Fujitsu D3162-B Tech Note

TechNotes V1.0

Extended Lifecycle Mainboard

D3162-B

a

Content

1 Safety Instructions 4
2 Feature Overview D3162-B 5

2.1 Basic Layout 8

2.2 Block Diagram 9

2.3 External Connectors D3162-B 10

2.4 Onboard components D3162-B 11

2.5 I/O-Shield 12

3 Interfaces & Connectors 14

3.1 Frontpanel Connector 14

3.2 Internal Parallel Port Connector 15

3.3 Internal USB2.0 Connector (2 x 2 Ports) 15

3.4 Internal USB3.0 Connector (1 x 2 Ports) 16

3.5 External USB3.0 Connector 16

3.6 Fan Connector 17

3.7 Power Supply Fan Connector 17

3.8 High Definition Frontpanel Audio Connector (HD Audio) 18

3.9 AC97 Frontpanel Audio Connector (Legacy Audio) 18

3.10 Power Supply Connector 19

3.11 Additional Power Supply Connector 19

3.12 Chassis Intrusion 20

4 System Monitoring 21

4.1 D3162-B: Temperature Sensors and Fan Connectors 22

4.2 D3162-B: SystemGuard 23

4.3 D3162-B: SystemGuard - Details 24

4.4 SilentFanConfigManager – Customize System Monitoring Settings 25

4.5 Components for continous 24/7 operation @ +45°C 26

4.6 Capacitor Endurance Time Comparison 27

4.7 Temperature Reference Points D3162-B 28

a

5 Power Supply 29

5.1 ATX Power Supply 29

6 Display Options 30

6.1 VGA Output 30

6.2 DVI Output 31

6.3 HDMI Output 32

6.4 DisplayPort Output 33

6.5 Dual DVI Output 34

6.6 Multi Monitor Output 35

7 Operating System Support 36

7.1 Support for Windows XP / Windows 7 37

8 Mainboard Tools 38

Common Mainboard Tools 38

8.1 BIOS Boot Logo Tool 38

8.2 EditCMOS 38

8.3 OEMIDENT 38

8.4 SystemGuard 39

9 Known Issues & Important Notes 40

9.1 Windows XP Installation in AHCI mode – necessary adjustments 40

9.2 RAID / AHCI driver disk installation (Windows XP) from floppy disk 41

10 Miscellaneous 42

10.1 System Watchdog (WD) 42

10.2 BIOS Update / BIOS Recovery 43

a

1 Safety Instructions

Safety Instructions

Do not connect or disconnect any cables or modules to or from any onboard connectors (except
for the rear I/O connectors) until the mainboard is completely powered down.

Any damage caused to the mainboard b y misuse of the onboard connectors is excluded from the
standard warranty. Fujitsu Technology Solutions cannot be held liable for any damage that results
from incorrect use of any onboard connectors.

The system integrator is fully responsible for the usage of appropriate connectors and cables in
order to fulfill the technical requirements (electrical contact, durability, power/current levels,
signal integrity etc.)

a

2 Feature Overview D3162-B

• Based on latest Intel

Pantherpoint

single-chip technology (iQ77)

• Support for full range of latest LGA1155 processors (gen2 / gen3; up to 95W)

• Intel® Core™ i7 – 2xxx / i7-37xx processor series

• Intel® Core™ i5 – 2xxx / i5-3xxx processor series

• Intel® Core™ i3 – 2xxx / i3-32xx processor series

• Intel® Pentium® – G6xx / G8xx processor series

• Intel® Celeron® – G4xx / G5xx processor series

• iAMT 8.0 / VPro 2012 Manageabilty Support

Note: Available feature set depends on installed processor

• Four memory sockets DDR3/1066/1333/1600 supporting up to 32GB

• Intel Gbit LAN 82579LM onboard

• iAMT support

a

Feature Overview D3162-B

• Trusted Platform Module TPM V1.2 (Infineon) onboard

• Latest Intel® HD Graphics (integrated in processor)

• Simultaneous use of integrated graphics and PCIe graphics possible

• PCI Express Gen3

• 5.1 multichannel audio onboard

• 4-Layer PCB

a

Feature Overview D3162-B

Designed & approved for 24/7 continuous operation

High Efficiency core voltage regulator design (80-85%)

Extended lifecycle up to 3 years

Hardware Watchdog

 Easy SW integration via Windows API & Linux Driver

a

Feature Overview D3162-B

2.1 Basic Layout

Feature Overview D307x-S

2.2 Block Diagram

Feature Overview D3162-B

2.3 External Connectors D3162-B

PS/2 Kbd / Mouse

4 x USB 2.0

DisplayPort

COM; DVI-I

2 x USB 3.0

LAN1; 2 x USB 2.0

Audio

a

Feature Overview D3162-B

2.4 Onboard components D3162-B

Parallel Port

Frontpanel

PSU Fan Control

Processor Fan (4 pin

Intrusion

12V Supply (Processor)

PCIe x16 (4 Lanes, Gen2)

PCIe x16 (16 Lanes, Gen3)

24 pin ATX PS

Fan 2 (4 pin PWM)

2 x SATA III

4 x SATA II

2x USB 3.0 (Frontpanel)

2 x USB 2.0 (Frontpanel)

2 x USB 2.0 (Internal)

Fan3 (4 pin PWM)

Frontpanel Audio

4 Layer PCB

1 x PCI

1 x PCIe x1

Processor LGA1155

Memory Sockets 4x

a

Feature Overview

2.5 I/O-Shield

Spring Steel Sheet

Enforcement Sheet

(front view)

Rear Side: EMI Gasket

(Foam with Aluminium)

a

Feature Overview

I/O-Shield

Apparatus to evaluate and specify
insertion force of FTS IO shield.

Nominal force: ~ 150 – 200 N (tbd)
for specified ATX IO “letterbox”

Note: ATX Chassis “letterbox” for I/O shield:
Nom. size = 158.75 x 44.45mm
Tolerance = +/- 0.2mm

a

3 Interfaces & Connectors

3.1 Frontpanel Connector

Power LED:
Anode: Pin 2 – 80R Pullup to 5V_AUX
Cathode: Pin 4 – output (12mA)
HDD LED:
Anode: Pin 1 – 365R Pullup to 5V
Cathode: Pin 3 – output (6mA ; ~ 0.7V low level)
Speaker Output:
Differential audio signal; max. 0.5W / 8Ohm

a

Interfaces & Connectors

3.2 Internal Parallel Port Connector

3.3 Internal USB2.0 Connector (2 x 2 Ports)

optional Parallelport cable

with ATX bracket

a

Interfaces & Connectors

3.4 Internal USB3.0 Connector (1 x 2 Ports)

3.5 External USB3.0 Connector

a

Interfaces & Connectors

3.6 Fan Connector

Fan speed control is only supported for 4 pin (PWM) fans.
3-pin fans (voltage controlled) can be connected, but they will always operate
at full speed resp. 12V supply voltage!
Fan current: Max. 1A continuous

3.7 Power Supply Fan Connector

Note: This feature is not supported by standard ATX power supplies!

Note:

Fans must never be attached or

removed while the system is

powered. Mainboard may be

damaged!

a

Interfaces & Connectors

3.8 High Definition Frontpanel Audio Connector (HD Audio)

3.9 AC97 Frontpanel Audio Connector (Legacy Audio)

Note: In case of using this connector in AC97 = Legacy mode (BIOS Setting) take care for pin 7.
This pin is tied to GND. HP_ON# signaling on this pin is not supported.

a

Interfaces & Connectors

3.10 Power Supply Connector

3.11 Additional Power Supply Connector

a

Interfaces & Connectors

3.12 Chassis Intrusion

Note:

The intrusion supervision feature needs to be enabled in BIOS Setup first (Menu „Security“  „Cabinet
Monitoring“).
This BIOS option is only available if pin 3 („Intrusion Switch Present“) is connected to GND!

Note:
Chassis intrusion is active even if the system is switched off (S5 state) or
disconnected from mains power.
The intrusion event is monitored by the chipset (PCH) and stored in the BIOS
Eventlog during the next Boot.
A timestamp (Boot date/time) will be added then.
Note: This timestamp does not represent date/time of the intrusion event!
If a Supervisor Password is enabled in BIOS Setup, the system will stop
during BIOS POST if an intrusion event has been detected. In order to
continue, the Supervisor Password must be entered to confirm the intrusion
event.

The intrusion status can be easily monitored by using the BMCAPI (Windows):

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D3162-B/IndustrialTools_D3162-B/

a

4 System Monitoring

- Temperature Sensors and Fans

- SystemGuard: Fan / Temperature Monitor

- SilentFanConfig-Manager

- Temperature Reference Points

a

System Monitoring

4.1 D3162-B: Temperature Sensors and Fan Connectors

PSU Fan Control

Processor (Fan1; 4 pin PWM)

Sensor “Memory”

Sensor “CoreRegulator”

Fan 2 (4 pin PWM)

Fan 3 (4 pin PWM)

Sensor “PCIe Graphics”

(not yet available in

SystemGuard)

Note: Do not attach more than one fan per connector!
Remove or connect fans only when unit is powered off!

Sensor “Super I/O”

Sensor “Processor”

a

System Monitoring

4.2 D3162-B: SystemGuard

System Monitoring Tool:

• Visualize processor and sensor

temperature data

• Display current speed for all

attached fans

• User can configure fan aging control

(menu “Special”)

• User can configure system watchdog

(menu “Special”)

User can adjust system behaviour via
“Silent PC / Performance PC” slider by
forced processor throttling

a

System Monitoring

4.3 D3162-B: SystemGuard - Details

Temperature Sensors

Processor Sensor

1)

Super I/O Sensor

Memory Sensor

Core Voltage
Regulator Sensor

Sensor / Fan Matrix

 Indicates which sensor influences the specific fan speed
 Note: Characteristics for FAN1 is always dependent on the CPU

temperature – fully controlled by the system BIOS.
Due to safety reasons the influence of the CPU sensor for FAN1
cannot be disabled!

FanPS

 Displays the fan speed of the power supply fan (specific PSU
option)

1) Note: As Intel has replaced the analogue processor „diode“ temperature measurement by the digital
„PECI“ measurement (Platform Environment Control Interface) which does no longer provide the absolute processor

a

System Monitoring

4.4 SilentFanConfigManager – Customize System Monitoring Settings

Note: This option is not yet supported for D3062-B. Support may be possible upon request!

a

Capacitor Endurance Time

Solid Electrolyte:

Fluid Electrolyte:

System Monitoring

4.5 Components for continous 24/7 operation @ +45°C

Operating Conditions:

Circulating air

(mainboard) max. 45°C

Usage 24h / 7 days

All onboard electrolyte

capacitors: Polymer type only

(= solid electrolyte)

Lx = effective endurance time
Lo = endurance time @ 105°C
(e.g. 2.000hrs)
to = 105°C
tx = capacitor surface temperature
(e.g. 75°C)

High Efficiency Processor

Core Voltage Regulator

for reduced thermal

dissipation loss

Note: Power Consumption

PCH  P max ~ 6W

 P idle < 3W

Extra Heatsink

on PCH (Q77)

a

System Monitoring

4.6 Capacitor Endurance Time Comparison

a

System Monitoring

4.7 Temperature Reference Points D3162-B

Battery max. 60/70°C 1)

PCH max. 75°C

(chip surface)

All capacitors max. 60°C

Super I/O max. 70°C

Inductor max. 90°C

1) Note: Battery operation is specified in
temperature range up to 60°C. Operation
between 60°C and 70°C may result in:

- Higher self discharge rate

- Decline of specified characteristics

- Danger of leakage increases

Quartz max. 70°C

LAN max. 75°C

Audio Codec max. 70°C

Reference Point Limit Temperatures (Component Surface) must not be exceeded!

Quartz max. 70°C

Inductor max. 90°C

Power MOS-FET / MOS-FET

Driver max. 90°C

Operating Conditions:

Circulating air

(mainboard) max. 45°C

Usage 24h / 7 days

a

5 Power Supply

5.1 ATX Power Supply

Connectors for ATX Power Supply

(1) 24 pin connector (ATX layout)

(2) 4 pin connector (+12V, GND)

Note: The +12V supply (up to 12A) for processor and chipset is provided via the 4 pin
connector! Onboard voltage regulators convert the +12V input power to the appropriate
processor / chipset supply voltages.

(3) Processor Core Voltage Regulator: High Efficiency Design for enhanced

power saving and less thermal dissipation loss.
Requirements for ATX Power Supply

The ATX power supply should support the minimum load
conditions as mentioned in the chart.

Note: The max. mainboard current in the chart doesn´t include the
power for optional adapters and drives!

(3)

(2)

(1)

a

6 Display Options

6.1 VGA Output

DVI-VGA Interface
Connector

optional: Audio

VGA

max. VGA screen resolution:
1920 x 1200

Analog (VGA) Monitor

a

Display Options

6.2 DVI Output

max. DVI screen resolution:

1920 x 1200

Note: DVI supports Single Link only!

Digital (DVI) Monitor

DVI

optional:

Audio

a

Display Options

6.3 HDMI Output

max. HDMI screen resolution:

1920 x 1200

HDMI transfers Video & Audio

Digital (HDMI) Monitor

Note: HDMI Audio Device needs to be

enabled via Control Panel!

HDMI

DVI-HDMI Interface

Connector

a

Display Options

6.4 DisplayPort Output

max. DP screen resolution:

2560 x 1600

Display Port

Digital (DisplayPort) Monitor

a

Display Options

6.5 Dual DVI Output

DisplayPort-
DVI-Converter
Cable

DVI

DVI

Dual Independent Display /

Extended Desktop

Digital (DVI) Monitor 1

Digital (DVI) Monitor 2

a

Display Options

6.6 Multi Monitor Output

DisplayPort­DVI-Converter
Cable

Digital (DVI) Monitor 1

Digital (DVI) Monitor 2

Digital (DVI) Monitor 3

Digital (DVI) Monitor 4

DVI

DVI

Simultaneous use of internal
Graphics and PCIe Graphics

DVI

DVI

a

7 Operating System Support

- Windows® XP

- Windows® 7

a

Operating System Support

7.1 Support for Windows XP / Windows 7

• Mainboard D3162-B is designed according to the

Microsoft Guidelines for Windows XP and Windows 7

• MS certified drivers (32/64 Bit) are available via OEM DU-DVD

and OEM FTP Server

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D3162-B/Drivers/

a

8 Mainboard Tools

Common Mainboard Tools

8.1 BIOS Boot Logo Tool

- Tool to integrate a customized boot logo

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/BootLogo_4_UEFI/

8.2 EditCMOS

- DOS-based production tool to change BIOS settings
and freeze customized BIOS settings (= customized default settings)
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/EditCMOS_UEFI/

8.3 OEMIDENT

- DOS-based production tool to add MS OEM licence data (SLP1 for Windows XP and SLP2.x for
Windows Vista & Windows 7)

- Add an individual customer serial no / add a chassis asset tag

- Disable and hide TPM feature in BIOS Setup
Link to DOS-based tool and evaluation version of 32Bit tool (Win PE):

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/OEM-Ident/

a

Mainboard Tools

8.4 SystemGuard

- Windows-based tool to monitor temperatures and fan speed of FTS mainboards

- Option to configure automatic fan ageing supervision

- Provides access to the System Watchdog
ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/SystemGuard/

Note: Further details regarding mainboard tools can be found in the related “Mainboard Tools Datasheet”

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Services/Software&Tools/Common-Mainboard-Tools/$$_DS_UEFI-Tools.pdf

a

9 Known Issues & Important Notes

9.1 Windows XP Installation in AHCI mode – necessary adjustments

- Choose BIOS AHCI-mode (ADVANCED – SATA Configuration)

- Download F6 SATA Driver Disk

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D3162-B/Drivers

- Start the Installation of Win XP – press F6 to install SATA drivers

- Use the following Drivers for D3162-B:

- Continue the installation

a

Known Issues & Important notes

9.2 RAID / AHCI driver disk installation (Windows XP) from floppy disk

- D3162-B doesn´t offer a legacy floppy interface

- Windows XP has some limitations regarding USB floppy support, for details see link below

http://support.microsoft.com/kb/916196

- Alternative option: Use nLite-tool to create customized XP installation CD incl. RAID/AHCI driver

www.nliteos.com/nlite.html

a

10 Miscellaneous

10.1 System Watchdog (WD)

D3162-B provides a HW Watchdog for Operating System Runtime supervision.

o Use “WD software agent” to start, stop or retrigger the watchdog during OS runtime

Note: This “agent” needs to be provided by the customer, dependent on his needs.

For easy access to the watchdog functions, the Windows API (BMCAPI) or the related Linux driver (lm-sensors) can be used:

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D3162-B/IndustrialTools_D3162-B/

o For easy testing, the SystemGuard tool provides access to the OS Watchdog. After enabling the Watchdog, SystemGuard retriggers the WD

continuously. In case the system freezes, SystemGuard does no longer provide the retrigger signal and the watchdog resets the system after the timeout.
Note: When SystemGuard is closed, the WD is stopped in order to avoid a unwanted system reset!

Menu “Special”:

--> Enable WD

--> Set timeout to 1 – 8 minutes

a

Miscellaneous

10.2 BIOS Update / BIOS Recovery

BIOS update options

Link to related BIOS files (OEM FTP Server):

ftp://ftp.ts.fujitsu.com/pub/Mainboard-OEM-Sales/Products/Mainboards/Industrial&ExtendedLifetime/D3162-B/BIOS_D3162-B/

 DOS-based BIOS update (DOS-bootable USB stick)

Required BIOS files:

o EfiFlash.exe (DOS flash tool)
o DosFlash.bat (batch file)
o D3162-B.upd (flash file)

Copy unzipped files to a DOS-bootable USB stick, boot system from stick and run

DosFlash.bat

Links to bootable Free-DOS images to create a bootable USB stick:
24MB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=35ac1143-a178-4609-82f2-8bd3a5d2f23d

64MB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=6d835be5-24d0-482b-bbb0-1a3f125e808e
128MB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=3514c169-ac85-44f5-a858-08bdcb38df0e
256MB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=c409d7f4-2494-417f-82ed-395dc850de4d
512MB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=ad35b93d-46f9-4c6a-98ed-7116b86344ff
1GB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=847bbc67-b135-4a95-a173-00cb0c4ecc27
2GB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=c95bc7d7-6fa1-4178-8a61-f55f4bc30706
4GB: http://support.ts.fujitsu.com/Download/ShowDescription.asp?SoftwareGUID=d0ee4c75-14fa-4bdc-a436-099901860e8f

a

Miscellaneous

BIOS Update / BIOS Recovery

 Windows-based BIOS update (Deskflash tool)

Required BIOS file:

o D3162-Bx.R1.x.y.DFI.exe (Windows executable flash tool)

Copy file from FTP (link see above), rename

filename.$xe

to

filename.exe

and copy to target system (e.g. Windows desktop).

Doubleclick to start BIOS update and follow instructions on the screen.

 DOS-based BIOS Recovery (DOS-bootable USB stick)

Required BIOS files:

o EfiFlash.exe (DOS flash tool)
o DosFlash.bat (batch file)
o D3162-Bx.upd (flash file)
o D3162-Bx.rom --> Important: This file must be located in the root directory of the USB stick!

Set onboard jumper to Recovery Mode

Copy unzipped files to a DOS-bootable USB stick,
boot system from stick and run

DosFlash.bat

Follow instructions on the screen and set jumper to default position

Note:
BIOS Recovery should only be used to repair a corrupted BIOS.
All customized data except for OEM SLP data will be reset.

a

54

Copyright 2011 FUJITSU

TechNotes D307x-S V1.1