Page 1
IP-900E
IP-900D
IP-900ⅡD
Hardware User’s Guide
Page 2
(This page is intentionally left blank)
Page 3
USING IP-900E/IP-900D series SAFELY
Handling of This Manual
The manual contains important information regarding the safe use of IP-900E/IP-900D series. Read
it thoroughly before operating this device. Make sure that users of the device read and understand
thoroughly all safety precautions contained in the manual. Keep this manual in a safe and convenient
location for quick reference.
Fujitsu makes every effort to prevent users and bystanders from injury and to prevent property damage.
To ensure no harm to you and bystanders, and to prevent damage to the device itself, be sure to use this
equipment in accordance with instructions
The following notice is for USA users only.
IP-900E/IP-900D series has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
The following notice is for Canada users only.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
The following notice is for EU (European Union) users only.
This is Class A product of Electromagnetic Interference (EMI) standard. In a domestic environment
this product may cause radio interference in which case the user may be required to make adequate
measures.
This manual includes technology controlled under the Foreign Exchange and Foreign Trade Control
Law of Japan. The manual or a portion thereof must not be exported (or re-exported) without
authorization from the appropriate governmental authorities in accordance with the above law.
IP-900E/IP-900D series is designed and manufactured for use in standard applications such as office
work, personal devices, and household appliances. The product is not intended for special uses (such
as nuclear-reactor control in atomic energy facilities, aeronautic and space systems, air traffic control,
operation control in mass transit systems, medical devices for life support, and missile firing controls in
weapons facilities) where particularly high reliability requirements exist, where the pertinent levels of
safety are not guaranteed, or where a failure or operational error could threaten a life or cause physical
injury (hereafter referred to as "mission-critical" use). Customers considering use of this product for
mission-critical applications must have safety-assurance measures in place beforehand. Moreover,
they are requested to consult our sales representative before embarking on such specialized use.
Copying of and disassembly, decompilation and other forms of reverse engineering of any program
included with this device is prohibited.
Microsoft, Windows, Windows NT, Windows 2000, and Windows XP are registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
in the manual.
IP-900E/IP-900D series
i
Page 4
IMPORTANT NOTE TO USERS
READ THE ENTIRE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
INCORRECT USE OF THE PRODUCT MAY RESULT IN INJURY OR DAMAGE TO
USERS, BYSTANDERS OR PROPERTY.
While FUJITSU has sought to ensure the accuracy of all information in this manual, FUJITSU
assumes no liability to any party for any damage caused by any error or omission contained in this
manual, its updates or supplements, whether such errors or omissions result from negligence, accident,
or any other cause. In addition, FUJITSU assumes no liability with respect to the application or use of
any product or system in accordance with descriptions or instructions contained herein; including any
liability for incidental or consequential damages arising therefrom.
FUJITSU DISCLAIMS ALL WARRANTIES REGARDING THE INFORMATION
CONTAINED HEREIN, WHETHER EXPRESSED, IMPLIED, OR STATUTORY.
FUJITSU reserves the right to make changes to any products described herein without
and without obligation.
No part of this manual shall be reproduced in any way or form without the permission of Fujitsu Limited.
©
All Rights Reserved. Copyright
FUJITSU LIMITED 2008-2009
further notice
IP-900E/IP-900D series
ii
Page 5
PREFACE
Thank you for purchasing the IP-900E/IP-900D series.
IP-900E/IP-900D series are the video transmission unit with the H.264 encoding technology which
performs the high compression ratio, and transmits the SD (Standard Definition) /HD (High Definition) video
and audio signals in real time through even the optical IP network like FTTH. (*1) IP-900E has functions that
encodes SD/HD video signals from a SD/HD camera or similar device and distributes it across the network in
real-time. IP-900D/IP-900IID has functions that decode the encoded SD/HD video signal data received via the
network and displays it on a monitor or other device.
This manual is intended for system designers and system managers who use IP-900E/IP-900D. Readers
are assumed to have a basic knowledge of networks and video distribution.
Figures and tables are described by using IP-900E as a sample. Functions which are not supported by
IP-900D
*1: IP-900E supports only SD video. By adding optional software, IP-900E will be upgraded to support HD
video.
Product operating environment
/IP-900IID are described at each part of functions separately.
August 2009 2nd Edition
• Designed for use in real-time audio/video transmission systems and in the transmission system of
monitoring systems, IP-900E/IP-900D series is intended for indoor use.
Note:
The contents of this manual are subject to change without notice.
IP-900E/IP-900D series
iii
Page 6
ORGANIZATION AND CONTENTS OF THIS MANUAL
The manual consists of five chapters, an appendix, a glossary and an index.
Read Chapters 1 and 2 first for information on installing and connecting the device. Read Chapter 3 for
operating instructions, and Chapter 4 and subsequent chapters can be read as required.
Chapter 1 Preparations
This chapter describes the checks that are required before the start of IP-900E/IP-900D series operation.
Chapter 2 Installation and Connection
This chapter describes conditions for IP-900E/IP-900D series installation and explains how to connect it
to peripheral the devices.
Chapter 3 Operating Instructions
This chapter explains how to power on/off, set up and operate the device.
Chapter 4 Connection Cable Specifications
This chapter contains a classification of how work is implemented, cable connection system diagrams
and cable connector details.
Chapter 5 Troubleshooting
This chapter describes actions to be taken if the device does not operate normally or if an alarm LED
turns on.
Appendix
The appendix contains views of the device and its basic specifications. Installation work and on-site
adjustment preparations are also covered in this section.
Glossary
The glossary defines the technical terms used in this manual.
Index
The index lists keywords and corresponding pages on which the words appear, so necessary items can be
looked up immediately.
IP-900E/IP-900D series
iv
Page 7
WARNING INDICATIONS
This manual uses warning indications to warn of conditions in order to prevent serious injury and
property damage. Warning indications consist of warning markings of specific levels and warning
messages. The warning markings are shown below along with their definitions.
!
WARNING indicates a situation that could lead to serious injury
or loss of life if procedures are not followed correctly.
!
CAUTION indicates a situation that could lead to minor or
CAUTION
Warning indications within text
Warning markings are followed by warning messages. Every warning marking is centered on a line.
Left and right indents are set for warning messages to differentiate them from ordinary text.
Furthermore, the lines immediately before and after warning indications are left blank.
moderate injury and/or damage to the device itself if procedures
are not followed correctly.
(Example)
Possibility of electric shock, fire and damage to the device
Always observe the precautions given below.
This indicates a hazardous situation that could lead to electric shock, fire or
damage to the device.
• Always connect the power cord to a power receptacle for a standard
two-prong plug with ground.
• Connect the device to the power receptacle with a capacity of 1A or
more. When using a power extension cable, be sure that the total
power consumption of all devices connected to the cable does not
exceed the rated capacity of the cable. If a power receptacle with a
low capacity or capacity below the rated value is used, the power
receptacle, extension cable or power distribution wiring may overheat
and start a fire.
Important warning indications are summarized below in “Safety Precautions.”
v
IP-900E/IP-900D series
Page 8
SAFETY PRECAUTIONS
List of important warnings
The table below contains a list of important warning indications.
Indicates a situation that could lead to serious injury or loss of life if procedures
are not followed correctly.
Work type Warning
Normal use Possibility of electric shock and fire
If an excessive heat, smoke, an abnormal odor or an unusual noise is coming from the
device, immediately set its power switch to OFF and remove the power cord plug from
the power receptacle. Then, contact a Fujitsu Service Center.
This indicates a hazardous situation that could lead to fire and electric shock.
Possibility of electric shock and fire
If foreign matter (e.g., water, bits of metal, fluid) gets inside the device, immediately set
its power switch to OFF and remove the power cord plug from the power receptacle.
Then, contact a Fujitsu Service Center.
This indicates a hazardous situation that could lead to fire and electric shock.
Possibility of electric shock and fire
If the device has been dropped or otherwise damaged, immediately set its power switch
to OFF and remove the power cord plug from the power receptacle. Then, contact a
Fujitsu Service Center.
This indicates a hazardous situation that could lead to electric shock.
Possibility of electric shock and fire
To keep foreign matter out, ensure that drink containers and metal objects are not placed
on or near the device.
The presence of foreign matter such as water inside the device creates a hazardous
situation that could lead to electric shock.
Possibility of electric shock and fire
Ensure that no liquid is splashed on the device, making it wet.
The presence of foreign matter such as water inside the device creates a hazardous
situation that could lead to fire and electric shock.
Possibility of electric shock and fire
Ensure that the power cord does not become damaged, and avoid tampering with it.
If the power cord has a heavy object is placed on it, pulled at, bent, or becomes entangled, it
could be damaged as a result. Also, the power cord could be damaged if subjected to heat,
creating a hazardous situation that could lead to fire and electric shock.
Possibility of electric shock
Because this device contains a hazardous voltage section, never open the cover.
Only a service engineer must open the cover.
This warning indicates a hazardous situation that could lead to electric shock.
IP-900E/IP-900D series
vi
Page 9
Work type Warning
Installation
Possibility of electric shock and fire
Do not install the device in the following places because using it there may cause a fire or
electric shock:
• Extremely dusty or dirty place
• Wet or humid location
• Hot location, such as a place where the device is exposed to direct sunlight or is
near heating equipment
• Near products (e.g., speakers) that generate a strong magnetic field
• Location where the temperature is too hot or cold
• In an environment with sharp temperature fluctuations
• Area with poor ventilation
• Near a fire
Possibility of electric shock, fire, and damage to the device
Always observe the precautions given below.
This indicates a hazardous situation that could lead to electric shock, fire and damage to
the device.
• Always connect the power plug to a power receptacle for a standard two-prong plug
with ground.
• Connect the device to a power receptacle with a capacity of 1 A or more. When
using a power extension cable, be sure that the total current consumption of all
devices connected to the cable does not exceed the rated capacity of the cable. If a
power receptacle with a low capacity or capacity below the rated value is used, the
power receptacle, extension cable or power wiring may overheat and start a fire.
vii
IP-900E/IP-900D series
Page 10
Work type Warning
Installation
and
relocation
Clean
Possibility of serious injury and damage to the device
Do not install the device in places where it is exposed to shock and strong vibrations, on
an incline or in unstable locations.
This indicates a hazardous situation that could lead to serious injury or damage to the
device.
Possibility of serious injury and damage to the device
When relocating the device, observe the following precautions to protect against serious
injury and damage to the device:
• Set the power switch to OFF, and disconnect all connected cables. Take care to
avoid getting your feet entangled in the cables.
• To prevent serious personal injury when moving the device, take special care to pay
attention to your surroundings.
Possibility of fire, serious injury and damage to the device
When cleaning the device, observe the following precautions to protect against fire,
serious injury and damage to the device:
• When cleaning the device, please do not use cleaning spray that is including
combustible material. Also, please do not use it around the device.
• When cleaning the device, please wipe off with the cloth squeezing water (or
neutral detergent thinned by water).
• When wiping off, please be careful not to put water into the device from switches
or the spaces.
IP-900E/IP-900D series
viii
Page 11
LABEL
The warning label shown below is affixed to
・ Never remove the label.
・ Be sure to check the label at the bottom of this device before coming to the power supply.
・ The following label is intended for users of the devices.
Mark for rubber feet
MODEL
PART NO.
IP-900E
TA23742-B50X
0.38A-0.20A
0.038kVA-0.048kVA
1φ
認証番号
T
D08-0454001
FUJITSU LIMITED
I T E
1K91
E136004
MADE IN JAPAN
the device.
100V-240V～
50/60Hz
08-10
12345
00001
01A
2.3kg
MODEL
PART NO.
IP-900D
TA23742-B60X
T
FUJITSU LIMITED
E136004
認証番号
I T E
1K91
0.33A-0.17A
0.033kVA-0.041kVA
D08-0454001
100V-240V～
1φ
MADE IN JAPAN
50/60Hz
12345
2.3kg
01A
08-10
00001
ix
MODEL
PART NO.
IP-900IID
TA23742-B61X
T
FUJITSU LIMITED
E136004
認証番号
I T E
1K91
0.35A-0.18A
0.035kVA-0.045kVA
D08-0454001
100V-240V～
1φ
MADE IN JAPAN
50/60Hz
12345
01A
09-08
00001
IP-900E/IP-900D series
2.3kg
Page 12
PRODUCT HANDLING PRECAUTIONS
Maintenance
WARNING
CAUTION
Do not try to repair the device yourself. Contact a Fujitsu Service Center.
Read this manual thoroughly before attempting to operate the device.
If you have any questions, contact a Fujitsu Service Center.
If a problem occurs, contact a Fujitsu Service Center.
The Fujitsu Service Center will ask you to describe the problem, the lamp display status of alarm
LEDs and other details. Check the system for this information.
Connectable devices
Only devices that conform to the device interface specifications (see Appendix 2.3, "Device
Specifications") can be connected. Otherwise, if incompatible devices are connected, the result
may be personal injury and property damage.
Disposal
To dispose of the device, contact a Fujitsu Service Center, or request a specialist to take care its
disposal.
Modification and restoration
Do not use any device that has been modified or rebuilt with refurbished used parts. Doing so
may result in personal injury and property damage.
IP-900E/IP-900D series
x
Page 13
CONTENTS
Chapter 1 Preparations.......................................................................... 1
1.1 Main Features ...................................................................................... 3
1.2 Components......................................................................................... 4
1.3 Basic Application Examples ................................................................. 5
1.4 Part Names .......................................................................................... 6
Chapter 2 Installation and Connection............................................... 11
2.1 Installation Conditions ........................................................................ 13
2.1.1 Environment conditions.......................................................... 13
2.1.2 Installation environment ......................................................... 13
2.1.3 Air flow into and out from the device...................................... 21
2.1.4 Open space required around the device ................................ 22
2.2 Power Supply System Connections................................................. 23
2.2.1 Connection to ground............................................................. 23
2.2.2 Connection to power source .................................................. 24
2.3 Audio and Video Device Connections.............................................. 27
2.3.1 IP-900E (Encoder) ................................................................. 27
2.3.2 IP-900D/IP-900IID (Decoder)................................................. 28
2.4 Connection to Network ....................................................................... 29
2.5 Connection to RS-232C Device....................................................... 30
2.6 CF Card Insertion and Removal ......................................................... 31
Chapter 3 Operation Instructions ....................................................... 33
3.1 Power ON/OFF................................................................................... 35
3.1.1 Powering on............................................................................. 35
3.1.2 Powering off............................................................................. 35
3.2 Device Settings and Operation........................................................... 36
3.2.1 Maintenance page ................................................................... 37
3.2.2 Reboot ..................................................................................... 37
3.3 Operation Management...................................................................... 38
3.3.1 Settings.................................................................................... 38
3.3.2 Log .......................................................................................... 39
3.4 Special Use of MNT Button ................................................................ 40
Chapter 4 Cable Specifications........................................................... 41
4.1 Installation Preparations..................................................................... 43
4.2 Cable and Connector Details.............................................................. 45
Chapter 5 Troubleshooting.................................................................. 53
5.1 Help Information................................................................................. 55
5.2 Alarm LED Lamp Is On ...................................................................... 61
5.3 Maintenance....................................................................................... 62
5.3.1 Maintenance space.................................................................. 62
5.3.2 Change of maintenance parts (Maintenancer only) ................. 63
IP-900E/IP-900D series
I
Page 14
Appendix..................................................................................................65
A.1 Appearance......................................................................................... 67
A.2 Basic Specifications ............................................................................69
A.2.1 External specifications..............................................................69
A.2.2 Environment specifications.......................................................69
A.2.3 Function specifications .............................................................70
A.3 Preparations for Installation Work .......................................................76
A.3.1 Scope of installation work.........................................................76
A.3.2 Unpacking and device check....................................................76
A.3.3 Installation conditions ...............................................................76
A.3.4 Connecting external cables ......................................................76
A.4 Preparations for On-site Turn-up ......................................................77
Glossary and Index .................................................................................81
Glossary.......................................................................................................83
Index ............................................................................................................86
CE Conformity Information...........................................................................88
IP-900E/IP-900D series
II
Page 15
CHAPTER 1
Chapter 1 Preparations
This chapter describes the checks that are required before the start of IP-900E
/IP-900D series operation.
1.1 Main Features ············································································ 3
1.2 Components··············································································· 4
1.3 Basic Application Examples ······················································· 5
1.4 Part Names ················································································ 6
PREPARATIONS
Page 16
(This page is intentionally left blank)
Page 17
Chapter 1 Preparations
1.1 Main Features
1.1
IP-900E/IP-900D series are the video transmission unit with the H.264 encoding technology which
performs the high compression ratio, and transmits the SD (Standard Definition) /HD (High Definition)
video and audio signals in real time through even the optical IP network like FTTH.
IP-900E has functions that encodes SD/HD video signals from a SD/HD camera or similar device and
distributes it across the network in real-time. IP-900D/IP-900IID has functions that decode the encoded
SD/HD video signal data received via the network and displays it on a monitor or other device.
Main Features
Item Specifications
HD-SDI / SD-SDI 1ch [BNC]
Video input
HDMI 1ch [HDMI]
Analog Composite 1ch [BNC]NTSC/PAL
HD-SDI / SD-SDI 1ch [BNC]
Video output
HDMI 1ch [HDMI]
Analog Composite 1ch [BNC] NTSC/PAL
HD/SD-SDI embedded 2ch [BNC], 1 stereo pairs
Audio input
HDMI 2ch [HDMI]
Analog unbalanced 2ch [RCA], 1 stereo pair
HD/SD-SDI embedded 2ch [BNC], 1 stereo pairs
Audio output
HDMI 2ch [HDMI]
Analog unbalanced 2ch [RCA], 1 stereo pair
Network LAN 1ch
[RJ45],
10BASE-T / 100BASE-TX
Data input/output RS-232C 1ch [D-sub9-pin], male connector
CF CARD slot CF CARD 1 Data storage application
Installation conditions Indoor: On a desk, mounted in a rack
Dimensions W: 210 H: 42 D: 300 (mm) Note: Excluding protrusions (i.e., not including feet)
Cooling system Forced air cooling
Power supply 100-240VAC
Weight Maximum 2.3kg
Power consumption 38VA or less @ 100VAC
Temperature
Humidity
-10 to 55°C (No low temperature startup: -10 to -1°C)
5 to 95%RH (No condensing)
*1: IP-900E supports only SD video. By adding optional software, IP-900E will be upgraded to support HD video.
IP-900E
IP-900D
IP-900ⅡD
○
－－
*1
○
－－
*1
－－
○
－
－○
－
○○
－
○○
－－
○
－－
○
－－
○
－－
－
－
○○ ○
○○ ○
○
○
○○
○○
－－
○
○
○
○
○
○
○
3
IP-900E/IP-900D series
Page 18
Chapter 1 Preparations
1.2 Components
1.2
The IP-900E/IP-900D series product package consists of the following components.
Attachments for all series consist of same contents.
･ IP-900E/IP-900D series: 1 pc (cables separate order)
･ Safety manual: 1pc ･ Feet: 4 pcs
･ Holder of power supply cable: 1 pc
IP-900E/IP-900D series
4
Page 19
Chapter 1 Preparations
1.3 Basic Application Examples
1.3
Examples (system configuration) of use of IP-900E/IP-900D series are shown below.
HD
5
IP-900E/IP-900D series
Page 20
Chapter 1 Preparations
1.4 Part Names
1.4
This section gives the name and describes the function of individual parts of IP-900E/IP-900D series.
The diagrams below show the layout of parts on the outside of the device, and the table below lists
the name and describes the function of individual parts.
- IP-900E
Figure Front panel
Figure Rear panel
Part names
No. Name Description
Can be connected to a 100-240VAC commercial power supply by using power
Power inlet connector
(1)
(INPUT 100-240VAC)
Power button
(2)
Power LED (PWR)
(3)
Status LED
(4)
(RDY)
Alarm LED
(5)
(ALM)
AV input status LED
(6)
(INDWN)
Option LED
(7)
(OPT)
LAN port
(8)
(10/100BASE)
Speed LED
(9)
(10)
(100M)
Status LED
(LINK/ACT)
card with a standard two-prong plug with ground.
See Section 2.2.2, “Connection to a Power Source,” for an explanation on using
this connector. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Turns the device on and off.
Turns on when the device is powered on.
Turn on when IP-900E power is on. For more information, see Table 5.3,
“Details of LED Indications,” in Section 5.2.
Turns on when IP-900E operation is abnormal. For more information, see
Table 5.3, “Details of LED Indications,” in Section 5.2.
Audio/Video input setting status indicator and LED that indicates the input off
status during input setting. For more information, see Table 5.3, “Details of
LED Indications,” in Section 5.2.
Turn on when option license is installed. For more information, see Software
guide.
Ethernet 10BASE-T/100BASE-TX communication port. See Section 2.4,
“Connection to a Network,” for an explanation on using this port. See Section
4.2, “Cable and Connector Details,” for cable connection information.
Indicates the status of LAN port. For more information, see Table 5.3, “Details
of LED Indications,” in Section 5.2.
Indicates the speed of LAN port. For more information, see Table 5.3, “Details
of LED Indications,” in Section 5.2.
IP-900E/IP-900D series
6
Page 21
Chapter 1 Preparations
No. Names Description
RS-232C data communication port.
(11)
RS-232C port
(RS-232C)
See Section 2.5, “Connection to an RS-232C Device,” for an
explanation on using this pin. See Section 4.2, “Cable and Connector
Details,” for cable connection information.
Unbalanced audio input terminal.
Audio input
(12)
(ANALOG AUDIO IN) (L), (R)
See Section 2.3, “Audio and Video Device Connections,” for an
explanation on using this terminal. See Section 4.2, “Cable and
Connector Details,” for cable connection information.
Use for an FG connection to the device.
See Section 2.2.1, “Connection to ground,” for an explanation on using
this terminal.
(13)
FG terminal
)
(FG
IP-900E start mode selector switch. when the IP-900E is powered on
Maintenance mode switch
(14)
(MNT)
with this switch held down, it starts in initial start mode.
See section 3.4, “Mode Switch Setting and Operation,” for an
explanation on using this switch.
Digital HDMI video input terminal. 50Ω unbalanced.
(15)
HDMI input
(HDMI)
See Section 2.3, “Audio and Video Device Connections,” for an
explanation on using this terminal. See Section 4.2, “Cable and
Connector Details,” for cable connection information.
Digital HD-SDI video input terminal. 75Ω unbalanced.
SDI video input
(16)
(SDI)
See Section 2.3, “Audio and Video Device Connections,” for an
explanation on using this terminal. See Section 4.2, “Cable and
Connector Details,” for cable connection information.
Analog video input terminal. 75Ω unbalanced.
Video input
(17)
(ANALOG VIDEO IN)
See section 2.3, “Audio and Video Device Connections,” for an
explanation on using this terminal. See Section 4.2, “Cable and
Connector Details,” for cable connection information.
(18)
(19)
(20)
CF CARD slot
AUX port
(AUX)
Test port
Slot in which a CompactFlash
Auxiliary port.
Factory test port.
@
card is inserted.
7
IP-900E/IP-900D series
Page 22
Chapter 1 Preparations
- IP-900D/IP-900IID (Figures is described by using IP-900IID as a sample.)
Figure Front panel
Figure Rear panel
Part names
No. Name Description
Can be connected to a 100-240VAC commercial power supply by using power
Power inlet connector
(1)
(INPUT 100-240VAC)
Power button
(2)
Power LED (PWR)
(3)
Status LED
(4)
(RDY)
Alarm LED
(5)
(ALM)
Decoder LED
(6)
(DEC)
LAN port
(7)
(10/100BASE)
Speed LED
(8)
(9)
(10)
(11)
(12)
(100M)
Status LED
(LINK/ACT)
RS-232C port
(RS-232C)
Audio output
(ANALOG AUDIO OUT)
(L), (R)
FG terminal
(FG
)
card with a standard two-prong plug with ground.
See Section 2.2.2, “Connection to a Power Source,” for an explanation on using
this connector. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Turns the device on and off.
Turns on when the device is powered on.
Turn on when IP-900D/IP-900IID power is on. For more information, see
Table 5.3, “Details of LED Indications,” in Section 5.2.
Turns on when IP-900D
information, see Table 5.3, “Details of LED Indications,” in Section 5.2.
Turn on when IP-900D/IP-900IID is decoding then stream. for more
information, see Table 5.3, “Details of LED Indications,” in Section 5.2.
Ethernet 10BASE-T/100BASE-TX communication port. See Section 2.4,
“Connection to a Network,” for an explanation on using this port. See Section
4.2, “Cable and Connector Details,” for cable connection information.
Indicates the status of LAN port. For more information, see Table 5.3, “Details
of LED Indications,” in Section 5.2.
Indicates the speed of LAN port. For more information, see Table 5.3, “Details
of LED Indications,” in Section 5.2.
RS-232C data communication port.
See Section 2.5, “Connection to an RS-232C Device,” for an explanation on
using this pin. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Unbalanced audio output terminal.
See Section 2.3, “Audio and Video Device Connections,” for an explanation on
using this terminal. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Use for an FG connection to the device.
See Section 2.2.1, “Connection to ground,” for an explanation on using this
terminal.
/IP-900IID operation is abnormal. For more
IP-900E/IP-900D series
8
Page 23
Chapter 1 Preparations
No. Names Description
Maintenance mode switch
(13)
(MNT)
HDMI output
(14)
(HDMI)
SDI video output
(15)
(SDI)
Video output
(16)
(ANALOG VIDEO OUT)
AUX port
(17)
(AUX)
Test port
(18)
IP-900E start mode selector switch. when the IP-900E is powered on with this
switch held down, it starts in initial start mode.
See section 3.4, “Mode Switch Setting and Operation,” for an explanation on
using this switch.
Digital HDMI video output terminal. 50Ω unbalanced.
See Section 2.3, “Audio and Video Device Connections,” for an explanation on
using this terminal. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Digital HD-SDI video output terminal. 75Ω unbalanced.
See Section 2.3, “Audio and Video Device Connections,” for an explanation on
using this terminal. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
There is no SDI video output interface for the IP-900D.
Analog video output terminal. 75Ω unbalanced.
See section 2.3, “Audio and Video Device Connections,” for an explanation on
using this terminal. See Section 4.2, “Cable and Connector Details,” for cable
connection information.
Auxiliary port.
Factory test port.
9
IP-900E/IP-900D series
Page 24
(This page is intentionally left blank)
Page 25
CHAPTER 2
Chapter 2 Installation and Connection
INSTALLATION AND
CONNECTION
This chapter describes conditions for IP-900E/IP-900D series installation and
explains how to connect it to peripheral devices.
Figures described in this chapter are used IP-900E as a sample.
2.1 Installation Conditions······························································ 13
2.2 Power Supply System Connections ······································ 23
2.3 Audio and Video Device Connections ··································· 27
2.4 Connection to Network····························································· 29
2.5 Connection to RS-232C Device············································· 30
2.6 CF Card Insertion and Removal··············································· 31
Page 26
Possibility of serious injury
The power cord and other cables connected to IP-900E/IP-900D series may
become entangled with someone walking close to them, possibly leading to
serious injury and property damage. Clamp the cables to the rack or floor.
Page 27
Chapter 2 Installation and Connection
2.1 Installation Conditions
2.1
This section describes the installation environment, air flow into and out from the device, and the
requirement for open space around the device.
2.1.1 Environment conditions
Ensure that installation site conditions do not exceed 55°C. Under this condition,
IP-900E/IP-900D series can operate in the multiple pile. Otherwise, the operating environment
may damage and shorten the product life of IP-900E/IP-900D series noticeably.
2.1.2 Installation environment
1. 19” rack mounting
Using the mounting kit, it is possible to mount on 19” rack complied EAI standard (1U size).
There are two kinds of rack mounting kit (a possible type equipped with one per 1U and a
possible type equipped with two).
The mounting kit attached must be used to install. When the installation
is unstable, the serious accident may be caused.
- Two IP-900E/IP-900D series per 1U
(1) Check contents of the rack mounting kit.
Coupling fittings
13
Mounting fittings
IP-900E/IP-900D series
Page 28
Chapter 2 Installation and Connection
(2) Check all cables disconnected.
(3) Connect the first device with the coupling fittings using six same screws (M4).
(4) Connect the second device with the coupling fittings using six same screws (M4).
IP-900E/IP-900D series
14
Page 29
Chapter 2 Installation and Connection
(5) Rotate the coupling fittings, and fix with twelve screws (M4).
(Bottom view)
(Top view)
15
IP-900E/IP-900D series
Page 30
Chapter 2 Installation and Connection
(6) Install the mounting fittings on IP-900E/IP-900D series using six same screws(M4).
(7) Install IP-900E/IP-900D series on 19” rack using four screws (M5).
IP-900E/IP-900D series
16
Page 31
Chapter 2 Installation and Connection
A
- One IP-900E/IP-900D series per 1U
(1) Check contents of the rack mounting kit.
(2) Check all cables disconnected.
(3) Install the rack mounting kit A on IP-900E/IP-900D series using three same screws (M4).
B
C
IP-900E/IP-900D series
17
Page 32
Chapter 2 Installation and Connection
(4) Install the rack mounting kit B on IP-900E/IP-900D series using three same screws (M4).
(5) Install the rack mounting kit C on IP-900E/IP-900D series and rack mounting kit B using four
screws (M4).
IP-900E/IP-900D series
18
Page 33
Chapter 2 Installation and Connection
(6) Install IP-900E/IP-900D series on 19” rack using four screws (M5).
19
IP-900E/IP-900D series
Page 34
Chapter 2 Installation and Connection
2. Desk-top installation
Install IP-900E/IP-900D series referring Section 2.1.3, “Air flow into and out from the
device” and Section 2.1.4, “Open space required around the device” after sticking the four
rubber feet (Rack mounting kit is not required).
100V-240V～
0.38A-0.20A
2.3kg
50/60Hz
1φ
0.038kVA-0.048kVA
01A
IP-900E
TA23742-B50X
MODEL
PART NO.
Mark for rubber feet
Safety installation instruction:
1) Multiple pile
The maximum 5 IP-900E/IP-900D series can be piled under the
environment condition specified. Please install considering the
maintenance-ability. When IP-900E/IP-900D series are piled, please fix
them to avoid to fall (Do not cover the air intake.). See Section 2.1.4,
“Open space required around the device” for the installation space.
2) When IP-900E/IP-900D series is installed in a closed or multi-unit rack,
the operating ambient temperature inside of the rack environment may
be greater than room ambient. Therefore, the consideration should be
given to operate in the environment compatible with the specifications
in Appendix 2.2 “Environment Specifications.”
- The consideration for adjustment of the air condition like air
circulation should be given to prevent the internal rack ambient
from exceeding the maximum operating ambient temperature of
IP-900E/IP-900D series.
- The maximum operating ambient temperature for IP-900E/
IP-900D series: 55°C.
08-10
00001
12345
認証番号
T
MADE IN JAPAN
I T E
1K91
FUJITSU LIMITED
E136004
IP-900E/IP-900D series
20
Page 35
Chapter 2 Installation and Connection
3) The installation of IP-900E/IP-900D series in a rack should be such that
the amount of airflow required for safe operation of IP-900E/IP-900D
series is not compromised.
- IP-900E/IP-900D series has ventilation opening at the right and
rear side.
- Do not cover or close these ventilation openings to prevent
overheating.
4) The mounting of IP-900E/IP-900D series in a rack should be such that a
hazardous condition in not archived due to uneven mechanical loading.
To keep stability of the entire rack, please fix the rack to wall or floor
by suitable means.
- Be careful about injury during installation of IP-900E/IP-900D
series into rack.
- Do not install IP-900E/IP-900D series into your rack where
IP-900E/IP-900D series may make the entire rack unstable.
- The weight of IP-900E/IP-900D series with the maximum
configuration: 2.3 kg
5) If IP-900E/IP-900D series is supplied from the power strip or the
service outlet of other units, it may overload the power supply cord of
the power strip or other units.
- Confirm that the current rating of the power strip or the service
outlet exceeds the combined ratings of all equipment is supplying.
- The electrical rating of IP-900E : Rated 100-240 VAC, 50/60 Hz, 1
phase, 0.38 - 0.20 A(IP-900E)/0.33 - 0.17 A(IP-900D) /0.35 - 0.18 A
(IP-900IID).
6) The reliable earthing of the rack-mounted equipment must be
maintained. The particular attention should be given to supply
connections other than direct connections to the branch circuit (e.g., use
of the power strips or the power distribution unit).
Note: The high leakage current may flow through the power strip
earthing conductor if all power supply cords of IP-900E/IP-900D series
are connected to one power strip. The earth connection is essential
before connecting supply. If the power strip is not directly connected to
the branch circuit, the power strip which has the industrial type
attachment plug should be used.
7) For installing, IP-900E/IP-900D series shall be installed near the
wall-outlet and the wall-outlet shall be easily accessible.
2.1.3 Air flow into and out from the device
IP-900E/IP-900D series is forced air cooled. Be sure not to block the air intake/exhaust vents.
Provide an adequate amount of space around the vents.
21
IP-900E/IP-900D series
Page 36
Chapter 2 Installation and Connection
2.1.4 Open space required around the device
Provide the indicated (parts with hatched area) below, cable forming space, operation space and
air intake/exhaust.
For the information of maintenance space, see Section 5.3.1, “Maintenance space.”
100-240V
PWR ALM
FG
100M
OPT
IN
RDY
DWN
MNT
LINK
/ACT
LR
IP-900E/IP-900D series
22
Page 37
Chapter 2 Installation and Connection
2.2 Power Supply System
2.2
Connections
This section explains ground and power-source connections.
2.2.1 Connection to ground
Use a power cord with the standard two-prong plug with ground wire for FG and external ground
connections.
When the exogenous noise influences IP-900E/IP-900D series, connect the FG terminal to an
external ground.
FG terminal (M4)
Figure Connection to ground
23
IP-900E/IP-900D series
Page 38
Chapter 2 Installation and Connection
2.2.2 Connection to power source
IP-900E/IP-900D series operation requires a power supply of 100-240 VAC. Insert the power
cord with the standard two-prong plug with ground into the inlet connector.
The power cord is not supplied with the device. Procure it separately.
Figure Power cord connection
AC cord clamp
Insert the AC cord clamp into the AC cord clamp hole and fix the power cord as shown in
figure above. When remove the AC cord clamp, screw out and remove it with the mounting
kit.
IP-900E/IP-900D series
24
Page 39
Chapter 2 Installation and Connection
USABLE DETACHABLE POWER SUPPLY CORD SET
MODEL Input Connector Cord Attachment Plug cap
North
America
<*1>
<*2>
Europe
<*2>
Australia
U.K
<*2>
100120V
200240V
100240V
100240V
100240V
IEC C-13
Rated 13A, 125V
UL, CSA Approved
IEC C-13
Rated 15A, 250V
UL, CSA Approved
IEC C-13
Rated 10A, 250V
<*1>
IEC C-13
Rated 10A,
250V
IEC C-13
Rated 10A,
250V
Type SJT, No.16 AWG Min.
3-Conductors
(Single phase;2-current carrying
conductors & ground)
UL, CSA Approved
Type SJT, No.14 AWG Min.
3-Conductors
(Single phase; 2-current carrying
conductors & ground)
UL, CSA Approved
CENELEC OC
3X1.0 square mm<*1>
<HAR>
Cable: AS OD 3 X1.0 square mm
e.g.
BS OC 3 X1.00 square mm Rated 10 A. 250 V
NEMA (5-15P)
parallel blade
Rated 13A, 125V
UL, CSA Approved
NEMA (6-15P)
tandem blade
Rated 15 A, 250 V
UL, CSA Approved
Rated 10 A, 250 V
<*1>
Rated 10 A, 250 V
or
ASA
Japan 100V
IEC C-13
Rated 13A,
125V
METI Approved
or <PSE>
PS
E
Korea
Note: *l. Be sure that the detachable proper Supply cord has the approval of the
220V
(Class I)
220V
(Class II)
appropriate safety agencies of the country where the equipment will be used.
*2. Cable length of above Power Supply cord shall be shorter than 4.5 m.
IEC 60320-1
(IEC C-13)
Rated 12A, 250V
or
IEC 60320-1
(IEC C-13)
Rated 3A, 250V
or
Type HVCTF cross section area
1.25 square mm
3-Conductors
(Single phase;2-current
carrying conductors & ground)
METI Approved
or <PSE>
PS
E
Comply with KSC3304.
Type VCTF cross section area 1.25
(0.50 or 1.00 or 2.00) square mm
3-Conductors
(Single phase;2-current
carrying conductors & ground)
Comply with KSC3304.
Type VCTFK cross section area
1.25 (0.50 or 0.75 or 1.00 or 2.00)
square mm
2-Conductors
or
or
NEMA (5-15P)
parallel blade
Rated 13 A, 125 V
METI Approved
or <PSE>
PS
E
Comply with KSC8305.
Rated 12A, 250V
or
Comply with KSC8305.
Rated 12A, 250V
or
25
IP-900E/IP-900D series
Page 40
Chapter 2 Installation and Connection
CERTIFICATION MARKING
Country Agency Certification Mark Country Agency Certification Mark
Austria OVE
Italy IMQ
Belgium CEBEC
Denmark DEMKO
Finland FEI
France UTE
Germany VDE
Possibility of electric shock, fire, and damage to the device
V
DE
Norway NEMKO
Spain AEE
Sweden SEMKO
Switzerland SEV
Always observe the precautions given below.
This indicates a hazardous situation that could lead to electric shock, fire, or
damage to the device.
Always connect the power cord to a power receptacle for the standard
two-prong plug with ground.
Use a power receptacle with a capacity of 1A or more. When using a power
extension cable, be sure that the total power consumption of all devices
connected to the cable does not exceed the rated capacity of the cable. If the
power receptacle capacity is low, or power consumption exceeds the rated value,
the power cord or power wiring may overheat and start a fire.
Possibility of damage to the device
Do not turn on the device until connection of peripheral devices is completed.
Otherwise, the device may be damaged.
100-240 VAC
Using a power cord with the standard two-prong plug with ground, connect
IP-900E/IP-900D series to 100-240 VAC outlet.
Provide a power receptacle for the standard two-prong plug with ground.
IP-900E/IP-900D series
26
Page 41
Chapter 2 Installation and Connection
2.3 Audio and Video Device
2.3
Connections
2.3.1 IP-900E (Encoder)
For audio and video encoding, there are two digital video, one analog video, two digital audio and
two analog audio terminals to connect audio and video output device.
Digital and analog video input
Connect to SDI terminal using coaxial cable with BNC connector and input HD-SDI or
SD-SDI signal. The signal is terminated in 75Ω.
Connect to HDMI terminal using the HDMI cable. The signal is terminated in 50Ω.
Connect to ANALOG VIDEO IN terminal using coaxial cable with BNC connector and input
NTSC/PAL signal. The signal is terminated in 75Ω.
Digital and analog audio input
Connect to ANALOG AUDIO IN (L), (R) using the cable with RCA connector. The
impedance is 54KΩ unbalanced. Inputting a signal outside of the rated value will cause a
problem in terms of audio level and noise. The HD-SDI and HDMI embedded audio is
supported for the digital audio too.
The figure below shows how to connect the digital and analog audio/video cables.
NOTE:
For details about connectors and cables, see Section 4.2, “Cable and Connector
Details.” For electrical specifications, see Appendix 2.3, “Function Specifications.”
100-240V
PWR ALM
FG
100M
OPT
IN
RDY
DWN
MNT
LINK
/ACT
LR
Video & Audio Output Device
Figure Audio and video output device connections
27
IP-900E/IP-900D series
Page 42
Chapter 2 Installation and Connection
2.3.2 IP-900D/IP-900IID (Decoder)
For audio and video decoding, there are one or two digital video, one analog video, one digital
audio and two analog audio terminals to connect and audio and video input device.
Digital and analog video output
Connect to SDI OUT using coaxial cable with BNC connector and output HD/SD-SDI signal.
SDI output can be supported for
Connect to HDMI terminal using the HDMI cable. The signal is terminated in 50Ω.
Connect to ANALOG VIDEO OUT using coaxial cable with BNC connector and output
NTSC or PAL signal. The signal is terminated in 75Ω.
Digital audio output
The HDMI embedded audio is supported.
Analog audio output
Connect to ANALOG AUDIO OUT (L), (R) using the cable with RCA connector. The
impedance is 1KΩ unbalanced. Inputting a signal outside the rated value will cause a
problem in terms of audio level and noise.
The figure below shows how to connect the digital and analog audio/video and the reference clock
cables.
NOTE:
For details about connectors and cables, see Section 4.2, “Cable and Connector Details.”
For electrical specifications, see Appendix 2.3, “Function Specifications.”
100-240V
Figure Audio and video input device connections
IP-900IID.
PWR ALM
RDY
FG
100M
DEC
MNT
/ACT
LINK
Video & Audio Input Device
LR
IP-900E/IP-900D series
28
Page 43
Chapter 2 Installation and Connection
2.4 Connection to Network
2.4
To connect IP-900E/IP-900D series to a LAN device, connect the LAN device to the LAN
communication port of IP-900E/IP-900D series using a LAN cable (UTP cable). The LAN
communication port specification of IP-900E/IP-900D series is 10BASE-T/100BASE-TX.
The figure below shows the connection method.
NOTE:
For details about connectors and cables, see Section 4.2, “Cable and Connector Details.”
For electrical specifications, see Appendix 2.3, “Function Specifications.”
100-240V
PWR ALM
OPT
IN
RDY
DWN
FG
MNT
100M
LINK
/ACT
LR
Hub, Router, PC, etc.
Figure Connection to a network
CAUTION
Please do not provision the IP address below.
・ IP address commonly unused（0.0.0.0，255.255.255.255，etc…）
・ Loop back address (127.xxx.xxx.xxx)
・ Class D and Class E addresses
・ IP address already used
For more information, see IP-900E/IP-900D series Software User’s Guide.
IP-900E/IP-900D series
29
Page 44
Chapter 2 Installation and Connection
2.5 Connection to RS-232C
2.5
Device
The [RS-232C] connector of IP-900E/IP-900D series is the RS-232C communication terminal. The
terminal of IP-900E/IP-900D series is the D-sub 9 pins (male) and the specification is DTE. Use a
cross connection or straight cable corresponding to the connected device. See Section 4.2, “Cable and
Connector Details.”
The figure below shows the connection method.
NOTE:
For details about connectors and cables, see Section 4.2, “Cable and Connector Details.”
For electrical specifications, see Appendix 2.3, “Function Specifications.”
100-240V
FG
PWR ALM
RDY
100M
OPT
IN
DWN
MNT
LINK
/ACT
LR
D-sub9pin（female）
Data communication
device
Figure Connection to RS-232C input/output device
IP-900E/IP-900D series
30
Page 45
Chapter 2 Installation and Connection
2.6 CF Card Insertion and Removal
2.6
IP-900D/IP-900IID doesn’t support CF card slot.
In order to insert the CF card, the front cover of IP-900E must be opened by screwing out the cover.
No storage card is supplied with IP-900E. It can be procured separately, depending on the system.
The CF card removal procedure is shown below.
Please turn off the power to insert or remove the CF card.
Please contact Fujitsu office what type of CF card is available to use.
IP-900E/IP-900D series
31
Page 46
(This page is intentionally left blank)
Page 47
CHAPTER 3
Chapter 3 Operation Instructions
OPERATION INSTRUCTIONS
This section explains how to power on/off, setup and operate the device.
Figures or Web screens described in this chapter are used
IP-900E/IP-900D/IP-900IIDs’ as a sample. Operations and descriptions
are common for all equipments.
3.1 Power ON/OFF ········································································ 35
3.2 Device Settings and Operation ················································36
3.3 Operation Management ···························································38
3.4 Special Use of MNT Button ······················································ 40
Page 48
(This page is intentionally left blank)
Page 49
3.1 Power ON/OFF
3.1
This section explains how to power on/off the IP-900E/IP-900D series.
3.1.1 Powering on
When the power button on the front panel is set to the [ | ] position, the PWR LED turns on.
When IP-900E/IP-900D series completes preparations for operation, the RDY LED turns on.
Chapter 3 Operation Instructions
3.1.2 Powering off
When the power button on the rear panel is set to the [O] position, the device is powered off and
the PWR LED turns off.
35
IP-900E/IP-900D series
Page 50
Chapter 3 Operation Instructions
3.2 Device Settings and Operation
3.2
■Setup Procedure
The setup procedure is shown below.
See Software User’s Guide for the procedure of the software installation and the each setting.
- Check if IP-900 is disconnected to user’s network.
Connect IP-900 and PC
using UTP cable
Power ON
- Connect using UTP cable.
- When connect through LAN port, the default IP address and subnet
mask are 10.0.0.1 and 255.0.0.0 respectively. Assign 10.xxx.xxx.xxx for PC.
(ex. IP address: 10.0.0.2, Subnet mask: 255.0.0.0)
for PC.
See Section 3.3, “Operation Management.”for more details.
Change network settings
Reboot
- After rebooted, start setting from WEB GUI.
See Section 3.3, “Operation Management” of the software user’s
guide for mode details.
- After rebooted, connected to the user’s network and set up the various
parameters. See Section 3.2.2, “Reboot” for more details.
Connect user’s network
Start settings and operations
(Refer the software user’s guide)
■Web browser recommended
The recommended web browser is as follow.
- Internet Explorer 6.0 SP2 or later
IP-900E/IP-900D series
36
Page 51
This section briefly explains the basic functions of the setup pages.
3.2.1 Maintenance page
Clicking the Settings, Log or Software management menu in the left frame of the browser displays
the corresponding device setting page so that you can set or display items.
3.2.2 Reboot
Clicking the button displayed in the left frame of the browser reboots the device. When
you click the button, the following dialog box shown below appears for confirmation. Click OK to
reboot.
Chapter 3 Operation Instructions
37
IP-900E/IP-900D series
Page 52
Chapter 3 Operation Instructions
3.3 Operation Management
3.3
3.3.1 Settings
On the PC Web browser, specify the IP address of IP-900E/IP-900D series (10.0.0.1) [example:
http://10.0.0.1/] to set up a connection to the http server of the IP-900E/IP-900D series.
When connect through LAN port, set the PC IP address and subnet mask as follows:
- IP address : 10.xxx.xxx.xxx
(xxx is a number from 0 to 255, excluding 10.0.0.0, 10.0.0.1, and 10.255.255.255.)
［Example: 10.0.0.2］
- Subnet mask : 255.0.0.0
The page shown below first appears (Initial page at power-on immediately after shipment from the
factory). The IP addresses and subnet masks set for the IP-900E/IP-900D series on the LAN, and
the gateway setting are displayed.
When you operate the IP-900E/IP-900D series with the default settings after
shipment from the factory, disconnect the IP-900E/IP-900D series from your
network. Connect it to the setting terminal via a Hub or directly. Set up the
IP-900E/IP-900D series to meet the requirements for your network and then
connect the IP-900E/IP-900D series to the network. If you connect the
IP-900E/IP-900D series to your network with the default settings, an unexpected
problem may be caused with your network.
IP-900E/IP-900D series
38
Page 53
3.3.2 Log
Click Log in the left frame of the browser to display the log information page in the right frame of
the browser, where you can check alarm log information on the IP-900E/IP-900D series.
Clicking in the right frame deletes all log information.
* Up to 1,000 log items can be saved. Log items exceeding 1,000 items overwrite existing items
beginning with the chronologically oldest item. (Ten pages of log information, 100 items per page,
are saved.)
For details, see IP-900E/IP-900D series Software User's Guide.
Chapter 3 Operation Instructions
39
IP-900E/IP-900D series
Page 54
Chapter 3 Operation Instructions
3.4 Special Use of MNT Button
3.4
You can start IP-900E/IP-900D series by turning on the power while holding down the [MNT]
Button (for about 10 seconds) until the RDY LED begins blinking in orange. Doing so starts the
IP-900E/IP-900D series with the initial IP address and subnet mask with which the IP-900E/
IP-900D series is shipped from the factory (IP address 10.0.0.1, Subnet mask: 255.0.0.0).
Use this function when making initial settings for IP-900E/IP-900D series from a control
terminal (such as a PC having a LAN interface) (*1).
*1 When you operate the IP-900E/IP-900D series with the default IP address, connect the device
to a control terminal and make setting from the terminal with the device disconnected from
your network.
After making settings according to the requirements for your network, connect the device to
the network. If the device with the default settings made at the factory is connected to the
network, an unexpected problem may occur with your network.
If you start IP-900E/IP-900D series while holding the [MNT] button, set the IP addresses and
subnet masks of the control terminal to connect as follows:
- IP address : 10.xxx.xxx.xxx
(xxx is any number from 0 to 255, excluding 10.0.0.0, 10.0.0.1, and 10.255.255.255.)
- Subnet mask : 255.0.0.0
IP-900E/IP-900D series
40
Page 55
CHAPTER 4
Chapter 4 Cable Specifications
CABLE SPECIFICATIONS
This chapter contains a type of how work is implemented, cable connection system
diagrams, and cable connector details
4.1 Installation Preparations··························································· 43
4.2 Cable and Connector Details ··················································· 45
Page 56
(This page is intentionally left blank)
Page 57
Chapter 4 Cable specifications
4.1 Installation Preparations
4.1
A type of IP-900E/IP-900D series installation work is shown below.
(IP-900E)
43
IP-900E/IP-900D series
Page 58
Chapter 4 Cable specifications
Cable (3) shown below are not be able to connect with IP-900D.
IP-900D/IP-900IID External device
RCA
(1) Analog audio cable
RCA
(2) Analog audio cable
Analog audio input device
(Speaker, etc)
BNC
(3) Coaxial cable
BNC
(4) Coaxial cable
Digital video (HD/SD-SDI) input device
(Incld embedded audio)
(Display, etc)
Analog video input device
(Display, etc)
D-sub9
(5) RS-232C cable
HDMI
(6) HDMI cable
RJ45
(7) LAN cable
Device with RS-232C interface
Digital video (HDMI) input device
(Display, etc)
Device with LAN interface (HUB, etc)
(8) Power cable
(separate order)
Power source 100-240VAC
(IP-900D/IP-900IID)
When constructing a system that uses IP-900E/IP-900D series, consideration must be given so that
its boundary between IP-900E/IP-900D series and other devices is similar to that shown in the above
figure. Since the type of work may change depending on the system, procure equipment and perform
work based on consultations with a system designer.
IP-900E/IP-900D series
44
Page 59
Chapter 4 Cable specifications
4.2 Cable and Connector Details
4.2
(1) SDI VIDEO cable
(2) Analog VIDEO cable
1
2
Front view
BNC BNC
<IP-900E> <External device>
SG
①
②
Mono
SIGNAL
NTSC
GEN LOCK
Coaxial cable with BNC connector
Product code: TBD
Coaxial cable 75Ω
(3C-2V or more)
30m (Coaxial cable 75Ω 3C-2T)Color
200m (Coaxial cable 75Ω 3C-2T)
200m (Coaxial cable 75Ω 3C-2V)
①
②
SIGNAL
SG
45
IP-900E/IP-900D series
Page 60
Chapter 4 Cable specifications
(3) Analog AUDIO cable
IP-900E/IP-900D series
46
Page 61
(4) HDMI cable
Chapter 4 Cable specifications
47
IP-900E/IP-900D series
Page 62
Chapter 4 Cable specifications
(6) RS-232C cable
・・・・・・
9
・・・・・・
Front view
D-sub9 (female)
<IP-900E>
（DTE）
15
6
D-sub 9 pin (male)
#4-40 retainer screw
D-sub 9 pin
CD
RD
SD
DTR(ER)
SG
DSR(DR)
RTS(RS)
CTS(CS)
RI
(female)
○
01
○
02
○
03
○
04
○
05
○
06
○
07
○
08
○
09
RS-232C DTE
<External device side>
○
○
○
○
○
○
○
○
○
CD
RD
SD
DTR(ER)
SG
DSR(DR)
RTS(RS)
CTS(CS)
RI
<External device>
(DTE)
<IP-900E>
（DTE）
RS-232C DCE
D-sub 9 pin
(female)
○
01
CD
○
02
RD
○
03
SD
○
SG
04
○
05
○
06
○
07
○
08
○
09
RI
DTR(ER)
DSR(DR)
RTS(RS)
CTS(CS)
15 m (Twisted pair cable with shield 24AWG)
○
○
○
○
○
○
○
○
○
CD
RD
SD
DTR(ER)
SG
DSR(DR)
RTS(RS)
CTS(CS)
<External device>
(DCE)
RI
IP-900E/IP-900D series
48
Page 63
(7) LAN cable
Chapter 4 Cable specifications
RJ45 RJ45
12345678
<IP-900E> <External device>
Front view
10/100BASE
<IP-900E> <External device>
TD+
TDRD+
RD-
①
②
③
④
⑤
⑥
⑦
<Straight connection>
⑧
100m : TPCBL-B100
：100m UTP cable（Category 5 or more)10/100BASE
5m : TPCBL-B005
10m : TPCBL-B010
50m : TPCBL-B050
①
②
③
④
⑤
⑥
⑦
⑧
TD+
TDRD+
RD-
<IP-900E> <External device>
TD+
TDRD+
RD-
①
②
③
④
⑤
⑥
⑦
⑧
①
②
③
④
⑤
⑥
⑦
⑧
TD+
TDRD+
RD-
49
IP-900E/IP-900D series
Page 64
Chapter 4 Cable specifications
(9) 100 - 240 VAC power cord
The power supply cable is not contained in this device. Please prepare the cable which suits the
country which uses it.
Connector specifications
FG
The form of an outlet changes
with countries which use it.
Front view of cable connector
Connector pin assignment
MODEL Input Connector Cord Attachment Plug cap
North
America
<*1>
<*2>
Europe
<*2>
Australia
L1 L2
Other
100120V
200240V
100240V
100240V
USABLE DETACHABLE POWER SUPPLY CORD SET
IEC C-13
Rated 13A, 125V
UL, CSA Approved
IEC C-13
Rated 15A, 250V
UL, CSA Approved
IEC C-13
Rated 10A, 250V
<*1>
IEC C-13
Rated 10A,
250V
<Device side>
L1
L2
FG
If a power cord with a ground wire cannot be used, connect the FG terminal to
{
an external ground . (See Section 2.2.1, "Connection to ground.")
c
c
c
Type SJT, No.16 AWG Min.
3-Conductors
(Single phase;2-current carrying
conductors & ground)
UL, CSA Approved
Type SJT, No.14 AWG Min.
3-Conductors
(Single phase; 2-current carrying
conductors & ground)
UL, CSA Approved
CENELEC OC
3X1.0 square mm<*1>
<HAR>
Cable: AS OD 3 X1.0 square mm
To standard two - prong power receptacle with ground
(x: length specification)
L1
c
L2
c
FG
c
NEMA (5-15P)
parallel blade
Rated 13A, 125V
UL, CSA Approved
NEMA (6-15P)
tandem blade
Rated 15 A, 250 V
UL, CSA Approved
Rated 10 A, 250 V
<*1>
e.g.
Rated 10 A, 250 V
U.K
<*2>
Japan
100240V
100V
IEC C-13
Rated 10A,
250V
IEC C-13
Rated 13A,
125V
METI Approved
IP-900E/IP-900D series
or <PSE>
PS
E
BS OC 3 X1.00 square mm Rated 10 A. 250 V
Type HVCTF cross section area
1.25 square mm
3-Conductors
(Single phase;2-current
carrying conductors & ground)
METI Approved
or <PSE>
PS
E
50
or
ASA
NEMA (5-15P)
parallel blade
Rated 13 A, 125 V
METI Approved
or <PSE>
PS
E
Page 65
Chapter 4 Cable specifications
Korea
220V
(Class I)
IEC 60320-1
(IEC C-13)
Rated 12A, 250V
Comply with KSC3304.
Type VCTF cross section area 1.25
(0.50 or 1.00 or 2.00) square mm
3-Conductors
Comply with KSC8305.
Rated 12A, 250V
(Single phase;2-current
or
carrying conductors & ground)
or
or
220V
(Class II)
IEC 60320-1
(IEC C-13)
Rated 3A, 250V
or
Comply with KSC3304.
Type VCTFK cross section area
1.25 (0.50 or 0.75 or 1.00 or 2.00)
square mm
2-Conductors
or
Comply with KSC8305.
Rated 12A, 250V
or
Note: *l. Be sure that the detachable proper Supply cord has the approval of the
appropriate safety agencies of the country where the equipment will be used.
*2. Cable length of above Power Supply cord shall be shorter than 4.5 m.
CERTIFICATION MARKING
Country Agency Certification Mark Country Agency Certification Mark
Austria OVE
Italy IMQ
Belgium CEBEC
Denmark DEMKO
Finland FEI
France UTE
Germany VDE
V
DE
Norway NEMKO
Spain AEE
Sweden SEMKO
Switzerland SEV
51
IP-900E/IP-900D series
Page 66
Chapter 4 Cable specifications
(This page is intentionally left blank)
IP-900E/IP-900D series
52
Page 67
CHAPTER 5
Chapter 5 Troubleshooting
TROUBLESHOOTING
This section explains how to power on/off, setup and operate the device.
This chapter describes actions to be taken if the device does not operate normally or
if an alarm LED turns on.
Figures described in this chapter are used IP-900Es’ as a sample.
5.1 Help Information······································································· 55
5.2 Alarm LED Lamp Is On ···························································· 61
5.3 Maintenance ············································································62
Page 68
(This page is intentionally left blank)
Page 69
Chapter 5 Troubleshooting
5.1 Help Information
5.1
If a problem is found in device operation, take recommended action described in the table below,
according to the applicable conditions. If the action does not solve the problem, contact a service
representative.
Possibility of electric shock
Contact your system administrator before checking the voltage of a power
outlet. Otherwise, electric shock may occur.
Table 5.1.1 Problem descriptions and recommended actions(IP-900E)
No. Class Status Description Recommended action
1. Is the power cable connected?
Power cannot
be turned on.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Power
The ALM LED
is blinking.
Device
The ALM LED
is on.
The LEDs
excluding LAN
are on.
Data
communication
Data
is disabled.
The INDWN
lamp lights in
orange.
Video
The INDWN
lamp blinks in
orange.
Is the outlet voltage normal?
Check the log information from the
browser.
The temperature inside the device
has risen to the critical level, the
fan speed has fallen, or a CF card
access error has occurred.
The device is faulty.
Is the ambient temperature of the
device higher than that in the
specifications?
Is there any shielding material in
the installation space?
Is the port setting correct? Check the data input-output port setting.
Is the data input/output device
operating normally?
Are the device and the
communication destination device
correctly connected?
Is the power to the video/audio
output device (such as a camera)
selected for input turned on?
Is this device correctly connected
to the video/audio output device?
The synchronization slipping
occurs for encoder or the reference
clock input fault occurs for
decoder.
Make sure that the power cable is properly
connected to the outlet.
Measure the voltage with a tester to confirm
that the voltage is normal.
If another device is connected to the same
outlet, check the operation of the device.
If the ambient temperature of the device is
too high, make proper arrangements to
lower the ambient temperature. If there is
any shielding material in the installation
space, remove it.
If the fan speed is low, the fan needs to be
replaced. Contact a Fujitsu Service Center.
In the case of a CF card access error, restart
the device. If the problem persists, contact
a Fujitsu Service Center. The CF card or
the device needs to be replaced.
Troubleshoot from the control terminal.
(For details, see the software manuals.)
Adjust the temperature so that the ambient
temperature of the device meets the
specification's condition.
Remove the shielding material.
Check the operation of the data input/
output device.
Check cable connections between the device
and communication destination device and
the cable pin assignments.
Verify the power supply and operation of
the video/audio output device selected for
input.
Check the cable connection between this
device and video/audio output device.
Make sure that the video input signal for
encoder or the reference clock input signal
for decoder is set correctly.
55
IP-900E/IP-900D series
Page 70
Chapter 5 Troubleshooting
No. Class Status Description Recommended action
12.
13.
Has the monitor on the receiving
side been powered on?
Has the device on the receiving
side been powered on?
Check the power and operation of the
monitor.
Check the power and operation of the
device on the receiving side.
14.
No image can
15.
16.
17.
18. Is the RDY LED turned on orange?
19.
20. Has the encoder started encoding? Set the encoder to start encoding.
be output on the
receiving side
(black screen).
Video
Blue/gray
screen is output.
Is the device on the receiving side
and monitor correctly connected?
Did the device on the receiving
side generate an alarm?
Does a color bar or gray screen
appear on the receiving side if
image input of the device is set to
non-input? (Since this operation
generates an alarm, obtaining the
system administrator’s approval
before conducting this test.)
Is the RDY LED blinking?
Is the ALM LED blinking?
Check connections between the device on
the receiving side and the monitor.
If an alarm is generated, refer to the relevant
operating manuals on the receiving side, and
take appropriate corrective action.
If the blue screen is displayed, the receiving
side can be assumed to be operated
normally.
Verify that the correct image is input in the
device.
The hardware system is operating while the
RDY LED is blinking. Wait until the
LED remains on.
The device is started in the maintenance
mode.
Reboot the device.
ALM LED blinks when IP address
obtaining is on going or releasing. Check IP
address setting (For more information, refer
the Software User’s Guide).
21. Has the decoder started decoding? Set the decoder to start decoding.
22. Is the streaming setting correct?
23.
24.
25.
26.
Image/audio
output is
distorted.
The image
output is
distorted.
(Analog input
case)
Is the network normal? Refer to “Network” in this table.
Is packet loss occurring on the
decoder?
Is the setting of encoder PAL when
the camera or display is NTSC
type?
Is the setting of encoder NTSC
when the camera or display is PAL
type?
Make the correct streaming setting of this
device and the encoder by referring to the
Software User’s Guide.
If so, confirm the followings.
・Is system bit rate exceeding connected
network capacity?
・Are FEC/ARQ settings in this device and
the opposed device correct?
・Are the network device and LAN port
settings (AUTO, Full/Half-duplex, etc) the
same?
Change encoder setting from PAL to NTSC.
(Check decoder setting too.)
Change encoder setting from NTSC to PAL.
(Check decoder setting too.)
IP-900E/IP-900D series
56
Page 71
Chapter 5 Troubleshooting
No. Class Status Description Recommended action
Encoder is working normal.
If this problem improves normal when
changing ON or OFF, the input or output
signal is bigger or smaller than the
normal range.
Check the device connected.
Encoder is working normal.
The iris adjustment of the camera is
possibly necessary.
Encoder is working normal.
If this problem improves normal when
changing ON or OFF, the input or output
signal is bigger or smaller than the normal
range.
Check the device connected.
Encoder is working normal.
The iris adjustment of the camera is
possibly necessary.
Select an item other than “None” and set
audio to be encoded.
Check the power and operation of the
receiving unit.
Check the connection between the receiving
unit and speakers.
If an alarm was generated, refer to operating
manual of the receiving unit.
If pulling out the cable from the device
eliminates the noise, audio signals may have
noise. Check the audio output device.
If pulling out the line input cable from the
receiving device does not eliminate the
noise, the device can be assumed to be
operating normally. Check the receiving
unit.
If so, confirm the followings.
・Is system bit rate exceeding connected
network capacity?
・Are FEC/ARQ settings of this device and
the opposed device correct?
・Are the network device and LAN port
settings (AUTO, Full/half-duplex, etc) the
same?
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
The video
contents look
whitish.
(Analog input
case)
Video
The vide
contents look
dark.
Spoken words
cannot be heard
on the receiving
side.
Audio
Noise is
generated on
the receiving
side.
When AGC setting of encoder
change ON or OFF, the video
contents improve normal.
When AGC setting of encoder
change ON or OFF, the video
contents does not improve normal.
When AGC setting of encoder
change ON or OFF, the video
contents improve normal.
When AGC setting of encoder
change ON or OFF, the video
contents does not improve normal.
Isn’t “None” selected in the audio
format setting of this device?
Has the receiving unit been
powered on?
Are connections correct between
the receiving unit and speakers?
Was an alarm generated, refer to
operating manual of the receiving
unit?
Does pulling out the audio input
cable fro the device eliminate the
noise?
Is the receiving unit operating
normally?
Isn’t packet loss occurring on the
decoder?
38.
39.
40.
The LINK/ACT
LED for the
LAN port is not
turned on.
Network
Device setting
through a LAN
is disabled.
Is the power to the communication
destination device turned on?
Are the LINK LEDs on this device
and the hub turned on?
Is the IP address specified from the
Web browser correct?
57
Verify the power supply and operation of
the communication destination device.
If the LINK LEDs are not ON, the LAN
cable is not connected. Connect the LAN
cable correctly.
Specify a correct IP address from the Web
browser on the control terminal.
IP-900E/IP-900D series
Page 72
Chapter 5 Troubleshooting
No. Class Status Description Recommended action
Make correct settings by referring to the PC
user's guide and OS handbook. If this device is
started with the default settings made before
shipment from the factory, see "Section 3.3.1,
"Settings," for the network settings for the
control terminal PC.
41.
Are the network settings (IP
address, subnet mask, etc.) on the
control terminal PC correct?
42.
Network
Is a reply received in response to a
PING command issued to the IP
address of the device?
If a reply is not received, turn on the power to
the device while holding down the MNT button
to start the system with the default IP address
(10.0.0.1) set before shipment from the factory.
Confirm the IP address. If the problem
persists, check the status on the LAN. For
information on this startup procedure, see
Section 3.6, "Special Use of Cancel Key."
Table 5.1.1 Problem descriptions and recommended actions(IP-900D/IP-900IID)
No. Class Status Description Recommended action
1 Is the power cable connected?
Power cannot
2
be turned on.
Power
Is the outlet voltage normal?
Check the log information from the
browser.
3
The ALM LED
is blinking.
The temperature inside the device
has risen to the critical level, the fan
speed has fallen, or a CF card
access error has occurred.
Device
4
The ALM LED
is on.
The device is faulty.
Is the ambient temperature of the
The LEDs
5
excluding LAN
are on.
device higher than that in the
specifications?
Is there any shielding material in
the installation space?
Make sure that the power cable is properly
connected to the outlet.
Measure the voltage with a tester to confirm that
the voltage is normal.
If another device is connected to the same
outlet, check the operation of the device.
If the ambient temperature of the device is too
high, make proper arrangements to lower the
ambient temperature. If there is any shielding
material in the installation space, remove it.
If the fan speed is low, the fan needs to be
replaced. Contact a Fujitsu Service Center.
In the case of a CF card access error, restart the
device. If the problem persists, contact a
Fujitsu Service Center. The CF card or the
device needs to be replaced.
Troubleshoot from the control terminal.
(For details, see the software manuals.)
Adjust the temperature so that the ambient
temperature of the device meets the
specification's condition.
Remove the shielding material.
6
7
8
Data
communication
Data
is disabled.
IP-900E/IP-900D series
Is the port setting correct? Check the data input-output port setting.
Is the data input/output device
operating normally?
Are the device and the
communication destination device
correctly connected?
58
Check the operation of the data input/ output
device.
Check cable connections between the device
and communication destination device and the
cable pin assignments.
Page 73
Chapter 5 Troubleshooting
No. Class Status Description Recommended action
9
10 Is the power of device on? Check that PWR LED lights.
11
12
No image can be
output on the
13 Is ALM LED turned on? Refer to clause 3 in this table.
receiving side
(black screen).
Has the device on the receiving
side been powered on?
Is the device correctly
connected to the monitor?
Is the video output setting of this
device correct?
Does a color bar or gray screen
appear on the receiving side if
image input of the Encoder
14
device is set to non-input? (Since
this operation generates an alarm,
obtaining the system
administrator’s approval before
conducting this test.)
15 Is the RDY LED blinking?
16
Is the RDY LED turned on
orange?
Check the power and operation of the device on
the receiving side.
Check the connection between the device and
monitor.
Make sure the video output setting of this
device allows the monitor to display.
If the blue screen is displayed, the receiving side
can be assumed to be operated normally.
Verify that the correct image is input in the
Encoder device.
The hardware system is operating while the
RDY LED is blinking. Wait until the LED
remains on.
The device is started in the maintenance mode.
Reboot the device.
17 Is DEC LED off? Decoder is not working. Check the followings.
18
19
Displayed blue
screen on the
receiving side.
Has the decoder started
decoding?
Has the encoder started
encoding?
Set the decoder to start decoding.
Make sure that the encoder is starting to encode.
Make correct live stream settings of this device
20 Is the streaming setting correct?
21
22
Video
Received image
sometimes freezes
or distorted.
Is the network normal? Refer to “Network” in this table.
Is packet loss occurring?
(Is DEC LED blinking?)
Is the setting of encoder PAL
23
24
The image output
is distorted.
(Analog output
case)
when the camera or display is
NTSC type?
Is the setting of encoder NTSC
when the camera or display is
PAL t ype?
and encoder by referring to the Software User's
Guide.
Refer to clause 42 in this table
Change decoder setting from PAL to NTSC.
(Check encoder setting too.)
Change encoder setting from NTSC to PAL.
(Check encoder setting too.)
Encoder is working normal.
If this problem improves normal when changing
ON or OFF, the input or output signal is bigger
or smaller than the normal range.
Check the device connected.
Encoder is working normal.
The iris adjustment of the camera is possibly
necessary.
25
26
The video
contents look
whitish.
When AGC setting of encoder
change ON or OFF, the video
contents improve normal.
When AGC setting of encoder
change ON or OFF, the video
contents does not improve
normal.
Encoder is working normal.
27
28
The video
contents look
dark.
When AGC setting of encoder
change ON or OFF, the video
contents improve normal.
When AGC setting of encoder
change ON or OFF, the video
contents does not improve normal.
If this problem improves normal when changing
ON or OFF, the input or output signal is bigger
or smaller than the normal range.
Check the device connected.
Encoder is working normal.
The iris adjustment of the camera is possibly
necessary.
59
IP-900E/IP-900D series
Page 74
Chapter 5 Troubleshooting
No. Class Status Description Recommended action
29
30
31
Spoken words
cannot be heard on
the device
Has the receiving unit been
powered on?
Isn’t “None” selected in the audio
format setting of the encoder?
Are connections correct between
the receiving unit and speakers?
Check the power and operation of the
receiving unit.
Select an item other than “None” and set audio
to be encoded.
Check the connection between the receiving unit
and speakers.
32
33
34
35
36
37
38
39
40
41
42
Audio
Noise is generated
on the device.
The LINK/ACT
LED for the LAN
port is not turned
on.
Device setting
through a LAN is
disabled.
Network
The DEC LED is
blinking.
Is ALM LED turned on? Refer to clause 3 in this table.
Does noise disappear when
disconnecting LAN cable?
Does noise disappear when
disconnecting audio input cable
from the encoder?
Is packet loss occurring?
(Is DEC LED blinking?)
Is the power to the
communication destination device
turned on?
Are the LINK LEDs on this
device and the hub turned on?
Is the IP address specified from
the Web browser correct?
If not, this device is considered as abnormal.
If so, audio signal input to the encoder is
considered to be mixed with noise.
Check the audio output device.
Refer to clause 42 in this table.
Verify the power supply and operation of the
communication destination device.
If the LINK LEDs are not ON, the LAN cable is
not connected. Connect the LAN cable
correctly.
Specify a correct IP address from the Web
browser on the control terminal.
Make correct settings by referring to the PC
Are the network settings (IP
address, subnet mask, etc.) on the
control terminal PC correct?
user's guide and OS handbook. If this device
is started with the default settings made before
shipment from the factory, see "Section 3.3.1,
"Settings," for the network settings for the
control terminal PC.
If a reply is not received, turn on the power to
the device while holding down the MNT button
Is a reply received in response to
a PING command issued to the IP
address of the device?
to start the system with the default IP address
(10.0.0.1) set before shipment from the factory.
Confirm the IP address. If the problem
persists, check the status on the LAN. For
information on this startup procedure, see
Section 3.6, "Special Use of Cancel Key."
IP address mode setting is not proper.
After rebooting the device with the default IP
address set before shipment from the factory,
connect to the Web and confirm these alarm
codes.
・L009 DHCP connection failure
Make sure that DHCP-related setting and
Is ALM LED blinking?
DHCP server setting/operation of this device
are correct.
・L00A PPPoE connection failure
Make sure that PPPoE-related setting and
PPPeE server (carrier side) operation of this
device are correct.
For details, please refer to the Software User’s
Guide.
If so, confirm the followings.
Error is occurring in the received
stream data. Make sure that
connected network and the
encoder are set/operated correctly.
・Is system bit rate exceeding connected network
capacity?
・Are FEC/ARQ settings of this device and the
encoder correct?
・Are the network device and LAN port settings
(AUTO, Full/Half-duplex, etc) the same?
IP-900E/IP-900D series
60
Page 75
Chapter 5 Troubleshooting
5.2 Alarm LED Lamp Is On
5.2
This section describes corrective actions to take if an alarm LED turns on.
The appropriate corrective action depends on the alarm code displayed. See the table below for this
information.
Reference
See Section 3.3.2, “Log,” for information how to check the alarm log check and an
example with displayed information.
Table 5.2 Alarm codes and corrective actions
Code Corrective action
Lxxx Check the network and destination device. If an error cannot be identified, contact your
system administrator.
Exxx Turn off and on the device. If the device is still operating abnormally after being powered on
again, contact your maintenance personnel. Then, he/she may ask the alarm code.
Ixxx This indicates a loss of video input. Check the video output device and video cable connected
to the video input terminal.
xxx: Indicates a three-digit numeric value. See Section 3.3.2, “Log,” for more details.
In addition, LED display details are given in the following table:
Table 5.3 LED display details
Display Description
PWR Lights in green when the device is powered on.
Blinks in green in the operation preparation state, and lights in green in the operation state.
RDY
INDWN
ALM
Blinks in orange in the maintenance mode waiting state, and lights in orange in maintenance
mode.
No LED lights in normal state. Lights in orange in the state of audio/video input down or
abnormal.
Blinks in orange when the input signal slipping for encoder and the reference clock input down
for decoder.
Alarm LED. Blinks or lights in orange when a device alarm occurs.
For more details of the alarm log, see Section 3.2.2, “Log” and Section 3.2.7, “Log” of
IP-900E/IP-900D series Software User’s Guide.”
OPT Lights in green when the HD upgrade option is installed.
DEC
100M Turns on if the connected LAN is 100BASE.
LINK/ACT
Goes on in green during decoding. This LED stays off when decoding is not being
performed. It blinks in green when a decoding error occurs.
Indicates the LAN connection status and data send status.
It is lit when there is a LAN (HUB) connection, and off when there is no LAN connection.
It blinks when communication is in progress.
61
IP-900E/IP-900D series
Page 76
Chapter 5 Troubleshooting
5.3 Maintenance
5.3
5.3.1 Maintenance space
When the operators do the maintenance work, the maintenance space below is required in addition
to Section 2.1.4, “Open space required around the device.”
Desk-top installation:
Please allocate the space more than 1 m in front
or rear for maintenance.
Front space
for maintenance
>700mm×1000mm
Front access case
Rear space
for maintenance
>700mm×1000mm
Rear access case
Rack installation:
Please allocate the space more than 1 m in
front and rear for maintenance.
Front space
for maintenance
>700mm×1000mm
Rear space
for maintenance
>700mm×1000mm
IP-900E/IP-900D series
62
Page 77
Chapter 5 Troubleshooting
5.3.2 Change of maintenance parts (Maintenancer only)
If there is no improvement of situation after checking and dealing with referring Section 5.1,
“Help Information,” change the hardware following the procedure below.
The maintenance unit of this product is the whole equipment. When failure, please change
whole equipment for the change of the maintenance parts.
Please refer Section 2.6, “CF card insertion and removal,” for the respective maintenance.
63
IP-900E/IP-900D series
Page 78
(This page is intentionally left blank)
Page 79
Appendix
Appendix
The appendix contains view of the device and its main specifications. Notes on
installation work and preparations for on-site turn-up are also contained in this
section.
Figures described in this chapter are used IP-900Es’ as a sample.
A.1 Appearance·············································································· 67
A.2 Basic Specifications ································································· 69
A.3 Preparations for Installation Work ············································ 76
A.4 Preparations for On-site Turn-up·············································· 77
Page 80
(This page is intentionally left blank)
Page 81
A.1 Appearance
A.1
The appearance of IP-900E/IP-900D series is shown below.
100-240V
PWR ALM
FG
OPT
IN
RDY
DWN
MNT
Appendix
100M
LINK
/ACT
LR
300
PWR ALM
RDY
42
/ACT
OPT
LINK
IN
100M
DWN
210
67
IP-900E/IP-900D series
Page 82
Appendix
E136004
MADE IN JAPAN
1K91
I T E
FUJITSU LIMITED
00001
12345
08-10
01A
2.3kg
1φ
50/60Hz
100V-240V～
D08-0454001
T
認証番号
0.038kVA-0.048kVA
TA23742-B50X
0.38A-0.20A
PART NO.
IP-900E
MODEL
Bottom View
IP-900E/IP-900D series
68
Page 83
A.2 Basic Specifications
A.2
This chapter describes the external specifications, environment specifications, and function
specifications of the device.
A.2.1 External specifications
The device has the following external specifications:
Item Specifications
Installation conditions Indoor: Installation on a desk or in a rack that is mounted
Dimensions
Cooling method Forced air cooling (maintenance-free fan used)
Power 100-240VAC
Weight Max. 2.3 kg
Power consumption
Width: 210, Height: 42, Depth: 300 (mm) (excluding projections)
IP-900E :
IP-900D :
IP-900IID :
38 VA or less @ 100VAC
33 VA or less @ 100VAC
35 VA or less @ 100VAC
A.2.2 Environment specifications
The device has the following environmental specifications:
Item Specifications
Power conditions
Temperature and humidity
conditions
Dust
EMI
(Electro Magnetic
Interference - regulation)
100-240 VAC ± 10%, 50/60 Hz ± 3 Hz
Temperature: -10 to 55°C
(No low temperature startup: -10 to -1°C)
Humidity: 5 to 95% (without condensation)
(Conditions for guaranteed operation and characteristics)
Communication equipment room or office environment
(0.15 mg/m
FCC (part 15) Class A
EN55022 Class A
VCCI Class A
3
or less)
Appendix
IP-900E/IP-900D series
69
Page 84
Appendix
A.2.3 Function specifications
This chapter describes functional specifications of individual parts of the device.
(IP-900E only)
Name Specifications Remarks
Signal format: NRZI
Digital SDI
VIDEO input
Connector name SDI BNC
Pin number Signal name Remarks
1
2
Input impedance: 75Ω (Unbalanced)
Signal amplitude: 800mVp-p
Maximum amplitude level: 800mVp-p ± 10%
SIGNAL
SG
1
2
(IP-900E only)
Name Specifications Remarks
Signal format: NTSC (Analog composite, 29.97frames/s)
Analog
VIDEO
input
Connector
name
Pin number Signal name Remarks
1
2
PAL (Analog composite, 25frames/s)
Input impedance: 75Ω (Unbalanced)
Signal amplitude: 1.0 Vp-p
Maximum amplitude level: 0.5dB (0dB=100IRE)
Permissible cable length: 30m (3C-2T or equivalent)
ANALOG VIDEO OUT BNC
SIGNAL
SG
1
2
(IP-900IID only)
Name Specifications Remarks
Signal format: NRZI
Digital SDI
VIDEO output
Connector name SDI BNC
Pin number Signal name Remarks
1
2
Input impedance: 75Ω (Unbalanced)
Signal amplitude: 800mVp-p
Maximum amplitude level: 800mVp-p ± 10%
SIGNAL
SG
1
IP-900E/IP-900D series
70
2
Page 85
Appendix
(IP-900D / IP-900IID only)
Name Specifications Remarks
Signal format: NTSC (Analog composite, 29.97frames/s)
Analog
VIDEO
output
Connector
name
Pin number Signal name Remarks
1
2
PAL (Analog composite, 25frames/s)
Output impedance: 75Ω (Unbalanced)
Signal amplitude: 1.0 Vp-p
Maximum amplitude level: 0.5dB (0dB=100IRE)
Permissible cable length: 30m (3C-2T or equivalent)
ANALOG VIDEO OUT BNC
SIGNAL
SG
1
2
(IP-900E only)
Name Specifications Remarks
Analog
AUDIO
input
Connector
name
Connector
name
Analog voice signal(unbalanced)
Input impedance: 54kΩ
Input maximum level: +2Vrms
Permissible DC input level: ±5Vrms
ANALOG AUDIO IN (L) RCA
1
2
Signal name Remarks
SIGNAL
S G
ANALOG AUDIO IN (R) RCA
1
2
Signal name Remarks
SIGNAL
S G
1
2
1
2
(IP-900D / IP-900IID only)
Name Specifications Remarks
Analog
AUDIO
output
Connector
name
Connector
name
Analog voice signal(unbalanced)
Output impedance: 1kΩ
Output maximum level: +2Vrms
ANALOG AUDIO OUT (L) RCA
1
2
Signal name Remarks
SIGNAL
ANALOG AUDIO OUT (R) RCA
1
2
Signal name Remarks
SIGNAL
S G
S G
1
1
2
2
IP-900E/IP-900D series
71
Page 86
Appendix
g
Name Specifications Remarks
[10BASE-T]
System standard: IEEE802.3
Transmission clock: 10Mbit/s±10000ppm(±0.01%)
Load impedance: 100Ω
LAN interface
Transmission coding: Manchester coding
[100BASE-TX]
System standard: IEEE802.3u
Transmission clock: 125 Mbit/s±5000ppm(±0.005%)
Load impedance: 100Ω
Transmission codin
: 4B5B
Connector name 10/100 BASE RJ-45
Pin number Signal name Remarks
1
2
3
4
5
6
7
8
Cable
TD+
TDRD+
N.C.
N.C.
RDN.C.
N.C.
Standard: ANSI/TIA/EIA568A CAT5
Pin assignment: Comply with one of two below
Pin No. 1 2 3 4 5 6 7 8
T568A W/G G W/O Bl W/Bl O W/Br Br
T568B W/O O W/G Bl W/Bl G W/Br Br
[W: white, G: green, O: orange, Bl: blue, Br: brown]
Trans. data+
Trans. data-
Reciv. data+
-
-
Reciv. data-
-
-
8 7 6 5 4 3 2 1
IP-900E/IP-900D series
72
Page 87
Appendix
Name Specifications Remarks
No. of CH
Signal system
Data interface
(RS-232C)
Connector name RS-232C D-sub 9 pin(male)
Pin number Signal name Remarks
1
2
3
4
5
6
7
8
9
Connection
Bit rate
Data length
Parity
Stop bit
CD
RD
SD
DTR (ER)
SG
DSR (DR)
RTR (RS)
CTS (CS)
RI
: 1 ch
: Asynchronous
: DTE
: 1200, 2400, 4800，9600, 19200, 38400 bps
:7/ 8
: NONE/ODD/EVEN
: 1/2
Carrier Detect
Receive Data
Send Data
Data Terminal Ready
Signal Ground
Data set Ready
Request to Send
Clear to Send
Ring Indicator
①⑤
RS-232C
⑥
Name Specifications Remarks
Parallel 2 pin with ground
POWER
Input voltage
Connector
Button
Input protection
Withstand voltage
: 100-240VAC±10%
: Inlet
: Locker button
: Built-in fuse
: 1,500 VAC
⑨
Connector name 100-240V
Pin number Signal name Remarks
1
2
3
L1
L2
FG
3
1
FG
L1 L2
2
IP-900E/IP-900D series
73
Page 88
Appendix
(IP-900E only)
Name Specifications Remarks
Signal format
HDMI input
Input impedance
Maximum length
connector
Connector name
HDMI IN HDMI 19 pin Type A
Pin number Signal name Remarks
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
TMDS DATA2 +
TMDS DATA2 SHIELD
TMDS DATA2 TMDS DATA1 +
TMDS DATA1 SHIELD
TMDS DATA1 TMDS DATA0 +
TMDS DATA0 SHIELD
TMDS DATA0 TMDS CLOCK +
TMDS CLOCK SHIELD
TMDS CLOCK CEC
RESERVE(N.C)
SCL
SDA
DDC/CEC GROUND
+5V POWER
HOT PLUG DETECT
：TMDS
：50 ohms ±10%
：-------：19PIN Type A
Length of the attested HDMI cable
is pretermission.
The unattested cable can't be used.
(IP-900D /IP-900IID only)
Name Specifications Remarks
HDMI output
Connector name
Signal format
Input impedance
Maximum length
connector
HDMI OUT HDMI 19 pin Type A
：TMDS
：50 ohms ±10%
：-------：19PIN Type A
Pin number Signal name Remarks
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
TMDS DATA2 +
TMDS DATA2 SHIELD
TMDS DATA2 TMDS DATA1 +
TMDS DATA1 SHIELD
TMDS DATA1 TMDS DATA0 +
TMDS DATA0 SHIELD
TMDS DATA0 TMDS CLOCK +
TMDS CLOCK SHIELD
TMDS CLOCK CEC
RESERVE(N.C)
SCL
SDA
DDC/CEC GROUND
+5V POWER
HOT PLUG DETECT
Length of the attested HDMI cable
is pretermission.
The unattested cable can't be used.
IP-900E/IP-900D series
74
Page 89
Appendix
LED name ON Blinking OFF Remarks
PWR G Power ON --- Power OFF
G Normal operation Starting up RDY
O
Maintenance mode
LAN
(IP=10.0.0.1,
Subnet=255.0.0.0)
ALM O Equipment alarm FAN alarm
IN DWN
(IP900E only)
LINK/ACT
[LAN]
100M G 100BASE operation --- 10BASE operation
OPT
(IP-900E only)
DEC
(IP-900D/
IP-900IID only)
O Video input
down/fault
G LINK established LAN packets detection Cable disconnection
G HD-option installed --- HD-option not
G Decoding stream Packet loss Not decoding
Maintenance mode
starting up
Temperature alarm
CF card access error
IP address acquisition
failure
Reference clock slipping
Reference clock input
down/fault
Software inactive Blink interval: 0.5s
Maintenance mode
(Cancel button
startup):
LAN subnet mask
(255.0.0.0)
Normal operation
Normal operation HD-SDI video
input or reference
clock input
monitoring
or software inactive
installed
stream
G: Green, O: Orange
Name Button type Specifications Behavior
POWER Locker button Power ON/OFF
75
IP-900E/IP-900D series
Page 90
Appendix
A.3 Preparations for Installation Work
A.3
This section contains notes and describes check items for installation work.
A.3.1 Scope of installation work
For details about the scope of installation work, see Section 4.1, “Installation Preparations.”
A.3.2 Unpacking and device check
Unpack and check the device as follows:
• During unpacking, carefully handle the device so as not to apply shock to it or damage its
appearance.
• Make sure that the device and accompanying package are not damaged.
• Make sure that wiring does not have a short circuit and is not disconnected.
• Make sure that no incorrect screw is contained in the package.
A.3.3 Installation conditions
For the classification of this work, see Section 2.1, “Installation Conditions.”
The installation method may differ depending on the site where the device is installed. In
principle, the installation method conforms to the appropriate method for the site.
Do not install the device at the following locations:
• Place exposed to direct sunlight or near a heater.
• Humid or dusty place
• Place where the device is exposed to shock or vibration
• Unstable place, such as on a slope or place with a lot of weight on it
• Place where the device is subject to strong magnetic and radio waves
A.3.4 Connecting external cables
Refer to Chapter 2, “Installation and Connection,” for the connection methods, Section 4.2,
“Cables and Connector Details,” and A.2.3, “Function specifications,” for device connector pin
assignments.
IP-900E/IP-900D series
76
Page 91
A.4 Preparations for On-site
A.4
Turn-up
This chapter explains the workflow of on-site turn-up.
START
START
準備
Preparations
環境確認
Environment check
Visual check of
員数確認
外観目視確認
appearance
ケーブル接
Cable connection
版数確認
check
続
Input voltage check
入力電圧確認
Appendix
Power on
電源投入
Unit test
単体試験
System test
システム試験
ＥＮ
END
Ｄ
Since system configurations of the device are diverse depending on the applications used, this chapter
describes the checking process for only a single device.
77
IP-900E/IP-900D series
Page 92
Appendix
(1) Preparations
1) Check the system configuration
Check the entire system configuration.
2) Check the units and cables to be connected to the device
Check the units to be connected to the device, cables that have to be procured, and
installation conditions.
3) Tools and measuring instruments necessary for work:
• Digital multimeter
• General-purpose tools
(2) Environment check
1) Ambient air temperature, humidity and power supply
Make sure that the ambient air temperature, the humidity and power supply conform to
A.2.2, “Environment Specifications.
2) Ground connection (FG)
Make sure that use a grounding resistance of 100 ohms, a wire of 2mm
your country’s applicable standard.
(3) Visual check of appearance
1) Make sure that the device surface has no damage such as scratches, dirt, rust,
deformation or peeling of its coating.
2) Make sure that patent nameplate and device nameplate are still attached, and that
buttons are not damaged.
3) Make sure that connectors are not loose.
2
or thicker, or
(4) Cable connection check
Make sure that individual cables are connected as prescribed in system specifications.
Refer to Chapter 2, “Installation and Connection,” for the connection methods, Section 4.2,
“Cables and Connector Details,” and A.2.3, “Function specifications,” for device connector
pin assignments.
Hardware settings need not be set in the device.
(5) Input voltage check
Make sure that the voltage of power supplied to the device is in a range of 100-240 VAC
± 10%.
IP-900E/IP-900D series
78
Page 93
(6) Power on
(7) Unit test
(8) System test
Appendix
1) Set Power button on the front panel to [ON].
2) Make sure that that PWR LED lamp on the front panel is on.
1) Since this device executes a self-check immediately after power is turned on, make
sure that the RDY LED
on the front of the panel does not light after power is turned
on.
2) The LEDs light if the self-check detects an unusual condition.
1) Software installation
Install appropriate software following IP-900E/IP-900D series Software User’s Guide.
2) Set-up check
Various devices settings complying with the system specification are made from the
control terminal either directly or via the network.
3) Input video check
Make sure that the video input to the device is correctly output to the monitor
(television).
4) Data communication check
Make sure that the line used by the system is connected.
Status check
5)
After the final setup, when the equipment is in the system operation state, make sure
that the device status LED (RDY) on the front of the device lights in green, and that the
alarm LED (ALM) is off.
79
IP-900E/IP-900D series
Page 94
(This page is intentionally left blank)
Page 95
Glossary and Index
Glossary and Index
Glossary ····························································································· 83
Index··································································································· 86
CE Conformity Information ································································· 88
Page 96
(This page is intentionally left blank)
Page 97
Glossary and Index
Glossary
Alarm Log
Record of errors that have occurred on devices
and communication lines
BNC (Bayonet Neill Concelman)
Type of coaxial connector whose characteristic
impedance is 75
bayonet lock is used, ensuring cables are easy
to connect and remove, and secure connections.
The connector is compact and lightweight and
has a frequency range compatible with the high
frequency of 4 GHz, so it can be used for
measuring instruments and digital audio
equipment.
Ω. A locking system called a
Browser
General name for programs that support users
who want to select desired options from
available options. Using a browser, a user can
trace links on the Internet to access such
multimedia information as text, audio, and video
by simply using a pointing device (e.g., mouse)
to select items.
DCE (Data Circuit terminating Equipment)
Data circuit terminating equipment. DCE is a
term from ITU-T. Similar to modems and DSUs,
it changes signals to waveform that are suitable
for their transmission routes.
DHCP (Dynamic Host Configuration Protocol)
This is the protocol to assign IP address
dynamically when startup and to release it when
shutdown. The IP address prepared by DHCP
server is assigned.
DTE (Data Terminating Equipment)
Data terminating equipment. It is one kind of
terminal equipment (e.g., PC). DTE is a term
from ITU-T and is paired with DCE.
Embedded Audio
It is the scheme to embed (multiplex)
AES/EBU digital audio signals in the auxiliary
data area (blanking area) of the serial digital
signal.
FG (Frame Ground)
Ground for a cabinet
Flow Control
Procedure for controlling the flow of data
between two devices. Its purpose is to prevent
data loss when the device buffer becomes full.
Gateway
Equipment that connects network systems that
use different protocols. It basically converts
one protocol into another to support operation
between two networks. In a broader sense, a
gateway sometimes means a device that
transfers information between any two networks.
HD-SDI (High Definition television – Serial
Digital Interface)
HD-SDI is the serial digital interface to
transmit HD (High Definition) video signal,
which transmission rate is 1.485 Gbps. It can
transmit multiplexing HD video signal, PCM
audio signal and data signal like time stamp.
HTTP (Hyper Text Transfer Protocol)
Protocol used for sending and receiving files
and other data between a WWW server and
WWW browser
Hub
Concentrator required for using 10BASE-T or
100BASE-TX as a local area network (LAN)
standard. Twisted-pair cables are used to
connect hubs. A high-speed hub conforms to
100BASE-TX, and a switching hub has switching
functions.
IP (Internet Protocol)
Protocol used between host computers to
transfer packets over all of the Internet. The
codes that identify the destinations and senders
in packet transfers are called IP addresses. An
IP address is a 32-bit code that can identify a
network and host in the network. A unique IP
address must be allocated to each hosts that
communicates on the Internet.
IP Address
Code used for identifying a node (e.g., PC)
operating using TCP/IP. This 32-bit number is
divided into four 8-bit sections, and an example
of this is 200.10.101.1.
83
IP-900E/IP-900D series
Page 98
Glossary and Index
IP Multicast
Technology for transmitting identical data to
multiple remote destinations simultaneously using TCP/IP. An address system called class D
is used for multicasting. In the class D address
system, the first four bits (1110) indicate a multicast, and the remaining 28 bits specify a
multicast group. Path control methods for IP
multicasting are PIM and DVMRP, but no one
method has become the standard yet.
LAN (Local Area Network)
Data communication system in a specific area
(maximum of 6 miles or about 10 km). It
provides moderate to high data transfer speeds.
LCD (Liquid Crystal Display)
The display device using the liquid crystal. A
LCD is a thin, flat display device made up of any
number of color or monochrome pixels arrayed
in front of a light source or reflector. There are
two categories, the simple matrix like STN and
DSTN and the active matrix like TFT.
LED (Light-Emitting Diode)
The IP-900E/IP-900D series has a power
LED lamp and alarm LED lamps. The power
LED lamp is lit in green to indicate the device
is on. An alarm LED lamp is lit in red to
indicate that an alarm has been generated.
MPEG-4
Standard for the compression and coding
of color video for storage purposes, and the
name of the organization promoting this
standardization is used in the name of the
standard. MPEG-4 handles not only regular
image and voice data but also a comprehensive
range of multimedia data, including computer
graphics and text. It defines a flexible
framework for a scalable object encoding system
depending on technological developments. It
has a transfer speed ranging from several tens
of Kbps to several tens of Mbps (low bit rate
to wide range). It is intended for low-speed
communication by general-purpose multimedia
encoding systems on mobile terminals.
PING
Command supported by operating systems such
as UNIX, Windows 9x, and Windows NT, and it is
used in TCP/IP networks to check whether IP
packets can reach or have reached their
communication destinations
connection like PPP connection on the Ethernet
network.
PS
MPEG-2 method of multiplexing audio, video,
and data. It is an abbreviation of Program
Stream, and it is used for transmission and
storage in an error-free environment.
RS-232C
Interface standard that was mainly established by
the Electronics Industry Association (EIA) for
communication between data terminals and data
communications equipment
SD-SDI (Standard Definition television – Serial
Digital Interface)
Standard definition digital video interface
standardized in SMPTE259M.
SG (Signal Ground)
Ground for signals
Subnet Mask
Mask value used for obtaining a subnet network
address from an IP address. The subnet
address is obtained by using an AND operation
between an IP address and subnet mask.
TCP (Transmission Control Protocol)
Abbreviation of Transmission Control Protocol,
which is the protocol required for direct connection
to the Internet. In the OSI reference model, TCP
corresponds to the transport layer and IP
corresponds to the network layer. TCP has been
a global standard protocol that is supported by
major operating systems, including UNIX, OS/2,
Windows 95, and Windows NT.
TS (Transport Stream)
The stream used in the multi-programs
multiplexing, standardized in MPEG-2 systems.
The transport stream offers features for error
correction for transportation over unreliable media,
and is used in broadcast applications and ATM
telecommunication.
TTL (Time To Live)
Abbreviation of time to live, which indicates the
survival time of a packet in a network. If a packet
sent to a network happens to enter a loop because
of a setting error on a router, it will not survive
forever but will be discarded when the time
specified in the Time To Live field of the IP header
is reached.
PPPoE (Point to Point Protocol over Ethernet)
This is the user authentication standard for the
IP-900E/IP-900D series
84
Page 99
UDP (User Datagram Protocol)
Abbreviation of User Datagram Protocol, which is
a TCP/IP transaction protocol used for specific
applications such as remote network management
and naming service access
Unicast
Communication with a station at a single address
(i.e., most general one-to-one communication)
UTP Cable
Abbreviation of unshielded twisted pair. It is a
unshielded pair of wires twisted together, and
these wires are used for Ethernet cabling and
other purposes.
10BASE-T
LAN that uses unshielded twisted-pair (UTP)
cables and complies with the IEEE 802.3
standard. A 10BASE-T connection uses a
concentrator called a hub. It is widely used
because special cabling work is not necessary
and wiring can be done easily. The maximum
length of cable wiring is 100 m.
Glossary and Index
100BASE-TX
One of the 100BASE LAN standards (also
called Fast Ethernet), it supports a transfer rate
of 100 Mbps. Other 100BASE standards are
10BASE-T4 and 100BASE-FX, and the difference is the type of cable used. 100BASE-TX
uses unshielded twisted-pair (UTP) cables. It
also uses the RJ-45 connector, which is similar
to the modular jacks used for telephones.
85
IP-900E/IP-900D series
Page 100
Glossary and Index
Index
１
1000BASE-T ................................................. 3, 29
100-240VAC .................................... 3, 26, 69, 73
100-240VAC power cord .................................. 50
100BASE-TX ......................................... 3, 29, 72
10BASE-T .............................................. 3, 29, 72
Ａ
Alarm LED ..................................................... 6, 8
Alarm LED lamp .............................................. 61
Appearance......................................................... 67
Appendix ............................................................65
Audio and video device connections .............. 27
Audio input................................................ 3, 7, 8
Audio output........................................................ 3
AV input status LED.......................................... 6
Ｂ
Basic application examples ................................ 5
Basic specifications ........................................... 69
BNC............................................................. 28, 45
Ｅ
Environment specifications................................69
External specifications....................................... 69
Ｆ
FG terminal..................................................... 7, 8
Function specifications ...................................... 70
Ｇ
Glossary .............................................................. 83
Glossary and Index ...........................................81
Ｈ
HDMI...................................................... 3, 27, 28
HDMI cable ....................................................... 47
HDMI input ....................................................... 74
HDMI output ..................................................... 74
HD-SDI............................................................ 7, 9
Help Information ...............................................55
Humidity........................................................3, 69
Ｃ
Cable and connector details............................. 45
Cable Specifications .......................................... 41
CF card .............................................................. 31
CF Card Insertion and Removal ..................... 31
CF CARD slot ............................................... 3, 7
Change of maintenance parts........................... 63
Components..........................................................4
Connecting external cables............................... 76
Connection to an RS-232C device.................. 30
Connection to network...................................... 29
Connection to power source ............................ 24
Cooling method ................................................. 69
Cooling system .................................................... 3
Ｄ
Data input/output ................................................. 3
Data interface..................................................... 73
Device settings and operation.......................... 36
Dimensions.................................................... 3, 69
Dust .................................................................... 69
Ｉ
Index ................................................................... 86
Installation and Connection .............................. 11
Installation conditions..................... 3, 13, 69, 76
Installation preparations.....................................43
IP address...................................... 38, 40, 57, 60
Ｌ
LAN cable.......................................................... 49
LAN interface .................................................... 72
Ｍ
Main features ....................................................... 3
Maintenance space............................................. 62
IP-900E/IP-900D series
86
Loading...