FSR HUDDLEVU BRACKET SET User Manual
6. REINSTALL BASE PLATE ASSEMBLY TO TABLE BRACKET AND
MAKE ELECTRICAL CONNECTIONS AS REQUIRED. TIE-WRAP
CABLES TO TIE-TABS AS REQUIRED.
HuddleVU BRACKET SET INSTALLATION INSTRUCTIONS
FSR
1. LOOSEN BASE PLATE SCREWS AND SEPARATE
BASE PLATE FROM TABLE BRACKET. DETERMINE
EQUIPMENT LOCATION AND MOUNT TABLE
BRACKET TO UNDERSIDE OF TABLE WITH
SUPPLIED #8 WOOD SCREWS OR CUSTOMER
SUPPLIED #8 COUNTER-SUNK HARDWARE.
244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
TABLE
INSTALLED
TABLE BRACKET
HV-CTL UNIT CAN BE
REMOVED WITHOUT
REMOVAL OF BASE
PLATE ASSEMBLY
(11) TIE-TAB
TIGHTEN SCREWS
AFTER REINSTALLING
BASE PLATE ASSEMBLY
TO TABLE BRACKET
TABLE BRACKET
(4) #8 COUNTER-SUNK HARDWARE
2. REMOVE AND DISCARD EXISTING SCREWS FROM
HV-CTL UNIT.
HV-CTL
OPTIONAL
PILOT HOLE
PATTERN
3. INSTALL HV-CTL TO BASE PLATE WITH SUPPLIED
#6 HARDWARE.
BASE PLATE ASSEMBLY
12.60
4.50
BE SURE TO PLAN FOR
WIRING / CABLE ROOM IN
FRONT & BACK OF ASSEMBLY
BASE PLATE
REMOVE AND DISCARD
7.43
(4) #6-32 x 3/8" LONG
PAN-HEAD SCREW
43047 LIT1474A
4A.
INSTALLING ONE DV-HSW-41 UNIT:
a.
INSTALL DV-HSW-41 TO BASE PLATE WITH SUPPLIED
M3 HARDWARE.
(4) M3 x 8mm LONG
PAN-HEAD SCREW
DV-HSW-41
OMIT THIS SCREW FOR
EASE OF FIELD SERVICE
5A.
INSTALLING ONE DV-PC2HD UNIT:
a.
INSTALL MOUNTING BRACKET TO DV-PC2HD WITH #6
HARDWARE (MOUNTING BRACKET AND #6 HARDWARE
SUPPLIED WITH DV-PC2HD).
MOUNTING BRACKET
SUPPLIED WITH DV-PC2HD
#6-32 x 1/4" LONG
PAN-HEAD SCREW
SUPPLIED WITH
DV-PC2HD
DV-PC2HD
b. INSTALL DV-PC2HD WITH ATTACHED MOUNTING
BRACKET TO BASE PLATE WITH SUPPLIED #6 HARDWARE
AND #6 HARDWARE SUPPLIED WITH DV-PC2HD.
(2) #6-32 x 3/8" LONG
PAN-HEAD SCREW
4B. INSTALLING TWO DV-HSW-41 UNITS:
a.
REMOVE DV-HSW-41 SIDE BRACKET AND REINSTALL
TO NEW POSITION ONTO BASE PLATE.
SIDE BRACKET
c.
INSTALL DV-HSW-41 TO BASE PLATE WITH SUPPLIED
M3 HARDWARE.
b. INSTALL DV-HSW-41 MOUNTING/SUPPORT BRACKET
TO BASE PLATE WITH SUPPLIED #6 HARDWARE.
(2) #6-32 x 3/8" LONG
MOUNTING/
SUPPORT
BRACKET
OMIT THESE SCREWS FOR
EASE OF FIELD SERVICE
PAN-HEAD SCREW
5B.
INSTALLING TWO DV-PC2HD UNITS:
a.
REMOVE DV-PC2HD SIDE BRACKET. INSTALL MOUNTING
BRACKET TO DV-PC2HD WITH #6 HARDWARE (MOUNTING
BRACKET AND #6 HARDWARE SUPPLIED WITH DV-PC2HD).
INSTALL DV-PC2HD WITH ATTACHED MOUNTING BRACKET
TO BASE PLATE WITH SUPPLIED #6 HARDWARE.
(2) #6-32 x 3/8" LONG
PAN-HEAD SCREW
(2) MOUNTING BRACKET
SUPPLIED WITH DV-PC2HD
(2) #6-32 x 1/4" LONG
PAN-HEAD SCREW
SUPPLIED WITH
DV-PC2HD
#6-32 x 1/4" LONG
PAN-HEAD SCREW
SUPPLIED WITH
b.
REINSTALL SIDE BRACKET TO BASE PLATE AND
SECURE DV-PC2HD WITH #6 HARDWARE SUPPLIED
WITH DV-PC2HD.
(2) DV-PC2HD
(2) #6-32 x 1/4" LONG
PAN-HEAD SCREW
SUPPLIED WITH
DV-PC2HD
DV-PC2HD
(8) M3 x 8mm LONG
PAN-HEAD SCREW
(2) DV-HSW-41
REMOVE
SIDE BRACKET
REINSTALL SIDE BRACKET
Loading...