FUNAI Service manual / Схема, сервісна інструкція Service manual & schematics

Page 1

14" COLOR TELEVISION MS-14 MS-14

Page 2

IMPORTANT SAFETY NOTICE

Proper service and repair is important to the safe, reliable operation of all Funai Equipment. The service procedures recommended by Funai and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.

It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. Funai could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, Funai has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by Funai must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.

General Specifications	1-1
Performance Specifications	2-1
Important Safety Precautions	3-1
Disassembly Instructions	4-1
Electrical Adjustment Instructions	5-1
Block Diagram	6-1
Schematic Diagrams / PCB's and Test Points	7-1
Waveforms	8-1
Wiring Diagram	9-1
Exploded View	10-1
Mechanical Parts List	11-1
Electrical Parts List	12-1

GENERAL SPECIFICATIONS *

FEATURE and SPECIFICATIONS

Color System: PAL - B/G SECAM - B/G. D/K NTSC 3.58/4.43MHz (Video Plavback) Tuning System: Voltage Synthesizer Receivable Channels: VHF-I · B1~B5/ E2~E4 ch (X~S2) (CATV ch) VHE-H B6~B12/ E5~E12 ch (S3~S10) UHE: 21~69 Number of Preset: Up to 50 Antenna Impedance: LIHE/VHE 750 Inhalanced Picture Tube: 14" Tinted Picture Control: Color. Brightness Contrast and Video mode (Sharp/Soft) Picture Control Memory: Standard Select 77mm Round 80 Output Power 1W ~ 2 Other Features Automatic Channel Preset Automatic Degaussing Power Source: 110~240V 50/60Hz AC (Auto Voltage) Power Consumption: 70W Cabinet Size 366(W) × 350(D) × 322(H) mm (Approx.) 9kg (Approx.) SASO Passable

Regulations:

JACKS and TERMINALS

Speaker:

Weight:

UHF/VHF Antenna: IEC (75Ω) Video In/Out: BNC × 2 Audio In/Out: BCA x 2 Farphone. CES (ø3.5mm)

CONTROL and SWITCHES

Power^. Push (Front) Channel Up/Down: Push (Front) Volume Up/Down: Push (Front) Tuning Up/Down: Push (Front) Program: Push (Front) Push (Front) Auto Memo / Band REMOTE CONTROL : Standby (20kevs) Mute Channel Lin/Down Control/Volume Up/Down 0/AV Sleep 1~9 Picture Select (Bright / Contrast / Color / Video Mode) Previous Display DISPLAY LED Indicator Stand-by * When turning on the power button stand-by LED is put off On Screen Display: Channel Volume Briahtness Color Contrast Sharp-Soft Sleep Timer (10~90 Minute) Tuning Indicator

ACCESSORIES

Remote Control Unit Battery: UM3×2 Owner's Manual Rod Antenna

Band Position

* Specifications are subject to change without notice.

Page 3

PERFORMANCE SPECIFICATIONS

ANT, Input ------75Ω Unbalanced, IEC connector

< Tuner >

< Deflection >

Reference Level 300mVp-p at Video Output Test Input Signal 400Hz 30% modulation
Description	Condition	Unit	Nominal	Limit
1. Peak Picture Sens	VHF UHF	dBμV dBμV	20 30	30 40
AFT Pull In Range (80dBµ input)	_	MHz	± 1.0	± 0.7
3. Intermediate Freq.	Picture Sound Sound	MHz MHz MHz	38.0 31.5 (D/K) 32.5 (B/G)
4. Intercarrier Freq.		MHz MHz	6.5 (D/K) 5.5 (B/G)

< Video & Chroma>

Description	Condition	Unit	Nominal	Limit
1. Misconvergence	Center	mm		0.4
	Side	mm		1.5
	Corner	mm		2.0
2. Over Scan	Horizontal	%	10	—
	Vertical	%	10
3. Color Temperature	—	к	8000K-10MPCD	—
4. Resolution	Horizontal	Line	300
	Vertical	Line	300	—
5. Brightness	APL 100%	Ft-L	45	35

<Audio>

All items are measured across 16Ω resistor at speaker output terminal.

Description	Condition	Unit	Nominal	Limit
1. Deflection Freq.	Horizontal (PAL/SECAM)	KHz	15.625
	(NTSC)	KHz	15.75
	Vertical (PAL/SECAM)	Hz	50
	(NTSC)	Hz	60	—
2. Linearity	Horizontal	%	_	± 15
	Vertical	%		± 15
3. High Voltage	_	κv	23	_

Description	Condition	Unit	Nominal	Limit
1. Audio Output Power	10% THD	w	1.2	0.8
2. Audio Distortion	500mW	%	2	5
3. Audio Freq. Response	-6dB	Hz	_	100~6K

2-2

Page 4

IMPORTANT SAFETY PRECAUTIONS

Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.

Safety Precautions for TV Circuit

1. Before returning an instrument to the customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the picture tube and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer.

Repeat this test with the instrument AC switch in the off position.

d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester. With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milliampere. Reverse the instrument power cord plug in the outlet and repeat the test.

ANY MEASUREMENTS NOT WITHIN THE LIM-ITS SPECIFIED HEREIN INDICATE A POTEN-TIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE IN-STRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSO-RIES.

e. x-Radiation and High Voltage Limits Because the picture tube is the primary potential source of X-radiation in solid-state TV receivers it is specially constructed to prohibit X-radiation emissions. For continued X-radiation protection. the replacement picture tube must be the same type as the original. Also, because the picture tube shields and mounting hardware perform an X-radiation protection function, they must be correctly in place. High voltage must be measured each time servicing is performed that involves B+, horizontal deflection or high voltage. Correct operation of the X-radiation protection circuits also must be reconfirmed each time they are serviced. (X-radiation protection circuits also may be called "horizontal disable" or "hold down.") Read and apply the high voltage limits and, if the chassis is so equipped, the X-radiation protection circuit specifications given on instrument labels and in the Product Safety & X-Radiation Warning note on the service data chassis schematic. High voltage is maintained within specified limits by close tolerance safety-related components/adjustments in the high-voltage circuit. If high voltage exceeds specified limits, check each component specified on the chassis schematic and take corrective action
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the picture tube.
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Picture Tube Implosion Protection Warning -The picture tube in this receiver employs integral implosion protection. For continued implosion protection, replace the picture tube only with one of the same type number. Do not remove, install, or otherwise handle the picture tube in any manner without first putting on shatterproof goggles equipped with side shields. People not so equipped must be kept safely away while picture tubes are handled. Keep the picture tube away from your body. Do not handle

the picture tube by its neck. Some "in-line" picture tubes are equipped with a permanently attached deflection yoke; because of potential hazard, do not try to remove such "permanently attached" yokes from the picture tube.

5. Hot Chassis Warning -

a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and may be safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0V is obtained. *remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground. b. Some TV receiver chassis have a circuit which obtain voltage about 70% of AC voltage between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.

c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered. Note: * In case unit has no polarity AC plug only.

6. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
7. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
8. Product Safety Notice Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual

Page 5

nents rated for higher voltage, wattage, etc.. Parts that have special safety characteristics are identified by a ( A) on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The Product's Safety is under review continu-

inspection, nor can the protection they give neces-

sarily be obtained by replacing them with compo-

Precautions during Servicing

A. Parts identified by the ( A ) symbol are critical for safety. Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements. Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
- 1) Wires covered with PVC tubing
- 2) Double insulated wires
- 3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
- 1) Insulation Tape
- 2) PVC tubing
- 3) Spacers
- 4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.

H. When a power cord has been replaced, check that 10-15 kg of force in any direction will not loosen it.

ously and new instructions are issued whenever

appropriate. Prior to shipment from the factory our

products are strictly inspected to confirm with the

recognized product safety and electrical codes of the

countries in which they are to be sold. However, in

order to maintain such compliance, it is equally im-

portant to implement the following precautions when

a set is being serviced.

I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets. etc.) do not remain inside the set.
K. Crimp type wire connector
When replacing the power transformer in sets where the connections between the power cord and power transformer primary lead wires are performed using crimp type connectors, in order to prevent shock hazards, perform carefully and precisely the following steps.
Replacement procedure
Remove the old connector by cutting the wires at a point close to the connector. Important: Do not re-use a connector (discard it). Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist
the strands to avoid frayed conductors.
3) Align the lengths of the wires to be connected. Insert the wires fully into the connector. 4) Use the crimping tool to crimp the metal sleeve at the center position. Be sure to crimp
fully to the complete closure of the tool.
L. When connecting or disconnecting the VCR connectors, first, disconnect the AC plug from AC supply socket.

TVSFME

Safety Check after Servicing

Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.

1. Clearance Distance

When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)

Table 1 : Ratings for selected area

AC Line Voltage	Region	Clearance Distance (d) (d')
110 to 240 V	Middle and Near East	≥ 4mm (d) ≥ 6mm (d')

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

2. Leakage Current Test

Confirm specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.).

Measuring Method : (Power ON)

Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.

Table 2 : Leakage current ratings for selected areas

AC Line Voltage	Region	Load Z	Leakage Current (i)	Earth Ground (B) to:
		2kΩ RES.	i≤0.7mA rms	Antonna terminals
110 to 240 V	110 to 240 V Middle and Near East	in connected	i≤2mA dc
110 to 240 V	110 to 240 V Middle and Near East	50kΩ RES.	i≤0.7mA rms	Otherterminale
		in connected	i≤2mA dc	Other terminals

3-4

Note: This table is unofficial and for reference only. Be sure to confirm the precise values.

Page 6

DISASSEMBLY INSTRUCTIONS

1. DISASSEMBLY FLOW CHART

This flow chart indicates the disassembly steps of the cabinet parts and PCB in order to gain access to item(s) to be serviced. When reassembling, perform the step(s) in the reverse order. Bend, route and dress the cables as they were originally.

CAUTION !: When removing the CRT, make sure to discharge Anode Lead of the CRT. Use the CRT Ground Wire to discharge the CRT before removing the Anode Cap.

2. DISASSEMBLY METHOD

STEP			REMOVAL
/ LOC. NO.	PART	FIG. NO.	REMOVE / *UNLOCK / RELEASE / UNPLUG / UNCLAMP / DESOLDER	NOTE
[1]	Rear Cabinet	CAB1 CAB2	L2 (4pcs), L3	1
[2]	CRT PCB	CAB4 CAB5	CN602, CN603, CN604 FOCUS WIRE, SCREEN WIRE	2
[3]	Main PCB	CAB3 CAB5	CN201, CN202, CN203, CN204, CN208, CN501 ANODE CAP, FOCUS WIRE, SCREEN WIRE	3
[4]	IF PCB	CAB3	CN101, CN102	4
[5]	CRT	CAB4	B2 (4pcs)	5

Reference <Notes> in Table

1. (1) Remove 6 screws (L2, L3) and slide the Rear Cabinet backward.
2. (1) If not already removed, first remove the Rear Cabinet. (2) Remove all relative wires, then pull the CRT PCB backward.
3. (1) If not already removed, first remove the Rear Cabinet. (2) Remove all relative wires on the Main PCB and remove the Anode Cap, then slide the main PCB backward.
4 (1) If not already removed, first remove the Rear Cabinet. (2) Desolder CN101 and CN102, then remove the IF PCB from the Main PCB.

Caution !

Discharge Anode Lead of the CRT with the CRT Ground Wire before removing the Anode Cap.

5. (1) If not already removed, first remove the Rear Cabinet and Main PCB.
- (2) Remove 4 screws (B2), then the CRT can be removed.

Page 7

Page 8

Page 9

ELECTRICAL ADJUSTMENT INSTRUCTIONS

NOTE:

Electrical adjustments are required after replacing circuit components. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.

TEST EQUIPMENT REQUIRED:

1. IF Sweeper
2. DC Volt Meter
3. Oscilloscope: Dual Trace with 10:1 probe
4. PAL, SECAM and NTSC Pattern Generator
5. Monoscope
6. Color Analyzer

HOW TO SET UP THE ADJUSTMENT MODE:

Preset Mode: Press picture select button on the remote control unit, then press the number "1" button.

Brightness ----- Center

Contrast ----- Approx 70%

1. POWER SUPPLY DC VOLTAGE ADJUSTMENT

Purpose: To get correct voltage.

Symptom of Misadjustment: If voltage is incorrect, picture is dark.

Reference Notes: D245, VR205 --- MAIN PCB

1. To inactivate FBT, ground the base of Q220.
2. Connect both terminal of C343 by 1KΩ (60W~80W).
3. Connect the equipment as shown in the above table.
4. Adjust VR205 for reading +114±0.5V on the DC Volt Meter.

2. 38.0MHz PEAK ADJUSTMENT (for TUNER)

Purpose: To adjust PIF (Picture Intermediate Frequency). Symptom of Misadjustment: Beat may appear on the picture and buzz may sound.

Reference Notes: IC101, L106 --- IF PCB

1. Connect Output of sweeper to 6pin of IC101.

Frequency set of sweeper are below:

(1) 31.5MHz (2) 32.4MHz (3) 33.57MHz (4) 35.8MHz (5) 38.0MHz (6) 39.45MHz

5-2

2. Connect the oscilloscope to 16pin of IC101.

17480FA

3. Load DC Voltage to 4pin of IC101 as the wave of oscilloscope not to clip.

4. Adjust L106 as the marker for 38.0MHz to be peak.

Page 10

3. AFT CURVE ADJUSTMENT (for TUNER)

Purpose: To operate AFT correctly.

Symptom of Misadjustment: AFT does not work correctly and/or synchronism will be faulty.

Test Point	Adjustment Point	Input
IC101 6pin, 11pin	L107
Equip	oment	Spec.
IF Sweeper,	Oscilloscope	See below
	Fi	jure
38.0MHz

Reference Notes: SW206 --- MAIN PCB IC101, L107 --- IF PCB

1. Connect output of sweeper to 6pin of IC101. Frequency set is the same as for 38.0MHz Peak Adjustment
Frequency set is the same as for 38.0MHz Peak Adjustment.
2. Connect the oscilloscope to 11pin of IC101.
3. Push SW206 to disengage AFT action.
4. Adjust L107 as the marker for 38.0MHz to the center of AFT curve.

4. RF AGC ADJUSTMENT (for TUNER)

Purpose: Set AGC (Auto Gain Control) Level.

Symptom of Misadjustment: AGC does not synchronize correctly when RF Input Level is weak and distortion may cause on the picture when it is strong.

Test Point	Adjustment Point	Input
TU201 6pin	VR101	PAL Color Bar
Equi	oment	Spec.
PAL Pattern Gener	ator, DC Volt Meter	DC +4.1±0.1V
	Connectio	ns of M. EQ.
		DC Volt Meter
		) ② ① TU201

Reference Notes: TU201 --- MAIN PCB VR101 --- IF PCB

1. Receive the PAL Color Bar signal for 2ch (48.25MHz). (RF input level 80dBµV at the best syncronized point)
2. Connect the equipment as shown in the above table.
3. Adjust VR101 for reading +4.1±0.1V on the DC Volt Meter.

5. 4.43MHz ADJUSTMENT

Purpose: To adjust the color sub-carrier frequency of PAL and SECAM. Symptom of Misadjustment: No color when receiving PAL and SECAM signal.

Test Point	Adjustment	Point		Input
Screen	C299			PAL Red Raster
Equip	ment			Spec.
PAL Patterr	n Generator			See below
		Fi	gure
			(Pink)	Picture is rolling or unstable.
	$\downarrow$		C299>
			(Purple)
	$\bigvee$
		Whole	e Screen Red	Picture is stable.

Reference Notes: C299 --- MAIN PCB

1. Input the PAL Red Raster.
2. Check picture. A. If Red picture is stable. .....OK
- B. If Red picture is rolling or unstable, adjust C299 untill stable.

6. 3.58MHz ADJUSTMENT

Purpose: To adjust the color sub-carrier frequency of NTSC. Symptom of Misadjustment: No color when receiving NTSC signal.

Test Point	Adjustment Point	Input
Screen	C298	NTSC Red Raster
Equipment		Spec.
NTSC Pattern Generator		See below

Reference Notes: C298 --- MAIN PCB

1. Input the NTSC Red Raster.

2. Check picture. Procedure is the same as for 4.43MHz Adjustment.

Page 11

7. V. SIZE ADJUSTMENT

Purpose: To get correct vertical size of screen image.

Symptom of Misadjustment: Vertical size of screen image may not be properly displayed.

Test Point	Adjustment Point	Input
Screen	VR204	Monoscopic Pattern
Equip	oment	Spec.
Mono	scope	90±5%
	Fig	ure

Reference Note: VR204 --- MAIN PCB

1. Operate the unit more than 20 minutes.
2. Input the Monoscopic Pattern.
3. Adjust VR204 so that the vertical size will be 90±5% of Monoscopic Pattern and the circle is round.

8. CUT OFF ADJUSTMENT

Purpose: To adjust the beam current of R, G, B and screen voltage. Symptom of Misadjustment: White color may be reddish, greenish or bluish.

When the screen voltage is too high, the scanning line is appeared on the screen.

Reference Notes: VR601, VR602, VR603, VR604, VR605, VR606 --- CRT PCB

SW209 --- MAIN PCB
Screen-VR --- MAIN PCB (FBT)
1. Operate the unit more than 20 minutes.
2. Degauss the CRT using Degaussing Coil.
3. Input the Black Raster.
4. Turn the Screen-VR (FBT) fully counterclockwise.
Set VR602 (B. Drive), VR603 (R. Drive), VR604 (B. Cut Off), VR605 (G. Cut Off), VR606 (R. Cut Off) and VR601 (Sub Bright) to center.
6. Set the SW209 (Service SW) to ON.
7. Slowly turn the Screen-VR (FBT) to the point where horizontal line just visible.
8. Adjust VR604 (Blue), VR605 (Green) and VR606 (Red) so that horizontal line becomes pure white.
9. Turn off the SW209 (Service SW).

Note: Confirm that White Balance Adj. is correct after this adjustment, and attempt White Balance Adj. if needed.

Page 12

9.1 H DELAY LINE ADJUSTMENT (for PAL)

Purpose: To get correct 1H delay line when the PAL signal is entered. Symptom of Misadjustment: The Anti-PAL signal part is colored when the Philips Pattern is entered. Each scanning line is colored on the color bar.

Reference Notes: D230, TP1, TP5, L210, VR202, VR203 --- MAIN PCB

1. Input the Philips Pattern.
2. Connect the equipment as shown in the above table.
3. Adjust VR202 VR203 and L210 so that the amplitude at Anti-PAL signal part becomes minimum (no color) and the waveform at the color bar part is not seen in double ("Venetian Blind" does not appear at the color bar signal part).

10. BELL FILTER ADJUSTMENT (for SECAM)

Purpose: To adjust the center frequency of SECAM bell filter. Symptom of Misadjustment: The color will be reversed when the SECAM signal is entered.

Reference Notes: D230, TP1, TP2, L216 --- MAIN PCB
1. Input the SECAM Color Bar signal.
The Contrast, Bright and Color control to center.
2. Connect the equipment as shown in the above table.
3. Set oscilloscope to 10 : 1 probe, AC 5mV/div and Range 10µs/div.
4. Adjust L216 with core driver to flat waveform.

Page 13

11. R-Y DEMODULATE COIL ADJUSTMENT (for SECAM)

Purpose: To adjust the level of R-Y color difference signal. Symptom of Misadjustment: The R, G and B will be unbalanced.

Reference Notes: D230, TP1, TP3, L212 --- MAIN PCB

1. Connect the equipment as shown in the above table.

2. Input the SECAM Black Raster.

3. Adjust L212 with core driver so that ① becomes center of ② as shown in the above table.

12. B-Y DEMODULATE COIL ADJUSTMENT (for SECAM)

Purpose: To adjust the level of B-Y color difference signal. Symptom of Misadjustment: The R, G and B will be unbalanced.

Reference Notes: D230, TP1, TP4, L211 --- MAIN PCB

1. Connect the equipment as shown in the above table.

2. Input the SECAM Black Raster.

^3. Adjust L211 with core driver so that ① becomes center of ② as shown in the above table.

L7480EA

Page 14

13. SUB BRIGHT ADJUSTMENT

Purpose: To get proper brightness.

Symptom of Misadjustment: Proper brightness cannot be obtained by adjusting the Bright Control.

Test Point	Adjustment Point	Input
Screen	VR601	Gray Scale pattern
Equip	ment	Spec.
Pattern G	ienerator	See below
	Fig	ure
	This bar	Just visible Black

Reference Notes: VR601 --- CRT PCB

1. Operate the unit more than 20 minutes.

2. Input the 8-step Gray Scale pattern.

3. Adjust VR601 so that the bar is just visible. (See above figure)

14. FOCUS ADJUSTMENT

Purpose: To get correct focus.

Symptom of Misadjustment: Blurred image is shown on the display.

Test Point	Adjustment Point	Input
Screen	Focus-VR (FBT)	Monoscopic Pattern
Equi	pment	Spec.
Mono	oscope	See below
	Fig	jure

Reference Note: Focus-VR (FBT) --- MAIN PCB

1. Operate the unit more than 20 minutes.

2. Input the Monoscopic Pattern.

3. Adjust Focus-VR (FBT) to be obtained clear picture.

L7480EA

Page 15

EXPLODED VIEW

80EA

Page 16

MECHANICAL PARTS LIST

PRODUCT SAFETY NOTE: Products marked with a A have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.

Ref. No.	Description	Part No.
A 1	FRONT CABINET ASS'Y	0EM300562
A1-1*	FRONT CABINET	0EM000113
A 1- 2	CONTROL PANEL	0EM200553
A 1- 3	SENSOR WINDOW	0EM401486
A 1- 4	LED INDICATOR	0EM401470
A 1- 5	BRAND BADGE	0EM400975
A 2	REAR CABINET ASS'Y	0EM300563
A 2-1	REAR CABINET	0EM000114
A 2- 2 \Lambda	RATING LABEL	0EM401501
A 2- 3	JACK PLATE	0EM401488
A 3	(See Electrical Parts List)

B 1	TENSION SPRING	26WH006
B 2	CRT MOUNTING SCREW	8A00083
В 3	(See Electrical Parts List)
B 4	(See Electrical Parts List)
B 5	(See Electrical Parts List)

L 1	(See Electrical Parts List)
L 2	SCREW P-TIGHT BIND HEAD 4X18	GBMP4180
L 3	SCREW P-TIGHT BIND HEAD 4X12	GBMP4120

	ACCESSORIES
	REMOTE CONTROL UNIT	UREMT20MM007
	DRY BATTERY UM-3(K) 2PCS PACK or	1813020
	DRY BATTERY UM3/RS6 2PCS PACK	579W099
	OWNER'S MANUAL	0EMN00644
	ROD ANTENNA	0EMN00542
1

* Material certificate is required to attach.

ELECTRICAL PARTS LIST

Ref. No.

C 242

C 243

C 244

C 245

C 246

C 247

C 249

Description

ELECTROLYTIC CAP. 100µF/35V M

ELECTROLYTIC CAP. 2.2µF/50V M

ELECTROLYTIC CAP. 10µF/50V M

ELECTROLYTIC CAP. 470uF/25V M or

ELECTROLYTIC CAP 470UE/25V M W/E

METALIZED FILM CAP 0.39uE/200V J or

ECTROLYTIC CAP. 22µF/35V M

CHIP RES. 1/10W J 0Ω

Part No.

RRXAJBBZ0000

126F225S

126F106S

CE1EMZNTL471

626D477

122Z180

1220510 2250104S 126F105S CHE1JKB0B103

126F225S

126E106S

126F106S 2250823S

CE1CMZDDL471

CE1CMZNTL471

CE1EMZDDL471

CE1EMZNTL471

CA2E010NC009

CE1GMZDDL331

CE1GMZNTI 331

626E337 CE2AMADDL010 CE2AMANTL010 122Z183

1220496

1227279

1220493

CE2CMADDLR47 CE2CMANTLR47 CCD2JKS0B222 CA2C470NC009

CE2CMZDEH470

126F475S

626D477

626C477

CBP2DKD00394

126E107S 126E226S

NOTE: Parts that not assigned part number (------) are not available.

Tolerance of Capacitors and Resistors are noted with the following symbols

C±0.25%	F±1%	J±5%	M±20%	Z+80/-20%
D±0.5%	G±2%	K±10%	N±30%

MMA PCB ASSEMBLY

Ref. No.	Description	Part No.
	MMA PCB ASSEMBLY	0ESA00352
	Consists of the following:
Δ	PCB (MAIN+CRT+IF)	BL7403F010B1
	MAIN PCB (MMA-A)
	CRT PCB (MMA-B)
	IF PCB (MMA-C)

MAIN PCB (MMA-A)

Ref. No.	Description	Part No.		METALIZED FILM CAP. 0.39µF/200V J or
	MAIN PCB (MMA-A)			METALIZED FILM CAP. 0.39µF/200V J
	Consists of the following:		C 250	MYLAR CAP. 0.1µF/50V K
	CAPACITORS		C 251	ELECTROLYTIC CAP. 1µF/50V M
C 202	ELECTROLYTIC CAP. 10µF/50V M	126F106S	C 252	CHIP CERAMIC CAP. B K 0.01µF/50V
C 203	ELECTROLYTIC CAP. 4.7µF/50V M	126F475S	C 253	ELECTROLYTIC CAP. 2.2µF/50V M
C 209	ELECTROLYTIC CAP. 4.7µF/50V M	126F475S	C 254	ELECTROLYTIC CAP. 10µF/50V M
C 211	ELECTROLYTIC CAP. 4.7µF/50V M	126F475S	C 255	ELECTROLYTIC CAP. 10µF/50V M
C 212	ELECTROLYTIC CAP. 220µF/6.3V M	126A227S	C 256	MYLAR CAP. 0.082µF/50V K
C 213	ELECTROLYTIC CAP. 1µF/50V M	126F105S	C 257	ELECTROLYTIC CAP. 470µF/16V M or
C 214	CHIP CERAMIC CAP. F Z 0.022µF/50V	CHE1JZB0F223		ELECTROLYTIC CAP. 470µF/16V M or
C 215	ELECTROLYTIC CAP. 10µF/50V M	126F106S		ELECTROLYTIC CAP. 470µF/16V M
C 216	•MYLAR CAP. 0.18µF/50V K	2250184S	C 259	ELECTROLYTIC CAP. 470µF/25V M or
C 217	ELECTROLYTIC CAP. 10µF/50V M	126F106S		ELECTROLYTIC CAP. 470µF/25V M or
C 218	ELECTROLYTIC CAP. 10µF/50V M	126F106S		ELECTROLYTIC CAP. 470µF/25V M W/F
C 219	ELECTROLYTIC CAP. 1µF/50V M	126F105S	C 260	ELECTROLYTIC CAP. 1µF/250V M(105°C)
C 220	CHIP CERAMIC CAP. SL J 120pF/50V	CHE1JJBSL121	C 261	ELECTROLYTIC CAP. 330µF/35V M or
2 221	ELECTROLYTIC CAP. 2.2µF/50V M	126F225S		ELECTROLYTIC CAP. 330µF/35V M or
224	CHIP CERAMIC CAP. CH J 240F/50V	CHE1JJBCH240		ELECTROLYTIC CAP. 330µF/35V M W/F
225	CHIP CERAMIC CAP. CH J 240F/50V	CHE1JJBCH240	C 262	ELECTROLYTIC CAP. 1µF/100V or
C 229	CHIP CERAMIC CAP. F Z 0.01µF/50V	CHE1JZB0F103		ELECTROLYTIC CAP. 1µF/100V
C 230	ELECTROLYTIC CAP. 47µF/16V M	126C476S	C 263	METALIZED FILM CAP. 0.0047µF/1.6KV or
C 232	CHIP CERAMIC CAP. SL J 100pF/50V	CHE1JJBSL101		METALIZED FILM CAP. 0.0047µF/1.6KV J
C 233	ELECTROLYTIC CAP. 10HF/50V M	126F106S	C 264	METALIZED FILM CAP. 0.0027µF/1.6KV J or
C 234	ELECTROLYTIC CAP. 10µF/50V M	126F106S		METALIZED FILM CAP. 0.0027µF/1.6KV J
C 235	ELECTROLYTIC CAP. 10µF/50V M	126F106S	C 265	ELECTROLYTIC CAP. 0.47µF/160V or
C 236	CHIP CERAMIC CAP F Z 0.01µF/50V	CHE1JZB0F103		ELECTROLYTIC CAP. 0.47µF/160V
C 237	CHIP CERAMIC CAP. SL J 47pF/50V	CHE1JJBSL470	C 268	CERAMIC CAP. B K 2200pF/500V
C 238	MYLAR CAP. 0.001µF/50V K	2250102S	C 271	ELECTROLYTIC CAP.
C 239	MYLAR CAP. 0.0022µF/50V K	2250222S		47μF/160V M (105°C) or
C 240	MYLAR CAP. 0.1µF/50V K	2250104S		ELECTROLYTIC CAP. 47µF/160V M
C 241	CHIP CERAMIC CAP BK 0.00111E/50V	CHE1.IKB0B102	C 273	ELECTROLYTIC CAP. 4.7µF/50V M

* Mylar is a registered trademark of E. I. Du Pont de Nemours and Company

L7483CA

12-1

Page 17

Ref. No.	Description	Part No.		Ref. No.	Description	Part No.
C 276	ELECTROLYTIC CAP. 0.22µF/50V M	126F224S		C 344	ELECTROLYTIC CAP. 3300µF/25V M or	CE1EMZZTL332
C 277	CHIP CERAMIC CAP. SL J 33pF/50V	CHE1JJBSL330			ELECTROLYTIC CAP. 3300µF/25V M W/F	126D338
C 278	ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZDDL471		C 345	ELECTROLYTIC CAP. 47µF/16V M	126C476S
	ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZNTL471		C 346	ELECTROLYTIC CAP. 2200µF/25V M	CE1EMZNTL222
	ELECTROLYTIC CAP. 470µF/16V M	626C477		C 347	ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZDDL471
C 279	ELECTROLYTIC CAP. 1µF/50V M	126F105S			ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZNTL471
C 280	ELECTROLYTIC CAP. 1µF/50V M	126F105S			ELECTROLYTIC CAP. 470µF/16V M	626C477
C 281	ELECTROLYTIC CAP. 1µF/50V M	126F105S		C 348	ELECTROLYTIC CAP. 2.2µF/50V M	126F225S
C 282	ELECTROLYTIC CAP. 1µF/50V M	126F105S		C 363	ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZDDL471
C 283	ELECTROLYTIC CAP. 1µF/50V M	126F105S			ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZNTL471
C 284	ELECTROLYTIC CAP. 4.7µF/50V M	126F475S			ELECTROLYTIC CAP. 470µF/16V M	626C477
C 285	STACKED FILM CAP. 0.22µF/50V J or	125U224S		C 364	MYLAR CAP. 0.1µF/50V K	2250104S
	STACKED FILM CAP. 0.22µF/50V J	125R224S		C 365	CHIP CERAMIC CAP. FZ 0.022µF/50V	CHE1JZB0F223
C 286	STACKED FILM CAP. 0.22µF/50V J or	125U224S		C 366	MYLAR CAP. 0.0022µF/50V K	2250222S
	STACKED FILM CAP. 0.22µF/50V J	125R224S		C 368	CHIP CERAMIC CAP. B K 0.001µF/50V	CHE1JKB0B102
C 287	STACKED FILM CAP. 0.22µF/50V J or	125U224S		C 370	MYLAR CAP. 0.1µF/50V K	2250104S
	STACKED FILM CAP. 0.22µF/50V J	125R224S		C 372	CERAMIC CAP. CH D 10pF/50V	12CH100S
C 288	SEMICONDUCTOR CAP. SR K 0.047µF/25V	12Y2473S		C 375	ELECTROLYTIC CAP. 47µF/16V M	126C476S
C 289	CHIP CERAMIC CAP. B K 0.001µF/50V	CHE1JKB0B102		C 376	CERAMIC CAP. 1000pF/1KV or	CCD3AKP0E102
C 290	CHIP CERAMIC CAP. FZ 0.022µF/50V	CHE1JZB0F223			CERAMIC CAP. 1000pF/1KV	6220574
C 291	ELECTROLYTIC CAP. 1µF/50V M	126F105S		C 377	CERAMIC CAP. CH J 47pF/50V	12CH470S
C 292	CHIP CERAMIC CAP. FZ 0.01µF/50V	CHE1JZB0F103		C 378	ELECTROLYTIC CAP. 1000µF/16V M W/F or	CE1CMZDDL102
C 293	ELECTROLYTIC CAP. 100µF/16V M	126C107S			ELECTROLYTIC CAP. 1000µF/16V M or	CE1CMZNTL102
C 294	FILM CAP. 0.47µF/50V J or	125U474S			ELECTROLYTIC CAP. 1000µF/16V M W/F	626C108
	FILM CAP. 0.47µF/50V J	125R474S		C 379	ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZDDL471
C 295	STACKED FILM CAP. 0.15µF/50V J or	125U154S			ELECTROLYTIC CAP. 470µF/16V M or	CE1CMZNTL4/1
	STACKED FILM CAP. 0.15µF/50V J	125R154S			ELECTROLYTIC CAP. 4/0µF/16V M	6260477
C 296	ELECTROLYTIC CAP. 0.47µF/50V M	126F474S		C 501 🛆	CERAMIC CAP./SAFETY E M	CCG2HMP0E222
C 297	CHIP CERAMIC CAP. B K 0.001µF/50V	CHE1JKB0B102			CEDAMIC CAR SAFETY 0.0022UE	1220621
C 298		CVC300011008		C 502	CERAMIC CAP (SAFETY E M	CCG2HMP0E222
C 299				0 302 75	2200pF/AC125V or
0 300		125112248			CERAMIC CAP./SAFETY 0.0022µF	1220621
0.301	STACKED FILM CAP. 0.220E/50V J	12582245		C 503 🛧	CERAMIC CAP /SAFETY E M	CCG2HMP0E222
C 302		126F226S			2200pF/AC125V or
C 303	CHIP CERAMIC CAP SI J 10pF/50V	CHE1JJBSL100			CERAMIC CAP./SAFETY 0.0022µF	1220621
C 304	CHIP CERAMIC CAP. SL J 820F/50V	CHE1JJBSL820		C 504 🛧	CERAMIC CAP./SAFETY E M	CCG2HMP0E222
C 305	CHIP CERAMIC CAP. SL J 22pF/50V	CHE1JJBSL220			2200pF/AC125V or
C 306	CHIP CERAMIC CAP. F Z 0.01µF/50V	CHE1JZB0F103			CERAMIC CAP./SAFETY 0.0022µF	1220621
C 307	CHIP CERAMIC CAP. SL J 75pF/50V	CHE1JJBSL750		C 505 🛆	METALIZED FILM CAP. 0.1µF/250V or	1220971
C 308	SEMICONDUCTOR CAP. F Z 0.1µF/25V	1220520S			METALIZED FILM CAP. 0.1µF/250V or	1222181
C 309	CHIP CERAMIC CAP. SL J 27pF/50V	CHE1JJBSL270			LINE ACROSS CAP. 0.1µF/250V	6222631
C 310	CHIP CERAMIC CAP. SL J 120pF/50V	CHE1JJBSL121		C 506		CA2HISINCUIS
C.311	ELECTROLYTIC CAP. 1µF/50V M	126F105S		C 507	MYLAB CAP 0.039uE/50V K	22503935
C 313	CHIP CERAMIC CAP. B K 0.0056µF/50V	CHE1JKB0B562		C 508	CERAMIC CAP 0.01upE/2KV or	CCD3DZP0E103
C 314	CHIP CERAMIC CAP. SL J 220pF/50V	CHE1JJBSL221			CERAMIC CAP. 0.01µE/2KV	6220602
C 315	CHIP CERAMIC CAP. FZ 0.01µF/50V	CHE1JZB0F103		C 511	MYLAB CAP 0 0082µF/50V K	22508225
C 316	CHIP CERAMIC CAP. SL J 100pF/50V	CHE1JJBSL101		C 512 A	CERAMIC CAP. 2200pF/400V(T4KV) or	CCN2HMP0E222
C 317	SEMICONDUCTOR CAP. FZ 0.1µF/25V	1220520S			CERAMIC CAP. 0.0022µF/4KV	122Z011
C 318	CHIP CERAMIC CAP. SL J 22pF/50V	CHE1JJBSL220		C 514	MYLAR CAP. 0.0022µF/50V K	2250222S
C 319	CHIP CERAMIC CAP. SL J 75pF/50V	CHE1JJBSL750		C 515	ELECTROLYTIC CAP. 220µF/25V M or	CE1EMZDDL221
C 320	SEMICONDUCTOR CAP. FZ 0.1µF/25V	1220520S			ELECTROLYTIC CAP. 220µF/25V M or	CE1EMZNTL221
C 321	CHIP CERAMIC CAP. SL J 120pF/50V	CHE1JJBSL121			ELECTROLYTIC CAP. 220µF/25V M W/F	626D227
C 322		12604/65		C 516	ELECTROLYTIC CAP. 220µF/6.3V M	126A227S
C 340		10002JKSSL4/1		C 517	CERAMIC CAP. 330pF/1KV or	CCD3AKP0B331
0 341		12034/15		\|	CERAMIC CAP. 330pF/1KV	6220572
0 342		CA2C101NC000		C 518	MYLAR CAP. 0.068µF/50V K	2250683S
0 343	100uF/160V M(105°C) or	0000		C 519	MYLAR CAP. 0.1µF/400V	CT2H104NC001
	ELECTROLYTIC CAP. 100µF/160V M(105°C)	CE2CMZDEH101			MYLAR CAP. 0.1µF/400V	CMA2HKD00104
1			J

Ref. No.	Description	Part No.
520	METALIZED FILM CAP. 0.1µF/250V or	1220971	D
	METALIZED FILM CAP. 0.1µF/250V or	122Z181	D
	LINE ACROSS CAP. 0.1µF/250V	622Z631	D
5. 521	MYLAR CAP. 0.0022µF/50V K	2250222S
	CONNECTORS	·	D
N 201	STRAIGHT PIN HEADER	1740764
CN 202	PIN HEADER 5P (for D.Y) or	1730812	D
	PIN HEADER 5P (for D.Y)	1780168
CN 203		XW01D03NF001	D
	WIRE HOLDER 3P	XW01B03NF001
CN 204	WIRE HOLDER 6P or	XW01D06NF001
	WIRE HOLDER 6P	XW01B06NF001	D
CN 501	PIN HEADER 2P (for D.G COIL) or	1780276
	PIN HEADER 2P (for D.G COIL)	1780165	D
	DIODES
) 202	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T	D
204	SWITCHING DIODE 1SS133 or	1SS133T	D
	DIODE 1SS176TPA7	1SS176T	D
207	SWITCHING DIODE 1SS133 or	1SS133T	D
	DIODE 1SS176TPA7	1SS176T	D
211	ZENNER DIODE MTZ7 5B-T77 or	MTZ7 5BT
	ZENER DIODE GZSZ 5Y-BT or	ODTY00GZS7B5	D
	ZENER DIODE UZ-7 5BSA	ODTA0UZ7R5BS	D
) 212	ZENNEB DIODE MTZZ 5B-TZZ or	MTZ7 5BT
	ZENER DIODE GZSZ 5Y-BT or	ODTY00GZS7B5	D
	ZENER DIODE UZ-7.5BSA	QDTA0UZ7R5BS
) 213	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T	D
214	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T	D
215	SWITCHING DIODE 1SS133 or	1SS133T	D
	DIODE 1SS176TPA7	1SS176T	D
216	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T	D
217	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
218	SWITCHING DIODE 1SS133 or	1SS133T	IC
	DIODE 1SS176TPA7	1SS176T	IC
221	LED SLR-55VC3F(RED) or	1401273	IC
	LED KLR-133L	NP9Z0KLR133L
222	ZENNER DIODE MTZ5.1C or	MTZ5.1CT	IC
	ZENER DIODE GZS5.1Z-BT or	QDTZ00GZS5R1	IC
	ZENER DIODE UZ-5.1BSB	QDTB0UZ5R1BS	IC
) 227	RECTIFIER DIODE ERA15-02KFRB	QDNZ0ERA1502	IC
228	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
229	DIODE ERB12-02L3	AERB1202L300
230	FAST RECOVERY DIODE ERB44-04L3	QDQZ0ERB4404	IC
231	DIODE 1SS130	1SS130T	IC
232	ZENNER DIODE MTZ18BT or	MTZ18BT	IC
	ZENNER DIODE GZS18Y-BT or	QDTY000GZS18
	ZENER DIODE UZ-18BSB	QDTB00UZ18BS
233	ZENNER DIODE MTZ12B or	MTZ12BT	L
	ZENNER DIODE GZS12Y-BT or	QDTY000GZS12
	ZENER DIODE UZ-12BSA	QDTA00UZ12BS	L
234	ZENNER DIODE MTZ5.6B or	MTZ5.6BT
	ZENER DIODE GZS5.6Y-BT or	QDTY00GZS5R6	L
	ZENER DIODE UZ-5.6BSA	QDTA0UZ5R6BS	L
242	FAST RECOVERY DIODE ERD38-06L	AERD3806L000

	r=
Ref. No.		Part No.
D 243	RECTIFIER DIODE ERA22-02KFRB	QDSZ0ERA2202
D 244	FAST RECOVERY DIODE ERB44-02L3	QCDZERB4402L
D 245	RECTIFIER DIODE R2M LF-B1 or	QDDZ00000R2M
	ZENER DIODE EQB01-150	AEQB01150000
D 248	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
D 249	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
D 251	ZENNER DIODE MTZ6.8B or	MTZ6.8BT
	ZENER DIODE GZS6.8Y-BT or	QDTY00GZS6R8
	ZENER DIODE UZ-6 8BSA	ODTA0UZ6B8BS
D 252	SWITCHING DIODE 1SS133 or	155133T
0 202		155176T
D 254		MT78 2BT
0 234		007200078000

	DEOTIFIED DIODE DE EDODA 401 0	QUTAUUZ8H2BS
D 501	RECTIFIER DIODE ERC04-10L3	ODDZUERCO410
D 502	RECTIFIER DIODE ERC04-10L3	ODDZ0ERC0410
D 503	RECTIFIER DIODE ERC04-10L3	ODDZ0ERC0410
D 504	RECTIFIER DIODE ERC04-10L3	QDDZ0ERC0410
D 505	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
D 508	ZENNER DIODE MTZ7.5B-T77	MTZ7.5BT
D 509	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
D 510	ZENNER DIODE MTZ15B-T77 or	MTZ15BT
	ZENNER DIODE GZS15Y-BT or	QDTY000GZS15
	ZENER DIODE UZ-15BSA	QDTA00UZ15BS
D 511	SWITCHING DIODE 1SS133 or	1SS133T
	DIODE 1SS176TPA7	1SS176T
D 512		AEBB44101300
D 513		AERB44101300
D 514	SWITCHING DIODE 188133 or	199122T
0 314		1001001
	DIODE 1331/61PA/	1001007
0 515	SWITCHING DIODE 155133 or	1551331
	DIODE 1551/61PA/	1551/61

IC 201	IC:MICON IMP4/C434N-R214	QSMQA0ZIS015
IC 202	IC TC89101P	GTC89101P***
IC 203
	IC TC4053BP or	14DW168
	IC 1C4053BP or IC BU4053B	14DW168 14LF166
IC 204	IC IC4053BP or IC BU4053B IC LA7830	14DW168 14LF166 14LQ163
IC 204 IC 205	IC IC4053BP or IC BU4053B IC LA7830 IC AN5265	14DW168 14LF166 14LQ163 14LN160
IC 204 IC 205 IC 206	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS	14DW168 14LF166 14LQ163 14LN160 QSBLA0SSN019
IC 204 IC 205 IC 206 IC 207	IC IC4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or	14DW168 14LF166 14LQ163 14LN160 QSBLA0SSN019 14L0242
IC 204 IC 205 IC 206 IC 207	IC IC4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or	14DW168 14LF166 14LQ163 14LN160 QSBLAOSSN019 14L0242 AN78M12
IC 204 IC 205 IC 206 IC 207	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or	14DW168 14LF166 14LQ163 14LN160 QSBLAOSSN019 14L0242 AN78M12 UPC78M12HF
IC 204 IC 205 IC 206 IC 207	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12	14DW168 14LF166 14LQ163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12
IC 204 IC 205 IC 206 IC 207	IC 1G4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC 15631	14DW168 14LF166 14LQ163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631
IC 204 IC 205 IC 206 IC 207 IC 208 IC 208	IC 1G4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011
IC 204 IC 205 IC 206 IC 207 IC 208 IC 208 IC 209 IC 210	IC 1G4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC VOLTAGE REGULATOR, AN78M09 or	14DW168 14LF166 14LO163 14LN160 OSBLAOSSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLAOSSN011 AN78M00
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210	IC 1G4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09
IC 204 IC 205 IC 206 IC 207 IC 208 IC 208 IC 209 IC 210	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39µH-J-26T or	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L78M09
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210	IC 1C4053BP or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39μH-J-26T or INDUCTOR 39μHJ	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L78M09 L1AXJATTU390 2161390T
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210 L 204 L 208	IC 1C40538P or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH(J) MICRO INDUCTOR 47µH-K-AXT or	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L78M09 LLAXJATTU390 2161390T 2165470T
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210 L 204 L 208	IC 1C40538P or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 47µH-K-AXT or MICRO INDUCTOR 47µH-K-5FT	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L78M09 L1AXJATTU390 2161390T 2165470T 2162470T
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210 L 204 L 208 L 209	IC 1C40538P or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 47µH-K-AXT or MICRO INDUCTOR 47µH-K-5FT DELAY LINE	14DW168 14LF166 14LO163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L78M09 L1AXJATTU390 2161390T 2165470T 2162470T 113N852
IC 204 IC 205 IC 206 IC 207 IC 208 IC 209 IC 210 L 204 L 208 L 209 L 209 L 210	IC 1C40538P or IC BU4053B IC LA7830 IC AN5265 IC CXA1213BS VOLTAGE REGULATOR IC NJM78M12FA or IC AN78M12 or IC 78M12 or IC 78M12 IC L5631 IC CXA1214P IC:VOLTAGE REGULATOR AN78M09 or IC 78M09 COILS INDUCTOR 39µH-J-26T or INDUCTOR 39µH-J-26T or INDUCTOR 39µH(J) MICRO INDUCTOR 47µH-K-AXT or MICRO INDUCTOR 47µH-K-5FT DELAY LINE CASING COIL (PAL) or	14DW168 14LF166 14LQ163 14LN160 QSBLA0SSN019 14L0242 AN78M12 UPC78M12HF L78M12 L5631 QSBLA0SSN011 AN78M09 L78M09 L1AXJATTU390 2161390T 2165470T 2162470T 113N852 LFA07V0MM011

12-2

L7483EL

126A227S CCD3AKP0B331 6220572 2250683S CT2H104NC001 CMA2HKD00104

Part No. CE1EMZZTL332

12-3

L7483EL

Page 18

Ref. No.	Description	Part No.	Ref. No.
L 211	CASING COIL (B-Y) or	LFA07V0MM004		TRANSISTO
	CASING COIL (B-Y)	LFA07V0TK010		TRANSISTO
L 212	CASING COIL (R-Y) or	LFA07V0MM004	Q 215	TRANSISTO
	CASING COIL (R-Y)	LFA07V0TK010		TRANSISTO
L 213	MICRO INDUCTOR 10µH or	2165100T		TRANSISTO
	MICRO INDUCTOR 10µH	2162100T		TRANSISTO
L 214	MICRO INDUCTOR 33µH-K-AXT or	2165330T	Q 216	TRANSISTO
	MICRO INDUCTOR 33µH-K-5FT	2162330T		TRANSISTO
L 215	MICRO INDUCTOR 15µH-K-AXT or	2165150T		TRANSISTO
	MICRO INDUCTOR 15µH-K-AXT	2162150T		TRANSISTO
L 216	CASING COIL (BELL) or	LFA07V0MM003	Q 217	TRANSISTO
	CASING COIL (BELL)	LFA07V0TK009		TRANSISTO
L 217	MICRO INDUCTOR 15µH-K-AXT or	2165150T		TRANSISTO
	MICRO INDUCTOR 15µH-K-AXT	2162150T		TRANSISTO
L 218	POT COIL 47µH K	LLBD**DMM001	Q 218	TRANSIST
L 501 🛧	LINE FILTER 2.5mH or	LLBG00ZBW007		TRANSIST
	LINE FILTER 2.5mH or	LLBG00ZMS008		TRANSIST
	LINE FILTER 2.5mH	1812745		TRANSIST
L 503 🛧	LINE FILTER 2.5mH or	LLBG00ZBW007	Q 219	TRANSIST
	LINE FILTER 2.5mH or	LLBG00ZMS008		TRANSIST
	LINE FILTER 2.5mH	1812745	Q 220	TRANSIST
	TRANSISTORS		Q 221	TRANSIST
Q 204	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA		TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199	Q 222	TRANSIST
Q 205	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA		TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199	Q 223	TRANSIST
Q 206	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA		TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199	Q 224	TRANSIST
Q 207	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA		TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199	Q 225	TRANSIST
Q 208	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA		TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199	Q 227	TRANSIST
Q 209	TRANSISTOR 2SA1318T or	2SA1318T		TRANSIST
	TRANSISTOR 2SA1318U or	2SA1318U		TRANSIST
	TRANSISTOR KTA1266GR TO-92 or	NQS40KTA1266		TRANSIST
	TRANSISTOR KTA1267GR	NQS10KTA1267	Q 228	TRANSIST
Q 210	TRANSISTOR 2SA1318T or	2SA1318T		TRANSIST
	TRANSISTOR 2SA1318U or	2SA1318U		TRANSIST
	TRANSISTOR KTA1266GR TO-92 or	NQS40KTA1266		TRANSIST
	TRANSISTOR KTA1267GR	NQS10KTA1267	Q 229	TRANSIST
Q 211	TRANSISTOR 2SA1318T or	2SA1318T		TRANSIST
	TRANSISTOR 2SA1318U or	2SA1318U		TRANSIST
	TRANSISTOR KTA1266GR TO-92 or	NQS40KTA1266		TRANSIST
	TRANSISTOR KTA1267GR	NQS10KTA1267	Q 233	TRANSIST
Q 213	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA		TRANSIST
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	Q 234	TRANSIST
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198		TRANSIST
	TRANSISTOR KTC3199GR	NQS10KTC3199		TRANSIST
		OCCODENTIDAA		TDANCIOT
Q 214	TRANSISTOR 2SC3331(1) or	USU333TINPAA		TRANSIST


o .		Description	Part No.
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	25A1318T or	2541318T
	TRANSISTOR		20410101
	TRANSISTOR	25A1318U or	25A13180
	TRANSISTOR	KTA1266GR TO-92 or	NQS40KTA1266
	TRANSISTOR	KTA1267GR	NQS10KTA1267
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	OSC3331UNPAA
	TRANSISTOR	KTC2109CP TO 02 or	NOS40KTC3108
	TRANSISTOR	KT001000D	NQ340KT00190
	TRANSISTOR	KTC3199GH	NUSTURICITI
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	2SC3331(T) or	OSC3331TNPAA
	TRANSICTOR		OCCODENTIALING
	TRANSISTOR	25C3331(U) or	USC333TUNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	2SC2271(D) or	2SC2271D
	TRANSISTOR	2SC2271(E)	2SC2271E
	TRANSISTOR	2SD23311.S	00PZ02SD2331
	TDANEIETOD	2541318T or	25A1310T
	TRANSISTOR	23A13181 0	23413101
	THANSISTOR	25A1318U 0F	25A1318U
	TRANSISTOR	K1A1266GR TO-92 or	NQ540KTA1266
	TRANSISTOR	KTA1267GR	NQS10KTA1267
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GB	NOS10KTC3199
	TRANSISTOR	2SC2221(T) or	OSC3331TNPAA
	TRANSISTOR
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40K1C3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GB	NOS10KTC3199
	TRANSISTOR	25C2221(T) or	OSC2221TNIDAA
	TRANSISTOR
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	IRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NOS40KTC3198
	TDANEIETOD	KTC3100GP	NOSIOKTO2100
	TOMOSIOTO		1102106103133
	THANSISTOR	2503331(1) or	USU3331 INPAA
	TRANSISTOR	2SC3331(U) or	USC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NQS10KTC3199
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOP	KTC3198GR TO-92 or	NOS40KTC3198
	TDANCIETOD	KTC3100GP	NOSIOKTOSIO
	TRANSISTUR		0000107100199
	THANSISTER	2581274(H) or	U25B12/4H000
	TRANSISTER	2SB1274(S)	Q2SB1274S000
	TRANSISTOR	2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR	2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR	KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR	KTC3199GR	NOS10KTC3199
	TRANSISTOR	2SC3331/T) or	OSC3331TNDAA
			LOUGOLINEAA
			L7483EL

Ref. No.	Description	Part No.	Ref.	No.	Description	Part No.
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 239		CHIP RES. 1/10W J 15KΩ	RRXAJBBZ0153
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198	R 240		CHIP RES. 1/10W J 22KΩ	RRXAJBBZ0223
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 241		CHIP RES. 1/10W J 27KΩ	RRXAJBBZ0273
0.236	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA	R 244		CHIP RES. 1/10W J 68KΩ	RRXAJBBZ0683
G 100	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 245		CHIP RES. 1/10W J 390Ω	RRXAJBBZ0391
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198	R 246	;	CHIP RES. 1/10W J 1KQ	RRXAJBBZ0102
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 247	,	CHIP RES. 1/10W J 5.6KΩ	RRXAJBBZ0562
0 237	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA	R 248		CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
Q 20,	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 249		CARBON RES. 1/6W J 150Ω or	132A151T
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198			CARBON RES. 1/5W J 150Ω	1324151T
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 250	)	CARBON RES. 1/6W J 2.2KΩ or	132A222T
0 239	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA			CARBON RES. 1/5W J 2.2KΩ	1324222T
4 200	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 251		CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198	R 252	2	CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 253	3	CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
0 240	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA	R 254		CHIP RES. 1/10W J 1.5KΩ	RRXAJBBZ0152
G 240	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 260	)	CARBON RES. 1/6W J 330Ω or	132A331T
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198			CARBON RES. 1/5W J 330Ω	1324331T
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 262	2	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103
0 501	FET 2SK2039	QF4Z02SK2039	R 263	3	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103
0 503	TRANSISTOR 2SC3331(T) or	OSC3331TNPAA	R 264	1	CHIP RES. 1/10W J 33KΩ	RRXAJBBZ0333
0.000	TRANSISTOR 2SC3331(U) or	OSC3331UNPAA	R 265	5	CHIP RES. 1/10W J 2.7KΩ	RRXAJBBZ0272
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198	R 266	5	CHIP RES. 1/10W J 12KΩ	RRXAJBBZ0123
	TRANSISTOR KTC3199GB	NOS10KTC3199	R 267	7	CHIP RES. 1/10W J 5.6KΩ	RRXAJBBZ0562
0 504	TRANSISTOR 2SB698(E) or	OOSE002SB698	B 268	3	CHIP RES 1/10W J 1 8KQ	RRXAJBBZ0182
4 004	TRANSISTOR 2SB698(G)	00SG002SB698	B 269	- 3	CHIP RES. 1/10W J 2 7KΩ	RRXAJBBZ0272
0 505 🛧	PHOTO COUPLER PC111LYS	OPES0PC111LY	R 270	)	CHIP RES. 1/10W J 18KQ	RRXAJBBZ0183
0.506	FET 2SK212E or	2SK212E	R 271		CHIP RES. 1/10W J 22KQ	RRXAJBBZ0223
	FET 2SK212E	2SK212F	R 272	2	CHIP RES. 1/10W J 8.2KΩ	RRXAJBBZ0822
Q 507	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA	R 273	3	CHIP RES. 1/10W J 68KΩ	RRXAJBBZ0683
u,	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA	R 274	1	CHIP RES. 1/10W J 3.9KΩ	RRXAJBBZ0392
	TBANSISTOR KTC3198GB TO-92 or	NOS40KTC3198	R 275	5	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103
	TRANSISTOR KTC3199GR	NQS10KTC3199	R 276	6	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103
	BESISTORS		R 27	7	CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
B 204	CHIP BES 1/10W J 6 8KO	BBXAJBBZ0682	R 278	3	CARBON RES. 1/6W J 10KΩ or	132A103T
B 205	CHIP BES 1/10W J 5 6KQ	BBXAJBBZ0562		-	CABBON BES 1/5W J 10KQ	1324103T
B 207	CHIP BES 1/10W J 10KO	BBXAJBBZ0103	R 279	9	CHIP RES. 1/10W J 47KQ	RRXAJBBZ0473
R 214	CHIP BES 1/10W J 12KQ	BBXAJBBZ0123	R 280	5	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103
B 215	CHIP BES 1/10W J 12KO	BBXAJBBZ0123	R 28	1	CHIP RES. 1/10W J 82KΩ	RRXAJBBZ0823
R 216	CABBON BES 1/6W J 10KO or	132A103T	R 282	2	CHIP RES. 1/10W J 56KΩ	RRXAJBBZ0563
	CABBON BES 1/5W J 10KO	1324103T	B 28	3	CHIP RES 1/10W J 33KO	BBXAJBBZ0333
R 217	CARBON RES. 1/6W J 10KO or	132A103T	B 284	1	CHIP RES 1/10W J 4700	BBXAJBBZ0471
	CABBON BES 1/5W J 10KO	1324103T	B 28	5	CHIP BES 1/10W J 1KQ	BBXAJBBZ0102
B 220	CHIP BES 1/10W J 5 6KO	BBXA IBBZ0562	B 286	5	CHIP RES 1/10W J 15KQ	RRXAJBBZ0153
B 221	CHIP BES 1/10W J 3 9KO	BBXA IBBZ0392	R 28	7	CHIP RES 1/10W J 68KQ	RRXAJBBZ0683
R 222	CHIP BES 1/10W J 12KO	BBXA BB70123	B 28	8	CHIP RES 1/10W J 68KO	BBXAJBBZ0683
R 223	CHIP BES 1/10W J 12KO	BBXA BBZ0123	R 289	- 9	CHIP BES 1/10W J 12KO	BBXAJBBZ0123
R 224	CHIP RES 1/10W L68KO	RBXA IBBZ0683	R 290	r n	CHIP BES 1/10W J 12KO	BRXAJBBZ0123
R 225	CHIP RES 1/10W 14 7KO	BBYA IBB70472	R 29	1	CABBON BES 1/4W J 10 or	13451095
R 226	CHIP RES 1/10W 13 0KO	RRYA IBB70302	11 20	•	CABBON BES 1/4W J 10	BCX4.14T70109
R 227	CHIP RES 1/10W 133KO	REXA IBEZ0333	B 29	2	CABBON BES 1/4W J 2 20 or	13452295
R 228	CHIP RES 1/10W 12 2KO	RBXA IBB70222	11 201	-	CABBON BES 1/4W J 2 20	BCX41AT70229
R 231			B 204	â	CARBON RES 1/4W L1KO or	13451025
R 232		RRXA IRR70/72	1 290		CABBON BES 1/4W J 1KO	BCX414T70102
R 233			D 200	R	CHIP RES 1/10W 14 7KO	RRYA IRR70472
R 234			D 290	1	CHIP RES. 1/10W 110KO	RRYA IRR70102
R 235	CHIP RES. 1/10W J ISKS2		00 1	' ว	CHID DES 1/10W 119KO	DDYA IPD70100
R 226			000	- 3	CHID DES 1/10W LIOKO	DRYA IRDZO103
R 237	CHIP DES 1/10W L22KO			4	CHID DES 1/10W LEGOD	DRYA IRRACE
R 239	CHID DES 1/10W 115KO		000	, 5	CHIP RES 1/10W 14 70	BBYA IBB704D7
.1 200	UNIE DES. 1/1011 J 13R52		n 30		101111 DEO. 1/1044 0 4.752

12-5

Page 19

Ref. No.	Description	Part No.	Ref. No.	Description	Part No.		Ref No	Description	Part No.	Г
R 306	CARBON RES. 1/4W J 220Ω or	1345221S	R 365	CHIP RES. 1/10W J 270Ω	RRXAJBBZ0271		nei. No.	CARBON BES 1/5W 110KO
	CARBON RES. 1/4W J 220Ω	RCX4JATZ0221	R 366	CHIP RES. 1/10W J 470Ω	RRXAJBBZ0471		0.01	CEMENT RES. 5W K 1 20 or	BW051B2BC001
307	FUSE RES. 2.2Ω 1W or	RF01229KA004	R 367	CHIP RES. 1/10W J 2.2KΩ	RRXAJBBZ0222		H 501	CEMENT RES. SW K 1.20 or	DW051D2F0001
	FUSE RES. 1W J 2.2Ω	5363229	R 368	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103			CEMENT RES. 5W K 1.20	DW051D2KA006
308	FUSE RES. 2.2Ω 1W or	RF01229KA004	R 369	CHIP RES. 1/10W J 22KΩ	RRXAJBBZ0223			CARRON RES. 1/4W L10MO or	12451069
	FUSE RES. 1W J 2.2Ω	5363229	R 396	CARBON RES. 1/6W J 150KΩ or	132A154T		R 502	CARBON RES. 1/4W J 10MS2 0	13451005 DCV4 IAT70106
310	CARBON RES. 1/6W J 5.6KΩ or	132A562T		CARBON RES. 1/5W J 150KΩ	1324154T			CARBON RES. 1/4W J TOMSZ	10450050
	CARBON RES. 1/5W J 5.6KΩ	1324562T	R 398	CARBON RES. 1/6W J 33KΩ or	132A333T		R 503	CARBON RES. 1/4W J 3.9MS2 0	13433935
311	CABBON BES 1/6W J 5.6KQ or	132A562T		CARBON RES. 1/5W J 33KΩ	1324333T			CARBON RES. 1/4W J 3.9MSZ	HCX4JATZUTZ4
	CARBON BES 1/5W J 5.6KΩ	1324562T	R 399	CARBON RES. 1/4W J 1.5KΩ or	1345152S		R 504	CARBON RES. 1/4W J 15KS2 or	13451535
314	CHIP BES 1/10W J 820Q	RRXAJBBZ0821		CARBON RES. 1/4W J 1.5KΩ	RCX4JATZ0152			CARBON RES. 1/4W J 15KS2	HCX4JA120153
3 315	CABBON BES 1/4W J 2 2KQ or	1345222S	R 400	CARBON RES. 1/6W J 22KΩ or	132A223T		R 505	CARBON RES. 1/4W J 27052 OF	13452715
	CABBON BES 1/4W J 2 2KQ	RCX4JATZ0222		CARBON RES. 1/5W J 22KΩ	1324223T			CARBON RES. 1/4W J 22052	RCX4JA1Z0221	-
316	CEMENT BES 5W K 3 3KO or	RW05332PG003	R 401	CARBON RES. 1/6W J 27KΩ or	132A273T		R 508	METAL RES. 3W J 33RS2 or	RN03333RE003	5
	CEMENT RES 33KO 5W or	RW05332UB001		CARBON RES. 1/5W J 27KΩ	1324273T			METAL RES. 3W J 33KS2 or	RN0302020333
	CEMENT RES. 5W K 3 3KO	RW05332KA006	R 402	CARBON RES. 1/4W J 1.5KΩ or	1345152S				RN03333KA001	S
317	CHIP BES 1/10W J 82KO	BBXAJBBZ0823		CARBON RES. 1/4W J 1.5KΩ	RCX4JATZ0152		R 512	SEMENT RES. 2W J 0.5622 or	RW03R56PG005
2 318	CARBON RES 1/6W 112KO or	132A123T	B 403	CARBON RES. 1/6W J 5.6KΩ or	132A562T			SEMENT RES. 2W J 0.562	HWU3H56KAU12	l s
1 510	CARBON RES. 1/5W J 12KO	1324123T		CARBON RES. 1/5W J 5.6KΩ	1324562T		R 513	CARBON RES. 1/4W J 680Ω or	13456815
210	CHIP RES 1/10W \| 12KO	BBXAJBBZ0123	R 404	CARBON RES. 1/6W J 100KΩ or	132A104T			CARBON RES. 1/4W J 680Ω	RCX4JA1Z0681	\| S
2	CHIP RES. 1/10W 1100KO	BBXA BBZ0104		CABBON BES 1/5W J 100KΩ	1324104T		R 406	CARBON RES. 1/6W J 2.2KΩ or	132A222T	1
- 320 - 221	CARBON RES. 1/6W \| 220KO or	132A224T	B 405	CABBON BES 1/6W J 120KΩ or	132A124T			CARBON RES. 1/5W J 2.2KΩ	1324222T	S
1 321	CARBON RES. 1/5W J 220KO	1324224T	11 400	CABBON BES 1/5W J 120KO	1324124T		R 517	CARBON RES. 1/6W J 1.2MΩ or	132A125T
	CURDES 1/10W L1 9KO	DDYA IBB70182	B 406	CABBON BES 1/6W 122KO or	132A222T			CARBON RES. 1/5W J 1.2MΩ	1324125T	s
H 322			n 400	CARBON RES 1/5W 122KO	1324222T		R 518	CARBON RES. 1/6W J 1MΩ or	132A105T
H 323			B 407	CARBON RES. 1/6W J 22KO or	132A223T			CARBON RES. 1/5W J 1MΩ	1324105T	s
1 324	CHIP RES. 1/10W J 10KS2	DDVA IPP70152	n 407	CARBON BES 1/5W J 22KO	1324223T		R 519	CARBON RES. 1/6W J 330Ω or	132A331T
4 325			D 409	METAL BES 1W 115KO or	BN01.JZDZ0153			CARBON RES. 1/5W J 330Ω	1324331T	s
4 326	CHIP RES. 1/10W J 1.8KS2		h 400	METAL RES. 1W 115KO	534 4153		R 520	CARBON RES. 1/6W J 150KΩ or	132A154T
4 327	CHIP RES. 1/10W J 100KS2		B 410	CAPBON RES 1/6W 11800 or	132A181T			CARBON RES. 1/5W J 150KΩ	1324154T	s
4 328	CHIP RES. 1/10W J 100KS2		n 410	CARBON RES 1/5W 11800	1324181T		R 521	CARBON RES. 1/6W J 10KΩ or	132A103T	\| \|
4 329	CHIP RES. 1/10W J 6.8KS2		D 411	CHIP PES 1/10W 12 7KO	BBXA IBB70272		1	CARBON RES. 1/5W J 10KΩ	1324103T	1
8 330			D 411	METAL RES 2W 1270 or	BN02.17D70270		R 522	CARBON RES. 1/6W J 1KΩ or	132A102T
H 331	CHIP RES. 1/10W J 10KS2		n 412	METAL RES. 2W 1270	534B270			CARBON RES. 1/5W J 1KΩ	1324102T	s
4 332			D 412	CHIP PES 1/10W L69KO	BBXA IBB70683		R 523	CARBON RES. 1/6W J 330Ω or	132A331T
H 333	CHIP RES. 1/10W J 680KS2		D 413		RBYA IBB70273			CARBON RES. 1/5W J 330Ω	1324331T	Т
4-335			R 414	CARRON RES. 1/6W 110KO or	132A103T		R 524	CARBON RES. 1/6W J 270Ω or	132A271T
H 336			H 415	CARBON RES. 1/6W J 10KS2 0	1324103T			CARBON RES. 1/5W J 270Ω	1324271T	T T
R 337	CHIP RES. 1/10W J 4./KS2		D 410	CARBON RES. 1/5W J 10KSZ	13241001 1324332T		R 525	CARBON RES. 1/6W J 330Ω or	132A331T	Т
H 338	CHIP RES. 1/10W J 4/0Ω	RRXAJBBZ0471	H 416	CARBON RES. 1/6W 13.5KS2 0	102A0021			CARBON RES. 1/5W J 330Ω	1324331T
R 339	CHIP RES. 1/10W J 330KΩ	RHXAJBBZ0334	D 117	CARBON RES. 1/5W J 3.3KS2	DDV A IDD70101		R 530	CARBON RES. 1/4W J 560K or	134556S	V V
R 340	CHIP RES. 1/10W J 330Ω	RRXAJBBZ0331	R 417	CHIP RES. 1/10W J 10052	RRXAJBBZUIUI			CARBON RES. 1/4W J 560KΩ	RCX4JATZ0564	l V
R 341	CHIP RES. 1/10W J 5.6KΩ	RRXAJBBZ0562	R 418	FUSE RES. 1/2W J 2.252 or	5362229		JW 202	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	l lv
R 346	METALIZED FILM RES. 1/5W F 27KΩ	13C2/02		FUSE RES. 1/2W J 2.252	536/229		JW 203	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	l V
R 347	CHIP RES. 1/10W J 4.7KΩ	RRXAJBBZ0472	R 430	CHIP RES. 1/10W J 2.2KS	RRXAJBBZ0222		JW 204	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	\| \|-
R 348	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103	R 431	CHIP RES. 1/10W J 10KΩ	RHXAJBBZ0103		JW 205	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
R 349	CHIP RES. 1/10W J 27KΩ	RRXAJBBZ0273	R 433	CHIP RES. 1/10W J 180Ω	RRXAJBBZ0181		JW 206	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	E
R 350	CHIP RES. 1/10W J 3.3MΩ	RRXAJBBZ0335	R 434	CHIP RES. 1/10W J 3.3KΩ	RRXAJBBZ0332		JW 207	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	l le
R 351	CHIP RES. 1/10W J 390Ω	RRXAJBBZ0391	R 435	CHIP RES. 1/10W J 4.7KΩ	RHXAJBBZ04/2		JW 208	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
R 355	CHIP RES. 1/10W J 47KΩ	RRXAJBBZ0473	R 436	CHIP RES. 1/10W J 100KΩ	RRXAJBBZ0104		JW 210	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
R 356	CARBON RES. 1/6W J 470Ω or	132A471T	R 437	CHIP RES. 1/10W J 100KΩ	RRXAJBBZ0104		JW 211	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
	CARBON RES. 1/5W J 470Ω	1324471T	R 440	CHIP RES. 1/10W J 3.3KΩ	RRXAJBBZ0332		JW 213	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	I F
R 357	CHIP RES. 1/10W J 390Ω	RRXAJBBZ0391	R 441	CARBON RES. 1/6W J 47Ω or	132A470T		JW 214	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	l le
R 358	CHIP RES. 1/10W J 820Ω	RRXAJBBZ0821		CARBON RES. 1/5W J 47Ω	1324470T		JW 215	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	i ľ
R 359	CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102	R 442	CARBON RES. 1/6W J 33KΩ or	132A333T		JW 216	CHIP RES. 1/10W J 02	RRXAJBBZ0000	\| \|-
R 360	CARBON RES. 1/6W J 270Ω or	132A271T		CARBON RES. 1/5W J 33KΩ	1324333T		JW 217	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000	i ľ
	CARBON RES. 1/5W J 270Ω	1324271T	R 443	CARBON RES. 1/6W J 33KΩ or	132A333T		JW 218	CHIP RES. 1/10W J 02	RRXAJBBZ0000	i la
R 361	CHIP RES. 1/10W J 390	RRXAJBBZ0391		CARBON RES. 1/5W J 33KΩ	1324333T		JW 220	CHIP RES. 1/10W J 0Ω	BRXA IBBZ0000	1 I."
R 362	CHIP RES. 1/10W J 4.7KΩ	RRXAJBBZ0472	R 446	CARBON RES. 1/6W J 10KΩ or	132A103T		JW 221	CHIP RES. 1/10W J 0Ω	BRXAJBBZ0000
R 363	CHIP RES. 1/10W J 10KΩ	RRXAJBBZ0103		CARBON RES. 1/5W J 10KΩ	1324103T	\| \|	JW 222	CHIP RES. 1/10W J 0Ω	BRXAJBBZ0000
D 004	CHIP DES 1/10W 13000	BBXA BBZ0391	R 447	CARBON RES 1/6W J 10KQ or	132A103T		JW 223	CHIP RES 1/10W LOO		, Ľ

Ref. No.	Description	Part No.
JW 224	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 226	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 227		RRXAJBBZ0000
JW 228		RRXAJBBZ0000
JW 230	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 232		RRXAJBBZ0000
JW 233		RRXAJBBZ0000
JW 234		RRXAJBBZ0000
JW 240		RRXAJBBZ0000
JW 241		RRXAJBBZ0000
JW 250		RRXAJBBZ0000
	SWITCHES	·
SW 201	TACT SWITCH SKHHBV or	SST0101AL013
	LIGHT TOUCH SWITCH EVQPAC07K	SST0101MS013
SW 202	TACT SWITCH SKHHBV or	SST0101AL013
	LIGHT TOUCH SWITCH EVQPAC07K	SST0101MS013
SW 203	TACT SWITCH SKHHBV or	SST0101AL013
	LIGHT TOUCH SWITCH EVQPAC07K	SST0101MS013
SW 204	TACT SWITCH SKHHBV or	SST0101AL013
	LIGHT TOUCH SWITCH EVOPAC07K	SST0101MS013
SW 205		SST0101AI 013
		SST0101MS013
SW 206	TACT SWITCH SKHHBV or	SST0101AI 013
011 200		SST0101MS013
SW 207	TACT SWITCH SKHHBV or	SST0101AL013
011 207		SST0101MS013
SW 208		SST010141013
011 200		SST0101AE013
SW 200		65500000K001
311 209		1621654
		1021004 88800003W/M001
		SSS0202WW001
SW/ 501 A	DICH SWITCH SDDW01 CEE AD	SSS02020202000
2M 201 YZ		SFFUAAZINISUUT
T 201 A		I TEODEDC SOOT
	FLYDACK TRANS 154-064M [GOLD STAI] OF	LIFUEPGSUU
T 000	FLIDAUR TRANS FUR-148025 (SAMSUNG)	LIFUUEPSMUU2
	HURIVE TRANS TE-1410	1150325
	POWER TRANS	LTTO0EPMS012
VD 202		100 170 1
VH 202		138J/84
VH 203		138J//6
VH 204		138J/76
VH 205		\|138J/78
A 0		0514401405
A 3	POWER KNOB	UEM401485
B 3		UEM401473
84 D.C	SENSOR HOLDER	UEM401471
B 5		UEM401374
UL 201	GLASS DELAY EFDEN645A61H or	1813554
	GLASS DELAY	1812056
F 501 🛧	FUSE T4.0AH 250V	PAGC20BAG402
FH 501	HOLDER FUSE FH-V-03078 or	XH01Z00DK001
	HOLDER FUSE CNT41-0014	1790424
FH 502	HOLDER FUSE FH-V-03078 or	XH01Z00DK001
	HOLDER FUSE CNT41-0014	1790424

HS 1	HEAT SINK ASSY (for Q501)	0EMN00553
HS 1 HS 2	HEAT SINK ASSY (for Q501) HEAT SINK PS (for IC204/IC207)	0EMN00553 0EM401145
HS 1 HS 2 IP 201	HEAT SINK ASSY (for Q501) HEAT SINK PS (for IC204/IC207) IC PROTECTOR ICP-N10	0EMN00553 0EM401145 579F085Z

L7483EL

Page 20

Ref. No.	Description	Part No.	R
J 201	EARPHONE JACK HSJ1403-01-010	JYSL030HD002	RE
J 202	RCA JACK JPJ2030-01-030	JXRL010HD001
J 203	BNC JACK or	JXNL010RA002	Re
	BNC JACK	JXNL010HD002
L 1	SCREW B-TIGHT BIND HEAD 3X8	GBMB3080	Re
LD 2	RIBBON WIRE 3P	WX1L7401-003
LD 3	RIBBON WIRE 6P	WX1L7401-004	Re
PS 501	POSISTOR ZPB53BL200C	5790117
TP 1	TEST PIN or	1700093	R
	TEST PIN SJT-743-3	1740354
TP 2	TEST PIN or	1700093	R
	TEST PIN SJT-743-3	1740354
TP 3	TEST PIN or	1700093	R
	TEST PIN SJT-743-3	1740354	R
TP 4	TEST PIN or	1700093	R
	TEST PIN SJT-743-3	1740354	R
TP 5	TEST PIN or	1700093	R
	TEST PIN SJT-743-3	1740354	R
TU 201	TUNER UNIT ENV-79838-F2	UTUNPSDMS001	R
U 201	REMOCOM RECEIVE UNIT CMXX920F-S	USESJRSSN001	R
W 501 🛧	AC CORD LA-1398	WAE0192LW001	R
XT 201	CERALOCK 4.19MHz or	1812885	R
	CERAMIC RESONATOR KBR-4.19MKS	1813682	R
XT 202	SERAMIC RESONATOR CSB500F2	1812039
XT 203	CRYSTAL OSILLATOR 4.43MHz	1811387	R
XT 204	CRYSTAL OSILLATOR 3.579545KHz	1811291
	HEAT SINK SHEET (for q501) or	XJ0Z000DB001	R
	HEAT SINK SHEET (for q501)	XJ0Z000CA002
	LEAD CLAMPER or	1790256	R
	LEAD CLAMPER	1790356	R
			R

CRT PCB (MMA-B)

Ref. No.	Description	Part No.
	CRT PCB (MMA-B)
Consists of the following:
	CAPACITORS
C 601 🛧	CERAMIC CAP. 0.01µF/2KV or	CCD3DZP0E103
	CERAMIC CAP. 0.01µF/2KV	6220602
C 602	CHIP CERAMIC CAP. SL J 270pF/50V	CHE1JJBSL271
C 603	CHIP CERAMIC CAP. SL J 270pF/50V	CHE1JJBSL271
C 604	CHIP CERAMIC CAP. SL J 330pF/50V	CHE1JJBSL331
	CONNECTORS
CN 601	CRT SOCKET HPS1171-01-020 or	1780080
	CRT SOCKET CVT3308-1301	1780218
CN 602	CONNECTOR PIN 1P or	1700576
	CONNECTOR PIN 1P RT-01N-2.3A	1730688
CN 603	WIRE HOLDER 3P 51039-0300 or	XW01D03NF001
	WIRE HOLDER 3P 51039-0300	XW01B03NF001
CN 604	WIRE HOLDER 6P 51039-0600 or	XW01D06NF001
	WIRE HOLDER 6P 51039-0600	XW01B06NF001
	TRANSISTORS
Q 601	TRANSISTOR 2SC2228(D) or	2SC2228D
	TRANSISTOR 2SC2228(E)	2SC2228E
Q 602	TRANSISTOR 2SC2228(D) or	2SC2228D
	TRANSISTOR 2SC2228(E)	2SC2228E
Q 603	TRANSISTOR 2SC2228(D) or	2SC2228D
	TRANSISTOR 2SC2228(E)	2SC2228E
	RESISTORS


Ref. No.	Description	Part No.
R 601	CARBON RES. 1/4W J 1.8KΩ or	RCX4JATZ0182
	CARBON RES. 1/4W J 1.8KΩ	1345182S
R 602	CARBON RES. 1/4W J 1.8KΩ or	RCX4JATZ0182
	CARBON RES. 1/4W J 1.8KΩ	1345182S
R 603	CARBON RES. 1/4W J 1.8KΩ or	RCX4JATZ0182
	CARBON RES. 1/4W J 1.8KΩ	1345182S
R 604	CARBON RES. 1/4W J 1.5KΩ or	RCX4JATZ0152
	CARBON RES. 1/4W J 1.5KΩ	1345152S
R 605	CARBON RES. 1/4W J 1.5KΩ or	RCX4JATZ0152
	CARBON RES. 1/4W J 1.5KΩ	1345152S
R 606	CARBON RES. 1/4W J 1.5KΩ or	RCX4JATZ0152
	CARBON RES. 1/4W J 1.5KΩ	1345152S
R 607	CHIP RES. 1/10W J 2.7KΩ	RRXAJBBZ0272
R 608	CHIP RES. 1/10W J 820Ω	RRXAJBBZ0821
R 609	CHIP RES. 1/10W J 220Ω	RRXAJBBZ0221
R 610	CHIP RES. 1/10W J 2.7KΩ	RRXAJBBZ0272
R 611	CHIP RES. 1/10W J 1.5KΩ	RRXAJBBZ0152
R 612	CHIP RES. 1/10W J 820Ω	RRXAJBBZ0821
R 613	CHIP RES. 1/10W J 220Ω	RRXAJBBZ0221
R 614	CHIP RES. 1/10W J 2.2KΩ	RRXAJBBZ0222
R 615	CHIP RES. 1/10W J 820Ω	RRXAJBBZ0821
R 616	CHIP RES. 1/10W J 220Ω	RRXAJBBZ0221
R 617	METAL RES. 1W J 15KΩ or	RN01JZDZ0153
	METAL RES. 1W J 15KΩ	534A153
R 618	METAL RES. 1W J 15KΩ or	RN01JZDZ0153
	METAL RES. 1W J 15KΩ	534A153
R 619	METAL RES. 1W J 15KΩ or	RN01JZDZ0153
	METAL RES. 1W J 15KΩ	534A153
R 620	CHIP RES. 1/10W J 2.2KΩ	RRXAJBBZ0222
R 621	CHIP RES. 1/10W J 470Ω	RRXAJBBZ0471
R 622	CHIP RES. 1/10W J 2.2KΩ	RRXAJBBZ0222
R 623	CHIP RES. 1/10W J 470Ω	RRXAJBBZ04/1
R 624	CHIP RES. 1/10W J 2.2KΩ	RRXAJBBZ0222
R 625	CHIP RES. 1/10W J 470Ω	RRXAJBBZ04/1
R 626	CHIP RES. 1/10W J 270Ω	RRXAJBBZ02/1
R 627	CHIP RES. 1/10W J 270Ω	RRXAJBBZ02/1
R 628	CHIP RES. 1/10W J 2/0Ω	RHXAJBBZ02/1
JW 601	CHIP RES. 1/10W J 0Ω	RHXAJBB20000
JW 602		RRXAJBBZ0000
JW 603		RRXAJBBZ0000
JW 604	CHIP RES. 1/10W J 02	RRXAJBBZ0000
		100.000
VH 601		138,015
VH 602	POTENTIONETED 2KO D	130,015
	DOTENTIONETED SKOP	130,016
VH 604		138,010
VH 605	POTENTIONETED SKOP	138,016
VH 606	LATENHOMETER 2025	130310


IF PCB
D. ( M.	Description	Dont No.

Description Part N
IF PCB (MMA-C)	\|
Consists of the following:
CAPACITORS
CHIP CERAMIC CAP. SL J 22pF/50V	CHE1JJBSL220
CHIP CERAMIC CAP. SL J 10pF/50V	CHE1JJBSL100
CHIP CERAMIC CAP. B K 0.01µF/50V	CHE1JKB0B103
MYLAR CAP. 0.068µF/50V K	2250683S
	Description IF PCB (MMA-C) Consists of the following: CAPACITORS CHIP CERAMIC CAP. SL J 22pF/50V CHIP CERAMIC CAP. SL J 10pF/50V CHIP CERAMIC CAP. B K 0.01µF/50V CHIP CERAMIC CAP. B K 0.01µF/50V MYLAR CAP. 0.068µF/50V K

Her. NO.	Description	Fait 110
C 105	CHIP CERAMIC CAP. B K 0.001µF/50V CHE1JKB0B102
C 106	ELECTROLYTIC CAP 0.47µF/50V M 126F474S
C 107	ELECTROLYTIC CAP. 4.7µF/50V M 126F475S
C 108	CHIP CERAMIC CAP. F Z 0.01µF/50V	CHE1JZB0F103
C 110	CHIP CERAMIC CAP. F Z 0.01 µE/50V	CHE1JZB0F103
0 110	CHIP CERAMIC CAP E Z 0.01 JE/50V	CHE1.IZB0E103
6 111		CHE1 IZBOE103
C 112	CHIP CERAMIC CAP E Z 0.01µE/50V CHE1JZB0F103
C 113
C 120	CHIP CERAMIC CAP. F Z 0.01µF/50V CHE1JZB0F103
C 121	CHIP CERAMIC CAP. FZ 0.01µF/50V	CHE1JZB0F103
C 122	CHIP CERAMIC CAP. CH J 130pF/50V	CHE1JJBCH131
C 124	CHIP CERAMIC CAP. SL J 27pF/50V	CHE1JJBSL270
C 125	CHIP CERAMIC CAP. SL J 33pF/50V	CHE1JJBSL330
C 126	CHIP CERAMIC CAP. SL J 22pF/50V	CHE1JJBSL220
C 127	CHIP CERAMIC CAP. SL J 27pF/50V	CHE1JJBSL270
C 128	ELECTROLYTIC CAP. 47µF/50V M	126F476S
C 120	CHIP CERAMIC CAP. F Z 0.01 µE/50V	CHE1JZB0F103
0 129	CHIR CERAMIC CAP E 7 0.01 JE/50V	CHE1JZB0E103

		1770090
CN 101	PCB CONNECTOR 6P TXX-P06P-G1	1770000
CN 102	PCB CONNECTOR 3P TXX-P03P-G1 (L TYPE)	1770986
CN 103	CONNECTOR BASE 4P (EH/TOP)	1730628
CN 104	CONNECTOR BASE 3P (EH/TOP)	1730627
	COILS
L 101	MICRO INDUCTOR 1µH or	2165109T
	MICRO INDUCTOR 1µH	2162109T
1 102		2165688T
		2162688T
1 104		2165100T
L 104		2103100T
		21621001
L 105	МІСНО INDUCTOR 10µН or 2165100Т

L 106	CASING COIL	LFA07V0MM001
L 107	107 CASING COIL LFA07VON
	TRANSISTORS
Q 102	TRANSISTOR 2SC3331(T) or	QSC3331TNPAA
	TRANSISTOR 2SC3331(U) or	QSC3331UNPAA
	TRANSISTOR KTC3198GR TO-92 or	NQS40KTC3198
	TRANSISTOR KTC3199GR	NQS10KTC3199
Q 103	TRANSISTOR 2SC3000D or	2SC3000D
	TRANSISTOR 2SC3000F	2SC3000F
0 104	TRANSISTOR 2541219T or	2541318T
	TRANSISTOR 20410101	20010101
	THANSISTUR 25A13180 or	25A1318U
	TRANSISTOR KTA1266GR TO-92 or	NQS40KTA1266
	IRANSISTOR KTA1267(GR)	NQS10KTC1267
	RESISTORS
R 101	CHIP RES. 1/10W J 470Ω	RRXAJBBZ0471
R 102	CHIP RES. 1/10W J 390Ω	RRXAJBBZ0391
R 103	CHIP RES. 1/10W J 470Ω	RRXAJBBZ0471
R 104	CHIP RES. 1/10W J 330Ω RRXAJBB70331
R 105	CHIP RES. 1/10W J 5.6KΩ	RRXAJBBZ0562
R 106	CHIP BES 1/10W J 1 8KO	BRXAJBBZ0182
B 107	CHIP RES 1/10W 1/22KO	BBXA IBB70222
B 100	CHID DEC 1/10W J 22RS2
D 100		RHXAJBBZ0561
0 109	CHIP RES. 1/10W J 10KS2	HHXAJBBZ0103
H 110	CHIP RES. 1/10W J 560Ω	RRXAJBBZ0561
R 111	CHIP RES. 1/10W J 1.5KΩ RRXAJBBZ0152
R 112	CHIP RES. 1/10W J 82KΩ RRXAJBBZ0823
R 113	CHIP RES. 1/10W J 180KΩ RRXAJBBZ0184

Ref. No.	Description Part No.
R 115	CHIP RES. 1/10W J 330Ω RRXAJBBZ03
R 116	CHIP RES. 1/10W J 560Ω RRXAJBBZ0
R 117	CHIP RES. 1/10W J 5.6KΩ	RRXAJBBZ0562
R 118	CHIP RES. 1/10W J 33Ω	RRXAJBBZ0330
R 119	CHIP RES. 1/10W J 1.5KΩ	RRXAJBBZ0152
R 120	CHIP RES. 1/10W J 68Ω	RRXAJBBZ0680
R 122	CHIP RES. 1/10W J 120KΩ	RRXAJBBZ0124
R 123	CHIP RES. 1/10W J 100KΩ	RRXAJBBZ0104
R 124	CHIP RES. 1/10W J 1.8KΩ	RRXAJBBZ0182
R 126	CHIP RES. 1/10W J 1KΩ	RRXAJBBZ0102
R 128	CHIP RES. 1/10W J 3.3KΩ	RRXAJBBZ0332
R 129	CHIP RES. 1/10W J 120Ω	RRXAJBBZ0121
R 130	CHIP RES. 1/10W J 1.5KΩ	RRXAJBBZ0152
R 131	CHIP RES. 1/10W J 560Ω	RRXAJBBZ0561
R 132	CHIP RES. 1/10W J 100Ω	RRXAJBBZ0101
JW 235	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 236	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 237	CHIP RES. 1/10W J 0Ω	RRXAJBBZ0000
JW 239	CHIP RES. 1/10W J 0Ω RRXAJBBZ00
	VARIABLE RESISTOR
VR 101	POTENTIOMETER 10KQ B V	138J917
	MISCELLANEOUS
CF 101	CERAMIC DISCRE CDA5.5MC26	1812020
CF 102	CERAMIC DISCRE CDA6.5MC26	1813594
CF 103	CERAMIC TRAP TPW02B	1813593
CF 104	CERAMIC FILTER SFE5.5MBF 1812018
CF 105	CARAMIC FILTER SFE6.5MB	1813595
IC 101	IC LA7530N	14LQ162
SAW101	SAW FILTER KAF-38 OMB-MH

CHASSIS ELECTRICAL PARTS

Ref. No.	Description	Part No.
CRT 1 🛧	CRT 370KBR22-TC09 (SPYB) or	1812341
	CRT 37GDA85X-TC01(P) or	1812724
	CRT A34KPU02XX48	TCRT190GS011
L 502 🛧	DEGAUSSING COIL or	LLBH00ZTZ011
	DEGAUSSING COIL	LLBH00ZAB006
LD 1	WIRE ASS'Y	WX1L7500-001
LD 4	WIRE ASS'Y	WX1L7401-001
SP 801	SPEAKER S08J59A or	1520614
	SPEAKER R77A80A32X009 or	DSD0808DJ001
	SPEAKER SG-3B018B	152N589

L7483EL

Page 21

PAL Color Bar Signal (with 1KHz Audio Signal) INPUT : RECEIVING CH. : E2 ch (48.25 MHz) PRESET MODE : Press Picture Select button on the remote control unit, then press the number "1" button.

WF1

WF2

WF3

WF4

1DIV: 1V 10 µ sec

WF8 1DIV: 20V 10 µ sec

(Brightness--- Center Color--- Center Contrast--- Approx 70%)

WF16 1DIV: 1V 10 µ sec

WF12 1DIV: 0.5V 5msec

Page 22

WIRING DIAGRAM

Page 23

BLOCK DIAGRAM

Page 24

15. WHITE BALANCE ADJUSTMENT

Purpose: To mix red, green and blue beams correctly for pure white. Symptom of Misadjustment: White becomes bluish or reddish.

Reference Notes: VR602, VR603 --- CRT PCB

1. Operate the unit more than 20 minutes.
2. Face the unit to east. Degauss the CRT using Degaussing Coil.
3. Input the White Raster (APL 100%).
4. Set the color analyzer to the CHROMA mode and after zero point calibration, bring the optical receptor to the center on the tube surface (CRT).
5. Adjust VR603 (R. DRIVE) and VR602 (B. DRIVE) so that the respective chroma temperatures become 8000K-10MPCD (x : 0.300 / y : 0.290) ±4%.

Note: Confirm that Cut Off Adj. is correct after this adjustment, and attempt Cut Off Adj. if needed.

SCHEMATIC DIAGRAMS / PCB'S AND TEST POINTS

STANDARD NOTES

Warning

Critical components having special safety characteristics are identified with a A by the Ref. No. in the parts list and enclosed within a broken line * (where several critical components are grouped in one area) along with the safety symbol A on the schematics or exploded views.

Use of substitute replacement parts which do not have the same specified safety characreristics may create shock, fire, or other hazards.

Under no circumstances should the original design be modified or altered without written permission from Funai Electric Company. Funai assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability.

Notes:

① Do not use the part number shown on these drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
② All resistance values are indicated in ohms (K=10³, M=10⁶).
③ Resistor wattages are 1/5W or 1/6W unless otherwise specified.
④ All capacitance values are indicated in µF (P=10^-6µF).

Note of Capacitors:

(M) --- Mylar Cap. (SC) --- Semiconductor Cap. (TF) --- Stacked Metallized Film Cap.

Temprature Characteristics of Capacitors are noted with the following:

(YB) --- ±10% (SR) --- ±15% (NP0) --- 0±60ppm/°C (SL) --- +350~-1000ppm/°C

Tolerance of Capacitors are noted with the following:

(K) --- ±10% (Z) --- +80~-20%

Note of Resistor:

F --- Fuse Res.

Page 25

Page 26

Page 27

Page 28

Page 29

VOLTAGE CHART

Pin No.

10 11 12

Pin No.

5 6

9 10

23 24

IC207

16.3

11.8

IC202

2.5

5.0

5.0 5.0

5.0

IC203

6.0

5.9

6.9

7.0

11.7

4.6

5.0

6.0

11.7

IC208

32.0

IC209

2.5 2.5

4.9

2.5

2.6 3.3

2.7

0.2

2.2

3.8

1.7

4.9

2.5

IC204

13.0

0.8

0.7

(Unit: Volt)

IC205

11.0

4.9

*0.7~11.3

7.2

7.5

15.5

IC210

11.8

8.9

Pin No.	IC101	IC201	IC206
1	5.7	4.6	2.8
2	4.7	3.5	4.3
3	5.4	2.6	5.8
4	3.9	2.0	4.6
5	3.9	* 5.0~0.1	5.8
6	4.3	0	5.8
7	4.3	5.0	6.6
8	0	0	4.4
9	1.4	2.4	NC
10	4.8	2.5	4.4
11	6.0	2.5	0
12	3.8	5.0	0
13	8.4	5.0	0
14	8.4	5.0	0
15	3.8	5.0	3.1
16	4.4	5.0	5.0
17	11.7	0	2.9
18	0	NC	0.9
19	3.0	5.0	8.9
20	3.0	3.5	0.2
21		0	4.8
22		NC	0
23		0	0
24		0	2.2
25		0	9.0
26		4.1	3.6
27		5.0	0.5
28		3.0	0
29		3.0	4.2
30		0	5.2
31			3.0
32			0.6
33		4.9	0.4
34		0	6.1
35		5.0	6.1
36		4.5	5.8
37		0	2.5
38		5.0	2.6
39		0	2.5
40		0	3.9
41		0	4.8
42		5.0	6.8
43			2.6
44			3.3
45			3.6
46			6.3
47			8.9

V	oı	. \|	М	IN	~	М	ax

Input: PAL Color Bar Signal (with 1KHz Audio Signal) Receiving Ch.: E2 ch (48.25 MHz) Preset Mode: Press Picture Select button on the remote control unit, then press the number "1" button. Brightness--- Center Color--- Center Contrast--- Approx 70%

L7530V0	C

Page 30

(L7483SC-MA

7-3

FUNAI Service manual / Схема, сервісна інструкція Service manual & schematics

14" COLOR TELEVISION MS-14 MS-14

IMPORTANT SAFETY NOTICE

TABLE OF CONTENTS

GENERAL SPECIFICATIONS *

FEATURE and SPECIFICATIONS

Regulations:

JACKS and TERMINALS

CONTROL and SWITCHES

ACCESSORIES

PERFORMANCE SPECIFICATIONS

< Tuner >

< Video & Chroma>

<Audio>

All items are measured across 16Ω resistor at speaker output terminal.

IMPORTANT SAFETY PRECAUTIONS

Safety Precautions for TV Circuit

5. Hot Chassis Warning -

Precautions during Servicing

Safety Check after Servicing

1. Clearance Distance

Table 1 : Ratings for selected area

2. Leakage Current Test

Measuring Method : (Power ON)

Table 2 : Leakage current ratings for selected areas

DISASSEMBLY INSTRUCTIONS

1. DISASSEMBLY FLOW CHART

CAUTION !: When removing the CRT, make sure to discharge Anode Lead of the CRT. Use the CRT Ground Wire to discharge the CRT before removing the Anode Cap.

2. DISASSEMBLY METHOD

Reference <Notes> in Table

Caution !

ELECTRICAL ADJUSTMENT INSTRUCTIONS

NOTE:

TEST EQUIPMENT REQUIRED:

HOW TO SET UP THE ADJUSTMENT MODE:

1. POWER SUPPLY DC VOLTAGE ADJUSTMENT

Purpose: To get correct voltage.

2. 38.0MHz PEAK ADJUSTMENT (for TUNER)

3. AFT CURVE ADJUSTMENT (for TUNER)

Purpose: To operate AFT correctly.

4. RF AGC ADJUSTMENT (for TUNER)

Reference Notes: TU201 --- MAIN PCB VR101 --- IF PCB

5. 4.43MHz ADJUSTMENT

6. 3.58MHz ADJUSTMENT

Reference Notes: C298 --- MAIN PCB

7. V. SIZE ADJUSTMENT

Purpose: To get correct vertical size of screen image.

8. CUT OFF ADJUSTMENT

Note: Confirm that White Balance Adj. is correct after this adjustment, and attempt White Balance Adj. if needed.

9.1 H DELAY LINE ADJUSTMENT (for PAL)

10. BELL FILTER ADJUSTMENT (for SECAM)

11. R-Y DEMODULATE COIL ADJUSTMENT (for SECAM)

12. B-Y DEMODULATE COIL ADJUSTMENT (for SECAM)

13. SUB BRIGHT ADJUSTMENT

14. FOCUS ADJUSTMENT

MECHANICAL PARTS LIST

ELECTRICAL PARTS LIST

MMA PCB ASSEMBLY

MAIN PCB (MMA-A)

CRT PCB (MMA-B)

CHASSIS ELECTRICAL PARTS

PAL Color Bar Signal (with 1KHz Audio Signal) INPUT : RECEIVING CH. : E2 ch (48.25 MHz) PRESET MODE : Press Picture Select button on the remote control unit, then press the number "1" button.

WIRING DIAGRAM

BLOCK DIAGRAM

15. WHITE BALANCE ADJUSTMENT

Note: Confirm that Cut Off Adj. is correct after this adjustment, and attempt Cut Off Adj. if needed.

SCHEMATIC DIAGRAMS / PCB'S AND TEST POINTS

STANDARD NOTES

Warning

Notes:

Note of Capacitors:

Temprature Characteristics of Capacitors are noted with the following:

Tolerance of Capacitors are noted with the following:

Note of Resistor:

VOLTAGE CHART

(Unit: Volt)