Fujitsu PA03338-B005 - FI-5750C Image Scanner, fi-5750C Getting Started Manual

Page 1
Getting Started
P3PC-E737-01-EN
fi-5750C Image Scanner
Page 2
Page 3

Introduction

Thank you for purchasing the fi-5750C Duplex Color Scanner product.
Connect the equipment into an outlet on
a circuit different from that to which the receiver is located.
Consult your dealer or an experienced
radio/TV technician.
The “Operator’s Guide” is guide is stored on the User Manual CD-ROM. The guide pro­vides useful and detailed information on opera­tion, daily care, replacement of consumables and trouble shooting, etc. Please also read the Operator’s Guide for your reference.

Regulatory Information

FCC declaration
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res­idential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harm­ful interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful interfer­ence to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the follow­ing measures:
FCC warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
ATTENTION
• The use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.
• The length of the AC cable must be 3 meters (10 feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital apparatus set out in the Radio interfer­ence Regulations of the Canadian Department of Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescridtes dans le Réglesment sur le brouillage radioélectrique dicté par le ministere des Communications du Canada.
Cet appareil numérique de la classe B est con­formme à la norme NMB-003 du Canada.
Bescheinigung des Herstellers / Importeurs
Reorient or relocate the receiving
antenna.
Increase the separation between the
equipment and receiver.
H i e r m i t w i r d b e s c h e i n i g t , d a ß d e r / d i e / d a s fi-5750C
i
Page 4
In Übereinsstimmung mit den Bestimmungen der EN45014(CE) funkentstört ist.
Laut Maschinenlärminformationsverordnung
3. GS GV, 18.01.1991:Der höchste Schalldruckpegel beträgt 70 dB (A) oder weni­ger gemäß ISO/7779.
International ENERGY STAR® Program
As an ENERGY STAR® Partner,
PFU LIMITED has determined that this product meets the
degree of safety is required, for example, in the control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic control, operation control in mass­transport systems, medical equipment for sustaining life, and missile firing control in weapons systems, and when provisionally the safety in question is not ensured. The user should use this product with adopting measures for ensuring safety in such high-safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of this product by the user in high-safety applications, and for any claims or compensation for damages by the user or a third party.
ENERGY STAR® guidelines for energy efficiency.
The International ENERGY STAR® Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment. The program backs the development and dissemination of products with functions that effectively reduce energy consumption. It is an open system in which business proprietors can participate voluntarily. The targeted products are office equipment such as computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and
logos ( ) are uniform among participating nations.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be used in office, personal, domestic, regular industrial, and general-purpose applications. It has not been designed and manufactured for use in applications (simply called "high-safety applications" from here on) that directly involve danger to life and health when a high
About the use of mercury
The scanner lamp contains mercury.
To avoid unexpected injury, read the following carefully.
Doing the following actions may result in seri­ous personal injuries:
Do not put the substance in the lamp in
your mouth as it contains mercury.
Do not incinerate, crush, or shred the
scanner.
Do not breathe the chemical liquid
contained in the scanner parts.
Disposing of the scanner should be conducted as required by local ordinances or regulations.
Trademarks
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the United States and/or other countries. Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incor­porated in the United States and/or other coun­tries. ISIS, QuickScan and their respective logos are trademarks or registered trade marks of Pixel
ii
Page 5
Translations, a division of Captiva Software Corporations in the United States. Other product names are the trademarks or reg­istered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as follows:
Manufacturer
PFU LIMITED
International Sales Dept., Imaging Business Division, Products Group
Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan
Windows 95: Microsoft® Windows® 95
operating system.
®
Windows 98: Microsoft
operating system.
Windows Me: Microsoft
lennium Edition operating system.
Windows 2000: Microsoft® Windows® 2000
Professional operating system.
Windows XP: Microsoft® Windows® XP
Professional operating system,
Microsoft® Windows® XP Home Edition operating system.
Windows NT: Microsoft® Windows NT®
Server operating system Version 4.0,
Microsoft Workstation operating system Version 4.0.
Where there is no distinction between the dif­ferent versions of the above operating system, the general term "Windows " is used.
Windows® 98
®
Windows® Mil-
®
Windows NT®
Phone : (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2003.

Note, Liability

READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU assumes no liability to any party for any damage caused by errors or omissions or by statements of any kind in this manual, its updates or supplements, whether such errors are omissions or statements resulting from negligence, accidents, or any other cause. PFU further assumes no liability arising from the application or use of any product or system described herein; nor any liability for incidental or consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the information contained herein, whether expressed, implied, or statutory.
iii
Page 6

Preface

Symbols Used In This Manual
Safety Precautions
This manual describes important details for ensuring the safe and correct use of this product. Thoroughly read this manual before you start to use this product. In particular, be sure to read and fully understand the Safety Precautions described in this manual before you use this product. Also, store this manual in a safe place so that it can be easily referred to during use of this product.
Warning Indications Used In This Manual
This manual uses the following indications to ensure safe and correct use of this product, and to prevent possible danger and injury to the operator and other persons.
WARNING
This indication alerts operators to an operation that, if not strictly observed, may result in severe injury or death.
CAUTION
This manual uses the following symbols in explanations in addition to warning indications.
ATTENTION
HINT
R
This symbol alerts operators to particularly important information. Be sure to read this information.
This symbol alerts operators to helpful advice regarding operation.
A TRIANGLE symbol indicates that special care and attention is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not perform.
The drawing inside or under the circle shows the specific action that is not allowed.
Outline characters on a colored background show instructions users should follow.
It may also include the drawing that shows the specific instruc­tion.
This indication alerts operators to an operation that, if not strictly observed, may result in safety hazards to personnel or damage to equipment.
iv
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the interest of product improvement. If the actual displayed screen differs from the screen examples in this manual, operate by following the actual displayed screen while referring to the User's Manual of the scanner application you are using. Furthermore, the screenshots in this manual are for FUJITSU TWAIN 32 scanner driver,
Page 7
ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner driver, QuickScan™
image capturing software and Adobe Acrobat.
About Maintenance
The user must not perform repairs on this scanner. Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service provider to make repairs to this product.

Safety Precautions

Use this scanner only at the indicated power voltage. Do not connect to multiple-power strips.
Use this scanner only at the indi­cated power voltage and cur­rent. Improper power voltage and current might cause fire or electric shock.
Also, do not connect to multiple­power strips.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry cloth. Accumulated dust might cause fire or electric shock.
WARNING
The following describes important warnings described in this manual.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so might cause electric shock.
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock.
Do not place heavy objects on AC cables, or pull, bend, twist, heat, damage or modify AC cables.
Also, do not use damaged AC cables or power plugs, and AC cables or power plugs when the wall socket is loose.
Use only specified AC cables and connector cables
Use only specified AC cables and connector cables. Failure to use the correct cables might cause electric shock and equipment failure.
Do not install in locations subject to oil smoke, steam, humidity, and dust.
Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust. Doing so might cause a fire or electric shock.
Do not use the scanner if you smell strange odor.
If you detect heat coming from the device or detect other prob­lems such as smoke, strange smells or noises, immediately turn off the scanner and then dis­connect its power plug.
Make sure that the smoking has stopped, and then contact the store where you bought the scanner or an authorized FUJITSU scanner service provider.
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn off the scanner and unplug the power cable before contacting the store where you purchased the scanner.
v
Page 8
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner.
Do not scan wet documents or documents with paper clips or staples.
Do not splash or allow the scan­ner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner, immediately turn off the scanner and disconnect the power plug from the power outlet, then contact the store where you bought the scanner or the Maintenance Service Center.
Pay particular attention to this warning in households where there are small children.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner contains high-voltage components. Touching these components might cause fire or electric shock.
CAUTION
The following describes important cautions described in this manual.
Do not install the scanner on unsta­ble surfaces.
Install the scanner on a desk so that none of its parts protrude outside of the desktop. Also, make sure that the scanner is installed on a flat, level surface.
Do not install the scanner on unstable surfaces. Install the scanner on a level surface that is free of vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the scanner and other devices.
Firmly insert the power plug.
Firmly insert the power plug into the power outlet as far it can go.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside of scanner, which may results in fire or scanner failure.
Do not place heavy objects or climb on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's top surface for performing other work. Improper installation might cause injuries.
Before moving the scanner, disconnect the power plug from the power outlet.
Do not move the scanner with the power and interface cables connected as this might damage the cables, causing fire, electric shock or injuries.
Before moving the scanner, be sure to disconnect the power plug from the power outlet, and disconnect data cables. Also, make sure that the floor is free of obstructions.
Do not use the scanner immediately after moving it from a cold place into a warm room.
Do not use the device immedi­ately after moving it from a cold place into a warm room. This may cause condensation, which might lead to scanning errors. Let the device dry about one or two hours before you use it.
vi
Page 9
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of electronic noise. Also, protect the scanner from static electricity as this might cause the scanner to malfunction.
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt and dust to enter the scanner, resulting scanner failure and malfunction.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism when scanning as this may cause injuries.
Before moving the scanner, make sure the shipping lock and the ADF lock screws are locked.
When moving the scanner, be sure to lock the shipping lock and the ADF lock screws in order to prevent damages to the scanner.
Disconnect the power plug from the power outlet when the scanner is not used for a long period of time.
When the scanner is not used for a long period of time, be sure to disconnect the power plug from the power outlet for safety.
Do not install the scanner in the direct sunlight.
Do not install the scanner in the direct sunlight or near heating apparatus. Doing so might cause excessive heat to build up inside the scanner, causing fire or scan­ner trouble. Install the scanner in a well-ventilated location.
Do not try to move or lift the scanner alone.
This scanner is heavy (77.2lbs/ 35kg). When you carry the scan­ner, ensure that additional per­sonnel are used.
vii
Page 10
viii
Page 11

Contents

Introduction................................................................. i
Regulatory Information ............................................... i
Note, Liability............................................................ iii
Preface ..................................................................... iv
Safety Precautions .................................................... v
Chapter1 PREPARING THE SCANNER..... 1-1
1.1 Checking the contents of scanner package.............1-2
1.2 Names and function of parts....................................1-2
1.3 Functions of the operator panel...............................1-3
Chapter 2
INSTALLATION OF THE SCANNER
2.1 Installing the scanner...............................................2-2
2.2 Connecting the scanner to your PC.........................2-2
2.3 Installing the Scanner Application ...........................2-4
... 2-1
Appendix ....................................................AP-1
Appendix 1Troubleshooting ............................................... AP-2
Appendix 2Daily Care ................................................... AP-6
Appendix 3Replacing Consumables .................................. AP-8
Appendix 4Setting the position of the ADF ........................ AP-9
ix
Page 12
x
Page 13

Chapter1 PREPARING THE SCANNER

1.1 Checking the contents of scanner package 1-2
1.2 Names and function of parts ...................... 1-2
1.3 Functions of the operator panel .................. 1-3
1-1
Page 14

1.1 Checking the contents of scanner package

When you unpack the scanner package, make sure that the package contains all the parts on the list included in the package. If any parts are missing or defective, contact your sales representative. Handle the scanner and accessories with care.

1.2 Names and function of parts

This section describes the names of parts and their functions.
Front (Flat Bed unit opened view)
TABL E 1.
No. Name Function
5 Screw Storage
Holes
6 Handle Used to open/close the
Holes in where the ADF Lock Screws are placed after unlocking the ADF.
Document Cover.
Front
TABL E 1.
No. Name Function
1Document
Cover
2 Document Bed For scanning documents
3Document
Holding Pad
4 ADF Lock
Screws
When closed, this cover fixes the document set on the reading position.
with the Flat bed, place the document here.
It fixes the document by pressing it onto the document bed.
Used to fix the ADF. They are securing the ADF during transportation.
TAB L E 2.
No. Name Function
7 Operator Panel This panel consists of a
8ADF Paper
Chute
9 Shipping Lock Used to fix the Flatbed’s
10 ADF Button Press this button to open
11 ADF
(Automatic Document Feeder)
12 Stacker Scanned documents are
Function No. display, four buttons and a LED.
For scanning documents with the ADF scanning, place the document here adjusting the side guides to the document width.
carrier unit in order to prevent damages during transportation.
the ADF. It transports a document
to the reading position automatically. According to need, this unit can be set in three directions by turning and sliding it.
ejected from the ADF onto this tray. It is possible to change the height.
1-2
Page 15
Rear ADF
TABLE 3.
No. Name Function
13 EXT connector Connector port for
14 USB Interface
Connector
15 SCSI Interface
Connector
16 SCSI ID
Switch
17 Third Party
Slot (Optional Slot)
18 Side Guide
Button
19 Power Inlet Used for connecting a
20 Power Switch Used for turning ON/
optional units. Used for connecting a
USB interface cable from a PC.
Used for connecting a SCSI interface cable from a PC.
Used for setting SCSI ID (The setting at the factory shipment is ID=5).
The slot for an option board.
Used for adjusting the side guides.
power cable from the power outlet.
OFF the scanner.
No. Name
21 Chute Roller 22 Pick Arm 23 Pick Roller Set 24 Brake Roller 25 Feed Roller 26 Plastic Roller 27 Sheet Guide 28 Ultra Sonic Sensor (Multi feed detection) 29 Glass
TABLE 4.

1.3 Functions of the operator panel

The Operator Panel is located at the right side of the scanner. This panel consists of a function number display, buttons and a LED.
1-3
Page 16
You can change the overlay on the opeartor panel according to your language.
TABLE 5.
Name Function
Function No. display Indicates the function No.
Buttons Function Changes the Function
Send to Launches the linked Scan
LED Power Lights when the scanner
and error status.
activated by the Send to button .
application software
is turned ON.
For details, refer to the "FUJITSU TWAIN32 Scanner Driver User’s Guide", provided in the User Manual CD-ROM, and the "fi-5750C Operator's guide", provided in the Setup CD­ROM.
Indications on the Function No. display
The following shows the indications on the Function No. display.
8
Blinks only one time upon turning on the scanner.
P
Indicates that the scanner has been turned ON and is being initialized.
0
Indicates that initialization will soon be completed.
1
Indicates that initialization has been completed successfully. This status is called "Ready Status".
U
Indicates that a temporary error (that users can solve) has occurred during the initialization or scanning of documents. "U" and an error number (0, 1, 2, 4) are displayed alternately. To return the scanner to the ready status ("1"), press the "Scan" or "Send to" button while the error is indicated.
E
Indicates that a device alarm (that users cannot solve) has occurred during the initialization or scanning of documents. "E" and an "alarm code" (a number or letter) are indicated alternately. To return the scanner to the ready status ("1"), press "Scan" or "Send to" button while the alarm is indicated. If this alarm occurs, turn the power off and then on again. If the alarm is indicated after turning on the power again, contact an authorized FUJITSU scanner service provider.
1-4
Page 17
Chapter 2 INSTALLATION OF THE
SCANNER
2.1 Installing the scanner............................................. 2-2
2.2 Connecting the scanner to your PC....................... 2-2
2.3 Installing the Scanner Application .........................2-4
2-1
Page 18

2.1 Installing the scanner

Place the scanner at its installation site.
1.
For details on the scanner’s dimensions and required installation space, refer to "10 SCANNER SPECIFICATION" in the "fi­5750C Operator's guide".
Unlock the Shipping Lock.
2.
After placing the scanner to the installation site, switch the Shipping Lock into the opened (unlocked) position.
Horizontal position: Lock Vertical position: Unlock
Setting the Stacker
5.
Mount the Stacker onto the scanner aligning the protrusions to the holes on the scanner. You can fix the stacker at two positions: the upper position or the lower position.
Connecting the Power cable.
6.
Remove the ADF Lock Screws.
3.
After placing the scanner to the installation site, remove the ADF Lock Screws and place them into the Storage Holes. For more details about positioning of the ADF refer to "Appendix 4 Setting the position of the ADF" on page 9.
Setting the ADF Paper Chute.
4.
Hold the ADF paper chute and insert its tabs into the holes on the rear side of the ADF as shown in the figure below so that the side guides facing upwards.
Use only the AC cable included the
ATTENTION
Connect the Power cable to a power
7.
outlet.
scanner package.

2.2 Connecting the scanner to your PC

2-2
When running Windows 95 and/or Windows NT 4.0, connect the scanner to your PC with the SCSI interface cable. When running Win­dows 98, Windows Me, Windows 2000 and/or
Page 19
Windows XP, connect the scanner to your PC with either the USB or the SCSI interface cable.
Connecting the SCSI interface cable
Do not connect both the USB interface
ATTENTION
cable and the SCSI cable at the same time. It is not possible to use the USB interface with Windows 95 and/or WindowsNT 4.0.
Connecting the USB Cable
Please connect a USB cable to the
1.
Scanner.
Connect the USB interface cable to the USB interface connector of the scanner.
When using the scanner with the SCSI inter­face, you need to purchase a commercially available SCSI cable and a SCSI card.
SCSI cable
The SCSI has to fit to a 50 Pin half pitch connector and the SCSI card connector of your PC.
SCSI card
Use the recommended SCSI card noted on the fol­lowing website:
http://imagescanner.fujitsu.com/
When connecting the SCSI interface
ATTENTION
Connect the SCSI cable to the scanner.
1.
Connect the SCSI cable to the SCSI interface connector and make sure it is firmly connected.
cable, be sure to first connect the SCSI interface cable then turn on the scanner and your PC. Connect the scanner so that it is the terminated device on the SCSI daisy chain.
Please connect the other end of the
2.
cable to your PC.
Turn ON the scanner.
3.
Turn ON your PC.
4.
Use the USB interface cable provided as
ATTENTION
an accessory for the scanner. Operation with a commercially available USB cable is not guaranteed. When connecting to a USB hub, be sure to connect to the hub nearest your computer (first stage). If you connect it to a USB hub from the second stage onwards the scanner may not operate correctly.
Connect the other end of the cable to
2.
your PC.
For setting the SCSI ID of the scanner,
HINT
please refer to the following section.
Setting the SCSI ID
The factory default setting for SCSI ID is "ID 5". If the SCSI ID of another device has already been set to the same ID, change either the scanner's SCSI ID or that of
2-3
Page 20
the other device. To change the SCSI ID see the following procedure.
Turn the scanner OFF.
1.
Set the SCSI ID.
2.
Set the device address by using the SCSI ID switch on the rear of the scanner.
No. Description:
0 - 7 Can be set as the ID. 8, 9 Used for the factory default value
Turn ON the Scanner.
3.
When the scanner is turned ON, the SCSI ID set at step 2 is enabled.
Turn ON your PC.
4.
TABLE 1.
(SCSI ID=5).
2.3.1 For Fujitsu Twain 32
Scanner Driver
Preparation
Before installing the application, please confirm the following items:
Keep the Setup CD-ROM at hand.
Confirm if the scanner is connected to
your PC correctly.
If an older version of the FUJITSU
TWAIN 32 Driver has already been installed, please uninstall it before installing the new one.
There are two types of FUJITSU TWAIN
32 Drivers. Depending on the operating system (OS) of the computer, the most appropriate driver will be installed automatically.
For Windows 98, Windows Me,
Windows 2000, Windows XP: FUJITSU TWAIN32 V9
For Windows 95 and Windows
NT 4.0: FUJITSU TWAIN32 V8
When using Windows 95 or Windows
NT 4.0: ASPI Manager 4.01 or later is required (generally comes with SCSI board products).
For details on connecting the scanner,
HINT
refer to "2.1 Installing the scanner" on page 2 in this manual.

2.3 Installing the Scanner Application

For scanning documents with this scanner, the scanner driver as well as an image capturing application software (called "application" here­after) must be installed on your PC.
Scanner driver: FUJITSU TWAIN 32 Scanner Driver FUJITSU ISIS Scanner Driver
Application: ScandAll 21 (for TWAIN) QuickScan Pro (for ISIS)
2-4
ATTENTION
Uninstall [Scanner Utility for Microsoft Windows] in [Add/Remove Programs] of the control panel.
Page 21
Installing the FUJITSU TWAIN32 Scanner Driver
Windows XP screenshots are used in this
HINT
Turn the scanner ON.
1.
Turn on your PC and log on to
2.
Windows.
ATTENTION
HINT
section. The windows and operations may slightly vary depending on your OS.
When using Windows NT 4.0, Windows 2000 or Windows XP, log on as a user with "Administrator" privileges (privileges of the administrator of your PC)
The scanner may be detected automatically. If so, [Found New Hardware Wizard] (or [Add/Remove Hardware Wizard]) dialog box will appear. Click [Cancel] to close the Wizard window.
Click [Install Products].
4.
Click [TWAIN Driver] on the window
5.
below.
Insert the Setup CD-ROM into the CD
3.
drive.
The <SETUP DISK START UP SCREEN> will be displayed.
This screen may not appear when the
ATTENTION
"Autoplay" setting of your PC is OFF. In this case, run "Install.exe" in this CD­ROM directly by the "Explorer" or "My Computer".
Error Recovery Guide Installation win-
6.
dow appears.
Error Recovery Guide is a software that displays troubleshooting information on screen if any scanner error occurred. Although you do not install this software, the performance of the scanner would not be affected. However it is recommendable to install this software.
When you select [Yes] for installing Error
ATTENTION
Recovery Guide, [Choose Setup Language] window appears. Select a language and follow the instructions on the window. Error Recovery Guide will automatically start on finishing its installation. Please wait until the installation of TWAIN driver automatically starts.
2-5
Page 22
Select a language used for installa-
7.
tion on [Choose Setup Language] window and click [OK].
Install the application following the
8.
instructions on the window.
2. When any alarm is displayed on [Hard-
ware Installation] window, click the [Continue Anyway] button.
3. Click the [Finish] button.
Now the installation of the scanner driver is completed.
For confirming if the installation was
ATTENTION
successful, perform a scanning operation by using an application that complies with the TWAIN standard such as ScandAll
21.
When the [InstallShield Wizard Com-
9.
plete] window appears, click [Finish].
10.
ATTENTION
Your computer is restarted and the scanner will be detected.
Do not remove the Setup CD-ROM from the CD drive until your PC will be completely restarted.
Depending on the OS, the following operations may be necessary.
Installing ScandAll 21
ScandAll 21 is an imaging software, conform­ing with the TWAIN standards. With the FUJITSU TWAIN 32 scanner driver you can capture scanned image data from the s c a n n e r .
When using Windows NT 4.0, Windows
ATTENTION
Insert the Setup CD-ROM in your CD-
1.
drive
The, <SETUP DISK STARTUP SCREEN> will be displayed.
Click [Install Products].
2.
2000 and/or Windows XP, please login as a user with "Administrator" privileges (privileges of the administrator of your PC).
2-6
For Windows 98: When a request for inserting the CD­ROM of Windows 98 appears, insert it into the CD drive and click the [OK] button.
For Windows 2000: When [Digital Signature not Found] appears, click [Yes].
For Windows XP
1. When [Found New Hardware Wizard]
appears, confirm that the Setup CD-ROM is set in the CD drive, then click the [Next] button.
Page 23
Click [ScandAll 21].
3.
Select an appropriate language from
4.
the <Choose Setup Language> menu and click [OK].
Confirming the installation
Set your documents into the ADF Paper
1.
Chute.
For the loading of documents, please refer to 2.4 "Scanning documents" of the "fi­5750C Operator's Guide".
Start ScandAll 21
2.
From the [Start] Menu, select [Program]­[Scanner Utility for Microsoft Windows]­[ScandAll 21].
Specify the scanner to be used
3.
Select [Select Source] from the [Scan] menu.
Install the application following the
5.
instructions on the screen.
When [InstallShield Wizard Complete]
6.
screen is displayed, click [Finish].
For finishing the installation, it may be
ATTENTION
necessary to restart your computer. Follow the instructions on the window.
In the displayed dialog box, please
4.
select [FUJITSU fi-5750Cdj] or [FUJITSU TWAIN32], then click the [Select] button.
For Windows 98, Windows Me,
HINT
Windows 2000, Windows XP select:
[FUJITSU fi-5750Cdj]
For Windows 95, Windows NT 4.0:
[FUJITSU TWAIN32]
Select [To View] from the [scan] menu.
5.
2-7
Page 24
Set the scanning resolution, document
6.
size etc. on the [TWAIN driver] window (for setting details of the scanning) and click the [Scan] button.
For details about [TWAIN driver],
HINT
The document is scanned and it’s
7.
image will be displayed on the ScandAll 21 screen.
If the scanning is performed successfully, the installation has been finished.
refer to the "FUJITSU TWAIN32 Scanner Driver User Guide" provided on the Setup CD-ROM
Setup CD-ROM
Confirm if the scanner is connected correctly to your
PC.
About connecting your scanner to the
HINT
PC, please refer to "2.1 Installing the scanner" on page 2" of this manual.
Installing FUJITSU ISIS scanner driver
Turn on the scanner.
1.
Turn your PC on an log on to
2.
Windows.
When using Windows NT 4.0, Windows
ATTENTION
HINT
2000 and/or Windows XP, please login as a user with "Administrator" privileges (privileges of the administrator of your PC).
In this manual, Windows XP screens are used. The screens and operations might differ slightly depending on your OS. The scanner is automatically detected and "A detection wizard of the new hardware " or "An addition wizard of new hardware" may be displayed. Please click the [cancel] button and close the wizard screen. (* The screen might differ
slightly depending on your OS)
For details about various types of scanning, refer to the "fi-5750C Operator's Guide", pro­vided on the User Manual CD-ROM.
2.3.2 For Fujitsu ISIS Scanner
Driver
Preparation
Please confirm the following items before installing the ISIS driver:
2-8
Insert the Setup CD-ROM into the CD
3.
Drive.
The <SETUP DISK STARTUP SCREEN> will be displayed.
Page 25
This screen may not be displayed when
ATTENTION
Click [Install Products].
4.
the, “Autoplay” setting of your PC is turned off. In this case, please run "Install.exe" on the CD-ROM directly from explorer or "My Computer".
Select an appropriate language used for
7.
the installation from the <Choose Setup Language> window and click [OK].
Install the application following the
8.
instructions on the window.
When the [InstallShield Wizard Com-
9.
pleted] appears, click on [Finish].
Click [ISIS Driver].
5.
The Error Recovery Guide Installation
6.
window appears.
Error Recovery Guide is a software providing you with troubleshooting information displayed on the screen when a scanner error occurs. Not installing this software will not have an effect on the performance of the scanner. However it is recommended to install this software.
When you select [Yes] for installing Error
ATTENTION
Recovery Guide, [Choose Setup Language] window appears. Select a language and follow the instructions on the window. Error Recovery Guide will automatically start on finishing its installation. Please wait until the installation of ISIS driver automatically starts.
10.
ATTENTION
The system is restarted and the scan­ner will be detected.
Do not remove the Setup CD-ROM until the PC is restarted completely.
Depending on the OS, the following operations may be necessary.
For Windows 98: When a request for inserting the CD­ROM of Windows 98 appears, insert it into the CD drive and click the [OK] button.
For Windows 2000: When [Digital Signature not Found] appears, click [Yes].
For Windows XP:
1. When [Found New Hardware Wiz­ard] appears, confirm that the Setup CD-ROM is set in the CD drive, then click the [Next] button.
2. When any alarm is displayed on [Hardware Installation] window, click the [Continue Anyway] button.
3. Click the [Finish] button.
Now the installation of the scanner driver is completed.
2-9
Page 26
Installing QuickScan Pro(Trial)
"QuickScan Pro" is an imaging software that complies with the ISIS standards. With the FUJITSU ISIS scanner driver you can capture scanned image data read with the scanner.
When using Windows NT 4.0, Windows
ATTENTION
Insert the Setup CD-ROM into the CD
1.
drive.
The <SETUP DISK STARTUP SCREEN> will be displayed.
Click [Install Products].
2.
2000 and/or Windows XP, please login as a user with "Administrator" privileges (privileges of the administrator of your PC).
Install the application following the
4.
instructions on the window.
Input the requested information and
5.
click on the [Next] button.
Click the [QuickScan PRO (trial)]
3.
button in the following screen.
QuickScan Pro, attached to the Setup
ATTENTION
Install the application following the
6.
instructions on the window.
CD-ROM is a trial version. Therefore, there is a limitation of 30 program starts. Purchasing this software is necessary if you intent to use this software unlimited. (when installing and using the trial version, please use the displayed serial number. For the operations of QuickScan, please refer to the "Overview of QuickScan" or the "QuickScan Help". Please click [Start], [Program], and then [QuickScan] in turn, and select then the file to refer.
Confirming the installation
Please confirm if the scanner operates correctly with the following procedure.
2-10
Page 27
Load the documents on the scanner.
1.
For loading documents, please refer to Chapter 2 "BASIC SCANNER OPERATIONS" of the "fi-5750C Operator's Guide".
Start QuickScan Pro.
2.
Please select [Start], [Programs], [QuickScan] in turn, then click on [QuickScan].
Select [Scan], and [Select
3.
Scanner...] from the menu bar.
Select Fujitsu fi-5750C, then click the [OK] button.
Select [Preview Scan] from the [Scan]
5.
menu to start the scanning-
If the scanning is completed without any troubles, the installation was performed successfully.
Select [Preview Setting...] from the
4.
[Scan] menu. Set the reading resolution and document size, then click [OK].
-
-
-
HINT
Refer to "QuickScan Overview" or "Quick Scan Help" for information about Quick
ScanTM functions and operations. On the [Start] menu, point to [Programs] - [Quick Scan] and click the file.
2.3.3 Installing other application programs
Installing Error Recovery Guide
If you did not install the Error recovery guide together with the driver, please follow the below given procedure for installing it separately. When Error Recovery Guide is installed on your PC, it displays troubleshooting informa­tion on screen if any scanner error occurred.
Insert the Setup CD-ROM in your CD
1.
drive.
The <SETUP DISK STARTUP SCREEN> will be displayed.
2-11
Page 28
Click [Install Products].
2.
Click [Error Recovery Guide] in the fol-
3.
lowing screen.
When the [InstallShield Wizard
6.
Complete] screen is displayed, click [Finish].
Installing the Image processing software option (trial version)
For the installation of the image processing software option (trial version), please refer to the "Image Processing Software Option User's Guide".
Select a language to use for the installa-
4.
tion in the <Choose Setup Language> window and click [OK].
Install the application following the
5.
instructions on the window.
Installing Adobe Acrobat
Install Adobe Acrobat from the "Adobe Acro­bat 6.0 CD-ROM" provided with this scanner.
Adobe Acrobat 6.0 Standard is not
ATTENTION
HINT
Insert the Adobe Acrobat 6.0 CD-ROM
1.
into your CD-ROM drive.
The CD-ROM is automatically recognized and the "Adobe Acrobat6.0 AutoPlay" screen will be displayed.
supported by Microsoft Windows 95, Microsoft Windows NT4.0, Microsoft Windows 98, Microsoft Windows Me. (Except for Microsoft Windows 98 Second Edition.) To use Acrobat 6.0 with FUJITSU scanners, FUJITSU TWAIN32 Scanner Driver Version 8.11.32 or later, or Version
9.11.32 or later is required.
Adobe Acrobat is required for displaying the manuals stored on the CD-ROM. * The installation of Adobe Acrobat 6.0 is not necessary if it is already installed on your PC.
2-12
Page 29
The <Adobe Acrobat 6.0 AutoPlay>
ATTENTION
Click the [Install] button when the
2.
screen may not appear when the “Autoplay” setting of your PC is turned off. In this case, run" AutoPlay.exe" on the CD-ROM directly from the explorer or "My Computer".
following screen is displayed. Then click the [Install Acrobat 6.0 Standard] button.
ATTENTION
Support and User registration for Adobe products
For details, refer to the technical support information stored in the [Customer Support] folder on Adobe Acrobat 6.0 Standard CD-ROM. (Note that free person-to-person support is not available for this is bundled product.)
Click the [Next] button when the
3.
following screen is displayed.
The installation is started and its setup screen is displayed.
After the setup screen is displayed, fol-
4.
low the instructions on the screen to perform the installing.
For more detailed information about the
HINT
Adobe Acrobat 6.0 installation, please read "Read me" displayed at the screen of operation 2. For the operations of Adobe Acrobat 6.0, please refer to the "Adobe Acrobat 6.0 help".
2-13
Page 30
2-14
Page 31

Appendix

Appendix 1 Troubleshooting .......................... AP-2
Appendix 2 Daily Care ................................... AP-6
Appendix 3 Replacing Consumables ............ AP-8
Appendix 4 Setting the position of the ADF ... AP-9
AP-1
Page 32

Appendix 1 Troubleshooting

Before you ask for repair service, check the following items. If the problem persists even after implementing remedies below, contact the dealer where your purchased the or an authorized FUJITSU service provider.
Troubleshooting checklist
TABL E 1.
Symptom Check this Item Remedy
Scanner cannot be tuned ON.
Scanning does not start. Are the documents loaded
Vertical lines appear in the printed images.
The printed scanned image shifts or is dis­torted.
Did you push the power switch? Push the power switch. Is AC cable connected correctly? Correctly connect the AC cable.
Disconnect the AC cable from the scanner, then connect it again.
If this does not restore
the power supply, contact the dealer where you purchased the scanner or an authorized FUJITSU scanner service provider.
Is Windows normally started up? Push the power switch again after completely
Is the shipping lock unlocked? Unlock the shipping lock.
correctly on the ADF paper chute? Is the ADF closed completely? Close the ADF completely. Is USB or SCSI cable connected
correctly? Is the SCSI ID set correctly?
(When using SCSI interface) Does the Function No. display
indicates an alarm or an error?
Does the alarm state remain displayed even after the scanner has been turned OFF and back ON again?
(When using the Flatbed) Are the glass and document holding pad dirty?
(When using the ADF) Is the glass inside the ADF dirty?
(When using the Flatbed) Are the glass and document holding pad dirty?
(When using the Flatbed) Is the document holding pad dirty?
(When using the ADF) Is the ADF cover pressed down or heavy object placed on the ADF during scanning?
(When using the ADF) Is something causing the scanner to vibrate during scanning?
starting up Windows.
Load the document correctly on ADF paper chute.
Correctly connect the cable. (When a USB hub is used, check the hub’s power supply.)
Set the SCSI ID correctly using SCSI ID switch on the rear of the scanner.
When the Function No. display indicates an alarm or an error, refer to "6 TROUBLE SHOOTING" in the "fi-5750C Operator's Guide".
Turn OFF and ON the scanner. If this does not eliminate the alarm state, contact
the dealer where you purchased the scanner or an authorized FUJITSU service provider.
Clean the glass and document holding pad following the instructions in "4.3 Cleaning Flatbed" of the "fi-5750C Operator's Guide".
Clean the glass following the instruction in “4.2 Cleaning ADF” of the “fi-5750C Operator’s Guide”.
Clean the glass and document holding pad following the instructions in "4.3 Cleaning Flatbed" of the "fi-5750C Operator's Guide".
Install the document holding pad correctly.
Do not press down the ADF nor place heavy objects on the ADF during scanning.
Do not allow anything to cause the scanner to vibrate while scanning.
AP-2
Page 33
TABL E 1.
Symptom Check this Item Remedy
The printed scanned image shifts or is dis-
Are the documents loaded correctly?
Load the documents correctly.
torted. Quality of scanned
images is unsatisfac­tory.
(When using the Flatbed) Is the document holding pad dirty?
(When using the ADF) Is the glass inside the ADF dirty?
Install the document holding pad correctly.
Clean the glass following the instruction in “4.2 Cleaning ADF” of the “fi-5750C Operator’s Guide”.
Double feeds occur fre­quently.
Do the documents qualify the "Document Quality" and "Double­feed Detection Condition" in "8 DOCUMENT SPECIFICATON
Use the documents that qualify the "Document Quality" and "Double-feed Detection Condition" in "8 DOCUMENT SPECIFICATON FOR THE
ADF" of the "fi-5750C Operator's Guide". FOR THE ADF" of the "fi-5750C Operator's Guide" fi-5750C?
Are the documents set properly on the ADF paper chute?
Fan the documents before scanning. Correctly
align the document stack and load them on the
ADF paper chute. For details, refer to "2 BASIC
SCANNER OPERATIONS" of the "fi-5750C
Operator's Guide". Is the document stack thicker
than: 20mm? (for A4 size paper) 10mm? (for A3 size paper)
Reduce the number of sheets in the document
stack to 20mm (for A4 size paper) or 10mm (for
A3 size paper) thickness or less. Is the Brake roller dirty? Clean the Brake roller. For details, refer to "4
DAILY CARE OF THE EQUIPMENT" of the "fi-
5750C Operator's Guide" Is the Brake roller worn out? Replace the Brake roller. For details, refer to "5
REPLACING CONSUMABLES" of the "fi-
5750C Operator's Guide"
Documents are not fed into the ADF (pick error occurs frequently or the document stops midway).
Do the documents qualify the "Document Quality" and "Double­feed Detection Condition" in "8 DOCUMENT SPECIFICATON FOR THE ADF" of the "fi-5750C
Use the documents that qualify the "Document
Quality" and "Double-feed Detection Condition"
in "8 DOCUMENT SPECIFICATON FOR THE
ADF" of the "fi-5750C Operator's Guide".
Operator's Guide"? Is the Pick roller set dirty? Clean the Pick roller set. For details, refer to 4.2
"Cleaning the ADF" of the "fi-5750C Operator's
Guide". Is the Pick roller set worn? Replace the Pick roller set. For details, refer to 5.3
"Replacing the pick roller set" of the "fi-5750C
Operator's Guide". Is there any debris on the
Remove any debris from the document feed path. document feed path?
The scanned images are elongated.
Are the Feed rollers dirty? Clean the Feed rollers. For details, refer to the "fi-
5750C Operator's Guide". Did you adjust the scan scale? For Windows 98, Windows Me, Windows 2000
and Windows XP, please select [Scanner and
Camera] in the [Control Panel], then click [Device
Set] tab to adjust the scan scale.
For Windows 95 and Windows NT 4.0, right-click
Scanner Control Center icon in task tray, select
[Option] and adjust the scan scale. Please refer to
“7 Online Setup” of the “fi-5750 Operator's
Guide” and adjust the offset from the Software
Operation Panel (online settings).
AP-3
Page 34
TABL E 1.
Symptom Check this Item Remedy
There is a shadow on
Are the Feed rollers dirty? Clean the Feed roller. For details, refer to "4
the leading edge of the scanned images.
Adjust the offset. For Windows 98, Windows Me, Windows 2000
DAILY CARE OF THE EQUIPMENT" of the "fi-
5750C Operator's Guide"
and Windows XP, adjust the [Sub-scan Setting\
on] Scanners and Cameras\ in the [Control Panel].
For Windows 95 and Windows NT 4.0, right-click
the Scanner Control Center icon, select [Options] -
[Sub-scan Setting] and adjust the offset. Please
refer to Chapter 7 “Online Setup” of the “fi-5750
Operator's Guide” and adjust the offset from the
Software Operation Panel (online settings).
AP-4
Page 35
Temporary Error
TAB L E 2.
Indication Meaning
U0 Confirm that the shipping lock
U1 A paper feed error occurred. U2 A double feed error occurred. U4 The ADF cover is opened.
is released.
The following shows the procedure for resolv­ing of each temporary error.
"U0" error
Release the shipping lock. For releasing the shipping lock, refer to 2.1 “Installing the Scanner” in this manual.
"U1" error Remove jammed documents.
Confirm that the documents meet the paper conditions for scanning. Refer to Chapter 6 "TROUBLE SHOOTING" in the "fi-5750C Operator's Guide".
"U2 " error Remove jammed documents Confirm that the documents meet the paper
conditions for scanning. Refer to "8 DOCUMENT SPECIFICATION OF ADF" of the "fi-5750C Operator's Guide".
"U4" error
Close the ADF cover completely. For details, refer to “6 TROUBLESHOOTING” in the “fi-5750C Operator’s Guide”.
Device alarm (Permanent error)
When you encounter any alarm, turn OFF and ON the scanner. If the alarm is still displayed on the Function No. display, contact the dealer where you purchased the scanner or an authorized FUJITSU scanner service provider.
TABLE 3.
Indication Meaning
E0 Flatbed motor malfunction. E1 Optical error (Flatbed). E2 Optical error (ADF front). E3 Optical error (ADF back). E4 Motor fuse malfunction. E5 Lamp fuse malfunction. E6 Operator panel malfunction. E7 EEPROM malfunction. E8 SCSI interface fuse
E9 Image memory malfunction. Ec Memory malfunction. Ed Malfunction at SCSI interface
EF Background switching
E10 ROM malfunction. E11 Fan malfunction. E12 Heater malfunction. E15 Malfunction in the additional
E16 Option board malfunction. E18 Sensor malfunction. E19 LSI malfunction. E1A Internal communication
HINT
malfunction.
controller.
malfunction.
memory option.
malfunction.
About Error Recovery Guide
When this software is installed on your PC, the icon appears in the task tray when Windows is started up. If any device alarm or temporary error occurred, the Error Recovery Guide win­dow appears and displays information such as error names and error codes regarding the alarm. Record the informa­tion and click [Details...] to know more detailed information for trouble shooting.
AP-5
Page 36

Appendix 2 Daily Care

The glass of the inside of the ADF becomes hot during operation.
CAUTION
When you clean the inside of the scanner, turn OFF the power and unplug the AC cable from the outlet and wait for at least three minutes.
Do not turn OFF the scanner when you clean the Feed rollers and Plastic Rollers.
Cleaning Materials
Cleaning Materials Parts No. Remarks
Cleaner F1 CA99501-0013 1 bottle.
Cleaner F2 CA99501-0014 1 bottle.
TABLE 4.
Moisten a cloth with this fluid and wipe the respective areas. *1
Moisten a cotton swab with this fluid and clean the respective areas. *1
Cleaning Paper CA99501-0012 10 sheets / package. Moisten a
Lint-free dry cloth Commercially available one.
*1) For details on the cleaning materials, contact the FUJITSU scanner dealer where you purchased the scanner.
Do not clean the rubber rollers with Cleaner F2.
Cleaning Paper with Cleaner F1 and insert it into the ADF. *1
CAUTION
AP-6
Page 37
Locations and Cycle for Cleaning
TABLE 5.
Part to Clean
Flat Bed Document Holding Pad
Document Bed
ADF Chute Roller
Pick Arm
Pick Roller Set
Brake Roller
Feed Rollers
Plastic Rollers
Sheet Guide
Glass
Standard Cleaning Cycle using Cleaner F1
Clean these parts after every 10,000 scans.
Standard Cleaning Cycle using Cleaning Paper with Cleaner F1
Clean these parts after every 10,000 scans.
Standard Cleaning Cycle using Cleaner F2
Clean these parts when dirty.
3 3 3 3 33 33 33 333 33 3
Ultra Sonic Sensor Clean this part with a dry lint-free dry cloth.
For details on the cleaning the ADF, refer to Chapter 4 "DAILY CARE OF THE EQUIPMENT" of the "fi-5750C Operator Guide".
ATTENTION
The scanner must be cleaned more frequently if you scan any of the following type of documents.
Documents of coated paper.
Documents that are almost completely covered with printed text or graphics.
Chemically treated documents such as carbonless paper
Documents containing a large amount of calcium carbonate
Handwritten documents
AP-7
Page 38
Appendix 3 Replacing
Consumables
of the used paper and how frequently the scanner is used and cleaned.
ATTENTION
Use only the specified consumables.
The glass of the inside of the
CAUTION
ADF becomes hot during opera­tion.
When you clean the inside of the scanner, turn OFF the power and unplug the AC cable from the outlet and wait for at least three minutes.
Consumables and Replacement Cycle
The following table shows the specifications of consumables and guidelines for the replacement cycle.
TABLE 6.
Standard
Description Part No.
Brake Roller
Pick Roller* PA03338-K011 After 250,000
PA03338-K010
Replacement Cycle
After 250,000 scans or one year.
scans or one year.
Do not use other consumables.
The following pictures shows the locations of the parts to be replaced. Refer to "Chapter 4 Replacing Consumables" fi-5750C Operator's Guide on User Manual CD-ROM.
Pick Roller Set
Brake Roller
* A set of two rollers.
For purchase of consumables, contact the store where you purchased the scanner or an autho­rized FUJITSU scanner service provider.
The replacement cycles above are rough guidelines for the case of using A4/Letter woodfree or wood containing paper 64 g/m2 (17 lb). This cycle varies according to the type
AP-8
Page 39
Appendix 4 Setting the
position of the ADF
As the factory default, ADF of fi-5750C is fixed with ADF lock screws. Be sure to remove the screws before changing the position of the ADF.
ADF can be set to the following three posi­tions:
Type 1: Traditional
-Traditional style of previous FUJITSU scanner products
-For operators accustomed to previous FUJITSU scanners
Type 2: Standard
- Small foot print
- For right-handed operators
- For left-handed operators
Type 2 and 3 are available only when the ADF is set to the center position. Before changing the ADF position to Type 2 or 3, slide the ADF to the center position. When the ADF is in Type 2 position, you can change the position to Type 3 by rotating the ADF in 180 degrees and vice versa.
For details on setting the ADF, refer to 2.2 “Setting the ADF” of “fi-5750C Operator’s Guide” on Manual CD-ROM.
Type 3: Reversed
- Small foot print
CAUTION
ATTENTION
Take care not to pinch your fingers when rotating the ADF.
• Please rotate the ADF after you set the stacker upright.
• When you change the position of the ADF, do not rotate it over 180 degrees, other wise the ADF may be damaged.
AP-9
Page 40
AP-10
Page 41
fi-5750C Image Scanner Getting Started
P3PC-E737-01EN
Date of issuance: December, 2003
Issuance responsibility: PFU LIMITED
Printed in Singapore
z Copying of the contents of this manual in whole or in part and copying of the scanner
application is forbidden under the copyright law.
z The contents of this manual are subject to change without notice. z PFU LIMITED is not liable whatsoever for any damages resulting from use of this scan-
ner and procedures described in this manual, profit loss due to defects, and any claims by a third party.
Page 42
Loading...