Fujitsu F022 User Manual

Hyo1.fm 0 ページ 2011年1月7日 金曜日 午前11時26分
FUJITSU F-022 User Guide
F-022_E2kou
F-022.book 0 ページ 2011年2月24日 木曜日 午後2時42分
FUJITSU WCDMA/HSDPA (3G (WCDMA)) 850/2100,
GSM/GPRS/EDGE (2G) 900/1800/1900 System
Thank you for purchasing FUJITSU mobile terminal.
Before using your terminal
Some of the services described in this manual may not be supported by all networks. Please contact your network opera tor to confirm whether you can use or not a particular service.
Your phone supports emergency numbers, such as 110, which allow to make emergency calls with or without a SIM/USIM card inserted, if a 3G (WCDMA) or GSM network is within range. However emergency calls may not be possible on all mobile phone networks, or when certain network services or phone features are in use. You should therefore never rely solely upon any mobile phone for essential communications, such as medical emergencies.
Because your terminal uses wireless transmission, it may not function in locations where it is difficult for radio waves to penetrate, such as tunnels, underground passages and some buildings, in areas where radio wave signals are weak, or out of service area. Even when you are high up in a tall building or condominium and nothing blocks your view outside, your terminal may not be able to receive or transmit signals. Also, communication may be interrupted even when the signal meter on your terminal indicates there is a strong signal.
Your terminal encodes voice communication as digital data. When you are operating your terminal while moving to a location subject to weaker radio wave signals, the transmitted digital data may not be correctly decoded and as a result the decoded voice may differ somewhat from the actual voice.
Use your terminal in a way that does not disturb others in public spaces, crowded locations or quiet places.
Maintain a separate record of the data (Phonebook, Schedule, Notepad, Saved messages, Voice memos, Movie Files, etc.) you registered in your terminal. You are recommended to save important data to microSD/microSDHC card (If you have none, purchase it in Electronic stores). Using Mobile data link tool contained in F-022 CD-ROM, you can also transfer and save phonebook and some other data to a PC. Note that we assume no responsibility for any loss of saved contents or data resulting from malfunction, repair, changing of the model or other handling of the F-022 terminal. In addition, FUJITSU assumes no responsibility for third­party applications and for contents or data downloaded from the network.
The user hereby agrees that the user shall be solely responsible for the result of the use of SSL/TLS. Neither FUJITSU nor the certifier as listed herein makes any representation and warranty as for the security in the use of SSL/TLS and any damage that may result from the use of SSL/TLS. Unauthorized copying of parts of or this entire manual is prohibited. The images or illustrations provided in this manual are for information purposes only and may differ from the actual displays. The contents of this manual and product specifications are subject to change without prior notice.
F-022_E2kou
F-022.book 1 ページ 2011年2月24日 木曜日 午後2時42分
Contents
Chapter 1 Introduction ...........3
1.1 Use the Fragrance rear cover ............. 3
1.2 Waterproofness/Dustproofness .........4
1.3 Use the open assist button.................9
1.4 Precautions (ALWAYS FOLLOW
THESE DIRECTIONS) ........................ 10
1.5 Handling precautions........................ 15
Chapter 2 Get started ...........19
2.1 Keys and parts................................... 19
2.2 Attach SIM/USIM/battery.................. 21
2.3 Use microSD card .............................22
2.4 Use earphone .................................... 22
2.5 Use desktop holder and AC adapter in
combination for charging................. 23
2.6 Charge using AC adapter ................. 23
2.7 Attach the wrist strap........................ 24
2.8 Switch the mobile terminal on or off
................................................................
2.9 Interactive standby mode elements ....
2.10 Write text .........................................25
2.11 Display indicators............................ 27
2.12 Search in your mobile terminal .....27
2.13 Change the volume of a call, song, or
video................................................. 27
2.14 Use your mobile terminal offline...28
2.15 Prolong battery life ......................... 28
24 25
Chapter 3 Personalisation.... 29
3.1 Profiles ............................................... 29
3.2 Change your theme .......................... 29
3.3 Home screen ..................................... 30
3.4 Light alert........................................... 31
Chapter 4 Telephone ............ 32
4.1 Call a phone number ........................ 32
4.2 Call a contact ..................................... 32
4.3 Voice clear and Voice slowing .........32
4.4 Make a video call .............................. 33
4.5 Make a conference call ..................... 33
4.6 Use speed dial................................... 34
4.7 Call the last dialled number ............. 34
4.8 Record a phone conversation .......... 34
4.9 Turn to silence................................... 35
4.10 View your missed calls................... 35
4.11 Call your voice mailbox .................. 36
4.12 Divert calls to your voice mailbox or
another phone number................... 36
4.13 Prevent making or receiving calls
.................................................................. 36
4.14 Allow calls only to certain numbers
.................................................................. 37
Chapter 5 Contacts............... 38
5.1 Save phone numbers and mail
addresses .......................................... 38
5.2 Save a number from a received call or
message ............................................ 38
5.3 Contact your most important people
quickly................................................ 39
5.4 Set a ringing tone for a specific contact
.................................................................. 39
5.5 Send your contact information using
My Card ............................................. 40
5.6 Create a contact group ..................... 40
5.7 Send a message to a group of people
.................................................................. 40
5.8 Contacts stored on the SIM card ..... 40
Chapter 6 Messaging............ 41
6.1 Send a message................................ 41
6.2 Send an audio message ................... 41
6.3 Receive messages............................. 41
6.4 Change language .............................. 42
Contents
1
F-022_E2kou
F-022.book 2 ページ 2011年2月24日 木曜日 午後2時42分
Chapter 7 Mail ......................43
7.1 Mail .................................................... 43
7.2 Open mail from the home screen.... 43
Chapter 8 Internet.................44
8.1 Browse the web................................. 44
8.2 Add a bookmark ................................ 44
8.3 Subscribe to a web feed ................... 44
Chapter 9 Camera .................45
9.1 Take a picture .................................... 45
9.2 Take a picture with smooth skin and
enhanced eyes .................................. 45
9.3 Take a picture in the dark .................45
9.4 Take a picture of a moving object ...45
9.5 Picture tips ......................................... 46
9.6 Record a video................................... 46
9.7 Send a picture ................................... 46
Chapter 10 Your pictures and
videos......................................47
10.1 View pictures and videos ............... 47
Chapter 11 Videos ................48
11.1 Play a video ..................................... 48
Chapter 12 Music and audio 49
12.1 Music player .................................... 49
12.2 Record sounds ................................ 50
Chapter 13 Time management
............................................... 51
13.1 Clock................................................. 51
13.2 Calendar........................................... 52
Chapter 14 Office................. 55
14.1 Make a calculation .......................... 55
14.2 Write notes ...................................... 55
Chapter 15 Useful tools ....... 56
15.1 Pedometer ....................................... 56
15.2 Mirror ............................................... 57
Chapter 16 Connectivity ...... 58
16.1 Connection safety ........................... 58
16.2 Bluetooth ......................................... 58
16.3 Close a network connection ........... 60
16.4 Store your files on a remote drive
.................................................................. 61
Chapter 17 Mobile terminal
management........................... 62
17.1 Manage files .................................... 62
17.2 Increase available memory for more
content ............................................. 62
17.3 Manage applications ...................... 62
17.4 Synchronise content....................... 63
17.5 Protect your mobile terminal ......... 63
Chapter 18 Access codes ..... 65
Chapter 19 Q & A ................. 66
Chapter 20 Appendix............ 68
20.1 SAR and Certification Information
.................................................................. 68
20.2 Export Administration Regulations
.................................................................. 70
20.3 Intellectual Property Right.............. 71
20.4 End User License Agreement ........71
20.5 F-022 package.................................. 72
20.6 China RoHS Instruction .................. 73
20.7 Limited warranty............................. 73
20.8 Trademarks...................................... 75
Index ....................................... 76
Contents
2
F-022_E2kou
F-022.book 3 ページ 2011年2月24日 木曜日 午後2時42分
Chapter 1 Introduction
1.1 Use the Fragrance rear cover
You can use F-022 terminal with your favorite aroma. Put perfume on in the following steps.
Use perfume only.
Check precautions about the perfume before putting it on the fragrance chip.
In the instruction below, the Fragrance rear cover has been installed. You can install the Fragrance rear cover in the same way as the rear cover.
Move the fragrance piece by raising its tab in the direction of
1
the arrow.
Tab
Put perfume on the fragrance chip on the rear side of the
2
fragrance piece.
Fragrance chip
Fragrance piece
Wipe off perfume on the area other than the fragrance chip.
3
Turn the rear side of the fragrance piece down, align either tab
4
with the groove on the rear cover, and then push the piece into the cover.
Groove
Maintenance
Wash the Fragrance rear cover and piece with running water, wipe them with a dry cloth, and then dry them naturally.
• To keep the Fragrance rear cover clean, do not leave the cover with perfume uncared; be sure to maintain it on a regular basis.
• When changing the aroma, maintain it in the same way. After washing the fragrance piece, the aroma gets weak, but is not removed completely.
Tab
Rear side
Rear side
3
F-022_E2kou
F-022.book 4 ページ 2011年2月24日 木曜日 午後2時42分
Important precautions
• Be sure to remove the fragrance piece and put perfume on the chip on rear side of the piece. Putting perfume on directly without removing the fragrance piece causes discoloration or deformation.
• Be careful of the amount of perfume that you put on the fragrance chip. Wipe perfume on the area other than the fragrance chip immediately.
• Do not put strong impact on the fragrance piece or apply excessive it when installing it.
• Some types of perfume may discolor the Fragrance rear cover or peel the paint off. When discoloration occurs or the paint is peeled off, stop using the perfume immediately.
• The strength or duration of aroma varies by the type or amount of perfume.
• Do not remove the fragrance chip. If the chip is removed, check where the cuts on the chip are and then put the chip into the fragrance piece in the direction of the arrow before using.
1.2 Waterproofness/Dustproofness
F-022 is provided with the following waterproofness by firmly closing the external connection jack cap, installing the rear cover and locking the cover.
1
IPX5*
IPX8*3 that is a higher standard than IPX7* Also, F-022 is dustproof to IP5X*4 if the external connection jack cap is strictly closed as well as the rear cover is mounted and locked.
*1 Code IPX5 means that a phone keeps functioning after directly
applying a jet flow of 12.5 L/min. for at least 3 minutes from a distance of 2.5-3 m on a rotating turntable.
*2 Code IPX7 means that a phone keeps functioning after it is slowly
submerged to depth of 1 m in static tap water at room temperature, left there for 30 minutes and then taken out.
*3 Code IPX8 means that it provides waterproofness of which exceeds
of IPX7 standard.
2
Chapter 1 Introduction
4
F-022_E2kou
F-022.book 5 ページ 2011年2月24日 木曜日 午後2時42分
*4 Code IP5X means that a device is protected against the ingress of
dust specific to dustproof test (25 µm or smaller in diameter), so that the ingress will not interfere with predefined operation and safety of the device.
F-022 provides the following waterproof performances of IPX8.
• F-022 keeps functioning after it is slowly submerged to depth of 1.5m in static tap water at room temperature, left there for 30 minutes and then taken out.
• The mobile phone keeps shooting still images or moving pictures in 30 minutes in static tap water at room temperature.
What you can do with waterproofness and dustproofness of F-022
You can talk without using an umbrella in the rain (for rainfall of 20 mm or less per hour).
- When your hands or F-022 terminal are wet, avoid installing/
removing the rear cover or opening/closing the external connection jack cap.
You can also shoot still images and moving pictures in the pool depth of 1.5 m.
- Do not perform other operations underwater than shooting still
images and moving pictures.
- If you put the terminal in water of swimming pool, be sure to
have it within 30 minutes.
- If F-022 terminal gets wet with water from the swimming pool,
wash it as predefined.
You can use F-022 terminal in a bathroom.
- Do not put the terminal in the bathtub. Do not use the terminal
in hot water. Doing so may cause malfunction.
- Never put F-022 terminal in hot spring water or water containing
soap, detergent or bath powder.
To ensure waterproofness/dustproofness
To avoid water and dust ingress, be sure to observe the following points.
Do not throw any liquid other than room-temperature tap water on F-022 terminal, or soak it in such liquid.
Open/close the external connection jack cap as described below.
<Opening the external connection jack cap>
Place your finger at groove on the hinge side to open the cap.
Groove on the hinge side
<Closing the external connection jack cap>
Close with the tab for the rear cover at the rear side of the cap fitted into the concave of this terminal. Make sure that the cap is completely closed without slack.
Tab on the rear cover side
Install the rear cover as described below.
Chapter 1 Introduction
5
F-022_E2kou
F-022.book 6 ページ 2011年2月24日 木曜日 午後2時42分
<Installing the rear cover>
Align 8 tabs of the rear cover with concaves of F-022 terminal. While pressing the rear cover in the direction of
a
so that there is no gap between F-022 terminal and rear cover, slide the rear cover in the direction of direction of
b
to install, then slide the rear cover lever in the
c
to lock.
* Make sure that the rear cover is completely closed without slack.
Slide the rear cover in the direction of the arrow shown on the lever, and then make sure the cover is securely locked before using.
Back cover
Lever
Securely lock the rear cover and firmly close the external connection jack cap. Even a fine obstacle (one hair, one grain of sand, tiny fiber, etc.) put between contact surfaces may allow water to enter.
Do not poke the microphone, earpiece or speaker with a swab or sharp object.
Do not let F-022 terminal fall. It may become scratched causing the waterproof/dustproof performance to degrade.
The external connection jack cap and the rubber packing of the inner lid play an important role for keeping waterproof/dustproof performance. Do not remove or scratch it. Also, prevent dust from adhering to it.
Important precautions
Do not perform actions shown in the illustrations below.
<Example>
Using soap/detergent/
bath powder
Applying strong
water flow
Washing with brush/sponge
Using in
hot spring
Washing by
laundry machine
Soaking in
ocean water
Observe the following precautions to use F-022 terminal properly.
Accessories and optional devices are not waterproof/dustproof. When watching moving pictures etc. with F-022 terminal installed in the desktop holder, do not use it in a bath room, shower room, kitchen or lavatory even if it is not connected to the AC adapter.
Do not apply water flow stronger than allowed (e.g., such water flow that gives you pain when applied to your skin directly from a faucet or shower).
If F-022 terminal should get wet with salt water, seawater, soft drink or with mud or soil, flush away immediately. When it dries out, it becomes harder to get rid of, causing scratch or malfunction.
Chapter 1 Introduction
6
F-022_E2kou
F-022.book 7 ページ 2011年2月24日 木曜日 午後2時42分
Do not put F-022 terminal in hot water, use it in a sauna or apply hot airflow (from a hair dryer etc.) to it.
Do not move in water or slam the terminal against the surface of water with F-022 terminal opened.
If you put the terminal in tap water or in water of swimming pool, be sure to have it within 30 minutes.
When you use the terminal in swimming pool, obey rules of the facility.
F-022 terminal does not float on water.
Do not leave water on F-022 terminal. May short-circuit the power jacks, or in a cold region, water may freeze causing malfunction.
Do not leave water on the microphone, earpiece or speaker. Such water may interfere with talking.
If the rear cover is damaged, replace it. Water may enter inside from a damaged section causing troubles such as electric shocks or corrosion of the battery.
If F-022 terminal gets wet with water or other liquids with the external connection jack cap or rear cover open, the liquid may get inside the terminal causing electric shocks or malfunction. Stop using F-022 terminal, turn the power OFF, remove the battery and contact a D-PHONE-specified repair office.
If rubber gasket on the external connection jack cap or inner lid is damaged or deformed, replace it at D-PHONE-specified repair office. FUJITSU does not guarantee actual operations under all states. Malfunctions deemed to be caused by inappropriate operation by the customer are not covered by the warranty.
Wash F-022 terminal
Wash the terminal with tap water while holding the external connection cap. Do not rub the terminal.
Press here
Do not apply water flow stronger than allowed (e.g., such water flow that gives you pain when applied to your skin directly from a faucet or shower).
Wash it using room-temperature tap water with your hand, the rear cover of F-022 terminal installed and locked, and the external connection jack cap held in position.
Do not use any brush, sponge, soap, cleaning material, etc.
When mud or soil is attached to F-022 terminal, do not open or close the terminal. Instead, rinse the terminal clean by shaking it several times in tap water in a bucket and then flush away with running water.
After flushing away, wipe off water with a dry cloth, drain, and dry naturally as described below.
Chapter 1 Introduction
7
F-022_E2kou
F-022.book 8 ページ 2011年2月24日 木曜日 午後2時42分
Drain the water from F-022 terminal
When F-022 terminal is wet, water may flow out after wiping it off; drain the water in the following steps.
a
Wipe F-022 terminal surface with dry, clean cloth etc.
b
Shake F-022 terminal approximately 20 times, firmly holding its
hinge section, until there is no more water splattering.
To drain water off the speaker, shake F-022 terminal with the speaker upward
c
Softly press dry, clean cloth etc., against F-022 terminal to wipe off water remaining in the microphone, earpiece, speaker, keys, hinges or charging jack.
d
Remove the rear cover and wipe off any drops of water around the inner lid and the rear side of the rear cover. Never open the inner lid. After wiping off the water, install and lock the rear cover.
Around the inner lid
Chapter 1 Introduction
8
Rear side of the rear cover
F-022_E2kou
F-022.book 9 ページ 2011年2月24日 木曜日 午後2時42分
e
Wipe off water drained from F-022 terminal with dry, clean cloth etc, and dry naturally.
Water, if any, remaining in F-022 terminal may ooze up after wiping off.
Do not wipe off water remaining in concaves directly with a cotton swab etc.
Charge
Check the followings before and after charging.
Check that F-022 terminal is not wet. Never try to charge the battery when F-022 terminal is wet.
Accessories and optional devices are not waterproof/dustproof.
When charging the battery when or after F-022 terminal is wet, adequately drain it and wipe off water with a dry, clean cloth etc., before connecting the desktop holder or opening the external connection jack cap.
When the external connection jack cap is opened for charging, close the cap firmly after charging. It is recommended that the desktop holder be used for charging to prevent water from seeping inside from the external connection jack.
Do not use the AC adapter or desktop holder in a bathroom, shower room, kitchen, lavatory or other highly humid area. May cause fire or electric shock.
Do not touch the AC adapter or desktop holder with wet hands. May cause electric shock.
1.3 Use the open assist button
You can open F-022 terminal just by pressing the dedicated button.
Even without using the button, you can easily open F-022 terminal.
Point
When pressing the button, it is recommended that you hold F-022 terminal. Be careful not to hit your face, people or objects around you with F-022 terminal, or drop F-022 terminal on the floor due to the momentum of opening it.
Pressing the button may not completely open F-022 terminal, depending on its direction.
Close F-022 terminal with your hand. If F-022 terminal is not completely closed, open it completely, and then try again.
Chapter 1 Introduction
9
F-022_E2kou
F-022.book 10 ページ 2011年2月24日 木曜日 午後2時42分
1.4 Precautions (ALWAYS FOLLOW THESE DIRECTIONS)
Precautions contain the description below.
Handling F-022 terminal, battery, AC adapter, desktop holder and
SIM/USIM (common) ................................................................... 10
Handling F-022 terminal.................................................................. 11
Handling battery .............................................................................. 13
Handling AC adapter and desktop holder ..................................... 14
Handling SIM/USIM......................................................................... 14
Handling mobile phones near electronic medical equipment..... 15
Handling F-022 terminal, battery, AC adapter, desktop holder and SIM/USIM (common)
DANGER
Do not use, store, or leave the equipment in hot areas such as near flames or in areas under strong direct sunlight such as inside a vehicle.
May cause the equipment to be deformed or malfunction, and battery to leak, heat, burst or ignite, and the capability or life to be reduced or shortened. Overheating on parts of the case may cause burns or injuries.
Do not disassemble or remodel the equipment. Do not solder items onto the equipment.
May cause fire, injuries, electric shock, or malfunction. It may also cause the battery to leak, heat, burst or ignite.
Do not let the equipment get wet.
Contact with water or other liquids can cause heating, electric shock, fire, malfunctions or injuries. Take care of the place for use and treatment of the equipment.
Use the battery and AC adapter specified by FUJITSU for your F­022 terminal.
Use of equipment not specified by FUJITSU can cause F-022 terminal, battery and other parts to leak, heat, burst, catch fire or malfunction.
WARNING
Do not put the battery, F-022 terminal, AC adapter or SIM/USIM in microwave ovens or other heating appliances or high­pressure containers.
It may cause the battery to leak, heat, burst or ignite, may cause F-022 terminal or AC adapter to heat, smoke, ignite, or may damage circuits.
Do not throw the equipment or give hard shock to it.
May cause the battery to leak, heat, burst or ignite, and the equipment to malfunction or catch fire.
Keep conductive materials (metal pieces, pencil lead, etc.) from coming in contact with the charging jack or external connection jack. Do not put those materials inside the terminal.
May be subject to electrical short and could cause fire or malfunction.
Turn F-022 terminal OFF before entering a place such as a gas station where flammable gases are generated. Do not charge the battery. The gas may catch fire.
Chapter 1 Introduction
10
F-022_E2kou
F-022.book 11 ページ 2011年2月24日 木曜日 午後2時42分
If the equipment starts giving off a strange smell, overheats, becomes discolored or deformed during use, charging or in storage, immediately perform the following operations.
1. Remove the power plug from the wall outlet.
2. Turn F-022 terminal OFF.
3. Remove the battery from F-022 terminal.
May cause the equipment to heat, burst or ignite or the battery to leak if you keep using the equipment.
CAUTION
Do not leave the equipment on unstable or sloping surfaces.
May cause malfunction or injuries.
Do not store the equipment in extremely humid, dusty or hot areas.
May cause malfunction.
Children using the equipment should be instructed in proper operation by an adult. Do not allow them to use the equipment without adult supervision.
May cause injuries.
Store the equipment out of reach of small children.
May be accidentally swallowed or cause injuries.
Be careful especially when using F-022 terminal connected to the AC adapter continuously for a long time.
If you use a video call while charging the battery for a long time, F-022 terminal, battery and AC adapter may be heated. Directly touching a hot part for a long time, you may have redness, itching or rash on your skin, or it may result in low­temperature burns depending on your constitution or health condition.
Handling F-022 terminal
WARNING
Do not put F-022 terminal in the place such as the dashboard near the airbag, where the influence of air-bag explosion is expected.
When the air-bag explodes, F-022 terminal may hit yourself or others and could cause injury, equipment malfunction or damage.
When you use electronic medical equipment, do not keep the terminal in your chest pocket or inside pocket.
Using your F-022 terminal near medical electronic equipment could cause equipment failure.
Do not put foreign objects such as liquid like water, metal pieces or burnable things into SIM/USIM or microSD card slot.
May cause fire, electric shock or malfunction.
Turn F-022 terminal OFF in areas where use is prohibited, such as in airplanes and hospitals.
May cause electronic equipment or electronic medical equipment to fail or malfunction. If the function which automatically turns the power ON is set, cancel the setting before turning the power OFF. When using the phone in a medical facility, be sure to observe the regulations of the facility. If you do prohibited act such as using the phone in an airplane, you may be punished according to law.
When you talk by setting handsfree, always keep F-022 terminal away from your ear. And, when connecting the earphone/ microphone to F-022 terminal and play a game or music, adjust the volume moderately.
Too loud volume may cause a hearing loss. And, if you cannot hear the sound around you clearly, it may cause an accident.
Chapter 1 Introduction
11
F-022_E2kou
F-022.book 12 ページ 2011年2月24日 木曜日 午後2時42分
If you have weak heart, be careful when setting the Vibrate alert (vibration) or alert volume setting.
Could affect heart function.
If it starts thunder while using the terminal outdoors, turn the power OFF immediately, and move to a safe location.
May be subject to lightning strike and could cause electric shock.
Turn F-022 terminal OFF near high-precision electronic control equipment or electronic equipment using low-power signals.
May cause the equipment to fail or malfunction. * Examples of electronic equipment to avoid. Hearing aids, implanted pacemakers or defibrillators, other electronic medical equipment, fire alarms, automatic doors and other automatic control equipment. Users wearing implanted pacemakers or defibrillators or other electronic medical equipment should check with the manufacturer or sales outlet about the effect of radio frequencies on the equipment.
When the display or camera lens is accidentally broken, be careful of broken glass or exposed internal parts of F-022 terminal.
Surfaces of display and camera lens are made of plastic panels and they are structured for the glass not to scatter, however, if you mistakenly touch broken or exposed parts, you may be injured.
When you sound a high-pitched alarm, always keep F-022 terminal away from your ear.
May cause hearing loss.
CAUTION
Do not swing F-022 terminal by its strap.
May cause the terminal damage or failure, or injury to yourself or others.
When using the motion tracking or motion sensor, check the safety around you, hold F-022 terminal firmly, and do not shake it unnecessarily.
The motion tracking and motion sensor are functions to operate by tilting or shaking F-022 terminal. There is a risk that F-022 terminal hits people or objects around you by shaking it too much, causing a serious accident or damage.
If you put a metal strap or the like to F-022 terminal, be careful not to let the strap hit people or objects around you when performing motion tracking or using motion sensor.
Accidents such as injury, malfunction or damage may result.
If the display part is accidentally broken and liquid crystal leaks out, do not put the liquid in your mouth, inhale, or make contact with your skin. If the liquid gets into your eyes or mouth, rinse it with clean water and see a doctor immediately. And, if the liquid adheres to skin or clothing, use alcohol etc. to wipe it off, then wash with soap.
May cause loss of sight or skin problems.
Do not bring the speaker close to your ear when the ring alert is sounding or you are playing a melody with F-022 terminal.
May cause hearing loss.
In rare cases, using the phone in some vehicle models can cause the vehicle's electronic equipment to malfunction or fail.
In this case, do not use the phone because it may hamper safe driving.
Chapter 1 Introduction
12
F-022_E2kou
F-022.book 13 ページ 2011年2月24日 木曜日 午後2時42分
Mobile phones can give some users skin problems such as itching, allergic reactions or rashes. If you develop skin problems, stop using the phone immediately, and see a doctor.
When opening or closing F-022 terminal, take care not to have your fingers or strap caught by the terminal.
May cause injuries or damages.
Handling battery
Check that the battery type matches the type displayed on the battery label.
S/N Battery type
CA54310-0019 Li-ion battery
DANGER
Do not connect a wire or other metal objects to the jack. And, do not carry or store F-022 terminal with objects like a metal necklace.
May cause the battery to leak, heat, burst or ignite.
Do not try to force the battery onto F-022 terminal if you are having trouble installing it. Always install it after checking that it is correctly oriented.
May cause the battery to leak, heat, burst or ignite.
Do not throw the battery into the fire.
May cause the battery to leak, heat, burst or ignite.
Do not give hard shock to the battery or place heavy objects on it.
May cause the battery to leak, heat, burst or ignite.
If the battery's fluid contacts eyes, immediately flush the eyes with clean water and see a doctor right away. Do not rub the eyes.
May cause loss of sight.
WARNING
If the battery seems to have abnormalities such as deformation or scratches due to an external impact or falling, stop using it immediately.
May cause the battery to leak, heat, burst or ignite, and the equipment to malfunction or catch fire.
If the battery does not have a full charge after being charged for the specified time, stop charging it.
May cause the battery to leak, heat, burst or ignite.
If the battery leaks or gives off a strange smell, immediately remove it from the vicinity of open flames.
The vapors from leaking battery fluid may ignite or explode.
Be careful not to let your pet bite the battery.
May cause the battery to leak, heat, burst or ignite, and the equipment to malfunction or catch fire.
CAUTION
Do not discard old batteries together with other garbage.
May cause igniting or environmental destruction. Tape the terminals of old batteries to insulate them, and then bring them into a sales outlet such as D-PHONE Shop. If your local municipality has a battery recycling program, dispose of them as provided for.
Do not charge a wet battery.
May cause heat generation, ignition or rupture of the battery.
If the battery's fluid contacts skin or clothes, immediately flush the contacted area thoroughly with clean water.
May hurt the skin.
Chapter 1 Introduction
13
F-022_E2kou
01_Safety.fm 14 ページ 2011年2月25日 金曜日 午後4時19分
Handling AC adapter and desktop holder
WARNING
Do not use the USB cable if it gets damaged.
May cause electric shock, heat or fire.
Do not use the AC adapter or desktop holder in a bathroom or other highly humid area.
May cause electric shock.
When it starts to thunder, do not touch F-022 terminal and AC adapter.
May be subject to lightning strike and could cause electric shock.
Do not short the charging jack while it is connected to the outlet. Do not touch the charging jack with a part of your body such as your hand or finger.
May cause fire, malfunction, electric shock or injuries.
Place the AC adapter and desktop holder in a stable location while charging. Do not cover or wrap the AC adapter and desktop holder with a cloth or blanket.
May cause F-022 terminal to be removed or the optional devices to be heated, resulting in fire or troubles.
Do not place heavy objects on the USB cable.
May cause electric shock or fire.
Do not touch the USB cable, desktop holder or outlet with wet hands.
May cause electric shock.
Only use with the specified power source and voltage.
If incorrect voltage is used, this may cause fire or failure.
Do not charge F-022 terminal connecting to a PC with the USB cable.
Charging may not be normally performed.
Chapter 1 Introduction
14
Do not use desktop holder overseas.
May cause malfunctions.
Wipe off any dust that accumulates on the power plug.
May cause fire.
When you connect the AC adapter to an outlet, make sure not to touch with metal such as metal straps and firmly connect to the outlet.
May cause electric shock, electrical short or fire.
When you disconnect the AC adapter from the outlet, do not try to pull the USB cable with excessive force. Instead, hold the AC adapter's power plug to disconnect.
Pulling the cord could damage it, possibly leading to electric shock or fire.
Always remove the power plug from the outlet when not using the AC adapter for an extended period.
May cause electric shock, fire or malfunction.
Immediately remove the power plug from the outlet if water or other fluids get into the AC adapter.
May cause electric shock, smoke or fire.
Handling SIM/USIM
CAUTION
Be careful of the cut surface when removing SIM/USIM.
May hurt hands or fingers.
F-022_E2kou
F-022.book 15 ページ 2011年2月24日 木曜日 午後2時42分
Handling mobile phones near electronic medical equipment
WARNING
Obey the following rules inside medical facilities.
- Do not bring F-022 terminal into operating rooms (ORs), intensive care units (ICUs) or coronary care units (CCUs).
- Turn F-022 terminal OFF in hospital wards.
- Turn F-022 terminal OFF in hospital lobbies and corridors if electronic medical equipment could be nearby.
- If the medical facility has specified zones where use or possession of mobile devices is prohibited, obey those instructions.
- If the function to automatically turn ON the power is set, cancel the setting before turning the power OFF.
Turn F-022 terminal OFF in crowded trains or other public places where pacemaker or defibrillator wearers could be nearby.
F-022 terminal's signals may affect the operation of implanted pacemakers or defibrillators, and other devices.
Wearers of implanted pacemakers or defibrillators must carry and use F-022 terminal at least 22 cm away from the implanted device.
F-022 terminal's signals may affect the operation of implanted pacemakers or defibrillators, and other devices.
When electronic medical equipment other than implanted pacemakers or defibrillators are in use outside of medical facilities (such as in home care settings), check with the device manufacturer to determine how the device is affected by electrical signals.
F-022 terminal's signals may affect the performance of electronic medical equipment.
1.5 Handling precautions
General
F-022 is waterproof/dustproof, however, do not allow water or dust to seep into F-022 terminal and do not allow accessories or optional devices to get wet or let dust attach.
- F-022 terminal is provided with waterproofness of IPX5 and IPX8 (which exceeds IPX7) and dustproofness of IP5X by firmly closing the external connection jack cap and installing the rear cover in a locked state, however, it is not complete waterproofness/dustproofness. Do not install/remove the battery or do not open/close the external connection jack cap and rear cover in the rain or with waterdrop or dirt adhered to them. Water may seep inside and cause corrosion or malfunction. Also, accessories and optional devices are not waterproof/dustproof. Malfunctions, which are determined to be caused by water or dust as result of inspections, are not covered by the warranty. Since these conditions are outside the scope of the warranty, a repair, if at all possible, is charged.
Clean F-022 terminal with a dry soft cloth (such as a cloth for eyeglasses).
- The display of F-022 terminal may have been applied special coating to improve clearness of the color LCD. When cleaning F­022 terminal, rubbing it roughly with a dry cloth can scratch the display. Take care when handling the unit, and clean it with a dry soft cloth (such as a cloth for eyeglasses). Drops of water or dirt left on the display can cause stains or remove the coating.
- If F-022 terminal is wiped with alcohol, paint thinner, benzine or detergent, the printing may disappear or color may fade.
Chapter 1 Introduction
15
F-022_E2kou
F-022.book 16 ページ 2011年2月24日 木曜日 午後2時42分
Clean the jack occasionally with a dry cotton swab etc.
- If the jack is soiled, connection gets worse and it may cause power to be turned off or insufficient battery charge, so clean the jack with a dry cotton swab etc. Also, be careful never to damage the jack when cleaning it.
Do not place F-022 terminal near an air-conditioner outlet.
- The rapid change in temperature may cause condensation, causing internal corrosion and malfunction.
When using, be careful not to subject excessive force to F-022 terminal or the battery.
- If F-022 terminal is crammed into a brimming bag or placed in a pocket and sat on, display, internal PCBs or battery may be damaged or malfunction. And, if external devices are plugged into the external connection jack, the breakage of the connector or malfunction may result.
Do not rub or scrape the display with a metal piece etc.
- It may scratch the display, causing malfunction or damage.
F-022 terminal
Avoid extreme temperature.
- Use F-022 terminal where the temperature ranges between 5 and 40
°
C (limited to the temporary use in a bathroom etc. when
temperature is above 36
°
C) and humidity ranges between 45
and 85%.
F-022 terminal may affect land-line phones, TVs or radios in use nearby, so use it as far as possible from these appliances.
Maintain a separate record of the data you saved in your F-022 terminal.
- If the data is deleted, FUJITSU assumes no responsibility for the loss of any data.
Do not drop F-022 terminal or subject it to shocks.
- May cause malfunction or damage.
Do not plug external devices into the external connection jack at a slant, or do not pull it forcibly while it is plugged.
- May cause malfunction or damage.
Do not close F-022 terminal with the strap etc. held inside.
- May cause malfunction or damage.
It is normal for F-022 terminal to become warm during use or charging. Continue to use it.
Do not leave F-022 terminal with the camera in areas under strong direct sunlight.
- May cause discoloring or burn-in of materials.
F-022 terminal should normally be used with the external connection jack cap closed.
- Dust and/or water brought into F-022 terminal cause troubles.
Do not use F-022 terminal with the rear cover removed.
- It may cause the battery to come off, or may cause a malfunction or damage.
Do not put extremely thick stickers on the display or the key side.
- Doing so may cause malfunction.
While microSD card is being used, do not take the card out and do not turn off F-022 terminal.
- May cause data loss or malfunction.
Do not bring magnetic cards etc. close to F-022 terminal.
- Magnetic data in cash cards, credit cards, telephone cards, floppy disks, etc. may be erased.
Do not bring magnetized objects close to F-022 terminal.
- Bringing strong magnetism close may cause a malfunction.
Chapter 1 Introduction
16
F-022_E2kou
F-022.book 17 ページ 2011年2月24日 木曜日 午後2時42分
Battery
The battery is a consumable part.
- Replace the battery if F-022 terminal has extremely short operation time on a full charge, though it may vary by operating conditions. Purchase a new battery of the specified type.
Charge the battery in an area within the proper ambient temperature range (5-35
Always charge before using it for the first time or after extended
°
C).
disuse.
The operation time provided by the battery varies by the operating environment and battery's deterioration.
The battery may swell out as it comes to near the end of its lifetime depending on the usage conditions, but it is not a problem.
Be careful especially about the following points when preserving or leaving the battery for a long time.
- Keeping under the state of the full charge (right after charging ends)
- Keeping under the state of the empty charge (too exhausted to turn on F-022 terminal) They may cause the battery performance to be degraded or its lifetime to be shortened. For necessary battery level to keep for a long time, the display of battery icon is a state of approximately 2 or 3 cells.
AC Adapter
Do not charge the battery in the areas below.
- In areas of excessive humidity, dust or vibrations
- Near land-line phones or TVs/radios
It is normal for the AC adapter to become hot while charging. Continue to use it.
When using an outlet with a mechanism preventing unplugging, follow the handling instructions for that outlet.
Do not give strong shock. Do not deform the charging jack.
- Doing so may cause malfunction.
SIM/USIM
Do not use excessive force to install/remove SIM/USIM.
It is normal for SIM/USIM to become warm during use. Continue to use it.
Note that FUJITSU assumes no responsibility for malfunctions occurring as the result of inserting and using a SIM/USIM with another IC card reader/writer.
Always keep SIM/USIM ICs clean.
Clean SIM/USIM with a soft, dry cloth (such as a cloth for eyeglasses).
Maintain a separate record of the data you saved in SIM/USIM.
- If the data is deleted, FUJITSU assumes no responsibility for the loss of any data.
Avoid extreme temperature.
Take care not to scratch, touch accidentally or short IC.
- May cause data loss or malfunction.
Do not drop SIM/USIM or subject it to shocks.
- May cause malfunction.
Do not bend SIM/USIM or place heavy objects on it.
- May cause malfunction.
Do not install SIM/USIM into F-022 terminal with a label or sticker put on SIM/USIM.
- May cause malfunction.
Chapter 1 Introduction
17
F-022_E2kou
F-022.book 18 ページ 2011年2月24日 木曜日 午後2時42分
CAUTION
Do not use a remodeled F-022 terminal. Using a remodeled terminal violates the law.
Never open the terminal by removing its screws, or try to modify or repair your terminal yourself. This will void your authority to operate this equipment and invalidate the terminal's certification of technical standard compliance. Repair shall be performed by authorized personnel only. Do not tamper or remove the inscription stickers attached to this terminal, since these stickers certify that the terminal satisfy specific technical standards.
Do not use F-022 terminal while driving a car etc.
Chapter 1 Introduction
18
F-022_E2kou
F-022.book 19 ページ 2011年2月24日 木曜日 午後2時42分
Chapter 2 Get started
2.1 Keys and parts
Keys and Parts
a
Earpiece
b
Display
c
Secondary camera – Shoot yourself or send your image during
video call.
d
Microphone – Do not cover the microphone during a call or
sound recording.
eI Left selection key – Access to functions displayed on the
bottom left of the screen such as Options.
fm Menu key – Open the Main menu. gc Clear key – Delete a previously entered character during text
entry.
hn Call key – Make a phone call. Display the call logs in the
standby mode.
i0 – 9 Number keys – Refer to "Number keys (→P20)". j* *Key – Refer to "Number keys (→P20)".
kT Edit Key – Display text input options such as changing
input mode and language in the text input screen.
l
Light sensor
mk
Navigation keys
g
: Perform an operation.
u
/ d : Move the cursor upward/ downward or adjust volume.
l
/ r : Move the cursor to the left/ right or switch the home screen.
na Right selection key – Access to functions displayed on the
bottom right of the screen.
oC Camera key – Start Main camera. pf Power/End key – End a call. Press and hold to switch the
mobile terminal OFF.
q# # key – Refer to "Number keys (→P20)". rs Profile key – Display the Profile switching list.
sU Pedometer key – Start Pedometer.
– Move the cursor to select an item.
19
F-022_E2kou
F-022.book 20 ページ 2011年2月24日 木曜日 午後2時42分
t
Light – Turn on/blink while receiving a call or closing the mobile
terminal. You can set the pattern or color definitions.
u
Call light – Blink while receiving a call.
Chapter 2 Get started
20
v
Sub-display – Display time and phone number, etc. Display
animation when you close the mobile terminal.
w
Message light – Blink while receiving a message.
x
Antenna
y
Main camera – Shoot photos and videos.
z
Speaker
A
Rear cover
B
Charging jack
C
Rear cover lever
D
Open assist button – You can easily open the mobile terminal
by pressing this button.
E
External connection jack
FM Music/shutter key – Operate Music player and camera. GS / D Volume/zoom key – Adjust the volume, turn on the light
on the sub-display. You can use it as a zoom in/out key when the camera or Mirror is activated.
Number keys
Key Stroke / Alphabet / Function
1
/ One-byte symbol / Voice Mail (press and hold) / ABC
2 3
/ DEF
4
/ GHI
/ JKL
5
? / MNO
6
PQRS
7
TUV
8
WXYZ
9
Space
0 *
(press once) , + (press twice) , P (press 3 times),
W (press 4 times)
#
(Switch characters *Available only for character input)
F-022_E2kou
F-022.book 21 ページ 2011年2月24日 木曜日 午後2時42分
2.2 Attach SIM/USIM/battery
After turning power OFF, close F-022 terminal and hold it in your hand so that you can properly attach SIM/USIM/battery.
Remove rear cover
Slide the rear cover lever in the direction of a to unlock, and then slide the cover in the direction of remove it. Pinch the tab of the inner cover and open the cover in the direction of
Lever
Install SIM/USIM
c
.
Press here with your thumb
Pull the tab with your nail and pull out the tray until it clicks a. Hold SIM/USIM with the IC side down, align the beveled corner with the tray and push into the tray slot until it stops
c
Tab
Tray
.
SIM/USIM
IC
b
by 2 mm with a thumb to
Rear cover
b
. Then push the tray into the
Beveled corner
Tab
Install battery
With the label side of the battery upward, align convex parts of the battery with concave parts of F-022 terminal and slide the battery in the direction of
a
, press the battery in the direction of b to set
it in, and then close the inner cover.
art
Convex p
Battery
Install rear cover
Concave part
Place the 8 tabs of rear cover to the notches, press rear cover in the direction of terminal and rear cover, then slide it in the direction of
a
to avoid forming any clearance between F-022
b
to install it. Finally, slide the lever in the direction of
Rear cover
Point
The inner cover shall be firmly closed for maintaining
c
to lock.
Lever
waterproofness/dustproofness. Opening the cover forcibly may injure your nails or fingers.
Chapter 2 Get started
21
F-022_E2kou
F-022.book 22 ページ 2011年2月24日 木曜日 午後2時42分
To prevent damage due to excessive force, the hinge of the inner cover (the section where F-022 terminal makes contacts) is designed to be removed. If it is detached, align metal pins on the inner cover with the slots on F-022 terminal, and then press the cover until it clicks.
2.3 Use microSD card
F-022 supports microSD card of up to 2 Gbytes, and microSDHC card of up to 16 Gbytes.
Inserting
Turn the mobile terminal OFF, then remove the battery.
1
Insert the microSD card slowly into the slot with metal
2
connectors side down (as shown right), and insert it further until it clicks.
* To remove the microSD card, push it lightly to pop it out, and
then pull it out.
2.4 Use earphone
Connect cable to remote controller (a).
1
Open jack cap (b) of F-022 terminal.
2
Hold the connector horizontally with the arrow side up and
3
insert it to the jack (
Connecting Stereo earphone and microphone
Plug for the terminal
c
).
Connecting plug of Stereo earphone and microphone
External connection jack
Chapter 2 Get started
22
Loading...
+ 55 hidden pages