Funai SRT2119 User Manual

This TV can receive C1 and C2 of Caption and Text.

Caption Mode

(1)Characters can be displayed on the TV screen when the received broadcast signal contains

Caption Signals.

(2)Paint-on mode: Displays input characters on the screen immediately.

Pop-on mode: Once characters are stored in memory, they are displayed all at once.
Roll-up mode: Displays the characters continuously by scrolling (max. 4 lines)

Note: If the CAPTION C1 or C2 is selected but the caption signal is not included, characters will

not be displayed.

Text Mode

(1)Displays the text on the screen by scrolling (max. 7 lines)
(2)If the received broadcast signal does not contain caption or text signals, no change will occur.

Notes:

(1)When your TV receives a special effects playback signal (i.e., Search, Slow, Still) from a

VCR’s video output channel (CH3 or CH4), your TV may not display the correct caption or

text.
(2)Captions and texts may not match the TV voice exactly.
(3)Interference may cause the closed caption system not to function properly.
(4)The caption or text characters will not be displayed while the menu display or functions dis-

play is shown.
(5)If you see this screen :

If your TV displays a black box on the screen, this means that your TV is set to TEXT mode. To
clear screen, select CAPTION C1, C2 or CAPTION [OFF].

ANTENNA/CABLE CONNECTIONS

PRECAUTIONS

● Place your TV in a room with adequate ventilation.

● Keep your TV set away from sources of direct heat, such as heat registers or direct sunlight.

● Do not place your TV on soft surfaces, such as rugs or blankets.

● Leave enough room for air to circulate around the bottom, top and back of the set.

FEATURES

● Tinted, Bright Black Matrix Picture Tube

● 181 Channel Selection- All VHF/UHF channels plus up to 125 cable channels.

● PLL Frequency Synthesized Tuning- The latest PLL frequency synthesized electronic

tuning system provides free and easy channel selection, and lets you tune directly to any chan­nel using the channel number buttons (0~9 and +100-key) on the remote control.

● On-Screen Function Display.

● Full-Function Remote Control

● Sleep Timer

● Closed Caption Decoder- You may view specially labeled (cc) TV programs, movies, news,

prerecorded tapes, etc. with either a dialogue caption or text display added to the program.

● Auto Shut Off Function- If there is no air signal input from the antenna terminal and no

user operation for 15 minutes, the TV will turn itself off automatically.

● V-CHIP- Enables parents to prevent their children from watching inappropriate material on TV.

Date of Purchase
Dealer Purchase from
Dealer Address

Dealer Phone No.
Model No.
Serial No.

The serial number of this product may be found on the back of the TV. No others have the same
serial number as yours. You should record the number and other vital information here and retain
this book as a permanent record of your purchase to aid identification in case of theft.

ANT.IN

CLOSED CAPTION

UHF
Antenna
(Not supplied)

VHF
Antenna

(Not supplied)

VHF/UHF Combiner
(Not supplied)

VHF/UHF
Combination Antenna
(Not supplied)

UHF/VHF Rod
Antenna
(Supplied with

13” model only)

OR

OR

ANT. IN

OUT IN

75-ohm
Coaxial Cable

From Cable System

From Cable System
or Satellite Antenna
75-ohm
Coaxial Cable

CATV Box

*

or Satellite Box
(Not supplied)

*Some cable TV systems use scram-

bled signals and require a special con­verter to receive these channels.
Consult your local cable company.

Note to CATVsystem installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of
the NEC that provides guidelines for proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system of the building as close to the point
of cable entry as practical.

FCC WARNING- This equip­ment may generate or use radio
frequency energy. Changes or
modifications to this equipment
may cause harmful interference
unless the modifications are
expressly approved in the
instruction manual. The user
could lose the authority to oper­ate this equipment if an unau­thorized change or modification
is made.

IF YOU NEED ADDITIONALASSISTANCE FOR SET-UP OR OPERATING
AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE
1-800-968-3429.

Owner’s
Manual

0EMN01845 Printed in China

L1359UK * * * * *

This Owner’s Manual is made of recycled paper.

COLOR TELEVISION

SRT2113 (13 inch)
SRT2119 (19 inch)

Before plugging the UHF/VHF Rod
Antenna (Supplied with 13” model only)
into the ANT(enna). IN jack, check that the
pin is not bent. If it is bent, straighten the
pin as illustrated, then plug the pin into the
ANT(enna). IN jack.

Bent pin

Cable

Plug

(Needs to be straightened) (Straight pin)

SYLVANIA

LIMITED WARRANTY

SEARS will repair this SYLVANIA product, free of charge in the USA in the event of defect in
materials or workmanship as follows:

DURATION:

PARTS: SEARS will provide parts to replace defective parts without charge for one (1)

year from the date of original retail purchase. Two (2) years for Picture Tube. Certain
parts are excluded from this warranty.

LABOR: SEARS will provide the labor without charge for a period of ninety (90) days

from the date of original retail purchase.

LIMITS AND EXCLUSIONS:

This warranty is extended only to the original retail purchaser. A purchase receipt or other proof of origi­nal retail purchase will be required together with the product to obtain service under this warranty.

This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced,

missing or if service was attempted by an unauthorized service center. This SYLVANIA Limited warran­ty does not apply to any the product not purchased and used in the United States.

This warranty only covers failures due to defects in material or workmanship which occurs during nor­mal use. It does not cover damage which occurs in shipment, or failures which are caused by repairs,
alterations or product not supplied by SEARS or damage which results from accident, misuse,
abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use
such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or
other acts of God.

This warranty does not cover packing materials, any accessories (except remote control), any cosmetic
parts, complete assembly parts, demo or floor models. SEARS and its representatives or agents
shall in no event be liable for any general, indirect or consequential damages arising out of or occa­sioned by the use of or the inability to use this product. This warranty is made in lieu of all other war­ranties, express or implied, and of all other liabilities on the part of SEARS, all other warranties includ­ing the warranty of merchantability, and fitness for a particular purpose, are hereby disclaimed by
SEARS and its representatives in the united states. All warranty inspections and repairs must be per­formed by a SEARS authorized service center. Warranty is valid when the unit is taken to SEARS autho­rized service facility. The product must be accompanied by a copy of the original retail purchase receipt.
if no proof of purchase is attached, the warranty will not be honored and repairs costs will be charged.

IMPORTANT:

This limited warranty gives you specific legal rights, you may have other rights that vary from state to
state, if, at any time during the warranty period, you are unable to obtain satisfaction with the repair of
this product, please contact SEARS.

ATTENTION:

SEARS RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.

To locate your nearest SYLVANIA Authorized Service Center or general service procedure,
please call 1-800-469-4663 or visit:

www.sears.com

Customer Service Tel :[phone]

NOTE:You MUST PRESET channels BEFORE using CHANNEL ▲ or ▼ button.

L1359.QX33 01.5.14 5:51 PM Page 1

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI­ANCE TO RAIN OR MOISTURE.

IMPORTANT SAFEGUARDS

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK) NO
USER SERVICEABLE PARTS INSIDE. REFER SER­VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

THIS SYMBOL INDICATES THATDAN­GEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRE­SENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT
THERE ARE IMPORTANTOPERATING
AND MAINTENANCE INSTRUCTIONS
IN THE LITERATURE ACCOMPANYING
THE APPLIANCE.

The important note is located on the rear of the cabinet.

1. Read instructions-All the safety and operating instruc­tions should be read before the appliance is operated.

2. Retain Instructions-The safety and operating instruc­tions should be retained for future reference.

3. Heed Warnings-All warnings on the appliance and in
the operating instructions should be adhered to.

4. Follow Instructions-All operating and use instructions
should be followed.

5. Cleaning-Unplug TVfrom the wall outlet before clean­ing. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupt­ed service and, that for some specific reason, such as
the possibility of the loss of an authorization code for a
CATV converter, is not intended to be unplugged by
the user for cleaning or any other purpose, may
exclude the reference to unplugging the appliance in
the cleaning description otherwise required in item 5.

6. Attachments-Do not use attachments not recommended
by the TV manufacturer as they may cause hazards.

7. Water and Moisture-Do not use this TV near water, for
example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, or near a swimming
pool, and the like.

8. Accessories-Do not place this TVon an unstable cart,
stand, tripod, bracket, or table. The TV may fall, caus­ing serious injury to someone, and serious damage to
the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or
sold with the TV.
Any mounting of the appliance should follow the man­ufacturer’s instructions and should use a mounting
accessory recommended by the
manufacturer. An appliance and
cart combination should be moved
with care. Quick stops, excessive
force, and uneven surfaces may
cause the appliance and cart combi­nation to overturn.

AMEUBLES- Cet appareil ne doit

être placé que sur un meuble (avec
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des sur­faces irrégulières risquent de déstabiliser l’ensemble et
de le renverser.

9. Ventilation-Slots and openings in the cabinet and the
back or bottom are provided for ventilation and to
ensure reliable operation of the TV and to protect it
from overheating, these openings must not be blocked
or covered. The openings should never be blocked by
placing the TV on a bed, sofa, rug, or other similar sur­face. This TV should never be placed near or over a
radiator or heat register. This TVshould not be placed
in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufac­turer’s instructions have been adhered to .

10.Power Sources-This TV should be operated only from
the type of power source indicated on the marking
label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local
power company. For TVs intended to operate from bat­tery power, or other sources, refer to the operating
instructions.

11.Grounding or Polarization-This TV is equipped with a
polarized alternating-current line plug(a plug having
one blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety feature.
If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet.
Do not defeat the safety purpose of the polarized plug.

12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or

PORTABLE CART WARNING

S3126A

pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
appliance.

13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV, be sure the anten­na or cable system is grounded so as to provide some
protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPANo. 70, provides information with respect
to proper grounding of the mast and supporting struc­ture, grounding of the lead-in wire to an antenna dis­charge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding elec­trodes, and requirements for the grounding electrode.
(Fig. A)

14.Lightning-For added protection for this TV receiver
during a lightning storm, or when it is left unattended
and unused for long periods of time, unplug it from the
wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV due to lightning
and power-line surges.

15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light of power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact
with them might be fatal.

16.Overloading-Do not overload wall outlets and exten­sion cords as this can result in a risk of fire or electric
shock.

17.Object and Liquid Entry-Never push objects of any
kind into this TV through openings as they may touch
dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of
any kind on the TV.

18.Servicing-Do not attempt to service this TV yourself as
opening or removing covers may expose you to dan­gerous voltage or other hazards. Refer all servicing to
qualified service personnel.

19.Damage Requiring Service-Unplug this TV from the
wall outlet and refer servicing to qualified service per­sonnel under the following conditions:

a. When the power supply cord or plug is damaged or

frayed.

b.If liquid has been spilled, or objects have fallen into

the TV.

c. If the TV has been exposed to rain or water.
d.If the TV does not operate normally by following the

operating instructions. Adjust only those controls that
are covered by the operating instructions, as improper
adjustment of other controls may result in damage and
will often require extensive work by a qualified techni­cian to restore the TV to its normal operation.

e. If the TV has been dropped or damaged in any way.
f. When the TV exhibits a distinct change in perfor-

mance-this indicates a need for service.

20.Replacement Parts-When replacement parts are
required, be sure the service technician uses replace­ment parts specified by the manufacturer that have the
same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, injury to
persons or other hazards.

21.Safety Check-Upon completion of any service or
repairs to this TV, ask the service technician to perform
routine safety checks to determine that the TV is in
proper operating condition.

22.Heat-This TV product should be situated away from
heat sources such as radiators, heat registers, stoves, or
other products (including amplifiers) that produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

ELECTRIC
SERVICE
EQUIPMENT

GROUND
CLAMP

NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING

ELECTRODE SYSTEM
(NEC ART 250, PART H)

S2898A

GROUND CLAMPS

GROUNDING CONDUCTORS
(NEC SECTION 810-21)

ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)

ANTENNA
LEAD IN
WIRE

OPERATING CONTROLS AND FUNCTIONS

- FRONT PANEL -

- REAR PANEL -

1. VIDEO (in) jack- Connect to the video

output jack of a video camera or VCR.

2. AUDIO (in) jack- Connect to the audio

output jack of a video camera or VCR.

3. EARPHONE jack- To connect earphone

(not supplied) for personal listening.

4. MENU button- Press to display the menu

on the TV screen.

5. VOLUME ▲/▼ buttons- Press to control

the volume level.
Press to determine a setting mode from the
menu on the TV screen. (only the VOL ▲
button)
Press to select or adjust from a particular
menu. (for example: Language Selection,
Channel Presetting, Closed Caption Selection,
Picture Adjustment, V-CHIPSet Up)

6. CHANNEL▲/▼ buttons- Press to select

memorized channel.
NOTE:You MUST PRESET channels
BEFORE using CHANNEL ▲ or ▼ button.
(See CHANNEL PRESETTING)
Press to select a setting mode from the
menu on the TV screen.
Press to select item you want to adjust in
the picture control mode.

7. POWER button- Press to turn the TV ON

and OFF.

8. Infrared Sensor Window- Receives the

infrared control signals from the remote
control unit.

9. CHANNELNUMBER button- Press two

digits to directly access the desired channel.
Remember to press a "0" before a single
digit channel.
+100 button- Press to select cable channels
which are equal or greater than number

100.

10.MUTE button- Press the MUTE button to

turn off the sound portion of the TV pro­gram. (Volume level display turns LIGHT
RED from LIGHT BLUE.) Press the
MUTE button again or press the VOL(ume)
▲ or ▼ button to restore sound.

11.CHANNEL RETURN button- Press this

button to go back to the previously viewed
channel. For example, pressing the CHAN­NEL RETURN button once will change
channel display from CH 3 (present chan­nel) to CH 10 (previously viewed channel),
and pressing it a second time will return
from CH 10 to CH 3.

12.DISPLAYbutton- Press to display the

channel number on the screen. If you press
it again, the channel number will disappear.

13.SLEEP button- Press the SLEEP button to

display the sleep timer and start the func­tion. The shut off time can be determined
by the number of times you press the but­ton. (0, 10, 20, 30,..90, 0 minutes)

- REMOTE CONTROL -

VIDEO VOLUME POWERCHANNELMENUEARPHONEAUDIO

12 34 5 6 7 8

ANT.IN

16 15

PWR

123

456

789

0 +100

DISPLAY

VOL

CH

CH

VOL

SLEEP

CHANNEL

RETURN

7

9

5

4

10

12

11

13

MUTE

MENU

6

GAME

14

This manual covers 13" and 19". The operation of the two models are exactly the same except the appearance. 19" model is illustrated in this manual.

14.GAME button- Press to set the Game

mode and external input mode at the same
time. Press the GAME button again to exit
this mode.

15.ANT(enna). IN jack- Connect to an anten-

na, cable system, or satellite system.

16.AC cord- Connect to the standard AC out-

let (120V/60Hz).
NOTE: Remove the AC cord from the
hook to avoid breaking the wire before you
connect to a standard AC outlet.

INSTALLING THE BATTERIES

Slide the battery compartment cover back on
the remote unit.

Insert 2 "AA" penlight batteries into battery
compartment in the direction as indicated by
the polarity (+ / -) markings. Batteries installed
with incorrect polarity may damage the remote
unit.

Replace the cover.

3

2

1

SYMBOLE D'AVERTISSEMENT POUR

LES COMPOSANTES

APPAREIL ET MEUBLE A ROULETTES

S3126A

L1359.QX33 01.5.14 5:52 PM Page 2

LANGUAGE SELECTION

If you want to change the language of the on­screen menu, follow the procedure below.

1)Connect the power cord to a standard AC
outlet.

2)Press the POWER but­ton to turn on the TV.

3)Press the MENU but­ton so that the menu
display appears
on the TV screen.

4)Press the CH(annel) ▲
or ▼ button to point to
"[ENGLISH]".

5)Select "ENGLISH" or
"ESPAÑOL" = Spanish
by using
the VOL(ume) ▲ or ▼ button.

6)Press the MENU button to exit the menu.

CHANNEL PRESETTING

NOTE:You MUST PRESET channels

BEFORE using CHANNEL ▲ or ▼ button.

To preset a channel or to change a preset chan-

nel, follow the procedure below.

1)Press the POWER but­ton to turn on the TV.

2)Press the MENU but­ton so that the menu
display appears
on the TV screen.

3)Press the CH(annel) ▲
or ▼ button to point to
"CHANNEL SET".
Then, press the
VOL(ume) ▲ button.

4)Press the CH(annel) ▲ or ▼ button to point
to "AUTO MEMO". Then, press the

VOL(ume) ▲ button.
The tuner scans and
memorizes all active
channels in your area.

● The TV distinguishes

between standard TV
channels and cable (CATV) channels.

● When AUTO MEMO action is completed,

the lowest memorized channel reappears on
the screen.

● When you press the CH(annel) ▲ or ▼ but-

ton after selecting AUTO MEMO, the tuner
will stop at the memorized channels only.

● The TV may detect TV channels as CATV

channels if the receiving conditions are poor.
In this case, try AUTO MEMO action again
when receiving conditions are better.

[ADD/DELETE FUNCTION]

1)Press the MENU button so that the menu
display appears on the TV screen.

2)Press the CH(annel) ▲ or ▼ button to point
to "CHANNEL SET".
Then, press the VOL(ume) ▲ button.

3)Press the VOL(ume) ▲ button so that
"ADD/DELETE" is selected.

4)Use the CH(annel) ▲
or ▼ button to select
the channel you wish to
put into memory or to
erase from memory.
Note: The display will
return to a normal
screen in about 10 sec­onds.
Perform
"ADD/DELETE" func­tion while this display
appears on the screen.

● Press the VOL(ume) ▲ or ▼ button to light

up the channel number
in LIGHT BLUE if you wish to add the
channel into memory.

● Press the VOL(ume) ▲ or ▼ button to light

up the channel number
in LIGHT RED if you wish to erase the
channel from memory.

5)Press the MENU button to exit the menu.

RESUME FUNCTION

If the power fails or is disconnected while the
TV is powered on, the TV will turn on auto­matically when the power resumes.

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

ADD/DELETE
AUTO MEMO

ADD/DELETE
AUTO MEMO

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

OPERATIONS (continued)

GAME MODE

Set to the most suitable position for TV
GAME.

[+] : ON
[ -] : OFF

BRIGHT

Adjust until the whitest parts of the picture are
as bright as you prefer.

[+] : increase brightness
[ -] : decrease brightness

CONTRAST

Adjust to increase or decrease contrast.

[+] : increase contrast
[ -] : decrease contrast

COLOR

Adjust to be brilliant or pale color.

[+] : be brilliant color
[ -] : be pale color

TINT

Adjust to obtain natural skin tones.

[+] : greenish tone
[ -] : reddish tone

SHARPNESS

Adjust the sharpness.

[+] : soft
[ -] : normal

Notes:

● In the above steps, the picture adjustment

display will disappear from the TV screen
automatically after about 10 seconds if you
do not press any buttons, even though you
may not be finished. Press the MENU and

VOL(ume) ▲ button so that "PICTURE" is
selected. Then, press the CH(annel) ▲ or ▼
button repeatedly until the display returns to
the screen.

● If you adjust the other Picture control after

you set the Game mode to [ON], the Game
mode is set to [OFF] automatically.

[USING THE GAME BUTTON]

You may also set the Game mode and external
input mode at the same time by pressing the
GAME button on the remote control. “GAME”
appears on the TV screen.

● To exit the Game mode and external input

mode, press the GAME button on the remote
control again.

● To cancel the Game mode only, adjust the

picture control. In this case, “VIDEO” instead
of “GAME” appears on the TV screen.

● If you press the GAME button when the TV

is off, the TV turns on and will be in the
Game mode and external input mode auto­matically.

[-]

GAME MODE

[+]

OFF ON

[-]

BRIGHT

[+]

[-]

CONTRAST

[+][-]

COLOR

[+]

[-]

TINT

[+]

[-]

SHAPNESS

[+]

NORMAL SOFT

: Press the CH(annel) ▲ or ▼ button.

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

WATCHING ATV PROGRAM

1)Press the POWER button to turn on the TV.

2)Select the desired channel with the
CH(annel) ▲ or ▼ button.

3)Adjust the volume to the desired listening
level using the VOL(ume) ▲ or ▼ button.

4)Adjust picture controls for a natural looking
image. (See "PICTURE ADJUSTMENT".)

SETTING THE SLEEP TIMER

The sleep timer function enables you to shut
off the power without pressing the POWER
button after a desired time period.

1)Press the POWER but­ton to turn on the TV
and press the SLEEP
button on the remote
control .

2)You may change the
sleep time by pressing the SLEEP
button on the remote control repeatedly. The
timer can be set up to 90 minutes, 10 min­utes each time the SLEEP button is pushed.
(The timer display counts up and sleep timer
will be displayed on the screen when you
press the SLEEP button on remote control.)
Note: When you disconnect the unit from
the AC outlet, or if you have a power failure,
the sleep time will be lost.

CLOSED CAPTION SELECTION

You may view specially labeled (cc) TV pro­grams, movies, news, prerecorded tapes, etc.
with either a dialogue caption or text display
added to the program.

1)Press the MENU button so that the menu
display appears on the TV screen.

2)Press the CH(annel) ▲ or ▼ button to point
to "CAPTION".

3)Press the VOL(ume) ▲ or ▼ button to select
the mode you wish.

4)When done, press the MENU button to exit
the menu.

PREPARATION FOR USE

OPERATIONS

SLEEP 10

To cancel the sleep timer:

Press the SLEEP button repeatedly until
"SLEEP 0" is displayed.

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [ C1]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [ C2]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [ T1]

PICTURE
CHANNEL SET
[ENGLISH]ESPAÑOL
V-CHIP SET UP
CAPTION [ T2]

: Press the VOL(ume) ▲ or ▼ button.

V-CHIP SET UP

V-CHIP enables parents to prevent their chil­dren from watching inappropriate material on
TV.
V-CHIP reads the ratings for programming
(except for news and sports programs, unedited
movies on premium cable channels, and
Emergency Broadcast System signals), then
denies access to programming if the program's
rating meets the limitations you select. In this
case, "PROTECTED PROGRAM by ..." mes­sage appears on the TV screen. You can watch
the protected program by entering access code
(default 0000).
To block certain ratings, follow the steps
below.

● Programming may be rated by the Motion

Picture Association of America (MP AA) or
according to the Television Parental
Guidelines. In order to block any inappropri­ate programming, set your limits in both
places (MPAA RATING and TV RATING).

● You cannot access the menu when the

"PROTECTED PROGRAM by ..." message
appears. In this case, change to the
unblocked channel, then press the MENU
button.

[MPAARATING SET UP]

1)Press the MENU but­ton so that the menu
display appears on the
TV screen.

2)Press the CH(annel) ▲
or ▼ button to point to
"V-CHIP SET UP".
Then, press the
VOL(ume) ▲ button.

3)Use the number but­tons to enter 4-digit
access code. The
default access code is

0000. If you have not
set up your personal

access code, you should use 0000.

4)Press the CH(annel) ▲ or ▼ button to point
to "MPAA RATING".
Then, press the
VOL(ume) ▲ button.

5)Press the CH(annel) ▲
or ▼ button to point to
your desired item.
Then, press the VOL(ume) ▲ button to
select [BLOCK] or [VIEW].

● When you select the rating category and turn

it [BLOCK], the higher rating will turn
[BLOCK] automatically. Also, the lower rat­ing will turn [VIEW] automatically.

● When you turn "G" to [BLOCK] or [VIEW],

the all ratings will turn to [BLOCK] or
[VIEW] automatically.

● When you turn "X" to [VIEW], then all rat-

ings will turn to [VIEW] automatically.

6)Press the MENU button to exit the menu.

[TV RATING SET UP]

1)Press the MENU but­ton so that the menu
display appears on the
TV screen.

2)Press the CH(annel) ▲
or ▼ button to point to
"V-CHIP SET UP".
Then, press the
VOL(ume) ▲ button.

3)Use the number but­tons to enter 4-digit
access code. The
default access code is 0000. If you have not

PICTURE
CHANNEL SET
[ENGLISH] ESPAÑOL

B V-CHIP SET UP

CAPTION [OFF]

TV RATING

B MPAA RATING

CHANGE CODE

ACCESS CODE

- - - -

B G [VIEW]

PG [VIEW]
PG-13 [VIEW]
R [VIEW]
NC-17 [VIEW]
X [VIEW]

<Selection> <Rating Category
Explanations>

• G: General Audience

• PG: Parental Guidance suggested.

• PG-13: Unsuitable for children under 13

• R: Restricted; under 17 requires

accompanying
parent or adult guardian

• NC-17: No one under 17 admitted

• X: Mature audience only

PICTURE
CHANNEL SET
[ENGLISH] ESPAÑOL

B V-CHIP SET UP

CAPTION [OFF]

ACCESS CODE

- - - -

PICTURE ADJUSTMENT

1)Press the MENU button so that the menu
display appears on the TV screen.

2)Press the VOL(ume) ▲ button so that "PIC­TURE" is selected.

3)Select the feature you wish to adjust with
the CH(annel) ▲ or ▼ button and adjust it
with the VOL(ume) ▲ or ▼ button.

L1359.QX33 01.5.14 5:52 PM Page 3