Fuji Electric PXR Instruction Manual

Instruction Manual

INP-TN512642a-E

MICRO CONTROLLER X
COMMUNICATION
FUNCTIONS
(RS-485 MODBUS)

TYPE: PXR

NOTICE

1. Exemption items from responsibility
The contents of this document may be changed in the future without prior notice.
We paid the utmost care for the accuracy of the contents. However, we are not liable for direct and

indirect damages resulting from incorrect descriptions, omission of information, and use of
information in this document.

－i－

CONTENTS

1. COMMUNICATION FUNCTIONS

･･･････････････････････････････････････････････････････････････

1

1.1 General

･･･････････････････････････････････････････････････････････････････････････････････

1

2. SPECIFICATIONS

････････････････････････････････････････････････････････････････････････････

2

2.1 Communication Specifications

･････････････････････････････････････････････････････････････････

2

3. CONNECTION

･･･････････････････････････････････････････････････････････････････････････････

3

3.1 Terminal Allocation

･････････････････････････････････････････････････････････････････････････

3

3.2 Wiring

････････････････････････････････････････････････････････････････････････････････････

4

4. SETTING OF COMMUNICATION CONDITION

････････････････････････････････････････････････････

5

4.1 Set Items

･･････････････････････････････････････････････････････････････････････････････････

5

4.2 Setting Operation Method

･････････････････････････････････････････････････････････････････････

6

5. MODBUS COMMUNICATION PROTOCOL

･･･････････････････････････････････････････････････････

7

5.1 General

･･･････････････････････････････････････････････････････････････････････････････････

7

5.2 Composition of Message

･･････････････････････････････････････････････････････････････････････

8

5.3 Response of Slave Station

････････････････････････････････････････････････････････････････････

10

5.4 Function Code

･････････････････････････････････････････････････････････････････････････････

11

5.5 Calculation of Error Check Code (CRC-16)

･･････････････････････････････････････････････････････

12

5.6 Transmission Control Procedure

･･･････････････････････････････････････････････････････････････

13

5.7 FIX Processing (Cautions at write-in of data)

････････････････････････････････････････････････････

15

6. DETAILS OF MESSAGE

･･････････････････････････････････････････････････････････････････････

16

6.1 Read-out of Bit Data ［Function code:01

H

］

････････････････････････････････････････････････････

16

6.2 Read-out of Read-out Only Bit Data [Function code:02

H

]

･････････････････････････････････････････････

17

6.3 Read-out of Word Data [Function code:03

H

]

････････････････････････････････････････････････････

19

6.4 Read-out of Read-out Only Word Data [Function code:04

H

]

･･････････････････････････････････････････

22

6.5 Write-in of Bit Data (1 bit) [Function code:05

H

]

･････････････････････････････････････････････････

24

6.6 Write-in of Word Data (1 word) [Function code:06

H

]

･･････････････････････････････････････････････

25

6.7 Write-in of Continuous Word Data [Function code:10

H

]

･･････････････････････････････････････････

26

7. ADDRESS MAP AND DATA FORMAT

･･････････････････････････････････････････････････････････

28

7.1 Data Format

･･････････････････････････････････････････････････････････････････････････････

28

7.2 Address Map of Internal Calculation Value Data

･･････････････････････････････････････････････････

31

7.3 Address Map of Engineering Unit Data

･････････････････････････････････････････････････････････

36

7.4 Additional Explanation of Address Map

････････････････････････････････････････････････････････

41

8. SAMPLE PROGRAM

･････････････････････････････････････････････････････････････････････････

44

9. TROUBLESHOOTING

････････････････････････････････････････････････････････････････････････

49

－1－

1. COMMUNICATION FUNCTIONS

1.1 General

• PXR provides a communication function by RS-485 interface, by which it can transmit and receive data to and

from host computer, programmable controller, graphic display panel, etc.

• The communication system consists of master station and slave stations. Up to 31 slave stations (PXR) can

be connected per master station.

Note that, because the master station can communicate with only one slave station at a time, a party to

communicate with must be specified by the "Station No." set at each slave station.

• In order that the master station and slave station can communicate, the format of the transmit/receive data must

coincide. For the PXR, the format of the communication data is determined by the MODBUS protocol.

• Please use an RS-232C↔RS-485 converter in case of designating a personal computer or other devices which

have an RS-232C interface as a master station.

[RS-232C↔RS-485 converter] (recommended article)

Type: KS-485 (non-isolated type)/SYSTEM SACOM Corp.
Type: SI-30A (isolated type)/SEKISUI ELECTRONICS Co., Ltd.

RS-485

RS-232C

Personal
computer

RS-232C  RS-485 converter

RS-485

Programmable
controller



[Note] MODBUS

®

is the registered trade mark of Gould Modicon.

－2－

2. SPECIFICATIONS

2.1 Communication Specifications

Item Specification
Electrical specification Based on EIA RS-485
Transmission system 2-wire, semi-duplicate
Synchronizing system Start-stop synchronous system
Connection format 1 : N
Number connectable units Up to 31 units
Transmission distance 500m max. (total extension distance)
Transmission speed 9600bps

Data length 8 bits
Stop bit 1 bit

Data format

Parity none, even, odd (selectable)
Transmission code HEX value (MODBUS RTU mode)
Error detection CRC-16
Isolation Functional isolation between transmission circuit

and others (withstand voltage : 500V AC)

－3－

3. CONNECTION

WARNING

For avoiding electric shock and malfunctions, do not turn on the power supply untill all wiring
have been completed.

3.1 Terminal Allocation

Terminal number Signal name

7 +
8 -

－4－

3.2 Wiring

• Use twisted pair cables with shield.

Recommended cable: UL2464, UL2448, etc.

• The total extension length of the cable is up to 500 m. A master station and up to 31 units of the PXR can be

connected per line.

• Both ends of the cable should be terminate with terminating resistors 100Ω1/2W.

• The shield wire of the cable should be grounded at one place on the master station unit side.

• If the PXR is to be installed where the level of noise applied to the PXR may exceed 1000 V, it is

recommended to install a noise filter in the master station side as below.

Recommended noise filter: ZRAC2203-11/TDK

Transmission

cable

RS-232C⇔RS-485

Noise filter PXR

Master station

（

PC, etc.

）

78＋

−

Slave station (PXR)

Twisted pair cable with shield

Terminating resistor
100Ω（1/2W）

RS-485 interface

or

  RS-485 side of the RS-232C RS-485 converter

Terminating resistor
100Ω（1/2W）

Master station side

FG

−

78＋

−

Slave station (PXR)

78＋

−

Slave station (PXR)

－5－

4.

SETTING OF COMMUNICATION CONDITION

In order that the master station and instrument (PXR) can correctly communicate, following settings are required.

• All communication condition settings of the master station are the same as those of instruments (PXR).

• All instruments (PXR) connected on a line are set to "Station Nos. (STno)" which are different from each other.

(Any "Station No." is not shared by more than one instrument.)

4.1 Set Items

The parameters to be set are shown in the following table. Set them by operating the front panel keys.

Parameter

symbol

Item

Value at
delivery

Setting range Remarks

―――

Transmission speed 9600bps Fixed (can not be changed)

―――

Data length 8 bits Fixed (can not be changed)

―――

Stop bit 1 bit Fixed (can not be changed)

CoM Parity setting 0

0: odd parity
1: even parity
2: none parity

Set the same
communication
condition to the master
station and all slave
stations.

STno Station No. 1

0 to 255

(0:communication function stop)

Set a different value to
each station.

－6－

4.2 Setting Operation Method

The following example shows how to set the communication conditions.

Example: Selecting an even parity and “STno=18” on a station.

Key

operation

Indication Description

200
200

Running state (PV/SV indication)

SEL
(6 seconds)

P-n1

0

Press the SEL key for approximately 6 seconds. P-n1 appears and

No. 3 block parameter is selected.

∨

STno

0

Operate the ∨ key repeatedly until STno parameter appears. (If

past over, operate the ∧ key to return.)

SEL

STno

0

Press the SEL key. The numeric value on the lower indicator

blinks and the setting mode is selected.

∧∨

STno

18

Operate the ∧ or ∨ key to change the numeric value to 18.

SEL

STno

18

Press the SEL key again. The numeric value stops blinking and

the setting is registered.

∨

CoM

0

Press the ∨ key to display the CoM parameter.

SEL

CoM

0

Press the SEL key. The numeric value on the lower indicator

blinks and the setting mode is selected.

∧∨

CoM

1

Operate the ∧ or ∨ key until the numeric value changes to 1 (even

parity).

SEL

CoM

1

Press the SEL key again. The numeric value stops blinking and

the setting is registered.

SEL
(3 seconds)

200
200

Press the SEL key for 3 seconds to resume the running indication

(PV/SV indication).

－7－

5. MODBUS COMMUNICATION PROTOCOL

5.1 General

The communication system by the MODBUS protocol is that the communication is always started from the master

station and a slave station responds to the received message.

Transmission procedures is as shown below.

1） The master station sends a command message to a slave station.
2） The slave station checks that the station No. in the received message matches with the own station No. or

not.

3） If matched, the slave station executes the command and sends back the response message.

4) If mismatched, the slave station leaves the command message and wait for the next command message.

a) In case when the station No. in the received command message matches with the own slave station No.

Command message

Response message

Slave to master

Master to slave

Data on

the line

b) In case when the station No. in the received command message mismatches with the own slave station

No.

Command message

(Not respond)

Slave to master

Master to slave

Data on

the line

The master station can individually communicate with any one of slave stations connected on the same line upon

setting the station No. in the command message.

－8－

5.2 Composition of Message

Command message and response message consist of 4 fields ; Station No., Function code, Data and Error check

code. And these are send in this order.

Station No. (1 byte)

Function code (1 byte)

Data (2 to 125 bytes)

Error check code (CRC-16) (2 bytes)

Fig. 5-1 Composition of message

In the following, each field is explained.

(1) Station No.

Station No. is the number specifiing a slave station. The command message is received and operated only by

the slave station whose station No. matches with the No. set in the parameter "STno".

For details of setting the parameter "STno", refer to chapter 4.

(2) Function code

This is a code to designate the function executed at a slave station.

For details, refer to section 5.4.

(3) Data

Data are the data required for executing function codes. The composition of data varies with function codes.

For details, refer to chapter 6.

A coil number or a register number is assigned to each data in the temperature controller. For reading/writing

the data by communication, designate the coil number or register number.

Note that the coil number or register number transmitted on message is expressed as its relative address.

The relative address is calculated by the following expression.

Relative address

＝













The lower 4 digits of the

Coil number or register number

– 1

For example, when the resister number designated by a function code is 40003,
Relative address = (lower 4 digits of 40003) – 1

= 0002

is used on the message.

－9－

(4) Error check code

This is the code to detect message errors (change in bit) in the signal transmission.

On the MODUBUS protocol (RTU mode), CRC-16 (Cycric Redundancy Check) is applied.

For CRC calculation method, refer to section 5.5.

－10－

5.3 Response of Slave Station

(1) Response for normal command

To a relevant message, the slave station creates and sends back a response message which corresponds to the

command message. The composition of message in this case is the same as in section 5.2.

Contents of the data field depend on the function code. For details, refer to Chapter 6.

(2) Response for abnormal command

If contents of a command message have an abnormality (for example, non-actual function code is designated)

other than transmission error, the slave station does not execute that command but creates and sends back a

response message at error detection.

The composition of response message at error detection is as shown in Fig. 5-2 The value used for function

code field is function code of command message plus 80

H

.

Table 5-1 gives error codes.

Station No.

Function code + 80H

Error code

Error check（CRC-16）

Fig. 5-2 Response message at error detection

Table 5-1 Error code

Error code Contents Description

01H Illegal function Non-actual function code is designated.

Check for the function code.

02H Illegal data address A relative address of a coil number or resister

number to which the designated function code can
not be used.

03H Illegal data value Because the designation of number is too much,

the area where coil numbers or resister numbers do
not exist is designated.

(3) No response

Under any of the following items, the slave station takes no action of the command message and sends back no

response.

・A station number transmitted in the command message differs from the station number specified to the

slave station.

・ A error check code is not matched, or a transmission error (parity error, etc.) is detected.
・ The time interval between the composition data of the message becomes longer than the time

corresponding to 24 bits. (Refer to section 5.6 Transmission Control Procedure)

・While the data is being written in non-volatile memory after write via communication, the next write is

attempted.

－11－

5.4 Function Code

According to MODBUS protocol, coil numbers and register numbers are assigned by function codes.

Each function code acts on specific coil number and register number.

This correspondence is shown in Table 5-2, and the message length by function is shown in Table 5-3.

Table 5-2 Correspondence between function codes and objective address

Function code

Coil No. and resister No.

No. Function Object

No. Contents

01H Read-out

(continuously)

Coil

0xxxx Read-out/write-in bit data

02H Read-out

(continuously)

Input relay

1xxxx Read-out bit data

03H Read-out

(continuously)

Holding register

4xxxx Read-out/write-in word data

04H Read-out

(continuously)

Input register

3xxxx Read-out word data

05H Write-in Coil

0xxxx Read-out/write-in bit data

06H Write-in Holding register

4xxxx Read-out/write-in word data

10H Write-in

(continuously)

Holding register

4xxxx Read-out/write-in word data

Table 5-3 Function code and message length

[Unit:byte]

Command message Response message

Function

code

Contents Number of

designatable

data

Minimum Maximum Minimum Maximum

01H Read-out of bit data 1bit

*1

8 8 6 6

02H Read-out of bit data (read-out only) 8 bits

*1

8 8 6 6

03H Read-out of word data 60 words

*1

8 8 7 125

04H Read-out of word data

(read-out only)

15 words

*1

8 8 7 35

05H Write-in of bit data 1 bit 8 8 8 8
06H Write-in of word data 1 word 8 8 8 8
10H Write-in of continuous word data 60 words

*1

11 129 8 8

*1) The "Number of designatable data" given above is the limit due to the number of data which the instrument

assigns to coil number and register number (except function codes 05

H

, 06H).

－12－

5.5 Calculation of Error Check Code (CRC-16)

CRC-16 is the 2-byte (16-bits) error check code. From the top of the message (station No.) to the end of the

data field are calculated.

The slave station calculates the CRC of the received message, and does not respond if the calculated CRC is

different from the contents of the received CRC code.

Fig. 5-3 shows the flow of the CRC-16 calculation system.

NO

NO

YES

YES

NO

YES

Start

Set 1 in J.

Set 1 in J.

Bit at right end

of CR is 1?

Shift CR to right by 1 bit, and A001H and
exclusive logical sum (XOR) are executed
and its result is set in CR.

Shift CR to righ

t

by 1 bit.

Add 1 to J.

Add 1 to J.

End

Explanation of variables

CR:CRC error check data (2 bytes)

I:Digits of calculation characters

in command message

J:Check on the number of times

of CR calculation

(Calculation is executed in the order of
command message station No., function
code and data.)

CR calculation result shall be added to
the last command message in the order
of LOW byte and HIGH byte.

Set FFFFH (hexadecimal number) in CR.

Calculation (8 times) is
finished?

J>8

Calculation of all characters is

completed?

I>All characters

Exclusive logical sum (XOR) is executed
with CR and one character (1 byte) of the I
characters, and its results is set in CR.

Fig. 5-3 Flow of CRC-16 calculation

－13－

5.6 Transmission Control Procedure

(1) Transmission procedure of master station

The master station must proceed to a communication upon conforming to the following items.

(1-1) Before sending a command message, provide 48 bits time or more vacant status.

(1-2) For sending, the interval between bytes of a command message is below 24 bits time.

(1-3) Within 24 bits time after sending a command message, the receiving status is posted.

(1-4) Provide 48 bits time or more vacant status between the end of response message reception and

beginning of next command message sending [same as in (1-1)].

(1-5) For ensuring the safety, make a confirmation of the response message and make an arrangement so

as to provide 3 or more retries in case of no response, error occurrence, etc.

Note) The above definition is for most unfavorable value. For ensuring the safety, it’s recommended the

program of the master to work with safety factors of 2 to 3. Concretely, it is advised to arrange the

program for 9600 bps with 10 ms or more for vacant status (1-1), and within 1 ms for byte interval (1-2)

and changeover from sending to receiving (1-3).

(2) Description

1) Detection of the message frame

Since the communication system uses the 2-wire RS-485 interface, there may be 2 statuses on a line below.

(a) Vacant status (no data on line)
(b) Communication status (data is existing)

Instruments connected on the line are initially at a receiving status and monitoring the line. When 24 bits

time or more vacant status has appeared on the line, the end of preceding frame is assumed and, within

following 24 bits time, a receiving status is posted. When data appears on the line, instruments receive it

while 24 bits time or more vacant status is detected again, and the end of that frame is assumed. I.e., data

which appeared on the line from the first 24 bits time or more vacant status to the next 24 bits time or more

vacant status is fetched as one frame.

Therefore, one frame (command message) must be sent upon confirming the following.

(1-1) 48 bits time or more vacant status precedes the command message sending.

(1-2) Interval between bytes of 1 command message is smaller than 24 bits time.

2) Response of this instrument (PXR)

After a frame detection (24 bits time or more vacant status), this instrument carries out processing with that

frame as a command message. If the command message is destined to the own station, a response

message is returned. Its processing time is 1 to 30 ms (depends on contents of command message).

After sending a command message, therefore, the master station must observe the following.

(1-3) Receiving status is posted within 24 bits time after sending a command message.

－14－

POL1 POL2

POL1 POL2 POL1 response data

POL1 response data

Space time of longer than 5ms is
needed
(longer than 10ms is recommended)

1 to 30msec

Master station → PXR

Master station ← PXR

Data on line

－15－

5.7 FIX Processing (Cautions at write-in of data)

The instrument is provided inside with a non-volatile memory (EEPROM) for holding the setting parameters.

Data written in the non-volatile memory is not lost even if turning off the power. When setting parameter is

written via communication, the data is stored in the internal memory (RAM) and then written in the non-volatile

memory.

FIX execution writes the parameters stored in the internal memory into the non-volatile memory, but this

function is not required any more because the data is written in non-volatile memory when it is written in the

parameter.

Fig. 5-4 shows the FIX procedure.

Cautions:

・ Write in the non-volatile memory takes approximately 5 seconds at the longest approximately 5 seconds.
・ While writing, do not turn off the power of the PXR. Otherwise, the data in the non-volatile memory will

be destroyed, whereby the PXR could not be used any longer.

・ The non-volatile memory (EEPROM) is a device where the number of write-in times is limited. The

guaranteed number of write-in times of the non-volatile memory used on the instrument is 10,000 minimum.

Therefore, limit the times of change of parameter setting to absolute minimum. Refrain from carrying out

the FIX processing periodically for example or while such is not absolutely required.

Start FIX

Read the FIX bit

with function code : 01

H

relative address : 0000

FIX=0?

Write ‘1’ into FIX bit

with function code : 05

H

relative address : 0000

H

Read the FIX bit

with function code : 01

H

relative address : 0000

H

FIX=0?

End FIX

No

Yes

No

Yes

Fig. 5-4 FIX procedure

－16－

6. DETAILS OF MESSAGE

6.1 Read-out of Bit Data ［Function code:01

H

］

Function code Max. bit number read-out in one message Relative data address Coil number

01H 1 bit 0000H 00001

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

00H Read-out start No.

(relative address)

00H

01

H

00H State of the first 8 bits

Read-out bit number

01

H

Upper

Upper

CRC data

Lower

CRC data

Lower

* Arrangement of read-out bit data

MSB LSB

0 0 0 0 0 0 0

State of read-out bit

(2) Function explanations

The state of the bit of the coil No. 00001 is read-out.

(3) Message transmission (example)

The following shows an example of reading-out the FIX execution request data from No. 1 slave station.
FIX execution request bit Relative address：0000

H

Number of data：01

H

Command message composition (byte) Response message composition (byte)
Station No.. 01

H

Station No. 01H

Function code 01H Function code 01H

Upper 00H Read-out byte number 01H Read-out start No.

(relative address)

Lower 00

H

State of the first 8 bits 00H

Upper 00H Upper 51H Read-out

bit number

Lower 01

H

CRC data

Lower 88H

Upper FDH

CRC data

Lower CA

H

* Meaning of read data

MSB LSB
State of FIX execution request 00H= 0 0 0 0 0 0 0 0

↑

No execution of FIX

－17－

6.2 Read-out of Read-out Only Bit Data [Function code:02H]

Function code Max. bit number read-out in one message Relative data address Coil number

02H 8 bits

0000

H

－000F

H

10001－10016

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

Upper Read-out start No.

(relative address)

Lower

01

H

00H State of the read-out bit

Read-out bit number

Lower 01

H

to 08 H Upper

Upper

CRC data

Lower

CRC data

Lower

* Arrangement of read-out bit data

MSB LSB

State of the first 1 bit

……

State of the last 1 bit

(2) Function explanations

Bit information data of continuous read-out bit number from the read-out start number.

Read-out bit data are arranged in 8-bit unit and transmitted from the slave station.

When read-out bit data number is not multiple of 8, all the bits (MSB side) not related with the state of the last

8 bits will become "0".

－18－

(3) Message transmission (example)

The following shows an example of reading-out the state of the alarm 1 and alarm 2 transmitted from No.31

slave station.

Alarm 1 detect data bit Relative address : 000C

H

Data number : 02H

Alarm 2 detect data bit Relative address : 000D

H

Command message composition (byte) Response message composition (byte)
Station No. 1F

H

Station No. 1FH

Function code 02H Function code 02H

Upper 00H Read-out byte number 01H Read-out start No.

(relative address)

Lower 0C

H

State of the first 8 bits 01H

Upper 00H Upper 66H Read-out

bit number

Lower 02

H

CRC data

Lower 60H

Upper 3AH

CRC data

Lower 76

H

* Meaning of read-out data

MSB LSB
State of alarm detection of 01

H

= 0 0 0 0 0 0 0 1

alarms 1 and 2

(

State of the first 2 bits)

Alarm 2 OFF state

Alarm 1 ON state

－19－

6.3 Read-out of Word Data [Function code:03H]

Function code Max. word number read-out

in one message

Relative data address Resister No. Kind of data

0000

H

－0070

H

40001－40113

Internal calculation value

03H 60 words

03E8

H

－0458

H

41001－41113

Engineering unit

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

Upper

Read-out byte number

Read-out word number×2

Read-out start
No.

(

relative address)

Lower

Upper

Upper

Contents of the
first word data

Lower

Read-out word
number

Lower







1 to 60

Upper

Upper

Contents of the
next word data

Lower

CRC data

Lower

Upper

Contents of
the last word
data

Lower

Upper

CRC data

Lower

* Arrangement of read-out word data

MSB LSB

Upper byte of contents of the first word data
Lower byte of contents of the first word data
Upper byte of contents of the next word data
Lower byte of contents of the next word data

Upper byte of contents of the last word data
Lower byte of contents of the last word data

(2) Function explanations

Word data of continuous word numbers from the read-out start No. can be read. Read-out word data are

transmitted from the slave station in the order of upper and lower bytes.

～ ～

～ ～

－20－

(3) Message transmission

(a) In case of data of internal calculation value

The following shows an example of reading the low and high limits of set value from No. 2 slave station.

Relative address of low limit of set value : 001E

H

Data number : 02H

Command message composition (byte) Response message composition (byte)
Station No. 02

H

Station No. 02H

Function code 03H Function code 03H

Upper 00H Read-out byte number 04H Read-out start No.

(relative address)

Lower 1EH Upper 00H
Upper 00H

Contents of the
first word data

Lower 00H Read-out word

number

Lower 02

H

Upper 27H

Upper A4H

Contents of the
next word data

Lower 10H

CRC data

Lower 3E

H

Upper D3H

CRC data

Lower 0FH

* Meaning of read-out data

Low limit of set value 00 00

H

= 10000（=100.00%FS）

(contents of first word data)

High limit of set value 27 10

H

= 10000（=100.00%FS）

(contents of next word data)

When input range is 0 to 400℃

Low limit of set value =400℃（=100.00%FS）
High limit of set value =400℃（=100.00%FS）

Point

For handling of the internal calculation value, engineering unit and decimal point,
refer to section 7.1.

－21－

(b) In case of data of engineering unit

The following shows an example of reading the low and high limits of set value from No. 2 slave station.

Relative address of low limit set value : 0406H Data number : 02H

Command message composition (byte) Response message composition (byte)
Station No. 02

H

Station No. 02H

Function code 03H Function code 03H

Upper 04H Read-out byte number 04H Read-out start No.

(relative address)

Lower 06H Upper 0H
Upper 00H

Contents of the
first word data

Lower 0H Read-out word

number

Lower 02H

Upper 01H

Upper 25H

Contents of the
next word data

Lower 90H

CRC data

Lower 09

H

Upper C8H

CRC data

Lower CFH

* Meaning of read-out data

Low limit of set value 00 00

H

= 100

(contents of first word data)

High limit of set value 01 90

H

= 400

(contents of next word data)

When the position of decimal point is 0 (Parameter P-dP=0),

Low limit of set value =400℃
High limit of set value =400℃

Point

For handling of the internal calculation value, engineering unit and decimal point,
refer to section 7.1.

－22－

6.4 Read-out of Read-out Only Word Data [Function code:04H]

Function code Max. word number read-out

in one message

Relative data address Resister No. Kind of data

0000

H

－000E

H

30001－30015

Internal calculation value

04H 15 words

03E8

H

－03F6

H

31001－31015

Engineering unit

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

Upper

Read-out byte number

Read-out word number×2

Read-out start No.
(relative address)

Lower Upper
Upper

Contents of the
first word data

Lower Read-out word

number

Lower







1 to 15

Upper

Upper

Contents of the
next word data

Lower

CRC data

Lower

Upper Contents of
the last word
data

Lower

Upper
CRC data

Lower

* Arrangement of read-out word data

MSB LSB

Upper byte of contents of the first word data
Lower byte of contents of the first word data
Upper byte of contents of the next word data
Lower byte of contents of the next word data

Upper byte of contents of the last word data
Lower byte of contents of the last word data

(2) Function explanations

Word data of continuous word numbers from the read-out start No. can be read. Read-out word data are

transmitted from the slave station in the order of upper and lower bytes.

～ ～

～

～

－23－

(3) Message transmission

(a) In case of data of internal calculation value

The following shows an example of reading-out the PV from No. 1 slave station.
Relative address of PV：0000

H

Data number：01H

Command message composition (byte) Response message composition (byte)
Station No. 01

H

Station No. 01H

Function code 04H Function code 04H

Upper 00H Read-out byte number 02H Read-out start No.

(relative address)

Lower 00

H

Upper 03H

Upper 00H

Contents of the
first word data

Lower 46H Read-out word

number

Lower 01H

Upper 38H

Upper 31H

CRC data

Lower 32H

CRC data

Lower CA

H

* Meaning of read-out data

Contents of the first word data 03 46

H

= 838（=8.38%FS）

When input range is 0-400℃,

PV=33.5℃（=8.38%FS×400

）

Input range

(b) In case of data of engineering unit

The following shows an example of reading-out the PV value from No. 1 slave station.
Relative address of PV value：03E8

H

Data number：01H

Command message composition (byte) Response message composition (byte)
Station No. 01

H

Station No. 01H

Function code 04H Function code 04H

Upper 03H Read-out byte number 02H Read-out start No.

(relative address)

Lower E8

H

Upper 01H

Upper 00H

Contents of the
first word data

Lower 4FH Read-out word

number

Lower 01H

Upper 38H

Upper B1H

CRC data

Lower 32H

CRC data

Lower BA

H

* Meaning of read-out data

Contents of the first word data 01 4F

H

= 335

When the position of decimal point is 1 (Parameter P-dP=1),

PV=33.5℃（=33.5）

Point

For handling of the internal calculation value, engineering unit and decimal point,
refer to section 7.1.

－24－

6.5 Write-in of Bit Data (1 bit) [Function code:05H]

Function code Max. bit number written-in one message Relative data address Coil No.

05H 1 bit 0000H 00001

This function has become unnecessary. (The customer can continue using the controller without changing the

program.)

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

00

H

00

H

Write-in designate
No.

(

relative address)

00

H

Write-in
designate No.

(

relative address)

00

H

Upper Upper State of write-in

designation

Lower







0000H=0
FF00

H

=1

State of write-in
designation

Lower







0000H=0
FF00

H

=1

Upper Upper

CRC data

Lower

CRC data

Lower

(2) Function explanations

Data of "0" or "1" is written in a bit of write-in designation No. bit. When "0" is written-in data of 0000H is

transmitted, and when "1" is written-in, data of FF00H is transmitted.

(3) Message transmission (example:This is the method of FIX execution)

The following shows an example of FIX execution request to No. 1 slave station.
FIX execution request bit Relative address：0000

H

Command message composition (byte) Response message composition (byte)
Station No. 01

H

Station No. 01H

Function code 05H Function code 05H

Upper 00H

Upper 00H

Write-in
designate No.

(

relative address)

Lower 00

H

Write-in
designate No.

(

relative address)

Lower 00

H

Upper FFH Upper FFH State of write-in

designation

Lower 00

H

State of write-in
designation

Lower 00H

Upper 8CH Upper 8CH

CRC data

Lower 3A

H

CRC data

Lower 3A

H

After receiving above command, it takes approximately 100ms to 5s seconds that PXR saves memory data

from RAM to EEPROM.

Caution

If you turn off the PXR during above saving (approximately 100ms to 5s), memory data are broken

and can not be used.

Point

For details of FIX processing, refer to section 5.7.

－25－

6.6 Write-in of Word Data (1 word) [Function code:06H]

Function code Max. word number write-in

in one message

Relative data address Resister No. Kind of data

0000

H

－0070

H

40001－40113

Internal calculation value

06H 1 words

03E8

H

－0458

H

41001－41113

Engineering unit

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

Upper

Upper

Write-in
designate No.

(

relative address)

Lower

Write-in
designate No.

(

relative address)

Lower

Upper Upper Write-in word

data

Lower

Write-in word
data

Lower

Upper Upper

CRC data

Lower

CRC data

Lower

(2) Function explanation

Designated word data is written in write-in designate No. Write-in data are transmitted from master station in

the order of upper and lower bytes.

(3) Message transmission (example)

The following shows an example of setting 100.0 (10000=C3E8H) to the parameter "P" of No.1 slave station.
Parameter "P" Relative address: 0005

H

(table of internal calculation unit)

(or 03ED

H

(table of engineering value))

* Parameter "P" is not in the engineering unit setting, the same value is

written in both tables.

Command message composition (byte) Response message composition (byte)
Station No. 01

H

Station No. 01H

Function code 06H Function code 06H

Upper 00H Upper 00H

Write-in
designate No.
(relative address)

Lower 05

H

In case of
interval
calculation

Write-in
designate No.
(relative address)

Lower 05

H

Upper 03H Upper 03H State of write-in

designation

Lower E8H

State of write-in
designation

Lower E8H

Upper 99H Upper 99H

CRC data

Lower 75

H

CRC data

Lower 75

H

Point

For handling of internal calculation value, engineering unit and decimal point, refer
to section 7.1.

Note!

1)While setting is being locked, response is returned normally, but the command is
not executed.

2)While the data is written in non-volatile memory, response is not returned.

－26－

6.7 Write-in of Continuous Word Data [Function code:10H]

Function code Max. word number write-in

in one message

Relative data address Resister No. Kind of data

0000

H

－0070

H

40001－40113

Internal calculation value

10H 60 words

03E8

H

－0458

H

41001－41113

Engineering unit

(1) Message composition

Command message composition (byte) Response message composition (byte)
Station No. Station No.
Function code Function code

Upper Upper Write-in start No.

(relative address)

Lower

Write-in start No.
(relative address)

Lower

Upper Upper Write-in word

number

Lower







1 to 60

Write-in word
number

Lower
Upper

Write-in byte number







Write-in word number×2

CRC data

Lower

Upper First write-in

word data

Lower
Upper Next write-in

word data

Lower

Upper Last write-in

word data

Lower
Upper

CRC data

Lower

* Arrangement of write-in word data

MSB LSB

Upper byte of contents of the first word data
Lower byte of contents of the first word data
Upper byte of contents of the next word data
Lower byte of contents of the next word data

Upper byte of contents of the last word data
Lower byte of contents of the last word data

(2) Function explanation

Word data of continuous word number is written from write-in start address. Write-in word data are

transmitted from master station in the order of upper and lower bytes.

～ ～

～ ～

－27－

(3) Message transmission (example)

The following shows an example of writing-in P=100.0, I=10, and D=5.0 to No. 1 slave station.

P=03E8

H

（=1000D）

I=0064

H

（=100D）

D=0032

H

（=50D）

Parameter "P" Relative address:0005

H

Data number:03

H

Command message composition (byte) Response message composition (byte)
Station No. 01

H

Station No. 01H

Function code 10H Function code 10H

Upper 00H Upper 00H

Write-in start No.

Lower 05

H

Write-in start No.

Lower 05H

Upper 00H Upper 00H Write-in word

number

Lower 03H

Write-in word
number

Lower 03H

Write-in byte number 06H Upper 90H

Upper 03H

CRC data

Lower 09H First write-in

word data

Lower E8

H

Upper 00H Next write-in

word data

Lower 64

H

Upper 00H Last write-in

word data

Lower 32H
Upper 56H

CRC data

Lower BE

H

Point

Since the transmission data can not include a decimal point, data of 100.0 is transmitted as

"1000".

For transmission format of each data, refer to the address map (Chapter 7).

－28－

7. ADDRESS MAP AND DATA FORMAT

7.1 Data Format

7.1.1 Transmission data format

The MODBUS protocol used in this instrument (PXR) is RTU (Remote Terminal Unit) mode.

Transmitted data is "numeric value" and not "ASCII code".

7.1.2 Internal calculation value and engineering unit

This instrument can handle 2 kinds of set value data or other data which are affected by input range as follows.

1) Internal calculation value : In % with respect to input range (0.00 to 100.00, without decimal point)

2) Engineering unit : Subjected to scaling to actual value according to input range

"Engineering unit" data can be handled with "Internal calculation value" address (register No.) plus 1,000

[Example] The value of "PV = 150" (input range: 0 to 400°C)

Register No. Data (HEX)

Data (decimal)
Internal
calculation value

30001 0EA6H

3750（37.50%）

Engineering unit 31001 0096H 150

In case of "Internal calculation value" here,

37.50 (%) × 400 (full scale) = 150 (°C) is obtained.

Note that the same data is handled at both addresses if it is not affected by input range.

This handling does not apply to bit data. (Address increased by 1,000 is invalid.)

For data affected by input range, refer to address maps in Sections 7.2 and 7.3.

Note : After changing the input range by communication write-in, pay attention to the decimal point position.

After changing the decimal point position by communication write-in, simultaneously change the lower

limit and upper limit of input range.

Example: Input range 0 to 400 changed into 0.0 to 400.0

a) Face panel operation:

P-dP=0→1 suffices

b) Communication write-in:

P-dP=0→1
P-SL=0→0
P-SU=400→4000







must be performed.

－29－

7.1.3 Handling of decimal point

Some internally stored data have more digits below decimal point than displayed on the face panel.

No decimal point is added to transmission data.

For data given in the following table, carry out an alignment of decimal point.

(a) Internal calculation value data (address map shown in Section 7.2)

Digits below point Kind Resister No.

Parameter [ P-SL ] 40018 Designate by
parameter [P-dP]
(0 to 2)

Parameter [ P-SU ] 40019

Parameter [ P ] 40006

Parameter [ i ] 40007

Parameter [ d ] 40008

Parameter [ CooL ] 40010

Parameter [ P-dF ] 40022

Parameter [ HB ] 40039

1 digit below point

Parameter [ CT ] 30010

Data affected by input range See address map (Section 7.2)

Parameter [ dB ] 40011

Parameter [ bAL ] 40013

Parameter [ PLC1 ] 40025

Parameter [ PHC1 ] 40026

Parameter [ PLC2 ] 40027

Parameter [ PHC2 ] 40028

Parameter [ OUT1 ] 30004

2 digits below point

Parameter [ OUT2 ] 30005

(b) Engineering unit (address map shown in Section 7.3)

Digits below point Kind Resister No.

Parameter [ P-SL ] 41018

Parameter [ P-SU ] 41019

Designate by
parameter [P-dP]
(0 to 2)

Data affected by input range See address map (Section 7.3)

Parameter [ P ] 41006

Parameter [ i ] 41007

Parameter [ d ] 41008

Parameter [ CooL ] 41010

Parameter [ P-dF ] 41022

Parameter [ HB ] 41039

1 digit below point

Parameter [ CT ] 31010

Parameter [ dB ] 41011

Parameter [ bAL ] 41013

Parameter [ PLC1 ] 41025

Parameter [ PHC1 ] 41026

Parameter [ PLC2 ] 41027

Parameter [ PHC2 ] 41028

Parameter [ OUT1 ] 31004

2 digits below point

Parameter [ OUT2 ] 31005

－30－

7.1.4 Data when input is abnormal

When "UUUU" or "LLLL" is displayed on the face panel on account of over-range, under-range or input open-

circuit for example, PV read-out value is 105% or -5% of input range.

Presence of any input abnormality via communication can be detected by:

"Register No. 30008 (or 31008): Input/main unit abnormal status"

－31－

7.2 Address Map of Internal Calculation Value Data

Data affected by input range is handled in terms of internal value (0.00 to 100.00% value) before

scaling.

For detailed contents about individual parameter function or setting range, refer to the operation manual

(ECNO: 406).

Bit data [read-out/write-in] : Function code [01

H

, 05H]

Relative

address

Coil No. Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

0000H 00001 Bit

Write in non-volatile memory
(FIX execution)

0:Not writing-in
1:Writing in memory

0:No request
1:Request to write in

(the same
function as

40001)

Bit data [read-out only] : Function code [02

H

]

Relative

address

Coil No. Type Memory contents Read-out data

Affected by

input range

Remarks or

corresponding

parameter

0000H 10001 Bit Alarm 1 ON/OFF

0:Alarm 1 OFF，1: Alarm 1 ON

0001H 10002 (Reserve)
0002H 10003 (Reserve)
0003H 10004 (Reserve)
0004H 10005 Bit Alarm 2 ON/OFF

0: Alarm 2 OFF，1: Alarm 2 ON

0005H 10006 (Reserve)
0006H 10007 (Reserve)
0007H 10008 (Reserve)

0008H 10009 Bit

Alarm 1 output
(Calculation result of non­exciting alarm)

0: Relay output of alarm 1 OFF
1: Relay output of alarm 1 ON

0009H 10010 Bit

Alarm 2 output
(Calculation result of non­exciting alarm)

0: Relay output of alarm 2 OFF
1: Relay output of alarm 2 ON

000AH 10011 (Reserve)

000BH 10012 Bit HB alarm relay output

0: HB alarm output OFF
1: HB alarm output ON

000CH 10013 Bit Alarm 1 ON/OFF

0: Alarm 1 OFF，1: Alarm 1 ON

(Same as 10001)

000DH 10014 Bit Alarm 2 ON/OFF

0: Alarm 2 OFF，1: Alarm 2 ON

(Same as 10002)

000EH 10015 (Reserve)

000FH 10016 Bit HB alarm relay output

0:HB alarm output OFF
1:HB alarm output ON

(Same as 10012)

－32－

Word data [read-out/write-in] : Function code [03

H

, 06H, 10H]

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

0000H 40001 Word Non-volatile memory write-in

0: Not writing-in
1: Writing in memory

0:No request
1:Request to write in

(Same function
as 00001)

0001H 40002 Word PID/FUZZY/SELF selection

0:PID control
1:FUZZYcontrol
2:SELF tuning control

CTrL
* Inhibit change

while
controlling

0002H 40003 Word SV value set on face panel

0 to 10000
(within 0.00 to 100.00% FS within set
value limits)

*

0003H 40004 Word Control RUN/standby

0: Invalidate standby (RUN)
1:Validate standby

STby

0004H 40005 Word Auto tuning command

0: Auto tuning

disabled

1: While executing

standard type AT
executed

2: While executing

low PV type AT
executed

0: Disable auto

tuning

1: Request

execution of
standard type

2: Request

execution of low
PV type AT

AT

0005H 40006 Word P

0 to 9999（0.0 to 999.9%）

P

0006H 40007 Word I

0 to 32000（0 to 3200.0 sec）

i

0007H 40008 Word D

0 to 9999（0.0 to 999.9 sec）

D

0008H 40009 Word

Hysteresis range at
two-position control

0 to 5000（0.00 to 50.00%FS） *

HyS

0009H 40010 Word COOL

0 to 1000（0.0 to 100.0）

CooL

000AH 40011 Word Dead band

-5000 to 5000（-50.00 to +50.00）

db

000BH 40012 Word Anti-reset windup

0 to 10000（0.00 to 100.00%） *

Ar

000CH 40013 Word Output convergence value

-10000 to 10000
（-100.00 to 100.00%）

bAL

000DH 40014 Word PV shift

-1000 to 1000（-10.00 to 10.00%FS） *

PVOF

000EH 40015 Word SV offset

-5000 to 5000（-50.00 to 50.00%FS） *

SVOF

000FH 40016 Word Input type code 0 to 16

P-n2

0010H 40017 Word Temperature unit

0:℃ 1:°F

P-F

0011H 40018 Word Input scale lower limit -1999 to 9999

P-SL

0012H 40019 Word Input scale upper limit -1999 to 9999

P-SU

0013H 40020 Word Decimal point place 0 to 2

P-dP
0014H 40021 (Do not use)
0015H 40022 Word Input filter time constant

0 to 9000（0.0 to 900.0 sec）

P-dF

0016H 40023 Word RCJ yes/no

0: Disable RCJ compensation

(do not perform reference cold junction
compensation)

1: Enable RCJ compensation (perform

reference cold junction compensation)

rCJ

0017H 40024 Word MV limit kind 0 to 15

PCUT
0018H 40025 Word Output 1 lower limit

-300 to 10300（-3.00 to 103.00%）

PLC1
0019H 40026 Word Output 1 upper limit

-300 to 10300（-3.00 to 103.00%）

PHC1

001AH 40027 Word Output 2 lower limit

-300 to 10300（-3.00 to 103.00%）

PLC2

001BH 40028 Word Output 2 upper limit

-300 to 10300（-3.00 to 103.00%）

PHC2

001CH 40029 (Do not use)
001DH 40030 (Do not use)
001EH 40031 Word Set value (SV) lower limit

0 to 10000（0.00 to 100.00%FS） *

SV-L
001FH 40032 Word Set value (SV) upper limit

0 to 10000（0.00 to 100.00%FS） *

SV-H
0020H 40033 (Do not use)
0021H 40034 (Do not use)
0022H 40035 (Do not use)
0023H 40036 (Do not use)
0024H 40037 (Do not use)
0025H 40038 (Do not use)
0026H 40039 Word Heater burnout alarm set value

0 to 500（0.0 to 50.0A）

Hb
0027H 40040 Word Setting lock 0 to 5

LoC

－33－

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

0028H 40041 Word Alarm 1 type 0 to 34

ALM1

0029H 40042 Word Alarm 2 type 0 to 34

ALM2

002AH 40043 (Do not use)

002BH 40044 Word

Alarm 1 set value or
alarm 1 lower limit set value

*

AL1 or A1-L

002CH 40045 Word

Alarm 2 set value or
alarm 2 lower limit set value

For absolute value alarm

0 to 10000（0.00 to 100.00%FS）

For deviation alarm

-10000 to 10000

（-100.00 to 100.00%FS）

*

AL2 or A2-L

002DH 40046 (Do not use)

002EH 40047 Word Alarm 1 upper limit set value

*

A1-H

002FH 40048 Word Alarm 2 upper limit set value

For absolute value alarm

0 to 10000（0.00 to 100.00%FS）

For deviation alarm

-10000 to 10000

（-100.00 to 100.00%FS）

*

A2-H

0030H 40049 (Do not use)
0031H 40050 Word Alarm 1 hysteresis

0 to 5000（0.00 to 50.00%FS） *

A1hy

0032H 40051 Word Alarm 2 hysteresis

0 to 5000（0.00 to 50.00%FS） *

A2hy
0033H 40052 (Do not use)
0034H 40053 Word Alarm 1 ON-delay set value

0 to 9999（0 to 9999 sec）

dLy1
0035H 40054 Word Alarm 2 ON-delay set value

0 to 9999（0 to 9999 sec）

dLy2
0036H 40055 (Do not use)
0037H 40056 (Do not use)
0038H 40057 Word Ramp/soak No. 1 target value

*

Sv-1
0039H 40058 Word Ramp/soak No. 2 target value

*

Sv-2

003AH 40059 Word Ramp/soak No. 3 target value

*

Sv-3

003BH 40060 Word Ramp/soak No. 4 target value

*

Sv-4

003CH 40061 Word Ramp/soak No. 5 target value

*

Sv-5

003DH 40062 Word Ramp/soak No. 6 target value

*

Sv-6

003EH 40063 Word Ramp/soak No. 7 target value

*

Sv-7
003FH 40064 Word Ramp/soak No. 8 target value

0 to 10000
(0.00 to 100.00%FS，
within set value limit)

*

Sv-8
0040H 40065 Word Ramp/soak No. 1 ramp time

TM1r
0041H 40066 Word Ramp/soak No. 1 soak time

TM1S
0042H 40067 Word Ramp/soak No. 2 ramp time

TM2r
0043H 40068 Word Ramp/soak No. 2 soak time

TM2S
0044H 40069 Word Ramp/soak No. 3 ramp time

TM3r
0045H 40070 Word Ramp/soak No. 3 soak time

TM3S
0046H 40071 Word Ramp/soak No. 4 ramp time

TM4r
0047H 40072 Word Ramp/soak No. 4 soak time

TM4S
0048H 40073 Word Ramp/soak No. 5 ramp time

TM5r
0049H 40074 Word Ramp/soak No. 5 soak time

TM5S

004AH 40075 Word Ramp/soak No. 6 ramp time

TM6r

004BH 40076 Word Ramp/soak No. 6 soak time

TM6S

004CH 40077 Word Ramp/soak No. 7 ramp time

TM7r

004DH 40078 Word Ramp/soak No. 7 soak time

TM7S

004EH 40079 Word Ramp/soak No. 8 ramp time

TM8r
004FH 40080 Word Ramp/soak No. 8 soak time

0 to 5999（0 to 5999 min）
* With main unit parameter,

Hour Minute

is displayed and set.
Therefore, correspondence occurs as:
3601:Data via communication
∥
6001:Display/setting on main unit

TM8S
0050H 40081 Word Ramp/soak mode 0 to 15

MOD

0051H 40082 Word Ramp/soak command

0: oFF

Ramp/soak stopped

1: rUn

Ramp/soak operated

2: HLd

Ramp/soak halted

3: End

Ramp/soak ended

0:oFF

Stop ramp/soak

1:rUn

Start ramp/soak

2:HLd

Halt ramp/soak

3: End ランプ

ソーク終了

ProG

－34－

Note

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

0052H 40083 Word Ramp/soak pattern selection

0: Execute No. 1 to 4 ramp/soak

（PTn=1）

1: Execute No. 5 to 8 ramp/soak

（PTn=2）

2: Execute No. 1 to 8 ramp/soak

（PTn=3）

PTn

0053H 40084 (Do not use)
0054H 40085 Word PV stable range

0 to 10000（0.00 to 100.00%FS） *

SLFb

0055H 40086 (Do not use)

0056H 40087 Word

Communication DI action
request

*② (refer to section 7.4.)

0057H 40088 Word Control action type code 0 to 19

P-n1

0058H 40089 Word

Output proportional cycle
(output 1)

0: Current output type
1 to 150（1 to 150 sec）:

Relay, SSR drive output type

TC

0059H 40090 Word

Output proportional cycle
(output 2)

1 to 150（1 to 150 sec）

TC2

005AH 40091 (Do not use)
005BH 40092 Word Alarm 1 option function

0 to 7（binary data 000B to 111

B

）

A1op

005CH 40093 Word Alarm 2 option function

0 to 7（binary data 000B to 111

B

）

A2op
005DH 40094 (Do not use)
005EH 40095 Word DI1 action setting 0 to 12

di-1

005FH 40096 (Do not use)

0060H 40097 Word Hysteresis mode setting

0: off (main unit parameter setting)
1: on (main unit parameter setting)

ONOF

0061H 40098 Word (Do not use)

0062H 40099 Word User zero adjustment

-5000 to 5000

（-50.00 to 50.00%FS）

*

ADJ0

0063H 40100 Word User span adjustment

-5000 to 5000

（-50.00 to 50.00%FS）

*

ADJS

0064H 40101 Word

DSP1
(parameter mask designation)

0 to 255

dSP1

0065H 40102 Word

DSP2
(parameter mask designation)

0 to 255

dSP2

0066H 40103 Word

DSP3
(parameter mask designation)

0 to 255

dSP3

0067H 40104 Word

DSP4
(parameter mask designation)

0 to 255

dSP4

0068H 40105 Word

DSP5
(parameter mask designation)

0 to 255

dSP5

0069H 40106 Word

DSP6
(parameter mask designation)

0 to 255

dSP6

006AH 40107 Word

DSP7
(parameter mask designation)

0 to 255

dSP7

006BH 40108 Word

DSP8
(parameter mask designation)

0 to 255

dSP8

006CH 40109 Word

DSP9
(parameter mask designation)

0 to 255

dSP9

006DH 40110 Word

DSP10
(parameter mask designation)

0 to 255

dSP10

006EH 40111 Word

DSP11
(parameter mask designation)

0 to 255

dSP11

006FH 40112 Word

DSP12
(parameter mask designation)

0 to 255

dSP12

0070H 40113 Word

DSP13
(parameter mask designation)

0 to 255

dSP13

Note） Read-out/write-in data from Resister No. 40083 (ramp/soak pattern selection) correspond to parameter “PTn”

to be displayed as shown below:

Read-out/write-in data Parameter PTn Contents

0 1 1 to 4 ramp/soak executed
1 2 5 to 8 ramp/soak executed
2 3 1 to 8 ramp/soak executed

－35－

Word data (read-out only) : Function code [04

H

]

Relative

address

Resister

No.

Type Memory contents

Read-out data

Affected by

input range

Remarks or

corresponding

parameter

0000H 30001 Word Process value (PV)

0 to 10000（0.00 to 100.00%FS） *

(Displayed PV
value)

0001H 30002 Word Currently used set value (SV)

0 to 10000（0.00 to 100.00%FS） *

(Displayed SV
value)

0002H 30003 Word Currently used deviation (DV)

-10000 to 10000

（-100.00 to 100.00%FS）

*

0003H 30004 Word MV (output 1)

-300 to 10300（-3.00 to 103.00%）

OUT1

0004H 30005 Word MV (output 2)

-300 to 10300（-3.00 to 103.00%）

OUT2

0005H 30006 Word Station No. 0 to 255

STno

0006H 30007 Word Alarm status

*③ (refer to Section 7.4.)

0007H 30008 Word Input/main unit abnormal status

*④ (refer to Section 7.4.)

0008H 30009 Word

Ramp/soak current running
position

0 to 17
*⑥ (refer to Section 7.4.)

STAT

0009H 30010 Word Heater current

0 to 500（0.0 to 50.0A）

CT

000AH 30011 Word Timer 1 current count

0 to 9999（0 to 9999 sec）

TM-1

000BH 30012 Word Timer 2 current count

0 to 9999（0 to 9999 sec）

TM-2
000CH 30013 (Reserve)
000DH 30014 (Reserve)
000EH 30015 Word DI action status

*⑤ (refer to Section 7.4.)

Notes)

• For details of *

②

to * ⑥ in the table, refer to Section 7.4.

• The area marked (Do not use) is a reserve area. Do not write in there.

• Register numbers 30002 (currently used SV) and 40003 (face panel set SV) do not become the same

value while switching-SV is active or ramp/soak is under way. (Example: While SV-1 is selected, the

value of SV-1 is read out of register number 30002.) For reading out SV for monitoring, use SV in

register number 30002.

－36－

7.3 Address Map of Engineering Unit Data

Data affected by input range is handled in terms of a value (engineering unit) after scaling.

For detailed contents about individual parameter function or setting range, refer to the operation manual

(ECNO: 406).

Bit data [read-out/write-in] : Function code [01

H

, 05H]

Relative

address

Coil No. Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

0000H 00001 Bit

Write in non-volatile memory
(FIX execution)

0:Not Writing-in
1:Writing in memory

0:No request
1:Write-in request

(the same
function as

40001)

Bit data [read-out only] : Function code [02

H

]

Relative

address

Coil No. Type Memory contents Read-out data

Affected by

input range

Remarks or

corresponding

parameter

0000H 10001 Bit Alarm 1 ON/OFF

0:Alarm 1 OFF，1: Alarm 1 ON

0001H 10002 (Reserve)
0002H 10003 (Reserve)
0003H 10004 (Reserve)
0004H 10005 Bit Alarm 2 ON/OFF

0: Alarm 2 OFF，1: Alarm 2 ON

0005H 10006 (Reserve)
0006H 10007 (Reserve)
0007H 10008 (Reserve)

0008H 10009 Bit

Alarm 1 output
(Calculation result of non­exciting alarm)

0: Relay output of alarm 1 OFF
1: Relay output of alarm 1 ON

0009H 10010 Bit

Alarm 2 output
(Calculation result of non­exciting alarm)

0: Relay output of alarm 2 OFF
1: Relay output of alarm 2 ON

000AH 10011 (Reserve)

000BH 10012 Bit HB alarm relay output

0: HB alarm output OFF
1: HB alarm output ON

000CH 10013 Bit Alarm 1 ON/OFF

0: Alarm 1 OFF，1: Alarm 1 ON

(Same as 10001)

000DH 10014 Bit Alarm 2 ON/OFF

0: Alarm 2 OFF，1: Alarm 2 ON

(Same as 10002)

000EH 10015 (Reserve)

000FH 10016 Bit HB alarm relay output

0:HB alarm output OFF
1:HB alarm output ON

(Same as 10012)

－37－

Word data [read-out/write-in]: Function code [03

H

, 06H, 10H]

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

03E8H 41001 Word

Non-volatile memory write-in
(FIX execution)

0: Not writing in
1: Write in memory

0:No request
1:Request to write in

(Same function

as 00001)

03E9 H 41002 Word PID/FUZZY/SELF selection

0:PID control
1:FUZZYcontrol
2:SELF tuning control

CTrL

* Inhibit change

while
controlling

03EA H 41003 Word SV value controlled on face panel -1999 to 9999 (within set value limits)

*

03EB H 41004 Word Control RUN/standby

0: Invalidate standby (RUN)
1:Validate standby

STby

03EC H 41005 Word Auto tuning command

0: Auto tuning

disabled

1: While executing

standard type AT
executed

2: While executing

low PV type AT
executed

0: Disable auto

tuning

1: Request

execution of
standard type

2: Request

execution of low
PV type AT

AT

03ED H 41006 Word P

0 to 9999（0.0 to 999.9%）

P

03EE H 41007 Word I

0 to 32000（0 to 3200.0 sec）

i
03EF H 41008 Word D

0 to 9999（0.0 to 999.9 sec）

D

03F0 H 41009 Word

Hysteresis range at
two-position control

0 to 9999 (0 to 50% value of input scale） *

HyS

03F1H 41010 Word COOL

0 to 1000（0.0 to 100.0）

CooL

03F2H 41011 Word Dead band

-5000 to 5000
(-50.00 to +50.00%）

db

03F3H 41012 Word Anti-reset windup

-1999 to 9999
(0 to 100% value of input scale）

*

Ar

03F4H 41013 Word Output convergence value

-10000 to 10000
（-100.00 to 100.00%）

bAL

03F5H 41014 Word PV shift

-1999 to 9999
(-10 to 10% value of input scale）

*

PVOF

03F6H 41015 Word SV offset

-1999 to 9999
(-50 to 50% value of input scale）

*

SVOF

03F7H 41016 Word Input type code 0 to 16

P-n2

03F8H 41017 Word Temperature unit

0:℃ 1:°F

P-F

03F9H 41018 Word Input scale lower limit -1999 to 9999

P-SL
03FAH 41019 Word Input scale upper limit -1999 to 9999

P-SU
03FBH 41020 Word Decimal point place 0 to 2

P-dP
03FCH 41021 (Do not use)
03FDH 41022 Word Input filter time constant

0 to 9000（0.0 to 900.0 sec）

P-dF

03FEH 41023 Word RCJ yes/no

0: Disable RCJ compensation

(do not perform reference cold junction
compensation)

1: Enable RCJ compensation (perform

reference cold junction compensation)

rCJ

03FFH 41024 Word MV limit kind 0 to 15

PCUT

0400H 41025 Word Output 1 lower limit

-300 to 10300（-3.00 to 103.00%）

PLC1

0401H 41026 Word Output 1 upper limit

-300 to 10300（-3.00 to 103.00%）

PHC1

0402H 41027 Word Output 2 lower limit

-300 to 10300（-3.00 to 103.00%）

PLC2

0403H 41028 Word Output 2 upper limit

-300 to 10300（-3.00 to 103.00%）

PHC2

0404H 41029 (Do not use)
0405H 41030 (Do not use)
0406H 41031 Word Set value (SV) lower limit

-1999 to 9999（within input scale） *

SV-L

0407H 41032 Word Set value (SV) upper limit

-1999 to 9999（within input scale） *

SV-H

0408H 41033 (Do not use)

0409H 41034 (Do not use)
040AH 41035 (Do not use)
040BH 41036 (Do not use)
040CH 41037 (Do not use)
040DH 41038 (Do not use)
040EH 41039 Word Heater burnout alarm set value

0 to 500（0.0 to 50.0A）

Hb

－38－

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data
setting range

Affected by

input range

Remarks or

corresponding

parameter

040FH 41040 Word Setting lock 0 to 5

LoC

0410H 41041 Word Alarm 1 type 0 to 34

ALM1

0411H 41042 Word Alarm 2 type 0 to 34

ALM2

0412H 41043 (Do not use)

0413H 41044 Word

Alarm 1 set value or
alarm 1 lower limit set value

*

AL1 or A1-L

0414H 41045 Word

Alarm 2 set value or
alarm 2 lower limit set value

-1999 to 9999
For absolute value alarm:

0 to 100% value of input scale

For deviation alarm:

–100 to 100% value of input scale

*

AL2 or A2-L

0415H 41046 (Do not use)

0416H 41047 Word Alarm 1 upper limit set value

*

A1-H

0417H 41048 Word Alarm 2 upper limit set value

-1999 to 9999
For absolute value alarm:

0 to 100% value of input scale

For deviation alarm:

–100 to 100% value of input scale

*

A2-H

0418H 41049 (Do not use)

0419H 41050 Word Alarm 1 hysteresis

0 to 9999
(0 to 50% value of input scale)

*

A1hy

041AH 41051 Word Alarm 2 hysteresis

0 to 9999
(0 to 50% value of input scale)

*

A2hy

041BH 41052 (Do not use)
041CH 41053 Word Alarm 1 ON-delay set value

0 to 9999（0 to 9999 sec）

dLy1

041DH 41054 Word Alarm 2 ON-delay set value

0 to 9999（0 to 9999 sec）

dLy2

041EH 41055 (Do not use)

041FH 41056 (Do not use)
0420H 41057 Word Ramp/soak No. 1 target value

*

Sv-1

0421H 41058 Word Ramp/soak No. 2 target value

*

Sv-2

0422H 41059 Word Ramp/soak No. 3 target value

*

Sv-3

0423H 41060 Word Ramp/soak No. 4 target value

*

Sv-4

0424H 41061 Word Ramp/soak No. 5 target value

*

Sv-5

0425H 41062 Word Ramp/soak No. 6 target value

*

Sv-6

0426H 41063 Word Ramp/soak No. 7 target value

*

Sv-7

0427H 41064 Word Ramp/soak No. 8 target value

-1999 to 9999
(within set value limit)

*

Sv-8

0428H 41065 Word Ramp/soak No. 1 ramp time

TM1r

0429H 41066 Word Ramp/soak No. 1 soak time

TM1S

042AH 41067 Word Ramp/soak No. 2 ramp time

TM2r

042BH 41068 Word Ramp/soak No. 2 soak time

TM2S

042CH 41069 Word Ramp/soak No. 3 ramp time

TM3r

042DH 41070 Word Ramp/soak No. 3 soak time

TM3S

042EH 41071 Word Ramp/soak No. 4 ramp time

TM4r

042FH 41072 Word Ramp/soak No. 4 soak time

TM4S

0430H 41073 Word Ramp/soak No. 5 ramp time

TM5r

0431H 41074 Word Ramp/soak No. 5 soak time

TM5S

0432H 41075 Word Ramp/soak No. 6 ramp time

TM6r

0433H 41076 Word Ramp/soak No. 6 soak time

TM6S

0434H 41077 Word Ramp/soak No. 7 ramp time

TM7r

0435H 41078 Word Ramp/soak No. 7 soak time

TM7S

0436H 41079 Word Ramp/soak No. 8 ramp time

TM8r

0437H 41080 Word Ramp/soak No. 8 soak time

0 to 5999（0 to 5999 min）
* With main unit parameter,

Hour Minute

is displayed and set.
Therefore, correspondence occurs as:
3601:Data via communication
∥
6001:Display/setting on main unit

TM8S

0438H 41081 Word Ramp/soak mode 0 to 15

MOD

0439H 41082 Word Ramp/soak command

0: oFF

Ramp/soak stopped

1: rUn

Ramp/soak operated

2: HLd

Ramp/soak halted

3: End

Ramp/soak ended

0:oFF

Stop ramp/soak

1:rUn

Start ramp/soak

2:HLd

Halt ramp/soak

3: End ランプ

ソーク終了

ProG

－39－

Note

Relative

address

Resister

No.

Type Memory contents Read-out data

Write-in data

setting range

Affected by

input range

Remarks or

corresponding

parameter

043AH 41083 Word Ramp/soak pattern selection

0: Execute No. 1 to 4 ramp/soak
1: Execute No. 5 to 8 ramp/soak
2: Execute No. 1 to 8 ramp/soak

PTn

043BH 41084 (Do not use)
043CH 41085 Word PV stable range -1999 to 9999 (Within input scale)

*

SLFb

043DH 41086 (Do not use)

043EH 41087 Word

Communication DI action
request

*② (refer to section 7.4.)

043FH 41088 Word Control action type code 0 to 19

P-n1

0440H 41089 Word

Output proportional cycle
(output 1)

0: Current output type
1 to 150（1 to 150 sec）:

Relay, SSR drive output type

TC

0441H 41090 Word

Output proportional cycle
(output 2)

1 to 150（1 to 150 sec）

TC2

0442H 41091 (Do not use)
0443H 41092 Word Alarm 1 option function

0 to 7（binary data 000B to 111

B

）

A1op

0444H 41093 Word Alarm 2 option function

0 to 7（binary data 000B to 111

B

）

A2op
0445H 41094 (Do not use)
0446H 41095 Word DI1 action setting 0 to 12

di-1
0447H 41096 (Do not use)

0448H 41097 Word Hysteresis mode setting

0: off (main unit parameter setting)
1: on (main unit parameter setting)

ONOF

0449H 41098 Word (Do not use)

044AH 41099 Word User zero adjustment

-1999 to 9999

（-50 to 50% value of input scale）

*

ADJ0

044BH 41100 Word User span adjustment

-1999 to 9999

（-50 to 50% value of input scale）

*

ADJS

044CH 41101 Word

DSP1
(parameter mask designation)

0 to 255

dSP1

044DH 41102 Word

DSP2
(parameter mask designation)

0 to 255

dSP2

044EH 41103 Word

DSP3
(parameter mask designation)

0 to 255

dSP3

044FH 41104 Word

DSP4
(parameter mask designation)

0 to 255

dSP4

0450H 41105 Word

DSP5
(parameter mask designation)

0 to 255

dSP5

0451H 41106 Word

DSP6
(parameter mask designation)

0 to 255

dSP6

0452H 41107 Word

DSP7
(parameter mask designation)

0 to 255

dSP7

0453H 41108 Word

DSP8
(parameter mask designation)

0 to 255

dSP8

0454H 41109 Word

DSP9
(parameter mask designation)

0 to 255

dSP9

0455H 41110 Word

DSP10
(parameter mask designation)

0 to 255

dSP10

0456H 41111 Word

DSP11
(parameter mask designation)

0 to 255

dSP11

0457H 41112 Word

DSP12
(parameter mask designation)

0 to 255

dSP12

0458H 41113 Word

DSP13
(parameter mask designation)

0 to 255

dSP13

Note） Read-out/write-in data from Resister No. 41083 (ramp/soak pattern selection) correspond to parameter “PTn”

to be displayed as shown below:

Read-out/write-in data Parameter PTn Contents

0 1 1 to 4 ramp/soak executed
1 2 5 to 8 ramp/soak executed
2 3 1 to 8 ramp/soak executed

－40－

Word data (read-out only) : Function code [04

H

]

Relative

address

Resister

No.

Type Memory contents

Read-out data

Affected by

input range

Remarks or

corresponding

parameter

03E8H 31001 Word Process value (PV)

-1999 to 9999 (within input scale） *

(Displayed PV
value)

03E9H 31002 Word Currently used set value (SV)

-1999 to 9999 (within set value limit） *

(Dsiplayed SV
value)

03EAH 31003 Word Currently used deviation (DV)

-1999 to 9999
(-100 to 100% value of input scale)

*

03EBH 31004 Word MV (output 1)

-300 to 10300（-3.00 to 103.00%）

OUT1

03ECH 31005 Word MV (output 2)

-300 to 10300（-3.00 to 103.00%）

OUT2

03EDH 31006 Word Station No. 0 to 255

STno

03EEH 31007 Word Alarm status

*③ (refer to Section 7.4.)

03EFH 31008 Word Input/main unit abnormal status

*④ (refer to Section 7.4.)

03F0H 31009 Word

Ramp/soak current running
position

0 to 17
*⑥ (refer to Section 7.4.)

STAT

03F1H 31010 Word Heater current

0 to 500（0.0 to 50.0A）

CT

03F2H 31011 Word Timer 1 current count

0 to 9999（0 to 9999 sec）

TM-1

03F3H 31012 Word Timer 2 current count

0 to 9999（0 to 9999 sec）

TM-2
03F4H 31013 (Reserve)
03F5H 31014 (Reserve)
03F6H 31015 Word DI action status

*⑤ (refer to Section 7.4.)

Notes)

• For details of * ② to * ⑥ in the table, refer to Section 7.4.

• The area marked (Do not use) is a reserve area. Do not write in there.

• Register numbers 31002 (currently used SV) and 41003 (face panel set SV) do not become the same

value while switching-SV is active or ramp/soak is under way. (Example: While SV-1 is selected, the

value of SV-1 is read out of register number 31002.) For reading out SV for monitoring, use SV in

register number 31002.

－41－

7.4 Additional Explanation of Address Map

*② Register number 40087, 41087 (read-out/write-in area)

Contents of the communication DI action

Used for requesting a DI action via communication. Once written in, the contents remain held unless

the power is turned off or another value is written in. Pay attention to this point particularly when

canceling the alarm latching.

Read-out data is the data which was written in via communication and is different from hardware DI
action request data (see * ⑤). Do not doubly request the action of the same function as hardware DI.

Bit Contents Read-out Write-in

Bit 1 0 Bit 1 0
0 0 While selecting

face panel set SV

0 0 While selecting

face panel set SV

0 1 Switching-SV selection

0 1 While selecting

SV-1

0 1 While selecting

SV-1
2 (Reserve)
3 (Reserve)
4 (Reserve)
5 Canceling the alarm 1

latching

0:Not requested to cancel the

latching

1:Requested to cancel the latching

0:Not request to cancel the

latching

1:Request to cancel the latching

6 Canceling the alarm 2

latching

0:Not requested to cancel the

latching

1:Requested to cancel the latching

0:Not request to cancel the

latching

1:Request to cancel the latching
7 (Reserve)
8 ALM1 relay timer action 0:Timer action not requested

1:Timer action requested

0:Request to reset timer

1:Request to start timer
9 ALM2 relay timer action 0:Timer action not requested

1:Timer action requested

0:Request to reset timer

1:Request to start timer

10 (Reserve)
11 (Reserve)
12 (Reserve)
13 (Reserve)
14 (Reserve)
15 (Reserve)

*③ Register numbers 30007, 31007 (read-out only area)

Alarm status contents (bit data, Coil numbers 10009 to 10016 grouped in 1 byte.)

Bit Contents Read-out

0 Alarm 1 output

(calculation result of de-energizing alarm)

0:Alarm 1 relay output OFF
1:Alarm 1 relay output ON

1 Alarm 2 output

(calculation result of de-energizing alarm)

0:Alarm 2 relay output OFF

1:Alarm 2 relay output ON
2 (Reserve)
3 HB alarm relay output 0:HB alarm output OFF

1:HB alarm output ON
4 Alarm 1 ON/OFF

0:Alarm 1 OFF，1:Alarm 1 ON
5 Alarm 2 ON/OFF

0:Alarm 2 OFF，1:Alarm 2 ON
6 (Reserve)
7 HB alarm relay output 0:HB alarm output OFF

1:HB alarm output ON

－42－

*④ Register numbers 30008, 31008 (read-out only area)

Input/main unit abnormal status

Bit Contents Read-out

0 Input Lower open-circuit 0:Lower open-circuit absent

1:Lower open -circuit present

1 Input Upper open-circuit 0:Upper open-circuit absent

1:Upper open-circuit present

2 Input under-range 0:Under-range absent

1:Under-range present

3 Input over-range 0:Over-range absent

1:Over-range present
4 (Reserve)
5 (Reserve)
6 Setting range error 0:Setting range normal

1:Setting range abnormal
7 EEPROM error 0:EEPROM normal

1:EEPROM abnormal

*⑤ Register numbers 30015, 31015 (read-out only area)

Contents of DI action status

Hardware DI (DI input terminal) action request information

Bit Contents Read-out

B

it 1 0

0 0 Face panel set SV selected

0 1 Switching-SV selection

0 1 SV-1 selected

2 Control RUN/standby 0:Control RUN requested

1:Control standby requested

3 Auto tuning (standard) 0:AT not requested

1:AT (standard) action requested

4 Auto tuning (low PV type) 0:AT not requested

1:AT (low PV type) action requested

5 Canceling the alarm 1 latching 0:Not requested to cancel the latching

1:Requested to cancel the latching

6 Canceling the alarm 2 latching 0:Not requested to cancel the latching

1:Requested to cancel the latching
7 (Reserve)
8 ALM1 relay timer action 0:Timer action not requested

(timer reset)

1:Timer action requested
9 ALM2 relay timer action 0:Timer action not requested

(timer reset)

1:Timer action requested

10 (Reserve)
11 RUN/RESET selection of

ramp/soak

0:Not requested RUN

(RESET)

1:Requested RUN

12 (Reserve)
13 (Reserve)
14 (Reserve)
15 (Reserve)

－43－

*⑥ Register numbers 30009, 31009 (read-out only area)

Ramp/soak current running position

Read-

out data

Indication of parameter

“STAT”

Running position (status)

0 oFF Stop status of ramp/soak
1 1-rP No. 1 ramp time
2 1-Sk No. 1 soak time
3 2-rP No. 2 ramp time
4 2-Sk No. 2 soak time
5 3-rP No. 3 ramp time
6 3-Sk No. 3 soak time
7 4-rP No. 4 ramp time
8 4-Sk No. 4 soak time

9 5-rP No. 5 ramp time
10 5-Sk No. 5 soak time
11 6-rP No. 6 ramp time
12 6-Sk No. 6 soak time
13 7-rP No. 7 ramp time
14 7-Sk No. 7 soak time
15 8-rP No. 8 ramp time
16 8-Sk No. 8 soak time
17 End End status of ramp/soak

－44－

8. SAMPLE PROGRAM

This section concerns data read-out/write-in sample program by GW-BASIC*1 which operated on Windows 95*1

MS-DOS*

1

PROMPT.

Note that the program shown here is for reference for you to create a program and not for guaranteeing all actions.

Before executing the program, make sure of the communication conditions in the following procedure.
・ Communication speed (baud rate), data length, stop bits and parity bit

Set in this program. Match the conditions with this instrument.

Note) Cautions on using SEKISUI’s RS232C and RS485 converter unit (SI-30A)

In SI-30A, send data are received, added to start of the answer data from the slave station. After

cleared data corresponding to the number of sending bytes, treat the remaining data as the answer data
in the data receiving process.

*1: GW-BASIC, Windows 95 and MS-DOS are registered trademarks of Microsoft Corporation.

－45－

(a) Example of data read-out

Operation:Read-out PV, SV (currently used), DV and MV (control output 1) at a time.

(Continuous word read-out from read-out only area)

Used function code ：04H
Read-out start register No. ：31001 (Engineering unit data)
Read-out word number ：4

1000 '------------------------------------------------------­1010 ' WRITE CONTINUOUS WORDS SAMPLE PROGRAM
1020 '------------------------------------------------------­1030 '
1040 '
1050 '
1060 CLS
1070 DIM CC(255)
1080 '
1100 '-------------- Send data setting ----------------------­1110 CC(1)=&H01 'Station No. = 1
1120 CC(2)=&H06 'Function code = 06H
1130 CC(3)=&H04 'Upper byte of relative address(0439H) of resister No.41082
1140 CC(4)=&H39 'Lower byte of relative address(0439H) of resister No.41082
1150 CC(5)=&H00 'Upper byte of write-in word data(0001H)
1160 CC(6)=&H01 'Lower byte of write-in word data(0001H)
1170 COUNT=6
1200 '
1210 '------------- CRC code calculation of send data -------------­1220 GOSUB 3020 'GOSUB CRC.CALC
1230 CC(7)=CRC.L 'Lower byte of CRC calculation result -> Upper byte in message
1240 CC(8)=CRC.H 'Upper byte of CRC calculation result -> Lower byte in message
1250 COUNT=COUNT+2
1300 '
1310 '------------- Send data ----------------------------­1320 PRINT "Sending data > ";
1330 OPEN "COM1:9600,o,8,1" AS #1 '9600bps, Odd Parity, Data Length=8, Stop bit=1
1340 FOR I=1 TO COUNT
1350 PRINT #1,CHR$(CC(I)); 'Writing in transmission port
1360 PRINT RIGHT$("0"+HEX$(CC(I)),2);" "; 'Displaying on screen
1370 NEXT I
1380 '
1390 FOR I=O TO 30000 :NEXT I 'Interval time
1500 '
1510 '------------- Data receive ---------------------------­1520 PRINT
1530 LENGTH=LOC(1) 'Number of data in receiving buffer
1540 IF LENGTH=0 THEN PRINT "No answer" :END
1550 PRINT "Receiving data < ";
1560 FOR I=1 TO LENGTH
1570 X$=INPUT$(1,#1) 'Taking data from receiving buffer
1580 CC(I)=ASC(X$) 'Digitizing and storing
1590 PRINT RIGHT$("0"+HEX$(CC(I)),2);" "; 'Displaying on screen
1600 NEXT I
1610 CLOSE #1
1620 COUNT=LENGTH-2
1630 GOSUB 3020 'GOSUB CRC.CALC
1700 '
1710 '------------- Transmission error check ----------------------­1720 PRINT

－46－

1730 CRC.L$=RIGHT$("0"+HEX$(CRC.L),2)
1740 CRC.H$=RIGHT$("0"+HEX$(CRC.H),2)
1750 PRINT "CRC calculation = ";CRC.L$;" ";CRC.H$
1760 IF CC(LENGTH-1)<>CRC.L THEN GOTO 1790 'GOTO ER.MESSAGE
1770 IF CC(LENGTH)<>CRC.H THEN GOTO 1790 'GOTO ER.MESSAGE
1780 GOTO 1920 'GOTO PRT.RESULT
1790 'ER.MESSAGE
1800 PRINT "Communication error"
1810 END
1900 '
1910 '------------- Display of result --------------------------­1920 'PRT.RESULT
1930 PRINT
1940 PRINT "Completion of ramp/soak start-up"
1950 END
3000 '
3010 '------------ CRC calculation -----------------------------­3020 'CRC.CALC 'For contents, refer to CRC calculation flow chart
3030 CR=&HFFFF
3040 FOR I=1 TO COUNT
3050 CR=CR XOR CC(I)
3060 FOR J=1 TO 8
3070 CT=CR AND &H1
3080 IF CR<0 THEN CH=1 ELSE CH=0:GOTO 3100 'GOTO CRC.CALC.10
3090 CR=CR AND &H7FFF
3100 'CRC.CALC.10
3110 CR=INT(CR/2)
3120 IF CH=1 THEN CR=CR OR &H4000
3130 IF CT=1 THEN CR=CR XOR &HA001
3140 NEXT J
3150 NEXT I
3160 CRC.L=CR AND &HFF 'Lower byte of CRC calculation
3170 CRC.H=((CR AND &HFF00)/256 AND &HFF) 'Upper byte of CRC calculation
3180 RETURN

－47－

(b) Data write-in example

Operation : Start ramp/soak of No. 1 station via communication

(Single word write-in)

Used function code ：06H
Write-in register No. ：41082 (Table of engineering unit data)
Write-in data ：11082 (Ramp/soak start)

1000 '------------------------------------------------------­1010 ' READ CONTINUOUS WORDS SAMPLE PROGRAM
1020 '------------------------------------------------------­1030 '
1040 '
1050 '
1060 CLS
1070 DIM CC(255)
1080 '
1100 '-------------- Send data setting ----------------------­1110 CC(1)=&H01 'Station No. = 1
1120 CC(2)=&H04 'Function code = 04H
1130 CC(3)=&H03 'Upper byte of relative address(03E8H) of resister No.31001
1140 CC(4)=&HE8 'Lower byte of relative address(03E8H) of resister No.31001
1150 CC(5)=&H00 'Upper byte of read-out word number(0004H)
1160 CC(6)=&H04 'Lower byte of read-out word number(0004H)
1170 COUNT=6
1200 '
1210 '------------- CRC code calculation of send data -------------­1220 GOSUB 3020 'GOSUB CRC.CALC
1230 CC(7)=CRC.L 'Lower byte of CRC calculation result -> Upper byte in message
1240 CC(8)=CRC.H 'Upper byte of CRC calculation result -> Lower byte in message
1250 COUNT=COUNT+2
1300 '
1310 '------------- Send data -------------------------------­1320 PRINT "Sending data > ";
1330 OPEN "COM1:9600,o,8,1" AS #1 '9600bps, Odd Parity, Data Length=8, Stop bit=1
1340 FOR I=1 TO COUNT
1350 PRINT #1,CHR$(CC(I)); 'Writing in transmission port
1360 PRINT RIGHT$("0"+HEX$(CC(I)),2);" "; 'Displaying on screen
1370 NEXT I
1380 '
1390 FOR I=0 TO 30000 :NEXT I 'Interval time
1500 '
1510 '------------- Data receive ----------------------------­1520 PRINT
1530 LENGTH=LOC(1) 'Number of data in receiving buffer
1540 IF LENGTH=0 THEN PRINT "No answer" :END
1550 PRINT "Receiving data < ";
1560 FOR I=1 TO LENGTH
1570 X$=INPUT$(1,#1) 'Taking data from receiving buffer
1580 CC(I)=ASC(X$) 'Digitizing and storing
1590 PRINT RIGHT$("0"+HEX$(CC(I)),2);" "; 'Displaying on screen
1600 NEXT I
1610 CLOSE #1
1620 COUNT=LENGTH-2
1630 GOSUB 3020 'GOSUB CRC.CALC
1700 '
1710 '------------- Transmission error check ----------------------­1720 PRINT

－48－

1730 CRC.L$=RIGHT$("0"+HEX$(CRC.L),2)
1740 CRC.H$=RIGHT$("0"+HEX$(CRC.H),2)
1750 PRINT "CRC calculation = ";CRC.L$;" ";CRC.H$
1760 IF CC(LENGTH-1)<>CRC.L THEN GOTO 1790 'GOTO ER.MESSAGE
1770 IF CC(LENGTH)<>CRC.H THEN GOTO 1790 'GOTO ER.MESSAGE
1780 GOTO 1920 'GOTO PRT.RESULT
1790 'ER.MESSAGE
1800 PRINT "Communication error"
1810 END
1900 '
1910 '------------- Display of result --------------------------­1920 'PRT.RESULT
1930 ' In case of decimal point position(P-dP)=1
1940 PRINT
1950 PV$=HEX$(CC(4))+RIGHT$("0"+HEX$(CC(5)),2) '2 bytes -> 1 word
1960 SV$=HEX$(CC(6))+RIGHT$("0"+HEX$(CC(7)),2) '2 bytes -> 1 word
1970 DV$=HEX$(CC(8))+RIGHT$("0"+HEX$(CC(9)),2) '2 bytes -> 1 word
1980 MV$=HEX$(CC(10))+RIGHT$("0"+HEX$(CC(11)),2) '2 bytes -> 1 word
1990 PRINT "PV =";VAL("&H"+PV$)/10;"degree C" '1 place of decimal
2000 PRINT "SV =";VAL("&H"+SV$)/10;"degree C" '1 place of decimal
2010 PRINT "DV =";VAL("&H"+DV$)/10;"degree C" '1 place of decimal
2020 PRINT "MV1=";VAL("&H"+MV$)/100;"%" 'MV is data of 2 places of decimal
2030 END
3000 '
3010 '------------ CRC calculation -----------------------------­3020 'CRC.CALC 'For contents, refer to CRC calculation flow chart
3030 CR=&HFFFF
3040 FOR I=1 TO COUNT
3050 CR=CR XOR CC(I)
3060 FOR J=1 TO 8
3070 CT=CR AND &H1
3080 IF CR<0 THEN CH=1 ELSE CH=0:GOTO 3100 'GOTO CRC.CALC.10
3090 CR=CR AND &H7FFF
3100 'CRC.CALC.10
3110 CR=INT(CR/2)
3120 IF CH=1 THEN CR=CR OR &H4000
3130 IF CT=1 THEN CR=CR XOR &HA001
3140 NEXT J
3150 NEXT I
3160 CRC.L=CR AND &HFF 'Lower byte of CRC calculation
3170 CRC.H=((CR AND &HFF00)/256 AND &HFF) 'Upper byte of CRC calculation
3180 RETURN

－49－

9. TROUBLESHOOTING

If the communication is unavailable, check the following items.

□ Whether all devices related to communication are turned on.
□ Whether connections are correct.
□ Whether the number of connected instruments and connection distance are as specified
□ Whether communication conditions coincide between the master station (host computer) and slave stations

(PXR)

□ Transmission speed : 9600bps
□ Data length : 8 bits
□ Stop bit : 1 bit
□ Parity : □odd

□even

□none
□ Whether send/receive signal timing conforms to Section 5.4 in this manual.
□ Whether the station No. designated as send destination by the master station coincides with the station No. of

the connected PXR

□ Whether more than one instrument connected on the same transmission line shares the same station No.
□ Whether the station No. of instruments is set at other than 0.

If it’s 0, the communication function does not work.

□ Whether the 11th digit of type cord of this controller is M or V?.

（PXR4□□□□－□□

M

V

□□－□）