
Select “MANUAL SET UP”.
2
Then press [B] to go to next step.
Select the channel to be added or deleted.
3
Select “ADD” or “DELETE”.
4
To exit the menu
5
L].
VCR
or
or
or
or
or
CLEAR/
C. RESET
After scanning...
or
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
CH 01
AUTO SET UP
NO
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
MANUAL SET UP
CHANNEL 30 (CATV)
ADD
MANUAL SET UP
CHANNEL 30 (CATV)
DELETE
To Preset the Channel Again
1) Press [MENU] until the main menu appears.
Select “CHANNEL SET UP” by using
2)
3)
Select “AUTO SET UP” by using [K//L], then press [B]. After
[K//L]
, then press
scanning, the tuner stops on the lowest memorized channel.
To Change the On-Screen Language
1)
Press
[MENU]
until the main menu appears.
2) Select “LANGUAGE SELECT” by using [K/L], then
press [B].
3) Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by
using [K/L] then press [CLEAR/C.RESET].
Hint
• If you accidentally select Spanish or French and need English: Press
[MENU] and choose SELEC. IDIOMA or SELECTION LANGUE.
Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].
• To add or delete channels in this unit, [SKIP/CH. G/K, H/L]
button works on the channel number memorized in this unit, [K/L]
works on all.
Clock Setup
VCR
Press [MENU] and select “CLOCK SET”.
1
Then press [B] to go to next step.
MENU
or
• If the clock is not set, the CLOCK SET screen appears when
you press [MENU]. In this case, go to step 2.
Select the current month.
2
Then press [B] to go to next step.
or
Select the current day.
3
Then press [B] to go to next step.
or
Select the current year.
4
Then press [B] to go to next step.
or
Select the current hour.
5
Then press [B] to go to next step.
or
Select the current minute.
6
Then press [B] to go to next step.
or
Select “AM” or “PM”.
7
or
To exit the CLOCK SET screen
8
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
Hint
• To go back one step, press [s] (during steps 2 to 7).
• Your clock setting will be lost if either there is a power failure or this
unit has been unplugged for more than 30 seconds.
–
–
8
CLOCK SET
CLOCK SET
CLOCK SET
CLOCK SET
CLOCK SET
CLOCK SET
[B]
EN
.
Function Overview
VCRDVD
SOURCE
Front Panel Indicator
Lights up during a recording.
Blinks when a recording is paused.
Lights up when the disc is inserted.
OPEN/
CLOSE
Lights up when the inserted
disc is being played back.
Blinks when an unacceptable
disc is inserted.
VIDEOAUDIO STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORDCHANNEL
IR
Lights up when power is on.
Lights up when the Timer Recording
or an OTR recording has been set.
VCR / DVD Switching
You must select which component you wish to operate with
[SOURCE] at first, as this product is a combination of a VCR
and a DVD player.
VCR MODE
Press [VCR] on the remote control.
(Verify that the VCR SOURCE light is lit.)
DVD MODE
Press [DVD] on the remote control.
(Verify that the DVD SOURCE light is lit.)
Hint
• Pressing only [SOURCE] on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode on
the remote control.
VCRDVD
DISC INPLAYREC TIMER
PREVSOURCESTOP PLAY NEXT
Lights up when this unit is in the DVD mode.
Lights up when this unit is in the VCR mode.
OPEN/
CLOSE
VCR DVD
CHANNEL
DISC IN PLAY
PREVSOURCESTOP PLAY NEXT
VCR button
STANDBY-ON
SPEED AUDIO
123
456
789
0
DISPLAY VCR DVD PAUSE
DVD button
SOURCE button
DVD SOURCE light
RECORD
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE
ANGLE
T-SET
VCR SOURCE light
+10
PLAY
STOP
ENTER
SEARCH
MODE
REPEAT A-B
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
SLOW
RETURN
CLEAR/
C. RESET
Setup
Front & Rear Terminals
32
DVD
DIGITAL
AUDIO
OUT
AUDIO OUT
COAXIAL
L
R
1
10
9
1: DVD AUDIO OUT (analog) jacks
Connect the supplied audio cable here through the audio in jacks of
a television or other audio equipment. (DVD only)
2: DVD/VCR AUDIO OUT jacks
Connect the supplied audio cable here through the audio in jacks of
a television or other audio equipment.
3: AUDIO IN jack
Connect audio cable coming from the audio out jack of a camcorder,
another VCR or an audio source here.
4: ANT-IN jack
Connect your antenna or cable box here.
5: ANT-OUT jack
Connect the supplied RF cable to the antenna input jack of a
television.
DVD/VCR
COMPONENT
AUDIO OUT
S-VIDEO
VIDEO OUT
OUT
DIGITAL
AUDIO OUT
Y
COAXIAL
C
B
VIDEO OUT
C
R
8 76
VCR
DVDVCR
DVD/VCR
COMPONENT
AUDIO OUT
AUDIO
S-VIDEO
VIDEO OUT
OUT
OUT
L
L
AUDIO IN
C
B
VIDEO OUT
R
C
R
R
VIDEO IN
LY
AUDIO IN
R
VIDEO IN
[Rear Panel]
ANT-IN
ANT-IN
ANT-OUT
4
ANT-OUT
VIDEOAUDIO STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD
6
3
[Front Panel]
5
6: VIDEO IN jack
Connect a cable coming from the video out jack of a camcorder,
another VCR or an audio-visual source (laser disc player, video disc
player, etc.) here.
7: DVD/VCR VIDEO OUT jack
Connect the supplied video cable here through the video in jack of a
television.
8: COMPONENT VIDEO OUT jacks
Connect optional COMPONENT VIDEO cables here through the
COMPONENT VIDEO in jacks of a television. (DVD only)
9: S-VIDEO OUT jack
Connect an optional S-VIDEO cable here through the S-VIDEO in
jack of a television. (DVD only)
10: DIGITAL AUDIO OUT COAXIAL jack
Connect an optional coaxial digital audio cable here through the
coaxial digital audio in jack of a decoder or audio receiver. (DVD only)
–
–
9
REC TIMER
EN
Remote Control
STANDBY-ON
SPEED AUDIO
123
456
789
+10
0
DISPLAY VCRDVDPAUSE
PLAY
STOP
RECORD
ENTER
MENU
Setup
SETUP TOP MENU
MODE ZOOM
SUBTITLE
SEARCH
MODE
ANGLE
REPEAT A-B
T-SE T
Installing the Batteries for
the Remote Control
Install two AA batteries (supplied)
matching the polarity indicated inside
battery compartment of the remote
control.
1
2
Keep in mind the following when using
the remote control:
•
Make sure that there is no obstacle
between the remote control and the
remote sensor on the unit.
• The maximum operable ranges from
the unit are as follows.
- Line of sight: approx. 23 feet (7m)
- Either side of center:
- Above:
- Below:
approx. 16 feet (5m) within 30°
approx. 16 feet (5m) within 15°
approx.
10 feet (3m) within 30°
Hint
• Do not mix alkaline and manganese
batteries.
• Do not mix old and new batteries.
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
SLOW
RETURN
CLEAR/
C. RESET
Button
(Alphabetical order)
3
Disc/Tape
123
456
789
0
A-B
ANGLE
AUDIO
CLEAR/
C. RESET
DISPLAY
DVD
ENTER
MENU
MODE
OPEN/CLOSE
/EJECT
PAUSE
PLAY
RECORD
REPEAT
RETURN
SEARCH
MODE
SETUP
SKIP/CH.
SKIP/CH.
SLOW
SPEED
STANDBY-ON
STOP
SUBTITLE
T-SET
TOP MENU
VCR
VCR/TV
ZOOM
• To select chapter or title
directly.
+10
•
To search forward/backward
through a disc.
•
To begin slow forward
playback in the pause mode.
• To repeat between your
chosen point of A and B.
• To select camera angles on
a disc.
• To select audio languages
on a disc.
• To remove status number in
program input.
• To clear the numbers
entered incorrectly.
• To cancel the point for A-B
repeat.
• To display the current disc
mode.
•
To select the DVD output mode.
• To activate the remote
control in DVD mode.
• To move the cursor and
determine its position.
•
To call up the Menu on a disc.
• To arrange the playing order
or play randomly.
• To set black level on/off.
• To set virtual surround
on/off.
• To open or close the disc
tray.
• To pause disc playback.
• To advance playback one
frame at a time.
• To select track directly. (CD)
• To select group/track
directly. (MP3)
• To search forward/backward
through a disc.
•
To repeat between your
chosen point of A and B.
• To select STEREO, L-ch or
R-ch. (CD)
• To remove status number in
program input.
• To clear the numbers
entered incorrectly.
• To cancel the point for A-B
repeat.
• To display the current disc
mode.
To select the DVD output mode.
•
• To activate the remote
control in DVD mode.
• To move the cursor and
determine its position.
• To arrange the playing order
or play randomly.
•
To set virtual surround on/off.
• To open or close the disc
tray.
• To pause disc playback.
• To select channel.
• The +10 button has no
effect in VCR mode.
• To forward/backward a tape.
• To exit the VCR Menu.
• To reset the tape counter.
• To display the current time,
tape counter, and channel.
• To call up the VCR Menu.
• To eject the video
cassette from the VCR.
• To pause tape playback or
recording.
• To advance playback one
frame at a time.
• To begin disc playback.• To begin disc playback.• To begin tape playback.
• To start a recording or One
Touch Recording.
• To call up the index or time
search menu.
• To change channels.
• To adjust the tracking
manually during playback.
• To view the tape in slow
motion.
• To select the recording
speed.
• To play a chapter or title
repeatedly.
• To return to the previous
operation in menu.
• To search chapter, title or
time.
• To call up the DVD setup
menu.
• To skip chapters or titles.
• To play a track or disc
repeatedly. (CD)
• To play a track, group or
disc repeatedly. (MP3)
• To return to the previous
operation in menu.
• To search track.
• To search time. (CD)
• To search groups. (MP3)
• To call up the DVD setup
menu.
• To skip tracks. (CD)
• To skip groups or tracks.
(MP3)
• To turn the unit on/off.• To turn the unit on/off.• To turn the unit on/off.
• To stop playback.• To stop playback.
• To select subtitles on a disc.
• To call up the Top Menu on
a disc.
• To select DVD position or
TV position.
• To magnify part of a picture.
(x2 / x3 / x4 / x1/2)
–
–
10
• To select CD/MP3 position
or TV position.
• To stop playback or
recording.
To put the VCR into standby
•
mode for a Timer Recording.
• To select the VCR output mode.
• To activate the remote
control in VCR mode.
• To select VCR position or
TV position.
•
To select an item
on the VCR Menu.
•
To advance to the
next VCR Menu.
•
To go back one
step during clock
and timer setting.
EN
DVD modeVCR mode
VCR Functions
VCR
VCR
VCR
Playback
Before:
Turn on the TV and set it to channel 3.
• If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section on page 6.
1
Insert a video cassette
into this unit.
3 To stop playback4 To eject the cassette
Other Operations
To cue or review picture during playback (Picture Search)
Use [g] or [h ]([ F.FWDg] or [REW h]).
• Press it again and the unit will search in super high speed.
(in the SLP mode only)
To freeze the picture on TV screen during playback (Still mode)
Press [PAUSE F]. Each time you press the button, the
picture will be forwarded by one frame.
•
If the picture begins to vibrate vertically in the still mode,
stabilize the picture by using
[
CHANNEL K/L]).
• If the picture is distorted or rolling vertically, adjust the
vertical hold control on your TV if equipped.
Hint
• Still/Slow mode will be automatically canceled after 5 minutes to prevent damage to the tape and the video head.
• To return to playback from the Picture Search/Still/Slow mode, press [PLAY B].
VCR
STOP
2 To start playback
PLAY
OPEN/CLOSE
/EJECT
STANDBY-ON
2
SPEED AUDIO
123
456
789
0
DISPLAY VCR DVD PAUSE
PLAY
STOP
+10
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
SLOW
4
VIDEOAUDIO STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD
3
1
342
Counter Reset
Press [CLEAR/C.RESET].
To play back in slow motion (Slow mode)
Press [SLOW] during playback or the still mode.
• If the noise bars appear on the TV screen, you can reduce it
by using [SKIP/CH. G/K, H/L] (or [
Auto Rewind
[SKIP/CH. G/K, H/L] (or
When a tape reaches its end during playback, fast-forward
or recording (except Timer Recording and One Touch
Recording), the tape will automatically rewind to the beginning.
After rewinding finishes, the unit will eject the tape.
REC TIMER
IR
Hint
•
When a tape without
record tab is inserted,
the unit will start
playback automatically.
•
Tracking will be
automatically adjusted
upon playback.
To adjust the tracking
manually, press
CH. G/K, H/L] (or
CHANNEL K/L]
[
CHANNEL K/L]
[SKIP/
).
).
VCR Functions
Index Search
You can skip the program backward and forward by the Index
Mark.
VCR
Press [SEARCH MODE] once.
1
To select Index Mark
2
To rewind
3
To fast forward
After searching, it automatically
4
starts playback.
• Insert a tape into this unit.
SEARCH
MODE
or
Beginning
of the tape
Pro.1 Pro.2 Pro.3 Pro.4 Pro.5
0201010203
INDEX SEARCH
– –
INDEX SEARCH
0 3
CURRENT PROGRAM
ss
BB
PLAYB
01 ~ 20
INDEX MARK
End of
the tape
Hint
•
The Index Mark will be made automatically at the beginning of each recording.
• The time gap between Index Marks should be greater than 1 minute
for SP mode, 2 minutes for LP mode and 3 minutes for SLP mode.
Time Search
You can search backward and forward a specific length of
time on a tape.
Press [SEARCH MODE] twice.
1
Select the desired length of time for fast forwarding or
2
rewinding.
To rewind
3
To fast forward
After searching, it automatically starts playback.
4
Hint for Index Search & Time Search
• These functions are not available during recording.
• Press [STOP C] to stop the search.
• If a tape ends during a search, your search will be canceled and
the tape will rewind to the beginning.
–
–
11
VCR
• Insert a tape into this unit.
SEARCH
MODE
or
TIME SEARCH
– : – –
TIME SEARCH
2 : 5 0
(1 minute~9 hours and 59 minutes)
PLAYB
0:01~ 9:59
ss
BB
EN
(
Auto Repeat
VCR
VCR
VCR
This function will playback a tape repeatedly from the beginning when the tape reaches the end.
Press [MENU], and choose
1
“AUTO REPEAT” during playback.
VCR
MENU
- M E N U -
TIMER PROGRAMMING
B AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
or
LANGUAGE SELECT
Press [B] for
2
“AUTO REPEAT”, “ON” or “OFF”.
Hint
• To cancel Auto Repeat, follow step 1 above. Then, press [B] so that “OFF” appears beside “AUTO REPEAT”. Press [CLEAR/C.RESET] to exit.
• If menu remains on the TV screen after step 2, press [CLEAR/C.RESET] to exit.
• The Auto Repeat playback will start automatically if you select “AUTO REPEAT” to “ON” in the stop mode.
Recording
Recording & OTR (One Touch Recording)
Before:
Turn on the TV and set it to channel 3.
• If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section on page 6.
VIDEOAUDIO STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORDCHANNEL
Accidental erasure prevention
To prevent accidental recording on a recorded
cassette, remove its record tab. To record on
RETURN
it later, cover the hole with adhesive tape.
STANDBY-ON
123
456
789
2
DISPLAY VCR DVD PAUSE
RECORD
5
MENU
4
SETUP TOP MENU
You CAN NOT dub a DVD to a videotape.
To stop recording temporarily (Pause mode)
Press [PAUSE F].
• During the rec-pause mode, five C marks appear on the TV screen. Each C
mark represents one minute.
• Press it again to resume recording.
• Pause mode will be automatically canceled after 5 minutes to prevent damage
to the tape and the video head.
Hint
• If you want to watch one channel while recording another...
1) If noise appears on the TV screen, press [VCR/TV] to put the unit in TV position.
2) You cannot record one channel while watching another if you have a cable box or
satellite receiver.
5 6
- M E N U -
TIMER PROGRAMMING
B AUTO REPEAT [ON]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
1
IR
2
OPEN/
CLOSE
VCRDVD
DISC INREC TIMER
PREVSOURCESTOP
4
Record tab
Timer Recording
VCR
•
Press [MENU], then select “TIMER PROGRAMMING”.
1
MENU
Insert a tape with its record tab into the unit.
- M E N U -
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
TIMER PROGRAMMING
PROG 12345678
DATE
START TIME
END TIME
CHANNEL
REC SPEED
Available program number flashes.
Select an empty program number.
2
Then press [B] to go to next step.
or
Select “ONCE”, “DAILY” (Mon-Fri), or “WEEKLY”.
3
Then press [B] to go to next step.
or
PROGRAM NUMBER 1
DATE – – / – –
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
PROGRAM NUMBER 1
B ONCE
DAILY
WEEKLY
–
12
Select the desired date.
4
Then press [B] to go to next step.
or
or
• You can set a program one year in advance.
Select the desired start time (hour).
5
Then press [B] to go to next step.
or
or
–
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME – – : – – – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 – –
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
EN
Select “AM” or “PM”.
6
Then press [B] to go to next step.
or
Repeat the procedure in steps 5 and 6 to set the end time.
7
Select the desired channel.
8
Then press [B] to go to next step.
or
• If you have connected the unit to a cable box or satellite
box as the connection on page 6, select the VCR to
channel 3 or 4 (the RF output channel of the VCR). Then,
select the desired channel at the cable box or satellite box.
Leave the cable box or satellite box on for Timer Recording.
Select the desired recording speed, then press
9
[CLEAR/C.RESET].
CLEAR/
or
• To set another program after step 9, press [
Then, continue with step 2.
C. RESET
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME – – : – – – –
CHANNEL – –
REC SPEED – –
AM
B PM
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED – –
ONE TIME PROGRAM
PROGRAM NUMBER 1
DATE 1 0 / 2 3 MON
START TIME 0 7 : 3 0 PM
END TIME 0 8 : 3 0 PM
CHANNEL 1 6
REC SPEED SP
B SP SLP
B].
Press [SUBTITLE/T-SET] to set timer standby mode.
10
• TIMER indicator on the front panel lights up. The unit will
change to the DVD mode.
SUBTITLE
T-S E T
Hint
• To go back one step, press [s] during steps 3 to 9.
To Check, Correct or Cancel a Timer Program
1) Press [SUBTITLE/T-SET] then, [VCR] on the remote
control.
2) Select main menu by pressing
3) Select “TIMER PROGRAMMING” by using [K/L], then
press [B].
4) Select the program number which you want to check by
using [K/L]. The details of the program you selected will
appear on the TV screen.
• Go to the digit you want to change by using [s / B].
Then, enter correct numbers by using [K/L].
• You may cancel the entire program by pressing [s]
while the program number blinks.
5) Press [CLEAR/C.RESET] to exit.
6) Press [SUBTITLE/T-SET] to return to timer standby
mode.
To cancel a Timer Recording in progress
Press [STOP/EJECT CA] on the unit.
[MENU]
.
Hints for OTR and Timer Recording
• Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR
mode, then press [SUBTITLE/T-SET].
• If a tape is not in the unit or does not have the record tab, TIMER indicator on the front panel blinks and Timer Recording
cannot be performed. Please insert a recordable tape.
• When Timer Recordings are set, TIMER indicator on the front panel lights up. To use the VCR as usual until the time for the
recording, press [SUBTITLE/T-SET] so that TIMER indicator lights off. Press [VCR/TV] to choose the VCR position. Select
either VCR or DVD mode, then continue with the other features as described in this manual.
After an OTR or a Timer Recording has been set, this unit operates as follows:
• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [SUBTITLE/T-SET] on the
remote control or [STOP/EJECT CA] on the unit, then press [VCR] to activate the VCR function again.
• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed.
• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT CA] on the unit, then
press [VCR] to activate the VCR function again.
• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after
you canceled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you
operate.
When an OTR or a Timer Recording is completed...
• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically,
and TIMER indicator on the front panel lights to indicate the unit is in the timer standby mode.
• TIMER indicator on the front panel flashes if there are no more Timer Recordings on standby.
• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR functions will be
unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording.
•
Press [STOP/EJECT CA] on the front panel or [SUBTITLE/T-SET] on the remote control to use the VCR when the unit is
off.
• Press [SOURCE] on the front panel or [VCR] on the remote control to use the VCR when the unit is on. In case Timer
Recording is in standby mode, press [STOP/EJECT CA] on the front panel or [SUBTITLE/T-SET] on the remote control,
and then press [SOURCE] on the front panel or [VCR] on the remote control.
If you want to use the DVD player during a Timer Recording or while TIMER indicator on the front panel is on or blinking.
• Press [STANDBY-ON] to turn on the unit. Press [DVD] on the remote control to choose DVD mode, then continue with the
other DVD features as described in this manual.
NOTE (for Timer Recording) :
• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.
VCR Functions
–
13
–
EN
Copying a Video Tape
Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.
(Back of TV)
(Back of another source)
(Back of DVD/VCR*)
VCRDVD/VCR
COMPONENT
AUDIO OUT
VIDEO OUT
or
AUDIO OUT
Y
L
AUDIO IN
C
B
R
VIDEO IN
VIDEO OUT
VIDEO OUT
C
R
Audio/Video cables
(commercially available)
1) Insert a pre-recorded tape into another VCR for playing.
2)
Insert a tape with its record tab into this unit for recording.
3) Press [SPEED] on the remote control of the recording
unit to select the desired recording speed (SP/SLP).
4) Select the “L1” or “L2” position on the recording unit.
• To use the input jacks on the back of this unit, select
“L1” position by pressing [0], [0], [1] on the remote
control or [
CHANNEL K/L]
on this unit.
• To use the input jacks on the front of this unit, select
“L2” position by pressing [0], [0], [2] on the remote
VCR Functions
control or [
5) Press [RECORD] on the recording unit.
CHANNEL K/L] on
this
unit
6) Begin playback of the tape in another source.
7) To stop recording, press [STOP/EJECT CA] on the
recording unit, then stop playback of the tape in another
source.
ANT-IN
1
Connect
ANT-OUT
.
DIGITAL
AUDIO OUT
COAXIAL
DVDDVD/VCR VCR
COMPONENT
AUDIO OUT
AUDIO
S-VIDEO
VIDEO OUT
OUT
OUT
L
Y
L
C
B
R
VIDEO OUT
R
C
R
AUDIO IN
VIDEO IN
ANT-IN
ANT-OUT
2
Connect
RF cable
(supplied)
*Front input jacks are also available
Hint
• For best results during dubbing, use the front panel controls
whenever possible. The remote control might affect another
source’s operation.
• Always use video-quality shielded cables with RCA-type
connectors. Standard audio cables are not recommended.
• You can use a video disc player, satellite receiver or other
audio/video component with Audio / Video outputs.
• “L1” or “L2” is found below the lowest memorized channel.
(Example: CH02)
• “L2” input jacks are on the front of this unit.
–
14
–
EN
DVD Functions
Operations described in this section are mainly based on the remote control use. Some operations can be carried out on main unit.
Playback
Before: Turn on the TV, amplifier and any
other equipments which are connected
to this unit. Make sure the TV and audio
receiver (commercially available) are set
to the correct channel.
DVDVD
2
⇒
(
Press [STANDBY-ON] to turn on
1
Page 16
)
the DVD/CD Player.
Press [OPEN/CLOSE A] and insert
2
a disc with label facing up.
Press [PLAY B] to start playback.
3
4
Press [STOP C] to stop playback.
DVD menu
DVDVD
2
1
3
4
STANDBY-ON
SPEED AUDIO
123
456
789
+10
0
DISPLAY VCR DVD PAUSE
PLAY
STOP
OPEN/CLOSE
/EJECT
Some discs contain menus which allow you to customize
DVD playback. Use [K / L / s / B] to select an item, then
press [ENTER] (or [PLAY B]).
Calling Up a Menu Screen during Playback
DVDVD
• Press [MENU] to call up the DVD menu.
• Press [TOP MENU] to call up the title menu.
Hint
• Menu operations may vary depending on the disc. Refer to the
manual accompanying the disc for more details.
Resume
DVDVD
Press [STOP C] during playback. Resume icon
will appear at the top-left on the TV screen.
Press [PLAY B], playback will resume from
the point at which playback was stopped.
R.STOP
Hint
•
To cancel resume, press [STOP C] one more time in the stop mode.
• The resume information will be kept even when unit is in standby
mode. For MP3, playback will resume from the beginning of the
track at which playback was stopped.
Paused and Step-by-Step Playback
DVDVD
Press [PAUSE F] during playback.
To continue playback, press [PLAY B].
DVDVD
PAUSE
The disc goes forward by one frame each time [PAUSE F]
is pressed in the pause mode.
To continue playback, press [PLAY B].
Hint
• Set “STILL MODE” to “FIELD” in the DISPLAY menu if pictures in
the pause mode are blurred. (Refer to pages 20-21.)
To use [PREV H / E], [NEXT D / G] on this unit
Press once to skip chapters or tracks to a desired point.
DVDVD
VIDEOAUDIO STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORDCHANNEL
Lights up when power is on.
IR
Hint
• When you play an MP3-format disc, details on page 16.
A “prohibited icon” may appear at the top-right on the TV
SKIP/CH.
VCR/TV
SLOW
•
screen when the operation is prohibited by the disc or this unit.
•
Some DVDs may start playback from title 2 or 3 due to specific programs.
• During the playback of a two-layered disc, pictures may
stop for a moment. This happens while the 1st layer is being
switched to the 2nd layer. This is not a malfunction.
TIP
:
You can change the On-Screen language in “PLAYER MENU”
setting. (Refer to page 20.)
Fast Forward / Reverse Search
DVDVD
Use [g] or [h] repeatedly during
playback to select the required
forward or reverse speed.
To use [PREV H / E], [NEXT D / G] on this unit
Pressing and holding
this unit will also change forward or reverse playback speed.
To continue playback, press [PLAY B].
[PREV H / E]
or
Hint
• Fast forward or reverse search speed is different depending on the
disc. Approximate speed is 1(x2), 2(x4), 3(x8), 4(x16) and 5(x32).
Slow Forward Search
DVDVD
Press [g] repeatedly in the pause mode to
select the required forward speed.
To use [NEXT D / G] on this unit
Pressing and holding [NEXT D / G] on this unit in the
pause mode will also change forward playback speed.
To continue playback, press [PLAY B].
Hint
• Slow forward speed is different depending on the disc.
Approximate speed is 1(1/32), 2(1/16), 3(1/8), 4(1/4) and 5(1/2).
• Set “STILL MODE” to “FIELD” in the DISPLAY menu if pictures in
the slow playback mode are blurred. (Refer to pages 20-21.)
• The reverse of slow playback is not available.
Zoom
DVDVD
1) Press [ZOOM] repeatedly during playback to select the
required zoom factor: x2, x3, x4, x1/2 or OFF.
x2x3x4x1/2
2)
Use [K / L / s / B] to slide the zoomed picture across the screen.
3)
To exit zoom function, press [ZOOM] repeatedly to select OFF.
Hint
•
Zooming function does not work while the disc menu is displayed.
•
Some part of the picture may not be zoomed depending on the disc status.
–
–
15
OPEN/
CLOSE
VCRDVD
DISC IN PLAYREC TIMER
PREVSOURCESTOP PLAY NEXT
2
E
1
[NEXT D / G]
1
341
on
DVD Functions
EN
MP3 Playback
ENTER
ENTER
ENTER
ENTER
ENTER
MP3 is a method of compressing files. You can copy MP3 files on CD-R/RWs from the
computer and play the files on this unit.
DVDVD
Insert an MP3-format disc, then the file list will automatically appear on the TV screen.
1
Select the desired folder from the list
on the left side in the file list.
004/027 001/013 00:00:36
file name1
3
1. file name1
1. folder1
3
2. file name2
2. folder2
3
3. file name3
3. folder3
3
4. file name4
4. folder4
3
5. file name5
5. folder5
3
6. file name6
6. folder6
3
7. file name7
7. folder7
3
8. file name8
8. folder8
Press [ENTER]
ENTER
ENTER
ENTER
or
PLAY
2 Select the desired file from the list on
the right side in the file list.
PLAY
001/027 001/007 00:00:12
1. folder1
2. folder2
3. folder3
4. folder4
5. folder5
6. folder6
7. folder7
8. folder8
OFF
ENTER
ENTER
ENTER
or
or [PLAY B] .
Search Functions
Using Track Search
Using [SEARCH MODE]
1
SEARCH
MODE
DVD Functions
DVDVD
--
/26 00:00:19
OFF
<Example : CD>
Using Title / Chapter Search
DVDVD
Using [SEARCH MODE]
SEARCH
1
MODE
or
--
/24001/002 00:00:30
file name11
3
1. file name11
3
2. file name12
3
3. file name13
3
4. file name14
3
5. file name15
3
6. file name16
3
7. file name17
Hint
• Some selections may take a while to
be recognized.
• Folders are known as Groups; files are
known as Tracks.
• MP3 files are accompanied by 3 icon.
• Folders are accompanied by
icon.
• Refer to “On-Screen Display” on
page 17 for more details.
• If you record data over 20 times, it may
OFF
not be played back correctly.
This player recommends the files recorded
under the following circumstances:
• Sampling frequency: 44.1kHz or 48kHz.
• Constant bit rate: 32kbps ~ 320kbps.
3 Refer to “Resume” on page 15.
STOP
Using Time Search
DVDVD
1
PLAY
OFF
SEARCH
MODE
03/24001/002--:--:
--
<Example : DVD>
OFF
2
123
456
789
0
3 Press [ENTER].
+10
--
/26 00:00:19
within 5 seconds
ENTER
ENTER
OFF
• To play a double-digit track, press the
track number directly for CDs (e.g. for
track 3, press [3] and [ENTER]).
• To play a triple-digit track, press the
track number directly for MP3. (e.g.
for track 3, press [3] and [ENTER]).
for track 26, press [2], [6] and [ENTER]).
Using [SKIP/CH. G//K, H/ L]
1
SKIP/CH.
PLAY
SKIP/CH.
Current Track
TR 1 TR 2 TR 3 TR 4
SKIP
SKIP
Hint
• On CDs, Track Search is not available for
Programmed or Random Playback.
ENTER
Press [SEARCH MODE] once for
the title search.
For the chapter search, press
cursor [B] to highlight
2
123
456
789
0
03/24
+10
within 5 seconds
3 Press [ENTER].
---
/002 00:00:32
ENTER
ENTER
.
OFF
Using [SKIP/CH. G//K, H/ L]
1
PLAY
SKIP/CH.
SKIP/CH.
Current Chapter
CH 1 CH 2 CH 3 CH 4
SKIP
SKIP
Hint
• Depending on the disc being played, this
function can also be performed by directly
entering the desired chapter number
with the number buttons. Refer to the
manual accompanying the disc.
• On DVDs, Title/Chapter Search is not
available for Programmed or Random
Playback.
–
–
16
Press cursor [B]
to highlight .
ENTER
CD: onceDVD: twice
2
123
456
789
0
03/24001/002--:--:
--
<Example : DVD>
OFF
within 5 seconds
ENTER
3 Press [ENTER].
ENTER
Hint
• To play time 0:15:00, press [1], [5], [0], [0]
of the number buttons.
• Press [CLEAR/C.RESET] to erase the
incorrect input at step 2.
• On DVDs/CDs, Time Search is not
available for Programmed or Random
Playback.
EN
On-Screen Display
3
3
3
e3
You can check the information about the current disc by pressing [DISPLAY] on the remote control.
1
DISPLAY
DVDVD
03/24001/002 00:00:40
T(Title):
Current title number / Total titles
Elapsed time of the current title
OFF
Current repeat setting
C(Chapter):
Current chapter number / Total chapters
1
DISPLAY
DVDVD
01/26 00:00:11
OFF
TR(Track):
Current track number / Total tracks
Current repeat setting
Elapsed time of the current track
CH(Chapter):
Current chapter number / Total chapters
Remaining time of the current
2
001/002 00:00:19 - 00:01:11
NORMAL
chapter
Current play mode setting
DISPLAY
Elapsed time of the current chapter
TT(Title):
Current title number / Total titles
Remaining time of the current title
3
03/24 00:00:20 - 00:01:09
NORMAL
Current play mode setting
DISPLAY
Elapsed time of the current title
4
Hint
•
Some DVD discs will not allow you to set chapter playback correctly.
2
DISPLAY
3
DISPLAY
4
1
DISPLAY
01/26 00:00:12 - 00:03:20
01/26 00:00:14 - 01:11:28
DVDVD
004/027 001/013 00:00:36
file name1
3
1. folder1
1. file name1
3
2. folder2
2. file name2
3
TR(Track):
Current track number / Total tracks
Remaining time of the current track
NORMAL
Current play mode setting
Elapsed time of the current track
ALL:
Current track number / Total tracks
Remaining time of the entire disc
NORMAL
Current play mode setting
Elapsed time of entire disc
Current group number / Total groups
Current track number / Total tracks
in the current group
Elapsed time of the current track
Current repeat setting
OFF
DVD Functions
TR(Track):
Current track number / Total tracks
in the current group
Elapsed time of the current track
Remaining time of the current track
Current play mode setting
001/013 00:00:43 - 00:03:36
2
DISPLAY
3
–
–
17
1. folder1
2. folder2. folder
1. folder1
2. folder2
3. folder3
file name1
3
3
3
file name1
3
3
3
1. file name1
2. file name2
. file nam
1. file name1
2. file name2
3. file name3
NORMAL
EN
Repeat / Random / Programmed Playback
ENTER
ENTER
ENTER
Repeat Playback
Repeat function is available only during
playback.
1
PLAY
REPEAT
Each time you press [REPEAT], repeat
function changes as example below.
OFF
CHAPTER
TITLE
OFF
TRACK
DVD Functions
ALL
OFF
TRACK
GROUP
ALL
CHAPTER
<Example : DVD>
(repeat off)
(current chapter repeat)
(current title repeat)
(repeat off)
(current track repeat)
(entire disc repeat)
(repeat off)
(current track repeat)
(current group repeat)
(entire disc repeat)
Hint
• Repeat setting (except “ALL”) will be
cleared when moving to another title,
chapter, track or group.
• Repeat playback may not function with
some discs or during repeat A-B playback.
Repeat A-B Playback
DVDVD
DVDVD
1
PLAY
A-
A-B
Programmed Playback
DVDVD
You may determine the order in which
chapters or tracks will play.
1 Press [MODE] once during stop
mode.
MODE
NORMAL RANDOM PROGRAM
at your desired starting point (A)
2
A-B
A-B
at your desired ending point (B)
• Point B should be in the same title
or track as point A.
• During playback, press [MODE].
CD/MP3: twice
DVD: three times
2 Select “PROGRAM”.
Then press [ENTER].
ENTER
ENTER
ENTER
Hint
• To exit the sequence, press [A-B] so that
OFF appears.
To cancel Point A, press [CLEAR/C.RESET]
•
at step 1.
• This function does not work in the other
repeat modes.
Random Playback
DVDVD
This function shuffles the playing
order of chapters or tracks instead
of playback in the sequence.
1
Press [MODE] once during stop
mode.
MODE
• During playback, press [MODE].
CD/MP3: twice
DVD: three times
NORMAL RANDOM PROGRAM
2 Select “RANDOM”.
Then press [ENTER].
ENTER
ENTER
ENTER
The RANDOM playback will start.
Hint
• During random playback, you cannot go
back to the previous track, using
[SKIP/CH. G/K] allows you to search
chapters or tracks randomly.
• During DVD Random Playback, you can
play chapters in the current title randomly.
• Some DVD discs will not allow you to
set random playback.
123
456
789
0
Total: 3 TITLE CHAPTER PLAY
02
05
01
--
+10
--
007
--
005
--
002
--
---
--
---
--
<Example : DVD>
• Up to 20 chapters or tracks can be
ordered.
• Enter the desired number with the number buttons.
DVD: title and chapter number
CD: track number
MP3: folder and track number
3 Select “PLAY”,
then press [ENTER].
ENTER
ENTER
Hint
• To erase all program at once, select
“ALL CLEAR’’ and press [ENTER] or
press [CLEAR/C.RESET] at step 2.
• If the title, chapter, track number is
incorrect, the programmed number you
entered will be skipped during
programmed playback.
• While a program is being played back,
[STOP C] works as follows;
Press [STOP C] and [PLAY B] next, so
that the programmed playback restarts.
Press [STOP C] twice and [PLAY B]
next, so that playback restarts from the
first track in the original order.
However, your programmed playback can
be restarted when you follow the above
steps. (Your programs are still stored until
either the disc is removed or power is
turned off.)
• Some DVD discs will not allow you to
set programmed playback.
• During program playback, you cannot
setup “
(MP3).
TITLE’’ (DVD), “ GROUP’’
MAX: 2DVD-PROGRAM
ALL CLEAR
--
--
---
---
---
--
--
---
---
---
--
--
---
---
---
--
--
---
---
---
--
--
---
---
---
–
18
–
EN
Special Settings
Subtitle Language
DVDVD
This unit allows you to select a subtitle
language (if available) during DVD
playback.
1
PLAY
SUBTITLE
T-S E T
Each time you press [SUBTITLE],
subtitle language changes as example
below.
OFF
ENG
FRE
...
1. ENG/6
(no subtitles)
(English subtitles)
(French subtitles)
To set subtitle ON/OFF
1
PLAY
SUBTITLE
T-S E T
1. ENG/6
2
ENTER
OFF
Each time you press [AUDIO] or
[s / B], audio language changes as
example below.
ENG
(English audio)
SPA
(Spanish audio)
FRE
(French audio)
...
Hint
•
Some discs will only allow you to change the
audio setting from the disc menu. Refer to the
manual accompanying the discs for details.
•
If your language is not shown after pressing
[AUDIO] several times, the disc may not have
that language. However, some disc allow
audio language setting on the disc menu.
(Operation varies depending on the disc, so
refer to the manual along with the disc.)
Camera Angles
DVDVD
Some DVD discs may
contain scenes which have
been shot simultaneously
from various angles. You can
change the camera angle if the
icon appears on the screen. If
the “ANGLE ICON” setting is “OFF” in
the OTHERS menu, the icon will
not appear. (Refer to pages 20-22.)
1
PLAY
1/8
ANGLE
Stereo Sound Mode
DVDVD
This unit allows you to select a sound
mode during CD playback.
1
PLAY
STEREO
AUDI O
Each time you press [
AUDIO]
or
[s / B], sound mode changes as
example below.
STEREO
L-ch
(right and left channels
are active)
(left channel is active)
R-ch
(right channel is active)
Virtual Surround
DVDVD
You can enjoy stereophonic virtual world
on your existing 2 channel stereo system.
1
PLAY
MODE
Press twice.
(once for CD and MP3)
OFF
Hint
• If your language is not shown after press-
ing [SUBTITLE/T-SET] several times, the
disc may not have that language. However, some discs allow subtitle language
setting on the disc menu. (Operation
varies depending on the disc, so refer to
the manual along with the disc.)
When “ ” appears on the TV screen, it
•
means no subtitle is recorded on the scene.
•
Some discs will only allow you to change
the subtitle from the disc menu. Refer to the
manual accompanying the discs for details.
Audio Language
DVDVD
This unit allows you to select an audio
language (if multiple languages are available on disc) during DVD playback.
1
PLAY
1. ENG Dolby D 5.1ch 48k/3
AUDI O
Each time you press [ANGLE] or
[s / B], camera angle changes.
Black Level Setting
DVDVD
Adjust the Black Level Setting to make
the dark areas of the TV picture brighter.
1
PLAY
ON
MODE
2
ENTER
ON: Makes the dark areas brighter.
OFF: Shows the original picture as recorded.
3
OFF
RETURN
–
19
–
2 Using [s / B], you can select the
desired sound mode.
ENTER
3D: Sound mode suitable for setting
stereophonic audio.
JAZZ: Sound mode suitable for Jazz music
Sound mode suitable for Rock music
ROCK:
POP: Sound mode suitable for Pop music
CLASSIC: Sound mode suitable for
OFF: No effects (original sound)
3
ROCK
Classic music
RETURN
Hint
• Virtual Surround is available only when the
DVD player is connected to a TV or stereo
using the red and white AUDIO OUT jacks
on the DVD player. Also, select [SETUP]
menu to use Dolby digital connection
(COAXIAL), and setting in PCM mode.
EN
DVD Functions
ENTER
ENTER
ENTER
DVDVD
ENTER
DVD Setup
You can change the settings of the unit.
1 Press [SETUP].
2 Select the desired item.
SETUP
ENTER
ENTER
<SETUP MENU>
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE menu
LANGUAGE_AUDIO
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
page 20
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
OTHERS
A
DISPLAY menu
DISPLAY_TV ASPECT
TV ASPECT
STILL MODE
page 21
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
B
AUDIO menu
AUDIO_DRC
DRC
DOWN SAMPLING
DOLBY DIGITAL
page 21
DVD Functions
LANGUAGE Setting
A
Follow steps 1 to 2 above.
3 Select the desired item.5 To exit the menu4 Select the desired language.
ENTER
LANGUAGE menu
LANGUAGE_AUDIO
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
OTHERS
ENTER
ENTER
AUDIO: ∗1 ∗2
(Default: ORIGINAL)
Sets the audio language.
SUBTITLE: ∗1 ∗2
(Default: OFF)
Sets the subtitle
language.
DISC MENU: ∗1
(Default: ENGLISH)
Sets the language in
DVD menu.
PLAYER MENU
(Default: ENGLISH)
Sets the language for the
On-Screen Display.
ENTER
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ON
OFF
PARENTAL menu
PARENTAL_PASSWORD
PASSWORDNO
C
ENTER
LANGUAGE_AUDIO
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE_SUBTITLE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE_DISC MENU
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
LANGUAGE_PLAYER MENU
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ENTER
ENTER
page 22
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
OTHERS
OFF
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
OTHERS
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
DUTCH
OTHERS
ENGLISH
FRANÇAIS
ESPAÑOL
OTHERS menu
OTHERS_ANGLE ICON
ANGLE ICON
YES
D
AUTO POWER OFFONOFF
page 22
ENTER
ENTER
E
INITIALIZE menu
INITIALIZE_INITIALIZE
INITIALIZEYES
page 23
F
SETUP
Hint
∗1
• Language options are not available
with some discs.
• If OTHER is selected in the AUDIO,
SUBTITLE or DISC MENU screen,
Select the desired language using
[K / L / s / B]. Press [ENTER].
LANGUAGE_AUDIO
DUTCH
RUSSIAN
KOREAN
NORWEGIAN
TURKISH
PORTUGUESE
HUNGARIAN
CHINESE
DANISH
ICELANDIC
GREEK
POLISH
JAPANESE
FINNISH
ROMANIAN
IRISH
CZECH
• Only the languages supported by the
disc can be selected.
∗2
• Language setting for Audio and
Subtitle are not available with some
discs. Then press [AUDIO] and
[SUBTITLE/T-SET]. Details are on
page 19.
–
20
–
EN
DISPLAY Setting
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
B
You can change the display functions. Follow steps 1 to 2 on page 20.
3 Select the desired item.
4
TV ASPECT: (Default: 4:3 LETTER BOX)
ENTER
DISPLAY menu
DISPLAY_TV ASPECT
TV ASPECT
STILL MODE
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
See Hint on the left.
DISPLAY_TV ASPECT
TV ASPECT
STILL MODE
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
ENTER
ENTER
4:3 LETTER BOX
4:3 PAN & SCAN
16:9 WIDE
STILL MODE:(Default: AUTO)
See Hint on the right.
DISPLAY_STILL MODE
Hint
TV ASPECT:
•
Select “4:3 LETTER BOX”, so
that black bars may appear on
the top and bottom of the screen.
• Select “4:3 PAN & SCAN” for
a full height picture with both
sides adjusted.
Select “16:9 WIDE” if a wide
•
screen TV is connected to this unit.
TV ASPECT
STILL MODE
AUTO
FIELD
FRAME
ENTER
ENTER
AUTO
FIELD
FRAME
Select the
desired
setting.
ENTER
Select the
desired
setting.
ENTER
ENTER
ENTER
ENTER
ENTER
5
To exit the menu
SETUP
Hint
STILL MODE:
• Select “AUTO” usually.
If you select “AUTO”,
•
automatically select the
best resolution setting
(FRAME or FIELD) based
on the data characteristics
of the pictures. (default).
• If you select “FIELD”,
the picture in the still
mode will be stabilized.
If you select “FRAME”, the
•
picture in the still mode
will be highly defined.
• An individual picture
on the TV screen is
called a “frame”, which
consists of two separate
images called a “field”.
• Some pictures may be
blurred if you select
“AUTO” in the still
mode due to their data
characteristics.
AUDIO Setting
C
Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow steps 1 to 2
on page 20.
3 Select the desired item.
ENTER
AUDIO menu
AUDIO_DRC
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
OFF
4
DRC (Dynamic Range Control): (Default: ON)
Set to “ON” to compress the range between soft and loud sounds.
AUDIO_DRC
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
OFF
ENTER
ENTER
ON
OFF
DOWN SAMPLING: (Default: ON)
Set to “ON” when outputting in 48kHz.
Set to “OFF” when outputting the original sound.
AUDIO_DOWN SAMPLING
DRC
DOWN SAMPLING
DOLBY DIGITAL
ON
OFF
ENTER
ENTER
ON
OFF
Select the
desired
setting.
ENTER
Select the
desired
setting.
ENTER
ENTER
ENTER
ENTER
ENTER
5 To exit the menu
SETUP
Hint
DRC:
• This function is
available only on
the discs which are
recorded in the Dolby
Digital format.
DOWN SAMPLING:
• When playing disc with
copyright protection,
the sound will be down
sampled at 48kHz, even
if you set to “OFF”.
DOLBY DIGITAL: (Default: BITSTREAM)
Set to “BITSTREAM” when the unit is connected to a Dolby Digital decoder.
• BITSTREAM: Outputs a Dolby Digital Signals.
• PCM: Convert the Dolby Digital into PCM (2 channel).
AUDIO_DOLBY DIGITAL
DRC
DOWN SAMPLING
DOLBY DIGITAL
BITSTREAM
PCM
ENTER
ENTER
BITSTREAM
PCM
Select the
desired
setting.
ENTER
ENTER
ENTER
DVD Functions
–
21
–
EN
PARENTAL Setting
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
ENTER
D
Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not be acceptable.)
This feature prevents your children from viewing inappropriate materials.
Parental Levels
Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set.
Follow steps 1 to 2 on page 20.
3 Press [ENTER],
and then select “YES”.
ENTER
PARENTAL menu
If the password has not
been set yet.
4 Enter your desired
ENTER
ENTERENTER
four digit password.
123
456
789
0
PASSWORDNO
Enter password
YES
ENTERENTER
----
5 Select “LEVEL”.
ENTER
PASSWORD
LEVEL
CHANGE
6 Select the desired
ENTER
level, and press
[ENTER].
PASSWORD
LEVEL
CHANGE
ENTER
8 [ADULT]
PARENTAL_PASSWORD
PASSWORDNO
YES
If the password has been
set already, enter the current four-digit password.
Enter a new
password again.
PASSWORDNO
Re-enter password
YES
----
TIPS FOR LEVELS
• 8 [ADULT]: DVD software of any grades (adult/general/
• 7 [NC-17]: No one under 17 admitted
• 6 [R]: Restricted; under 17 requires accompanying
• 5 [PGR]: Parental Guidance Recommended
• 4 [PG13]: Unsuitable for children under 13
PARENTAL_CHANGE
PASSWORD
LEVEL
CHANGE
Enter password
----
• 3 [PG]: Parental Guidance suggested
• 2 [G]: General Audience
• 1 [KID SAFE]: Suitable for children
If you do not need
parental lock, choose
DVD Functions
“NO”. Press [ENTER].
To Change the Password for Parental Controls
You can change your password for parental controls. Follow steps 1 to 2 on page 20.
ENTER
ENTER
6 Select “CHANGE” at
step 5 above.
PARENTAL menu
PARENTAL_CHANGE
PASSWORD
LEVEL
CHANGE
7 Enter your desired
four digit password.
123
456
789
0
PASSWORD
LEVEL
CHANGE
Enter new password
----
children) can be played back.
parent or adult guardian
8
Enter your new fourdigit password again.
123
456
789
0
PASSWORD
LEVEL
CHANGE
Re-enter password
7 To exit the menu
SETUP
ENTER
ENTER
9 To exit the menu
SETUP
Hint
• Record the password in case
you forget it.
If you forget the password, press
•
----
[4], [7], [3], [7] at step 3 above,
then enter your new password.
Password will be cleared and
parental levels will be set to “ALL”.
OTHERS Setting
E
You can change the other functions. Follow steps 1 to 2 on page 20.
43 Select the desired item.
(Default: ON)
ENTER
ENTER
(Default: ON)
ENTER
ENTER
–
ON
OFF
ON
OFF
22
ENTER
OTHERS menu
OTHERS_ANGLE ICON
ANGLE ICON
AUTO POWER OFFONOFF
ANGLE ICON:
Set to “ON” to show the angle icon
when multiple camera angles are
available during DVD playback.
ANGLE ICON
AUTO POWER OFFONOFF
AUTO POWER OFF:
Set to “ON” to turn this unit off
automatically after 30 minutes of no use.
ANGLE ICON
AUTO POWER OFFONOFF
5 To exit the menu
Select the
desired
setting.
ENTER
Select the
desired
setting.
ENTER
ENTER
ENTER
ENTER
ENTER
–
SETUP
EN
S
ENTER
Reset to the Default Setting (Except for PARENTAL Setting)
F
3
1 Press [SETUP].
STOP
<SETUP MENU>
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
PLAYER MENU
ETUP
2 Select “INITIALIZE”.
ENTER
INITIALIZE_INITIALIZE
INITIALIZEYES
ENTER
ENTER
Press
twice.
Select the desired PLAYER
MENU Language, using
the number buttons.
SELECT MENU LANGUAGE
ENGLISH
1
FRENCH
2
SPANISH
3
Hint
• When you cancel to
initialize at step 2.
Press [SETUP] to
exit the menu.
Information
Troubleshooting Guide
If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.
PROBLEMCORRECTIVE ACTION
No power.
DVD / VCR
This unit does not
respond to the remote
control.
Poor picture or noise.
Timer recording is impossible.
Cannot go into record
mode.
Playback picture is partially
noisy.
Cannot view a tape but
VCR
the audio is OK.
No or poor, playback
picture.
TV programs cannot be
seen normally.
Video or color fades in
and out when making a
copy of a video tape.
Cannot remove the tape.
No picture.
Disc cannot be played.
No sound.
DVD
No DTS audio is output
Distorted picture.
Audio or subtitle language
does not match the setup.
The camera angle cannot
be changed.
Audio or subtitle language
cannot be changed.
“Prohibited icon” appears
on the screen, prohibiting
an operation.
•
Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
• Some functions are prohibited on some discs.
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control.
• You have to be within 23 feet (7m) of this unit.
• Check if the right mode is selected. If it’s not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control.
• Check if a cassette tape is in this unit.
• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio
in response to your pressing buttons on the remote control, the remote control is working.
• Press and hold any button on remote control toward a digital camera. The remote control is working if you confi rm infrared light through the
digital camera.
• Interference signal may be received. Change the position and orientation of the unit.
• Make sure the Timer Recording is set correctly.
• Make sure TIMER indicator on the front panel lights up. If not, press [SUBTITLE/T-SET].
• Make sure the VCR clock is set correctly.
• Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.
• Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR SOURCE light is lit.
• Adjust tracking control for a better picture by pressing [CHANNEL L/K]] on the unit or [SKIP/CH. G/K, H/L] on the remote control.
• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING”.
• Make sure the VCR is not in the Menu mode.
• Change the RF output channel to CH4. Then select the same channel on the TV.
• Fine tune your TV.
• Re-check the ANT-IN and ANT-OUT connections. See the front page and page 6.
• Press [VCR].
•
Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR SOURCE light is lit, then set it to the TV position by pressing [VCR].
• You cannot copy a copyrighted video tape. You are experiencing copy guard protection.
• Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode.
• Connect the video cable fi rmly.
• Insert a correct video disc that plays on this unit.
• Press [DVD] on the remote control. Check if the DVD SOURCE light is lit. Then try other DVD features.
• Insert the disc.
• Clean the disc.
• Place the disc correctly with the label side up.
• Cancel the parental lock or change the control levels.
• Handle a disc with special care so that it does not have fi ngerprints, scratches, or dusts on its surface.
• Connect the audio cables fi rmly.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This unit does not support DTS audio.
-This is not a malfunction.
• Connect this unit directly to the TV.
• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
• The selected language is not available for audio or subtitles on the DVD.
-This is not a malfunction.
• The DVD does not contain sequences recorded from different camera angles.
-This is not a malfunction.
• The DVD does not contain audio source or subtitles in the selected language.
-This is not a malfunction.
• That operation is prohibited by this unit or the disc.
-This is not a malfunction.
–
–
23
Information
EN
Specifications
Video Heads :
Four Heads
Output signal format :
NTSC color
Power source :
120 V AC +/- 10%, 60 Hz +/- 0.5%
Power consumption :
21 W (standby: 3.8W)
LIMITED WARRANTY
FUNAI CORP. will repair this product, free of charge in the USA in the event
of defect in materials or workmanship as follows:
DURATION:
PARTS: FUNAI CORP. will provide parts to replace defective parts without
LABOR: FUNAI CORP. will provide the labor without charge for a period of
LIMITS AND EXCLUSIONS:
This warranty is extended only to the original retail purchaser. A purchase
receipt or other proof of original retail purchase will be required together with
the product to obtain service under this warranty.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are
altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. This limited warranty does not apply to any product
not purchased and used in the United States.
This product is produced for home use and this warranty only covers failures
due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused
by repairs, alterations or product not supplied by FUNAI CORP., or damage
which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel,
rental or office use of this product or damage which results from fire, flood,
lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL), ANY COSMETIC PARTS,
COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO
EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL
DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE OF OR THE
INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU
charge for one (1) year from the date of original retail purchase.
Certain parts are excluded from this warranty.
ninety (90) days from the date of original retail purchase.
Information
Operating temperature :
41°F (5°C) to 104°F (40°C)
Dimensions :
W : 17 1/8” (435mm)
H : 3 11/16” (94mm)
D : 9 3/16” (233mm)
Weight :
Approx 6.0lbs (2.7kg)
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL
OTHER LIABILITIES ON THE PART OF FUNAI, ALL OTHER WARRANTIES
INCLUDING THE WARRANTY OF MERCHANTABILITY, AND FITNESS
FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY
FUNAI AND ITS REPRESENTATIVES IN THE UNITED STATES. ALL
WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY
AN AUTHORIZED SERVICE CENTER. THIS WARRANTY IS VALID WHEN
THE UNIT IS CARRIED-IN TO AN AUTHORIZED SERVICE CENTER.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU
MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. IF,
AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE UNABLE TO
OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE
CONTACT FUNAI CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF
THIS PRODUCT WITHOUT PRIOR NOTICE.
WARRANTY STATEMENT REGARDING NON AUTHORIZED REPAIRS:
To obtain warranty service, you must take the product, or deliver the product
freight prepaid, in either its original packaging or packaging affording an equal
degree of protection, to any AUTHORIZED SERVICE CENTER. FUNAI
CORP. will not reimburse you for any service done by unauthorized service
providers without prior written approval.
To locate your nearest AUTHORIZED SERVICE CENTER or for general
service inquiries, please contact us at:
• Designs and specifications are subject
to change without notice.
• If there is a discrepancy between
languages, the default language will be
English.
FUNAI CORPORATION
Customer Service
Tel :1-800-518-1180
http://www.funai-corp.com
19900 Van Ness Avenue, Torrance, CA 90501
–
24
–
EN
Español
O
VCRDVD
SOURCE
VCR
VCR
Conexiones
1
Consulte la “Basic TV Connection” en la página delantera
antes de utilizar esta unidad.
Canal de salida RF
Si el canal 3 se está utilizando para una transmisión,
1) Programe su televisor al canal 4.
2) Inserte una cinta pregrabada en esta unidad.
3) Pulse [SOURCE] en la unidad para que se encienda la
luz VCR SOURCE.
• Si aparece ruido en la pantalla de TV, presione [VCR/TV]
en el control remoto.
4) Pulse una vez [PLAY B].
5) Después de unos segundos, pulse [PLAY B] en la
unidad durante 3 segundos.
• El canal de salida RF cambiará del canal 3 al canal 4 y
podrá ver una imagen reproducida.
• Cuando no aparezca una imagen en la pantalla del
televisor, repita el paso 4.
6) Pulse [STOP C] para parar la reproducción.
Instalación de las pilas del control
2
remoto
1
Conmutación VCR/DVD
3
NREWF.FWDSTOP/EJECTPLAYRECORDCHANNEL
✄
IR
OPEN/
CLOSE
VCR DVD
2
DISC IN PLAYRECTIMER
PREVSOURCE STOP PLAY NEXT
Botón VCR
Botón DVD
Botón SOURCE
Luz DVD SOURCE
Luz VCR SOURCE
3
STANDBY-ON
SPEED AUDIO
123
456
789
0
+10
DISPLAY VCR DVD PAUSE
PLAY
STOP
RECORD
MENU
ENTER
SETUP TOP MENU
SEARCH
MODE ZOOM
MODE
SUBTITLE
ANGLE
REPEAT A-B
T-SET
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
RETURN
C. RESET
SLOW
CLEAR/
Pulse [B] para AJUSTE AUTO.
3
CA 01
AJUSTE AUTO
Conecta el cable de la caja de canales de cable o la caja de
satélite en la toma ANT-IN de la unidad?
Si Pulse
[MENU]
SI
para salir.
NO
No Espere unos minutos.
Después del escaneo
• El sintonizador se detiene en el canal memorizado más bajo.
• Puede seleccionar sólo los canales memorizados en esta unidad
con [SKIP/CH. G//K, H//L] (o [CHANNEL K // L]).
• Si aparece nuevamente “AJUSTE AUTO” en la pantalla de TV,
verifique las conexiones de cable. Presione nuevamente [B].
Ajuste del reloj
5
1
2
3
4
VCR
MENU
• Si no se ha ajustado el reloj, aparece
la pantalla AJUSTE DE RELOJ
cuando pulse [MENU]. En este caso,
vaya al paso 2.
Seleccione el mes actual.
Seleccione el dia actual.
Seleccione el año actual.
o
o
o
o
- M E N U -
PROGRAMAR
AUTOREPETIR [OFF]
AJUSTE CANAL
B AJUSTE DE RELOJ
SELEC. IDIOMA
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / – – – – – –
HORA MINUTO AM/PM
– – : – – – –
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / 0 2 – – – –
HORA MINUTO AM/PM
– – : – – – –
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / 0 2 2 0 0 6
HORA MINUTO AM/PM
– – : – – – –
Pulse [VCR] en el control remoto. (Compruebe que está
MODO VCR
encendida la luz VCR SOURCE.)
Pulse [DVD] en el control remoto. (Compruebe que está
MODO DVD
encendida la luz DVD SOURCE.)
Consejo
• Si pulsa sólo [SOURCE] en el panel frontal NO cambía el modo
del control remoto. DEBE seleccionar también el modo correcto en
el control remoto.
Activación de la unidad por primera vez
4
Encienda el televisor y sintonice al canal 3.
1
• Si el canal 3 se está utilizando para una
2
VCR
transmisión, vea la sección “Canal de salida RF”.
STANDBY-ON
o
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
–
25
Seleccione la hora actual.
5
o
Seleccione los minutos actuales.
6
o
Seleccione “AM” o “PM”.
7
o
Para salir de la pantalla AJUSTE DE RELOJ
8
–
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / 0 2 LUN 2 0 0 6
HORA MINUTO AM/PM
0 5 : – – – –
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / 0 2 LUN 2 0 0 6
HORA MINUTO AM/PM
0 5 : 4 0 – –
AJUSTE DE RELOJ
MES DIA AÑO
1 0 / 0 2 LUN 2 0 0 6
HORA MINUTO AM/PM
0 5 : 4 0 P M AM
BPM
Español
ES
Español
VCR
Reproducción de la
6
grabadora de vídeo
Antes: Encienda el televisor
y cambie al canal 3.
• Si el canal 3 se está utilizando
para una transmisión, vea la
sección “Canal de salida RF”.
VCR
1
Para parar la
3
reproducción
STOP
Reproducción de DVD/
7
CD
Antes: Encienda el televisor, amplificador
y otros equipos que puedan estar
conectados a esta unidad. Asegúrese
que el televisor y el sintoamplificador de
audio (de venta en los comercios) están
en el canal correcto.
DVDVD
1
STANDBY-ON
Para empezar
3
la reproducción
PLAY
Control remoto
8
Español
2
4
2
OPEN/CLOSE
/EJECT
Ponga un disco con la
etiqueta hacia arriba.
4
STANDBY-ON
SPEED AUDIO
123
456
789
0
DISPLAY VCR DVD PAUSE
PLAY
STOP
RECORD
MENU
ENTER
SETUP TOP MENU
SEARCH
MODE ZOOM
SUBTITLE
ANGLE
REPEAT A-B
T-SET
Para empezar la
reproducción
PLAY
Para expulsar
OPEN/CLOSE
/EJECT
Para parar la
reproducción
STOP
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
SLOW
+10
RETURN
CLEAR/
MODE
C. RESET
Disco/cinta
Botón
(Orden alfavético)
123
456
789
0
A-B
ANGLE
AUDIO
CLEAR/
C. RESET
DISPLAY
DVD
ENTER
MENU
MODE
OPEN/CLOSE
/EJECT
PAUSE
PLAY
RECORD
REPEAT
RETURN
SEARCH
MODE
SETUP
SKIP/CH.
SKIP/CH.
SLOW
SPEED
STANDBY-ON
STOP
SUBTITLE
T-SET
TOP MENU
VCR
VCR/TV
ZOOM
Modo DVD
• Para seleccionar directamente
el capítulo o el título.
+10
• Para buscar en avance/
retroceso en un disco.
•
Para empezar la reproducción en
avance lento durante el modo de pausa.
• Para repetir entre los puntos A
y B elegidos.
•
Para seleccionar los ángulos
de la cámara en un disco.
• Para seleccionar el idioma de
audio en un disco.
• Para eliminar el Nº de estado
en la entrada de programa.
• Para borrar los números
mal entrados.
• Para borrar el punto para la
repetición A-B.
• Para indicar el modo de disco
actual.
• Para seleccionar el modo de
salida de DVD.
• Para activar el mando a distancia en el modo DVD.
• Para mover el cursor y
determinar su posición.
• Para llamar el menu en un
disco.
• Para disponer el orden de
reproducción o la reproducción
aleatoria.
• Para activar/desactivar el nivel
del negro.
• Para activar/desactivar el
ambiental virtual.
• Para abrir o cerrar la bandeja
del disco.
• Para hacer una pausa de
reproducción del disco.
• Para avanzar la reproducción
un cuadro a la vez.
• Para empezar la reproducción
del disco.
•
Para reproducir repetidamente
un capítulo o título.
• Para volver a la operación
previa en el menú.
• Para buscar un capítulo, título
u hora.
• Para llamar el menú de
programación de DVD.
• Para saltar capítulos o titulo.
• Para encender o apagar la
unidad.
• Para parar la reproducción.• Para parar la reproducción.
• Para seleccionar subtítulos en
un disco.
• Para llamar el menú superior
en un disco.
• Para seleccionar la posición de
DVD o la posición del televisor.
•
Para ampliar la imagen de vídeo
en DVD. (x2 / x3 / x4 / x1/2)
–
–
26
• Para seleccionar directamente
la canción. (CD)
• Para seleccionar directamente
el grupo/canción. (MP3)
• Para buscar en avance/
retroceso en un disco.
• Para repetir entre los puntos A
y B elegidos.
•
Para seleccionar ESTÉREO,
L-ch o R-ch. (CD)
• Para eliminar el Nº de estado
en la entrada de programa.
• Para borrar los números
mal entrados.
• Para borrar el punto para la
repetición A-B.
• Para indicar el modo de disco
actual.
• Para seleccionar el modo de
salida de DVD.
• Para activar el mando a
distancia en el modo DVD.
• Para mover el cursor y
determinar su posición.
• Para disponer el orden de
reproducción o la reproducción
aleatoria.
• Para activar/desactivar el
envolvente virtual.
• Para abrir o cerrar la bandeja
del disco.
• Para hacer una pausa en la
reproducción del disco.
• Para empezar la reproducción
del disco.
• Para reproducir repetidamente
una canción o disco. (CD)
•
Para reproducir repetidamente
una canción, grupo o disco. (MP3)
• Para volver a la operación
previa en el menú.
• Para buscar una canción.
• Para buscar el tiempo. (CD)
• Para buscar los grupos. (MP3)
• Para llamar el menú de
programación de DVD.
• Para saltar canciones. (CD)
• Para saltar los grupos o
canciones. (MP3)
• Para encender o apagar la
unidad.
•
Para seleccionar la posición de
CD/MP3 o la posición del televisor.
Mode de grabadora de video
• Para seleccionar el canal.
• El botón +10 no tiene efecto
en el modo de grabadora de
vídeo.
• Para el avance/retroceso de
una cinta.
• Para salir del menú de la
grabadora de vídeo.
• Para reponer el contador de
cinta.
• Para indicar la hora actual,
contador de cinta y canal.
•
Para seleccionar un
ítem en el menú de la
grabadora de vídeo.
•
Para avanzar al
siguiente menú de la
grabadora de vídeo.
•
Para volver un paso
durante el ajuste del
• Para llamar el menú de la
•
•
• Para avanzar la reproducción
• Para empezar la reproducción
•
• Para llamar el menú de
• Para cambiar de canal.
•
• Para ver la cinta en cámara
• Para seleccionar la velocidad
• Para encender o apagar la
• Para parar la reproducción o
•
•
•
•
reloj y temporizador.
grabadora de vídeo.
Para expulsar el videocasete
de la grabadora de vídeo.
Para hacer una pausa de la reproducción
o grabación de la cinta.
un cuadro a la vez.
de la cinta.
Para empezar una grabaciòn o
una grabaciòn de un toque.
búsqueda de índice u hora.
Para ajustar manualmente elseguimiento
durante la reproducción.
lenta.
de grabación.
unidad.
grabación.
Para poner la grabadora de
vídeo en el modo de espera para
una grabación con temporizador.
Para seleccionar el modo de salida
de la grabadora de vídeo.
Para activar el mando a distancia en
el modo de la grabadora de vídeo.
Para seleccionar la posición de la grabadora
de vídeo o posición del televisor.
✄
ES
Quick Use Guide
VCRDVD
SOURCE
VCR
VCR
Connections
1
Please refer to “Basic TV Connection” on the front page
before you use this unit.
RF Output Channel
If channel 3 has been already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press [SOURCE] on the unit so that the VCR SOURCE
light is lit.
•
If noise appears on the TV screen, press [VCR/TV] on the
remote control.
4) Press [PLAY B] once.
5) After a few seconds, press and hold [PLAY B] on the
unit for 3 seconds.
• The RF output channel will change to channel 4 from
channel 3 and you will see a playback picture.
• When a picture does not appear on the TV screen,
repeat step 4.
6) Press [STOP C] to stop playback.
Installing the Batteries for the Remote
2
Control
1
VCR/DVD Switching
3
STANDBY-ONREWF.FWDSTOP/EJECTPLAYRECORDCHANNEL
✄
Press [VCR] on the remote control. (Verify that the VCR SOURCE
IR
2
OPEN/
CLOSE
VCR DVD
DISC IN PLAYRECTIMER
PREVSOURCE STOP PLAY NEXT
SOURCE button
DVD SOURCE light
VCR SOURCE light
VCR MODE
VCR button
DVD button
3
STANDBY-ON
SPEED AUDIO
123
456
789
0
+10
DISPLAY VCR DVD PAUSE
PLAY
STOP
RECORD
ENTER
MENU
SETUP TOP MENU
SEARCH
MODE ZOOM
MODE
SUBTITLE
ANGLE
REPEAT A-B
T-SET
OPEN/CLOSE
/EJECT
SKIP/CH.
RETURN
VCR/TV
SLOW
CLEAR/
C. RESET
light is lit.)
Press [DVD] on the remote control. (Verify that the DVD SOURCE
DVD MODE
light is lit.)
Hint
• Pressing only [SOURCE] on the front panel DOES NOT switch the
mode of the remote control. You MUST select the correct mode on
the remote control.
Press [B] to start Auto Set Up.
3
CH 01
AUTO SET UP
Do you connect the cable from the cable box or the satellite box to
the unit’s ANT-IN jack?
Yes
Press [MENU] to exit.
No
Please wait for a few minutes.
YES
NO
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).
• If “AUTO SET UP” appears on the TV screen again, check the
cable connections. Then, press [B] once again.
Clock Set Up
5
VCR
Press [MENU] and select “CLOCK SET“.
1
Then press [B] to go to next step.
MENU
or
• If the clock is not set, the CLOCK SET screen appears when
you press [MENU]. In this case, go to step 2.
Select the current month.
2
Then press [B] to go to next step.
or
Select the current day.
3
Then press [B] to go to next step.
or
Select the current year.
4
Then press [B] to go to next step.
or
Select the current hour.
5
Then press [B] to go to next step.
or
Select the current minute.
6
Then press [B] to go to next step.
or
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 2 0 0 6
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
HOUR MINUTE AM/PM
0 5 : 4 0 – –
4
1
2
Turn on the Unit for the First Time
VCR
Turn on the TV and set it to channel 3.
• If channel 3 has been already occupied for
broadcasting, see “RF Output Channel” section.
Select your language when turning this unit on for the first time.
Then press [B] to go to next step.
STANDBY-ON
or
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
–
27
Select “AM” or “PM”.
7
To exit the CLOCK SET screen
8
–
CLOCK SET
MONTH DAY YEAR
1 0 / 0 2 MON 2 0 0 6
or
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
EN
Quick Use Guide
VCR
VCR Playback
6
Before: Turn on the TV and
set it to channel 3.
• If channel 3 has been already
occupied for broadcasting, see
“RF Output Channel” section.
VCR
Insert a video
1
cassette into this unit.
To stop
3
playback
STOP
DVD/CD Playback
7
Before: Turn on the TV, amplifier
and any other components which are
connected to this unit. Make sure the
TV and audio receiver (commercially
available) are set to the correct channel.
DVDVD
2
4
12
STANDBY-ON
3
8
Printed in China
OPEN/CLOSE
/EJECT
Insert a disc with
label facing up.
To start
playback
PLAY
4
Remote Control
STANDBY-ON
SPEED AUDIO
123
456
789
0
DISPLAY VCR DVD PAUSE
PLAY
STOP
RECORD
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE
ANGLE
T-SE T
To start
playback
PLAY
To eject the
cassette
OPEN/CLOSE
/EJECT
To stop
playback
STOP
OPEN/CLOSE
/EJECT
SKIP/CH.
VCR/TV
SLOW
+10
ENTER
RETURN
SEARCH
CLEAR/
MODE
C. RESET
REPEAT A-B
Button
(Alphabetical order)
Disc/Tape
123
456
789
0
A-B
ANGLE
AUDIO
CLEAR/
C. RESET
DISPLAY
DVD
ENTER
MENU
MODE
OPEN/CLOSE
/EJECT
PAUSE
PLAY
RECORD
REPEAT
RETURN
SEARCH
MODE
SETUP
SKIP/CH.
SKIP/CH.
SLOW
SPEED
STANDBY-ON
STOP
SUBTITLE
T-SET
TOP MENU
VCR
VCR/TV
ZOOM
+10
DVD modeVCR mode
• To select chapter or title
directly.
•
To search forward/backward
through a disc.
•
To begin slow forward
playback in the pause mode.
• To repeat between your
chosen point of A and B.
• To select camera angles on
a disc.
• To select audio languages
on a disc.
• To remove status number in
program input.
• To clear the numbers
entered incorrectly.
• To cancel the point for A-B
repeat.
• To display the current disc
mode.
•
To select the DVD output mode.
• To activate the remote
control in DVD mode.
• To move the cursor and
determine its position.
•
To call up the Menu on a disc.
• To arrange the playing order
or play randomly.
• To set black level on/off.
• To set virtual surround
on/off.
• To open or close the disc
tray.
• To pause disc playback.
• To advance playback one
frame at a time.
• To select track directly. (CD)
• To select group/track
directly. (MP3)
• To search forward/backward
through a disc.
•
To repeat between your
chosen point of A and B.
• To select STEREO, L-ch or
R-ch. (CD)
• To remove status number in
program input.
• To clear the numbers
entered incorrectly.
• To cancel the point for A-B
repeat.
• To display the current disc
mode.
To select the DVD output mode.
•
• To activate the remote
control in DVD mode.
• To move the cursor and
determine its position.
• To arrange the playing order
or play randomly.
To set virtual surround on/off.
•
• To open or close the disc
tray.
• To pause disc playback.
• To select channel.
• The +10 button has no
effect in VCR mode.
• To forward/backward a tape.
• To exit the VCR Menu.
• To reset the tape counter.
• To display the current time,
tape counter, and channel.
•
To select an item
on the VCR Menu.
•
To advance to the
next VCR Menu.
•
To go back one
step during clock
and timer setting.
• To call up the VCR Menu.
• To eject the video
cassette from the VCR.
• To pause tape playback or
recording.
• To advance playback one
frame at a time.
• To begin disc playback.• To begin disc playback.• To begin tape playback.
• To start a recording or One
Touch Recording.
• To call up the index or time
search menu.
• To change channels.
• To adjust the tracking
manually during playback.
• To view the tape in slow
motion.
• To select the recording
speed.
• To play a chapter or title
repeatedly.
• To return to the previous
operation in menu.
• To search chapter, title or
time.
• To call up the DVD setup
menu.
• To skip chapters or titles.
• To play a track or disc
repeatedly. (CD)
• To play a track, group or
disc repeatedly. (MP3)
• To return to the previous
operation in menu.
• To search track.
• To search time. (CD)
• To search groups. (MP3)
• To call up the DVD setup
menu.
• To skip tracks. (CD)
• To skip groups or tracks.
(MP3)
• To turn the unit on/off.• To turn the unit on/off.• To turn the unit on/off.
• To stop playback.• To stop playback.
• To select subtitles on a disc.
• To call up the Top Menu on
a disc.
• To select DVD position or
TV position.
• To magnify part of a picture.
(x2 / x3 / x4 / x1/2)
• To select CD/MP3 position
or TV position.
• To stop playback or
recording.
To put the VCR into standby
•
mode for a Timer Recording.
• To select the VCR output mode.
• To activate the remote
control in VCR mode.
• To select VCR position or
TV position.
E8C1SUD
1VMN23177 ★★★★★
✄
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.