Fujitsu LifeBook E4010, LifeBook E4010D User Manual

Copyright
Copyright
Fujitsu PC Corporation has made every effort to ensure the accuracy and completeness of this document. However, as ongoing development efforts are continually improving the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.
Fujitsu, the Fujitsu logo, and LifeBook are registered trademarks of Fujitsu Limited.
The following are registered trademarks of Microsoft Corporation: MS, MS-DOS, Windows.
PCMCIA is a trademark of the Personal Computer Memory Card International Association.
Intel and Pentium are registered trademarks and SpeedStep is a trademark of Intel Corporation or its subsidiaries in the United States and other countries.
Adobe Acrobat Reader is a registered trademark of Adobe System Inc.
Earthlink is a registered trademark of EarthLink Network, Inc.
Quicken is a registered trademark of Intuit, Inc. WinDVD is a trademark of InterVideo, Inc. Netscape 6 is a registered trademark of Netscape
Communications Corporation. PowerQuest and Drive Image are registered trademarks
of PowerQuest Corp.
McAfee is a registered trademark of Network Associates/ McAfee.com, Inc.
BayManager is a registered trademark of Softex, Inc.
The DVD player found in some models of the LifeBook notebook incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights users. Use of this copyright protection technology must be autho­rized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless autho­rized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Dolby Headphone manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks or registered trade­marks of Dolby Laboratories. Confidential Unpublished works. Copyrights 1992-1999 Dolby Laboratories. All rights reserved.
All other trademarks mentioned herein are the property of their respective owners.
© Copyright 2003 Fujitsu PC Corporation. All rights reserved. No part of this publication may be copied, reproduced, or translated, without prior written consent of Fujitsu PC Corporation. No part of this publication may be stored or transmitted in any electronic form without the written consent of Fujitsu PC Corporation.
B5FH-8481-01EN-00
DECLARATION OF CONFORMITY
according to FCC Part 15
Responsible Party Name: Fujitsu PC Corporation Address: 5200 Patrick Henry Drive
Telephone: (408) 982-9500 Declares that product: Model Configurations: LifeBook E4010
This device complies with Part 15 of the FCC rules. Operations are subject to the following two conditions: (1) This
device must not be allowed to cause harmful interference, (2) This device must accept any interference received, including interference that may cause undesired operation.
Santa Clara, CA 95054
LifeBook E4010D
Complies with Part 15 of the FCC Rules.
LifeBook E Series Notebook
Fujitsu LifeBook® E Series

Table of Contents

Table of Contents
1
PREFACE
Preface
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . .3
Fujitsu Contact Information . . . . . . . . . . . . . . . . .3
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
2
GETTING TO KNOW YOUR LIFEBOOK NOTEBOOK
Overview
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Locating the Controls and Connectors
Top and Front Components . . . . . . . . . . . . . . . . .8
Left-Side Panel Components . . . . . . . . . . . . . . . .9
Right-Side Panel Components . . . . . . . . . . . . . .10
Back Panel Components. . . . . . . . . . . . . . . . . . .11
Bottom Components . . . . . . . . . . . . . . . . . . . . .12
Keyboard
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . .16
Numeric Keypad. . . . . . . . . . . . . . . . . . . . . . . . .16
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . .16
Cursor Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Function Keys. . . . . . . . . . . . . . . . . . . . . . . . . . .17
TouchPad Pointing Device
Clicking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Double-Clicking . . . . . . . . . . . . . . . . . . . . . . . . .18
Dragging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TouchPad Control Adjustment . . . . . . . . . . . . . .19
Flexible Bay Devices
Removing and Installing Modular Devices . . . . .20
LifeBook Security/Application Panel
Setting up Your LifeBook Security Panel. . . . . . .22
Passwords . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Operating Your LifeBook
Security Application Panel. . . . . . . . . . . . . . .23
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Uninstalling the Security Panel Application . . . . .23
Launching Applications with
the Security/Application Panel . . . . . . . . . . .24
Status Indicator Panel
Power Indicator . . . . . . . . . . . . . . . . . . . . . . . . .13
AC Adapter Indicator . . . . . . . . . . . . . . . . . . . . .13
Battery Level Indicators . . . . . . . . . . . . . . . . . . .13
Battery Charging Indicators . . . . . . . . . . . . . . . .14
Media Drive Access Indicator . . . . . . . . . . . . . . .14
Hard Drive or Removable
Media Drive Access Indicator . . . . . . . . . . . .14
Floppy Disk Drive Access Indicator . . . . . . . . . . .14
PC Card Access Indicators . . . . . . . . . . . . . . . . .14
NumLk Indicator. . . . . . . . . . . . . . . . . . . . . . . . .14
CapsLock Indicator. . . . . . . . . . . . . . . . . . . . . . .15
ScrLk Indicator . . . . . . . . . . . . . . . . . . . . . . . . . .15
Security Indicator . . . . . . . . . . . . . . . . . . . . . . . .15
3
GETTING STARTED
Power Sources
Connecting the Power Adapters. . . . . . . . . . . . .29
Display Panel
Opening the Display Panel . . . . . . . . . . . . . . . . .30
Adjusting Display Panel Brightness . . . . . . . . . . .30
Closing the Display Panel . . . . . . . . . . . . . . . . . .30
LifeBook E Series Notebook
Starting Your LifeBook Notebook
Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Boot Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . 31
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . .31
Booting the System . . . . . . . . . . . . . . . . . . . . . .32
Registering Your LifeBook notebook . . . . . . . . .33
Installing Click Me!. . . . . . . . . . . . . . . . . . . . . . . 33
Power Management
Power and Suspend/Resume Button . . . . . . . . . 34
Suspend Mode. . . . . . . . . . . . . . . . . . . . . . . . . .34
Hibernation (Save-to-disk) Feature. . . . . . . . . . . 35
Display Timeout. . . . . . . . . . . . . . . . . . . . . . . . .35
Hard Disk Timeout. . . . . . . . . . . . . . . . . . . . . . .35
Restarting the System. . . . . . . . . . . . . . . . . . . . .35
Power Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
4
USER-INSTALLABLE FEATURES
Lithium ion Battery
Recharging the Batteries. . . . . . . . . . . . . . . . . . . 39
Replacing the Battery. . . . . . . . . . . . . . . . . . . . .40
Memory Upgrade Module
Installing a Memory Upgrade Module . . . . . . . . 49
Removing a Memory Upgrade Module . . . . . . . 49
Checking the Computer Recognition
of New Memory Capacity . . . . . . . . . . . . . . 50
Device Ports
Communications Ports. . . . . . . . . . . . . . . . . . . . 51
LAN Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Wireless LAN Port . . . . . . . . . . . . . . . . . . . . . . . 51
IEEE 1394 Jack. . . . . . . . . . . . . . . . . . . . . . . . . . 51
Parallel Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Serial Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Universal Serial Bus (USB) 2.0 Ports . . . . . . . . . . 51
Infrared Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Microphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 52
S-Video Out Port. . . . . . . . . . . . . . . . . . . . . . . . 52
Headphone Jack . . . . . . . . . . . . . . . . . . . . . . . . 52
Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
External Monitor Port . . . . . . . . . . . . . . . . . . . . 52
5
TROUBLESHOOTING
External USB Floppy Disk Drive
Loading a Disk . . . . . . . . . . . . . . . . . . . . . . . . . .41
Ejecting a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Preparing a Disk for Use. . . . . . . . . . . . . . . . . . . 41
Media Drive
Media Player Software . . . . . . . . . . . . . . . . . . . . 42
Loading Media. . . . . . . . . . . . . . . . . . . . . . . . . .42
Removing Media . . . . . . . . . . . . . . . . . . . . . . . .43
Emergency DVD/CD-ROM Tray Release . . . . . .43
Using the Media Player Software . . . . . . . . . . . .43
Using DolbyTM Headphone. . . . . . . . . . . . . . . .44
Using the Media Player on Battery Power . . . . . 44
Auto Insert Notification Function . . . . . . . . . . . .45
Hard Disk Drive
Formatting the Hard Disk Drive . . . . . . . . . . . . . 46
PC Cards
Installing PC Cards. . . . . . . . . . . . . . . . . . . . . . .47
Removing PC Cards . . . . . . . . . . . . . . . . . . . . . .47
SmartCard Reader . . . . . . . . . . . . . . . . . . . . . . .48
Troubleshooting
Identifying the Problem . . . . . . . . . . . . . . . . . . . 55
Specific Problems. . . . . . . . . . . . . . . . . . . . . . . . 56
Troubleshooting Table. . . . . . . . . . . . . . . . . . . . 56
Power On Self Test Messages . . . . . . . . . . . . . . 64
Modem Result Codes. . . . . . . . . . . . . . . . . . . . . 65
Restoring Your Pre-installed Software . . . . . . . . 66
Drive Image Special Edition (DISE) . . . . . . . . . . . 66
6
CARE AND MAINTENANCE
Care and Maintenance
LifeBook Notebook . . . . . . . . . . . . . . . . . . . . . . 71
Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Floppy Disks and Drives. . . . . . . . . . . . . . . . . . . 72
DVDs and CDs. . . . . . . . . . . . . . . . . . . . . . . . . . 72
PC Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table of Contents
7
SPECIFICATIONS
Specifications
Configuration Label . . . . . . . . . . . . . . . . . . . . . .77
Microprocessor. . . . . . . . . . . . . . . . . . . . . . . . . .77
Chipset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Mass Storage Device Options. . . . . . . . . . . . . . .77
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Device Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Environmental Requirements . . . . . . . . . . . . . . .78
Popular Accessories . . . . . . . . . . . . . . . . . . . . . .79
Pre-Installed Software . . . . . . . . . . . . . . . . . . . .80
Application Descriptions. . . . . . . . . . . . . . . . . . .81
8
Connection using Windows 2000
Flow of operations . . . . . . . . . . . . . . . . . . . . . .107
Preparation for wireless LAN connection . . . . .107
Connection to the network. . . . . . . . . . . . . . . .109
Other settings
Setting of power-saving function . . . . . . . . . . .113
Troubleshooting the Wireless LAN
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . .114
Wireless LAN Glossary
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
IP address information
IP Information . . . . . . . . . . . . . . . . . . . . . . . . .119
Wireless LAN Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .120
INDEX
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
GLOSSARY
Glossary
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85
APPENDIX: INTEGRATED WIRELESS LAN USER’S GUIDE
FCC Regulatory Information. . . . . . . . . . . . . . . .97
Before Using the Wireless LAN
For better communications. . . . . . . . . . . . . . . . .99
Stopping transmission. . . . . . . . . . . . . . . . . . . .100
Starting Transmission . . . . . . . . . . . . . . . . . . . .100
Connection using Windows XP
Flow of operations . . . . . . . . . . . . . . . . . . . . . .101
Preparation for wireless LAN connection . . . . .101
Connection to the network. . . . . . . . . . . . . . . .103
LifeBook E Series Notebook
1
Preface
1
LifeBook E Series Notebook - Section 1
2

Preface

Preface
ABOUT THIS GUIDE
The LifeBook® E Series notebook from Fujitsu PC Corporation is a powerful notebook computer. It is powered by an Intel microprocessor, has a built-in color display, a number of possible configurations, and brings the computing power of desktop personal computers (PCs) to a portable environment.
This manual explains how to operate your LifeBook notebook’s hardware and built-in system software. Your notebook is compatible with the IBM® PC AT.
It comes with Microsoft® Windows® 2000 Professional, Windows XP Home Edition, or Windows XP Profes­sional pre-installed.
The LifeBook notebook is a completely self-contained unit with either an active-matrix XGA or SXGA+ TFT color LCD display. It has a powerful interface that enables it to support a variety of optional features.
Conventions Used in the Guide
Keyboard keys appear in brackets. Example: [Fn], [F1], [ESC], [ENTER] and [CTRL].
Pages with additional information about a specific topic are cross-referenced within the text. Example: (See page xx.)
On screen buttons or menu items appear in bold Example: Click OK to restart your LifeBook notebook.
DOS commands you enter appear in Courier type. Example: Shut down the computer?
POINT
The point icon highlights information that will enhance your understanding of the subject material.
CAUTION
The caution icon highlights information that is important to the safe operation of your computer, or to the integrity of your files. Please read all caution information carefully.
FUJITSU CONTACT INFORMATION
Service and Support
You can contact Fujitsu Service and Support the following ways:
Toll free: 1-800-8Fujitsu (1-800-838-5487)
Fax: 1-901-259-5700
E-mail: 8fujitsu@fujitsupc.com
Web site: http://www.fujitsupc.com
Before you place the call, you should have the following information ready so that the customer support representative can provide you with the fastest possible solution:
Product name
Product configuration number
Product serial number
Purchase date
Conditions under which the problem occurred
Any error messages that have occurred
Hardware configuration
Type of device connected, if any
Fujitsu Online
You can go directly to the online Fujitsu Product catalog for your LifeBook notebook by clicking on the LifeBook Accessories Web site URL link, located in the Windows Start menu.
You can also reach Fujitsu Service and Support online by clicking on the Fujitsu Service and Support Web site URL link, located in the Service and Support Software folder of the Windows Start menu.
POINT
You must have an active internet connection to use the on-line URL links.
WARRANTY
Depending upon the configuration of your LifeBook notebook, your system is backed by either a one-year or three-year International Limited Warranty. Check the information that came with your LifeBook notebook for further warranty terms and conditions.
WARNING
The warning icon highlights information that can be hazardous to either you, your LifeBook notebook, or your files. Please read all warning information carefully.
3
LifeBook E Series Notebook – Section 1
4
2
Getting to Know Your LifeBook Notebook
5
LifeBook E Series Notebook – Section 2
6
Figure 2-1. LifeBook E Series

Overview

This section describes the components of your Fujitsu LifeBook notebook. We strongly recommend that you read it before using your LifeBook notebook – even if you are already familiar with notebook computers.
UNPACKING
When you receive your LifeBook notebook, unpack it carefully, and compare the parts you have received with the items listed below.

Getting to Know Your LifeBook

Figure 2-2. AC Adapter
For a pre-configured model you should have:
LifeBook E Series notebook computer (Figure 2-1)
Lithium ion battery, pre-installed
AC adapter with AC power cord (Figure 2-2)
Weight Saver
Modular optical drive
Phone/Modem (RJ-11) telephone cable
Drivers and Applications Restore CD
Getting Started Guide
User’s Guide (this guide)
International Limited Warranty Brochure
Microsoft-associated materials
Premium Care registration card
Depending upon the configuration of your system, one or more of the following items may also be included in the box:
External USB floppy disk drive
DVD Application CD
CD-RW Application CD
Additional battery(ies)
7
LifeBook E Series Notebook – Section 2
Status
Indicator
Panel
Closed
Cover
Switch
Tou ch pa d
Pointing
Device
Stereo
Speaker
Headphone
Jack
Microphone Jack
Figure 2-3. LifeBook notebook with display open
Locating the Controls
Stereo Speaker
Display Panel Latch
Display Panel
LifeBook Security/ Application Panel
Power and Suspend/ Resume
Button
Keyboard
Stereo Speakers
The built-in dual speakers allow for stereo sound.
and Connectors
TOP AND FRONT COMPONENTS
The following is a brief description of your LifeBook notebook’s top and front components.
Display Panel Latch
The display latch locks and releases the display panel.
Display Panel
The display panel is a color LCD panel with back lighting for the display of text and graphics.
Status Indicator Panel
The Status Indicator Panel displays symbols that corre­spond to specific components of your notebook. (See
Status Indicator Panel on page 13 for more information)
Power and Suspend/Resume Button
The Power and Suspend/Resume button is always used to power on your notebook from its Off state. It is also used as the Suspend/Resume button. This allows you to suspend notebook activity without powering off, resume your notebook from suspend mode, and power on your notebook when it has been shut down. (See Power On on
page 31 for more information) and (See Power and Suspend/Resume Button on page 34 for more information)
Closed Cover Switch
The closed cover switch turns off the LCD backlighting when the display panel is closed.
Keyboard
A full-size keyboard with dedicated Windows keys.
(See Using the Keyboard on page 16 for more information)
Touchpad Pointing Device
The pointing device is a Touchpad that allows you simple cursor control. (See TouchPad Pointing Device on
page 18 for more information)
LifeBook Security/Application Panel
The LifeBook Security/Application Panel provides hardware security and one-touch application launch capability. (See LifeBook Security/ Application Panel on
page 22 for more information)
Microphone Jack
The microphone jack allows you to connect an external mono microphone. (See Microphone Jack on page 52 for
more information)
Headphone Jack
The headphone jack allows you to connect headphones or powered external speakers. (See Headphone Jack on
page 52 for more information)
8
Getting to Know Your LifeBook
Wireless LAN Antenna On/Off Switch
Fan Vents
Figure 2-4. LifeBook notebook left-side panel
Modem Port
LEFT-SIDE PANEL COMPONENTS
Following is a brief description of your LifeBook note­book’s left-side components.
Modem Port
The modem port is designed to accept a Modem (RJ-11) telephone jack for the multi-national internal 56K modem. (See Communications Ports on page 51 for more
information)
POINT
The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by FCC, and its actual connection rate depends on the line conditions. The maximum upload speed is 33600bps.
Anti-theft Lock Slot
PC Card Slots
PC Card Eject Buttons
PC Card Slots
The PC Card Slots allow you to install two Type I or Type II PC Cards or one Type III PC Card.
(See PC Cards on page 47 for more information)
Anti-theft Lock Slot
The anti-theft lock slot allows you to attach an optional physical lock down device.
Fan Vents
The fan vents assist in the proper cooling of the system.
Wireless LAN Antenna On/Off Switch
The Wireless LAN Antenna On/Off Switch turns the wireless LAN antenna on and off in systems with an optional Wireless LAN device installed. For systems without an optional Wireless LAN device installed, the Wireless Antenna On/Off Switch is present, but non­functional.
CAUTION
The internal modem is not intended for use with Digital PBX systems. Do not connect the internal modem to a digital PBX as it may cause serious damage to the internal modem or your entire LifeBook notebook. Consult your PBX manufacturer’s documentation for details. Some hotels have Digital PBX systems. Be sure to find out BEFORE you connect your modem. Third­party hardware is available to allow modem-to-PBX interface.
9
LifeBook E Series Notebook – Section 2
Figure 2-5. LifeBook notebook right-side panel
Flexible Bay Release Latch
Flexible Bay
RIGHT-SIDE PANEL COMPONENTS
Following is a brief description of your LifeBook note­book’s right-side components.
Flexible Bay
The Flexible Bay can accommodate one of the following devices. (See Flexible Bay Devices on page 20 for more
information)
Modular DVD/CD-RW combo drive
Modular DVD drive
Modular CD-ROM drive
Modular Lithium ion bay battery
Flexible Bay Release Latch
The Flexible Bay release latch releases the Flexible Bay device.
10
Serial Port
Parallel Port
External Monitor Port
Getting to Know Your LifeBook
Infrared Port
LAN Port
S-Video Out Port
Figure 2-6. LifeBook notebook back panel
BACK PANEL COMPONENTS
Following is a brief description of your LifeBook note­book’s rear panel components.
Serial Port
The serial port allows you to connect serial (RS-232C) devices. (This is also sometimes referred to as a COMM port.) (See Serial Port on page 51 for more information)
Parallel Port
The parallel port allows you to connect parallel devices. (This is also sometimes referred to as an LPT port.) (See Parallel Port on page 51 for more infor-
mation)
External Monitor Port
The external monitor port allows you to connect an external monitor. (See External Monitor Port on page 52
for more information)
Infrared Port
The fast IrDA compatible port allows you to communi­cate with another IrDA compatible infrared device without a cable.
DC Power Jack
USB 2.0 Ports (Qty. 2)
USB 2.0 Ports
The USB ports allow you to connect Universal Serial Bus
2.0 or USB 1.1 devices. (See Universal Serial Bus (USB)
2.0 Ports on page 51 for more information)
DC Power Jack
The DC power jack allows you to plug in the AC adapter or the optional Auto/Airline adapter to power your Life­Book notebook and charge the internal Lithium ion battery.
LAN Port
The LAN port is designed to accept a Local Area Network (LAN) RJ-45 jack. (See Communications Ports
on page 51 for more information)
S-Video Out Port
The S-Video out port is used to transmit a higher resolution video signal to a compatible TV or VCR.
(See S-Video Out Port on page 52 for more information)
11
LifeBook E Series Notebook – Section 2
Part Number
Label
(approximate
location)
Main Unit
Label
(approximate
location)
Lithium ion Battery Bay
Figure 2-7. LifeBook notebook bottom panel
Docking Port
Certificate of Authenticity
(approximate location)
Memory Upgrade Compartment

BOTTOM COMPONENTS

Following is a brief description of your LifeBook note­book’s bottom panel components.
Configuration Label and Version Label
The configuration label shows the configuration part number, the Fujitsu part number, and the various components that make up your LifeBook notebook. The version label contains the system part number and serial number. These labels provide manufacturer information that you will need to give your support representative in the event you find it necessary to contact Fujitsu.
Lithium ion Battery Bay
The battery bay contains the internal Lithium ion battery. It can be opened for the removal of the battery
when stored over a long period of time or for swapping a discharged battery with a charged Lithium ion battery.
(See Lithium ion Battery on page 39 for more information)
Docking Port
The docking port allows you to connect an optional port replicator or docking station. (See Docking Port on
page 52 for more information)
Memory Upgrade Compartment
Your LifeBook notebook comes with high speed PC2100 DDR266 SO-DIMM memory. The memory upgrade compartment allows you to expand the system memory capacity of your LifeBook notebook, hence improving overall performance. (See Memory Upgrade Module on
page 49 for more information)
12
Getting to Know Your LifeBook
Power
Battery Identifier
AC Adapter Battery
Level
Battery Charging
Hard Drive Access
Media Drive Access
Figure 2-8 Status Indicator Panel

Status Indicator Panel

The Status Indicator panel is located in the recess just above your keyboard. Within this panel are symbols that correspond with a specific component of your LifeBook notebook. These symbols tell you how each of those components are operating. (Figure 2-8)
POWER INDICATOR
The Power indicator symbol states whether your system is operational. It has several different states, each of which tells you what mode your LifeBook notebook is in at that time.
Steady On: This means that there is power to your LifeBook notebook and that it is ready for use.
Flashing: This means that your LifeBook notebook is in Suspend mode.
Steady Off: This means that your system is either in Save-to-Disk mode, or that your LifeBook notebook has been turned off with the power/suspend/resume button.
If you are charging your battery, the Power indicator symbol remains on even if your notebook is shut off. The Power indicator symbol will also remain on if you have either adapter connected and are shut down from Windows, but have not turned off with the power/ suspend/resume button.
PC Card Slot Identifier
Floppy Disk Drive Access
PC Card Access
NumLk
CapsLk
ScrLk
Security Indicator
Airline adapter or the batteries. This icon has two different states that can tell you what power source your LifeBook notebook is using.
On: This means that either of the adapters are currently in use.
Off: Power is only coming from the batteries, and you do not have an adapter connected.
BATTERY LEVEL INDICATORS
The two Battery Level indicators state whether or not the primary Lithium ion battery and/or the optional second Lithium ion battery are installed (Battery 1 refers to the primary Lithium ion battery, while Battery 2 refers to the Flexible Bay optional second battery). In addition, this symbol states how much charge is available within each installed battery. The symbol will only be displayed for a battery that is currently installed in your LifeBook note­book. (Figure 2-9)
AC ADAPTER INDICATOR
The AC Adapter indicator states whether your LifeBook notebook is operating from the AC adapter, the Auto/
13
LifeBook E Series Notebook – Section 2
76%–100% Charging
76%–100%
51%–75%
26%–50%
11%–25%
Low Warning <11%
Critical Low or Dead Battery
Shorted Battery
Figure 2-9 Battery Level Indicator
CAUTION
A shorted battery is damaged and must be replaced immediately.
POINT
If there is no battery activity, the power adapters are not connected, and the power is Off, the Battery Level indicators will also be off.
BATTERY CHARGING INDICATORS
Located to the left of each of the Battery Level indicators is a small arrow symbol. This symbol states whether that specific battery is charging. This indicator operates whether the power on or off, and will flash if the battery is too hot or cold to charge.
POINT
The Windows DVD/CD Auto Insert Notification function will periodically check for a DVD/CD installed in the drive, causing the Media Drive Access indicator to flash. The DVD/CD Auto Insert Notification function allows your system to automatically start a DVD/CD as soon as it is inserted in the drive and the tray is closed. It will begin playing an audio DVD/CD or will start an application if the DVD/CD has an auto-run file.
(See Auto Insert Notification Function on page 45 for more information)
HARD DRIVE OR REMOVABLE
MEDIA DRIVE ACCESS INDICATOR
The Hard Drive Access indicator states whether your internal hard drive or optional second hard drive is being accessed.
POINT
The Hard Drive Access indicator does not show which hard drive is being accessed.
FLOPPY DISK DRIVE
ACCESS INDICATOR
The Floppy Disk Drive Access indicator states whether the floppy disk drive is being accessed. This indicator will flash if your software tries to access a disk even if no floppy disk drive is installed. (See External USB Floppy
Disk Drive on page 41 for more information)
CAUTION
Batteries subjected to shocks, vibration or extreme temperatures can be permanently damaged.
MEDIA DRIVE ACCESS INDICATOR
The Media Drive Access indicator tells you that the DVD or CD-RW drive is being accessed. If the Auto Insert function is active, the indicator will flash periodically when your system is checking the media drive. If the Auto Insert Notification function is not active, the indi­cator will only flash when you access the media drive. The default setting is the Auto Insert Notification func­tion active. (See Auto Insert Notification Function on
page 45 for more information)
14
PC CARD ACCESS INDICATORS
The PC Card Access indicator(s) state whether or not your LifeBook notebook is accessing a PC Card(s). The indicator will flash if your software tries to access a PC Card even if there is no card installed. The number inside the indicator refers to which PC Card slot is being accessed. (See PC Cards on page 47 for more information)
NUMLK INDICATOR
The NumLk indicator states that the internal keyboard is set in ten-key numeric keypad mode. (See Using the
Keyboard on page 16 for more information)
POINT
If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external keypad. The indicator will come on, however it will not change any of the functionality of your keyboard keys.
CAPSLOCK INDICATOR
The CapsLock indicator states that your keyboard is set to type in all capital letters. (See Using the Keyboard on
page 16 for more information)
SCRLK INDICATOR
The ScrLk indicator states that your scroll lock is active.
(See Using the Keyboard on page 16 for more information)
SECURITY INDICATOR
The Security Indicator flashes (if a password was set) when the system resumes from Off or Suspend modes. You must enter the password that was set in the Security Panel before your system will resume operation.
Getting to Know Your LifeBook
15
LifeBook E Series Notebook – Section 2
Function Keys
Fn Key
Start Key
Numeric Keypad (surrounded with
thick black line)
Figure 2-10 Keyboard

Keyboard

USING THE KEYBOARD
Your Fujitsu LifeBook notebook has an integral 87-key keyboard. The keys perform all the standard functions of a 101-key keyboard, including the Windows keys and other special function keys. This section describes the following keys.
Numeric keypad: Your LifeBook notebook allows certain keys to serve dual purposes, both as standard characters and as numeric and mathematical keys. The ability to toggle between the standard character and numerical keys is controlled through the [NumLk] key.
Cursor keys: Your keyboard contains four arrow keys for moving the cursor or insertion point to the right, left, up, or down within windows, applications and documents.
Function keys: The keys labeled [F1] through [F12] are used in conjunction with the [Fn] key to produce special actions that vary depending on what program is running.
Windows keys: These keys work with your Windows operating system and function the same as the onscreen Start menu button, or the right button on your pointing device.
NUMERIC KEYPAD
Certain keys on the keyboard perform dual functions as both standard character keys and numeric keypad keys. NumLk can be activated by pressing the [NumLk] keys. Turning off the NumLk feature is done the same way.
Start Key
Application Key
Cursor Keys
Once this feature is activated you can enter numerals 0 through 9, perform addition ( + ), subtraction ( - ), multiplication ( * ), or division ( / ), and enter decimal points ( . ) using the keys designated as ten-key function keys. The keys in the numeric keypad are marked on the front edge of the key to indicate their secondary func­tions.
POINT
If you are using the optional external numerical keypad, pressing the [NumLk] key will activate the external key­pad. The indicator will come on, however it will not change any of the functionality of your keyboard keys.
WINDOWS KEYS
Your LifeBook notebook has three Windows keys: two Start keys and an Application key. The two Start keys display the Start menu. This button functions the same as your onscreen Start menu button. The Application key functions the same as your right mouse button and displays shortcut menus for the selected item. (Please refer to your Windows documentation for additional information regarding the Windows keys.)
CURSOR KEYS
The cursor keys are the four arrow keys on the keyboard which allow you to move the cursor up, down, left and right in applications. In programs such as Windows Explorer, it moves the “focus” (selects the next item up, down, left, or right).
16
FUNCTION KEYS
Your LifeBook notebook has 12 function keys, F1 through F12. The functions assigned to these keys differ for each application. You should refer to your software documentation to find out how these keys are used.
The [Fn] key provides extended functions for the notebook and is always used in conjunction with another key.
[Fn+F3]: Pressing [F3] while holding [Fn] will toggle the Audio Mute on and off.
[Fn+F4]: Pressing [F4] while holding [Fn] will toggle the touchpad on and off. (This function key combina­tion only works if the BIOS setting for Advanced> Keyboard/Mouse Features>Internal Pointing Device is set to Manual Setting.)
[Fn+F5]: Pressing [F5] while holding [Fn] allows you to toggle between video compensation and no compensation. (Video compensation controls spacing on the display. When it is enabled, displays with less than 1024 x 768 or 800 x 600 pixel resolution will still cover the entire screen.)
[Fn+F6]: Pressing [F6] repeatedly while holding [Fn] will lower the brightness of your display.
[Fn+F7]: Pressing [F7] repeatedly while holding [Fn] will increase the brightness of the display.
[Fn+F8]: Pressing [F8] repeatedly while holding [Fn] will decrease the volume of your LifeBook notebook.
[Fn+F9]: Pressing [F9] repeatedly while holding [Fn] will increase the volume of your LifeBook notebook.
[Fn+F10]: Pressing [F10] while holding [Fn] allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order, are: built-in display panel only, both built-in display panel and external monitor or external monitor only.
Getting to Know Your LifeBook
17
LifeBook E Series Notebook – Section 2
Cursor
Cursor Control
Left Button
Right Button
Figure 2-11. TouchPad pointing device

TouchPad Pointing Device

The TouchPad pointing device is built into your Fujitsu LifeBook notebook. It is used to control the movement of the pointer to select items on your display panel. The TouchPad is composed of a cursor control and a left and right button. The cursor control works the same way a mouse does, and moves the cursor around the display. It only requires light pressure with the tip of your finger, and the more pressure you use, the faster the cursor will move. The left and right buttons function the same as mouse buttons. The actual functionality of the buttons may vary depending on the application that is being used. (Figure 2-11)
POINT
An external mouse can be connected to the USB port on your LifeBook notebook, and be used simulta­neously with the TouchPad. However, if you boot the system with an external mouse connected the Touch­Pad will be disabled or enabled depending on your BIOS settings.
more information)
(See BIOS Setup Utility on page 31 for
CLICKING
Clicking means pushing and releasing a button. To left-click, move the cursor to the item you wish to select, press the left button once, and then immedi­ately release it. To right-click, move the mouse cursor to the item you wish to select, press the right button once, and then immediately release it. You also have the option to perform the clicking operation by tapping lightly on the TouchPad once. (Figure 2-12)
Figure 2-12. Clicking
DOUBLE-CLICKING
Double-clicking means pushing and releasing the left button twice in rapid succession. This procedure does not function with the right button. To double-click, move the cursor to the item you wish to select, press the left button twice, and then immediately release it. You also have the option to perform the double-click operation by tapping lightly on the TouchPad twice.
(Figure 2-13)
18
Figure 2-13. Double-clicking
POINT
If the interval between clicks is too long, the double-click will not be executed.
DRAGGING
Dragging means pressing and holding the left button, while moving the cursor. To drag, move the cursor to the item you wish to move. Press and hold the left button while moving the item to its new location and then release it. Dragging can also be done using the TouchPad. First, tap the TouchPad twice over the item you wish to move making sure to leave your finger on the pad after the final tap. Next, move the object to its new location by moving your finger across the TouchPad, and then release your finger. (Figure 2-14)
Getting to Know Your LifeBook
Figure 2-14. Dragging
TOUCHPAD CONTROL ADJUSTMENT
The Windows Control Panel allows you to customize your TouchPad with selections made from within the Mouse Properties dialog box.
19
LifeBook E Series Notebook – Section 2
Figure 2-15 Flexible Bay

Flexible Bay Devices

Your LifeBook notebook contains a Flexible Bay. The Flexible Bay can accommodate a modular CD-ROM drive, DVD drive, DVD/CD-RW drive, Lithium ion battery, or weight saver. (Figure 2-15)
You Flexible Bay will have one of the following devices installed. All devices listed here are also options which can be purchased separately. (Figure 2-16)
Modular CD-ROM drive: This allows you to access software and audio CDs.
Modular DVD drive: This allows you to access movies, software, and audio DVD/CDs.
Modular DVD-CD-RW combo drive: This allows you to access movies, software, and audio DVD/CDs as well as to write to CDs.
Modular Lithium ion battery: This is a rechargeable battery that can be used to power your LifeBook note­book when an adapter is not connected.
Weight Saver: This is used to fill the bay when no device is needed.
Flexible Bay
CD-ROM Drive
DVD/CD-RW Combo Drive
DVD Drive
Lithium ion Bay Battery
Weight Saver
Figure 2-16 Flexible Bay Devices
POINT
You should never leave your Flexible Bay empty when the LifeBook notebook is in operation.
REMOVING AND INSTALLING MODULAR DEVICES
There are two ways to remove and install modular devices in the Flexible Bay:
Cold-swapping: Swapping devices while your LifeBook notebook is powered off. (Reference the following section.)
Hot-swapping: Swapping devices while your system is active using BayManager sections of this chapter entitled "Hot-swapping".)
20
software. (Reference the
Cold-swapping
To cold-swap modular devices in your Flexible Bay follow these easy steps: (Figure 2-17)
1. Close any open files.
2. Shut down your LifeBook notebook.
3. Pull out the Flexible Bay release latch, then press the latch in to release the modular device. This will push your device out slightly, allowing you to remove the device.
4. Slide your device out until it is clear of the bay. This will require light force.
Flexible Bay Release Latch
Figure 2-17 Removing a device from the Flexible Bay
Getting to Know Your LifeBook
Figure 2-18 Installing a device in the Flexible Bay
CAUTION
Be careful when aligning and seating devices in the bay. If the fit is incorrect, you may damage the bay or the device. If the device does not move easily in the bay, remove it, and check for dirt or foreign objects. It will require a firm push to latch the device in place.
5. Slide the device you are installing into your LifeBook notebook until it clicks into place.
6. It is now safe to turn your notebook back on.
7. You can now access and use the device.
Your LifeBook notebook will automatically detect the new device and activate it within your system. The drive letters associated with the device will be created and listed under My Computer and Windows Explorer.
Hot-swapping
Under Windows 2000 and XP, hot-swapping is provided through the Unplug or Eject Hardware utility. The icon for the utility appears on the taskbar. Refer to your Windows manual on using this feature.
21
LifeBook E Series Notebook – Section 2
Figure 2-19 LifeBook Security/Application Panel
123 4
Numbered Buttons for entering password and launching applications
Enter Button

LifeBook Security/ Application Panel

A unique feature of your LifeBook notebook is the Security/Application Panel that allows you to secure your notebook from unauthorized use. The Security/ Application Panel also allows you to launch applications with the touch of a button when your system is on.
If the security system is activated, upon starting your LifeBook notebook or resuming from suspend mode the security system requires you to enter a password code using the buttons on the Security/Application Panel. After entering a correct password, your LifeBook notebook resumes system operation. (Figure 2-19)
SETTING UP YOUR LIFEBOOK SECURITY PANEL
When you receive your LifeBook notebook, the security panel application is pre-installed without any passwords.
The following sections provide detailed information on your security panel, and how to set, change or remove passwords.
Numbered Buttons
Use these buttons to enter your password. (Figure 2-19)
Enter Button
After entering the button strokes, push this button to enter the password into the notebook. (Figure 2-19)
notebooks in a group environment should not use a common password. A password consists of one to five button strokes plus the enter button. A valid stroke consists of pushing one or up to four buttons simulta­neously. The following are valid button strokes:
n
Pushing [4] by itself
n
Pushing [2] and [3] at the same time
n
Pushing [1], [2], and [4] at the same time
n
Pushing [1], [2], [3], and [4] at the same time
The following are valid passwords. The numbers within braces ({ }) are button strokes using more than one button.
n
{[2]+[3]}, [1], [enter]
n
[4], [enter]
n
{[1]+[3]}, {[2]+[3]+[4]}, [1], [4], [2], [enter]
Setting Passwords
When shipped from the factory, no passwords are set. You have a choice of having no password or setting a supervisor and user password. You must set the super­visor password before the user password.
POINTS
n
The purpose of supervisor password is to be able to bypass the user password in case the user password is forgotten. The supervisor password alone will not lock the system.
n
You have to set both the supervisor and user pass­words for the security panel to work.
PASSWORDS
The user and supervisor password may be set on this LifeBook notebook. A supervisor password is typically the same for all notebooks in a working group, office, or company to allow for system management. Individual
22
Getting to Know Your LifeBook
Setting Supervisor Password
You must have set a supervisor password before setting any user passwords. The supervisor password can bypass the user password.
1. Go to the Start menu.
2. Click on Run.
3. Type in
"C:\Program Files\Fujitsu\ Security Panel Application\ Supervisor\FJSECS.EXE" (be sure to use
the quotation marks), then press [Enter]
4. Follow the on-screen instructions to set the Supervisor password.
Setting User Password
1 Go to the Start menu.
2. Click on Programs.
3. Click on Security Panel Application > Security Panel Application.
4. Follow the on-screen instructions to set the user password.
POINT
You may change or remove the supervisor or user password by repeating the steps defined above.
OPERATING YOUR LIFEBOOK SECURITY APPLICATION PANEL
The security lock feature is in effect both when the system resumes from OFF or suspend state. You always need to push the Suspend /Resume button to input the user pass­word. Your system will not begin the boot sequence without entering your supervisor/user password.
From Off State
1. Turn on your system.
2. When the Security Indicator flashes, enter the password and press Enter button.
For example, if the password is 22222, Press Button Number 2 five times and press Enter button.
The LifeBook notebook will boot to normal opera­tion.
From Suspend State
1. Press your Suspend/Resume button.
2. When the Security Indicator flashes, enter the pass­word and press Enter button.
The notebook should resume normal operation.
Incorrect Password Entry
If an invalid supervisor or user password is entered three times in succession, the system will “beep” for about one
minute. If a valid password is entered within a minute (while system beeps), the beeping will stop and the Life­Book notebook will resume normal operation. If no password or an invalid password is entered while the system beeps, the system will return to its previous locked state (suspend or off) and the Security Indicator will go off. To reactivate the LifeBook notebook after a password failure, you must press the Suspend/Resume button, then enter a correct password.
POINT
Remember the user password you specified on the Security Panel Application. If you forget the password you will not be able to use your computer. The super­visor password can override the user password.
PRECAUTIONS
Opening and Closing the Cover
Closing the cover may place the notebook into suspend mode. Opening the cover does not automatically place the notebook into normal operation. Instead, you must enter the proper security password after pushing the Suspend/Resume button.
Low Battery Operations
If your LifeBook notebook has a low battery, pushing the suspend/resume button only turns on the Security Indicator. Your notebook does not unlock, and the Security Indicator LED turns off after one minute. To resume normal operation, first attach a power supply to the LifeBook notebook. Then you may unlock the note­book.
UNINSTALLING THE SECURITY PANEL APPLICATION
You have two options when uninstalling the security panel application:
n
Uninstall the security panel application software. This will disable all security feature.
n
Uninstall the security panel application with password still active. This will not allow any changes to the password.
Uninstalling the Security Panel Application Software
Remove passwords when User wants no password protection whatsoever and doesn’t want to give anybody the utility to set a password on their computer. In this case, if passwords (supervisor, user, or both) are set, the passwords must first be cleared BEFORE removing the application. To clear passwords, follow same procedure in SETTING PASSWORD CODES except this time, select REMOVE, enter current password then click Next. When asked to confirm select Yes .
23
LifeBook E Series Notebook – Section 2
Removing Security Panel Application with Passwords Still Active
Using this feature will not allow any changes to the password.
POINT
Removing the applications does not remove the password. It simply removes the utility to change/add/ remove passwords. To change your password you must reinstall the application.
User:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the
Control Panel.
3. Select the Security Panel Application in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears, click Ye s .
Supervisor:
1. Go to Start Menu, Click on Control Panel.
2. Open Add/Remove Programs Properties in the Control Panel.
3. Select the Security Panel Application for Supervisor in the list, and click Add/Remove.
4. When the Confirm File Deletion box appears, click Ye s .
Reinstalling the Security Application Panel
To reinstall supervisor or user security application, you will need your Drivers and Applications Restore CD. The Secpanel folder located in the Utilities\Security Panel contains the setup files for supervisor and user security application.
1. Double-click the Setup FJSECS.EXE file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.
2. Double-click the Setup FJSECU.EXE file. The Installing Security Panel Application window will appear. Follow the instructions on the screen.
Supervisor and user passwords can be set by the Windows Software which are FJSECS.EXE and FJSECU.EXE respectively. FJSECU.EXE for user pass­word cannot run without supervisor password. First you need to run FJSECS.EXE to set supervisor pass­word before setting user password. Follow instructions under Setting Passwords on page 22.
If you forget both passwords, contact Fujitsu Service and Support at 1-800-8Fujitsu (1-800-838-5487). Fujitsu charges a service fee for unlocking a password restricted LifeBook notebook. When calling please have a valid credit card and provide proof of ownership. You will
then be given instructions on where to ship your Life­Book notebook.
LAUNCHING APPLICATIONS WITH THE SECURITY/APPLICATION PANEL
The security panel also enables you to launch applications with the touch of a button when your system is on. Pressing any of the buttons will launch a user-defined application. Your LifeBook notebook is pre-installed with software utilities that let you operate and configure your LifeBook Security/Application Panel. These utilities are found under the Start menu, under Programs, then under LifeBook Application Panel. They include Application Panel Setup, Guide, Activate Panel and Deactivate Panel.
Configuring your LifeBook Application Panel
When you start Windows, the LifeBook Application Panel is automatically activated. An icon resembling a finger pressing a button will appear on the system tray (the indented portion of the status bar where the clock is displayed). When you see this icon you will know that LifeBook Application Panel is active.
As an application launcher, the LifeBook Application Panel is very flexible, giving you a variety of options. To set up the Panel to best suit your needs, we have provided the Application Panel Setup utility that quickly and easily helps you make the most of this valuable feature.
To configure your LifeBook Application Panel with Application Panel Setup:
1. Click on Start.
2. Click on Programs.
3. Click on LifeBook Application Panel.
4. Click on Application Panel Setup.
The Application Panel Setup utility will appear. There are tabs that correspond to the application buttons on the LifeBook Application Panel. When you receive your LifeBook notebook, these buttons are pre-configured to launch the associated programs, as defined in Chapter 7.
POINT
The tabs in Application Panel Setup may not be in the same order as the buttons on your LifeBook notebook, please select the tab you wish to change carefully.
To change an application associated with the Application buttons, click on the tab for the button you would like to reconfigure – for example, Application A. Click on Browse from Start Menu, scroll down the list of applica­tions, click on the application you wish to launch with this button, and then click OK. The button will now launch the new application.
24
Getting to Know Your LifeBook
The Internet tab is different. It comes set to launch your Windows default Internet browser (Internet Explorer), unless you have changed this in Windows. In order to reconfigure it to launch another program follow these easy steps:
1. Click on Other from the Internet browser box.
2. Click on Browse from Start Menu.
3. Scroll down the list of applications, and then click on the application you wish to launch with this button.
4. Click OK.
The button will now launch the new application. If you want to return to launching your Windows default Internet browser with this button, you need only click on “Default Internet Browser” from the Internet browser box. Be aware that you will erase the settings for the “other application”. If you wish to go back to launching the “other application” from this button, you will need to reconfigure it as described above.
POINT
The Internet or E-mail buttons can be configured to launch any application you wish, not just an Internet browser or e-mail program.
Deactivating and Activating the LifeBook Application Panel
To deactivate the LifeBook Application Panel, follow these easy steps:
1. Click on Start.
2. Click on Programs.
3. Click on LifeBook Application Panel.
4. Click on Deactivate Panel.
To reactivate, follow the same procedure, except for step 4. Click on Activate Panel instead.
POINT
Every time you start Windows the LifeBook Application Panel is activated, even if you deactivated it before you shut down.
When you have finished with Application Panel Setup click OK, and the new settings will take effect. You can reconfigure your LifeBook Application Panel as often as you like.
25
LifeBook E Series Notebook – Section 2
26
3
Getting Started
27
LifeBook E Series Notebook – Section 3
28
AC Cable
Getting Started
DC Power Jack
DC Output Cable
AC Adapter
Figure 3-1 Connecting the AC Adapter

Power Sources

Your Fujitsu LifeBook notebook has four possible power sources: a primary Lithium ion battery, a secondary Lithium ion battery (for Flexible Bay installation), an AC adapter, or an optional Auto/Airline adapter.
CONNECTING THE POWER ADAPTERS
The AC adapter or optional Auto/Airline adapter provides power for operating your LifeBook notebook and charging the batteries.
Connecting the AC Adapter
1. Plug the DC output cable into the DC power jack of your LifeBook notebook.
2. Plug the AC adapter into an AC electrical outlet.
(Figure 3-1)
Connecting the Optional Auto/Airline Adapter
1. Plug the DC output cable into the DC power jack on your LifeBook notebook.
2. Plug the Auto/Airline adapter into the cigarette lighter of an automobile with the ignition key in the On or Accessories position.
OR
3. Plug the Auto/Airline adapter into the DC power jack on an airplane seat.
Switching from AC Adapter Power or the Auto/Airline Adapter to Battery Power
1. Be sure that you have at least one charged battery installed.
2. Remove the AC adapter or the Auto/Airline adapter.
POINT
The Lithium ion battery is not charged upon purchase. Initially, you will need to connect either the AC adapter or the Auto/Airline adapter to use your LifeBook notebook.
29
LifeBook E Series Notebook – Section 3
Display Panel Latch
Figure 3-2 Opening the Display Panel

Display Panel

Your Fujitsu LifeBook notebook contains a display panel that is backlit for easier viewing in bright environments and maintains top resolution through the use of active­matrix technology.
OPENING THE DISPLAY PANEL
1. Slide the display panel latch to the right to release the locking mechanism.
2. Lift the display panel backwards, being careful not to touch the screen, until it is at a comfortable viewing angle.
ADJUSTING DISPLAY PANEL BRIGHTNESS
Once you have turned on your LifeBook notebook, you may want to adjust the brightness level of the screen to a more comfortable viewing level. There are two ways to adjust the brightness keyboard and power management utility
Keyboard
[Fn+F6]: Pressing repeatedly will lower the brightness of your display.
[Fn+F7]: Pressing repeatedly will increase the brightness of the display.
POINT
If using AC power, your LifeBook notebook’s brightness setting is set to its highest level by default. If using battery power, the brightness setting is set to its middle level by default.
POINT
The higher the brightness level, the more power the LifeBook notebook will consume and the faster your batteries will discharge. For maximum battery life, set the brightness level as low as possible.
Using the BatteryAid Utility (Windows 2000 only)
Adjusting the brightness using the Power Management Utility changes the setting permanently.
1. Double-click the Battery Icon in the lower right corner of your display (it looks like a small battery with a leaf extending from the top). This will open the BatteryAid Properties dialog box.
2. Click on the Fujitsu BatteryAid 2/2 tab and adjust your LCD Backlighting to the desired level.
3. Click OK or Apply to permanently change the settings.
You may need to readjust the brightness level periodi­cally depending on your operating environment.
CLOSING THE DISPLAY PANEL
1. Holding the edge of your display panel, pull it forward until it is flush with the body of your LifeBook notebook.
2. Push down until you hear a click. This will engage the locking mechanism and prevent your display panel from opening unexpectedly.
30
Getting Started
Starting Your LifeBook Notebook
POWER ON
Power and Suspend/Resume Button
The Power and Suspend/Resume button is used to power on your LifeBook notebook, to resume from Standby or Save-to-Disk mode, to place your notebook in Standby or Save-to-Disk mode or to power off. You can also turn off your notebook by choosing Shut Down from the Windows Start menu.
Power/ Suspend/ Resume Button
Figure 3-3 Powering Up the System
Once you have connected your AC adapter or charged the internal Lithium ion Battery, you can press this button to Power On your LifeBook notebook.
(Figure 3-3)
POINT
When you turn on your LifeBook notebook be sure you have a power source. This means that at least one battery is installed and charged, or that the AC or Auto/ Airline adapter is connected and has power.
CAUTION
Do not carry your LifeBook notebook around with the power on or subject it to shocks or vibration, as you risk damaging your notebook.
When you Power On your notebook, it will perform a Power On Self Test (POST) to check the internal parts and configuration for correct functionality. If a fault is found, your notebook will emit an audio warning and/ or an error message will be displayed. (See Power On Self Test Messages on page 64 for more information) Depending on the nature of the problem, you may be
able to continue by starting the operating system or by entering the BIOS setup utility and revising the settings.
After satisfactory completion of the Power On Self Test (POST), your LifeBook notebook will load your oper­ating system.
POINT
Never turn off your LifeBook notebook during the Power On Self Test (POST) or it will cause an error message to be displayed when you turn your notebook on the next time.
(See Power On Self Test Messages on
page 64 for more information)
BOOT SEQUENCE
The procedure for starting-up your Fujitsu LifeBook notebook is termed the Bootup sequence and involves your notebook’s BIOS. When your notebook is first turned on, the main system memory is empty, and it needs to find instructions to start up your notebook. This information is in the BIOS program. Each time you power up or restart your notebook, it goes through a boot sequence which displays a Fujitsu logo until your operating system is loaded. During booting, your note­book is performing a standard boot sequence including a Power On Self Test (POST). When the boot sequence is completed without a failure and without a request for the BIOS Setup Utility, the system displays the operating system’s opening screen.
The boot sequence is executed when:
You turn on the power to your LifeBook notebook.
You restart your LifeBook notebook from the Windows Shut Down dialog box.
The software initiates a system restart. Example: When you install a new application.
You reset the system by pressing the three keys [CTRL+ALT+DEL].
BIOS SETUP UTILITY
The BIOS Setup Utility is a program that sets up the operating environment for your LifeBook notebook. Your BIOS is set at the factory for normal operating conditions, therefore there is no need to set or change the BIOS’ environment to operate your LifeBook note­book.
The BIOS Setup Utility configures:
Device control feature parameters, such as changing I/O addresses and boot devices.
System Data Security feature parameters, such as passwords.
31
LifeBook E Series Notebook – Section 3
Entering the BIOS Setup Utility
To enter the BIOS Setup Utility do the following:
1. Turn on or restart your LifeBook notebook.
2. Press the [F2] key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS Setup Utility with the current settings displayed.
3. Press the [RIGHT ARROW] or [LEFT ARROW] key to scroll through the other setup menus to review or alter the current settings. Additional navigational information is located at the bottom of the BIOS screen.
BIOS Guide
A guide to your LifeBook notebook’s BIOS is available online. Please visit our service and support Web site at www.fujitsupc.com/support. Once there, select Support, then select Notebooks under User’s Guides. Select Life­Book BIOS Guides from the pull-down menu for your LifeBook series. If you are unsure of your notebook’s BIOS number, refer to your packing slip.
POINT
If your data security settings require it, you may be asked for a password before the BIOS main menu will appear.
BOOTING THE SYSTEM
We strongly recommend that you do not attach any external devices and do not put a CD or floppy disk in any drive until you have gone through the initial power on sequence.
When you turn on your LifeBook notebook for the first time, it will display a Fujitsu logo on the screen. If you do nothing, the system will load the operating system, and then the Windows Welcome will begin.
Designed to accommodate the needs of users in many different countries, Windows needs to be configured the first time you use it. Windows has three parts:
Getting Started: You have the opportunity to enter custom information for your configuration file and setup your modem so that your LifeBook notebook will be prepared to dial out.
Registration: Easy online registration for Windows with Microsoft, and for your LifeBook notebook with Fujitsu.
Windows License Agreement and Final Settings: You have the opportunity to review the Windows License Agreement.
POINT
You may click Cancel at any time within this process to shut down Windows. You may restart this process at any time in the future, but you must complete it in order to use your computer.
Getting Started
Read the instructions on the screens carefully and fill in the information as directed. You will be asked for such items as the language you wish to use, the country in which you live, your first and last name, and about how you dial out from where you will be using your LifeBook notebook. For the modem settings, enter your current location information where you will be using your Life­Book notebook. If you are not connected to a phone line and plan to register at a later time, you may click the Skip button, and you will go directly to the condition of use page.
Once you have set up your LifeBook notebook to dial out, Windows will make a free telephone call to test the settings. If the call is unsuccessful, you will be returned to the phone settings page where you may try to fix them. If you are unable to fix the settings please contact Fujitsu Service and Support. (See Fujitsu Contact Infor- mation on page 1 for more information). If you would simply like to move on, and register at a later time, you may click the Skip button, and you will go directly to the Condition of Use page.
Windows Registration
If your connection is successful, you will go to a Registration Confirmation page. Enter the requested information, then check the box at the bottom to register your copy of Wind ows wit h Microsoft. Once you have finished, click the Next button to continue.
Final Settings
The first part of your final settings is the Windows End User License Agreement. Read the agreement carefully. When you finish reading you must accept or reject the terms of the agreement and then click on the Next button.
POINTS
If you reject the terms of the license agreement you will be asked to review the license agreement for information on returning Windows or to shut down your LifeBook notebook.
You cannot use your LifeBook notebook until you have accepted the License Agreement. If you stop the process your notebook will return to the beginning of the Windows Welcome Process, even if you shut your notebook down and start it up again.
32
REGISTERING YOUR LIFEBOOK NOTEBOOK
What are the benefits of registering?
You will receive an identification label for your LifeBook notebook, which, if your notebook is ever lost, may help in getting it returned to you. You will also receive tech­nical support access and useful product mailings.
How do I register my LifeBook notebook?
You can register your LifeBook by going to our Web site:
www.fujitsupc.com/support
You will need to be set up with an Internet Service Provider (ISP) to use the last option.
INSTALLING CLICK ME!
The first time you boot up your system, you will see an icon called Click Me! on the desktop. When you click the icon, your system will automatically build the icon tray in the bottom right of the screen. These icons provide links to utilities that you will frequently access.
The icon is automatically deleted after you launch Click Me! and restart the system.
Getting Started
33
LifeBook E Series Notebook – Section 3

Power Management

Your LifeBook notebook has many options and features for conserving battery power. Some of these features are automatic and need no user intervention, such as those for the internal modem. However, others depend on the parameters you set to best suit your operating condi­tions, such as those for the display brightness. Internal power management for your LifeBook notebook may be controlled from settings made in your operating system or from settings made in the BIOS setup utility.
Besides the options available for conserving battery power, there are also some things that you can do to prevent your battery from running down as quickly. For example, you can create an appropriate power saving profile, put your notebook into Suspend mode when it is not performing an operation, and you can limit the use of high power devices. As with all mobile, battery powered computers, there is a trade-off between performance and power savings.
POWER AND SUSPEND/RESUME BUTTON
When your LifeBook notebook is active, the Power and Suspend/Resume button can be used to manually put your notebook into Suspend mode. Push the Power and Suspend/Resume button when your notebook is active, but not actively accessing anything, and immediately release the button. You will hear two short beeps and your system will enter Suspend mode.
If your notebook is suspended, pushing the Power and Suspend/Resume button will return your notebook to active operation. You can tell whether or not your system is in Suspend mode by looking at the Power indi­cator. (See Figure 2-8 on page 13 for location) If the indi­cator is visible and not flashing, your LifeBook notebook is fully operational. If the indicator is both visible and flashing, your notebook is in Suspend mode. If the indi­cator is not visible at all, the power is off or your note­book is in Save-to-Disk mode. (See Save-to-Disk Mode)
SUSPEND MODE
Suspend or Standby mode in Windows 2000 Profes­sional saves the contents of your LifeBook notebook’s system memory during periods of inactivity by main­taining power to critical parts. This mode will turn off the CPU, the display, the hard drive, and all of the other internal components except those necessary to maintain system memory and allow for restarting. Your LifeBook notebook can be put in Suspend mode by:
Pressing the Power/Suspend/Resume button when your system is turned on.
Selecting Standby from the Windows Shut Down menu.
Timing out from lack of activity.
Allowing the battery to reach the Dead Battery Warning condition.
Your LifeBook notebook’s system memory typically stores the file(s) on which you are working, open appli­cation(s) information, and any other data required to support the operation(s) in progress. When you resume operation from Suspend mode, your LifeBook notebook will return to the point where it left off. You must use the Power and Suspend/Resume button to resume opera­tion, and there must be an adequate power source avail­able, or your LifeBook notebook will not resume.
POINTS
If you are running your LifeBook notebook on battery power, be aware that the battery continues to dis­charge while your LifeBook notebook is in Suspend mode, though not as fast as when fully operational.
Disabling the Suspend/Resume button prevents it from being used to put your LifeBook notebook in Suspend or Save-to-Disk mode. The resume function of the button cannot be disabled.
The Suspend or Hibernation (Save-to-Disk) mode should not be used with certain PC Cards. Check your PC Card documentation for more information.
When PC Cards or external devices are in use, Hibernation (Save-to-Disk) mode cannot return to the exact state prior to suspension because all of the peripheral devices will be re-initialized when the system re-starts.
If your LifeBook notebook is actively accessing infor­mation when you enter the Suspend or Hibernation (Save-to-Disk) mode, changes to open files are not lost. The files are left open and memory is kept active during Suspend mode, or the memory is transferred to the internal hard drive during Hibernation mode.
The main advantage of using the Hibernation (Save­to-Disk) function is that power is not required to maintain your data. This is particularly important if you will be leaving your LifeBook notebook in a sus­pended state for a prolonged period of time. The drawback of using Hibernation mode is that it length­ens the power down and power up sequences and resets peripheral devices.
Your system is set to use the Max Battery power scheme when running on battery power. If you change the power scheme to a different profile, your battery life may vary.
34
Getting Started
POINT
Save-to-Disk mode requires allocating a significant amount of hard drive capacity for saving all system memory, which reduces your usable disk space. When you purchase your LifeBook notebook it will have space allocated for the memory installed. If you upgrade the original system by adding a memory upgrade module without changing the size of your Save-to-Disk allocation you will get an error message when you try to activate Save-to-Disk mode and it will not work.You can download the Save-to-Disk File Allocation information from our Web site at
f you need help, contact your support representative
I
for recommendations.
www.fujitsupc.com.
HIBERNATION (SAVE-TO-DISK) FEATURE
The Hibernation feature saves the contents of your LifeBook notebook’s system memory to the hard drive as a part of the Suspend/Resume mode. You can enable or disable this feature.
Enabling or Disabling the Hibernation Feature
The default setting is not enabled. To enable or disable the Hibernation feature follow these easy steps:
1. From the Start menu, select Settings, and then select Control Panel.
2. From the Control Panel, select Power Management.
3. Select Hibernation tab. Select the box to enable or disable this feature.
Using the Hibernation Feature
1. From the Start menu, select Settings, and then select Control Panel.
2. From the Control Panel, select Power Management
-> Power Options.
3. Select Advanced tab, then select Hibernate from the pull-down menu for Power buttons.
DISPLAY TIMEOUT
The Video Timeout is one of the power management parameters. This feature saves power by turning off the display if there is no keyboard or pointer activity for the user selected timeout period. Any keyboard or pointer activity will cause the display to restart automatically. This feature is independent of the Power and Suspend/ Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS Setup Utility
on page 31 for more information)
HARD DISK TIMEOUT
The Hard Disk Timeout is another one of the power management parameters. This feature saves power by turning off the hard drive if there is no hard drive activity for the user selected timeout period. Any
attempt to access the hard drive will cause it to restart automatically. This feature is independent of the Power and Suspend/Resume button and can be enabled and disabled in Windows and BIOS setup utility. (See BIOS
Setup Utility on page 31 for more information)
RESTARTING THE SYSTEM
If your system is on and you need to restart it, be sure that you use the following procedure.
1. Click the Start button, and then click Shut Down.
2. Select the Restart option from within the Windows
Shut Down dialog box.
3. Click OK to restart your LifeBook notebook. Your
notebook will shut down and then reboot.
POINT
Turning off your LifeBook notebook without exiting Windows or turning on your notebook within 10 seconds of the notebook being shut off may cause an error when you start the next time.
CAUTION
Never turn your LifeBook notebook off while an application is running. Be sure to close all files, exit all applications, and shut down your operating system prior to turning off the power with the power/suspend/ resume button. If files are open when you turn the power off, you will lose any changes that have not been saved, and may cause disk errors.
POWER OFF
Before turning off the power by choosing Shut Down from the Windows 2000 Professional Start menu, check that the Hard Drive, DVD, CD-ROM, CD-RW, PC Card and the Floppy Disk Drive Access indicators are all Off. (See Figure 2-8 on page 13) If you turn off the power while accessing a disk or PC Card there is a risk of data loss. To assure that your LifeBook notebook shuts down without error, use the Windows shut down procedure.
Using the correct procedure to shut down from Windows allows your LifeBook notebook to complete its operations and turn off power in the proper sequence to avoid errors. The proper sequence is:
1. Click the Start button, and then click Shut Down.
2. Select the Shut Down option from within the
Windows Shut Down dialog box.
3. Click OK to shutdown your LifeBook notebook.
If you are going to store your notebook for a month or more see Care and Maintenance Section.
35
LifeBook E Series Notebook – Section 3
36
4
User-Installable Features
37
LifeBook E Series Notebook – Section 4
38

User-Installable Features

Lithium ion Battery

Your Fujitsu LifeBook notebook has a Lithium ion battery that provides power for operating your note­book when no external power source is available. The rechargeable battery is durable and long lasting, but should not be exposed to extreme temperatures, high voltages, chemicals or other hazards.
The Lithium ion battery operating time may become shorter if it is used under the following conditions:
Your system is set to use the Max Battery power scheme when running on battery power. If you change the power scheme to a different profile, your battery life may vary.
When used at temperatures that exceed a low of 5°C (40°F) or a high of 35°C (95°F). Extreme temperatures not only reduce charging efficiency, but can also cause battery deterioration. The charging icon on the Status Indicator panel will flash when you try to charge a battery that is outside its operating temperature range. (See Battery Charging Indicators on
page 14 for more information)
When using a high current device such as a modem, media drive, or the hard drive, using the AC adapter will conserve your battery life.
RECHARGING THE BATTERIES
If you want to know the condition of the primary Lithium ion battery, check the Battery Level indicator located on the Status Indicator panel. The indicator changes as the battery level changes.
The Lithium ion battery is recharged internally using the AC adapter or Auto/Airline adapter. To recharge the battery make sure the battery that needs to be charged is installed in your LifeBook notebook and connect the AC or Auto/Airline adapter.
POINT
Make sure that the Battery Charging indicator and the percentage charge is shown inside the Battery Level icon on the Status Indicator Panel.
There is no memory effect on the Lithium ion battery therefore you do not need to discharge the battery completely before recharging. The charge times will be significantly longer if your LifeBook notebook is in use while the battery is charging. If you want to charge the battery more quickly, put your LifeBook into Suspend mode, or turn it off while the adapter is charging the battery. (See Power Management on page 34 for more
information on Suspend mode and shutdown procedure)
CAUTION
Do not leave a faulty battery in your LifeBook note­book. It may damage your AC adapter, optional Auto/Airline adapter, another battery or your note­book itself. It may also prevent operation of your notebook by draining all available current into the bad battery.
Under federal, state, or local law it may be illegal to dispose of batteries by putting them in the trash. Please take care of our environment and dispose of batteries properly. Check with your local government authority for details regarding recycling or disposing of old batteries. If you cannot find this information elsewhere, contact your support representative at 1-800-8FUJITSU (1-800-838-5487).
POINT
Actual battery life will vary based on screen brightness, applications, features, power management settings, battery condition and other customer preferences. Media drive or hard drive usage may also have a significant impact on battery life. Battery charging capacity is reduced as the battery ages. If your battery is running low quickly, you should replace it with a new one.
POINT
Using heavy current devices such as a Modem or frequent DVD or CD-RW accesses may prevent complete charging.
Low Battery State
When the battery is running low, a low battery notifica­tion message will appear. If you do not respond to the low battery message, the batteries will continue to discharge until they are too low to operate. When this happens, your LifeBook notebook will go into Suspend mode. There is no guarantee that your data will not be lost once the notebook reaches this point.
CAUTION
To prevent loss of data, you should save all your active data and put your LifeBook notebook into Suspend mode when the low battery message first appears, until you can provide a new power source. When you are in Suspend mode, there must always be at least one power source active. If you turn off the power with the power/suspend/resume button, or remove all power sources while your LifeBook notebook is in Suspend mode, any data that has not been saved to the hard drive will be lost.You should provide power to your notebook from a charged battery, an AC power adapter, or Auto/Airline as soon as possible.
39
LifeBook E Series Notebook – Section 4
Dead Battery Suspend mode shows on the Status indi­cator just like the normal Suspend mode. Once your LifeBook notebook goes into Dead Battery Suspend mode you will be unable to resume operation until you provide a source of power either from an adapter, or a charged battery. Once you have provided power, you will need to press the Suspend/Resume button to resume operation. In the Dead Battery Suspend mode, your data can be maintained for some time, but if a power source is not provided promptly, the Power indicator will stop flashing and go out, meaning that you have lost the data that was not stored. Once you provide power, you can continue to use your LifeBook notebook while an adapter is charging the battery.
Shorted Batteries
The Status Indicator panel uses a symbol inside the battery outline of the Battery Level indicator to display the operating level available in that battery. (See Figure 2-9 on page 14) If this display shows a Shorted Battery, it means that the battery is damaged and must be replaced so it does not damage any other parts of your LifeBook notebook.
REPLACING THE BATTERY
With the purchase of an additional battery, you can have a fully charged spare to swap with one that is not charged.
Battery Release Latches
Figure 4-1 Replacing the Battery
Follow the steps below to replace a battery (Figure 4-1):
1. Have a charged battery ready to install.
2. Shut down your notebook and disconnect the AC adapter.
3. Press the battery release latches toward the battery.
4. Lift the battery by the latch end and remove it from the bay.
5. Slide a charged battery into the bay and press it down until the latches click into place.
6. Plug in the AC adapter and turn the power on.
40
Figure 4-2 Loading/Ejecting a 3.5” Floppy Disk

External USB Floppy Disk Drive

An external USB floppy disk drive is available as an option for your LifeBook notebook. The external floppy disk drive can read and write information on removable
1.44MB and 720KB floppy disks.
POINT
Your LifeBook notebook is preconfigured to boot from a USB floppy drive. Reference the BIOS manual for fur­ther information on changing the default boot drive. The BIOS manual can be found on the Fujitsu PC web site: www.FujitsuPC.com, under Support.
LOADING A DISK
To load a disk into your disk drive, follow these easy steps:
1. Orient the disk so that its label is facing upwards and the shutter side is pointing towards the drive.
(Figure 4-2)
2. Push the disk into the drive until the Eject button pops out and you hear a click.
User-Installable Features
Eject Button
CAUTION
If you eject the disk while the Floppy Disk Drive Access indicator is active, there is a risk of damaging the data on the disk, the disk itself or even the disk drive.
PREPARING A DISK FOR USE
Before you can use a new disk, it needs to be prepared so your LifeBook notebook knows where to store infor­mation. This preparation is called formatting or initial­izing a disk. You will need to format new disks, unless they are preformatted. (Please refer to your operating
system manual for step-by-step instructions on formatting a disk)
To prevent accidental erasure of the data stored on a disk, slide the “write protect” tab until a small hole is exposed. This sets the disk into a protected state where nothing can be added or removed. If you want to add or remove data on a protected disk, slide the “write protect” tab to close the small hole. (Figure 4-3)
Write Enabled
POINT
When there is no disk in the drive, the Eject button is flush with your notebook.
EJECTING A DISK
To eject a disk from the disk drive, follow these easy steps:
1. Check that the Floppy Disk Drive Access indicator is inactive.
2. Press the Eject button. This will push your disk partially out of the drive.
3. Remove the disk.
Write Protected
Figure 4-3 Floppy Disk Write Protect
CAUTION
Formatting a floppy disk that already contains data will erase all of the information on the disk.
41
LifeBook E Series Notebook – Section 4
Figure 4-4. Media Player Drive
DVD/CD Eject Button
DVD/CD Holder Tray

Media Drive

Your Fujitsu LifeBook notebook contains a media player drive which is either a CD, DVD, or DVD/CD-RW combo player. A DVD drive gives you access to movie, software, and audio DVD/CDs. A DVD/CD-RW drive allows you to write data onto recordable CDs in addition to all of the standard DVD drive functions.
MEDIA PLAYER SOFTWARE
DVD model only: With the media player drive and media player software you can play DVD movies on your Life­Book notebook. The media player includes controls which allow you to take full advantage of the features of a DVD movie, as well as standard features such as fast forward, fast reverse, pause, etc.
DVD/CD-RW Combo model only: With the combo drive, you can play DVD movies, read audio CDs, and write data onto recordable CD-R or CD-RW discs.
POINTS
Prior to using your Media Player, you must install the Media Player software. Refer to the applicable
readme file on the Driver Applications CD-ROM for instructions on installing you Media Player software.
You should periodically check the Fujitsu Web site at www.fujitsupc.com for current updated drivers.
Prolonged use of the media player drive, such as watching a DVD movie, will substantially reduce your battery life.
LOADING MEDIA
To load a disc into your media player drive, follow these steps:
1. Push and release the eject button on the front of the media player drive to open the holder tray. The tray will come out of the notebook a short distance.
2. Gently pull the tray out until a media disc can easily be placed in the tray.
CAUTION
There may be a protective sheet in the tray from when it was shipped; please make sure it is removed before oper­ating the drive, otherwise your drive may be damaged.
3. Place the media into the tray, label side up, with the hole in the center of the disc. Snap the disc onto the raised circle in the center of the tray.
4. Gently push the holder tray back in until you hear a click. (Figure 4-5)
POINT
If you have disabled the Auto Insert Notification Function, you will have to start the drive from your desktop, since your notebook will not automatically recognize that media has been loaded.
CAUTION
Do not operate your media player drive unless your LifeBook notebook is sitting on a flat surface. Using a drive when the system is not level may damage the drive or prevent proper operation.
42
Figure 4-5 Loading/Ejecting Media
User-Installable Features
REMOVING MEDIA
1. Push and release the eject button on the front of the media player drive. This will stop the drive and the holder tray will come out of the notebook a short distance.
2. Gently pull the tray out until the disc can easily be removed from the tray.
3. Carefully remove the media disc from the holder tray.
4. Gently push the holder tray back in until you hear a click.
EMERGENCY DVD/CD-ROM TRAY RELEASE
If for some reason the eject button fails, you can open the DVD/CD-ROM tray with a paper clip or your pen inserted into the eject hole in the far right side of the front of the tray. Straighten one side of a paper clip and push it gently into the hole. The tray will pop out a short distance.
Starting a DVD Movie (DVD Models only)
1. Insert the DVD movie into the media player drive of your notebook. If the CD AutoRun feature activates, skip Step 2.
2a.Windows 2000 only: From the Start menu, select
Programs, then select InterVideo WinDVD and click InterVideo WinDVD . This will launch the DVD movie.
2b. Windows XP only: The first time you insert a movie
into the DVD/CD-RW tray, you will be prompted to select what you want the system to do when discs are inserted (e.g., start automatically or wait for a prompt). Until you make a selection, you will receive the same prompt whenever you insert a disc.
3. Click OK to close the About DVD Player Performance dialog box and the movie will begin.
Opening the DVD/CD-RW Drive Control Panel
With most DVD-ROMs, you have the option of altering how the movie should play and what you wish to view. You can do this by using the DVD/CD-RW Combo Drive control panel and the mouse.
1. Right-click on the movie screen to open a dropdown menu for options.
2. Select View, then Player for all the controls available. This will open the control panel into the bottom of the screen.
Figure 4-6 Emergency Removal of a CD/DVD
USING THE MEDIA PLAYER SOFTWARE
POINTS
Prior to using your Media Player, you must install the Media Player software.
For details on using your media player, consult the Help file that accompanies the software.
Using the Media Player Control Panel
The Media Player software allows you to watch the movie much like a VCR player. You have the option to pause, rewind, fast-forward and stop the movie at any point.
1. To Pause the movie, click the button.
2. To Rewind the movie, click the button to rewind to a specific portion of the movie, or the button to return to the opening screen.
3. To Fast-forward the movie, click the button to forward to a specific portion of the movie, or the button to jump to the ending credits.
43
LifeBook E Series Notebook – Section 4
4. To Stop the movie, click the button.
Exiting the Media Player
1. Click on the U located in the upper right corner of the title bar. This will open a Media Player dialog box.
2. Click Ye s to stop and exit the movie, or No to close the Media Player dialog box and return to the movie.
USING DOLBY
TM
HEADPHONE
The Dolby Headphone utility lets you enjoy multi­channel sound sources, such as movies, with realistic surround sound using your conventional stereo head­phones.
Dolby Headphone is a signal processing system that enables your stereo headphones to realistically portray the sound of a five-speaker playback system.
POINTS
Media discs which do not have the Dolby Surround 5:1 symbol will not support Dolby Headphone.
After making changes to the Dolby Headphone feature and clicking OK, wait at least ten seconds before making another change in order to allow the system to stabilize.
To use the Dolby Headphone feature, perform the following steps:
1. Insert the disc in the media player tray. When you do so, WinDVD will start automatically.
2. Place your cursor over the Fujitsu logo on the WinDVD cotrol panel and click on it. If the disc supports Dolby Surround 5.1, a drop down menu appears.
3. Verify that Dolby headphones is checked on the menu. If you do not want it active, select Disable.
USING THE MEDIA PLAYER ON BATTERY POWER
Since media player drives consume a lot of power, your overall battery life will be shorter when operating the media player drive continuously (such as watching a DVD movie). Many movie run-times are longer than your LifeBook notebook can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety.
POINTS
Prolonged use of the media player drive, such as watching a DVD movie, will substantially reduce your notebook’s battery life.
Many movie run-times are longer than your system can support on a single battery. If you are watching a DVD movie on battery power you may need to swap in an additional, charged battery or attach AC power during the movie to view it in its entirety.
An additional fully-charged battery is highly recom­mended if you will be watching DVD movies on bat­tery power. If you don’t have an additional battery, you may purchase one either on-line at www.fujit­supc.com or call 1-877-372-3473.
To Watch a Movie on Battery Power:
1. Have an additional fully-charged battery or your AC adapter ready for use.
2. Start watching your DVD movie.
3. When the low battery warning occurs, immediately stop the movie and exit the media player.
CAUTION
If you do not stop the media player quickly and the LifeBook notebook attempts to auto-suspend (critical battery low state) the notebook will shut down improperly. If this occurs, you will need to perform a hard reset and follow the instruction, if any, presented to you before the system will reboot.
4. Manually place your notebook into suspend mode by depressing the Suspend button. Plug in a power adapter and replace the discharged battery with an additional fully-charged battery. If you do not have an additional battery, you may use the AC power adapter as your power source to continue watching the movie while recharging the installed battery.
5. Resume your notebook by pressing the Suspend button again. This step is not required if you attached AC power without entering suspend mode.
6. Restart your media player, locate and skip to the chapter of the movie you were last watching.
7. Continue watching your DVD movie.
POINT
Some shorter DVD movies may not require you to swap batteries or attach AC power to complete them. However, it is best to be prepared since actual battery life while operating the media player drive cannot be guaranteed.
44
AUTO INSERT NOTIFICATION FUNCTION
The Auto Insert Notification function allows your Life­Book notebook to automatically start a DVD/CD as soon as it is inserted in the media player drive and the tray is closed. Your notebook will begin playing an audio DVD/ CD or will start an application if the DVD/CD includes an auto run file.
To prevent a CD from playing automatically as soon as it is inserted, refer to the related help file for your specific operating system.
User-Installable Features
45
LifeBook E Series Notebook – Section 4

Hard Disk Drive

Your Fujitsu LifeBook notebook hard disk drive capacity is dependent on which model you are using. Some Life­Book notebooks may also contain a removable hard disk drive in addition to the internal hard disk drive. (See
Specifications on page 77 for more information)
FORMATTING THE HARD DISK DRIVE
The internal hard disk drive is formatted, or initialized, at the factory. You do not need to format it under normal circumstances. If you decide to reformat due to corruption or upgrade, please refer to your operating system documentation for the correct procedure.
CAUTION
Reformatting the hard disk drive will erase all of the data currently stored on it, including the operating system and installed programs.
Before you reformat your hard disk drive, please note:
Any data that currently resides on your hard disk drive must be backed-up to floppy disks or other data storage media, or it will be permanently lost. These back-up disks can then be used to reinstall and restore your data. (See your operating system manual for more
information on backing-up your data files)
All application software that is installed on the hard disk drive, must be reinstalled from the original source.
The factory-installed software, including the operating system, can be restored using the Drive Image Special Edition (DISE) software that came with your LifeBook notebook (See Drive Image Special Edition (DISE) on page 66 for more information).
46
PC Card
User-Installable Features
PC Card Slots
Eject Button
Figure 4-7 Installing/Removing PC Cards

PC Cards

Your LifeBook notebook supports two Type I and II and one Type III PC Cards, which can perform a variety of functions depending on which type of PC Card you install.
Some types of PC Cards available on the market include:
Fax/data modem
Local area network (LAN)
Wireless LAN PC card
IDE solid-state disk
SCSI
Other PC Cards that conform to PCMCIA™ 2.1 or CardBus standards.
For further information, refer to the instructions supplied with your PC Card.
INSTALLING PC CARDS
PC Cards are installed in the PC Card slots. To install a PC Card, follow these easy steps:
CAUTIONS
Installing or removing a PC Card during your LifeBook notebook’s shutdown or bootup process may damage the card and/or your notebook.
Do not insert a PC Card if it not clean and dry. Insert­ing a dirty or wet card could damage your notebook.
1. See your PC Card manual for specific instructions on the installation o f your card. Some PC Cards may require your LifeBook notebook to be Off while installing them.
2. Make sure there is no PC Card currently occupying the slot. If there is, see Removing PC Cards.
3. If either of the eject buttons is extended, press it in until it clicks.
4. Insert your PC Card into the slot with the product label facing up.
5. Push the card into the slot firmly until it is seated in the opening.
REMOVING PC CARDS
To remove a PC Card, perform the following steps:
1. See your PC Card manual for specific instructions on removing your card. Some PC Cards may require your notebook to be Off while removing them.
CAUTION
Loss of data could occur if proper shutdown procedures are not observed.
Windows 2000 Professional PC Cards should be
stopped using the Unplug or Eject Hardware utility on the taskbar. Refer to your operating system manual for the correct procedure.
Windows XP has a Safe Removal of Hardware utility on the taskbar. Refer to your operating system manual for the correct procedure.
POINT
If the dialog box states that the device cannot be removed, you must save all of your open files, close any open applications and shut down your LifeBook notebook. Once your notebook has been shut down, you must turn Off the power using the power/suspend/ resume button.
47
LifeBook E Series Notebook – Section 4
2. Unlock the PC Card from the slot by first pressing the eject button associated with the slot the card is in. When pressed, the button will pop up.
3. Firmly press the button again until it is flush with the notebook. This will push the PC Card slightly out of the slot allowing you to remove the card.
CAUTION
If the PC Card has an external connector and cable, do not pull the cable when removing the card.
SMARTCARD READER
An embedded SmartCard Reader is provided on your LifeBook notebook. SmartCards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of different information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security informa­tion, and provide personal identification and informa-
tion.
POINT
In order to use the embedded SmartCard Reader, you must purchase an optional SmartCard adapter for installation into an available Type II PC Card slot. For more information, visit our online store at www.fujitsupc.com.
48

Memory Upgrade Module

Your LifeBook notebook comes with 128MB or 256MB of memory factory installed. To increase your LifeBook notebook’s memory capacity, you may install an addi­tional memory upgrade module. You can also replace the original memory module with a higher capacity module. The memory upgrade must be a PC2100 DDR266 SO­DIMM module, but it can be any capacity up to 1024MB (total). To ensure 100% compatibility, we recommend that you only purchase additional memory from the Fujitsu on-line accessory store at: www.fujitsupc.com/accessories.
CAUTION
Do not remove any screws from the memory upgrade module compartment, except the ones specifically shown in the directions for installing and removing the memory upgrade module.
INSTALLING A MEMORY UPGRADE MODULE
1. Turn off power to your LifeBook notebook using the power/suspend/resume button, and remove any power adapter (AC or auto/airline).
2. Make sure that all the connector covers are closed.
3. Turn the LifeBook notebook bottom side up, with the front panel toward you.
4. Remove the screw at the front of the memory upgrade module compartment. (Figure 4-8)
5. Remove the cover by tilting the front edge up and then pulling forward until the tabs on the cover are free.
User-Installable Features
CAUTION
The memory upgrade module can be severely damaged by electro-static discharge (ESD). Be sure you are properly grounded when handling and installing the module.
6. Remove the memory upgrade module from the static guarded sleeve.
7. Align the memory upgrade module with the part side up. Align the connector edge of the memory upgrade module with the connector slot in the compartment. The connector will be pointing toward the rear of the LifeBook notebook.
8. Insert the memory upgrade module at a 45° angle. Press the connector edge of the module firmly down and into the connector until it lodges under the retaining clip. You will hear a click when it is prop­erly in place. (Figure 4-9)
Figure 4-9. Installing a Memory Upgrade Module
9. Replace the cover by hooking the tabs under the rear edge of the compartment opening and tilting down until flush with the bottom of your LifeBook note­book.
10. Replace the screw.
Slot 2
Slot 1
Figure 4-8. Opening the Memory Upgrade Compartment
POINT
If you use only one memory module in your system, be sure it is installed in Slot 2. Slot 2 is the slot that is further away from the edge of the system.
(Figure 4-8)
POINT
The memory upgrade module is not something you should routinely remove from your notebook. Once it is installed, you should leave it in place unless you want to increase system memory capacity.
REMOVING A MEMORY UPGRADE MODULE
1. Perform steps 1 through 5 of Installing a Memory Upgrade Module.
2. Pull the clips sideways away from each side of the memory upgrade module at the same time.
3. While holding the clips out, remove the module from the slot by lifting it up and pulling towards the rear of your LifeBook notebook. (Figure 4-10)
49
LifeBook E Series Notebook – Section 4
Figure 4-10. Removing a Memory Upgrade Module
4. Store the memory upgrade module in a static guarded sleeve.
5. Replace the cover by following steps 9 and 10 of Installing a Memory Upgrade Module.
POINT
After installing your added memory module, you must complete the Resetting the Save-to-Disk Parameters procedure in order for the Save-to-Disk mode to operate properly on your LifeBook notebook.
(See Hibernation (Save-to-disk) Feature on page 35 for more information)
2. Allow the system to start booting and press the F2 key once the Fujitsu logo appears on the screen. This will open the main menu of the BIOS setup. Tap on [Info] at the top of the screen. The current settings will be displayed. (See BIOS Setup Utility on page 31
for more information)
The System Memory and the Extended Memory capacity, as detected by your LifeBook notebook during the Power On Self Test (POST), are displayed at the bottom of the main menu screen. The chart below shows you the possible displays that can be shown on the main menu screen. In the chart, Slot 2 is the original DR266 memory slot, while Slot 1 is the upgrade slot. (See Figure 4-8 on page 49 for location).
POINT
If the total memory displayed is incorrect, check that your memory upgrade module is properly installed. (If the module is properly installed and the capacity is still not correctly recognized, see the Troubleshooting section starting on page 55)
Installed
CHECKING THE COMPUTER RECOGNITION OF NEW MEMORY CAPACITY
Once you have changed the system memory capacity by either adding or removing a memory upgrade module, be sure to check that your notebook has recognized the change.
You can check the memory capacity by looking at the main menu of the BIOS setup:
1. Turn on the power to your LifeBook notebook using the power/suspend/resume button.
Slot 2 Slot 1 Total RAM Installed
128MB 0MB 128MB 128MB 128MB 256MB 128MB 256MB 384MB 256MB 0MB 256MB 256MB 128MB 384MB 256MB 256MB 512MB 512MB 128MB 640MB 512MB 256MB 768MB 512MB 512MB 1024MB
50

Device Ports

Your LifeBook notebook comes equipped with multiple ports to which you can connect an external device including: disk drives, keyboards, modems, printers, etc.
COMMUNICATIONS PORTS
Your LifeBook has a Modem jack (RJ-11) and a LAN jack (RJ-45) to accommodate external communications.
Modem (RJ-11) Telephone Jack
The modem (RJ-11) telephone jack is used for your internal modem. To connect the telephone cable follow these easy steps: (See Figure 2-4 on page 9 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Plug the other end of the telephone cable into a telephone outlet.
CAUTION
Do not connect the internal modem to a Digital PBX as it may cause serious damage to the modem or your LifeBook notebook. It should be noted that some hotels use the Digital PBX systems, please be sure to find out BEFORE you connect your modem. Consult your PBX manufacturer’s documentation for more information.
POINT
The internal modem is designed to the ITU-T V.90 standard. Its maximum speed of 53000bps is the highest allowed by the FCC, and its actual connection rate depends on the line conditions. The maximum speed is 33600bps at upload.
LAN PORT
This port allows you to connect a LAN (RJ-45) cable for high-speed network or broadband connections (e.g., DSL, cable modem). When your LifeBook notebook is connected to the Port Replicator, the LAN port on the system is not accessible; the Port Replicator LAN port is the only one that should be used when it as attached to the system. (See Figure 2-4 on page 9 for location)
WIRELESS LAN PORT
The optional Wireless LAN port allows you to connect with another device wirelessly. (See Integrated Wireless
LAN* User’s Guide on page 95 for more information)
IEEE 1394 JACK
The 4-pin IEEE 1394 jack allows you to download digital files (such as digital video and images) to the computer at up to 400Mbps. Hot-swappable and plug-n-play, it is much faster than USB, CardBus, or parallel port. In order to connect a 1394 device, follow these steps: (See
Figure 2-3 on page 8 for location)
User-Installable Features
POINT
The 1393 port in this system uses a four-pin configuration. If you intend to interface with devices which have a six-pin configuration, you will need to purchase an adapter.
PARALLEL PORT
The parallel port, or LPT port, allows you to connect parallel devices, such as a printer to your LifeBook note­book. In order to connect a parallel interface device follow these easy steps: (See Figure 2-6 on page 11 for
location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each end of the connector.
SERIAL PORT
The serial port, or COMM port, allows you to connect serial devices, such as printers or scanners. In order to connect a serial interface device follow these steps: (See
Figure 2-6 on page 11 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each end of the connector.
UNIVERSAL SERIAL BUS (USB) 2.0 PORTS
The two Universal Serial Bus (USB) 2.0 ports allow you to connect USB devices such as game pads, pointing devices, keyboards and speakers. USB 2.0 is downward­compatible with USB 1.1 devices, so older USB devices will work with these ports. USB 2.0 is a much faster design, running forty times faster than USB 1.1. To connect a USB device follow these steps: (See Figure 2-6
on page 11 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
INFRARED PORT
The Infrared IrDA 1.1 (4Mbps) port allows for wireless data transfer between your LifeBook notebook and other IrDA-compatible devices, such as another computer or a printer, without the use of a cable.
(See Figure 2-4 on page 9 for location)
It is important to keep in mind that while carrying out this form of communication, both devices must be placed so their infrared ports are directly facing each other without obstruction. The devices must also be separated by at least 6" but no more than 36" for maximum performance.
51
LifeBook E Series Notebook – Section 4
The following conditions may interfere with infrared communications:
A television, radio remote control unit, or a wireless headphone is being used nearby.
Direct sunlight, fluorescent light, or incandescent light shines directly on the port.
CAUTIONS
Do not move either device while communication is active as it may interrupt data transmission.
Be careful not to scratch the infrared port lens. Scratches, dirt, or other surface marks can degrade operation.
POINT
With Windows 2000 Professional, file transfer is provided through Wireless Link in the Control Panel.
MICROPHONE JACK
The microphone jack allows you to connect an external mono microphone. Your microphone must be equipped with a 1/8"(3.5 mm) mono mini-plug in order to fit into the microphone jack of your LifeBook notebook. In order to connect a microphone follow these easy steps:
(See Figure 2-3 on page 8 for location)
1. Align the connector with the port opening.
2.Push the connector into the port until it is seated.
POINT
If you plug headphones into the headphone jack, you will disable the built-in stereo speakers.
DOCKING PORT
The docking port is used for the connection of your notebook to an optional port replicator or docking station. In order to connect your notebook to one of these devices follow the instructions that came with your port replicator or docking station. (See Figure 2-6 on
page 11 for location)
CAUTION
Some LifeBook notebooks have a sliding panel that encloses the ports. The sliding panel can be damaged if it is left open while the notebook is moved.
EXTERNAL MONITOR PORT
The external monitor port allows you to connect an external monitor. In order to connect an external monitor follow these easy steps: (See Figure 2-6 on page
11 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
3. Tighten the two hold-down screws, located on each end of the connector.
S-VIDEO OUT PORT
The S-Video port allows you to connect and use directly any S-Video device, such as a VCR or television. The S-Video standard provides for a higher quality picture than NTSC or PAL. In order to connect an S-Video device, follow these easy steps: (See Figure 2-6 on page 11
for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
HEADPHONE JACK
The headphone jack allows you to connect headphones, or powered external speakers to your LifeBook note­book. Your device must be equipped with a 1/8" (3.5 mm) stereo mini-plug. In order to connect headphones or speakers follow these easy steps: (See Figure 2-3 on
page 8 for location)
1. Align the connector with the port opening.
2. Push the connector into the port until it is seated.
52
POINT
Pressing the [Fn] + [F10] keys allows you to change your selection of where to send your display video. Each time you press the key combination, you will step to the next choice, starting with the built-in display panel only, moving to the external monitor only, finally moving to both the built-in display panel and an external monitor.
5
Troubleshooting
53
LifeBook E Series Notebook – Section 5
54

Troubleshooting

Your LifeBook notebook is sturdy and subject to few problems in the field. However, you may encounter simple setup or operating problems that you can solve on the spot, or problems with peripheral devices, that you can solve by replacing the device. The information in this section helps you isolate and resolve some of these straightforward problems and identify failures that require service.

IDENTIFYING THE PROBLEM

If you encounter a problem, go through the following procedure before pursuing further troubleshooting:
1. Turn off your LifeBook notebook.
2. Make sure the AC adapter is plugged into your Life­Book notebook and to an active AC power source.
3. Make sure that any card installed in the PC Card slot is seated properly. You can also remove the card from the slot, thus eliminating it as a possible cause of failure.
4. Make sure that any devices connected to the external connectors are plugged in properly. You can also disconnect such devices, thus eliminating them as possible causes of failure.
5. Turn on your LifeBook notebook. Make sure it has been off at least 10 seconds before you turn it on.
6. Go through the boot sequence.
7. If the problem has not been resolved, refer to the Troubleshooting Table, that follows, for more detailed troubleshooting information.
Troubleshooting
n
Conditions under which the problem occurred
n
Any error messages that have occurred
n
Hardware configuration
n
Type of device connected, if any
See the Configuration Label on the bottom of your LifeBook notebook for configuration and serial numbers. (See Figure 2-7 on page 12 for location)
POINT
Do not return a failed LifeBook notebook to Fujitsu PC Corporation until you have received a Return Material Authorization (RMA) number from a support representative.
POINT
If you keep notes about what you have tried, your support representative may be able to help you more quickly by giving additional suggestions over the phone.
8. If you have tried the solutions suggested in the Trou­bleshooting Table without success, contact your support representative:
Toll free: 1-800-8Fujitsu (1-800-838-5487) Fax: 1-901-259-5700 E-mail: 8fujitsu@fujitsupc.com Web site: http://www.fujitsupc.com.
Before you place the call, you should have the following information ready so that the customer support repre­sentative can provide you with the fastest possible solu­tion:
n
Product name
n
Product configuration number
n
Product serial number
n
Purchase date
55
LifeBook E Series Notebook – Section 5
SPECIFIC PROBLEMS
Using the Troubleshooting Table
When you have problems with your LifeBook notebook, try to find the symptoms under the Problem column of the troubleshooting table for the feature giving you difficulty.

TROUB LE SHOOTING TA BL E

You will find a description of common causes for that symptom under the column Possible Cause and what, if anything, you can do to correct the condition under Possible Solutions. All possible causes or solutions may not apply to your LifeBook notebook.
Problem Possible Cause Possible Solutions
Audio Problems
There is no sound coming from the built-in speakers.
The volume is turned too low. Adjust the volume control on your notebook.
The software volume control is set too low.
Headphones are plugged into your notebook.
BIOS audio settings are incorrect.
Problem Page
Audio Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 56
DVD/CD-ROM Drive Problems . . . . . . . . . . . . page 56
Docking Problems . . . . . . . . . . . . . . . . . . . . . . . . page 57
Floppy Disk Drive Problems. . . . . . . . . . . . . . . . page 57
Hard Drive Problems. . . . . . . . . . . . . . . . . . . . . . page 58
Keyboard or Mouse Problems . . . . . . . . . . . . . . page 58
Memory Problems. . . . . . . . . . . . . . . . . . . . . . . . page 58
Modem Problems. . . . . . . . . . . . . . . . . . . . . . . . . page 59
Parallel, Serial and USB Device Problems . . . . . page 59
PC Card Problems . . . . . . . . . . . . . . . . . . . . . . . . page 59
Power Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . page 59
Shutdown and Start-up Problems . . . . . . . . . . . page 61
Video Problems . . . . . . . . . . . . . . . . . . . . . . . . . . page 62
Miscellaneous Problems . . . . . . . . . . . . . . . . . . . page 63
Adjust the sound volume control settings in your software, operating system and applications.
Plugging in headphones disables the built-in speakers, remove the headphones.
Set the BIOS setup utility to the default values within the Multimedia Device Configuration menu. (See
BIOS Setup Utility on page 31 for more information)
Software driver is not config­ured correctly.
DVD/CD-ROM Drive Problems
Notebook fails to recognize DVD/CDs.
DVD/CD is not pushed down onto raised center circle of the drive.
DVD/CD-ROM tray is not latched shut.
Setup utility is set to some­thing other than DVD/CD­ROM or Auto for the Secondary Master Controller.
Wrong drive designator was used for DVD/CD in the application.
Windows DVD/CD Auto Insert Notification function is disabled.
DVD/CD is dirty or defective. Wipe DVD/CD with a non-abrasive CD cleaning
Refer to your application and operating system documentation for help.
Open the DVD/CD-ROM tray and re-install the disk properly.
Push on the front of the DVD/CD-ROM tray until it latches.
Revise BIOS settings for the Secondary Master Controller. (See BIOS Setup Utility on page 31 for
more information)
Verify that the drive designator used by the applica­tion is the same as that used by the operating system. When the operating system is booted from a DVD/ CD, drive designations are automatically adjusted.
Start the DVD/CD from the desktop or application software or re-enable the Windows DVD/CD Auto Insert Notification function. (See Auto Insert Notifi-
cation Function on page 45 for more information)
cloth and reinsert. If it still will not work try another DVD/CD in the drive.
56
Problem Possible Cause Possible Solutions
LifeBook notebook fails to auto-play DVD movie.
DVD Player Software is not installed.
Troubleshooting
Install DVD Player Software using the DVD Appli­cation.
The DVD/CD-ROM Access indicator on the Status Indicator Panel blinks at regular intervals when no disk is in the tray or the DVD drive is not installed.
Docking Problems
Notebook does not turn on when installed in Docking Station.
(15" systems only) When the system is put into or removed from the dock (see details under "possible cause"), the screen resolu­tion changes.
Floppy Disk Drive Problems
Country designator could be set incorrectly.
The Windows DVD/CD Auto Insert Notification function is active and is checking to see if a DVD/CD is ready to run.
LAN Dock AC adapter is not plugged in.
Notebook is not properly seated in the LAN Dock.
When ClickMe! was run when the system was set up for the first time, the system automat­ically assigned SXGA+ resolu­tion to the docking profile that was selected at the time (depending upon whether the system was docked or undocked at the time). Since ClickMe! is only run once, the docking profile for the other configuration (docked or undocked) remains as XGA, and must be changed manually.
Select the DVD player software from the programs list and right-click on the window. Select Properties and verify that the region selected is "USA, Canada."
This is normal. However, you may disable this feature. (See Auto Insert Notification Function on
page 45 for more information)
Provide power to the LAN Docking Station.
Remove and re-dock your notebook and verify that the Docked LED illuminates.
Boot the system in the configuration in which the screen resolution is incorrect (docked or undocked). Right click on the desktop, and select Properties, then click on the Settings tab.
Under Screen Resolution, drag the scroll bar to the right until "1400 x 1050 pixels" is selected. Click [Apply], then click [OK] to accept the changes. Click [OK] again to exit the window.
You cannot access your floppy disk.
You tried to write to a write protected floppy disk.
Floppy disk is not loaded correctly.
BIOS setup utility states
Diskette Controller: Disabled.
The floppy disk drive may not be properly installed.
Security is set to protect access to floppy disk data.
Eject the floppy disk and set it to write enable. (See
External USB Floppy Disk Drive on page 41 for more information)
Eject floppy disk, check orientation and reinsert.
(See External USB Floppy Disk Drive on page 41 for more information)
Revise the setup utility Main menu settings to enable Diskette Controller. (See BIOS Setup Utility
on page 31 for more information)
Remove and reinstall your floppy disk drive. (See Flexible Bay Devices on page 20 for more information)
Verify your password and security settings.
57
LifeBook E Series Notebook – Section 5
Problem Possible Cause Possible Solutions
Hard Drive Problems
You ca n no t a cce ss y our hard drive.
The setup utility is incorrectly set for your internal hard drive.
Set Primary Master correctly in the BIOS. (See BIOS
Setup Utility on page 31 for more information)
Keyboard or Mouse Problems
The built-in keyboard does not seem to work.
You have installed an external keyboard or mouse, and it does not seem to work.
The wrong drive designator was used by an application when a bootable CD-ROM was used to start the notebook.
Security is set so your oper-
Verify drive designator used by application is in use by the operating system. When the operating system is booted from a CD, drive designations are automatically adjusted.
Verify your password and security settings. ating system cannot be started without a password.
The hard disk drive has crashed.
The notebook has gone into
Contact Fujitsu or your local authorized reseller for
a replacement hard disk drive.
Push the Power and Suspend/Resume button. Suspend mode.
Your application has locked out your keyboard.
Try to use your intergrated pointing device to restart
your system. If this fails, turn your LifeBook note-
book off using the power/suspend/resume button,
wait 10 seconds or more, and then turn it back on.
The NumLock key is set. Press the NumLock key to reset it.
Your external device is not properly installed.
Your operating system software is not set up with the
Reinstall your device. (See Device Ports on page 51 for
more information)
Check your device and operating system docu-
mentation and activate the proper driver. correct driver for that device.
Your mouse or keyboard is connected to the wrong PS/2 port on the LAN Dock.
Plug the mouse into the PS/2 Mouse port and the
external keyboard or numeric key pad into the PS/2
Keyboard port. (See Device Ports on page 51 for more
information)
You have connected an external keyboard or a mouse and it seems to be locking up the system.
Memory Problems
Your Power On screen, or Main menu of the BIOS setup utility information, does not show the correct amount of installed memory.
58
Your operating system soft­ware is not setup with the
Check your device and operating system
documentation and activate the proper driver. correct software driver for that device.
Your system has crashed. Try to restart your LifeBook notebook. If that fails,
turn off the power using the power/suspend/resume
button, wait at least 10 seconds, and then power on.
Your memory upgrade module is not properly installed.
Remove and reinstall your memory upgrade
module. (See Memory Upgrade Module on page 49
for more information)
You have a memory failure. Check for Power On Self Test (POST) messages.
(See Power On Self Test Messages on page 64 for more
information)
Problem Possible Cause Possible Solutions
Modem Problems
Messages about modem operation.
Messages about modem operation are generated by whichever modem application is in use.
Parallel, Serial, and USB Device Problems
Troubleshooting
See your application software documentation for additional information.
You have installed a parallel port device, a serial port device or a USB device. Your LifeBook notebook does not recognize the device, or the device does not seem to work properly.
PC Card Problems
A card inserted in the PC Card slot does not work or is locking up the system.
The device is not properly installed.
The device may have been installed while an application was running, so your notebook is not aware of its installation.
Your software may not have correct software driver active.
You may have th e w ro ng I/ O address selected for your device.
Your device and another device are assigned the same I/O address.
Parallel port is set to output only.
The card is not properly installed.
The card may have been installed while an application was running, so your notebook is not aware of its installation.
Remove and reinstall the device. (See Device Ports on
page 51 for more information)
Close the application and restart your LifeBook notebook.
See your software documentation and activate the correct driver.
See your device documentation and software docu­mentation to determine the required I/O address. Change the settings in the BIOS setup utility. (See
BIOS Setup Utility on page 31 for more information)
Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.
Check parallel port setting in the BIOS and set to bi-directional or ECP.
Remove and reinstall the card. (See PC Cards on
page 47 for more information)
Close the application and restart your LifeBook notebook.
Power Failures
You turn on your LifeBook notebook and nothing seems to happen.
Your software may not have the correct driver active.
You may have th e w ro ng I/O address selected for your PC Card device.
You r PC Ca rd de vi ce an d another device are assigned the same I/O address.
The installed primary battery is completely discharged, there is no optional second battery installed or there is no Power adapter (AC or Auto/Airline) installed.
See your software documentation and activate the correct driver.
See your PC Card documentation to determine the required I/O address. Change the settings in the BIOS. (See BIOS Setup Utility on page 31 for
more information)
Check all I/O addresses located within the BIOS setup utility and any other installed hardware or software to make sure there are no duplications.
Check the Status Indicator Panel to determine the presence and condition of the batteries. (See Status Indicator Panel on page 13 for more information) Install a charged battery or a Power adapter.
59
LifeBook E Series Notebook – Section 5
Problem Possible Cause Possible Solutions
You turn on your LifeBook notebook and nothing
The primary battery is installed but is faulty.
seems to happen.
(continued)
The battery or batteries are low. Check the Status Indicator Panel to determine the
The AC or auto/airline adapter is not plugged in properly.
Use the Status Indicator panel to verify the presence and condition of the batteries. (See Status Indicator Panel on page 13 for more information) If a battery is indicating a short, remove that battery and operate from another power source or replace that battery.
presence and condition of the batteries. (See Status Indicator Panel on page 13 for more information) Use a Power adapter to operate until a battery is charged or install a charged battery.
Verify that your adapter is connected correctly. (See
Power Sources on page 29 for more information)
Your LifeBook notebook turns off all by itself.
The Power adapter (AC or auto/airline) has no power from the AC outlet, airplane seat jack, or the car’s cigarette lighter.
The Power adapter (AC or auto/airline) is faulty.
The power management parameters are set for auto timeouts which are too short for your operating needs.
Move the AC cord to a different outlet, check for a line switch or tripped circuit breaker for the AC outlet. If you are using an auto/airline adapter in a car make sure the ignition switch is in the On or Accessories position.
Try a different Power adapter or install a charged optional second battery.
Press any button or key on the keyboard, or move the mouse. If that fails, push the Power/Suspend/ Resume button. Check your power management settings, or close your applications and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs.
You are operating on battery power only and have ignored a low battery alarm until the
Install a power adapter and then push the Power and Suspend/Resume button. (See Power Sources on
page 29 for more information)
batteries are all at the dead battery state and your machine has gone into Dead Battery Suspend mode.
You have a battery failure. Verify the condition of the batteries using the
Status Indicator panel, and replace or remove any batteries that are shorted. (See Status Indicator
Panel on page 13 for more information)
Your LifeBook notebook will not work on battery alone.
60
Your power adapter has failed or lost its power source.
The installed batteries are dead.
Make sure the adapter is plugged in and the outlet has power.
Replace the battery with a charged one or install a Power adapter.
No batteries are installed. Install a charged battery.
The batteries are improperly installed.
Your installed batteries are faulty.
Verify that the batteries are properly connected by re-installing them.
Verify the condition of the batteries using the Status Indicator panel and replace or remove any batteries that are shorted. (See Status Indicator
Panel on page 13 for more information)
Problem Possible Cause Possible Solutions
The batteries seem to discharge too quickly.
You are running an application that uses a great deal of power due to frequent hard drive or DVD/CD-ROM access, or use of a modem or LAN PC card.
Troubleshooting
Use both the primary battery and an optional second battery and/or use a power adapter for this application when at all possible.
The power savings features may be disabled.
The brightness is turned all the way up.
The batteries are very old. Replace the batteries.
The batteries have been exposed to high temperatures.
The batteries are too hot or too cold.
Shutdown and Startup Problems
The Power and Suspend/ Resume button does not work.
The Power and Suspend/ Resume button is disabled from the Power -> Advanced submenu of the setup utility.
You did not hold the button in long enough.
There may be a conflict with the application software.
Check the power management and/or setup utility settings in the Power Savings menu and adjust according to your operating needs.
Turn down the brightness adjustment. The higher the brightness the more power your display uses.
Replace the batteries.
Restore the LifeBook notebook to normal operating temperature. The Charging icon on the Status Indi­cator panel will flash when the battery is outside its operating range.
Enable the button from the setup utility.
Hold the button longer. This may need to be a few seconds if your application is preventing the CPU from checking for button pushes.
Close all applications and try the button again.
The system powers up, and displays power on informa­tion, but fails to load the operating system.
Your system display won’t turn on when the system is turned on or when the system has resumed.
An error message is displayed on the screen during the notebook (boot) sequence.
The boot sequence settings of the setup utility are not compatible with your configuration.
You have a secured system requiring a password to load your operating system.
Internal hard drive was not detected.
The system may be password­protected.
Power On Self Test (POST) has detected a problem.
Set the operating source by pressing the [ESC] key while the Fujitsu logo is on screen or use the [F2] key and enter the setup utility and adjust the source settings from the Boot menu. (See BIOS Setup
Utility on page 31 for more information)
Make sure you have the right password. Enter the setup utility and verify the Security settings and modify them accordingly. (See BIOS Setup Utility on
page 31 for more information)
Use the BIOS setup utility or Primary Master submenu, located within the Main menu, to try to auto detect the internal hard drive.
Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.
See the POST messages to determine the meaning and severity of the problem. Not all messages are errors; some are status indicators. (See Power On Self
Test Messages on page 64 for more information)
61
LifeBook E Series Notebook – Section 5
Problem Possible Cause Possible Solutions
Your LifeBook notebook appears to change setup parameters when you start it.
BIOS setup changes were not saved when you exited the BIOS setup utility, returning it to previous settings.
The BIOS CMOS hold-up battery has failed.
Video Problems
Make sure you select Save Changes And Exit when exiting the BIOS setup utility.
Contact your support representative for repairs. This is not a user serviceable part but has a normal life of 3 to 5 years.
The built-in display is blank when you turn on your LifeBook notebook.
The LifeBook notebook turned on with a series of beeps and your built-in display is blank.
Your system display won’t turn on when the system is turned on or when the system has resumed.
Something is pushing on the Closed Cover switch.
The display angle and bright­ness settings are not adequate for your lighting conditions.
The LifeBook notebook is set for an external monitor only.
The power management time­outs may be set for very short intervals and you failed to notice the display come on and go off again.
Power On Self Test (POST) has detected a failure which does not allow the display to operate.
The system may be password­protected.
Clear the Closed Cover switch. (See Figure 2-3 on
page 8 for location)
Move the display and the brightness control until you have adequate visibility.
Pressing [F10] while holding down the [Fn] key allows you to change your selection of where to send your display video. Each time you press the combination of keys you will step to the next choice. The choices, in order are: built-in display only, external monitor only, both built-in display and external monitor.
Press any button or key on the keyboard, or move the mouse to restore operation. If that fails, push the Power and Suspend/Resume button. (The display may be shut off by Standy mode, Auto Suspend or Video Timeout.)
Contact your support representative.
Check the status indicator panel to verify that the Security icon is blinking. If it is blinking, enter your password.
The display goes blank by itself after you have been using it.
62
The notebook has gone into Video timeout, Standby mode, Suspend mode or Save-to-Disk mode because you have not used it for a period of time.
Something is pushing on the Closed Cover switch.
The power management time­outs may be set for very short intervals and you failed to notice the display come on and go off again.
Press any button or key on the keyboard, or move the mouse to restore operation. If that fails, push the Power and Suspend/Resume button. Check your power management settings, or close your applica­tions and go to the Power Savings menu of the setup utility to adjust the timeout values to better suit your operation needs. (See BIOS Setup Utility on
page 31 for more information)
Check the Closed Cover switch. (See Figure 2-3 on page 8 for location)
Press any button or key on the keyboard, or move the mouse to restore operation. If that fails, push the Power and Suspend/Resume button. (The display may be shut off by Standby Mode, Auto Suspend or Video Timeout.)
Problem Possible Cause Possible Solutions
The Built-in Display does not close.
A foreign object, such as a paper clip, is stuck between the display and the keyboard.
Troubleshooting
Remove all foreign objects from the keyboard.
The Built-in Display has bright or dark spots.
You have connected an external monitor and it does not come on.
The application display uses only a portion of your screen and is surrounded by a dark frame.
You have connected an external monitor and it does not display any information.
If the spots are very tiny and few in number, this is normal for a large LCD display.
If the spots are numerous or large enough to interfere with your operation needs.
Your external monitor is not compatible with your LifeBook notebook.
You are running an application that does not support 800 x 600 pixel resolution display and display compression is enabled.
Your BIOS setup is not set to enable your external monitor.
Your external monitor is not properly installed.
Your operating system soft­ware is not setup with the correct software driver for that device.
This is normal; do nothing.
Display is faulty; contact your support representative.
See your monitor documentation and the External Monitor Support portions of the Specifications section on page 77.
Display compression gives a clearer but smaller display for applications that do not support 800 x 600 pixel resolution. You can fill the screen but have less resolution by changing your display compres­sion setting, (See the Video Features submenu, located within the Advanced menu of the BIOS.)
(See BIOS Setup Utility on page 31 for more informa­tion)
Try toggling the video destination by pressing [Fn] and [F10] together, or check your BIOS setup and enable your external monitor. (See the Video Features submenu, located within the Advanced Menu of the BIOS.) (See BIOS Setup Utility on page 31 for more
information)
Reinstall your device. (See External Monitor Port on page 52 for more information)
Check your device and operating system documentation and activate the proper driver.
Miscellaneous Problems
An error message is displayed on the screen during the operation of an application.
Application software often has its own set of error message displays.
See your application manual and help displays screens for more information. Not all messages are errors some may simply be status.
63
LifeBook E Series Notebook – Section 5
POWER ON SELF TEST MESSAGES
The following is an alphabetic list of error-and-status messages that Phoenix BIOS and/or your operating system can generate and an explanation of each message. Error messages are marked with an *. The most common errors are marked with a #. If an error message is displayed that is not in this list, write it down and check your operating system documentation both on screen and in the manual. If you can find no reference to the message and its meaning is not clear, contact your support representative for assistance.
nnnn Cache SRAM Passed
Where nnnn is the amount of system cache in kilobytes successfully tested by the Power On Self Test. (This can only appear if you have an SRAM PC Card installed.)
*Diskette drive A error or Diskette drive B error
Drive A: or B: is present but fails the BIOS Power On Self Test diskette tests. Check to see that the drive is defined with the proper diskette type in the Setup Utility, (See BIOS Setup Utility on page 31 for more information) and that the diskette drive is installed correctly. If the disk drive is properly defined and installed, avoid using it and contact your support representative.
*Extended RAM Failed at offset: nnnn
Extended memory not working or not configured prop­erly. If you have an installed memory upgrade module, verify that the module is properly installed. If it is properly installed, you may want to check your Windows Setup to be sure it is not using unavailable memory until you can contact your support representa­tive.
nnnn Extended RAM Passed
Where nnnn is the amount of memory in kilobytes successfully tested.
*Failing Bits: nnnn The hex number nnnn
This is a map of the bits at the memory address (in System, Extended, or Shadow memory) which failed the memory test. Each 1 (one) in the map indicates a failed bit. This is a serious fault that may cause you to lose data if you continue. Contact your support representative.
*Fixed Disk x Failure or Fixed Disk Controller Failure (where x = 1-4)
The fixed disk is not working or not configured properly. This may mean that the hard drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to check for the hard drive type settings and correct them if necessary. If the settings are OK and the message appears when you restart the system, there may be a serious fault which might cause you to lose data if you continue. Contact your support representative.
*Incorrect Drive A type – run SETUP
Type of floppy drive A: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
*Incorrect Drive B type – run SETUP
Type of floppy drive B: not correctly identified in Setup. This means that the floppy disk drive type identified in your setup utility does not agree with the type detected by the Power On Self Test. Run the setup utility to correct the inconsistency.
*Invalid NVRAM media type
Problem with NVRAM access. In the unlikely case that you see this message you may have some display prob­lems. You can continue operating but should contact your support representative for more information.
*Keyboard controller error
The keyboard controller test failed. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.
*Keyboard error
Keyboard not working. You may have to replace your keyboard or keyboard controller but may be able to use an external keyboard until then. Contact your support representative.
*Keyboard error nn
BIOS discovered a stuck key and displays the scan code for the stuck key. You may have to replace your keyboard but may be able to use an external keyboard until then. Contact your support representative.
*Monitor type does not match CMOS – Run SETUP
Monitor type not correctly identified in Setup. This error probably means your BIOS is corrupted, run the setup utility and set all settings to the default conditions. If you still get this error, contact your support representative.
#*Operating system not found
Operating system cannot be located on either drive A: or drive C:. Enter the setup utility and see if both the fixed disk, and drive A: are properly identified and that the boot sequence is set correctly. Unless you have changed your installation greatly, the operating system should be on drive C:. If the setup utility is correctly set, your hard drive may be corrupted and your system may have to be reinstalled from your back up media.
64
Troubleshooting
*Parity Check 1 nnnn
Parity error found in the system bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data-destroying failure. Contact your support representative.
*Parity Check 2 nnnn
Parity error found in the I/O bus. BIOS attempts to locate the address and display it on the screen. If it cannot locate the address, it displays ????. This is a potentially data destroying failure. Contact your support representative.
#*Press <F1> to resume, <F2> to SETUP
Displayed after any recoverable error message. Press the [F1] key to continue the boot process or the [F2] key to enter Setup and change any settings.
#*Previous boot incomplete – Default configuration used
Previous Power On Self Test did not complete success­fully. The Power On Self Test will load default values and offer to run Setup. If the previous failure was caused by incorrect values and they are not corrected, the next boot will likely fail also. If using the default settings does not allow you to complete a successful boot sequence, you should turn off the power with the power/suspend/ resume button and contact your support representative.
*Real time clock error
Real-time clock fails BIOS test. May require board repair. Contact your support representative.
*Shadow RAM Failed at offset: nnnn
Shadow RAM failed at offset nnnn of the 64k block at which the error was detected. You are risking data corrup­tion if you continue. Contact your support representative.
nnnn Shadow RAM Passed
Where nnnn is the amount of shadow RAM in kilobytes successfully tested.
*System battery is dead – Replace and run SETUP
The BIOS CMOS RAM memory hold up battery is dead. This is part of your BIOS and is a board mounted battery which requires a support representative to change. You can continue operating but you will have to use setup utility default values or reconfigure your setup utility every time you turn off your LifeBook notebook. This battery has an expected life of 2 to 3 years.
System BIOS shadowed
System BIOS copied to shadow RAM.
*System CMOS checksum bad – run SETUP
BIOS CMOS RAM has been corrupted or modified incorrectly, perhaps by an application program that
changes data stored in BIOS memory. Run Setup and reconfigure the system.
*System RAM Failed at offset: nnnn
System memory failed at offset nnnn of in the 64k block at which the error was detected. This means that there is a fault in your built-in memory. If you continue to operate, you risk corrupting your data. Contact your support representative for repairs.
nnnn System RAM Passed
Where nnnn is the amount of system memory in kilo­bytes successfully tested.
*System timer error
The timer test failed. The main clock that operates the computer is faulty. Requires repair of system board. Contact your support representative for repairs.
UMB upper limit segment address: nnnn
Displays the address of the upper limit of Upper Memory Blocks, indicating released segments of the BIOS memory which may be reclaimed by a virtual memory manager.
Video BIOS shadowed
Video BIOS successfully copied to shadow RAM.
MODEM RESULT CODES
The operating system and application software that is factory installed detects the modem characteristics and provides the necessary command strings to operate the modem. The internal modem operation is controlled by generic AT commands from the operating system and application software. The standard long form result codes may, in some cases, be displayed on your screen to keep you informed of the actions of your modem. The operating system and application software may suppress display of the result codes.
Examples of result codes are:
n
OK
n
NO CARRIER
n
NO DIALTONE
n
CONNECT 53000 (Connection complete at 53,000 bps.)
n
ERROR
n
FAX
n
RING (This means an incoming call.)
n
BUSY
n
NO ANSWER
When using the internal modem with applications that are not factory installed refer to the application documentation.
65
LifeBook E Series Notebook – Section 5

RESTORING YOUR PRE-INSTALLED SOFTWARE

The Drivers and Applications CD contains:
Sets of device drivers and Fujitsu utilities (in specific directories) that are unique to your LifeBook note­book configuration for use as documented below.
A link to the Drive Image Special Edition (DISE) utility on your hard disk drive.
Read-me files that provide additional use information for items on this CD-ROM.
CAUTION
If the DAR CD is in the drive when you boot up the system, a message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration. If you wish to install drivers or applications only from the CD, remove the disk from the drive, reboot the system, and insert the CD after Windows has started.
POINT
If you have access to the internet, visit the Fujitsu Support web site at www.fujitsupc.com to check for the most current information, drivers and hints on how to perform recovery and system updates.
DRIVE IMAGE SPECIAL EDITION (DISE)
PowerQuest Drive Image Special Edition (DISE) provides a way to restore your computer if you experi­ence a hard disk crash or other sy stem failure. Fu jitsu has used DISE to create an image of everything installed on the computer at the time you purchased it. The image is saved on a separate partition on the hard disk. You can use DISE to restore the factory image and return your computer to the state in which it was shipped from Fujitsu.
Although it is not necessary, you can use DISE to store additional image files that you create. For example, if you install several applications and save data files on your hard disk, you can create a new image file that includes them and then save that image file on the hard disk. Then, in the event of a hard disk failure, you can restore the image that includes the applications and data
files you use.
POINT
Using the DISE feature will reduce the amount of usable disk space on your hard disk drive.
partition, and it must be directly before the backup partition on your hard disk.
There are two ways to implement the DISE utility: When booting up the system, or from the desktop.
Creating a backup image when booting up
Before creating a backup image at boot-up, you must first change the boot-up priority in the BIOS so that the system will go to the CD drive first, rather than trying to boot-up from the hard drive or an external floppy disk drive.
To change the boot-up priority:
1. Start your system and press the [F2] key when the Fujitsu logo appears. You will enter the BIOS Setup Utility.
2. Using the arrow keys, go to the Boot menu.
3. Arrow down to the Boot Device Priority submenu and press [Enter].
4. Arrow down to the CD-ROM drive in the list, and press the space bar (or the + key) to move the CD­ROM drive to the top of the list. (The system attempts to boot from the devices in the order in which they are listed.)
5. Press [F10], then click on [Yes] to exit the BIOS Setup Utility and return to the boot process.
After you have changed the boot priority, you can create a backup image when you are booting up:
1. Install the DAR CD in the drive prior to booting up. When bootup begins, a message will appear informing you that continuing to boot from the CD will overwrite all information on the hard drive, including saved files, and restore the hard drive to its factory configuration.
2. When you are asked if you want to restore the factory image, click [Y]es.
Creating a backup image from the desktop
To create a backup image from the desktop, select Drive Image SE from the Program list. You will initially be prompted to create a backup diskette. It is not necessary to create the backup diskette, since the DAR CD performs the same function.
1. At the Drive Image Special Edition main screen, click Options> Create New Backup. DISE displays a warning that it must go to DOS to create the image.
3. Click Ye s .
DISE creates an image file in the backup partition. If you created a backup image previously, the new image overwrites the old one.
Creating a Backup Image
You can create a backup image of your C:\ drive at any time. The C:\ partition must be a FAT, FAT32, or NTFS
66
Enlarging the Backup Partition
If there is not enough unused space in the backup parti­tion on your hard disk, DISE will resize the partition. DISE will display the minimum, maximum, and recom-
mended sizes for the backup partition. You choose the size you want.
DISE takes the space from the FAT, FAT32, or NTFS partition that you are backing up. If there is not enough unused space in that partition to take, you will not be able to resize the backup partition and create an image file. You can delete files from the FAT, FAT32, or NTFS partition to create more unused space on the hard disk.
Restoring a Backup Image
You can restore either a factory image or a backup image you created. Be aware that restoring a backup image will replace the contents of the C:\ partition with the image you restore.
1. Disable virus protection software. If virus protection software is enabled, DISE will hang.
2. From the DISE main window, click Options > Restore Backup to restore an image you created, or click Options > Restore Factory Backup to restore the factory image.
DISE shuts down to DOS and restores the image file.
Re-Installing Individual Drivers and Applications
The Drivers and Application CD can be used to selec­tively re-install drivers and/or applications that may have been un-installed or corrupted.
To re-install drivers and/or applications:
1. Boot up the system and insert the DAR CD after Windows has started. The LifeBook Easy Installation screen appears.
2. Select the drivers and applications you want to install from the list that is displayed.
3. Click [Start]. Follow the prompts that appear to complete installation of the selected drivers and/or applications.
Troubleshooting
67
LifeBook E Series Notebook – Section 5
68
6
Care and Maintenance
69
LifeBook E Series Notebook – Section 6
70

Care and Maintenance

Care and Maintenance
If you use your LifeBook notebook carefully, you will increase its life and reliability. This section provides some tips for looking after the notebook and its devices.
WARNING
Electrical equipment may be hazardous if misused. Oper­ations of this product or similar products, must always be supervised by an adult. Do not allow children access to the interior of any electrical products and do not permit them to handle any cables.
LIFEBOOK NOTEBOOK
Caring for your Notebook
Your LifeBook notebook is a durable but sensitive electronic device. Treat it with respect and care.
Make a habit of transporting it in a suitable carrying case.
Do not attempt to service the computer yourself. Always follow installation instructions closely.
Keep it away from food and beverages.
If you accidentally spill liquid on your notebook:
1. Turn it off.
2. Position it so that the liquid can run out.
3. Let it dry out for 24 hours, or longer if needed.
4. If your notebook will not boot after it has dried out, call your support representative.
Do not use your LifeBook notebook in a wet environ­ment (near a bathtub, swimming pool).
Always use the AC adapter and batteries that are approved for your LifeBook notebook.
Avoid exposure to sand, dust and other environmental hazards.
Do not expose your LifeBook notebook to direct sun­light for long periods of time as temperatures above 140° F (60° C) may damage your notebook.
• Keep the covers closed on the connectors and slots when they are not in use.
Do not put heavy or sharp objects on the computer.
If you are carrying your LifeBook notebook in a brief­case, or any other carrying case, make sure that there are no objects in the case pressing on the lid.
Do not drop your LifeBook notebook.
Do not touch the screen with any sharp objects.
Cleaning your LifeBook notebook
Always disconnect the power plug. (Pull the plug, not the cord.)
Clean your LifeBook notebook with a damp, lint-free cloth. Do not use abrasives or solvents.
Use a soft cloth to remove dust from the screen. Never use glass cleaners.
Storing your LifeBook notebook
If storing your LifeBook notebook for a month or longer, turn your LifeBook off and remove all Lithium ion batteries.
Store your LifeBook notebook and batteries sepa­rately. If you store your notebook with a battery installed, the battery will discharge, and battery life will be reduced. In addition, a faulty battery might damage your notebook.
Store your notebook in a cool, dry location. Temperatures should remain between 5ºF (-15ºC) and 140ºF (60ºC).
Traveling with your LifeBook notebook
Do not transport your LifeBook notebook while it is turned on.
Do not check your LifeBook notebook as baggage. Carry it with you.
Always bring your System Recovery CD (Windows 2000 systems only) that came with your notebook when you travel. If you experience system software problems while traveling, you may need it to correct any problems.
When traveling with the hard drive removed, wrap the drive in a non-conducting materials (cloth or paper). If you have the drive checked by hand, be ready to install the drive if needed. Never put your hard drive through a metal detector. Have your hard drive hand­inspected by security personnel. You can however, put your hard drive through a properly tuned X-ray machine.
Take the necessary plug adapters if you're traveling overseas. Check the following diagram to determine which plug adapter you'll need or ask your travel agent.
71
LifeBook E Series Notebook – Section 6
Outlet Type Location
United States, Canada,
Mexico, parts of Latin America, Japan, Korea, the Philippines, Taiwan
Russia and the Commonwealth
of Independent States (CIS),
most of Europe, parts of Latin
America, the Middle East, parts
of Africa, Hong Kong, India,
most of South Asia
United Kingdom, Ireland,
Malaysia, Singapore,
parts of Africa
China, Australia,
New Zealand
BATTERIES
Caring for your Batteries
Always handle batteries carefully.
Do not short-circuit the battery terminals (that is, do not touch both terminals with a metal object). Do not carry lose batteries in a pocket or purse where they may mix with coins, keys, or other metal objects. Doing so may cause an explosion or fire.
Do not drop, puncture, disassemble, mutilate or incinerate the battery.
Recharge batteries only as described in this manual and only in ventilated areas.
Do not leave batteries in hot locations for more than a day or two. Intense heat can shorten battery life.
Do not leave a battery in storage for longer than 6 months without recharging it.
Increasing Battery Life
Power your LifeBook notebook through the AC or optional auto/airline adapter whenever possible.
If your LifeBook notebook is running on battery power all day, connect it to the AC adapter overnight to recharge the battery.
Keep brightness to the lowest level comfortable.
Set the power management for maximum battery life.
Put your LifeBook notebook in Suspend mode when it is turned on and you are not actually using it.
Limit your DVD/CD-RW/CD-ROM access.
Disable the Windows CD Auto Insert function.
Always use fully charged batteries.
Eject PCMCIA cards when not in use.
FLOPPY DISKS AND DRIVES
Caring for your Floppy Disks
Avoid using the floppy disks in damp and dusty locations.
Never store a floppy disk near a magnet or magnetic field.
Do not use a pencil or an eraser on a disk or disk label.
Avoid storing the floppy disks in extremely hot or cold locations, or in locations subject to severe temperature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).
Do not touch the exposed part of the disk behind the metal shutter.
Caring for your Floppy Disk Drive
To clean, wipe the floppy disk drive clean with a dry soft cloth, or with a soft cloth dampened with water or a solution of neutral detergent. Never use benzene, paint thinner or other volatile material.
Avoid storing the floppy disk drive in extremely hot or cold locations, or in locations subject to severe tem­perature changes. Store at temperatures between 50º F (10ºC) and 125ºF (52ºC).
Keep the floppy disk drive out of direct sunlight and away from heating equipment.
Avoid storing the floppy disk drive in locations subject to shock and vibration.
Never use the floppy disk drive with any liquid, metal, or other foreign matter inside the floppy disk drive or disk.
Never disassemble or dismantle your floppy disk drive.
DVDs AND CDs
Caring for your DVDs and CDs
DVDs and CDs are precision devices and will function reliably if given reasonable care.
Always store your DVD/CDs in its case when it is not in use.
Always handle DVD/CDs by the edges and avoid touching the surface.
Avoid storing any DVD/CDs in extreme temperatures.
Do not bend DVD/CDs or set heavy objects on them.
Do not spill liquids on DVD/CDs.
Do not scratch DVD/CDs.
72
Do not put a label on DVD/CDs.
Do not get dust on DVD/CDs.
Never write on the label surface with a ballpoint pen or pencil. Always use a felt pen.
If a DVD/CD is subjected to a sudden change in tem­perature, cold to warm, condensation may form on the surface. Wipe the moisture off with a clean, soft, lint free cloth and let it dry at room temperature. DO NOT use a hair dryer or heater to dry DVD/CDs.
If a DVD/CD is dirty, use only a DVD/CD cleaner or wipe it with a clean, soft, lint free cloth starting from the inner edge and wiping to the outer edge.
Caring for your Media Drive
Your media drive is durable but you must treat it with care. Please pay attention to the following points:
The drive rotates the compact disk at a very high speed. Do not carry it around or subject it to shock or vibration with the power on.
Avoid using or storing the drive where it will be exposed to extreme temperatures.
Avoid using or storing the drive where it is damp or dusty.
Avoid using or storing the drive near magnets or devices that generate strong magnetic fields.
Avoid using or storing the drive where it will be subjected to shock or vibration.
Do not disassemble or dismantle the DVD drive or CD-RW drive.
Care and Maintenance
PC CARDS
Caring for your PC Cards
PC Cards are durable, but you must treat them with care. The documentation supplied with your PC Card will provide specific information, but you should pay attention to the following points:
To keep out dust and dirt, store PC Cards in their protective sleeves when they are not installed in your LifeBook notebook.
Avoid prolonged exposure to direct sunlight or excessive heat.
Keep the cards dry.
Do not flex or bend the cards, and do not place heavy objects on top of them.
Do not force cards into the slot.
Avoid dropping cards, or subjecting them to excessive vibration.
73
LifeBook E Series Notebook – Section 6
74
7
Specifications
75
LifeBook E Series Notebook – Section 7
76
Specifications
Specifications
This section provides the general hardware and environ­mental specifications for your LifeBook notebook. Specific details about your system may vary from those referenced here. For an updated list of current configu-
rations, please go to the Fujitsu PC Web site at: www.fujitsupc.com.
POINT
All options listed are accurate as of the date of print; sub­stitutions may have been made subsequent to date of publication.
CONFIGURATION LABEL
Your LifeBook notebook contains a configuration label located on the bottom of the system (See Figure 2-7 on page 12 for location). This label contains specific infor­mation regarding the options you’ve chosen for your notebook. Following is an example label, and informa­tion about its various parts.
Operating System
Configuration ID
Memory
Hard Drive Size
Devices
FPC ID
Configuration P/N: AMExxxxxxxxxxxxxx FPC P/N: FPCM70xxx
E4010, PM 1.4G, 14T, XPP, 30G, 256M, DVD, WLAN
Model
Speed
Processor Screen
Size
Figure 7-1 Configuration Label
MICROPROCESSOR
Intel® Pentium M Processor
Up to 1.6GHz, depending upon the configuration of your LifeBook (Refer to the configuration label on your system to determine processor speed.)
CHIPSET
Intel 855GM, 400MHz bus speed
MEMORY
System Memory Range: Upgradeable to 1GB, DDR266 (512MB x 2) 2 DIMM slots
Cache Memory
1MB on-die L2
BIOS Memory
1MB Flash ROM
VIDEO
Built-in color flat-panel TFT active matrix LCD display with simultaneous display capability.
Video Color and Resolution
Internal:
14.1" XGA: 1024 x 768 pixel resolution, 16M colors 15" SXGA+: 1400 x 1050 pixel resolution, 16M colors
External: 1600 x 1200 pixel resolution, 64K colors at 60Hz Simultaneous Video (XGA, SVGA, VGA compatible):
14.1": 1024 x 768, 16M colors max 15": 1400 x 1050, 16M colors max
Graphics Accelerator Card
Intel 855GM, with up to 64MB UMA with DVMT. 4x AGP supported
AUDIO
AC97 Codec Sigmatel 9767
Stereo headphone jack, 1 V impedance 32 Ohms
Mono microphone jack, 100mV impedance 10K Ohms
Two built-in stereo speakers, elliptical (~15 x 35 mm
or less, minimum
rms
or less, minimum
rms
diameter)
MASS STORAGE DEVICE OPTIONS
Floppy Disk Drive
Optional External USB Floppy Disk Drive
Hard Disk Drive
30GB, 40GB, or 60GB Ultra DMA 100
Media Drive
Modular CD, or,
Modular DVD drive, or,
Modular DVD/CD-RW combo drive
FEATURES
Integrated Pointing Device: To u c h p a d
LifeBook Security/Application Panel
Security Panel: 4-button security combination for both hardware and software.
One Touch Panel: 4-button application launcher for Internet, e-mail and software while your LifeBook note­book is On state. Your LifeBook Application Panel buttons are assigned the following defaults:
Button Label Button Function Default Application
1 Application A Notepad
2 Application B Calculator
3 Internet Internet Explorer
4 E-Mail Netscape Messenger/
Outlook Express
Table 7-1. Application Launcher Buttons
77
LifeBook E Series Notebook – Section 7
Theft Prevention Lock Slot
Lock slot for use with physical restraining security systems. The locking system by Kensington is recommended.
Communications
Integrated 10/100 base-Tx Ethernet LAN Internal V.90 standard 56K* fax/modem (ITU V.90, 56K data, 14.4K fax).
Integrated Wireless LAN (802.11b)** with Antenna On/ Off switch. (Standard feature on Centrino model; optional on Pentium M model)
* Actual data transfer rate over U.S. telephone lines varies
and is less than 56Kbps due to the current FCC regula­tions and line conditions.
** Operates at 2.4GHz; communications range may vary,
depending upon surrounding environment.
DEVICE PORTS
Combination PC Card slot for one Type III/two Type II cards: PCMCIA Standard 2.1 with CardBus support
Embedded Smart Card Reader (requires optional Smart Card holder and third-party software)
One 25-pin D-SUB two-way Centronics type connector for parallel input/output devices; Bi-directional, output only or ECP
One 120-pin connector for docking devices.
One 15-pin D-SUB connector for VGA external monitor (see Display specifications)
One 9-pin D-SUB connector for RS-232C serial input/output devices
One S-Video Out port
Two connectors for USB 2.0 (Universal Serial Bus) input/output devices
Fast IR (up to 4 Mbps) compatible infrared port for wireless data transfer
One stereo headphone jack (See Audio specifications)
One mono microphone jack (See Audio specifications)
One modular modem (RJ-11) connector
One modular LAN (RJ-45) connector
KEYBOARD
Built-in keyboard with all functions of 87 key keyboards.
Total number of keys: 87
Function keys: 12, [F1] through [F12]
Feature extension key: [Fn]
Windows keys: 3, two Start keys and an application key
Key pitch: 19 mm
Key stroke: 2.7 mm
Built-in Touchpad pointing device with left and right buttons
External Keyboard Support
USB-compatible
PS/2-compatible (with optional docking station)
External Numeric Keypad Support
USB-compatible
PS/2-compatible (with optional docking station)
External Mouse Support
USB-compatible
PS/2-compatible (with optional docking station)
Management Standard
DMI 2.0-ready, WFM 2.0-compliant
POWER
Batteries
Main 8-cell Lithium ion battery, rechargeable, 14.4V, 3800 mAh
Option: Second 6-cell Lithium ion battery, rechargeable,
10.8V, 3400 mAh (for Flexible Bay installation)
Adapters
AC Adapter: Autosensing 100-240V AC, 80W, supplying 19V DC, 4.22A, to the LifeBook notebook, Fujitsu Model FPCAC33AP, which includes an AC cable.
Option: Auto/Airline Adapter: Converts the DC voltage from an automobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your notebook.
Power Management
Conforms to ACPI (Advanced Configuration & Power Interface)
Electrostatic Discharge (ESD)
9 kV
DIMENSIONS
Overall Dimensions
12.82" x 10.73" x 1.44" (325.5 mm x 272.5 mm x 36.5 mm)
ENVIRONMENTAL REQUIREMENTS
Te mp e r at u r e
Operating: 5° to 35° C (41° to 95° F) Non-operating: –15° to 60° C (5° to 140° F)
Humidi ty
Operating: 20% to 85%, relative, non-condensing. Non-operating; 8% to 85%, relative, non-condensing
Altitude
Operating: 10,000 feet (3,048 m) maximum
78
POPULAR ACCESSORIES
For ordering or additional information on Fujitsu accessories please visit our Web site at: www.fujitsupc.com or call 1-800-733-0884.
Memory Upgrades
PC2100 DDR266 Memory Modules:
256MB
512MB
Docking
Port Replicator
Expansions
External USB floppy disk drive
Power
Additional main Lithium ion battery
Specifications
Modular Lithium ion battery
Auto/Airline Adapter
Additional AC Adapter
Additional Accessories
Numeric Keypad
Presentation Audio System
MindPath PocketPoint
TeleAdapt 16' TeleCord
Notebook Guardian Lock
IBM Modem Saver
Monitor Stand
Carrying Cases
Diplomat
ProPack Backpack
Executive Plus
79
LifeBook E Series Notebook – Section 7
PRE-INSTALLED SOFTWARE
Software Application (Vendor) Windows 2000
Adobe Acrobat Reader X X X Fujitsu HotKey Utility X X Fujitsu BatteryAid/HotKey Utility X PowerQuest Drive Image Special Edition X X X LifeBook Application Panel Software X X X Security Application Panel Software X X X McAfee.com VirusScan Online X X X Earthlink XX Netscape 7.0 X X X Quicken 2003 New User Edition X X Intel SpeedStep X Microsoft Works X X
Windows XP
Home
Windows XP Pro
Your Fujitsu LifeBook notebook comes with pre­installed software for playing audio and video files of various formats. The software configuration installed is dependent upon the operating system that is pre­installed on your system. (Refer to Table 7-2.) In addi­tion, there is file transfer software, virus protection soft­ware and Power Management software.
Software vendors occasionally update their software packages. To ensure that you are using the optimal version for your LifeBook in the future, visit the software company web sites periodically.
Manuals
Included with your LifeBook notebook you will find manuals for your operating system and other pre­installed software. Manuals that are not included are available online through the help system of the software. We recommend that you review these manuals for general information on the use of these applications.
Tutorials
All operating systems and most application software have tutorials built-into them upon installation. We highly recommend that you step through the tutorial before you use an application.
80
Specifications
APPLICATION DESCRIPTIONS
Adobe Acrobat Reader
The Adobe Acrobat Reader allows you to view, navigate, and print PDF files from across all of the major computing platforms.
Fujitsu BatteryAid Utility (Windows 2000)/ HotKey Utility (Windows XP)
Fujitsu BatteryAid allows you to optimize system power by monitoring and managing battery status. Fujitsu HotKey allows you to monitor and manage the status of the screen brightness and system volume. (See your
BatteryAid online help for more information on the correct way to use this program)
POINT
As your notebook does not support the CPU Clock control, the option is not active within the Power Control menu of BatteryAid.
Drive Image Special Edition (DISE) by PowerQuest
DISE by PowerQuest provides a way to restore your computer if you experience a hard disk crash or other system failure. DISE is used to restore the factory image and restore the system to its original state.
system requires you to enter a password code using the buttons on the 5-button Security Panel. After entering a correct password, your LifeBook notebook resumes system operation.
McAfee.com
VirusScan Online
VirusScan Online, by McAfee.com, is a web-based anti­virus program that can be run from the McAfee.com Web site after loading data or programs onto your Life­Book notebook. It assists in the protection of the data currently residing on your hard disk from destruction or contamination due to computer virus.
(See your online help, or go to the McAfee web site at: http://www.mcafee.com for more information on how and when to run this program)
Netscape 7.0
Netscape 7.0 provides a suite of Internet tools.
Quicken 2003 New User Edition
Quicken 2003 by Intuit is a personal money manage­ment program. It has features such as portfolio manage­ment, account registries, on-line banking and bill paying features.
Intel SpeedStep (Windows 2000)
Intel SpeedStep allows your Lifebook to operate in dual mode. When connected to AC source, the system oper­ates in Maximum Performance mode. When powered by battery, the system switches to Battery Optimized mode to conserve battery life. SpeedStep software is automati­cally loaded when you start your system and appears on the system tray as flags in one of two modes: (1) A checker flag indicates that the system is set for Maximum Performance mode. (2) A blue flag with a green center square indicates that the system is set for Battery Optimized mode. You can change the setting or disable the software by double-clicking the flag icon and changing the settings in the Intel SpeedStep Technology window.
LifeBook Application Panel Software
Your LifeBook notebook is pre-installed with software utilities that let you operate and configure your Life­Book Application Panel. These utilities are found under the Start menu, under Programs, then under LifeBook Application Panel. They include a CD Player, Applica­tion Panel Setup, Application Panel Guide, Activate Panel, Deactivate Panel and E-mail LED Setup.
LifeBook Security Panel Software
LifeBook Security Panel allows you to secure your Life­Book notebook from unauthorized use. If the security system is activated, upon starting your LifeBook note­book or resuming from Suspend mode the security
81
LifeBook E Series Notebook – Section 7
82
8
Glossary
83
LifeBook E Series Notebook – Section 8
84

Glossary

Glossary
AC Adapter
A device which converts the AC voltage from a wall outlet to the DC voltage needed to power your LifeBook notebook.
Active-Matrix Display
A type of technology for making flat-panel displays which has a transistor or similar device for every pixel on the screen.
Auto/Airline Adapter
A device which converts the DC voltage from an auto­mobile cigarette lighter or aircraft DC power outlet to the DC voltage needed to power your LifeBook note­book.
BatteryAid
Utility that allows the user to change the display bright­ness in order to optimize battery life.
BIOS
Basic Input-Output System. A program and set of default parameters stored in ROM which tests and operates your LifeBook notebook when you turn it on until it loads your installed operating system from disk. Information from the BIOS is transferred to the installed operating system to provide it with informa­tion on the configuration and status of the hardware.
Bit
An abbreviation for binary digit. A single piece of information which is either a one (1) or a zero (0).
in specially structured ways to make your overall data handling time faster.
CardBus
A faster, 32-bit version of the PC Card interface which offers performance similar to the 32-bit PCI architecture.
CMOS RAM
Complementary metal oxide semiconductor random access memory. This is a technology for manufacturing random access memor y which requires very low levels of power to operate.
COMM Port
Abbreviation for communication port. This is your serial interface connection.
Command
An instruction which you give your operating system. Example: run a particular application or format a floppy disk.
Configuration
The combination of hardware and software that makes up your system and how it is allocated for use.
CRT
Cathode Ray Tube. A display device which uses a beam of electronic particles striking a luminescent screen. It produces a visual image by varying the position and intensity of the beam.
Data
The information a system stores and processes.
bps
An abbreviation for bits per second. Used to describe data transfer rates.
Boot
To start-up a computer and load its operating system from disk, ROM or other storage media into RAM.
Bus
An electrical circuit which passes data between the CPU and the sub-assemblies inside your LifeBook notebook.
Byte
8 bits of parallel binary information.
Cache Memory
A block of memory built into the microprocessor which is much faster to access than your system RAM and used
DC
Direct current. A voltage or current that does not fluctuate periodically with time.
DDR
Double Data Rate
Fast version of SDRAM that provides twice the band­width of standard SDRAMs.
Default Value
A pre-programmed value to be used if you fail to set your own.
DIMM
Dual-in-line memory module.
DISE
Drive Image Special Edition (DISE) by PowerQuest. Provides a way to restore your computer if you experi-
85
LifeBook E Series Notebook
ence a hard disk crash or other system failure. DISE is used to restore the factory image and restore the system to its original state.
Disk
A spinning platter of magnetic data storage media. If the platter is very stiff it is a hard drive, if it is highly flexible it is a floppy disk, if it is a floppy disk in a hard housing with a shutter it is commonly called a diskette.
Disk Drive
The hardware which spins the disk and has the heads and control circuitry for reading and writing the data on the disk.
Diskette
A floppy disk in a hard housing with a shutter.
DMA
Direct Memory Access. Special circuitry for memory to memory transfers of data which do not require CPU action.
DMI
Desktop Management Interface. A standard that provides PC management applications with a common method of locally or remotely querying and configuring PC computer systems, hardware and software compo­nents, and peripherals.
DOS
Disk Operating System (MS-DOS is a Microsoft Disk Operating System).
Driver
A computer program which converts application and operating system commands to external devices into the exact form required by a specific brand and model of device in order to produce the desired results from that particular equipment.
DVD
Digital Video Disc. This is a form of optical disc storage for video, audio and computer data, envisioned to replace current digital storage formats (CD-ROM, laser and audio CD) because of its capability for storing greater amounts of data. A typical single layer, single­sided DVD, for example, can contain 4.7GB of data and a maximum of 17GB for the double-sided discs.
ECP
Extended Capability Port. A set of standards for high speed data communication and interconnection between electronic devices.
ESD
Electrostatic Discharge. The sudden discharge of elec­tricity from a static charge which has built-up slowly. Example: the shock you get from a doorknob on a dry day or the sparks you get from brushing hair on a dry day.
Extended Memory
All memory more than the 640KB recognized by MS-DOS as system memory.
FCC
Federal Communication Commission.
Floppy Disk
A spinning platter of magnetic data storage media which is highly flexible.
GB
Gigabyte.
Hard drive
A spinning platter of magnetic data storage media where the platter is very stiff.
Hexadecimal
A decimal notation for the value of a 4 bit binary number. (0-9, A, B, C, D, E, F) Example: 2F in hexa­decimal = 00101111 in binary = 47 in decimal.
I/O
Input/Output. Data entering and leaving your LifeBook notebook in electronic form.
I/O Port
The connector and associated control circuits for data entering and leaving your LifeBook notebook in elec­tronic form.
IDE
Intelligent Drive Electronics. A type of control interface for a hard drive which is inside the hard drive unit.
IEEE 1394
A type of data transfer protocol that allows for fast transfer of digital files and data with devices such as digital cameras.
Infrared
Light just beyond the red portion of the visible light spectrum which is invisible to humans.
IR
An abbreviation for infrared.
86
Glossary
IrDA
Infrared Data Association. An organization which produces standards for communication using infrared as the carrier.
IRQ
Interrupt Request. An acronym for the hardware signal to the CPU that an external event has occurred which needs to be processed.
KB
Kilobyte.
LAN
Local Area Network. An interconnection of computers and peripherals within a single limited geographic location which can pass programs and data amongst themselves.
LCD
Liquid Crystal Display. A type of display which makes images by controlling the orientation of crystals in a crystalline liquid.
Lithium ion Battery
A type of rechargeable battery which has a high power­time life for its size and is not subject to the memory effect as Nickel Cadmium batteries.
Modem
A contraction for MOdulator-DEModulator. The equipment which connects a computer or other data terminal to a communication line.
Monaural
A system using one channel to process sound from all sources.
MPU-401
A standard for MIDI interfaces and connectors.
NTSC
National TV Standards Commission. The standard for TV broadcast and reception for the USA.
Operating System
A group of control programs that convert application commands, including driver programs, into the exact form required by a specific brand and model of micro­processor in order to produce the desired results from that particular equipment.
Parallel Port
A connection to another device through which data is transferred as a block of bits simultaneously with a wire for each bit in the block and with other wires only for control of the device not for transfer of data.
LPT Port
Line Printer Port. A way of referring to parallel interface ports because historically line printers were the first and latter the most common device connected to parallel ports.
MB
Megabyte.
Megahertz
1,000,000 cycles per second.
Memory
A repository for data and applications which is readily accessible to your LifeBook notebook’s CPU.
MHz
Megahertz.
MIDI
Musical Instrument Digital Interface. A standard communication protocol for exchange of information between computers and sound producers such as synthesizers.
Partition
A block of space on a hard drive which is set aside and made to appear to the operating system as if it were a separate disk, and addressed by the operating system accordingly.
PCMCIA
PCMCIA is a trademark of the Personal Computer Memory Card International Association. The Personal Computer Memory Card International Association is an organization that sets standards for add-in cards for personal computers.
Peripheral Device
A piece of equipment which performs a specific function associated with but not integral to a computer. Examples: a printer, a modem, a CD-ROM.
Pitch (keyboard)
The distance between the centers of the letter keys of a keyboard.
Pixel
The smallest element of a display, a dot of color on your display screen. The more pixels per area the clearer your image will appear.
87
LifeBook E Series Notebook
POST
Power On Self Test. A program which is part of the BIOS which checks the configuration and operating condition of your hardware whenever power is applied to your LifeBook notebook. Status and error messages may be displayed before the operating system is loaded. If the self test detects failures that are so serious that operation can not continue, the operating system will not be loaded.
Program
An integrated set of coded commands to your computers telling your hardware what to do and how and when to do it.
PS/2
An IBM series of personal computers which established a number of standards for connecting external devices such as keyboards and monitors.
RAM
Random Access Memory. A hardware component of your LifeBook notebook that holds binary information (both program and data) as long as it has the proper power applied to it.
other wires only for control of the device not for transfer of data.
Shadow RAM
A technique of copying data or applications stored in ROM (Read Only Memory) into RAM (Random Access Memory) for access during actual operation. RAM is much faster to access than ROM, however ROM contents are not lost when power is removed. Shadowing allows permanently stored information to be rapidly accessed.
Smart Card
Smart Cards are the same size and shape as credit cards, but they contain an integrated microprocessor chip. The chip can hold a variety of different information, and provides the user with many possible options, such as allowing them to make secure purchases, pay for phone calls, store security information, and provide personal identification and information.
SRAM
Static Random Access Memory. A specific technology of making RAM which does not require periodic data refreshing.
RAM Module
A printed circuit card with memory and associated circuitry which allows the user to add additional memory to the computer without special tools.
Reset
The act of reloading the operating system. A reset erases all information stored in RAM.
Restart
See Reset.
Resume
To proceed after interruption. In your LifeBook note­book this refers to returning to active operation after having been in one of the suspension states.
ROM
Read Only Memory. A form of memory in which infor­mation is stored by physically altering the material. Data stored in this way can not be changed by your LifeBook notebook and does not require power to maintain it.
SDRAM
Synchronous Dynamic Random Access Memory.
Serial Port
A connection to another device through which data is transferred one bit at a time on a single wire with any
Status Indicator
A display which reports the condition of some portion of your hardware. On your LifeBook notebook this is an LCD screen just above the keyboard.
Stereo (audio)
A system using two channels to process sound from two different sources.
Stroke (keyboard)
The amount of travel of a key when it is pressed from resting to fully depressed.
Suspend
To make inoperative for a period of time. Your LifeBook notebook uses various suspension states to reduce power consumption and prolong the charge of your battery.
SVGA
Super VGA.
S-Video
Super Video. A component video system for driving a TV or computer monitor.
System Clock
An oscillator of fixed precise frequency which synchro­nizes the operation of the system and is counted to provide time of day and date.
88
TFT
Thin Film Transistor – A technology for flat display panels which uses a thin film matrix of transistors to control each pixel of the display screen individually.
UL
Underwriters Laboratories – An independent organiza­tion that tests and certifies the electrical safety of devices.
VGA
Video Graphics Array. A video display standard originally introduced by IBM with the PS/2 series of personal computers.
VRAM
Video Random Access Memory. A memory dedicated to video display data and control.
WFM
Wired for Management is Intel’s broad-based initiative to reduce the total cost of ownership(TCO) of business computing without sacrificing power and flexibility.
Glossary
Write Protect
Prevent alteration of the binary state of all bits in a storage media. Example: all information on a device such as a floppy diskette; a block of space in a storage media such as a partition of a hard drive; a file or direc­tory of floppy diskette or hard drive.
XGA
Extended VGA.
89
LifeBook E Series Notebook
90

Regulatory Information

Regulatory Information
NOTICE
Changes or modifications not expressly approved by Fujitsu could void this user’s authority to operate the equipment.
FCC NOTICES Notice to Users of Radios and Television
These limits are designed to provide reasonable protec­tion against harmful interference in a residential installa­tion. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partic­ular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
n
Reorient or relocate the receiving antenna.
n
Increase the separation between the equipment and receiver.
n
Connect the equipment into an outlet that is on a different circuit than the receiver.
n
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device.
Notice to Users of the US Telephone Network
This equipment (FMD MBH7MD33 Modem) complies with Part 68 of the FCC rules, and the requirements adopted by ACTA. On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment; or a product identifier in the format US:AAAEQ##TXXXX. If requested, this infor­mation or number must be provided to the telephone company.
This equipment is designed to be connected to the tele­phone network or premises wiring using a standard jack type USOC RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant.
The ringer equivalent number (REN) of this equipment is 0.0B as shown on the label. The REN is used to deter­mine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local tele­phone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facili­ties, equipment, operations or procedures that could effect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to main­tain uninterrupted service.
If trouble is experienced with this equipment, for repair or warranty information, please refer to the manual or contact Fujitsu PC Corporation, Customer Service. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.
The equipment cannot be used on public coin service provided by the telephone company. Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commis­sion or corporation commission for information).
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this computer does not disable your alarm equip­ment. If you have any questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date an time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such busi­ness, other entity, or individual.
91
LifeBook E Series Notebook
DOC (INDUSTRY CANADA) NOTICES Notice to Users of Radios and Television
This Class B digital apparatus meets all requirements of Canadian Interference-Causing Equipment Regulations.
CET appareil numérique de la class B respecte toutes les exigence du Réglement sur le matérial brouilleur du Canada.
Notice to Users of the Canadian Telephone Network
NOTICE: This equipment (Modem FMD MBH7MD33) meets the applicable Industry Canada Terminal Equip­ment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indi­cating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment.
Before connecting this equipment to a telephone line the user should ensure that it is permissible to connect this equipment to the local telecommunication facilities. The user should be aware that compliance with the certification standards does not prevent service degradation in some situations.
Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu or any equipment failures may give the telecom­munication company cause to request the user to disconnect the equipment from the telephone line.
NOTICE: The Ringer Equivalence Number (REN) for this terminal equipment is 0.0. The REN assigned to each terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equiva­lence Numbers of all the devices does not exceed five.
CAUTION
For safety, users should ensure that the electrical ground of the power utility, the telephone lines and the metallic water pipes are connected together. Users should NOT attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas.
Avis Aux Utilisateurs Du Réseau Téléphonique Canadien
AVIS: Le présent matériel (FMD MBH7MD33 Modem) est conforme aux spécifications techniques d’Industrie Canada applicables au matériel terminal. Cette confor­mité est confirmée par le numéro d’enregistrement. Le sigle IC, placé devant le numéro d’enregistrement, signifie que l’enregistrement s’est effectué conformé­ment à une déclaration de conformité et indique que les spécifications techniques d’Industrie Canada ont été respectées. Il n’implique pas qu’Industrie Canada a approuvé le matériel.
Avant de connecter cet équipement à une ligne télépho­nique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécom­munications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service.
Les réparations de l’équipement de télécommunications doivent être eVectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressément approuvée par Fujitsu, ou toute défaillance de l’équipement peut entraîner la compagnie de télécommunications à exiger que l’utilisateur décon­necte l’équipement de la ligne téléphonique.
AVIS: L’indice d’équivalence de la sonnerie (IES) du présent matériel est de 0.0. L’IES assigné à chaque dispositif terminal indique le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d’indices d’équiva­lence de la sonnerie de tous les dispositifs n’excède pas 5.
AVERTISSEMENT
Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’électricité, les lignes télphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales.
92
UL Notice
This unit requires an AC adapter to operate. Use only UL Listed Class 2 adapter, output rating 19V DC, 4.22 A. Refer to the illustration below for the correct AC Adapter output polarity:
+
CAUTION
To reduce the risk of fire, use only #26 AWG or larger telecommunications line cord.
For Authorized Repair Technicians Only
CAUTION
For continued protection against risk of fire, replace only with the same type and rating fuse.
WARNING
Danger of explosion if Lithium (CMOS) battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufac­turer’s instruction.
Regulatory Information
93
LifeBook E Series Notebook
94
Loading...