Fujitsu D1692 Technical Manual

Download

answers 2

Technical Manual

Mainboard D1692

English

Are there ...

... any technical problems or other questions you need clarified?

Please contact:

• your sales partner

• your sales outlet

The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under: http://www.fujitsu-siemens.com

Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt.

Herausgegeben von/Published by Fujitsu Siemens Computers GmbH

Bestell-Nr./Order No.: Printed in the Federal Republic of Germany AG 1103 11/03

A26361-D1692-Z120-1-7619

Mainboard D1692

English

Technical Manual

November 2003 edition

AMD, Opteron, and combinations thereof are trademarks of AMD Corporation.

Broadcom® is a trademark of Broadcom Corporation and/or its subsidiaries

IBM, PC, AT, and PS/2 are trademarks of IBM Corporation

Linux is a trademark of Linus Torvalds

Microsoft, Windows are trademarks of Microsoft Corporation

Phoenix, PhoenixBIOS are trademarks of Phoenix Technologies Ltd.

Silicon Image, SATALink are trademarks of Silicon Image

SuSE is a trademark of SuSE AG

Winbond is a trademark of Winbond Electronics Corporation

All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged.

All rights, including rights of translation, reproduction by printing, copying or similar methods, even of parts are reserved.

Offenders will be liable for damages.

All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Delivery subject to availability.

Right of technical modification reserved.

This manual was produced by cognitas. Gesellschaft für Technik-Dokumentation mbH www.cognitas.de

Contents

Mainboard D1692.............................................................................................................................1

Notational conventions...............................................................................................................1

Important notes .................................................................................................................................2

Information about boards ...........................................................................................................2

List of features...................................................................................................................................3

Board Installation ............................................................................................................................5

D1692 Block Diagram........................................................................................................................5

Board Parts, Jumpers and Connectors..........................................................................................6

J4, J14, J34, J39, J42 and J43 ..........................................................................................................7

SMBus 1.1 Connector (J4).........................................................................................................7

Onboard Buzzer/Speaker header (J14)......................................................................................8

Clear CMOS Jumper (J34) ........................................................................................................8

PCI-X Slots 3 & 4 Force PCI Mode Jumper (J39) ......................................................................8

COM2 Header (J42)...................................................................................................................8

Front Panel Audio Header (J43) ................................................................................................9

J46, J53, J69, J77, J86, J87, J92, J112, J7, J8, J11, J45 and J117 ................................................10

USB E/F (Front Panel Header) (J46) .......................................................................................11

PCI-X Slots 1 & 2 Bus Speed Override (J53)...........................................................................11

Firewire Disable Jumper (J69) .................................................................................................11

INTR – Chassis Intrusion Header (J77) ...................................................................................11

Front Panel Header (J86) ........................................................................................................12

Gigabit Ethernet Disable (J87).................................................................................................12

PCI-X Slots 3 & 4 Bus Speed Override (J92)...........................................................................12

SATA (Serial ATA) Controller Disable (J112)...........................................................................12

RCV (BIOS Recovery) (J7) ......................................................................................................12

BIOS Write Protect (J8)...........................................................................................................13

USB D (with Chipcardreader support) (J11)............................................................................. 13

LCD header (J45) .................................................................................................................... 13

Remote Temp (J117)...............................................................................................................13

CPU and Chassis Fan Connectors ..................................................................................................14

CPU and System Fan Specifications .......................................................................................14

Add-on modules / Upgrading........................................................................................................15

Installing the Processor(s) ...............................................................................................................15

Heat sink Installation................................................................................................................16

Installing the Memory.......................................................................................................................16

Attaching Drive Cables ....................................................................................................................18

Connecting AUX/CD Sound Cables & Speakers..............................................................................19

Installing Add-In Cards ....................................................................................................................20

Connecting External Devices...........................................................................................................21

Installing the Power Supply..............................................................................................................22

Replacing lithium battery .................................................................................................................23

BIOS update....................................................................................................................................24

When should a BIOS update be carried out?...........................................................................24

How does a BIOS update work? .............................................................................................. 24

BIOS Recovery................................................................................................................................24

Glossary ......................................................................................................................................... 25

A26361-D1692-Z120-1-7619 1

Mainboard D1692

Your mainboard is available in different configuration levels. Depending on the configuration chosen, some of the hardware components described may not be available on your mainboard.

Notational conventions

The meanings of the symbols and fonts used in this manual are as follows:

indicates information which is important for your health or for preventing physical

damage.

Ê Text which follows this symbol describes activities that must be performed in the order shown.

↵ This symbol indicates that you must press the Enter key.

Text in this typeface indicates screen outputs.

Text in this bold typeface indicates the entries you make via the keyboard.

Text in italics indicates commands or menu items.

"Quotation marks" indicate names of chapters or terms.

indicates additional information which is required to use the system properly.

A26361-D1692-Z120-1-7619 1

Mainboard D1692

Important notes

With the mainboard installed you must open the system to access the mainboard. How to dismantle and reassemble the system is described in the operating manual accompanying the system.

Connecting cables for peripherals must be adequately shielded to avoid interference.

Observe the safety notes in the operating manual of your system.

Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Replacing lithium battery" section.

Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. There is a danger of burns!

The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility".

Compliance was tested in a typical PC configuration.

When installing the board, refer to the specific installation information in the manual for the receiving device.

The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre.

Information about boards

To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts.

Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage.

Be careful with the locking mechanisms (catches, centring pins etc.) when you replace the mainboard or components on it, for example memory modules or processors.

Never use sharp objects (screwdrivers) for leverage.

Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown.

When you handle boards fitted with ESDs, you must, under all circumstances, observe the following:

• You must always discharge static build up (e.g. by touching a grounded object)

before working.

• The equipment and tools you use must be free of static charges.

• Remove the power plug from the mains supply before inserting or removing

boards containing ESDs.

• Always hold boards with ESDs by their edges.

• Never touch pins or conductors on boards fitted with ESDs.

2 A26361-D1692-Z120-1-7619

Mainboard D1692

List of features

Processor

• Dual µPGA 940-pin ZIF sockets

• Supports up to two AMD Opteron

™

processors

• Two onboard 3-phase VRMs

• 128-bit DDR dual-channel memory controller integrated in CPU

Chipset

• AMD-8131

• AMD-8151

• AMD-8111

™

PCI-X Tunnel

™

AGP Tunnel

™

I/O Hub

• Winbond W83627HF Super I/O

Memory

• 128-bit DDR dual-channel memory bus

• Eight DIMM sockets (four per CPU)

• Supports a total of 16GB of DDR RAM

• Requires registered RAM

• Supports ECC or non-ECC

• Supports PC2700, PC2100, PC1600

Integrated I/O

• One floppy, Two serial (one header and one connector), and one parallel port connector

• PS/2 KB/mouse connectors

• Total six USB connections (three rear connectors, two front USB headers and one internal

USB header with Chipcardreader support)

• One LCD connector

Expansion Slots

• One 8x AGP/AGP-PRO 110W slot (110W only with 550W power supply, else AGP-Pro 50W)

• Four PCI-X slots

• Two 64-bit (3.3v) PCI-X slots support up to 133 MHz on Bus B

• Two 64-bit (3.3v) PCI-X slots support up to 100 MHz on Bus A

• One legacy 32-bit 33MHz PCI slot (5v)

• Total of six usable slots

System Management

• Four 3-pin fan headers with tachometer monitoring and speed control

• 3-pin Chassis Intrusion header

Integrated Enhanced IDE Controller

• Two ports for up to four EIDE devices

• Supports up to ATA-133 IDE devices

A26361-D1692-Z120-1-7619 3

Mainboard D1692

Integrated Audio

• AMD-8111 AC97 Audio Controller

• Analog Devices AD1981b Audio Codec

• One RCA SPDIF digital connector

• Line-in, line-out (headphone capable), mic-in, rear connectors

• Line out (headphone capable) & MIC front panel headers

• Two 4-pin ATAPI Audio headers

Integrated SATA Controller

• Silicon Image SIL3114 SATA

• Four SATA 1.0 channels

• IDE RAID 0, 1, 0+1 (option)

• 48-bit LBA support

Integrated PCI Firewire

• TI TSB43AB22A IEEE1394A controller

• One external and one internal connector

Integrated Gigabit Ethernet

• Broadcom

BCM5703C Gigabit Ethernet

• RJ-45 LAN connector with LEDs

• Connected to PCI-X Bridge A

• (64-bit 100MHz)

Regulatory

• FCC Class B (Declaration of Conformity)

• European Community CE (Declaration of Conformity)

BIOS

• Phoenix BIOS V4.06 on 4Mbit LPC Flash ROM

• ACPI - 2.0

• PXE via Ethernet

• USB device boot

• 48-bit LBA Support

Form Factor

• SSI EEB v3.0 footprint (13" x 12" 330.2x304.8 mm)

• EPS12V SSI Workstation Spec 2.0 (24pin + 8pin + 6pin) power connector

• Serial (one) connector

• Stacked USB 1.1 (three) connectors

• Stacked PS/2 KB/Mouse connectors

• One RJ-45 LAN connectors with LED

• Line-in/Out, Mic, & SPDIF Audio Connectors

Software Specifications

• OS (Operating System) Support

• Microsoft Windows XP Professional

• Microsoft Windows XP x86/64 Professional

• SuSE Linux

• Red Hat

4 A26361-D1692-Z120-1-7619

Board Installation

The mainboard D1692 supports EPS12V/SSI type power supplies (24pin + 8pin + 6pin)

D1692 Block Diagram

and will not operate with any other types. For proper power supply installation procedures see "Installing the Power Supply" section

DO NOT USE ATX 2.x, ATX12V or ATXGES power supplies as they will damage the board and void your warranty.

A26361-D1692-Z120-1-7619 5

Board Parts, Jumpers and Connectors

This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram.

Jumper Legend

OPEN - Jumper OFF without jumper cover

CLOSED - Jumper ON with jumper cover

6 A26361-D1692-Z120-1-7619

Key Pin Missing pin to indicate proper orientation

Board Parts, Jumpers and Connectors

J4, J14, J34, J39, J42 and J43

SMBus 1.1 Connector (J4)

J4 SMBus 1.1 Connector

""""

A26361-D1692-Z120-1-7619 7

Use this connector to connect external SMBUS devices

Pin 1: SMBUS_DATA Pin 2: GND

Pin 3: SMBUS_CLK Pin 4: NC

Board Parts, Jumpers and Connectors

Onboard Buzzer/Speaker header (J14)

J14 Onboard Buzzer/Speaker header

"""" Close Pin-3 and 4 (Default) - Onboard Buzzer Enabled

"""" Open Pin- 3 and 4 - Disable onboard buzzer or connect to chassis speaker

Clear CMOS Jumper (J34)

J34 Clear CMOS Jumper

"""

(Clear)

"""

(Default)

You can reset CMOS settings by using this jumper if you have lost your system/setup password or need to clear system BIOS setting.

There are three easy steps:

Power off system and disconnect all three power connectors from the

motherboard

Use jumper cap to close Pin2 and Pin3 for several seconds to Clear CMOS Put jumper cap back to Pin1 and Pin2 (default setting)

Reconnect power & power on system

NOTE: If you do not disconnect the power connectors from the motherboard the

CMOS may not clear completely.

PCI-X Slots 3 & 4 Force PCI Mode Jumper (J39)

J39 PCI-X Slots 3 & 4 Force PCI Mode Jumper

"" Open - (Default) Allows PCI 3 & 4 to operate in PCI-X mode

"" Closed - Force PCI slots 3 & 4 to operate in PCI compatibility mode

Close this jumper if the card you are using does not support PCI-X

COM2 Header (J42)

J42 COM2 Header

"" "" "" "" "!

8 A26361-D1692-Z120-1-7619

Use these pin definitions to connect a port to COM2

Signal Pin Pin Signal

Data Carrier Detect

Receive-Data Transfer-Data

Data Terminal Ready

Ground

1 2 3 4 5 6 7 8 9 10

Data-Set-Ready

Request-to-Send

Clear-to-Send Ring-Indicator

NC/KEY

Board Parts, Jumpers and Connectors

Front Panel Audio Header (J43)

J43 Front Panel Audio Header

"" "" "" "! ""

If you remove the front panel audio cable you have to put jumpers on Pin 5&6 and Pin 9&10 to get audio or microphone signals on your front or rear audio connections.

Signal Pin Pin Signal

MIC In FP MIC BIAS

Right Front out

No Connect

Left Front Out

12 34 5 6 78 9 10

Audio GND

Audio Analog Right Rear In

Key

Left Rear In

WARNING: Do not place jumpers on this header in any other configuration. Doing

so could result in damage to the motherboard!

A26361-D1692-Z120-1-7619 9

Board Parts, Jumpers and Connectors

J46, J53, J69, J77, J86, J87, J92, J112, J7, J8, J11, J45 and J117

10 A26361-D1692-Z120-1-7619

Board Parts, Jumpers and Connectors

USB E/F (Front Panel Header) (J46)

J46 USB E/F (Front Panel Header)

"" "" "" "" !"

Signal Pin Pin Signal

VCC

Data -

Data +

GND

KEY

1 2

3 4

5 6

7 8

9 10

VCC

Data -

Data +

GND

PCI-X Slots 1 & 2 Bus Speed Override (J53)

J53 PCI-X Slots 1 & 2 Bus Speed Override

"" Open – (Default) Allows PCI slots 1 & 2 to operate at up to 133MHz (Maximum

one PCI-X 133 device)

"" Closed – Forces PCI slots 1 & 2 to operate at a maximum bus speed of 100 MHz

Close this jumper if using more than one PCI-X 133 card on this bus

Firewire Disable Jumper (J69)

J69 Firewire Disable Jumper

"" Open – (Default) Enables onboard FireWire controller

"" Closed – Disables onboard FireWire controller

INTR – Chassis Intrusion Header (J77)

J77 INTR – Chassis Intrusion Header

Active Low """

Pin 1 Presence Detect Pin 2 Case Open Pin 3 GND

A26361-D1692-Z120-1-7619 11

Board Parts, Jumpers and Connectors

Front Panel Header (J86)

J86 Front Panel Header

Gigabit Ethernet Disable (J87)

J87 Gigabit Ethernet Disable

"" Open – (Default) Enable onboard LAN Controller

"" Closed – Disable onboard LAN Controller

PCI-X Slots 3 & 4 Bus Speed Override (J92)

J92 PCI-X Slots 3 & 4 Bus Speed Override

"" Open – (Default) Allows PCI 3 & 4 to operate at up to 100MHz

"" Closed – Force PCI slots 3 & 4 to operate in at a maximum 66MHz

Note: This jumper affects integrated Ethernet on the same bus

SATA (Serial ATA) Controller Disable (J112)

J112 SATA (Serial ATA) Controller Disable

"" Open – (Default) Enable onboard SATA Controller

"" Closed – Disable onboard SATA Controller

RCV (BIOS Recovery) (J7)

J7 RCV (BIOS Recovery)

"" Open – (Default)

"" Closed – Recovery mode

12 A26361-D1692-Z120-1-7619

Board Parts, Jumpers and Connectors

BIOS Write Protect (J8)

J8 BIOS Write Protect

"" Open – (Default)

"" Closed – FWH write protection

USB D (with Chipcardreader support) (J11)

J11 USB D (with Chipcardreader support)

"" "" "" "" !"

Signal Pin Pin Signal

Key

n.c. 3 4

n. c.

Key

1 2

5 6

7 8

9 10

11 12

LCD header (J45)

J45 LCD header

"" "" !" "" "" "" ""

Signal Pin Pin Signal

Clock

Data

Key

LAN Action

IDE

Message

Power

1 2

3 4

5 6

7 8

9 10

11 12

13 14

CCR on

VCC

Data +

Data -

GND

n. c.

GND

RFU

LAN Link

Alert

Sleep

VDD

Remote Temp (J117)

J117 Remote Temp

"""

A26361-D1692-Z120-1-7619 13

Pin1: GND Pin2: Remote_Temp Pin3: GND

Board Parts, Jumpers and Connectors

CPU and Chassis Fan Connectors

CPU and System Fan Specifications

All CPU & System fan headers use the same pinout listed on the left.

FAN1: Max 1.2 Amp CPU fan. Controlled and monitored

FAN2: Max 1.2 Amp CPU fan.Controlled and monitored

FAN3: Max 3.0 Amp Rear fan. Controlled and monitored

FAN6: Max 2.0 Amp Front fan. Controlled and monitored

FAN4: Max 2.0 Amp AUX fan. This fan header is not controlled or monitored

FAN5: This fan header is not controlled or monitored

14 A26361-D1692-Z120-1-7619

Add-on modules / Upgrading

Installing the Processor(s)

The mainboard D1692 supports the latest 64-bit processor technologies from AMD. Only AMD Opteron

Fujitsu Siemens Computers is not liable for damage as a result of operating an unsupported configuration.

The diagram is provided as a visual guide to help you install socket processors and may not be an exact representation of the processors you have.

► Lift the lever on the socket until it is approximately 90o or as far back as possible to the socket.

► Align the processor with the socket. There are keyed pins underneath the processor to ensure

► Seat the processor firmly into the socket by gently pressing down until the processor sits flush

™

processor 200 series are certified and supported with this motherboard.

If using a single processor, it MUST be installed in socket CPU0. When using a single

processor only CPU0 memory banks are addressable. There must be used identical processors for CPU0 and CPU1.

that the processor is installed correctly.

with the socket.

► Place the socket lever back down until it locks into place.

Your processor is installed.

Repeat these steps for the second processor if you are using two processors.

A26361-D1692-Z120-1-7619 15

Add-on modules / Upgrading

Heat sink Installation

• The thermal interface material is attached to the heat sink and protected with a plastic cover.

Remove the plastic cover from the heat sink.

• Place the heat sink directly on the processor.

• Secure the metal clips to the plastic retention brackets.

After you have finished installing the heat sink onto the processor and socket, attach the end wire of the fan (which should already be attached to the heat sink) to the motherboard.

The diagram illustrates how to connect fans onto the motherboard.

Installing the Memory

Before attempting to install any memory, make sure that the memory you have is compatible with the motherboard as well as the processor.

The following diagram shows common types of DDR SDRAM modules:

16 A26361-D1692-Z120-1-7619

Add-on modules / Upgrading

Here are a few key points to note before installing memory into your mainboard D1692.

• Always install memory beginning with CPU0/DIMMA1 and CPU0/DIMMA2.

• In order to access memory on CPU1; both processors must be installed.

• Configure memory symmetrically for each CPU for best performance.

• AMD OpteronTM processors support 64bit (non-interleaved) or 128bit (interleaved) memory

configurations (See chart).

• At least one Registered DDR SDRAM module (CPU0/DIMMA1 or CPU0/DIMMB1) must be

installed for the system to turn on and POST (power on self test).

• 128MB, 256MB, 512MB, 1GB, and 2GB Registered PC2700/ PC2100/PC1600 DDR SDRAM

memory modules are supported.

• All installed memory will be automatically detected.

• The mainboard D1692 supports up to 8GB with two CPUs installed.

• Use only identical DIMMs for one channel.

• Memory must be installed in pairs of DIMMs (CPU0/DIMMA1 and CPU0/DIMMA2,

CPU0/DIMMB1 and CPU0/DIMMB2, CPU1/DIMMA1 and CPU1/DIMMA2, CPU1/DIMMB1 and CPU1/DIMMA2).

Following memory configurations are allowed

CPU0 CPU1 CPU0/

X X X

X X X X X

X X X X X X

X X X X X X X X X X

Do not use PC3200 memory modules because they require another reference voltage.

X indicates a populated CPU socket or a populated DIMM Slot.

DIMMA1

CPU0/

DIMMA2

CPU0/

DIMMB1

CPU0/

DIMMB2

CPU1/

DIMMA1

CPU1/

DIMMA2

CPU1/

DIMMB1

CPU1/

DIMMB

A26361-D1692-Z120-1-7619 17

Add-on modules / Upgrading

Memory Installation Procedure

When you install the memory modules, make sure the module aligns properly with the memory slot. The modules are keyed to ensure that it is inserted only one way. The method of installing memory modules are detailed by the following diagrams.

Once the memory modules are firmly seated in the slot, two latches on either side will close and secure the module into the slot. Sometimes you may need to close the latches yourself.

To remove the memory module, simply push the latches outwards until the memory module pops up. Then remove the module.

YOU MUST ALWAYS unplug the power connector from the motherboard before

performing system hardware changes. Otherwise you may damage the board and/or expansion device.

Attaching Drive Cables

Attaching the IDE drive cable is simple. These cables are “keyed” to only allow them to be connected in the correct manner. The mainboard D1692 has two on-board IDE channels, each supporting two drives. The black connector designates the Primary channel, while the white connector designates the Secondary channel.

Simply plug in the BLUE END of the IDE cable into the motherboard IDE connector, and the other end(s) into the drive(s). Each ATA-133 IDE cable has three connectors, two of which are closer together. The BLUE connector that is furthest away from the other two is the end that connects to the motherboard. The other two connectors are used to connect to drives.

18 A26361-D1692-Z120-1-7619

Add-on modules / Upgrading

Notes:

• Always remember to properly set the drive jumpers.

• If only using one device on a channel, it should be set as Master.

• If only using one device on a channel connect it to the last connector.

• The maximum supported length of an IDE cable is 18”.

• There are no Master/Slave jumpers on SATA drives.

The mainboard D1692 is also equipped with four Serial ATA (SATA) channels.

The following pictures illustrate how to connect an SATA drive.

1 = SATA drive cable connection 2 = SATA drive power connection 3 = SATA cable motherboard connector 4 = SATA drive power adapter

Floppy Drives

Attaching floppy diskette drives are done in a similar manner to hard drives. In most cases, there will be a key pin on the cable which will force a proper connection of the cable. Attach floppy drive (drive A:) to the end of the cable with the twist in it.

Connecting AUX/CD Sound Cables & Speakers

There are two connectors available for CD audio AUX audio. Both connectors are 4-pin. See the illustration below for pinouts.

Audio_L

Audio_GND

Audio_R

A26361-D1692-Z120-1-7619 19

Add-on modules / Upgrading

Rear Audio Connectors

Digital SPDIF COAX

Digital interface Supports 5.1 Digital Surround Sound

Analog Connectors

Line in

Line out (headphone capable)

Microphone In

Installing Add-In Cards

Before installing add-in cards, you should ensure that they are fully compatible with your motherboard. If in doubt, check the specifications with the manufacturer.

In order to illustrate the most common slots and what they support; we have provided the illustrations below.

Simply find the appropriate slot for your add-in card and insert the card firmly.

Never force any add-in cards into any slots if they do not seat in place. Doing so will damage the motherboard and void your warranty.

*The AGP slot supports AGPPRO & 1.5v(4x/8x) AGP cards only

20 A26361-D1692-Z120-1-7619

Add-on modules / Upgrading

PCI Interrupt Routing Table

Slot or Device Bus# AMD8111 AMD8131

A B C D A B C D

AGP SLOT N/A A B

PCI Slot #1 (64bit) PCIX-B

PCI Slot #2 (64bit) PCIX-B

PCI Slot #3 (64bit) PCIX-A

PCI Slot #4 (64bit) PCIX-A

PCI Slot #5 (32bit) PCI 0 A

Onboard SATA PCI 0

Onboard GB LAN PCIX-A

Onboard FireWire PCI 0

IDE A

USB

AC’97 Audio

B C D

A B C D

A B C

B C D A

C D A B

Each row represents one slot or onboard device, each column represents one PCI Interrupt Line. All devices on one column share this line. For standard PCI cards or devices (e.g. those that use only one interrupt) an “A“ in a column means that it uses this PCI Interrupt Line. If other cards or devices also use this line, this means the line is shared. According to the PCI specification all cards and devices must support interrupt sharing. Some cards, however, might cause instabilities or performance degradation if they share an interrupt. Try moving those cards to a slot where they won’t share an interrupt.

Some cards may use more than one interrupt. For these cards also take into consideration the small “B” “C” “D” entries in the table.

YOU MUST ALWAYS unplug all three power connectors from the motherboard before

performing system hardware changes. Otherwise you may damage the board and/or expansion device.

Connecting External Devices

Connecting external devices to the motherboard is an easy task. The standard devices you should expect to plug into the motherboard are keyboards, mice, and printer cables. The following diagram will detail the ATX port stack for the mainboard D1692:

A26361-D1692-Z120-1-7619 21

Add-on modules / Upgrading

Installing the Power Supply

There are three power connectors on your mainboard D1692.

The mainboard D1692 requires an EPS12V (24-pin + 8-pin) power supply to boot.

You also have an option of using an SSI V3.0 spec. Workstation power supply. This is only necessary when an AGP PRO110W card is used. (For more information see www.ssiforum.org

NEVER plug the 8-pin power connector into the 6-pin motherboard connector. Doing

Please be aware that ATX 2.x and ATXGES power supplies are not compatible with the board and can damage the motherboard and/or CPU(s).

so will damage the motherboard and/or other components

)

Disconnect power supply from electrical outlet

► Connect the EPS12V 8-pin power connector.

► Connect the SSI Workstation 6-pin power connector (if needed).

► Connect the EPS12V 24-pin power connector.

► Connect power cable to power supply to power outlet.

► Make sure you have connected all three connectors before attempting to apply power to the

board.

22 A26361-D1692-Z120-1-7619

Add-on modules / Upgrading

Replacing lithium battery

In order to permanently save the system information, a lithium battery is installed to provide the CMOS-memory with a current. A corresponding error message notifies the user when the charge is too low or the battery is empty. The lithium battery must then be replaced.

Incorrect replacement of the lithium battery may lead to a risk of explosion!

The lithium battery holder exists in different designs that function in the same way.

The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer.

Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste.

Ensure that you insert the battery the right way round. The plus pole must be on the top!

Ê Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the

holder (1).

Ê Remove the battery (2).

Ê Insert a new lithium battery of the same type into the socket (3).

A26361-D1692-Z120-1-7619 23

Add-on modules / Upgrading

BIOS update

When should a BIOS update be carried out?

Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated.

A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software.

How does a BIOS update work?

► Download the update file from our website to your PC.

► Insert an empty floppy disk (1.44 MB).

► Run the update file (e.g. 1692102.EXE).

► A bootable update floppy disk is created. Leave this floppy disk in the drive.

► Restart the PC.

► Follow the instructions on screen.

BIOS Recovery

► Opening the casing as described in the operating manual.

► Close the jumper RCV (J7).

► Close the casing as described in the operating manual.

► Insert a BIOS Recovery Disk and start the PC.

► Note the signals issued from the buzzer or loudspeaker. You have successfully restored the

► Power off your system.

► Open the casing as described in the operating manual.

► Remove the jumper RCV (J7).

► Close the casing as described in the operating manual.

All BIOS settings are reset to the default values.

BIOS if you hear one long beep.

► Remove the floppy disk from the drive.

► Start the PC and invoke BIOS Setup.

► Select the menu item Reset configuration in the menu Advanced and change the setting to Yes.

► Save the change and terminate BIOS Setup.

The BIOS recovery has now been completed. The system restarts.

24 A26361-D1692-Z120-1-7619

Glossary

The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations. Not all technical terms and abbreviations listed here are valid for the described mainboard.

ACPI Advanced Configuration and

Power Management Interface AC'97 Audio Codec '97 LAN Local Area Network AGP Accelerated Graphics Port LSA LAN Desk Service Agent AMR Audio Modem Riser MCH Memory Controller Hub AOL Alert On LAN MMX MultiMedia eXtension APM Advanced Power Management P64H PCI64 Hub ATA Advanced Technology

Attachment BIOS Basic Input Output System PXE Preboot eXecution Environment BMC Baseboard management

controller CAN Controller Area Network RAMDAC Random Access Memory Digital

CPU Central Processing Unit RDRAM Rambus Dynamic Random

CNR Communication Network Riser RIMM Rambus Inline Memory Module C-RIMM Continuity Rambus Inline

Memory Module DIMM Dual Inline Memory Module SB Soundblaster ECC Error Correcting Code SDRAM Synchronous Dynamic Random

EEPROM Electrical Erasable

Programmable Read Only

Memory FDC Floppy disk controller SIMD Streaming Mode Instruction

FIFO First-In First-Out SMBus System Management Bus FSB Front Side Bus SVGA Super Video Graphic Adapter FWH Firmware Hub USB Universal Serial Bus GMCH Graphics and Memory Controller

Hub GPA Graphics Performance

Accelerator I2C Inter Integrated Circuit IAPC Instantly Available Power

Managed Desktop PC Design ICH I/O Controller Hub IDE Intelligent Drive Electronics IPSEC Internet Protocol Security

ISA Industrial Standard Architecture

PCI Peripheral Component

Interconnect

RAM Random Access Memory

Analogue Converter

Access Memory

RTC Real Time Clock

Access Memory

SGRAM Synchronous Graphic Random

Access Memory

(

Single Instruction Multiple Data)

VGA Video Graphic Adapter

WOL Wake On LAN

A26361-D1692-Z120-1-7619 25

Fujitsu D1692 Technical Manual

Specifications and Main Features

Frequently Asked Questions

User Manual