Key Features 1
IMPORTANT SAFEGUARDS 1-2
Before Handling the Product 2
Components 2
Installation 2
Assembly 3
Mounting Antenna on Mast 3
System Connection Diagram 3
Operating Antenna 3
Specifications 4
FUNAI CORPORATION LIMITED WARRANTY 4
Principales detalles 5
SEGURIDAD IMPORTANTE 5-6
Antes de manipular el producto 6
Componentes 6
Instalación 6
Armado 7
Colocación de la antena en el mástil 7
Diagrama de conexión del sistema 7
Operación de la antena 7
Especificaciones 8
GARANTIA LIMITADA DE FUNAI CORPORATION 8
● Experience and knowledge of certain techniques are required for
work relating to antennas and television reception. Contact the
retailer that you purchased the antenna from or a business that
provides this service when required.
● Do not affix any label on, paint, or cover the Smart Antenna Unit
and elements.
● Do not install the antenna in locations such as the following:
• Near power lines, neon signs, overhead wires and telephone
wires
• Where the construction is not solid, the ground is soft, it is rickety,
or it vibrates
• Where the antenna may impede the passage of people or
vehicles
• Near a chimney or where the temperature becomes high
● Do not conduct installation work when the weather is bad due to
strong wind, rain, snow, fog or other conditions. This can cause
injury resulting from the product falling or being toppled.
● Do not conduct installation work when there are poor footholds
including an unstable position. This can cause injury resulting from
falling or slipping.
● As electric currents flow through the coaxial cable that is
connected to the antenna, do not nick, bend forcefully, put
anything heavy on, or heat the coaxial cable. This can cause fire or
an electric shock.
● Do not tamper with the interior of the antenna by opening the case
or disassembling the antenna. This can cause an electric shock or
injury. For inspection, adjustment or repair of the interior, contact a
retailer or a business that provides this service.
● Do not stand on the antenna or installation devices or hang on
them. This can cause damage or injury resulting from the product
falling or being toppled. Caution is especially required in
households with a child.
● Do not touch the antenna or cables when there is lightning. This
can cause an electric shock.
● Do not drop components of the antenna or tools from a high
position. This can cause injury.
● Firmly secure screws and bolts used for assembly or installation by
tightening them with the specified torque if it is provided. Failure to
do so can cause injury resulting from the product falling or being
toppled.
● Do not conduct any maintenance work such as inspection of the
antenna or installation devices when the weather is bad due to
wind, rain, thunder, lightning, snow or other conditions. This is
dangerous and can cause injury resulting from the product falling
or being toppled.
Instruction
Manual
Thank you for purchasing a DX Antenna product.
● Please read this instruction manual carefully prior to using the product to ensure proper understanding and usage.
● Keep this manual in a safe place for future reference.
SMART ANTENNA DTA-5000
CONTENTS
Key Features
INDICE
● The antenna direction can be adjusted for optimal reception according to the received channel and in synchronization with an ATSC
Receiver (Note 1).
● Directivity is 360 degrees, and the direction can be automatically selected from 16 phases in the scale. Airwaves from any direction can be
received.
● You need only this antenna to receive all TV channels on VHF and UHF.
● With the built-in low noise amplifier and automatic gain controller, the antenna can be used in locations where weak airwaves are received
as well as locations where strong airwaves are received.
(Note 1) The ATSC Receiver with EIA/CEA-909 Standard Interface
IMPORTANT SAFEGUARDS
WARNING
The followings indicate a potentially hazardous situation that could result in serious injury or death if the instructions are ignored and the
product is handled incorrectly as a result.
1
CAUTIONS
The followings indicate a potentially hazardous situation that could result in equipment damage or malfunction if the instructions are
ignored and the product is handled incorrectly as a result.
● After a typhoon or snowfall, an anomaly may be found in the
antenna or installation devices or they may have been loosened. If
you leave them in this state, damage may be caused and that may
result in injury or a malfunction. For inspection, contact the retailer
that you purchased the antenna from or a business that provides
this service.
● Do not hang your laundry or other items on the antenna or
installation devices. This can cause damage or injury resulting
from the product being toppled.
● There may be restrictions on installation of an antenna if you live in
a condominium or apartment building. Make sure you ask your
management committee, management office, residents'
association or others about such restrictions before installing the
antenna.
● Install the antenna in a location where no one can touch the
antenna elements. Failure to do so may cause injury such as an
injured eye resulting from being struck by an element tip.
Before Handling the Product
● This product is intended for home use.
● This antenna can only be used with an ATSC Receiver that has a smart antenna feature (that conforms to the EIA/CEA-909
standard) or a television with a built-in ATSC Receiver.
● Read this instruction manual thoroughly before starting assembly or installation work.
● Do not conduct installation work when the weather is bad due to strong wind, rain, snow or other conditions as it is dangerous.
● Be sure not to drop, bump or apply unnecessary pressure on the antenna.
● When installing the product in locations including a roof, wall or handrail of a balcony, make sure they are strong enough. Secure
the product firmly so that it can hold for a prolonged period even if there are strong winds due to a typhoon or other conditions.
Consider the safety and reliability of installation sufficiently to prevent the product from falling or being toppled.
● Supply power after making sure all cables are completely connected.
Components
Installation
1 Smart Antenna Unit 1
2 Elements 4
3 Antenna Control Box
(DPI-10) 1
4 Bracket A 1
5 Bracket B 1
6 Bracket Cover 1
7 Screws
(Small: No.10-32✕7/16) 4
8 Screws
(Large: No.10-32✕1•1/4) 2
9 Weather Boot 1
10
Screws to secure elements
(small: No.8-32✕7/16) 4
11
Antenna Control Cable
(1.64 ft) 1
12
Coaxial Cable (1.64 ft) 1
Note:This antenna system does not include a DIGITAL
(ATSC) Receiver.
2
Caution:
(NOT INCLUDED)
Items required for
installation
1 Mast (ø1.26"-ø1.69")
2 Screwdriver (Phillips
)
3 Coaxial Cable
(RG6 or RG59)
● To receive terrestrial digital broadcasts, airwaves must be over a certain level of strength. If the antenna is installed in locations where
airwaves are weak or the strength level of airwaves is lowered by obstacles in the surroundings that block airwaves or reflect them,
terrestrial digital broadcasts may not be received at all.
● Install the antenna horizontally by using a strong mast (ø1.26" - ø1.69") in a location where the antenna does not impede people's daily
activities.
● When the antenna is installed in a balcony, use mounting hardware (not included) compatible with a mast that has a 1.26" to 1.69" diameter.
● Fasten the antenna firmly to a mast.
● The reception direction of the antenna can be automatically selected from a scale of
360 degrees (in 16 phases) with the secured antenna controlled by signals from an
indoor Receiver. However, if the antenna is installed in a location where there is a
metal obstacle in the surroundings or where signals are blocked by obstacles such
as a building, a wall or a tree beside the antenna, selecting the reception direction
may have no effect and pictures may be distorted.
● Install the antenna as high as possible so that obstacles will not hamper reception in
the direction that signals or airwaves are coming from.
● When the antenna is installed on a roof or the ground, secure the mast firmly by
using a stay wire in three to four different directions.
● Do not install the antenna by hanging it upside down from a ceiling, etc.
Assembly
1. Insert the element into the opening for attaching that element in
the Smart Antenna Unit.
2. Secure the element by tightening the screw included for
attaching the element.
Smart Antenna Unit
Mounting Slot for Element
Element
Element
Smart Antenna Unit
Mounting Screw for Element
System Connection Diagram Operating Antenna
1. Confirm that the cables are connected
according to the System Connection
Diagram, and then turn on the power
switch of ATSC Receiver.
2. Make adjustments by using the
“Antenna Setting” for the ATSC
Receiver. (See the instruction manual
included with the ATSC Receiver for
details.)
3. Reception of the antenna is
automatically adjusted to the best
setting by control signals from the
ATSC Receiver.
<NOTE>
Do not reverse connect the antenna
terminal and the TV (STB) terminal on the
Antenna Control Box. This can cause the
receiver to fail.
Caution:
• The antenna can normally be pointed in any direction during installation.
If fine-tuning is necessary, the antenna can be turned slightly until the best picture is received.
• Install the antenna using a strong mast in a location where people are not likely to come in contact with the antenna.
• Do not disassemble the product or modify it.
• When the antenna is connected with the Antenna Control Box, make sure that an RG-59 coaxial cable or greater (not included) is used.
Also make sure the coaxial cable between the Smart Antenna Unit and the Antenna Control Box is 150 ft long or less when wiring is carried
out.
<Note> No direction adjustment is required when this antenna is installed.
Smart Antenna Unit
Coaxial Cable
(not included)
TV Signal
TO TV (STB)
ANTENNA CONTROL
TO
ANTENNA
Antenna Control Cable
Antenna Control Signal
TV Signal
Coaxial Cable
Control
Signal
Power
Antenna
Control Box
ATSC Receiver or TV (built-in ATSC Receiver)
* Conforms to the EIA/CEA-909 standard
3
1. Attach bracket A to the Smart Antenna Unit using the
4 screws. (Fig.
●●
1 ) (screw torque:approximately 3N·m)
2. Place mast through the mounting bracket cover.
(Fig.
●●
2 )
3. Insert mast between bracket A and bracket B, then
tighten firmly using 2 screws. (Fig.
●●
3 )
(screw torque:approximately 3N·m)
4. Attach the mounting bracket cover to the Smart
Antenna Unit by turning cover clockwise until you hear
a click. (Fig.
●●
4 )
5. Cut the end of the Weather Boot to match the thickness
of the coaxial cable, then insert the cable.
(Fig.
●●
5 )
6. Connect the coaxial cable to the body and cover the
connector plug with the Weather Boot. (Fig.
●●
6 )
● For connection details, please refer to
the instruction manual of the ATSC
Receiver.
● Do not connect any other device to the
coaxial cable between the Smart
Antenna Unit and the Antenna Control
Box as electric currents and control
signals are piggybacked on the coaxial
cable. Never short out the conductor
and the braided wire in the coaxial
cable. This can cause damage.
● Turn on the power for the ATSC
Receiver after all devices are
connected.
● This antenna is intended for use with
one ATSC Receiver or one TV (built-in
ATSC Receiver) only.
Do not connect the antenna to two or
more of these devices using a splitter,
etc.
● Do not connect any antenna (such as a
Yagi-Type antenna) other than a Smart
Antenna to the antenna terminal on the
Antenna Control Box.
Mounting Antenna on Mast
Screws
(small)
Bracket A
Smart Antenna Unit
Screws
(
large
)
Mast
Bracket A
Bracket B
Connector
Coaxial Cable
Waterproof Cap
Cut
Frequency 54 to 806 MHz
Impedance 75 Ω (F-type)
Antenna Control Jack Modular Antenna Control Connector
Dimensions 1·
15
/16(H) x 3·7/32(W) x 2·13/32(D) [inch]
33.4 (H) x 82 (W) x 61 (D) [mm]
Weight 0.15 kg
0.33 lb
Band Zone VHF (Low) VHF (High) UHF
Frequency 54 to 88 MHz 174 to 216 MHz 470 to 806 MHz
Gain 5 to 20 dB 10 to 20 dB 15 to 25 dB
Directivity 360 degrees, 16 directions (automatic)
Impedance 75 Ω (F-type)
Polarization Horizontal
Power Consumption 12 VDC, 150 mA (max.)
Compatible Mast
ø1.26 to 1.69 [inch]
Diameter ø32 to 43 [mm]
Dimensions 4·
17
/32(H) x 28·15/16(W) x 28·15/16(D) [inch]
∗1 115 (H) x 735 (W) x 735 (D) [mm]
Weight 1.5 kg
3.31 lb
Funai Corporation will exchange or repair this product, at its option, in the
event of defect in materials or workmanship as follows:
REPAIR DURATION:
LABOR: FUNAI CORPORATION will provide the labor without
charge for a period of ninety (90) days from the date of
original retail purchase.
PA RT S: FUNAI CORPORATION will provide parts to replace
defective parts without charge for a period of one (1) year
from the date of original retail purchase.
Certain parts
are excluded from this warranty.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE RECEIPT OR OTHER PROOF OF ORIGINAL
RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH THE PRODUCT TO OBTAIN EXCHANGE OR SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product
are altered, replaced, defaced or missing. This FUNAI CORPORATION
Limited warranty applies only to product purchased and used in the United
States.
This warranty only covers failures due to defects in material or workmanship,
which occur during normal use. It does not cover damage which occurs in
shipment, or failures which are caused by repairs, alterations, or parts not
supplied by FUNAI CORPORATION, or damage which results from accident,
misuse, abuse, mishandling, misapplication, alteration, faulty installation,
improper maintenance, commercial use such as hotel, rental or office use of
this product, or damage which results from fire, flood, lightning or other acts
of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY
ACCESSORIES (EXCEPT REMOTE CONTROL UNITS), ANY COSMETIC
PA RTS, COMPLETE ASSEMBLY PARTS, DEMONSTRATION OR FLOOR
MODELS.
FUNAI CORPORATION AND ITS REPRESENTATIVES OR AGENTS SHALL
IN NO EVENT BE LIABLE FOR ANY GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE USE
OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS
MADE IN LIEU OF ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANT ABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, THAT ARE HEREBY DISCLAIMED BY FUNAI CORPORATION AND
ITS REPRESENTATIVES OR AGENTS IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED
BY A FUNAI AUTHORIZED CENTER. THIS WARRANTY IS VALID WHEN
THE PRODUCT IS DELIVERED PREPAID TO A FUNAI AUTHORIZED
SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU
MAY HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE, IF AT
ANY TIME DURING THE WARRANTY PERIOD YOU ARE UNABLE TO
OBTAIN SATISFACTION WITH THE EXCHANGE OR REPAIR OF THIS
PRODUCT, PLEASE CONTACT FUNAI CORPORATION.
ATTENTION:
FUNAI CORPORATION RESERVES THE RIGHT TO MODIFY
ANY DESIGN OF THIS PRODUCT WITHOUT PRIOR
NOTICE.
For information about your product, or for information on how
to exchange or repair your product, telephone or write to the
following:
FUNAI CORPORATION
Customer Service
Head Office: 100 North Street, Teterboro, NJ 07608
19900 Van Ness Avenue, Torrance, CA 90501
CALL 1-800-481-1652
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
FUNAI CORPORATION LIMITED WARRANTY
EXCHANGE DURATION:
FUNAI CORPORATION will exchange for a new unit without charge for a
period of ninety (90) days from the date of original retail purchase.
FUNAI CORPORATION will exchange for a factory-service-to-new-condition
unit for a charge of a retailed price unit for the period of ninety one (91) days
to three hundred sixty five (365) days from the date of original retail
purchase.
All rights reserved.
E-4020
Manufactured by: Kobe, Japan
Smart Antenna Unit Antenna Control Box (with EIA/CEA-909 Standard Interface)
Specifications
4
Specifications are subject to change without notice due to product improvements.
∗1 Including VHF Element