FujiFilm Real 3D V3 User Manual
BL01547-200
EN
DIGITAL VIEWER
FINEPIX REAL D V
Owner’s Manual
Thank you for your purchase of this product. This
manual describes how to use your FUJIFILM FinePix
REAL 3D V3 digital viewer. Be sure that you have
read and understood its contents before using the
viewer.
Before You Begin
First Steps
Viewing Pictures
Other Options
Troubleshooting
Appendix
FUJIFILM Worldwide Network
For information on related products, visit our website at
http://www.fujifilm.com/products/index.html
Installation
Antennas
Use
Service
For Your Safety
For Your Safety
• Read Instructions: All the safety
and operating instructions
should be read before the appliance is operated.
• Retain Instructions: The safety
and operating instructions
should be retained for future
reference.
• Heed Warnings: All warnings on
the appliance and in the operating instructions should be
adhered to.
• Follow Instructions: All operating
and use instructions should be
followed.
Installation
Power Sources: This video product should be operated only
from the type of power source
indicated on the marking label.
If you are not sure of the type
of power supply to your home,
consult your appliance dealer or
local power company. For video
products intended to operate
from battery power, or other
sources, refer to the operating
instructions.
Grounding or Polarization: This
video product is equipped with
a polarized alternating-current
line plug (a plug having one
blade wider than the other).
This plug will t into the power
outlet only one way. This is a
safety feature. If you are unable
to insert the plug fully into the
outlet, try reversing the plug.
If the plug should still fail to t,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of
the polarized plug.
Alternate Warnings: This video
product is equipped with a
three-wire grounding-type plug,
a plug having a third (grounding)
pin. This plug will only t into a
grounding-type power outlet.
This is a safety feature. If you are
unable to insert the plug into the
outlet, contact your electrician to
replace your obsolete outlet. Do
not defeat the safety purpose of
the grounding type plug.
Overloading: Do not overload
wall outlets and extension
cords as this can result in a risk
of re or electric shock.
Ventilation: Slots and openings
in the cabinet are provided for
ventilation, to ensure reliable
operation of the video product
IMPORTANT SAFETY INSTRUCTIONS
and to protect it from overheating, and these openings must
not be blocked or covered.
The openings should never be
blocked by placing the video
product on a bed, sofa, rug, or
other similar surface.
This video product should not
be placed in a built-in installation such as a bookcase or
rack unless proper ventilation is
provided or the manufacturer’s
instructions have been adhered
to. This video product should
never be placed near or over a
radiator or heat register.
Attachments: Do not use attachments not recommended by
the video product manufacturer as they may cause hazards.
Water and Moisture:
this video product near water—for example, near a bath
tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement,
or near a swimming pool, and
the like (excluding waterproof
products).
Power-Cord Protection: Powersupply cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them,
paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the appliance.
Accessories: Do not place this
video product on an unstable
cart, stand, tripod, bracket, or
table. The video product may
fall, causing serious injury to a
child or adult, and serious damage to the appliance. Use only
with a cart, stand, tripod, bracket, or table recommended by
the manufacturer, or sold with
the video product. Any mounting of the appliance should follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
An appliance
and cart
combination
should be
moved with
care. Quick
stops, excessive force, and uneven surfaces may cause the
appliance and cart combination
to overturn.
Do not use
Antennas
Outdoor Antenna Grounding: If an
outside antenna or cable system is connected to the video
product, be sure the antenna
or cable system is grounded
so as to provide some protection against voltage surges and
built-up static charges. Section
810 of the National Electrical
Code, ANSI/NFPA No. 70, provides information with respect
to proper grounding of the
mast and supporting structure,
grounding of the lead-in wire
to an antenna discharge unit,
size of grounding conductors,
location of antenna discharge
unit, connection to grounding
electrodes, and requirements
for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL ELECTRICAL CODE
Ground Clamp
Electric Service
Equipment
Ground Clamps
Power Service Grounding
Electrode System (NEC ART
250. PART H)
Power Lines: An outside antenna
system should not be located in
the vicinity of overhead power
lines or other electric light or
power circuits, or where it can
fall into such power lines or
circuits. When installing an outside antenna system, extreme
care should be taken to keep
from touching such power lines
or circuits as contact with them
might be fatal.
Use
Cleaning: Unplug this video
product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
Object and Liquid Entry: Never push
objects of any kind into this
video product through openings as they may touch dangerous voltage points or short out
parts that could result in a re or
electric shock. Never spill liquid
of any kind on the video product
(excluding waterproof products).
Lightning: For added protection
for this video product receiver
during a lightning storm, or when
Antenna Lead
in Wire
Antenna
Discharge Unit
(NEC SECTION
810-20)
Grounding
Conductors (NEC
SECTION 810-21)
it is left unattended and unused
for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the
video product due to lightning
and power-line surges.
Service
Servicing: Do not attempt to service this video product yourself
as opening or removing covers
may expose you to dangerous
voltage or other hazards. Refer
all servicing to quali ed service
personnel.
Damage Requiring Service: Unplug
this video product from the
wall outlet and refer servicing
to quali ed service personnel
under the following conditions:
• When the power-supply cord
or plug is damaged.
• If liquid has been spilled, or
objects have fallen into the
video product.
• If the video product has been
exposed to rain or water (excluding waterproof products).
• If the video product has been
dropped or the cabinet has
been damaged.
If the video product does not
operate normally follow the operating instructions. Adjust only
those controls that are covered
by the operating instructions
as an improper adjustment of
other controls may result in
damage and will often require
extensive work by a quali ed
technician to restore the video
product to its normal operation.
When the video product exhibits a distinct change in performance—this indicates a need
for service.
Replacement Parts: When replacement parts are required, be sure
the service technician has used
replacement parts speci ed
by the manufacturer or have
the same characteristics as the
original part. Unauthorized
substitutions may result in re,
electric shock or other hazards.
Safety Check: Upon completion
of any service or repairs to this
video product, ask the service
technician to perform safety
checks to determine that the
video product is in proper operating condition.
ii
For Your Safety
WARNING
WARNING
CAUTION
Be sure to read these notes before use
Safety Notes
• Make sure that you use your product correctly. Read these safety notes and your Owner’s Manual carefully before use.
• After reading these safety notes, store them in a safe place.
The icons shown below are used in this document to indicate the
About the Icons
severity of the injury or damage that can result if the information
indicated by the icon is ignored and the product is used incorrectly as a result.
This icon indicates that death or serious injury can result if the
information is ignored.
WARNING
This icon indicates that personal injury or material damage can
result if the information is ignored.
CAUTION
The icons shown below are used to indicate the nature of the instructions which are to be observed.
Triangular icons tell you that this information requires attention
(“Important”).
Circular icons with a diagonal bar tell you that the action indicated
is prohibited (“Prohibited”).
Filled circles with an exclamation mark indicate an action that
must be performed (“Required”).
If a problem arises, turn the device o and disconnect and unplug the
AC power adapter. Continued use of the device when it is emitting
smoke, is emitting any unusual odor, or is in any other abnormal
Unplug from
state can cause a fi re or electric shock. Contact your FUJIFILM
power socket
dealer.
Do not allow water or foreign objects to enter the device. I f water or
foreign objects get inside the device, turn the device off and disconnect and unplug the AC power adapter. Continued use of the
Avoid exposure
device can cause a fi re or electric shock. Contact your FUJIFILM
to water
dealer.
Do not use the device in the bathroom or shower. This can cause a fi re
Do not use in
or electric shock.
the bathroom
or shower
Never attempt to change or take apart the device. (Never open the casing.) This can cause a fi re or electric shock.
Do not
disassemble
Should the case break open as the result of a fall or other accident, do
not touch the exposed parts. Failure to observe this precaution could
result in electric shock or in injury from touching the damaged
parts. Disconnect the AC power adapter immediately, taking care
Do not touch
internal parts
to avoid injury or electric shock, and take the product to the point
of purchase for consultation.
Do not change, heat or unduly twist or pull the connection cord and do
not place heavy objects on the connection cord. These actions could
damage the cord and cause a fi re or electric shock. If the cord is
damaged, contact your FUJIFILM dealer.
Do not place the device on an unstable surface. This can cause the
device to fall or tip over and cause injury.
Never attempt to view pictures while in motion. Do not use the device
while you are walking or driving a vehicle. This can result in you
falling down or being involved in a traffi c accident.
Do not touch any metal parts of the device during a thunderstorm. This
can cause an electric shock due to induced current from the lightning discharge.
Do not use the battery except as speci ed. Load the battery as shown
by the indicator.
WARNING
Do not heat, change or take apart the battery. Do not drop or subject
the battery to impacts. Do not store the battery with metallic products.
Any of these actions can cause the battery to burst or leak and
cause fi re or injury as a result.
Use only the AC power adapters speci ed for use with this device. Do not
use voltages other than the power supply voltage shown. The use of
other power sources can cause a fi re.
If the battery leaks and uid gets in contact with your eyes, skin or clothing, ush the a ected area with clean water and seek medical attention
or call an emergency number right away.
When carrying the battery, install it in the remote control or keep it in
a plastic case. When storing the battery, keep it in a plastic case. When
discarding, cover the battery terminals with insulation tape. Contact
with other metallic objects or batteries could cause the battery
to ignite or burst.
Keep memory cards and USB memory out of the reach of small children.
These small devices are easily swallowed and should be kept out
of reach of small children. If a child swallows a storage device, seek
medical attention or call an emergency number.
Do not use in the presence of steam or ammable gas or (with the exception of waterproof products) in locations exposed to high levels of
humidity or dust. This can cause a fi re or electric shock.
Do not leave this device in places subject to extremely high temperatures. Do not leave the device in locations such as a sealed vehicle
or in direct sunlight. This can cause a fi re.
Keep out of the reach of small children. This product could cause injury in the hands of a child.
Do not place heavy objects on the device. This can cause the heavy
object to tip over or fall and cause injury.
Do not move the device while the AC power adapter is still connected.
Do not pull on the connection cord to disconnect the AC power adapter.
This can damage the power cord or cables and cause a fi re or
electric shock.
Do not cover or wrap the device or the AC power adapter in a cloth or
blanket. This can cause heat to build up and distort the casing
or cause a fi re.
When you are cleaning the device or you do not plan to use the device
for an extended period, disconnect and unplug the AC power adapter.
Failure to do so can cause a fi re or electric shock.
When a memory card is removed, the card could come out of the slot too
quickly. Use your nger to hold it and gently release the card.
Request regular internal testing and cleaning for the device. Build-up
of dust in the device can cause a fi re or electric shock. Contact
your FUJIFILM dealer to request internal cleaning every two years.
Please note that this service is not free of charge.
WARNING
CAUTION
iii
For Your Safety
Button Batteries
AC Power Adapters
Electrical Interference
Liquid Crystal
For Customers in the U.S.A.
FCC Statement
CAUTION
Notes on the Grant
For Customers in Canada
The Battery and Power Supply
Button Batteries
• Do not immerse in or expose to water.
• Cease use immediately should you notice leakage, deformation,
discoloration, or other abnormalities.
• Insert in the correct orientation.
in the unlikely event of the battery leaking, remove any
liquid from the battery chamber and insert a fresh battery.
AC Power Adapters
Use only FUJIFILM AC power adapters designated for use with this
device. Other adapters could damage the device.
• The AC power adapter is for indoor use only.
• Be sure the DC plug is securely connected to the device.
• Turn the device o before disconnecting the adapter. Disconnect
the adapter by the plug, not the cable.
• Do not use with other devices.
• Do not disassemble.
• Do not expose to high heat and humidity.
• Do not subject to strong physical shocks.
• The AC power adapter may hum or become hot to the touch
during use. This is normal.
• If the AC power adapter causes radio interference, reorient or
relocate the receiving antenna.
Electrical Interference
This device may interfere with hospital or aviation equipment.
Consult with hospital or airline sta before using the device in a
hospital or on an aircraft.
Liquid Crystal
In the event that the monitor is damaged, care should be taken to
avoid contact with liquid crystal. Take the urgent action indicated
should any of the following situations arise:
• If liquid crystal comes in contact with your skin, clean the area with a
cloth and then wash thoroughly with soap and running water.
• If liquid crystal enters your eyes, ush the a ected eye with clean
water for at least 15 minutes and then seek medical assistance.
• If liquid cr ystal is swallowed, rinse your mouth thoroughly with wa-
ter. Drink large quantities of water and induce vomiting, then
seek medical assistance.
Using the Device
NOTICES
To prevent re or shock hazard, do not expose the unit to rain or moisture.
Please read the “Safety Notes” (P iii) and make sure you understand them before using the device.
Perchlorate Material—special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate.
For Customers in the U.S.A.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
o and on, the user is encouraged to try to correct the inter ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di erent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modi cations not expressly approved in this manual could void the user’s authority to operate
the equipment.
Notes on the Grant
To comply with Part 15 of the FCC Rules, this product must be used with a FUJIFILM-speci ed ferrite-core A/V cable, USB cable, and
DC supply cord.
For Customers in Canada
CAUTION: This Class B digital apparatus complies with Canadian ICES-003.
iv
For Your Safety
EC Declaration of Conformity
Disposal of Electrical and Electronic Equipment in Private Households
In Countries Outside the European Union, Norway, Iceland and Liechtenstein
Notes on Copyright
Trademark Information
EC Declaration of Conformity
We
Name: FUJIFILM Electronic Imaging Europe GmbH
Address: Benzstrasse 2, 47533 Kleve, Germany
declare that the product
Product Name: FUJIFILM DIGITAL VIEWER FINEPIX REAL 3D V3
Manufacturer’s Name: FUJIFILM Corporation
Manufacturer’s Address: 7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052 JAPAN
conforms to the following Standards:
Safety: EN60950-1: 2006 + A11: 2009
EMC: EN55022: 2006 + A1: 2007 Class B
following the provision of the EMC Directive (2004/108/EC) and Low Voltage Directive (2006/95/EC).
Kleve, Germany October 1, 2011
Place Date Signature, Managing Director
Disposal of Electrical and Electronic Equipment in Private Households
Disposal of Used Electrical and Electronic Equipment (Applicable in the European Union, Norway, Iceland and Liechtenstein)
The recycling of materials will help to conserve natural resources. For more detailed information about recycling this product, please
contact your local city o ce, your household waste disposal service or the shop where you purchased the product.
In Countries Outside the European Union, Norway, Iceland and Liechtenstein
If you wish to discard this product, including the batteries or accumulators, please contact your local authorities and ask for the correct
way of disposal.
Notes on Copyright
Unless intended solely for personal use, images displayed on your digital viewer cannot be used in ways that infringe copyright laws
without the consent of the owner. Note that some restrictions apply to the photographing of stage performances, entertainments,
and exhibits, even when intended purely for personal use. Users are also asked to note that the transfer of storage devices containing
images or data protected under copyright laws is only permissible within the restrictions imposed by those copyright laws.
Trademark Information
xD-Picture Card is a trademark of FUJIFILM Corporation. Microsoft, Windows, the Windows logo, Windows 7, Windows Vista and the
Windows Vista logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
“Windows” is an abbreviation used in reference to the Microsoft Windows operating system. Adobe and Adobe Reader are either
trademarks or registered trademarks of Adobe Systems Incorporated in the U.S.A. and/or other countries. SD, miniSD, microSD, SDHC,
miniSDHC, and microSDHC are trademarks. The SDHC logo is a trademark of SD-3C, LLC. The HDMI logo is a trademark. All other trade
names mentioned in this manual are the trademarks or registered trademarks of their respective owners.
Note: The “Designed for Microsoft® Windows® XP” and “
driver.
EN55024: 1998 + A1: 2001 + A2: 2003
EN61000-3-2: 2006
EN61000-3-3: 2008
This symbol on the product, or in the manual and in the warranty, and/or on its packaging indicates that this product
shall not be treated as household waste. Instead it should be taken to an applicable collection point for the recycling
of electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
This symbol on the batteries or accumulators indicates that those batteries shall not be treated as household waste.
If your equipment contains easy removable batteries or accumulators please dispose these separately according to
your local requirements.
CERTIFIED FOR Windows Vista™” logos apply only to the viewer and viewer hardware
v
Table of Contents
Before You Begin
1
First Steps
5
Viewing Pictures
11
Other Options
17
Troubleshooting
23
Appendix
25
FUJIFILM Worldwide Network
27
Table of Contents
For Your Safety ........................................................ii
IMPORTANT SAFETY INSTRUCTIONS ..................ii
Safety Notes ..........................................................iii
NOTICES .................................................................iv
Before You Begin
Viewing 3D Images ...............................................1
Getting Started .......................................................2
Symbols and Conventions .................................2
Package Contents .................................................2
Parts of the Digital Viewer ..................................3
Parts of the Remote Control ..............................4
First Steps
Readying the Remote Control ..........................5
Replacing the Battery .......................................... 6
Adjusting the Stand ..............................................7
Turning the Viewer On .........................................8
Turning the Viewer O ........................................8
Basic Setup ...............................................................9
Viewing Pictures
External Storage Devices ................................. 11
SD/SDHC Memory Cards ................................. 11
USB Storage Devices......................................... 11
Displaying Selected Images ............................ 12
Slide Shows ........................................................... 14
Slide Show Options ........................................... 14
Viewing C Images ........................................... 15
Viewing Movies ................................................... 16
1
5
11
Other Options
The Clock Calendar ............................................ 17
Copying and Deleting Files ............................. 18
Deleting Files ...................................................... 18
Copying Files ....................................................... 18
The Setup Menu .................................................. 19
Setup Menu Options ........................................ 19
Connecting the Viewer to a Computer ....... 21
Connecting the Viewer to an HDMI Device
Troubleshooting
Troubleshooting ................................................. 23
Appendix
Speci cations ....................................................... 25
Movie Files ........................................................... 26
Storage Devices ................................................. 26
FUJIFILM Worldwide Network
17
... 22
23
25
27
vi
Before You Begin
Viewing 3D Images
CC Display
Before You Begin
Viewing 3D Images
The FinePix REAL 3D V3 displays C photographs taken
with cameras such as the FinePix REAL 3D W3 (P15). C
images are best viewed from a position directly in front of
the screen (or, if more than one person is present, slightly
to one side) at a distance of about 40 to 50 cm (1.3 to
1.6 ft).
R The optimal viewing distance varies from person to person,
and may change with changes in location and temperature.
This is not a malfunction.
Display
The FinePix REAL 3D V3 uses a lenticular display covered with
a sheet of small convex lenses that present di erent images to
each eye, allowing you to view pictures in 3D without using 3D
glasses. Flicker and cross-talk are reduced for a bright, easy-toview screen.
R When C photographs are viewed through a lenticular
sheet, the left eye sees only the left image and the right eye
only the right image, creating a C e ect.
Q Do not view C display if you have a history of photosensitive or other epilepsy, heart disease,
or have other existing, serious medical conditions.
Q Do not view C display if you are su ering from fatigue, insomnia, the a ects of alcohol, or
are pregnant.
Q Should you experience fatigue or discomfort while viewing C images, refrain from continued
viewing.
Q A ten-minute break is recommended about once every half hour while viewing C images, or
more frequently when using common blue and red anaglyph C glasses.
Q If C images on LCD appear double, then adjust the camera parallax.
Q C viewing is not recommended for young children (especially age six and under), because
their eyes may be very sensitive and C viewing may a ect the eye’s growth process. Children
should be supervised by parents or adult when viewing in C.
Q HDMI devices should be viewed from a distance equal to at least twice the width of the screen
to reduce the risk of adverse e ects on vision.
Q Individuals with notable di erences in vision between their two eyes may nd it di cult or
impossible to observe the C e ect unless corrective lenses are used.
Lenticular
sheet
LLLRRRRRLL
Before You Begin
1
Getting Started
✔✔ Table of Contents
................................
vi
Troubleshooting
................................
23
Symbols and Conventions
Package Contents
Compatible Storage Devices
Getting Started
Before using the FinePix REAL 3D V3 digital viewer, read the warnings (P ii) and take a
few minutes to familiarize yourself with the terms and conventions used in this manual.
For information on speci c topics, consult the sources below.
Table of Contents
The “Table of Contents” gives an overview
of the entire manual. The principal digital
viewer operations are listed here.
Symbols and Conventions
The following symbols are used in this manual:
Q This information should be read before use to ensure correct operation.
R Additional information that may be helpful when using the device.
P Other pages in this manual on which related information may be found.
Menus and other text in the display are shown in bold. In the illustrations in this manual,
the display may be simpli ed for explanatory purposes.
Package Contents
Before using the viewer con rm that the package contains these items:
................................PP
vi✔✔
Troubleshooting
Having a speci c problem with the digital
viewer? Find the answer here.
................................PP
23
FinePix REAL 3D V3
digital viewer
• USB cable
• Warranty
• Owner’s Manual (this manual)
Compatible Storage Devices
This product supports SD, SDHC, and USB storage devices (P26), referred to in this manual as
“storage devices.”
2
Remote control
(ships with battery installed)
AC power adapter
(shape varies with country or
region of sale)
Parts of the Digital Viewer
Part
P
Part
P
Parts of the Digital Viewer
Getting Started
Before You Begin
Part
1 Display —
2 Infrared receiver 5
3 Wall hooks 7
4 Stereo speakers —
g button 9
5
6 OK button 9
h button 9
7
8 BACK button 9
9 MENU button 10
10 Vents —
Q The cooling fan turns on automatically as required. The motor may be audible while the fan is
running.
P
11 Memory card slot 11
12 USB connector for storage devices 11
13 HDMI connector (type A) 22
14 Mini-B USB connector 21
15 Stand 7
16 Tripod mount 7
17 Brightness control 22
18 Power switch 8
19 Connector for AC power adapter 8
20 Cooling fan —
Part
P
3
Getting Started
Parts of the Remote Control
Part
P
Part
P
Parts of the Remote Control
Buttons with the same names as those on the digital viewer perform the same functions. Unless otherwise noted, the descriptions in this manual refer to the controls on
the remote.
Part
1
Q PARALLAX (R/S) buttons
2 SLIDE SHOW button 14
e button 9
3
g button 9
4
5 BACK button 9
6 ZOOM button 13
7 Battery holder 6
8 ROTATE button 13
P
15
9 VOLUME (
10 f button 9
11
12 OK button 9
13 3D/2D
14 MENU button 10
15
e/b) buttons 16
h button 9
g button 15
U (power) button 8
Part
P
4
First Steps
Readying the Remote Control
Using the Remote
First Steps
Readying the Remote Control
A battery is inserted in the remote control at shipment.
Before using the remote control, remove the plastic insulating sheet from the battery chamber.
R The battery supplied with the remote control is intended for
trial use only. Replace the battery (
does not function as expected.
Using the Remote
Point the remote at the infrared receiver on the digital viewer.
Approx. 3 m (9.8 ft)
or less
P6) if the remote control
First Steps
Insulating sheet
Infrared receiver
Maximum vertical and
horizontal angle approx. 30 °
5
Loading...