Fujitsu P55XHA40W, P42HHA40U, P42VHA40R, P42VHA40W, P50XHA40U User Manual

...

Download

USER'S MANUAL

(Specification and Part Names)

WIDE PLASMA DISPLAY

P42VHA40W/P42HHA40W/P50XHA40W/P55XHA40W/

P63XHA40W

P42VHA40U/P42HHA40U/P50XHA40U/P55XHA40U/

P63XHA40U

P42VHA40A/P42HHA40A/P50XHA40A/P55XHA40A/

P63XHA40A

P42VHA40R/P63XHA40R

EnglishDeutschEspañolFrançaisItalianoPortuguês

Contents

Page

Before Use

• CHECKING ACCESSORIES .................................................................................... E-2

• INSTALLATION ........................................................................................................ E-3

Usage

• PART NAMES AND FUNCTIONS ............................................................................ E-4

Others

• OPTIONS.................................................................................................................. E-9

• MAIN SUPPORTED SIGNALS............................................................................... E-10

• SPECIFICATION .................................................................................................... E-12

Before using the display, read the User’s manual (1/2) and the User’s manual (2/2) carefully so that you know how to use the display correctly. Refer to this manual whenever questions or problems about operation arise. Be sure to read and observe the safety precautions (see the separate "Safety Precautions" manual). Keep this manual where the user can see it easily. * Installation and removal require special expertise. Consult your product dealer for details. * When "English" is selected at "Language" of the on-screen display, "colour" will be displayed in the case of the R model and "color"

will be displayed for all other models.

The notation used in this users' manual is "color". * All operation items of A model are the same as W model. Please read the description part of "W model" for "A model" in User's manual (2/2). * The residential warranty for "A model" is enclosed in accessories. * The last digit of MODEL NO. (10 digit alphanumeric characters) indicated on the product means the body color indication alphabet or

the management number. * The illustration of external appearance is for 42" model.

Please acknowledge some differences in the actual product of other models.

Póññêèé

÷–Œƒ

日本語

CHECKING ACCESSORIES

One power cable Two small

ferrite cores

No.:ZCAT1518-0730 Mfr.:TDK

Two AA batteries One residential

Two big

ferrite cores

No.:SFT-72SN Mfr.:TKK

warranty

(for the A model)

Three user's manuals

Manual

One remote control (for the W/A/R models)

CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT

One remote control

(for the U model)

Carefully check the terminals for position and type before making any connections.

Loose connectors can result in picture or color problems. Make sure that all connectors are securely inserted into their terminals.

Ferrite cores

These ferrite cores are used to attenuate undesired signals.

Two big ferrite cores

When connecting a cable to the power input terminal, video input terminal, attach one of these ferrite cores to the cable near the terminal.

Power Cable

Ferrite Core

RCA Video Cable

Ferrite Core

Two small ferrite cores

When connecting a cable to the external speaker output terminal attach one of these ferrite cores to the cable near the terminal.

E-2

Ferrite Core

INSTALLATION

To prevent the display's internal components from overheating, make sure that the display is installed in a well-ventilated location.

Be sure to use the optional stand, wall-mounting unit or the other unit when installing the display. Also, be also sure that your dealer performs the installation.

See the appropriate instruction manual for more information on the installation hardware you select.

To prevent an accident and ensure safety in the event of an earthquake, fix the display securely into position as described below.

To ensure proper heat radiation, provide at least as much space around the display as shown below.

* Make sure that the display is installed in a location where the temperature can be maintained between 0°C and 40°C.

* Never attempt to tilt the display sideways or backward.

* To prevent the power and other cables from being accidentally pulled, make sure that they run along the wall or through corners.

* To prevent accidents and ensure safety in the event of an earthquake, secure the display to prevent it from tipping over.

Display Section

Front Side

Upper

(cm)

EnglishDeutschEspañolFrançaisItalianoPortuguês

Left

Lower

Right

3.5 (for 42”/50”) 5 (for 55”/63”)

Wall

Póññêèé

Note

The display is a highly precise piece of equipment and therefore must be packed properly before transportation. Be sure to use only those packing materials originally supplied with the display when repacking it.

Reference

See P. E-9 for more information on options.

÷–Œƒ

日本語

E-3

PART NAMES AND FUNCTIONS

DISPLAY SECTION – FRONT

(Right section)

 Power indicator lamp

This lamp shows the state of the power supply.

Lit (red): Stand-by state

Lit (green): Power ON state

Flashing (red or green): Malfunction (Flashes differently

depending on the type of malfunction.)

 Remote control signal receiver

Receives signals from the remote control.

 Input mode selector button [MODE]

 Input mode selector button [MODE]

Switches between picture input modes.

 VOL + button

 VOL - button

Adjusts the audio volume.

 Wide screen selector button [WIDE]

Switches the screen over to a desired wide screen.

 ON/OFF button

Turns the power "ON" and "OFF (standby state)".

 Ambient Sensor

Detects the brightness of external light. Do not obstruct it.

Warning

If the power indicator lamp flashes red or green, this signifies that the display has developed a problem. When this happens, be sure to remove the power plug from the receptacle and contact your dealer. Leaving the display power ON can result in fire or electric shock.

E-4

DISPLAY SECTION – BACK AND BOTTOM PART

EnglishDeutschEspañolFrançaisItalianoPortuguês

Back

 / I power switch

If this button is pressed when the power indicator lamp is off, the indicator lamp will light.

The power can be turned on and the standby mode selected by using the remote control or the control panel of the display.

If this button is pressed when the power indicator lamp is lit, the indicator lamp will go out.

*Power is still supplied to parts of the display even if the indicator lamp is off.

 HDMI input terminal (VIDEO5 INPUT/HDMI) for the U model

Connect this terminal to the HDMI output terminal for DVD, etc.

 RS-232C terminal (RS-232C)

This terminal is provided for you to control the display from the PC. Connect it to the RS-232C terminal on the PC.

 RGB1 input terminal (RGB1 INPUT/DVI-D) for the W/U/A models

Connect this terminal to the PC’s display (digital RGB) output terminal.

*The connection cable No.88741-8000 made by molex Inc. is recommanded.

Bottom

Póññêèé

÷–Œƒ

Note

• The illustration of external appearance is for 42" model. Please acknowledge some differences in the actual product of other models.

日本語

E-5

PART NAMES AND FUNCTIONS (Continued)

 RGB2 input terminal (RGB2 INPUT/mD-sub) for the W/U/A models /

RGB1 input terminal (RGB1 INPUT/mD-sub) for the R model

Connect this terminal to the PC’s display (analog RGB) output terminal or decoder (digital broadcast tuner, etc.) output terminal.

 Component video input terminal (VIDEO3 INPUT)

 Component video input terminal (VIDEO4 INPUT)

Connect this terminal to the component video output (color difference output) terminal of your HDTV unit or DVD player.

 Video input terminal (VIDEO1 INPUT)

Connect this terminal to the video output terminal of your VCR. When connecting a cable, attach a ferrite core to the cable. (See P. E-2.)

 S-Video input terminal (VIDEO2 INPUT)

Connect this terminal to the S-video output terminal of your VCR.

 Audio3 input terminal (AUDIO3 INPUT)

 Audio2 input terminal (AUDIO2 INPUT)

 Audio1 input terminal (AUDIO1 INPUT)

Connect this terminal to the audio output terminal of your VCR, etc. (See the User’s manual (2/2) for the selection of audio input for video input.)

 External speaker output terminal (EXT SP)

Connect this terminal to the optionally available speaker. When connecting a cable, attach a ferrite core to the cable. (See P. E-2.)

* See the speaker instruction manual for more information.

 Power input terminal

Connect this terminal to the power cable supplied with the display. When connecting a cable, attach a ferrite core to the cable. (See P. E-2.)

E-6

DESCRIPTION OF INPUT TERMINALS

EnglishDeutschEspañolFrançaisItalianoPortuguês

DVI-D terminal (RGB1 INPUT/DVI-D) for the W/U/A models

mD-sub input terminal (RGB2 INPUT/mD-sub) for the W/U/A models (RGB1 INPUT/mD-sub) for the R model

Pin No. Signal Pin No. Signal Pin No. Signal

1 T.M.D.S. Data2– 9 T.M.D.S. Data1– 17 T.M.D.S. Data0–

2 T.M.D.S. Data2+ 10 T.M.D.S. Data1+ 18 T.M.D.S. Data0+

4— 12— 20—

5— 13— 21—

6 DDC Clock 14 +5V Power 22

7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock+

8 — 16 Hot Ploug Detect 24 T.M.D.S. Clock–

Pin No. Input signal Pin No. Input signal

1Red 9—

2 Green 10 Ground

3Blue 11—

4— 12—

5 Ground 13 Horizontal synchronization

6 Ground 14 Vertical synchronization

7 Ground 15 —

8 Ground Frame Ground

T.M.D.S. Data2 Shield

T.M.D.S. Data1 Shield

T.M.D.S. Data0 Shield

T.M.D.S. Clock Shield

RS-232C terminal (RS-232C)

Pin No. Signal

1 DCD (Data Carrier Detect)

2 RD (Received Data)

3 TD (Transmit Data)

4 DTR (Data Terminal ready)

5 GND (Ground)

6 DSR (Data Set Ready)

7 RTS (Request To send)

8 CTS (Clear To Send)

9 RI (Ring Indication)

Póññêèé

÷–Œƒ

日本語

E-7

PART NAMES AND FUNCTIONS (Continued)

HDMI input terminal (VIDEO5 INPUT/HDMI) for the U model

HDMI (High-Definition Multimedia Interface)

HDMI is a standard for home digital interfaces, which can transmit images as well as multichannel audio signals and control signals through one cable.

Pin No. Input signal Pin No. Input signal

1 T.M.D.S. Data2+ 11 T.M.D.S. Clock Shield

2 T.M.D.S. Data2 Shield 12 T.M.D.S. Clock–

3 T.M.D.S. Data2– 13 CEC

4 T.M.D.S. Data1+ 14 Reserve

5 T.M.D.S. Data1 Shield 15 DDC Clock

6 T.M.D.S. Data1– 16 DDC Data

7 T.M.D.S. Data0+ 17 Ground (for +5V)

8 T.M.D.S. Data0 Shield 18 +5V Power

9 T.M.D.S. Data0– 19 Hot Plug Detect

10 T.M.D.S. Clock+ Frame FG

E-8

OPTIONS

Wall-mounting Bracket 0° to 15° mounting angle P-WB4201 (for 42” model/50” model)

P-WB6300 (for 55” model/63” model)

Ceiling unit 0° to 15° mounting angle P-CT4200 (for 42” model/50” model)

P-CT6300 (for 55” model/63” model)

Desktop Stand unit P-TT4202 (for 42” model/50” model/55”

model)

P-TT6300 (for 63” model)

EnglishDeutschEspañolFrançaisItalianoPortuguês

Speaker (1 set of 2 speakers)

Desktop Speaker Stand (1 set of 2 speaker stands)

* When installing an option, make sure that all installation requirements for that option (as given in the relevant instruction manual) are met.

* The colors of options do not match the display colors perfectly.

* To improve the function and performance of optional accessories, specifications and part names may change. Consult your local dealer

before purchasing.

Warning

To prevent injury, fire, and electric shock, arrange for options to be initially installed (or installed at a different location) by your dealer.

P-SP1000 (for attaching to the display) for 42” model/50” model

P-SP5010 (for attaching to the display) for 55” model

P-SP6300 (for attaching to the display) for 63” model

P-SP4200 (for mounting on the speaker stands) for 42” model

P-SP5010 (for mounting on the speaker stands) for 50” model/55” model P-ST4200 (for P-SP4200)

P-ST5000 (for P-SP5010)

Póññêèé

÷–Œƒ

CAUTION

This display (P42VHA40/P42HHA40/P50XHA40) is for use only with Fujitsu General Limited's option (P-WB4201, P-CT4200, P-TT4202). This display (P55XHA40) is for use only with Fujitsu General Limited's option (P-WB6300, P-CT6300, P-TT4202). This display (P63XHA40) is for use only with Fujitsu General Limited's option (P-WB6300, P-CT6300, P-TT6300). Using this display with other option can cause instability resulting in possible injury.

日本語

E-9

MAIN SUPPORTED SIGNALS

This display can store the latest four types of signals for RGB adjustment value. The fifth input signal will replace the adjustment value of the first input signal.

To do this, select a desired signal and follow the instructions in “Adjusting Screen Position and Size” on the User’s manual (2/2) to adjust the parameters.

When you finish, the settings will be automatically stored. Thus, when the display receives that signal, pictures will be displayed in accordance with the settings you most recently selected.

Main corresponding signals (RGB mode)

Display (dots x lines)

640 x 480 31.47 59.94 VGA

640 x 480 37.50 75.00 VGA 75 Hz

640 x 480 43.27 85.01 VGA 85 Hz

720 x 400 31.47 70.09 400 lines

800 x 600 37.88 60.32 SVGA 60 Hz

800 x 600 46.88 75.00 SVGA 75 Hz

800 x 600 53.67 85.06 SVGA 85 Hz

1024 x 768 48.36 60.00 XGA 60 Hz

1024 x 768 60.02 75.03 XGA 75 Hz

1024 x 768 68.68 84.99 XGA 85 Hz

1280 x 1024 63.98 60.02 SXGA 60 Hz

1280 x 1024 79.98 75.03 SXGA 75 Hz

848 x 480 31.02 60.00

852 x 480 31.72 59.97

1360 x 768 47.71 60.01

720 x 485 15.73 59.94 60 fields

720 x 575 15.63 50.00 50 fields

Horizontal frequency (kHz)

Vertical frequency (Hz) Signal DVI-D

※

※It doesn’t support the model with 42” display (displayed pixels 852 x 480 dots x lines).

* In the DVI-D mode, the input signal can be restricted partly.

E-10

In the Comp.video and Video/S-video, the display has been factory-set as follows for different input signals:

Main corresponding signals (Comp.video mode) Main corresponding signals (Video, S-video mode)

Horizontal

frequency (kHz)

15.73 59.94 SDTV 480i 15.73 59.94 NTSC

15.63 50.00 SDTV 576i 15.63 50.00 PAL

31.47 59.94 SDTV 480p 15.63 50.00 SECAM

31.25 50.00 SDTV 576p 15.63 59.52 PAL60

45.00 60.00 HDTV 720p 15.63 50.00 N-PAL

37.50 50.00 HDTV 720p 15.73 59.95 M-PAL

33.75 60.00 HDTV 1080i 15.73 59.94 4.43NTSC

28.13 50.00 HDTV 1080i

Verti cal

frequency (Hz)

Signal HDMI

Horizontal

frequency (kHz)

Ver t ical

frequency (Hz)

Signal

EnglishDeutschEspañolFrançaisItalianoPortuguês

Note

• Depending on the input signal, the display may show pictures of reduced size due to size reduction and interpolation.

• With some input signals, "Out of range" may appear even when the horizontal and vertical frequencies are within their permissible ranges. In this event, match the input signals to another frequency rather than those listed above.

• You can check input signals through "Information" on the FEATURES Menu screen. (See User's Manual (2/2))

• In order to facilitate the explanations, pictures and diagrams in this manual may differ slightly from the actual items.

• All terms (i.e., company and product names) used in this document are trademarks or registered trademarks.

E-11

Póññêèé

÷–Œƒ

日本語

SPECIFICATION

WIDE PLASMA DISPLAY

Model P42VHA40W/A P42HHA40W/A P50XHA40W/A P55XHA40W/A P63XHA40W/A

Screen size

Aspect ratio 16:9 (wide)

Number of pixels 852 (H) x 480 (V) 1024 (H) x 1024 (V) 1366 (H) x 768 (V)

Weight 31.5 kg / 69 lbs 45 kg / 99 lbs 55 kg / 121 lbs 72 kg / 159 lbs

Outer dimensions 103.9 (W) x 64.0 (H) x 8.7 (D) cm

Power supply 110-240 VAC 50/60 Hz

Current rating 3.2-1.35 A 4.2-1.8 A 4.4-1.9 A 5.8-2.3 A 6.8-2.6 A

External equipment terminals

Video input terminals

PC input terminal RGB1 input DVI-D terminal (EIA/CEA-861B Compliant)

Audio terminals 2 audio input pin jacks (L/R) (3 lines)

Control terminal RS-232C connector (D-sub 9-pin)

External speaker output terminal

Operating conditions

Accessories

42" wide screen:

92.1 cm (W) x 51.8 cm (H) (105.7 cm diagonal)

36.3 inch (W) x 20.4 inch (H) (41.6 inch diagonal)

40.9 (W) x 25.2 (H) x 3.4 (D) inch (does not include outer projections)

VIDEO1 INPUT (Video input) RCA terminal 1 Vp-p/75 Ω

VIDEO2 INPUT (S-video input) S terminal Y: 1 Vp-p/75 Ω

VIDEO3/VIDEO4 INPUT 3 RCA terminals Y: 1 Vp-p/75 Ω (Component video input) P

RGB2 input mD-sub, 3 rows, 15-pin

500 mVrms/at least 22 kΩ

Max. output: 10 W + 10 W, 6 Ω

Temperature: 0 to 40 °C / 32 to 104 °F Humidity: 20 to 80 %

3 user's manuals, 1 power cable, 2 small ferrite cores, 2 big ferrite cores, 1 remote control, 2 AA batteries, 1 residential warranty (for the A model)

42" wide screen:

92.2 cm (W) x 52.2 cm (H) (106.0 cm diagonal)

36.3 inch (W) x 20.6 inch (H) (41.7 inch diagonal)

Picture signal: 0.7 Vp-p/75 Ω Synchronization signal:TTL level

50" wide screen:

110.6 cm (W) x 62.2 cm (H) (126.9 cm diagonal)

43.5 inch (W) x 24.5 inch (H) (50 inch diagonal)

121.6 (W) x 72.6 (H) x 10.0 (D) cm

47.9 (W) x 28.6 (H) x 3.9 (D) inch (does not include outer projections)

55" wide screen:

122.9 cm (W) x 69.1 cm (H) (140.0 cm diagonal)

48.4 inch (W) x 27.2 inch (H) (55.1 inch diagonal)

138.0 (W) x 80.8 (H) x 12.5 (D) cm

54.3 (W) x 31.8 (H) x 4.9 (D) inch (does not include outer projections)

C: 0.286 Vp-p/75 Ω

B/CB: 0.7 Vp-p/75 Ω

PR/CR: 0.7 Vp-p/75 Ω

63" wide screen:

139.3 cm (W) x 78.3 cm (H) (159.8 cm diagonal)

54.8 inch (W) x 30.8 inch (H) (62.9 inch diagonal)

150.4 (W) x 89.4 (H) x 12.3 (D) cm

59.2 (W) x 35.2 (H) x 4.8 (D) inch (does not include outer projections)

Regulation

• UL, CSA Safety: UL6500, C-UL EMC: FCC Part 15 Class B, ICES-003 Class B

• CE Safety: EN60065 EMC: EN55022 1998, Class B

EN61000-3-2 1995 EN61000-3-3 1995 EN55024 1998 EN61000-4-2 1995 EN61000-4-3 1996 EN61000-4-4 1995 EN61000-4-5 1995 EN61000-4-6 1996 EN61000-4-8 1993 EN61000-4-11 1994

• AS Safety: IEC60065 EMC: AS/NZS 3548

E-12

WIDE PLASMA DISPLAY

Model P42VHA40U P42HHA40U P50XHA40U P55XHA40U P63XHA40U

Screen size

Aspect ratio 16:9 (wide)

Number of pixels 852 (H) x 480 (V) 1024 (H) x 1024 (V) 1366 (H) x 768 (V)

Weight 31.5 kg / 69 lbs 45 kg / 99 lbs 55 kg / 121 lbs 72 kg / 159 lbs

Outer dimensions 103.9 (W) x 64.0 (H) x 8.7 (D) cm

Power supply 110-240 VAC 50/60 Hz

Current rating 3.2-1.35 A 4.2-1.8 A 4.4-1.9 A 5.8-2.3 A 6.8-2.6 A

External equipment terminals

Video input terminals

PC input terminal RGB1 input DVI-D terminal (EIA/CEA-861B Compliant)

Audio terminals 2 audio input pin jacks (L/R) (3 lines)

Control terminal RS-232C connector (D-sub 9-pin)

External speaker output terminal

Operating conditions

Accessories

Regulation

• UL, CSA Safety: UL6500, C-UL EMC: FCC Part 15 Class B, ICES-003 Class B

• CE Safety: EN60065 EMC: EN55022 1998, Class B

EN61000-3-2 1995 EN61000-3-3 1995 EN55024 1998 EN61000-4-2 1995 EN61000-4-3 1996 EN61000-4-4 1995 EN61000-4-5 1995 EN61000-4-6 1996 EN61000-4-8 1993 EN61000-4-11 1994

• AS Safety: IEC60065 EMC: AS/NZS 3548

42" wide screen:

92.1 cm (W) x 51.8 cm (H) (105.7 cm diagonal)

36.3 inch (W) x 20.4 inch (H) (41.6 inch diagonal)

40.9 (W) x 25.2 (H) x 3.4 (D) inch (does not include outer projections)

VIDEO1 INPUT (Video input) RCA terminal 1 Vp-p/75 Ω

VIDEO2 INPUT (S-video input) S terminal Y: 1 Vp-p/75 Ω

VIDEO3/VIDEO4 INPUT 3 RCA terminals Y: 1 Vp-p/75 Ω (Component video input) P

VIDEO5 INPUT HDMI terminal (HDMI type A connector)

RGB2 input mD-sub, 3 rows, 15-pin

500 mVrms/at least 22 kΩ

Max. output: 10 W + 10 W, 6 Ω

Temperature: 0 to 40 °C / 32 to 104 °F Humidity: 20 to 80 %

3 user's manuals, 1 power cable, 2 small ferrite cores, 2 big ferrite cores, 1 remote control, 2 AA batteries

42" wide screen:

92.2 cm (W) x 52.2 cm (H) (106.0 cm diagonal)

36.3 inch (W) x 20.6 inch (H) (41.7 inch diagonal)

Picture signal: 0.7 Vp-p/75 Ω Synchronization signal:TTL level

50" wide screen:

110.6 cm (W) x 62.2 cm (H) (126.9 cm diagonal)

43.5 inch (W) x 24.5 inch (H) (50 inch diagonal)

121.6 (W) x 72.6 (H) x 10.0 (D) cm

47.9 (W) x 28.6 (H) x 3.9 (D) inch (does not include outer projections)

55" wide screen:

122.9 cm (W) x 69.1 cm (H) (140.0 cm diagonal)

48.4 inch (W) x 27.2 inch (H) (55.1 inch diagonal)

138.0 (W) x 80.8 (H) x 12.5 (D) cm

54.3 (W) x 31.8 (H) x 4.9 (D) inch (does not include outer projections)

C: 0.286 Vp-p/75 Ω

B/CB: 0.7 Vp-p/75 Ω

PR/CR: 0.7 Vp-p/75 Ω

63" wide screen:

139.3 cm (W) x 78.3 cm (H) (159.8 cm diagonal)

54.8 inch (W) x 30.8 inch (H) (62.9 inch diagonal)

150.4 (W) x 89.4 (H) x 12.3 (D) cm

59.2 (W) x 35.2 (H) x 4.8 (D) inch (does not include outer projections)

EnglishDeutschEspañolFrançaisItalianoPortuguês

Póññêèé

÷–Œƒ

Note

• Specifications and external appearance may be change for the sake of improvement.

• Viewing the screen constantly for extended periods can strain your eyes. Be sure to stay at a proper distance (at least 1.6 m or 5.2 feet for 42" / at least

1.9 m or 6.2 feet for 50" / at least 2.1 m or 6.9 feet for 55" / at least 2.4 m or 7.9 feet for 63") from the screen and to look occasionally away while working.

• is a worldwide trademark of Fujitsu General Limited and is a registered trademark in Japan, the U.S.A. and other countries or areas.

E-13

日本語

SPECIFICATION (Continued)

WIDE PLASMA DISPLAY

Model P42VHA40R P63XHA40R

Screen size 42" wide screen:

Aspect ratio 16:9 (wide)

Number of pixels 852 (H) x 480 (V) 1366 (H) x 768 (V)

Weight 31.5 kg / 69 lbs 72 kg / 159 lbs

Outer dimensions 103.9 (W) x 64.0 (H) x 8.7 (D) cm

Power supply 110-240 VAC 50/60 Hz

Current rating 4.2-1.7 A 6.8-2.6 A

External equipment terminals

Video input terminals

PC input terminal RGB1 input mD-sub, 3 rows, 15-pin

Audio terminals 2 audio input pin jacks (L/R) (3 lines)

Control terminal RS-232C connector (D-sub 9-pin)

External speaker output terminal

Operating conditions

Accessories

92.1 cm (W) x 51.8 cm (H) (105.7 cm diagonal)

36.3 inch (W) x 20.4 inch (H) (41.6 inch diagonal)

40.9 (W) x 25.2 (H) x 3.4 (D) inch (does not include outer projections)

VIDEO1 INPUT (Video input) RCA terminal 1 Vp-p/75 Ω

VIDEO2 INPUT (S-video input) S terminal Y: 1 Vp-p/75 Ω

VIDEO3/VIDEO4 INPUT 3 RCA terminals Y: 1 Vp-p/75 Ω (Component video input) P

Picture signal: 0.7 Vp-p/75 Ω Synchronization signal:TTL level

500 mVrms/at least 22 kΩ

Max. output: 10 W + 10 W, 6 Ω

Temperature: 0 to 40 °C / 32 to 104 °F Humidity: 20 to 80 %

3 user's manuals, 1 power cable, 2 small ferrite cores, 2 big ferrite cores, 1 remote control, 2 AA batteries

63" wide screen:

139.3 cm (W) x 78.3 cm (H) (159.8 cm diagonal)

54.8 inch (W) x 30.8 inch (H) (62.9 inch diagonal)

150.4 (W) x 89.4 (H) x 12.3 (D)

59.2 (W) x 35.2 (H) x 4.8 (D) (does not include outer projections)

C: 0.286 Vp-p/75 Ω

B/CB: 0.7 Vp-p/75 Ω

PR/CR: 0.7 Vp-p/75 Ω

inch

Regulation

• CE Safety: EN60065 EMC: EN55022 1998, Class B

EN61000-3-2 1995 EN61000-3-3 1995 EN55024 1998 EN61000-4-2 1995 EN61000-4-3 1996 EN61000-4-4 1995 EN61000-4-5 1995 EN61000-4-6 1996 EN61000-4-8 1993 EN61000-4-11 1994

• AS Safety: IEC60065 EMC: AS/NZS 3548

Note

• Specifications and external appearance may be change for the sake of improvement.

• Viewing the screen constantly for extended periods can strain your eyes. Be sure to stay at a proper distance (at least 1.6 m or 5.2 feet for 42" / at least

1.9 m or 6.2 feet for 50" / at least 2.1 m or 6.9 feet for 55" / at least 2.4 m or 7.9 feet for 63") from the screen and to look occasionally away while working.

• is a worldwide trademark of Fujitsu General Limited and is a registered trademark in Japan, the U.S.A. and other countries or areas.

E-14

USER'S MANUAL

(Precautions and Adjustment Methods)

WIDE PLASMA DISPLAY

EnglishDeutschEspañolFrançaisItalianoPortuguês

Contents

Page Page

Before Use

• INFORMATION ............................................................ E-2

Usage

• USING THE REMOTE CONTROL...............................E-3

• CONNECTING THE DISPLAY TO EXTERNAL

EQUIPMENT ................................................................ E-7

• BASIC OPERATIONS ................................................E-12

• SELECTING INPUT MODE .......................................E-14

• OTHER BASIC OPERATIONS .................................. E-16

• WATCHING PICTURES ON THE WIDE SCREEN.... E-17

Adjustments

• ADJUSTMENT MENU................................................ E-19

• BASIC PROCEDURE OF ADJUSTMENT MENU

OPERATIONS............................................................E-20

• ADJUSTING THE PICTURE ...................................... E-21

• ADJUSTING SCREEN POSITION AND SIZE ...........E-27

• ADJUSTING AUDIO................................................... E-28

"color" will be displayed for all other models. The notation used in this users' manual is "color".

• OTHER ADJUSTMENTS ...........................................E-29

• INITIALIZATION OF USER ADJUSTMENT VALUE ..E-35

Others

• CLEANING AND MAINTENANCE .............................E-36

Pусский

中文

日本語

INFORMATION

• Receptacle

Make sure that the power cable’s grounding wire is grounded.

The display comes with a 3-prong power plug; one prong is connected to the grounding wire. If you have only a 2-hole receptacle, you will need to have it replaced. Contact your dealer for more information.

• Have the display inspected and cleaned by your dealer at regular intervals.

• Pictures may become “burnt” into the screen phosphors if the screen is left on for extended periods. To ensure that the display has a prolonged service life, be sure to use a screen orbiter, white screen. This will ensure the same picture or pattern is not constantly displayed for long periods. (See P. E-33.)

• Extremely high-precision technology has been used in the manufacture of the plasma display panel, with the effective pixel elements exceeding 99.99%. Please be aware, however, that fewer than 0.01% of the pixels may be missing or remain constantly lit.

• Some models are fitted with a radiator fan to prevent the display’s internal temperature from rising during operation. Be careful of the air emitted by the radiator fan, as it may be hot.

• Contact your dealer if you find that the display does not seem to function properly when used with other audio-visual equipment.

You may need to move your display if it produces degraded pictures or noise due to electromagnetic radiation, or if the infrared remote control does not function properly.

• Pictures may not be displayed properly if you connect a non-standard PC to the RGB input terminal. In this case, contact your dealer for more information.

• The protective circuit, built into the display, automatically turns off the power if the display has a problem. In this case, you will see that the power indicator lamp flashes red or green.

Warning

If the power indicator lamp flashes red or green, this signifies that the display has developed a problem. When this happens, be sure to remove the power plug from the receptacle to prevent fire or electric shock. Then contact your dealer.

• Install the display in a location close to a main power supply outlet, and where the emergency stop button can be easily reached.

Note

• Cables for connecting the display to external equipment are not supplied. Contact your dealer for more information on these products.

• In order to facilitate the explanations, pictures and diagrams in this manual may differ slightly from the actual items.

E-2

USING THE REMOTE CONTROL

REMOTE CONTROL (for the W/R models)

For details, see page Î.

  button Î E-12

Switches between Power On and Standby.

- (MUTE button) Î E-13



Temporarily mutes the audio. To return the audio to normal, press this button once again, or press the

2 work also.

 3 (DISPLAY button) Î E-16

Press this button to display the input mode, and screen size status. The status is displayed for about five seconds.



4 (PICTURE MODE button) Î E-16

Use this button to switch the Picture Mode.

 5 (PICTURE MEMORY button) Î E-16

Press this button to recall a Picture Memory.

  (WIDE button) Î E-17

Switches the screen size.

 ) – * (RGB input mode selector button) Î E-15

Selects RGB1 - 2.

 = (RGB3/VIDEO4 imput mode selector button) Î E-14

Selects VIDEO4.

" – $ (Video input mode selector button) Î E-14



Selects VIDEO1 - 3.

 12 (Volume adjustment buttons) Î E-13

Press these buttons to adjust the volume.

; (MENU button) Î E-19–E-35



Press this button to display the menu screen for adjusting the picture and/or the audio.

< (ENTER button) Î E-19–E-35



Press this button to fix the entry in the ADJUSTMENT MENU.

CDEF (Adjustment buttons) Î E-19–E-35

Use these buttons to select the item or adjust the value in the menu screen.

EnglishDeutschEspañolFrançaisItalianoPortuguês

1 does the

Pусский

Note

• Functions may not be available with some models and some device options.

中文

日本語

E-3

USING THE REMOTE CONTROL (Continued)

REMOTE CONTROL (for the U model)

For details, see page Î.

  button Î E-12

Switches between Power On and Standby.

- (MUTE button) Î E-13



Temporarily mutes the audio. To return the audio to normal, press this button once again, or press the

2 work also.

 3 (DISPLAY button) Î E-16

Press this button to display the input mode, and screen size status. The status is displayed for about five seconds.



4 (PICTURE MODE button) Î E-16

Use this button to switch the Picture Mode.

 5 (PICTURE MEMORY button) Î E-16

Press this button to recall a Picture Memory.

  (WIDE button) Î E-17

Switches the screen size.

 " – & (Video input mode selector button) Î E-14

Selects VIDEO1 - 5.

 ) – * (RGB input mode selector button) Î E-15

Selects RGB1 - 2.

12 (Volume adjustment buttons) Î E-13



Press these buttons to adjust the volume.

 ; (MENU button) Î E-19–E-35

Press this button to display the menu screen for adjusting the picture and/or the audio.

< (ENTER button) Î E-19–E-35



Press this button to fix the entry in the ADJUSTMENT MENU.

CDEF (Adjustment buttons) Î E-19–E-35



Use these buttons to select the item or adjust the value in the menu screen.

1 does the

Note

• Functions may not be available with some models and some device options.

E-4

PUTTING BATTERIES IN THE REMOTE CONTROL

EnglishDeutschEspañolFrançaisItalianoPortuguês

(1) To remove the cover, slide it outwards

while pressing it down.

(2) Place two AA batteries in the remote

control. Make sure that the batteries are properly oriented.

(3) Close the cover until it snaps into place.

PRECAUTIONS

To prevent malfunction, be sure not to apply any form of severe shock to the remote control.

To prevent malfunction or deformation, be sure not to allow the remote control to become wet; also, keep it away from hot locations or heating equipment.

Be sure not to clean the remote control using a cloth dampened in any volatile solvent, such as benzene or thinner.

CAUTION

Be sure to use replacement batteries of the same type as the original ones. When disposing of used batteries, please comply with governmental regulations or environmental public institution’s rules that apply in your country/ area.

Note

The remote control will not function properly if the batteries are dead. Be sure to replace them as needed.

Do not use rechargeable batteries (Ni-Cd, etc.).

Pусский

中文

日本語

E-5

USING THE REMOTE CONTROL (Continued)

EFFECTIVE RANGE FOR THE REMOTE CONTROL

Point the remote control at the display’s signal receiver when using it.

Make sure that there are no obstacles between the remote control and the display’s signal receiver.

Upper

20°

Lower

Left

30°

5 m (Front)

30°

Right

Note

The remote control may not function properly if you use a high-frequency fluorescent lamp. If you experience problems, move the lamp or use the remote control from a different position.

E-6

CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT

EXAMPLE OF CONNECTION TO EXTERNAL COMPONENTS

EnglishDeutschEspañolFrançaisItalianoPortuguês

Speaker

VCR or other external components See P. Î

Display

Speaker (optional)

Remote control

To AC outlet

VCR Î E-8

DVD recorder/player Î E-9

Satellite tuner Î E-10

PC Î E-11

Pусский

中文

E-7

日本語

CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)

VCR

• Connect the video signal cable to either the S-video input terminal or the video input terminal.

• If the unit to be connected is equipped with S-video output terminal, it is recommended to connect to the S-video terminal.

To video output

To S-video output

To audio outputs

To audio inputs To video input

To S-video input

Display bottom

E-8

DVD RECORDER/PLAYER

• Connect the video signal cable to the HDMI input terminal, component video input terminal, S-video input terminal, or the video input terminal.

• If the component to be connected is equipped with HDMI output terminal, component video output terminal, it is recommended to connect to the component video terminal.

To component video output

To video output

To S-video output

To audio outputs

To audio inputs To component video input

To video input

To S-video input

EnglishDeutschEspañolFrançaisItalianoPortuguês

Display bottom

To HDMI output

Note

• Unplug the power cord from the AC outlet before you connect external components.

• Also refer to the instructions for the component to be connected.

• When inputting audio, connect to the terminals corresponding to the used video input or RGB input.

• Terminal layout may differ and functions may not be available with some models and some device options.

To HDMI input

Pусский

中文

日本語

E-9

CONNECTING THE DISPLAY TO EXTERNAL EQUIPMENT (Continued)

SATELLITE TUNER

• Connect the video signal cable to the HDMI input terminal, component video input terminal, S-video input terminal, or the video input terminal.

• If the component to be connected is equipped with HDMI output terminal, component video output terminal, it is recommended to connect to the component video terminal.

Antenna (commercially available product)

To audio outputs

To HDMI output

To video output

To S-video output

To component video output

To video input

To S-video input

To audio inputs To component video input

Display bottom

To H D M I i n p u t

E-10

• As the cable for connecting a PC differs with the PC model, please consult your dealer for information on the right cable to purchase.

To RGB output (DVI-D)

To RGB output (mD-sub)

To audio output

To mD-sub input

To audio inputs

To DVI-D input

EnglishDeutschEspañolFrançaisItalianoPortuguês

Display bottom

Note

• Unplug the power cord from the AC outlet before you connect external components.

• Also refer to the instructions for the component to be connected.

• When inputting audio, connect to the terminals corresponding to the used video input or RGB input.

• Terminal layout may differ and functions may not be available with some models and some device options.

Pусский

中文

日本語

E-11

BASIC OPERATIONS

TURNING THE POWER ON AND STAND-BY

Press/I to the left at the bottom of

the display to the ON

The power lamp lights up.

Press  on the remote control.

The color of the power lamp changes from “Red” to “Green”.

Press " – & or ) – *.

Select the video mode to input.

state.

* You can also use the buttons

on the display’s control panel to perform these steps.

(for the W/R models)

Press  when the power is ON.

The color of the power lamp changes from “Green” to “Red” and the the power turns “OFF (Stand-by state)”.

* You can also use the buttons

on the display’s control panel to perform these steps.

(for the U model)

E-12

ADJUSTING THE VOLUME

Adjusting the volume

Press 1 to increase the volume.

2 to reduce the volume.

Press

* Note that the volume level remains stored even when you

turn OFF the power.

EnglishDeutschEspañolFrançaisItalianoPortuguês

* You can also use the buttons

on the display’s control panel to perform these steps.

(Ex. the W model)

Muting the audio

Press -.

The audio is removed.

Press again to restore the audio to the original level.

The mute mode can also be released by pressing the volume buttons.

When the volume adjustment button is pressed

Note

• Functions may not be available with some models and some device options.

Pусский

中文

日本語

E-13

SELECTING INPUT MODE

VIDEO INPUT MODE (for the W/R models)

Press  to select the input mode.

You can select from VIDEO1 mode to VIDEO4 mode.

The video modes corresponding to each input terminal are as follows.

• VIDEO1: Video

• VIDEO2: S-video

• VIDEO3: Component video

• VIDEO4: Component video

* For selection of the input terminal, see

“SETTING THE INPUT TERMINALS” on P. E-31.

Video1 mode

* You can also use the buttons

on the display’s control panel to perform these steps.

VIDEO INPUT MODE (for the U model)

Press  to select the input mode.

You can select from VIDEO1 mode to VIDEO5 mode.

The video modes corresponding to each input terminal are as follows.

• VIDEO1: Video

• VIDEO2: S-video

• VIDEO3: Component video

• VIDEO4: Component video

• VIDEO5: HDMI

* For selection of the input terminal, see

“SETTING THE INPUT TERMINALS” on P. E-31.

Video1 mode

* You can also use the buttons

on the display’s control panel to perform these steps.

E-14

RGB INPUT MODE

Press  to select the input mode.

You can select between the modes from RGB1 to RGB2.

The input terminal of each RGB mode is as follows.

[for the W/U models]

• RGB1: DVI-D

• RGB2: mD-sub

[for the R model]

• RGB1: mD-sub

* For selection of the input terminal, see

“SETTING THE INPUT TERMINALS” on P. E-31.

EnglishDeutschEspañolFrançaisItalianoPortuguês

RGB1 mode

* You can also use the buttons

on the display’s control panel to perform these steps.

(Ex. the U model)

Pусский

E-15

中文

日本語

OTHER BASIC OPERATIONS

CONVENIENT FUNCTIONS

On-screen information

Press 3.

The mode is indicated on the screen for 5 seconds.

Picture Mode

Press 4.

This button can be used to switch the picture mode.

In the picture mode, you can switch between the set status and the fine mode.

* For the picture mode settings, see “Setting Picture Mode (P. E-22)”.

Picture Memory

Press 5.

This button can be used to recall the settings of the picture memories 1 – 8. Each time this button is pressed, the setting changes as follows.

(Ex. the W/R models)

* For the picture memory settings, see “Setting Picture Memory (P. E-22)”.

Note

• Functions may not be available with some models and some device options.

E-16

WATCHING PICTURES ON THE WIDE SCREEN

SWITCHING BETWEEN SCREEN SIZES

Press .

The currently selected mode will appear.

Press  to select a desired Screen Size.

Each time you press , a different Screen Size

appears. The sequences used are as follows:

When you are in a Video input mode

When you are in an RGB input mode

EnglishDeutschEspañolFrançaisItalianoPortuguês

Normal mode

* You can also use the buttons

on the display’s control panel to perform these steps.

(Ex. the W/R models)

* Depending on the type of signal, some aspects

may not be selected.

Wide1 mode

Pусский

Note

• Displaying a picture in a Normal mode for extended periods of time may cause phosphor burn-in.

• A variety of Screen Sizes are available with this display. Remember that if you select a mode with an aspect ratio (ratio of frame width to frame height) different from that of the TV program or video media, the pictures will appear differently than if you had selected a mode having the same aspect ratio.

• Showing a movie or similar premium event at a different aspect ratio from its original one at any event site, restaurant, or bar for profit-making purposes or for a public audience may constitute a copyright infringement. For films, try to select a mode having the same aspect ratio as the original picture; this enables the director’s original intentions to be preserved.

•See P.

E-27 for how to adjust the picture size and position.

中文

日本語

E-17

WATCHING PICTURES ON THE WIDE SCREEN (Continued)

SCREEN SIZE

Normal (Video/RGB)

Displays pictures of normal size (i.e., a 4:3 aspect ratio).

Wide1 (Video)

Displays natural-looking pictures of standard size on the wide screen.

Wide2 (Video)/Wide (RGB)

Ideal for displaying vertically extended pictures such as squeezed pictures.

Zoom1 (Video)/Zoom (RGB)

Enlarges horizontally extended pictures equally in all directions to maintain the aspect ratio constant.

Zoom2 (Video)

Reduces the height of horizontally extended pictures with captions, without eliminating the caption. Only the height of pictures is reduced, not the height of the caption.

(Captions may not be easy to read, however, depending on the picture.)

ASPECT RATIO

The following aspect ratios are available.

Picture of

standard size

Vertically

extended picture

Horizontally

extended picture

Horizontally extended

picture with caption

Wide1

Wide2

Zoom1

Zoom2

4:3 aspect ratio 16:9 aspect ratio (VHF/UHF broadcasting, BS broadcasting) (HDTV broadcasting)

1.85:1 aspect ratio 2.35:1 aspect ratio

(Vista Vision size) (Cinema Vision size)

Note

You may find dark areas on top and at the bottom of the screen if you select one of the Zoom modes for media while using the Vista Vision or Cinema Vision size i.e., the sizes used frequently for picture software.

• Functions may not be available with some models and some device options.

1.85

2.35

E-18

ADJUSTMENT MENU

The numbers in parentheses ( ) indicate the reference page numbers.

PICTURE (E-20) Signal Contrast (E-21)

POSITION/SIZE (E-27) Drive Contrast (E-21)

AUDIO (E-28) Brightness (E-21)

FEATURES (E-29) Color (E-21)

FACTORY DEFAULT(E-35)

Tint (E-21) CODEC NR (E-23)

Sharpness (E-21)

Ambient Sensor (E-21)

Picture Mode (E-22)

PrecisionSetting (E-22) Color Focus (E-25)

Picture Memory (E-22)

Default

Position (E-27)

Size (E-27)

Default

Treble (E-28)

Bass (E-28)

Balance (E-28)

Loudness (E-28)

Adjustment (E-29) Dot Clock (E-29)

On Screen Menu (E-30) Clock Phase (E-29)

Input Terminal (E-31) Clamp Position (E-29)

Others (E-32) Auto Calibration (E-29)

EnglishDeutschEspañolFrançaisItalianoPortuguês

Black Level (E-23)

Detail Gradation (E-23)

3D NR (E-23)

Image Enhance (E-24) Chroma Transient (E-24)

Color Temp. (E-24) Image identify (E-24)

User Color Temp. (E-24)

Progressive Scan (E-26) 24 Frame Mode (E-26)

30 Frame Mode (E-26)

Jaggies Filter (E-26)

Motion Setting (E-26)

OSD (E-30)

Language (E-30)

Name Select (E-30)

Video Input (E-31)

S-video Input (E-31)

D-SUB Input (E-31)

Auto Off-NO SIG. (E-32)

Audio Input (E-32)

Screen Orbiter (E-33)

Direct Setting (E-33)

Code Setting (E-33)

White Screen (E-33)

Exhibition Mode (E-34)

Information (E-34)

Pусский

中文

Note

• The shaded menu items are applied to the U model only.

• Some type of signal can not be selected.

日本語

E-19

BASIC PROCEDURE OF ADJUSTMENT MENU OPERATIONS

• Below is shown the basic procedure to make changes to the options in the ADJUSTMENT MENU. (Ex.: adjusting tint setting (Tint))

Press ;.

The main menu screen will appear.

Press E or F to select “PICTURE”.

Each time you press E or F, one of the available menus appears in the following sequence:

PICTURE < POSITION/SIZE < AUDIO < FEATURES < FACTO RY D EFAU LT

The PICTURE Menu screen will appear.

Press C or D to select “Tint”.

“PICTURE” selected in the main menu screen

Press <.

The “Tint” adjustment screen will appear.

(Ex. the W/R models)

6 7

Press E or F to change tint values.

F: More greenish colors E: More purplish colors

Press < to store.

Press ; when you finish.

* Repeat steps 3, 4, 5 and 6 when you wish to make

changes to other options.

* When

* Press

< is pressed after you have selected

“Default”, the settings are returned to those that were valid when you purchased the set.

; to halt the operation in progress.

“Tint” selected in the PICTURE Menu screen

“Tint” adjustment screen

Note

• On-screen information disappears if you do not take any action for about 60 seconds.

• Functions may not be available with some models and some device options.

• The adjustment range varies with the display signal. You can adjust the display quality to the value you want within the adjustable range.

E-20

ADJUSTING THE PICTURE

• Picture-related items can be set and adjusted in the Picture Adjustment Screen. See BASIC PROCEDURE OF ADJUSTMENT MENU OPERATIONS on page E-20 for the basic operation procedures.

Adjusting the Signal Contrast

Press F to increase the input signal contrast.

Press

E to reduce the input signal contrast.

Press < to store.

Adjusting the Drive Contrast

Press F to raise the display’s luminance level, and increase the contrast. Press E to lower the display’s luminance level, and reduce the contrast. Press < to store.

Adjusting the Brightness

Press F to increase the brightness. Press E to reduce the brightness. Press < to store.

Adjusting Color

Press F to darken the color. Press E to lighten the color. Press < to store.

Adjusting the Tint

Press F to change the tint to a more greenish color. Press E to change the tint to a more purplish color. Press < to store.

Adjusting the Sharpness

Press F to sharpen the Sharpness.

E to soften the Sharpness.

Press

< to store.

Adjusting the Ambient Sensor

Automatically adjusts the Sharpness to an optimized level that matches the brightness of the surrounding area.

Each time

Press

E or F is pressed, the setting is switched.

Off

< to store.

EnglishDeutschEspañolFrançaisItalianoPortuguês

Pусский

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

中文

日本語

E-21

ADJUSTING THE PICTURE (Continued)

Setting Picture Mode

Each time you press E or F , the available choices appear in the following sequence.

[Natural]: Enables you to watch pictures with natural color tones and high picture clarity. This

mode is suitable for watching a normal motion picture.

[Fine]: Suitable for watching a dark picture such as a movie. [Effective]: Displays a screen with detailed contrast. [Conventional]: Displays a screen approximating that of a conventional TV screen. [Still]: Suitable for viewing a still picture.

Press

< to store.

Precision Setting (for the U model)

Enables advanced Sharpness adjustments.

See page E-23 for details.

Setting Picture Memory

The adjustment status of eight groups of picture adjustment settings can be stored, enabling you to quickly switch to your desired group of settings for the picture you are planning to watch.

[Save]: Use values are stored to the selected Memory.

[Load]: Use adjustment values stored in the selected Memory.

C or D to select Memory 1 - 8. If < is pressed, the current picture adjustment

C or D to select Memory 1 - 8. When < is pressed, the values becomes the picture

Picture Memory Selection Screen

“Save” Selection Screen

“Load” Selection Screen

E-22

PRECISION SETTING (for the U model)

• See BASIC PROCEDURE OF ADJUSTMENT MENU OPERATIONS on page E-20.

Even more advanced Sharpness adjustments can be made as required.

Adjusting the Black Level

Press F to strengthen the reproduction of black. (Provides a picture quality with deep blacks.)

Press

E to weaken the reproduction of black.

Press < to store.

Setting Detail Gradation

Corrects the gradation of the light and dark areas of the picture. Each time E or F is pressed, the setting is switched.

On < Off

Press < to store.

Setting 3D NR

This enables noise reduction processing with respect to the input signal noise level (reduces screen flicker for more comfortable viewing).

Each time you press

E or F, the available choices appear in the following sequence.

EnglishDeutschEspañolFrançaisItalianoPortuguês

Precision Setting Selection Screen

< to store.

Press

Setting CODEC NR

This enables noise reduction processing of mosquito noise or block noise generated when digital picture signals are recorded or replayed.

Each time you press

< to store.

Press

E or F, the available choices appear in the following sequence.

Pусский

中文

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

日本語

E-23

ADJUSTING THE PICTURE (Continued)

Setting Image Enhance

This performs detailed image quality settings.

• Chroma Transient

This function corrects the color contours.

Each time

Press < to store.

• Image Identify

This function discerns between the natural image display section and the text display section, and performs correction to enable an optimized display for each.

Each time

Press < to store.

E or F is pressed, the setting is switched.

On < Off

E or F is pressed, the setting is switched.

On < Off

Adjusting the Color Temp.

Use E or F to specify a desired color temperature. Each time you press E or F, one of the available choices appears in the following sequence:

[–3500]: More reddish colors [+3500]: More bluish colors [User]: User Color Temp. setup

Press

< to store.

Setting User Color Temp.

Use C or D to select Red, Green, or Blue, and adjust the color temp. for each.

Press

F: to strengthen the selected color.

Press E: to weaken the selected color.

< to store.

Press

E-24

Setting the Color Focus

This enables correction with respect to specific color hues within the image.

Independent correction of the hue of skin colors, blue skies, and so on, enables a more brilliant display.

• [Reddish color]

With red at the center, performs the following corrections with respect to the range from magenta to yellow.

[Tint]: Use E and F to adjust the hue. [Color]: Use [Red]: Use [Green]: Use [Blue]: Use

Press

Adjustments can be made in the same way for:

• [Greenish color]: (With green at the center, performs corrections with respect to the range from yellow to cyan.)

• [Bluish color]: (With blue at the center, performs corrections with respect to the range from cyan to magenta.)

• [Targeting Red]

This function corrects the hue and color depth with respect to Red.

[Tint]: Use [Color]: Use

Press

Adjustments can be made in the same way for:

• [Targeting Yellow] (Performs correction with respect to Yellow.)

• [Targeting Green] (Performs correction with respect to Green.)

• [Targeting Cyan] (Performs correction with respect to Cyan.)

• [Targeting Blue] (Performs correction with respect to Blue.)

• [Targeting Magenta] (Performs correction with respect to Magenta.)

E and F to adjust the color depth.

E and F to adjust the strength of the red color range.

E and F to adjust the strength of the green color range.

E and F to adjust the strength of the blue color range.

< to store.

E and F to adjust the hue.

E and F to adjust the color depth.

< to store.

Color Focus (Reddish color) Settings Screen

EnglishDeutschEspañolFrançaisItalianoPortuguês

• [Targeting White]

Corrects red, green, and blue with respect to white.

[Red]: Use [Green]: Use [Blue]: Use

Press

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

E and F to adjust Red.

E and F to adjust Green.

E and F to adjust Blue.

< to store.

Pусский

中文

日本語

E-25

ADJUSTING THE PICTURE (Continued)

Making the Progressive Scan Settings

This sets the conversion processing of interlace signals to block receive signals.

• 24 Frame Mode

This function enables the optimized display of movies, etc. with 24 frames/second signals.

Each time

Press < to store.

• 30 Frame Mode

This function enables the optimized display of movies, etc. with 30 frames/second signals. Each time E or F is pressed, the setting is switched.

Press < to store.

• Jaggies Filter

This function alleviates the phenomenon where jagged diagonal lines can be seen when interlace signals are input, thus enabling a smoother motion picture display.

Each time E or F is pressed, the setting is switched.

Press < to store.

E or F is pressed, the setting is switched.

Auto < Off

Progressive Scan Settings Screen

• Motion Setting

The detecting sensitivity for motion picture is set.

The response of the picture processing is valued in the motion picture priority setting.

F: to specify still picture priority.

Press Press E: to specify motion picture priority.

Press

< to store.

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

E-26

ADJUSTING SCREEN POSITION AND SIZE

• You can make changes to all screen adjustment options in the POSITION/SIZE Menu. See Page E-20 for the basic operation procedures.

• The changes you make will be stored for the selected input mode. Therefore, you need to select a desired input mode before making any changes.

Adjusting Screen Position (Position)

Horizontal position (Horizontal)

F: Moves screen to the right.

E: Moves screen to the left.

EnglishDeutschEspañolFrançaisItalianoPortuguês

POSITION/SIZE Menu screen

Vertical position (Vertical)

C: Moves screen up.

D: Moves screen down.

< to store.

Press

Adjusting Screen Size (Size)

Screen width (Width)

F: Increases width.

E: Reduces width.

Screen height (Height)

C: Increases height.

“Position” adjustment screen

Pусский

“Size” adjustment screen

D: Reduces height.

Press < to store.

*You cannot adjust screen size in DVI-D mode.

中文

日本語

E-27

ADJUSTING AUDIO

• You can make changes to all audio adjustment options in the AUDIO Menu. See Page E-20 for the basic operation procedures.

• The changes you make will be stored for the selected input mode. Therefore, you need to select a desired input mode before making any changes.

Adjusting Treble (Treble)

Press EF to make adjustments.

F: Stronger treble E: Weaker treble

Press

< to store.

Adjusting Bass (Bass)

Press EF to make adjustments.

F: Stronger bass E: Weaker bass

Press

< to store.

Adjusting Volume Balance (Balance)

AUDIO Menu screen

Press EF to make adjustments.

F: Shifts the volume balance towards the right. E: Shifts the volume balance towards the left.

Press < to store.

Setting Loudness (Loudness)

Corrects the balance between bass and treble for easy listening even with weak volume.

Each time you press

On < Off

Press < to store.

E or F, one of the available choices appears in the following sequence:

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

• Audio Input menu will not be displayed when “No Audio” is selected. (See P. E-36.)

E-28

OTHER ADJUSTMENTS

• FEATURES setup screen has the following 4 options.

See Page E-20 for the basic operation procedures.

[Adjustment]: Can make a fine adjustment of pictures such as Dot Clock, Clamp Position.

[On Screen Menu]: Can make a display setting such as OSD, Language. (See P. E-30.)

[Input Terminal]: Can make an input terminal setting such as Video Input. (See P. E-31.)

[Others]: Used to make Screen Orbiter and other settings. (See P. E-32–E-34.)

ADJUSTMENT

Dot Clock, Clock Phase, Clamp Position, and Auto Calibration are adjusted as shown in the following chart.

Select the item with

Adjustment Item Contents of Adjustments Operation

Dot Clock (mD-sub)

Clock Phase (mD-sub)

Clamp Position (mD-sub, Comp. video)

Auto Calibration (mD-sub)

CD , and then adjust with E F. Finally, press < to implement the adjustments.

You may find the vertically-striped pattern in pictures, depending on the clock frequency of your PC’s processor. If you experience blurring, you can obtain a clearer picture by adjusting the “Dot Clock”.

Pictures and the outline of letters may blur or flicker as the clock phase of your PC may be different. In this case, adjust the clock phase manually. Normally, the automatic setting ensures the optimal value.

Adjusts the extremely dark or bright pictures. Normally, the automatic setting ensures the optimal value.

Adjusts the dynamic range of images to the optimum. Performed while a white screen signal is received.

Use

E F to adjust to minimize vertically-

striped pattern in pictures.

Use

E F to adjust to minimize pictures blur.

E F to adjust pictures optimally.

Use

Display the Auto Calibration screen and select Execute, and then use item.

CD to select the

EnglishDeutschEspañolFrançaisItalianoPortuguês

E-29

Pусский

中文

日本語

OTHER ADJUSTMENTS (Continued)

ON SCREEN MENU

• Setting Display Information (OSD)

You can use this option to select whether to display information other than menus. (Error messages are displayed regardless of what choice you make for this option.)

Each time you press E or F, one of the available choices appears in the following sequence:

[On (OSD:bright)]: On-screen information shown in light color. [On (OSD:dark)]: On-screen information shown in dark color. [Off]: Except for menus and error messages, on-screen information is not displayed.

Press

< to store.

* When the screen is white [On (OSD:dark)], some of the information may be difficult to read.

• Selecting Language (Language)

You can use this option to select the language displayed on the screen. (1) Select “Language” and press

The “Language” selection screen will appear.

(2) Press

(3) Press

• Selection of indications (Name Select)

You can change the settings for indications for video inputs and RGB inputs.

Video input

You can change the settings for indications for the VIDEO inputs. Select the desired indication in accordance with the connected equipment. Each time

C or D to select your desired language.

English Español (Spanish) Français (French) Português (Portuguese) Русский (Russian) for the R model

The menu is displayed in the selected language.

E F is pressed, the setting is switched. (In the case of VIDEO1)

OSD selection screen

“Language” selection screen (In the case of the W/U model)

Press

< to store.

RGB input

You can change the settings for indications for the RGB inputs. Select the desired indication in accordance with the connected equipment. Each time

Press < to store.

E F is pressed, the setting is switched. (In the case of RGB 1)

E-30

SETTING THE INPUT TERMINALS

• Selecting the settings of Video/S-video Input terminal

You can use this option to select the color format appropriate for the input signal. Each time you press E or F, one of the available modes appears in the following sequence:

[Auto1]: Automatically selects NTSC, PAL and SECAM. [Auto2]: Automatically selects NTSC and M-PAL. [Other than Auto]: You need to select a system appropriate to the input signal.

Press

< to store.

• Selecting the settings of D-SUB Input terminal

You can use this option to select the signal system it will receive to D-SUB Input terminal.

(1) Select D-SUB Input and press

D-SUB Input screen appears.

(2) Select the signal system to receive.

Each time you press E or F, one of the available choices appears in the following sequence:

RGB-PC < Decoder

[RGB-PC]: For using RGB for PC [Decoder]: For using digital broadcast tuner

(3) Press

< to store.

EnglishDeutschEspañolFrançaisItalianoPortuguês

Input Terminal Settings Screen

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

Pусский

中文

日本語

E-31

OTHER ADJUSTMENTS (Continued)

OTHER SETTINGS

Auto Off-NO SIG.

You can make to the standby state automatically when the no signal state continued during set up time.

Press

C D to select the "Time".

Press E F to select the amount of time before the standby state starts.

< to store.

Press

* The numerical value is the approximate amount of time before the standby state starts.

You can assign the black or white color for the background color at the no signal state.

Press

C Dto select the "Background".

Press E F to select the displayed background displayed.

Black < White

Press < to store.

* The background color changes to assigned color state after approximate 20 seconds at the no signal

state.

Auto Off-NO SIG. settings screen

•Selecting input terminals (Audio Input)

You can use this option to select the available terminals to receive the audio from input equipment. (1) Select “Audio Input” and press <.

The “Audio Input” selection screen will appear.

(2) Press C or D to select video input terminal.

(3) Select a related audio input terminal.

Each time you press

[No audio]: No audio in the corresponding mode. [Audio 1-3]: Selects Audio 1 through 3 for receiving audio in the corresponding mode. [Audio 4]: HDMI(for the U model)

* Repeat steps (2) and (3) for each piece of input equipment.

(4) Press

< to store.

* Audio Input menu will not be displayed when “No Audio” is selected.

E or F, one of the available choices appears in the following sequence:

“Audio Input” selection screen (In the case of the U model)

E-32

• Minimizing phosphor burn-in (Screen Orbiter) for RGB

You can use this option to move the screen position to minimize phosphor-induced “burn-in”.

Follow the steps below.

(1) Select “Screen Orbiter” and press

The “Screen Orbiter” setting screen will appear.

(2) Press

(3) Select a desired pattern.

(4) Press

(5) Press

(6) Press

• Setting RGB Input Signal Compulsorily (Direct Setting) for RGB

You can use this option to switch the setting for RGB input signal.

Each time you press

C or D to select “Mode/Time”.

Each time you press E or F, one of the available choices appears in the following sequence:

[Off]: Disables Screen Orbiter. [Time]: Moves the pattern approximately every one hour. [Mode]: Moves the pattern when the power is turned ON or when you switch between modes.

C or D to select “Moving Area”. E or F to select the range for moving the pattern.

Each time you press E or F, one of the available choices appears in the following sequence:

[Min.]: Pattern moves in small range. (About 5 pixels) [Std.]: Pattern moves in moderate range. (About 10 pixels) [Max.]: Pattern moves in wide range. (About 15 pixels)

< to store.

* When the Screen Orbiter function is operated, some letters at the top, bottom, right or left of the

screen may be missed.

E or F, one of the available choices appears in the following sequence:

EnglishDeutschEspañolFrançaisItalianoPortuguês

“Screen Orbiter” setting screen

[Auto]: The optimum display is obtained automatically for input signals. [Others]: The optimum resolution setting is fixed for each signal.

Press < to store.

* In Auto mode, the resolution of VGA, WVGA, 480P, XGA, WXGA, SXGA and SXGA

automatically distinguished. Switch to the fixed display when the image is not displayed properly.

* Signals that are not applicable depending on the model or input terminals may not be displayed.

• Specifying RGB Input Signal (Code Setting) for mD-sub input

Normally, use this option in Auto mode.

• Displaying white over entire screen (White Screen)

You can use this option to display white over the entire screen to minimize phosphor burn-in.

Each time you press

On < Off

Press

< to store.

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

E or F, one of the available choices appears in the following sequence:

may not be

Pусский

中文

日本語

E-33

OTHER ADJUSTMENTS (Continued)

• Setting Exhibition Mode (Exhibition Mode)

You can use this option to display the enhanced contrast, which is most suitable for the use by unspecified persons.

Each time you press

On < Off

Press < to store.

* In Exhibition mode, the display returns to the original setting in about 5 minutes even if the adjustment is changed.

* The setup will be cancelled when removing the power plug from the receptacle.

• Displaying System Status (Information)

Displays system operation status. Select “Information” and press <.

The “Information” screen will appear.

[Mode]: Input mode appears at the upper right corner of the screen

[Freq. Scan Mode]: Frequency scanning

[Input Signal]: Video mode

[Input Sync.]: Signal type

[Freq.]: Synchronized signal frequency, polarity

[Preset No.]: RGB code number

E or F, one of the available choices appears in the following sequence:

Information screen (Video Mode)

Information screen (RGB Mode)

Note

• The screen display disappears if there is no operation within approximately 60 seconds.

• Depending on the model or the optional devices, some of the functions may not be available.

• The adjustment range varies according to the display signals. Make adjustments to your preferred Sharpness within the adjustment range.

• Depending on the type of signal, it may not be possible to make some of the settings or adjustments.

E-34

INITIALIZATION OF USER ADJUSTMENT VALUE

You can restore the values of the adjustment/setting made in the MENU to factory settings.

Press ;.

The main menu screen will appear.

Press E or F to select “FACTORY DEFAULT”.

Each time you press E or F, one of the available menus appears in the following sequence:

PICTURE < POSITION/SIZE < AUDIO < FEATURES < FACTO RY D EFAU LT

The FACTORY DEFAULT Menu screen will appear.

Press <.

“FACTORY DEFAULT” selected in the main menu screen

• Displays the message of whether to proceed with the initialization.

EnglishDeutschEspañolFrançaisItalianoPortuguês

(Ex. the W/R models)

Press C or D to select the Yes.

Displays the message of whether to proceed the initialization

Press <.

• The message of having completed the initialization will be displayed after initializing.

Pусский

Press ; when you finish.

Displays the message of having completed the initialization

E-35

中文

日本語

CLEANING AND MAINTENANCE

Precautions

Be sure to remove the power plug from the receptacle before cleaning the display. Be sure not to clean the display using a cloth dampened with volatile solvents, such as benzene or thinner. Such solvents can harm the display’s cabinet, the filter at the screen front, and the remote control. They can also cause paint to come off these sections.

Cleaning the Screen

Clean the screen gently with a soft cloth. The screen surface is fragile. Never attempt to clean it with a hard material, press on it forcefully, or tap it.

Cleaning the Cabinet and Remote Control

Use a soft cloth for cleaning. If the cabinet or remote control is heavily stained, soak a soft cloth in a mixture of water and detergent and squeeze it dry before wiping off the stains. Use a soft, dry cloth for final cleaning.

Cleaning the ventilation grille

Remove dust from the ventilation grille in the rear of the main unit periodically with a vacuum cleaner as the accumulated dust can increase the internal temperature of the main unit causing machine failure or fire hazard.

BEFORE OBTAINING SERVICE

In the event of problems with the display, check the following explanations before contacting your dealer for servicing.

Problem Action

• Power does not turn ON. • Check whether the power plug is securely inserted into the receptacle.

• No pictures are displayed. • Check cables for disconnection.

• Remote control does not function properly.

• The display makes a snapping sound. • This sound is produced when the cabinet expands or contracts due to variations in temper-

• The display makes a buzzing sound. • The display has fans to maintain the temperature of internal components at a constant

• There are spots on the screen. • Check whether your AV equipment is affected by interference from automobiles, trains,

• Degraded colors/tints • Check whether all picture adjustments have been properly made.

• Improper screen position/size • Check whether screen position and size have been properly adjusted.

• No audio • Check cables for disconnection.

• If “Out of range” appears, the display is receiving a signal whose picture or signal cannot be reproduced by the display.

• The screen turns to black and white.

• If “Error message Condition 1” appears, the fan is defective.

• If “Error message Condition 2” appears, the display’s internal components are extremely hot.

• If “Change refresh rate to 60Hz” appears, • The picture may get blurred with vertical frequency of other than 48.3-51.8 or 58.4-61.4

• If the power indicator lamp flashes red or green.

• Check whether the power for all input equipment is ON.

• Check for connection to wrong terminals or for wrong input mode.

• Check whether the input mode display is colored pink.Special setup may have been made. Return to original setup or initialize the User adjustment value.

• Check for incorrect battery orientation.

• Check for dead batteries.

• Check for distance from the display.

• Check whether you are pointing the remote control transmitter properly at the display’s receiver.

• Check for any obstacle between the remote control and the display.

ature. This sound does not indicate that the display has a problem.

level. This sound is produced by the fan as it rotates. (Applies to models equipped with a fan)

high-voltage transmission lines, neon signs or other potential sources of interference.

(See “Adjusting Pictures” on P. E-21–E-26.)

(See “Adjusting Screen Position and Size” on P. E-27.)

• Check whether the proper audio input has been selected. (See “Audio Input” on P. E-32.)

• Signals that are not supported by this display have been input. Check which signals are supported. (See the user’s manual (1/2).)

• Remove the power plug from the receptacle, and contact your dealer for repairs. (Applies to models equipped with a fan)

• Remove the power plug from the receptacle. (You can turn the power back ON again when the components have cooled sufficiently.) If the message appears again when you turn the power back on, remove the power plug from the receptacle, and contact your dealer for a repairs.

(Hz). Change the setting of your PC, etc.

• Remove the power plug from the receptacle, and inform your dealer about how the lamp flashed. The power indicator lamp flashes differently depending on the type of problem.

Note

• Functions may not be available with some models and some device options.

E-36

Fujitsu P55XHA40W, P42HHA40U, P42VHA40R, P42VHA40W, P50XHA40U User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual