Fujitsu D3313-S Assembly Instructions Manual

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 1 of 15 www.fujitsu.com

Assembly Instructions

for D3313-S Kit Solution

________________________________________________________________________________________________________________

Table of Contents

Step 1 Prepare the Chassis ............................................................................................................................................. 2

Step 2 Mount the Cooler ................................................................................................................................................. 4

Step 3 Insert RAM ........................................................................................................................................................... 5

Step 4 Put Board in Chassis ............................................................................................................................................ 5

Step 5 Wire HDD ............................................................................................................................................................. 7

Step 6 Mount HDD .......................................................................................................................................................... 8

Step 7 Add Cross Bar ..................................................................................................................................................... 10

Step 8 Close Chassis ...................................................................................................................................................... 11

Optional: Application of a Passive Riser Card + Graphic Card AMD W2100 ................................................................... 12

Step 9 Mount mSata ..................................................................................................................................................... 12

Step 10 Insert Passive Riser Card .................................................................................................................................. 13

Step 11 Add Graphic Card AMD W2100 ........................................................................................................................ 13

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 2 of 15 www.fujitsu.com

Step 1 Prepare the Chassis

Open the chassis with two hands by putting some pressure on your thumbs to push the cover forward.

After opening the chassis take out the contents.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 3 of 15 www.fujitsu.com

Then, remove the cross bar (middle section) of the chassis.

Remove the screw to take out the HDD tray. After removing the screw slide the tray off the chassis.

You should now have

a completely empty

chassis.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 4 of 15 www.fujitsu.com

Step 2 Mount the Cooler

Place the backplate underneath the board, pushing the studs on the backplate through the holes on the board

around the CPU.

Then put the cooler on top of the CPU and screw it onto the backplate through the board. The thermal paste is

already applied.

Now plug in the cooler.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 5 of 15 www.fujitsu.com

Step 3 Insert RAM

If you only have one RAM attach it to the top slot, if you have two, start with the bottom slot.

Put in the first RAM tilted slightly upwards. Then push it down.

Now put in the second RAM in the same manner, putting it in tilted upwards and then pushing it down.

Step 4 Put Board in Chassis

Start by putting all the connectors on the board through the designated holes in the chassis.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 6 of 15 www.fujitsu.com

Now push down the board so that the holes on the board fit onto the screw holes on the chassis.

Now screw in the board in all four holes. The board should now look like this:

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 7 of 15 www.fujitsu.com

Step 5 Wire HDD

At first you need to attach the HDD to the tray you have taken out earlier.

Align the screw holes with the holes on the tray.

Now add screws from the bottom.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 8 of 15 www.fujitsu.com

Step 6 Mount HDD

To mount the HDD place the hooks of the tray on the designated hole in the chassis and push the tray forward.

You can now connect the HDD tray to the board.

Then screw the HDD onto the chassis.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 9 of 15 www.fujitsu.com

Now plug in the power cable.

Connect the SATA cable.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 10 of 15 www.fujitsu.com

Step 7 Add Cross Bar

At first, plug in the front panel cable coming from the

cross bar.

Next, plug in the intrusion cable. On the left of the picture below you can see the plugged in front panel cable.

Then, set the cross bar in its

designated spot on the chassis

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 11 of 15 www.fujitsu.com

Now, turn the chassis around and screw on

the cross bar in the hole as seen in the

pictures.

Step 8 Close Chassis

Slide the cover on top of the chassis and use some pressure to close it all the way.

When the chassis is closed screw it shut through the holes.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 12 of 15 www.fujitsu.com

After you have plugged in the power adapter you can secure it to prevent it from falling out.

Your chassis is now assembled completely.

Optional: Application of a Passive Riser Card + Graphic Card AMD W2100

Step 9 Mount mSata

To carry out this step, you need the mSata, two screws and two nuts.

Place the nuts at the marked position.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 13 of 15 www.fujitsu.com

Put in the mSata tilted slightly upwards. Then

push it down with your fingers and screw on the

mSata as shown in the picture.

Step 10 Insert Passive Riser Card

Insert the passive riser card by putting it into the holder.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 14 of 15 www.fujitsu.com

Step 11 Add Graphic Card AMD W2100

Remove the screw to take out the cover.

After removing the screw slide the cover out of the holder.

Assembly Instructions D3313-S

__________________________________________________________________________________________________________________________________________________________
Page 15 of 15 www.fujitsu.com

Contact

FUJITSU
Fujitsu Technology Solutions Gmbh
Address: Bürgermeister-Ulrich-Straße 100, 86199 Augsburg,
Germany
Phone:
[phone]
Fax : [phone]
E-mail: [e-mail]

© 2016 Fujitsu Technology Solutions GmbH. Fujitsu, the Fujitsu logo are
trademarks or registered trademarks of Fujitsu Limited in Japan and other
countries. Other company, product and service names may be trademarks
or registered trademarks of their respective owners. Technical data subject
to modification and delivery subject to availability. Any liability that the
data and illustrations are complete, actual or correct is excluded.
Designations may be trademarks and/or copyrights of the respective
manufacturer, the use of which by third parties for their own purposes may
infringe the rights of such owner.

Now the graphic card can be added.

Slide in the graphic card to the left. Make sure that the graphic card fits well

at the market points.

Now you can put in the screw again.